Pelio-L
For Pelio-L, inverter brand is Victron; battery brand is Pylontech; nominal voltage is 51.2V; communication interface is CAN-bus; minimum firmware is Venus OS v3.50, recorded from its source on 2026-08-12.
- Inverter brand
- Victron verified
- Battery brand
- Pylontech verified
- Battery model
- Pelio-L verified
- Nominal voltage
- 51.2V verified
- Communication interface
- CAN-bus verified
- Minimum firmware
- Venus OS v3.50
- Supported system types
- ESS, Grid Backup, Off-grid
- Module capacity
- 5.12kWh verified
What the source says
CAN-bus Wiring 4. GX Device Settings 5. VEConfigure Settings 6. VE.Direct MPPT Settings 7. Example Wiring Diagram 8. Troubleshooting 9. FAQ and Known Issues The maximum charge and discharge current is limited to 25A, but the data sheet tells me the maximum is 100A. After charging the battery the charge current often changes between 0A and 25A. My system isn't charging at the rated capacity, or my PV is shutting down My system only charges the battery to 52.4V The battery won't charge to 100% 'Internal Error' shown on battery status 'High cell voltage' warning or alarm shown on battery status 10. Further Information DISQUS Victron & Pylontech UP2500, US2000(C/D), US3000, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, Phantom-S, Force-L1 & L2 The combination of Victron products with Pylontech lithium batteries has been tested and certified by the Victron and Pylontech R&D departments. General information about the battery is found in Pylontech's documentation. This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It provides additional and specific information regarding integration with Victron systems. The Pylontech includes a Battery Management System (BMS) with each battery module. This interfaces with the Victron <https://www.victronenergy.com/live/venus-os:start> GX device and can support multiple battery modules connected in parallel. 1. Product & system compatibility <https://www.victronenergy.com/live/_media/battery_compatibility:pylontech_battery.png> Battery | UP2500* | US2000 (Plus/C/D) | US3000(C) | UP5000 & US5000(B) | Pelio-L | Force-L1 & L2 | UF5000 | Nominal voltage | 24V | 48V | 48V | 48V | 51.2V | 48V | 51.2V | Module capacity | 2.55 kWh | 2.4 kWh | 3.5 kWh | 4.8 kwh | 5.12kWh |
— victronenergy.com, retrieved 2026-08-12
Sources disagree
More than one authority states this, and they do not state the same thing. Both are reproduced with the source each came from — deciding between them is yours, not ours.
Inverter brand
victronenergy.com says inverter brand is Victron, as of 2026-08-12.
CAN-bus Wiring 4. GX Device Settings 5. VEConfigure Settings 6. VE.Direct MPPT Settings 7. Example Wiring Diagram 8. Troubleshooting 9. FAQ and Known Issues The maximum charge and discharge current is limited to 25A, but the data sheet tells me the maximum is 100A. After charging the battery the charge current often changes between 0A and 25A. My system isn't charging at the rated capacity, or my PV is shutting down My system only charges the battery to 52.4V The battery won't charge to 100% 'Internal Error' shown on battery status 'High cell voltage' warning or alarm shown on battery status 10. Further Information DISQUS Victron & Pylontech UP2500, US2000(C/D), US3000, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, Phantom-S, Force-L1 & L2 The combination of Victron products with Pylontech lithium batteries has been tested and certified by the Victron and Pylontech R&D departments. General information about the battery is found in Pylontech's documentation. This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It provides additional and specific information regarding integration with Victron systems. The Pylontech includes a Battery Management System (BMS) with each battery module. This interfaces with the Victron <https://www.victronenergy.com/live/venus-os:start> GX device and can support multiple battery modules connected in parallel. 1. Product & system compatibility <https://www.victronenergy.com/live/_media/battery_compatibility:pylontech_battery.png> Battery | UP2500* | US2000 (Plus/C/D) | US3000(C) | UP5000 & US5000(B) | Pelio-L | Force-L1 & L2 | UF5000 | Nominal voltage | 24V | 48V | 48V | 48V | 51.2V | 48V | 51.2V | Module capacity | 2.55 kWh | 2.4 kWh | 3.5 kWh | 4.8 kwh | 5.12kWh |
https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
pylonwebs3.s3.amazonaws.com says inverter brand is Sofar, as of 2026-08-12.
Sofar AN RS485(115200)/C HYD series On-grid Yes Yes V1.2 AN ECH3K ~ 6K-SML-EU LCD: 29.08 CHINT POWER CAN On/off-grid Yes Yes ECA3K ~ 6K-SNL-EU DSP: 05.95 Hardware version Rev1.2.4 AP systems ELS-5K CAN On-grid Yes Yes Software version Rev1.2.X RS485(9600)/CA Sermatec SMT-5K-TL-LV On/off-grid Yes Yes N RS485(115200)/C Zucchetti Centro Azzurro 3000SP On-grid Yes Yes V1.2 AN Sistemi RS485(115200)/C Azzurro HYD3000/6000-ES On-grid Yes Yes V1.2 AN RHI/RAI series CAN On/off-grid PV only Yes 90009 Solis US2000 US2000V2 US3000 US2000C US3000C US5000 US5000-B UP5000 UF5000 Phantom-S Force-L1/L2 Pelio-L Please note that compatibility testing with various inverter brands is currently underway. The list will be updated regularly. For any inquiries, please contact: [email protected] 4/8 Compatibility List of Pylontech ESS and Inverters Ver.2.35.xlsx 48V ESS Last Update:
Nominal voltage
victronenergy.com says nominal voltage is 51.2V, as of 2026-08-12.
CAN-bus Wiring 4. GX Device Settings 5. VEConfigure Settings 6. VE.Direct MPPT Settings 7. Example Wiring Diagram 8. Troubleshooting 9. FAQ and Known Issues The maximum charge and discharge current is limited to 25A, but the data sheet tells me the maximum is 100A. After charging the battery the charge current often changes between 0A and 25A. My system isn't charging at the rated capacity, or my PV is shutting down My system only charges the battery to 52.4V The battery won't charge to 100% 'Internal Error' shown on battery status 'High cell voltage' warning or alarm shown on battery status 10. Further Information DISQUS Victron & Pylontech UP2500, US2000(C/D), US3000, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, Phantom-S, Force-L1 & L2 The combination of Victron products with Pylontech lithium batteries has been tested and certified by the Victron and Pylontech R&D departments. General information about the battery is found in Pylontech's documentation. This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It provides additional and specific information regarding integration with Victron systems. The Pylontech includes a Battery Management System (BMS) with each battery module. This interfaces with the Victron <https://www.victronenergy.com/live/venus-os:start> GX device and can support multiple battery modules connected in parallel. 1. Product & system compatibility <https://www.victronenergy.com/live/_media/battery_compatibility:pylontech_battery.png> Battery | UP2500* | US2000 (Plus/C/D) | US3000(C) | UP5000 & US5000(B) | Pelio-L | Force-L1 & L2 | UF5000 | Nominal voltage | 24V | 48V | 48V | 48V | 51.2V | 48V | 51.2V | Module capacity | 2.55 kWh | 2.4 kWh | 3.5 kWh | 4.8 kwh | 5.12kWh |
https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
pylonwebs3.s3.amazonaws.com says nominal voltage is 48V, as of 2026-08-12.
Sofar AN RS485(115200)/C HYD series On-grid Yes Yes V1.2 AN ECH3K ~ 6K-SML-EU LCD: 29.08 CHINT POWER CAN On/off-grid Yes Yes ECA3K ~ 6K-SNL-EU DSP: 05.95 Hardware version Rev1.2.4 AP systems ELS-5K CAN On-grid Yes Yes Software version Rev1.2.X RS485(9600)/CA Sermatec SMT-5K-TL-LV On/off-grid Yes Yes N RS485(115200)/C Zucchetti Centro Azzurro 3000SP On-grid Yes Yes V1.2 AN Sistemi RS485(115200)/C Azzurro HYD3000/6000-ES On-grid Yes Yes V1.2 AN RHI/RAI series CAN On/off-grid PV only Yes 90009 Solis US2000 US2000V2 US3000 US2000C US3000C US5000 US5000-B UP5000 UF5000 Phantom-S Force-L1/L2 Pelio-L Please note that compatibility testing with various inverter brands is currently underway. The list will be updated regularly. For any inquiries, please contact: [email protected] 4/8 Compatibility List of Pylontech ESS and Inverters Ver.2.35.xlsx 48V ESS Last Update:
Communication interface
victronenergy.com says communication interface is CAN-bus, as of 2026-08-12.
CAN-bus Wiring 4. GX Device Settings 5. VEConfigure Settings 6. VE.Direct MPPT Settings 7. Example Wiring Diagram 8. Troubleshooting 9. FAQ and Known Issues The maximum charge and discharge current is limited to 25A, but the data sheet tells me the maximum is 100A. After charging the battery the charge current often changes between 0A and 25A. My system isn't charging at the rated capacity, or my PV is shutting down My system only charges the battery to 52.4V The battery won't charge to 100% 'Internal Error' shown on battery status 'High cell voltage' warning or alarm shown on battery status 10. Further Information DISQUS Victron & Pylontech UP2500, US2000(C/D), US3000, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, Phantom-S, Force-L1 & L2 The combination of Victron products with Pylontech lithium batteries has been tested and certified by the Victron and Pylontech R&D departments. General information about the battery is found in Pylontech's documentation. This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It provides additional and specific information regarding integration with Victron systems. The Pylontech includes a Battery Management System (BMS) with each battery module. This interfaces with the Victron <https://www.victronenergy.com/live/venus-os:start> GX device and can support multiple battery modules connected in parallel. 1. Product & system compatibility <https://www.victronenergy.com/live/_media/battery_compatibility:pylontech_battery.png> Battery | UP2500* | US2000 (Plus/C/D) | US3000(C) | UP5000 & US5000(B) | Pelio-L | Force-L1 & L2 | UF5000 | Nominal voltage | 24V | 48V | 48V | 48V | 51.2V | 48V | 51.2V | Module capacity | 2.55 kWh | 2.4 kWh | 3.5 kWh | 4.8 kwh | 5.12kWh |
https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
pylonwebs3.s3.amazonaws.com says communication interface is RS485(115200)/CAN, as of 2026-08-12.
Sofar AN RS485(115200)/C HYD series On-grid Yes Yes V1.2 AN ECH3K ~ 6K-SML-EU LCD: 29.08 CHINT POWER CAN On/off-grid Yes Yes ECA3K ~ 6K-SNL-EU DSP: 05.95 Hardware version Rev1.2.4 AP systems ELS-5K CAN On-grid Yes Yes Software version Rev1.2.X RS485(9600)/CA Sermatec SMT-5K-TL-LV On/off-grid Yes Yes N RS485(115200)/C Zucchetti Centro Azzurro 3000SP On-grid Yes Yes V1.2 AN Sistemi RS485(115200)/C Azzurro HYD3000/6000-ES On-grid Yes Yes V1.2 AN RHI/RAI series CAN On/off-grid PV only Yes 90009 Solis US2000 US2000V2 US3000 US2000C US3000C US5000 US5000-B UP5000 UF5000 Phantom-S Force-L1/L2 Pelio-L Please note that compatibility testing with various inverter brands is currently underway. The list will be updated regularly. For any inquiries, please contact: [email protected] 4/8 Compatibility List of Pylontech ESS and Inverters Ver.2.35.xlsx 48V ESS Last Update:
Minimum firmware
victronenergy.com says minimum firmware is Venus OS v3.50, as of 2026-08-12.
CAN-bus Wiring 4. GX Device Settings 5. VEConfigure Settings 6. VE.Direct MPPT Settings 7. Example Wiring Diagram 8. Troubleshooting 9. FAQ and Known Issues The maximum charge and discharge current is limited to 25A, but the data sheet tells me the maximum is 100A. After charging the battery the charge current often changes between 0A and 25A. My system isn't charging at the rated capacity, or my PV is shutting down My system only charges the battery to 52.4V The battery won't charge to 100% 'Internal Error' shown on battery status 'High cell voltage' warning or alarm shown on battery status 10. Further Information DISQUS Victron & Pylontech UP2500, US2000(C/D), US3000, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, Phantom-S, Force-L1 & L2 The combination of Victron products with Pylontech lithium batteries has been tested and certified by the Victron and Pylontech R&D departments. General information about the battery is found in Pylontech's documentation. This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It provides additional and specific information regarding integration with Victron systems. The Pylontech includes a Battery Management System (BMS) with each battery module. This interfaces with the Victron <https://www.victronenergy.com/live/venus-os:start> GX device and can support multiple battery modules connected in parallel. 1. Product & system compatibility <https://www.victronenergy.com/live/_media/battery_compatibility:pylontech_battery.png> Battery | UP2500* | US2000 (Plus/C/D) | US3000(C) | UP5000 & US5000(B) | Pelio-L | Force-L1 & L2 | UF5000 | Nominal voltage | 24V | 48V | 48V | 48V | 51.2V | 48V | 51.2V | Module capacity | 2.55 kWh | 2.4 kWh | 3.5 kWh | 4.8 kwh | 5.12kWh |
https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
pylonwebs3.s3.amazonaws.com says minimum firmware is V1.2, as of 2026-08-12.
Sofar AN RS485(115200)/C HYD series On-grid Yes Yes V1.2 AN ECH3K ~ 6K-SML-EU LCD: 29.08 CHINT POWER CAN On/off-grid Yes Yes ECA3K ~ 6K-SNL-EU DSP: 05.95 Hardware version Rev1.2.4 AP systems ELS-5K CAN On-grid Yes Yes Software version Rev1.2.X RS485(9600)/CA Sermatec SMT-5K-TL-LV On/off-grid Yes Yes N RS485(115200)/C Zucchetti Centro Azzurro 3000SP On-grid Yes Yes V1.2 AN Sistemi RS485(115200)/C Azzurro HYD3000/6000-ES On-grid Yes Yes V1.2 AN RHI/RAI series CAN On/off-grid PV only Yes 90009 Solis US2000 US2000V2 US3000 US2000C US3000C US5000 US5000-B UP5000 UF5000 Phantom-S Force-L1/L2 Pelio-L Please note that compatibility testing with various inverter brands is currently underway. The list will be updated regularly. For any inquiries, please contact: [email protected] 4/8 Compatibility List of Pylontech ESS and Inverters Ver.2.35.xlsx 48V ESS Last Update:
Supported system types
victronenergy.com says supported system types is ESS, Grid Backup, Off-grid, as of 2026-08-12.
CAN-bus Wiring 4. GX Device Settings 5. VEConfigure Settings 6. VE.Direct MPPT Settings 7. Example Wiring Diagram 8. Troubleshooting 9. FAQ and Known Issues The maximum charge and discharge current is limited to 25A, but the data sheet tells me the maximum is 100A. After charging the battery the charge current often changes between 0A and 25A. My system isn't charging at the rated capacity, or my PV is shutting down My system only charges the battery to 52.4V The battery won't charge to 100% 'Internal Error' shown on battery status 'High cell voltage' warning or alarm shown on battery status 10. Further Information DISQUS Victron & Pylontech UP2500, US2000(C/D), US3000, US3000C, US5000, US5000B, UF5000, Pelio-L, UP5000, Phantom-S, Force-L1 & L2 The combination of Victron products with Pylontech lithium batteries has been tested and certified by the Victron and Pylontech R&D departments. General information about the battery is found in Pylontech's documentation. This manual is intended to be used in conjunction with the product manual supplied by Pylontech. It provides additional and specific information regarding integration with Victron systems. The Pylontech includes a Battery Management System (BMS) with each battery module. This interfaces with the Victron <https://www.victronenergy.com/live/venus-os:start> GX device and can support multiple battery modules connected in parallel. 1. Product & system compatibility <https://www.victronenergy.com/live/_media/battery_compatibility:pylontech_battery.png> Battery | UP2500* | US2000 (Plus/C/D) | US3000(C) | UP5000 & US5000(B) | Pelio-L | Force-L1 & L2 | UF5000 | Nominal voltage | 24V | 48V | 48V | 48V | 51.2V | 48V | 51.2V | Module capacity | 2.55 kWh | 2.4 kWh | 3.5 kWh | 4.8 kwh | 5.12kWh |
https://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
pylonwebs3.s3.amazonaws.com says supported system types is On-grid, as of 2026-08-12.
Sofar AN RS485(115200)/C HYD series On-grid Yes Yes V1.2 AN ECH3K ~ 6K-SML-EU LCD: 29.08 CHINT POWER CAN On/off-grid Yes Yes ECA3K ~ 6K-SNL-EU DSP: 05.95 Hardware version Rev1.2.4 AP systems ELS-5K CAN On-grid Yes Yes Software version Rev1.2.X RS485(9600)/CA Sermatec SMT-5K-TL-LV On/off-grid Yes Yes N RS485(115200)/C Zucchetti Centro Azzurro 3000SP On-grid Yes Yes V1.2 AN Sistemi RS485(115200)/C Azzurro HYD3000/6000-ES On-grid Yes Yes V1.2 AN RHI/RAI series CAN On/off-grid PV only Yes 90009 Solis US2000 US2000V2 US3000 US2000C US3000C US5000 US5000-B UP5000 UF5000 Phantom-S Force-L1/L2 Pelio-L Please note that compatibility testing with various inverter brands is currently underway. The list will be updated regularly. For any inquiries, please contact: [email protected] 4/8 Compatibility List of Pylontech ESS and Inverters Ver.2.35.xlsx 48V ESS Last Update:
Sources
- victronenergy.comhttps://www.victronenergy.com/live/battery_compatibility:pylontech_phantom
- pylonwebs3.s3.amazonaws.comhttps://pylonwebs3.s3.amazonaws.com/upload_us/2025/02/10/Compatibility%20List%20of%20Pylontech%20ESS%20and%20Inverters%20Ver.2.35_20250210103505A665.pdf