Withdrawn and superseded ISO standards — page 87 of 246

42437,IS,,ISO 24698-1:2008,"Rubber, raw — Determination of bound acrylonitrile content in acrylonitrile-butadiene rubber (NBR) — Part 1: Combustion (Dumas) method",Caoutchouc brut — Détermination du contenu en acrylonitrile lié dans le caoutchouc acrylonitrile-butadiène (NBR) — Partie 1: Méthode par combustion (Dumas),2008-05-20,1,['83.040.10'],ISO/TC 45/SC 3,9599,,[73998],['en'],7,<p>ISO 24698-1:2008 specifies a method for the determination of the bound acrylonitrile content in NBR by an automatic analyser which uses a combustion process. The method is also applicable to NBR latex.</p>

42438,IS,,ISO 24698-2:2008,"Rubber, raw — Determination of bound acrylonitrile content in acrylonitrile-butadiene rubber (NBR) — Part 2: Kjeldahl method",Caoutchouc brut — Détermination du contenu en acrylonitrile lié dans le caoutchouc acrylonitrile-butadiène (NBR) — Partie 2: Méthode Kjeldahl,2008-05-20,1,['83.040.10'],ISO/TC 45/SC 3,9599,,[73997],['en'],9,<p>ISO 24698-2:2008 specifies a method for the determination of the bound acrylonitrile content in NBR by an automatic analyser which uses the Kjeldahl method.</p>

4138,IS,,ISO 247:1978,Rubber — Determination of ash,Caoutchouc — Détermination des cendres,1978-05-01,2,['83.060'],ISO/TC 45,9599,,[4139],"['en','fr']",3,

4139,IS,,ISO 247:1990,Rubber — Determination of ash,Caoutchouc — Détermination du taux de cendres,1990-11-08,3,['83.060'],ISO/TC 45/SC 2,9599,[4138],[43677],"['en','fr']",3,"<p>The two methods are applicable to raw, compounded and vulcanized rubbers of the families described in ISO 1629. The principle of method A consists in heating a weighed test portion in a crucible over a gas burner, followed by volatilization of the decomposition products and transfer of the crucible to a muffle furnace. The crucible is heated until all the carbonaceous matter has been burnt off and constant mass is attained. In method B a weighed test portion is heated in a crucible in the presence of sulfuric acid, fi

43677,IS,,ISO 247:2006,Rubber — Determination of ash,Caoutchouc — Détermination du taux de cendres,2006-09-14,4,['83.060'],ISO/TC 45/SC 2,9599,[4139],[66372],"['en','fr']",3,"<p>ISO 247:2006 specifies two methods for the determination of ash from raw rubbers, compounded rubbers and vulcanizates. The methods are applicable to raw, compounded or vulcanized rubbers of the M, N, O, R and U families described in ISO 1629, except that:</p><ul><li>Method A is not intended to be used for the determination of ash from compounded or vulcanized rubbers containing chlorine, bromine or iodine.</li><li>Method B is intended to be used for compounded or vulcanized rubbers containing chlorine, bromine or iod

41604,IS,,ISO 2470-1:2009,"Paper, board and pulps — Measurement of diffuse blue reflectance factor — Part 1: Indoor daylight conditions (ISO brightness)","Papier, carton et pâtes — Mesurage du facteur de réflectance diffuse dans le bleu — Partie 1: Conditions d'éclairage intérieur de jour (degré de blancheur ISO)",2009-09-24,1,"['85.060','85.040']",ISO/TC 6,9599,[1466],[69090],"['en','fr']",10,"<p>ISO 2470-1:2009 specifies a method for measuring the diffuse blue reflectance factor (ISO brightness) of pulps, papers and boards.</p><p>ISO 2470-1:2009 is limited in its scope to white and near-white pulps, papers and boards. The measurement can only be made in an instrument in which the ultraviol

33194,IS,,ISO 2470:1973,Paper and board — Measurement of diffuse blue reflectance factor (ISO brightness),Papier et carton — Mesurage du facteur de réflectance diffuse dans le bleu (degré de blancheur ISO),1973-05-01,1,['85.060'],ISO/TC 6,9599,,[7384],"['en','fr']",2,

7384,IS,,ISO 2470:1977,Paper and board — Measurement of diffuse blue reflectance factor (ISO brightness),Papier et carton — Mesurage du facteur de réflectance diffuse dans le bleu (degré de blancheur ISO),1977-02-01,2,['85.060'],ISO/TC 6,9599,[33194],[1466],"['en','fr']",4,

1466,IS,,ISO 2470:1999,"Paper, board and pulps — Measurement of diffuse blue reflectance factor (ISO brightness)","Papier, carton et pâtes — Mesurage du facteur de réflectance diffuse dans le bleu (degré de blancheur ISO)",1999-10-14,3,"['85.060','85.040']",ISO/TC 6,9599,[7384],[41604],"['en','fr']",9,

7385,IS,,ISO 2471:1977,Paper and board — Determination of opacity (paper backing) — Diffuse reflectance method,Papier et carton — Détermination de l'opacité sur fond papier — Méthode de réflexion en lumière diffuse,1977-02-01,2,['85.060'],ISO/TC 6,9599,,[1664],"['en','fr']",4,

1664,IS,,ISO 2471:1998,Paper and board — Determination of opacity (paper backing) — Diffuse reflectance method,Papier et carton — Détermination de l'opacité sur fond papier — Méthode de réflexion en lumière diffuse,1998-02-12,3,['85.060'],ISO/TC 6,9599,[7385],[39771],"['en','fr']",7,

7389,IS,,ISO 2475:1987,"Rubber, chloroprene (CR) — General purpose types — Evaluation procedures",Caoutchouc chloroprène (CR) — Types à usage général — Méthodes d'évaluation,1987-07-16,2,['83.060'],ISO/TC 45/SC 3,9599,,[7390],"['en','fr']",,

7390,IS,,ISO 2475:1990,"Rubber, chloroprene (CR) — General purpose types — Evaluation procedure",Caoutchouc chloroprène (CR) — Types à usage général — Méthode d'évaluation,1990-12-06,3,['83.060'],ISO/TC 45/SC 3,9599,[7389],[27915],"['en','fr']",4,

22195,IS,Cor,ISO 2475:1990/Cor 1:1993,"Rubber, chloroprene (CR) — General purpose types — Evaluation procedure — Technical Corrigendum 1",Caoutchouc chloroprène (CR) — Types à usage général — Méthode d'évaluation — Rectificatif technique 1,1993-04-01,3,['83.060'],ISO/TC 45/SC 3,9599,,[27915],['en'],1,

27915,IS,,ISO 2475:1999,Chloroprene rubber (CR) — General-purpose types — Evaluation procedure,Caoutchouc chloroprène (CR) — Types à usage général — Méthode d'évaluation,1999-12-02,4,['83.060'],ISO/TC 45/SC 3,9599,"[7390,22195]",[55617],"['en','fr']",11,

39056,IS,Amd,ISO 2475:1999/Amd 1:2005,Chloroprene rubber (CR) — General-purpose types — Evaluation procedure — Amendment 1,Caoutchouc chloroprène (CR) — Types à usage général — Méthode d'évaluation — Amendement 1,2005-10-20,4,['83.060'],ISO/TC 45/SC 3,9599,,[55617],['en'],3,

35231,IS,Cor,ISO 2475:1999/Cor 1:2001,Chloroprene rubber (CR) — General-purpose types — Evaluation procedure — Technical Corrigendum 1,Caoutchouc chloroprène (CR) — Types à usage général — Méthode d'évaluation — Rectificatif technique 1,2001-06-14,4,['83.060'],ISO/TC 45/SC 3,9599,,[55617],"['en','fr']",3,

55617,IS,,ISO 2475:2011,Chloroprene rubber (CR) — General-purpose types — Evaluation procedure,Caoutchouc chloroprène (CR) — Types à usage général — Méthode d'évaluation,2011-10-25,5,['83.060'],ISO/TC 45/SC 3,9599,"[39056,35231,27915]",[85294],"['en','fr']",12,"<p>ISO 2475:2011 specifies, for general-purpose chloroprene rubbers (CRs):</p><ul><li>physical and chemical tests on raw rubbers;</li><li>standard materials, standard test formulations, equipment and processing methods for evaluating the vulcanization characteristics.</li></ul>"

7391,IS,,ISO 2476:1980,"Rubber, butadiene (BR) — Solution- polymerized types — Test recipe and evaluation of vulcanization characteristics",Caoutchouc butadiène (BR) — Types polymérisés en solution — Formule d'essai et évaluation des caractéristiques de vulcanisation,1980-10-01,2,['83.060'],ISO/TC 45,9599,,[7392],"['en','fr']",5,

7393,IS,Amd,ISO 2476:1980/Amd 1:1993,"Rubber, butadiene (BR) — Solution- polymerized types — Test recipe and evaluation of vulcanization characteristics — Amendment 1",Caoutchouc butadiène (BR) — Types polymérisés en solution — Formule d'essai et évaluation des caractéristiques de vulcanisation — Amendement 1,1993-01-21,2,['83.060'],ISO/TC 45/SC 3,9599,,"[23844,7392]","['en','fr']",4,

7392,IS,,ISO 2476:1988,"Rubber, butadiene (BR) — Solution-polymerized types — Evaluation procedure",Caoutchouc butadiène (BR) — Types polymérisés en solution — Méthode d'évaluation,1988-12-29,3,['83.060'],ISO/TC 45/SC 3,9599,"[7391,7393]",[23844],"['en','fr']",5,

23844,IS,,ISO 2476:1996,"Rubber, butadiene (BR) — Solution-polymerized types — Evaluation procedures",Caoutchouc butadiène (BR) — Types polymérisés en solution — Méthode d'évaluation,1996-10-24,4,['83.060'],ISO/TC 45/SC 3,9599,"[7392,7393]",[44286],"['en','fr']",8,"<p>Describes physical and chemical tests on raw rubbers and specifies standard materials, standard test formulations, equipment and processing methods for evaluating the vulcanization characteristics of butadiene rubber (BR), including oil-extended types. Replaces the third edition.</p>"

44286,IS,,ISO 2476:2009,Butadiene rubber (BR) — Solution-polymerized types — Evaluation procedures,Caoutchouc butadiène (BR) — Types polymérisés en solution — Méthodes d'évaluation,2009-09-01,5,['83.060'],ISO/TC 45/SC 3,9599,[23844],[61316],"['en','fr','ru']",17,"<p>ISO 2476:2009 specifies:</p><ul><li>physical and chemical tests on raw rubbers;</li><li>standard materials, standard test formulations, equipment and processing methods for evaluating the vulcanization characteristics of solution-polymerized butadiene rubbers (BR), including oil-extended types (OEBR), and the tensile stress-strain properties of vulcanized mixes.</li></ul>"

7395,IS,,ISO 2477:1973,Shaped insulating refractory products — Determination of the permanent change in dimensions on heating,Produits réfractaires isolants façonnés — Détermination de la variation permanente de dimensions sous l'action de la chaleur,1973-09-01,1,['81.080'],ISO/TC 33,9599,,[7396],"['en','fr']",3,

7396,IS,,ISO 2477:1987,Shaped insulating refractory products — Determination of permanent change in dimensions on heating,Produits réfractaires isolants façonnés — Détermination de la variation permanente de dimensions sous l'action de la chaleur,1987-11-05,2,['81.080'],ISO/TC 33,9599,[7395],"[21568,36181]","['en','fr']",3,<p>Specifies a method for determining the permanent change in dimensions on heating of a shaped insulating refractory product. A figure shows the position of measurements and mounting of the test pieces in the furnace. This second edition cancels and replaces the first edition (1973).</p>

7397,IS,,ISO 2478:1973,Dense shaped refractory products — Determination of the permanent changes in dimensions on heating,Produits réfractaires denses façonnés — Détermination de la variation permanente de dimensions sous l'action de la chaleur,1973-11-01,1,['81.080'],ISO/TC 33,9599,,[7398],"['en','fr']",5,

7398,IS,,ISO 2478:1987,Dense shaped refractory products — Determination of permanent change in dimensions on heating,Produits réfractaires façonnés denses — Détermination de la variation permanente de dimensions sous l'action de la chaleur,1987-10-22,2,['81.080'],ISO/TC 33,9599,[7397],"[21569,88936]","['en','fr']",4,

53032,IS,,ISO 248-1:2011,"Rubber, raw — Determination of volatile-matter content — Part 1: Hot-mill method and oven method",Caoutchouc brut — Détermination des matières volatiles — Partie 1: Méthode par mélangeage à chaud et méthode par étuvage,2011-10-10,1,['83.040.10'],ISO/TC 45/SC 3,9599,[38724],[76771],"['en','fr','ru']",13,"<p>ISO 248-1:2011 specifies two methods for the determination of volatile-matter content in raw rubbers by using a hot mill or an oven.</p><p>The methods are applicable to the determination of the volatile-matter content in the 'R' group of rubbers listed in ISO 1629. These are rubbers having an unsaturated carbon chain, for example natural rubber and synthetic rubbe

4140,IS,,ISO 248:1979,"Rubbers, raw — Determination of volatile matter content",Caoutchoucs bruts — Détermination des matières volatiles,1979-11-01,2,['83.040.10'],ISO/TC 45,9599,[6835],[4141],"['en','fr']",2,

4141,IS,,ISO 248:1991,"Rubbers, raw — Determination of volatile-matter content",Caoutchoucs bruts — Détermination des matières volatiles,1991-10-17,3,['83.040.10'],ISO/TC 45/SC 2,9599,[4140],[38724],"['en','fr']",5,"<p>Specifies two methods, a hot-mill and an oven method, for the determination of moisture and other volatile-matter. This third edition cancels and replaces the second edition (1979). Annex A is for information only.</p>"

51796,IS,,ISO 248-2:2012,"Rubber, raw — Determination of volatile-matter content — Part 2: Thermogravimetric methods using an automatic analyser with an infrared drying unit",Caoutchouc brut — Détermination des matières volatiles — Partie 2: Méthodes thermogravimétriques utilisant un analyseur automatique avec une unité de séchage infrarouge,2012-04-20,1,['83.040.10'],ISO/TC 45/SC 3,9599,,[75627],"['en','ru']",10,

38724,IS,,ISO 248:2005,"Rubber, raw — Determination of volatile-matter content",Caoutchouc brut — Détermination des matières volatiles,2005-06-27,4,['83.040.10'],ISO/TC 45/SC 2,9599,[4141],[53032],"['en','fr']",9,"<p>ISO 248:2005 specifies two methods, a hot-mill method and an oven method, for the determination of moisture and other volatile-matter content in raw rubbers.</p><p>These methods are applicable to the determination of the volatile-matter content in the R-group of rubbers listed in ISO 1629 which are rubbers having an unsaturated carbon chain, for example, natural rubber and synthetic rubbers derived at least partly from diolefins.</p><p>ISO 248:2005 may also be applicable to othe

42444,IS,,ISO 24801-1:2007,Recreational diving services — Safety related minimum requirements for the training of recreational scuba divers — Part 1: Level 1 — Supervised diver,Services relatifs à la plongée de loisirs — Exigences minimales liées à la sécurité concernant la formation des plongeurs en scaphandre autonome pratiquant la plongée de loisirs — Partie 1: Niveau 1 — Plongeur encadré,2007-02-09,1,"['03.200.99','03.080.30']",ISO/TC 228,9599,,[60460],"['en','fr']",11,"<p>ISO 24801-1:2007 specifies the competencies that a scuba diver has to have achieved in order for a training organization to award the scuba diver certification indicating that he has met or exceeded scuba diver level 1

42448,IS,,ISO 24801-2:2007,Recreational diving services — Safety related minimum requirements for the training of recreational scuba divers — Part 2: Level 2 — Autonomous diver,Services relatifs à la plongée de loisirs — Exigences minimales liées à la sécurité concernant la formation des plongeurs en scaphandre autonome pratiquant la plongée de loisirs — Partie 2: Niveau 2 — Plongeur autonome,2007-02-09,1,"['03.200.99','03.080.30']",ISO/TC 228,9599,,[60461],"['en','fr']",14,"<p>ISO 24801-2:2007 specifies the competencies that a scuba diver has to have achieved in order for a training organization to award the scuba diver certification indicating that he has met or exceeded scuba diver level

42449,IS,,ISO 24801-3:2007,Recreational diving services — Safety related minimum requirements for the training of recreational scuba divers — Part 3: Level 3 — Dive leader,Services relatifs à la plongée de loisirs — Exigences minimales liées à la sécurité concernant la formation des plongeurs en scaphandre autonome pratiquant la plongée de loisirs — Partie 3: Niveau 3 — Guide de palanquée,2007-02-09,1,"['03.200.99','03.080.30']",ISO/TC 228,9599,,[60462],"['en','fr']",11,"<p>ISO 24801-3:2007 specifies the competencies that a scuba diver has to have achieved in order for a training organization to award the scuba diver certification indicating that he has met or exceeded scuba diver level 3 -

42445,IS,,ISO 24802-1:2007,Recreational diving services — Safety related minimum requirements for the training of scuba instructors — Part 1: Level 1,Services relatifs à la plongée de loisirs — Exigences minimales liées à la formation des moniteurs de plongée subaquatique — Partie 1: Niveau 1,2007-03-01,1,"['03.100.30','03.200.99','03.080.30']",ISO/TC 228,9599,,[60463],"['en','fr']",8,"<p>ISO 24802-1:2007 specifies the competencies that a scuba instructor has to have achieved in order for a training organization to award the scuba instructor certification indicating that he has met or exceeded scuba instructor level 1 and specifies assessment of these competencies. </p><p>It also specifies c

42447,IS,,ISO 24802-2:2007,Recreational diving services — Safety related minimum requirements for the training of scuba instructors — Part 2: Level 2,Services relatifs à la plongée de loisirs — Exigences minimales liées à la formation des moniteurs de plongée subaquatique — Partie 2: Niveau 2,2007-03-01,1,"['03.100.30','03.200.99','03.080.30']",ISO/TC 228,9599,,[60464],"['en','fr']",9,"<p>ISO 24802-2:2007 specifies the competencies that a scuba instructor has to have achieved in order for a training organization to award the scuba instructor certification indicating that he has met or exceeded scuba instructor level 2 and specifies assessment of these competencies. </p><p>It also specifies c

42446,IS,,ISO 24803:2007,Recreational diving services — Requirements for recreational scuba diving service providers,Services relatifs à la plongée de loisirs — Exigences relatives aux prestataires de services de plongée de loisirs en scaphandre autonome,2007-02-09,1,"['03.200.99','03.080.30']",ISO/TC 228,9599,,"[68276,60465]","['en','fr']",8,"<p>ISO 24803:2007 specifies requirements for service providers in the field of recreational scuba diving.</p><p>It specifies three areas of service provision:</p><ul><li>training and education,</li><li>organized and guided diving for certified divers,</li><li>rental of diving equipment.</li></ul><p>Service providers may offer one or more of these servi

59987,IS,,ISO 24817:2015,"Petroleum, petrochemical and natural gas industries — Composite repairs for pipework — Qualification and design, installation, testing and inspection","Industries du pétrole, de la pétrochimie et du gaz naturel — Réparations en matériau composite pour canalisations — Qualification et conception, installation, essai et inspection",2015-07-20,1,['75.180.20'],ISO/TC 67/SC 6,9599,[42451],[70958],"['en','fr']",85,"<p>ISO 24817:2015 gives requirements and recommendations for the qualification and design, installation, testing, and inspection for the external application of composite repair systems to corroded or damaged pipework, pipelines, tanks, and vessels used in the

4142,IS,,ISO 249:1974,Raw natural rubber — Determination of dirt,Caoutchouc naturel brut — Détermination de la teneur en impuretés,1974-04-01,1,['83.040.10'],ISO/TC 45,9599,,[4143],"['en','fr']",3,

4143,IS,,ISO 249:1987,"Rubber, raw natural — Determination of dirt content",Caoutchouc naturel brut — Détermination de la teneur en impuretés,1987-12-03,2,['83.040.10'],ISO/TC 45,9599,[4142],[2186],"['en','fr']",4,

2186,IS,,ISO 249:1995,"Rubber, raw natural — Determination of dirt content",Caoutchouc naturel brut — Détermination de la teneur en impuretés,1995-12-21,3,['83.040.10'],ISO/TC 45/SC 3,9599,[4143],"[63604,43678]","['en','fr']",6,<p>Specifies a method for the determination of the dirt content of raw natural rubber. Not applicable to dirt present as surface contamination. Replaces the second edition which has been technically revised.</p>

63604,IS,,ISO 249:2014,"Rubber, raw natural — Determination of dirt content",Caoutchouc naturel brut — Détermination de la teneur en impuretés,2014-07-30,4,['83.040.10'],ISO/TC 45/SC 3,9599,[2186],[70283],"['en','fr','ru']",10,<p>ISO 249:2014 specifies a method for the determination of the dirt content of raw natural rubber. It is not applicable to dirt present as surface contamination.</p>

7411,IS,,ISO 2490:1975,"Single-start solid (monobloc) gear hobs with axial keyway, 1 to 20 module and 1 to 20 diametral pitch — Nominal dimensions","Fraises-mères monoblocs à une entrée, à entraînement par clavette, de modules 1 à 20 et de diamétral pitches 1 à 20 — Dimensions nominales",1975-06-01,1,['21.200'],ISO/TC 60,9599,,[7412],"['en','fr']",3,

7412,IS,,ISO 2490:1996,"Single-start solid (monobloc) gear hobs with tenon drive or axial keyway, 1 to 40 module — Nominal dimensions","Fraises-mères monoblocs à un filet, à entraînement par tenon ou par clavette, de modules 1 à 40 — Dimensions nominales",1996-11-07,2,['21.200'],ISO/TC 60,9599,[7411],[33092],"['en','fr']",4,"<p>Specifies the nominal dimensions of single start monobloc gear hobs with tenon drive or axial keyway, 1 to 40 module. Replaces the first edition.</p>"

42633,IS,,ISO 24917:2010,Space systems — General test requirements for launch vehicles,Systèmes spatiaux — Exigences générales d'essai pour véhicules lanceurs,2010-09-30,1,['49.140'],ISO/TC 20/SC 14,9599,,[71612],['en'],35,"<p>ISO 24917:2010 establishes general test requirements for launch vehicles equipped with liquid-propellant engines, launched from stationary ground-, sea- and air-based launchers, in all phases of their development.</p>"

7415,IS,,ISO 2493:1973,Paper and board — Determination of stiffness — Static bending method,Papier et carton — Détermination de la rigidité — Méthode par flexion statique,1973-11-01,1,['85.060'],ISO/TC 6/SC 2,9599,,[7416],"['en','fr']",3,

7416,IS,,ISO 2493:1992,Paper and board — Determination of resistance to bending,Papier et carton — Détermination de la résistance à la flexion,1992-09-17,2,['85.060'],ISO/TC 6/SC 2,9599,[7415],"[29894,51696,52429]","['en','fr']",3,"<p>Applies to the measurement of the resistance to bending within the range 20 mN to 10 000 mN, but on some instruments down to about 2 mN. Does not apply to corrugated boards but may be applied to the components of such boards. The method is based on the beam principle and is applicable only to instruments which use a bending angle of 7,5° or 15°.</p>"

52429,IS,,ISO 2493-2:2011,Paper and board — Determination of bending resistance — Part 2: Taber-type tester,Papier et carton — Détermination de la résistance à la flexion — Partie 2: Rigidimètre Taber,2011-11-10,1,['85.060'],ISO/TC 6/SC 2,9599,[7416],[76346],"['en','fr']",9,"<p>ISO 2493-2:2011 specifies procedures to measure the bending resistance of paper and paperboard.</p><p>ISO 2493-2:2011 is used to determine the bending moment required to deflect the free end of a 38 mm wide vertically clamped specimen by 15° when the load is applied at a bending length of 50 mm. For boards that tend to be permanently deformed if bent through 15°, the half bending angle, i.e. 7,5°, can be used. The ben

7417,IS,,ISO 2494:1974,Paper and board — Recommended procedure for the determination of roughness — Constant-pressure air-flow method,Papier et carton — Mode opératoire recommandé pour la détermination de la rugosité — Méthode du débit d'air sous pression constante,1974-02-01,1,['85.060'],ISO/TC 6/SC 2,9599,,"[16216,16217]","['en','fr']",4,

7418,IS,,ISO 2495:1972,Iron blue pigments for paints,Bleus de fer pour peintures,1972-08-01,1,['87.060.10'],ISO/TC 256,9599,,[7419],"['en','fr']",2,

3612,IS,,ISO 25:1976,Cinematography — Camera usage of 16 mm motion-picture film — Specifications,Cinématographie — Emploi du film cinématographique 16 mm dans la caméra — Spécifications,1976-07-01,1,['37.060.10'],ISO/TC 36,9599,,[21562],"['en','fr']",1,

7430,IS,,ISO 2503:1983,"Pressure regulators for gas cylinders used in welding, cutting and allied processes","Détendeurs pour bouteilles à gaz utilisés pour le soudage, le coupage et les techniques connexes",1983-12-01,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[21030],"['en','fr']",7,

7431,IS,Add,ISO 2503:1983/Add 1:1984,"Pressure regulators for gas cylinders used in welding, cutting and allied processes — Addendum 1","Détendeurs pour bouteilles à gaz utilisés pour le soudage, le coupage et les techniques connexes — Additif 1",1984-07-01,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[21030],"['en','fr']",6,

21030,IS,,ISO 2503:1998,"Gas welding equipment — Pressure regulators for gas cylinders used in welding, cutting and allied processes up to 300 bar","Matériel de soudage aux gaz — Détendeurs pour bouteilles de gaz utilisés pour le soudage, le coupage et les techniques connexes jusqu'à 300 bar",1998-03-26,2,['25.160.30'],ISO/TC 44/SC 8,9599,"[7430,7431]",[40644],"['en','fr']",16,

7432,IS,,ISO 2504:1973,Radiography of welds and viewing conditions for films — Utilization of recommended patterns of image quality indicators (I.Q.I.),Radiographie de soudures et conditions d'observation des films — Emploi des types recommandés d'indicateurs de qualité d'image (I.Q.I.),1973-02-01,1,['25.160.40'],ISO/TC 44/SC 5,9599,,[7433],"['en','fr']",5,<p>Relates to the conditions for use of recommended patterns of image quality indicators (I.Q.I.) for radiography of welds and viewing conditions for films.</p>

7435,IS,,ISO 2505-1:1994,Thermoplastics pipes — Longitudinal reversion — Part 1: Determination methods,Tubes en matières thermoplastiques — Retrait longitudinal à chaud — Partie 1: Méthodes de détermination,1994-12-01,1,['23.040.20'],ISO/TC 138/SC 5,9599,"[7437,7434,8831]",[33601],"['en','fr']",3,"<p>Specifies two methods for determining the longitudinal reversion of thermoplstics pipes, to be carried out in liquid or in air. Applies to all thermoplastics pipes with smooth internal and external walls of constant cross-section. Does not apply to non-smooth structured-wall thermoplastics pipes.</p>"

7434,IS,,ISO 2505:1981,Unplasticized polyvinyl chloride (PVC) pipes — Longitudinal reversion — Test methods and specification,Tubes en polychlorure de vinyle (PVC) non plastifié — Retrait longitudinal à chaud — Méthodes d'essai et spécification,1981-11-01,2,['23.040.20'],ISO/TC 138/SC 5,9599,,"[7435,7436]","['en','fr']",3,

7436,IS,,ISO 2505-2:1994,Thermoplastics pipes — Longitudinal reversion — Part 2: Determination parameters,Tubes en matières thermoplastiques — Retrait longitudinal à chaud — Partie 2: Paramètres de détermination,1994-12-01,1,['23.040.20'],ISO/TC 138/SC 5,9599,"[7437,7434,8831]",[33601],"['en','fr']",5,"<p>Specifies the parameters for the determination of the longitudinal reversion of thermoplastics pipes in accordance with methods A and B specified in ISO 2505-1, using a liquid bath or an air oven. Applies to all pipes of thermoplastics material given in claus 3 and 4. Gives in annex A recommendations for maximum levels of reversion as a function of certain pipe materials.</p>"

28937,IS,Cor,ISO 2505-2:1994/Cor 1:1997,Thermoplastics pipes — Longitudinal reversion — Part 2: Determination parameters — Technical Corrigendum 1,Tubes en matières thermoplastiques — Retrait longitudinal à chaud — Partie 2: Paramètres de détermination — Rectificatif technique 1,1997-05-15,1,['23.040.20'],ISO/TC 138/SC 5,9599,,[33601],"['en','fr']",1,

33601,IS,,ISO 2505:2005,Thermoplastics pipes — Longitudinal reversion — Test method and parameters,Tubes en matières thermoplastiques — Retrait longitudinal à chaud — Méthode d'essai et paramètres,2005-05-25,3,['23.040.20'],ISO/TC 138/SC 5,9599,"[28937,7435,7436]",[82021],"['en','fr']",5,"<p>ISO 2505:2005 specifies a method for determining the longitudinal reversion of thermoplastics pipes, to be carried out in either a liquid or in air. In case of dispute, heated liquid is used as the reference. ISO 2505:2005 is applicable to all thermoplastics pipes with smooth internal and external walls of constant cross-section. It is not applicable to non-smooth structured-wall thermoplastics pipes.</p

7437,IS,,ISO 2506:1981,Polyethylene pipes (PE) — Longitudinal reversion — Test methods and specification,Tubes en polyéthylène (PE) — Retrait longitudinal à chaud — Méthodes d'essai et spécification,1981-12-01,2,['23.040.20'],ISO/TC 138/SC 5,9599,,"[7435,7436]","['en','fr']",3,

20854,IS,,ISO 2507-1:1995,Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method,Tubes et raccords en matières thermoplastiques — Température de ramollissement Vicat — Partie 1: Méthode générale d'essai,1995-02-02,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 5,9599,[7438],"[85780,89067]","['en','fr']",4,"<p>The method specified is based on determining the temperature at which a standard indenter, under a force of 50 N ± 1 N, penetrates 1 mm into the surface of a test piece cut from the wall of a pipe or fitting while the temperature is raised at a constant rate. Is applicable only to thermoplastics materials for which it is possible to measure the temper

7438,IS,,ISO 2507:1982,Unplasticized polyvinyl chloride (PVC) pipes and fittings — Vicat softening temperature — Test method and specification,Tubes et raccords en polychlorure de vinyle (PVC) non plastifié — Température de ramollissement Vicat — Méthode d'essai et spécification,1982-12-01,2,"['23.040.45','23.040.20']",ISO/TC 138/SC 5,9599,[6833],"[20854,20855]","['en','fr']",4,

20855,IS,,ISO 2507-2:1995,Thermoplastics pipes and fittings — Vicat softening temperature — Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes,Tubes et raccords en matières thermoplastiques — Température de ramollissement Vicat — Partie 2: Conditions particulières d'essai pour tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) ou en poly(chlorure de vinyle) chloré (PVC-C) et tubes en poly(chlorure de vinyle) à résistance au choc améliorée (PVC-HI),1995-02-02,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 5,9599,[7438],"[89067,857

20856,IS,,ISO 2507-3:1995,Thermoplastics pipes and fittings — Vicat softening temperature — Part 3: Test conditions for acrylonitrile/butadiene/styrene (ABS) and acrylonitrile/styrene/acrylic ester (ASA) pipes and fittings,Tubes et raccords en matières thermoplastiques — Température de ramollissement Vicat — Partie 3: Conditions particulières d'essai pour tubes et raccords en acrylonitrile/butadiène/styrène (ABS) et en acrylonitrile/styrène/ester acrylique (ASA),1995-02-02,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 5,9599,,"[89067,85778]","['en','fr']",4,"<p>Specifies the particular test conditions for determining the Vicat softening temperature of ABS and ASA pipes and fittings (the genera

7440,IS,,ISO 2509:1973,Cork — Sound absorbing expanded pure agglomerated cork in tiles — Characteristics,Liège — Aggloméré expansé pur absorbant acoustique en dalles — Caractéristiques,1973-07-01,1,"['79.100','91.100.60']",ISO/TC 87,9599,,[7441],"['en','fr']",2,

4145,IS,,ISO 251:1976,Conveyor belts — Widths and lengths,Courroies transporteuses — Largeurs et longueurs,1976-07-01,1,['53.040.10'],ISO/TC 41,9599,,[4146],"['en','fr']",1,

4146,IS,,ISO 251:1987,Conveyor belts — Widths and lengths,Courroies transporteuses — Largeurs et longueurs,1987-07-16,2,['53.040.20'],ISO/TC 41/SC 3,9599,[4145],[27295],"['en','fr']",1,"<p>This second edition cancels and replaces the first edition (1976). Specifies the width of belts and corresponding tolerances, and also tolerances (the lengths of conveyor belts are not standardized). Tabulates the nominal widths from 300 mm up to and including 3200 mm.</p>"

27295,IS,,ISO 251:2003,Conveyor belts with textile carcass — Widths and lengths,Courroies transporteuses à carcasse textile — Largeurs et longueurs,2003-06-20,3,['53.040.20'],ISO/TC 41/SC 3,9599,[4146],[61040],"['en','fr']",3,<p>ISO 251:2003 specifies the widths and lengths of conveyor belts with a textile carcass. It also specifies the corresponding tolerances.</p><p>The lengths of conveyor belts are not standardized.</p>

61040,IS,,ISO 251:2012,Conveyor belts with textile carcass — Widths and lengths,Courroies transporteuses à carcasse textile — Largeurs et longueurs,2012-10-01,4,['53.040.20'],ISO/TC 41/SC 3,9599,[27295],[88482],"['en','fr']",3,

7442,IS,,ISO 2510:1973,Cork — Sound absorbing composition cork in tiles — Characteristics,Liège — Aggloméré composé absorbant acoustique en dalles — Caractéristiques,1973-07-01,1,"['79.100','91.100.60']",ISO/TC 87,9599,,[7443],"['en','fr']",2,

72360,IS,,ISO 25110:2017,Electronic fee collection — Interface definition for on-board account using integrated circuit card (ICC),Perception du télépéage — Définition d'interface pour compte de bord utilisant une carte à circuit intégré (ICC),2017-10-24,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,[62476],[89711],"['en','fr']",34,<p>ISO 25110:2017 defines the data transfer models between roadside equipment (RSE) and integrated circuit card (ICC) and the interface descriptions between the RSE and on-board equipment (OBE) for on-board accounts using the ICC. It also provides examples of interface definitions and transactions deployed in several countries.</p>

45047,IS,,ISO 25119-1:2010,Tractors and machinery for agriculture and forestry — Safety-related parts of control systems — Part 1: General principles for design and development,Tracteurs et matériels agricoles et forestiers — Parties des systèmes de commande relatives à la sécurité — Partie 1: Principes généraux pour la conception et le développement,2010-05-27,1,"['65.060.01','35.240.99']",ISO/TC 23/SC 19,9599,,[69025],"['en','fr']",24,"<p>ISO 25119-1:2010 sets out general principles for the design and development of safety-related parts of control systems (SRP/CS) on tractors used in agriculture and forestry, and on self-propelled ride-on machines and mounted, semi-mounted and trailed mach

45048,IS,,ISO 25119-2:2010,Tractors and machinery for agriculture and forestry — Safety-related parts of control systems — Part 2: Concept phase,Tracteurs et matériels agricoles et forestiers — Parties des systèmes de commande relatives à la sécurité — Partie 2: Phase de projet,2010-05-27,1,"['65.060.01','35.240.99']",ISO/TC 23/SC 19,9599,,[69026],"['en','fr']",37,"<p>ISO 25119-2:2010 specifies the concept phase of the development of safety-related parts of control systems (SRP/CS) on tractors used in agriculture and forestry, and on self-propelled ride-on machines and mounted, semi-mounted and trailed machines used in agriculture. It can also be applied to municipal equipment (e.g. street‑s

69026,IS,,ISO 25119-2:2018,Tractors and machinery for agriculture and forestry — Safety-related parts of control systems — Part 2: Concept phase,Tracteurs et matériels agricoles et forestiers — Parties des systèmes de commande relatives à la sécurité — Partie 2: Phase de projet,2018-10-12,2,"['65.060.01','35.240.99']",ISO/TC 23/SC 19,9599,[45048],[78306],"['en','fr']",47,"<p>This document specifies the concept phase of the development of safety-related parts of control systems (SRP/CS) on tractors used in agriculture and forestry and on self-propelled ride-on machines and mounted, semi-mounted and trailed machines used in agriculture. It can also be applied to mobile municipal equipment (e.g

45049,IS,,ISO 25119-3:2010,"Tractors and machinery for agriculture and forestry — Safety-related parts of control systems — Part 3: Series development, hardware and software","Tracteurs et matériels agricoles et forestiers — Parties des systèmes de commande relatives à la sécurité — Partie 3: Développement en série, matériels et logiciels",2010-05-27,1,"['65.060.01','35.240.99']",ISO/TC 23/SC 19,9599,,[69027],"['en','fr']",57,"<p>ISO 25119-3:2010 provides general principles for the series development, hardware and software of safety-related parts of control systems (SRP/CS) on tractors used in agriculture and forestry, and on self-propelled ride-on machines and mounted, semi-mounted and trai

45050,IS,,ISO 25119-4:2010,"Tractors and machinery for agriculture and forestry — Safety-related parts of control systems — Part 4: Production, operation, modification and supporting processes","Tracteurs et matériels agricoles et forestiers — Parties des systèmes de commande relatives à la sécurité — Partie 4: Procédés de production, de fonctionnement, de modification et d'entretien",2010-05-27,1,"['65.060.01','35.240.99']",ISO/TC 23/SC 19,9599,,[69028],"['en','fr']",22,"<p>ISO 25119-4:2010 provides general principles for the production, operation, modification and supporting processes of safety-related parts of control systems (SRP/CS) on tractors used in agriculture and forestry, and on s

42772,IS,,ISO 25137-1:2009,Plastics — Sulfone polymer moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Matériaux pour moulage et extrusion à base de polymères sulfone — Partie 1: Système de désignation et base de spécifications,2009-01-06,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[77545],"['en','fr']",11,"<p>ISO 25137-1:2009 establishes a system of designation for sulfone polymer moulding and extrusion materials, including polysulfone (PSU), polyethersulfone (PESU) and polyphenylsulfone (PPSU), which may be used as the basis for specifications.</p><p>The types of sulfone plastic are differentiated from each other by a classification system ba

42773,IS,,ISO 25137-2:2009,Plastics — Sulfone polymer moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Matériaux pour moulage et extrusion à base de polymères sulfone — Partie 2: Préparation des éprouvettes et détermination des propriétés,2009-01-05,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[77546],"['en','fr']",5,"<p>ISO 25137-2:2009 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of sulfone polymer moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before test

42783,IS,,ISO 25177:2008,Soil quality — Field soil description,Qualité du sol — Description du sol sur le terrain,2008-11-12,1,['13.080.01'],ISO/TC 190,9599,[19237],[69585],"['en','fr']",35,"<p>ISO 25177:2008 is a guide for describing the soil and its environmental context at a given site. Sites can be natural, near-natural, urban or industrial. It is important to realize that a number of soil samples can be taken at a site to support the soil description. The information provided by the descriptions in ISO 25177:2008 provides the context for the presentation of results from analyses undertaken on soil samples.</p>"

42785,IS,,ISO 25178-2:2012,"Geometrical product specifications (GPS) — Surface texture: Areal — Part 2: Terms, definitions and surface texture parameters","Spécification géométrique des produits (GPS) — État de surface: Surfacique — Partie 2: Termes, définitions et paramètres d'états de surface",2012-03-28,1,['17.040.20'],ISO/TC 213,9599,,[74591],"['en','fr']",47,"<p>ISO 25178-2:2012 specifies terms, definitions and parameters for the determination of surface texture by areal methods. </p>"

42786,IS,,ISO 25178-601:2010,Geometrical product specifications (GPS) — Surface texture: Areal — Part 601: Nominal characteristics of contact (stylus) instruments,Spécification géométrique des produits (GPS) — État de surface: Surfacique — Partie 601: Caractéristiques nominales des instruments à contact (à palpeur),2010-06-22,1,['17.040.20'],ISO/TC 213,9599,,[79673],"['en','fr']",17,<p>ISO 25178-601:2010 defines the metrological characteristics of contact (stylus) areal surface texture measuring instruments.</p>

43920,IS,,ISO 25178-602:2010,Geometrical product specifications (GPS) — Surface texture: Areal — Part 602: Nominal characteristics of non-contact (confocal chromatic probe) instruments,Spécification géométrique des produits (GPS) — État de surface: Surfacique — Partie 602: Caractéristiques nominales des instruments sans contact (à capteur confocal chromatique),2010-06-22,1,['17.040.20'],ISO/TC 213,9599,,[79674],"['en','fr']",31,<p>ISO 25178-602:2010 specifies the design and metrological characteristics of a particular non-contact instrument for measuring surface texture using a confocal chromatic probe based on axial chromatic dispersion of white light.</p>

61236,IS,,ISO 25178-603:2013,Geometrical product specifications (GPS) — Surface texture: Areal — Part 603: Nominal characteristics of non-contact (phase-shifting interferometric microscopy) instruments,Spécification géométrique des produits (GPS) — État de surface: Surfacique — Partie 603: Caractéristiques nominales des instruments sans contact (microscopes interférométriques à glissement de franges),2013-09-25,1,['17.040.20'],ISO/TC 213,9599,,[79675],"['en','fr']",28,<p>ISO 25178-603:2013 describes the metrological characteristics of phase-shifting interferometric (PSI) profile and areal surface texture measuring microscopes.</p>

51381,IS,,ISO 25178-604:2013,Geometrical product specifications (GPS) — Surface texture: Areal — Part 604: Nominal characteristics of non-contact (coherence scanning interferometry) instruments,Spécification géométrique des produits (GPS) — État de surface: Surfacique — Partie 604: Caractéristiques nominales des instruments sans contact (à interférométrie par balayage à cohérence),2013-07-24,1,['17.040.20'],ISO/TC 213,9599,,[79676],"['en','fr']",41,<p>ISO 25178-604:2013 specifies the metrological characteristics of coherence scanning interferometry (CSI) systems for 3D mapping of surface height.</p>

53975,IS,,ISO 25178-605:2014,Geometrical product specifications (GPS) — Surface texture: Areal — Part 605: Nominal characteristics of non-contact (point autofocus probe) instruments,Spécification géométrique des produits (GPS) — État de surface: Surfacique — Partie 605: Caractéristiques nominales des instruments sans contact (capteur autofocus à point),2014-01-22,1,['17.040.20'],ISO/TC 213,9599,,[79677],"['en','fr']",31,<p>ISO 25178-605:2014 describes the metrological characteristics of a non-contact instrument for measuring surface texture using point autofocus probing.</p>

59716,IS,,ISO 25178-606:2015,Geometrical product specification (GPS) — Surface texture: Areal — Part 606: Nominal characteristics of non-contact (focus variation) instruments,Spécification géométrique des produits (GPS) — État de surface: Surfacique — Partie 606: Caractéristiques nominales des instruments sans contact (à variation de focale),2015-06-08,1,['17.040.20'],ISO/TC 213,9599,,"[87863,79678]","['en','fr']",27,<p>ISO 25178-606:2015 defines the metrological characteristics of a particular non-contact method measuring surface texture using a focus variation (FV) sensor.</p>

56784,IS,,ISO 25178-71:2012,Geometrical product specifications (GPS) — Surface texture: Areal — Part 71: Software measurement standards,Spécification géométrique des produits (GPS) — État de surface: Surfacique — Partie 71: Étalons logiciels,2012-12-03,1,['17.040.20'],ISO/TC 213,9599,,[65558],"['en','fr']",12,"<p>ISO 25178-71:2012 defines Type S1 and Type S2 software measurement standards (etalons) for verifying the software of measuring instruments. It also defines the file format of Type S1 software measurement standards for the calibration of instruments for the measurement of surface texture by the areal method as defined in the areal surface texture chain of standards, chain link 6.</p>

42787,IS,,ISO 25179:2010,Adhesives — Determination of the solubility of water-soluble or alkali-soluble pressure-sensitive adhesives,"Adhésifs — Détermination de la solubilité des adhésifs sensibles à la pression, solubles dans l'eau ou dans les alcalis",2010-02-15,1,['83.180'],ISO/TC 61/SC 11,9599,,[70310],"['en','fr','ru']",9,<p>ISO 25179:2010 specifies a test method for the determination of the solubility of a water-soluble pressure-sensitive adhesive in water or the solubility of an alkali-soluble pressure-sensitive adhesive in alkali by measuring the loss in mass of the adhesive when immersed in water or alkali. The solubility of the adhesive is one of the key factors in assessing the p

42796,IS,,ISO 25197:2012,"Small craft — Electrical/electronic control systems for steering, shift and throttle","Petits navires — Systèmes électriques/électroniques pour le contrôle de la direction, de l'inverseur et des gaz",2012-12-05,1,['47.080'],ISO/TC 188,9599,,[71354],"['en','fr']",18,"<p>ISO 25197:2012 establishes the requirements for design, construction and testing of electrical/electronic steering, shift and throttle and dynamic position control systems, or combinations thereof, on small craft of up to 24 m length of hull.</p>"

64509,IS,Amd,ISO 25197:2012/Amd 1:2014,"Small craft — Electrical/electronic control systems for steering, shift and throttle — Amendment 1","Petits navires — Systèmes électriques/électroniques pour le contrôle de la direction, de l'inverseur et des gaz — Amendement 1",2014-11-27,1,['47.080'],ISO/TC 188,9599,,[71354],"['en','fr']",1,

21384,IS,,ISO 252-1:1999,Textile conveyor belts — Adhesive strength between constitutive elements — Part 1: Methods of test,Courroies transporteuses à carcasse textile — Adhérence entre éléments constitutifs — Partie 1: Méthodes d'essai,1999-07-29,1,['53.040.20'],ISO/TC 41/SC 3,9599,[4148],[38393],"['en','fr']",8,

45018,IS,Cor,ISO 252-1:1999/Cor 1:2006,Textile conveyor belts — Adhesive strength between constitutive elements — Part 1: Methods of test — Technical Corrigendum 1,Courroies transporteuses à carcasse textile — Adhérence entre éléments constitutifs — Partie 1: Méthodes d'essai — Rectificatif technique 1,2006-11-22,1,['53.040.20'],ISO/TC 41/SC 3,9599,,[38393],"['en','fr']",1,

4147,IS,,ISO 252:1975,Conveyor belts — Minimum requirements for ply adhesion and method of test,Courroies transporteuses — Caractéristiques minimales pour l'adhérence entre éléments constitutifs et méthode d'essai,1975-05-01,1,['53.040.20'],ISO/TC 41,9599,,[4148],"['en','fr']",6,

4148,IS,,ISO 252:1988,Conveyor belts — Ply adhesion between constitutive elements — Test method and requirements,Courroies transporteuses — Adhérence entre éléments constitutifs — Méthodes d'essai et spécifications,1988-04-07,2,['53.040.20'],ISO/TC 41/SC 3,9599,[4147],"[21384,25868]","['en','fr']",7,"<p>This second edition cancels and replaces the first edition (1975). Specifies the adhesion test methods and their minimum values bewtween plies, and between covers and carcase, of conveyor belts. It does not apply to heat- and oil-resistant conveyor belts.</p>"

38393,IS,,ISO 252:2007,Conveyor belts — Adhesion between constitutive elements — Test methods,Courroies transporteuses — Adhérence entre éléments constitutifs — Méthodes d'essai,2007-06-13,3,['53.040.20'],ISO/TC 41/SC 3,9599,"[21384,45018]",[84329],"['en','fr']",7,"<p>ISO 252:2007 specifies two test methods, A and B, for determining the adhesion strength between constitutive elements of a conveyor belt, i.e. between plies and between covers and carcass. Basic test conditions are in conformity with ISO 36.</p><p>It is applicable to all types of construction of conveyor belting with the exception of belts containing steel cord reinforcement, and textile-reinforced belts with a full-thickness t

44056,IS,,ISO 25239-1:2011,Friction stir welding — Aluminium — Part 1: Vocabulary,Soudage par friction-malaxage — Aluminium — Partie 1: Vocabulaire,2011-12-16,1,"['25.160.10','01.040.25']",IIW,9599,,"[77959,69620]","['de','en','fr']",22,"<p>ISO 25239-1:2011 defines friction stir welding terms. In ISO 25239-1:2011, the term 'aluminium' refers to aluminium and its alloys.</p>"

44057,IS,,ISO 25239-2:2011,Friction stir welding — Aluminium — Part 2: Design of weld joints,Soudage par friction-malaxage — Aluminium — Partie 2: Conception des assemblages soudés,2011-12-16,1,"['25.160.10','25.160.40']",IIW,9599,,"[69621,77960]","['en','fr']",5,"<p>ISO 25239-2:2011 specifies design requirements for friction stir weld joints. In ISO 25239-2:2011, the term 'aluminium' refers to aluminium and its alloys.</p><p>ISO 25239-2:2011 does not apply to friction stir spot welding.</p>"

44058,IS,,ISO 25239-3:2011,Friction stir welding — Aluminium — Part 3: Qualification of welding operators,Soudage par friction-malaxage — Aluminium — Partie 3: Qualification des opérateurs soudeurs,2011-12-16,1,"['25.160.10','25.160.01']",IIW,9599,,"[69622,77961]","['en','fr']",12,"<p>ISO 25239:2011 specifies requirements for the qualification of welding operators for the friction stir welding (FSW) of aluminium. In ISO 25239:2011, the term 'aluminium' refers to aluminium and its alloys.</p><p>ISO 25239:2011 does not apply to friction stir spot welding.</p>"