Withdrawn and superseded ISO standards — page 86 of 246

24237,IS,Cor,ISO 2431:1993/Cor 1:1994,Paints and varnishes — Determination of flow time by use of flow cups — Technical Corrigendum 1,Peintures et vernis — Détermination du temps d'écoulement au moyen de coupes d'écoulement — Rectificatif technique 1,1994-06-23,4,['87.040'],ISO/TC 35/SC 9,9599,,[51936],"['en','fr']",2,"<p>Replaces figure 1 by a figure, in which the mouth of the jet is 0,1 mm below the cup body in order to minimize eddy-current effects.</p>"

31911,IS,Cor,ISO 2431:1993/Cor 2:1999,Paints and varnishes — Determination of flow time by use of flow cups — Technical Corrigendum 2,Peintures et vernis — Détermination du temps d'écoulement au moyen de coupes d'écoulement — Rectificatif technique 2,1999-03-25,4,['87.040'],ISO/TC 35/SC 9,9599,,[51936],"['en','fr']",1,

51936,IS,,ISO 2431:2011,Paints and varnishes — Determination of flow time by use of flow cups,Peintures et vernis — Détermination du temps d'écoulement au moyen de coupes d'écoulement,2011-11-10,5,['87.040'],ISO/TC 35/SC 9,9599,"[24237,7341,31911]",[73851],"['en','fr']",15,"<p>ISO 2431:2011 specifies a method for determining the flow time of paints, varnishes and related products that can be used to control consistency.</p><p>Four flow cups of similar dimensions, but having orifice diameters of 3 mm, 4 mm, 5 mm and 6 mm, are specified. Two methods for checking the flow cups for wear and tear are given in an annex.</p><p>Flow cups with a replaceable jet are not covered by ISO 2431 as the clos

37127,IS,,ISO 24314:2006,Structural steels — Structural steels for building with improved seismic resistance — Technical delivery conditions,Aciers de construction — Aciers de construction à résistance améliorée aux séismes — Conditions techniques de livraison,2006-10-06,1,"['77.140.70','91.120.25']",ISO/TC 17/SC 3,9599,,[60902],"['en','ru']",20,"<p>ISO 24314:2006 specifies qualities for seismic-purpose structural steels. This International Standard applies to steel plates with thicknesses of 6 mm or over and up to 125 mm, wide flats and hot-rolled sections, which are used in the as-delivered condition and normally intended for bolted, riveted or welded structures.</p>"

7342,IS,,ISO 2433:1973,Test conditions for external cylindrical grinding machines with a movable table — Testing of accuracy,Conditions d'essais des machines à rectifier les surfaces de révolution extérieures à table mobile — Contrôle de la précision,1973-12-01,1,['25.080.50'],ISO/TC 39,9599,,[7343],"['en','fr']",11,

7343,IS,,ISO 2433:1984,Acceptance conditions for external cylindrical grinding machines with a movable table — Testing of accuracy,Conditions de réception des machines à rectifier les surfaces de révolution extérieures à table mobile — Contrôle de la précision,1984-11-01,2,['25.080.50'],ISO/TC 39/SC 2,9599,[7342],[27414],"['en','fr']",11,

40778,IS,,ISO 24334:2006,Laminate floor coverings — Determination of locking strength for mechanically assembled panels,Revêtements de sol stratifiés — Détermination de la résistance à la traction des lames assemblées mécaniquement,2006-07-26,1,['97.150'],ISO/TC 219,9599,,[65426],['en'],10,"<p>ISO 24334:2006 specifies a method for the determination of the locking strength of joints between laminate floor covering panels, which are assembled with both vertical and horizontal mechanical locking systems.</p>"

65426,IS,,ISO 24334:2014,Laminate floor coverings — Determination of locking strength for mechanically assembled panels,Revêtements de sol stratifiés — Détermination de la résistance à la traction des lames assemblées mécaniquement,2014-11-21,2,['97.150'],ISO/TC 219,9599,[40778],[75637],['en'],7,<p>ISO 24334:2014 specifies a method for the determination of the locking strength of joints between laminate floor covering panels which are assembled with both vertical and horizontal mechanical locking systems.</p>

37130,IS,,ISO 24335:2006,Laminate floor coverings — Determination of impact resistance,Revêtements de sol stratifiés — Détermination de la résistance aux chocs,2006-03-03,1,['97.150'],ISO/TC 219,9599,,[81644],['en'],11,<p>ISO 24335:2006 specifies how to determine the impact resistance of laminate floor covering elements. The test described measures the ability of the surface layer to withstand impact from both small and large objects dropped on the floor covering. The testing is destructive by means of the impact on the surface layer from one small and one larger steel ball simulating different scenarios. The force of the small steel ball and the drop height of the larger steel ball are used

37132,IS,,ISO 24337:2006,Laminate floor coverings — Determination of geometrical characteristics,Revêtements de sol stratifiés — Détermination des caractéristiques géométriques,2006-08-07,1,"['79.080','97.150']",ISO/TC 219,9599,,[74517],"['en','fr']",11,"<p>ISO 24337:2006 gives test methods to determine the dimensional variance between elements of laminate floor coverings in a manufactured free-standing shape (unrestricted) in respect to thickness, length, width, squareness, straightness, width flatness, length flatness, openings between assembled elements and height differences between assembled elements.</p>"

37133,IS,,ISO 24338:2006,Laminate floor coverings — Determination of abrasion resistance,Revêtements de sol stratifiés — Détermination de la résistance à l'abrasion,2006-03-23,1,['97.150'],ISO/TC 219,9599,,[61320],"['en','fr']",10,<p>ISO 24338:2006 specifies a method for measuring abrasion of laminate floor covering elements. The test described measures the ability of the surface layer to resist abrasive wear-through. Abrasion is achieved by rotating a test specimen in contact with a pair of loaded cylindrical wheels covered with specified abrasive paper. The number of revolutions of the test specimen required to cause a defined degree of abrasion is measured.</p>

61320,IS,,ISO 24338:2014,Laminate floor coverings — Determination of abrasion resistance,Revêtements de sol stratifiés — Détermination de la résistance à l'abrasion,2014-12-09,2,['97.150'],ISO/TC 219,9599,[37133],[81219],['en'],20,"<p>ISO 24338:2014 specifies two methods (A and B) for measuring abrasion of laminate floor covering elements. The tests described measure the ability of the surface layer to resist abrasive wear-through.</p><p>Abrasion, according to method A, is achieved by rotating a test specimen in contact with a pair of loaded cylindrical wheels covered with specified abrasive paper. The resistance to wear, according to method B, is evaluated by abrading the face of test piece

40590,IS,,ISO 24342:2006,"Resilient floor-covering tiles — Determination of side length, edge straightness and squareness","Dalles pour revêtements de sol résilients — Détermination de la longueur des bords, de la rectitude des arêtes et de l'équerrage",2006-08-28,1,['97.150'],ISO/TC 219,9599,,[45774],"['en','fr']",10,"<p>ISO 24342:2006 describes methods for determining side lengths, straightness of edges and squareness of resilient floor tiles. </p><p>The side lengths, straightness and squareness of resilient floor tile are important considerations because installed flooring will have an objectionable appearance if these performance criteria are not followed. This may cause the installed ti

45774,IS,,ISO 24342:2007,"Resilient and textile floor-coverings — Determination of side length, edge straightness and squareness of tiles","Revêtements de sol résilients ou textiles — Détermination de la longueur des bords, de la rectitude des arêtes et de l'équerrage des dalles",2007-08-23,2,['97.150'],ISO/TC 219,9599,[40590],[68827],"['en','fr']",10,"<p>ISO 24342:2007 describes methods for determining side lengths, straightness of edges and squareness of resilient or textile floor tiles.</p><p>The side lengths, straightness and squareness of resilient or textile floor tiles are important considerations because installed flooring will have an objectionable appearance if these performance cr

61667,IS,Amd,ISO 24342:2007/Amd 1:2012,"Resilient and textile floor-coverings — Determination of side length, edge straightness and squareness of tiles — Amendment 1","Revêtements de sol résilients ou textiles — Détermination de la longueur des bords, de la rectitude des arêtes et de l'équerrage des dalles — Amendement 1",2012-12-06,2,['97.150'],ISO/TC 219,9599,[22811],[68827],"['en','fr']",1,

68827,IS,,ISO 24342:2018,"Resilient and textile floor-coverings — Determination of side length, edge straightness and squareness of tiles","Revêtements de sol résilients ou textiles — Détermination de la longueur des bords, de la rectitude des arêtes et de l'équerrage des dalles",2018-11-08,3,['97.150'],ISO/TC 219,9599,"[45774,61667]",[84742],"['en','fr']",10,"<p>This document describes methods for determining side lengths, straightness of edges and squareness of resilient or textile floor tiles and planks.</p><p>The side lengths, straightness and squareness of resilient or textile floor tiles and planks are important considerations because installed flooring will have an objectionable appea

51057,IS,,ISO 24343-2:2011,Resilient and laminate floor coverings — Determination of indentation and residual indentation — Part 2: Short-term residual indentation of resilient floor covering,Revêtements de sol résilients et stratifiés — Détermination du poinçonnement et du poinçonnement rémanent — Partie 2: Poinçonnement rémanent de courte durée des revêtements de sol résilients,2011-08-05,1,['97.150'],ISO/TC 219,9599,,[75037],['en'],4,<p>ISO 24343-2:2011 describes a method for determining the short-term indentation and residual indentation produced in a resilient floor covering after the application and removal of a constant load.</p>

51058,IS,,ISO 24343-3:2011,Resilient and laminate floor coverings — Determination of indentation and residual indentation — Part 3: Indentation of resilient semi-flexible/vinyl composition tiles,Revêtements de sol résilients et stratifiés — Détermination du poinçonnement et du poinçonnement rémanent — Partie 3: Poinçonnement de carreaux semi-flexibles/carreaux de composition vinylique résilients,2011-08-05,1,['97.150'],ISO/TC 219,9599,,[75038],['en'],4,<p>ISO 24343-3:2011 describes a method for determining the short-term indentation resistance of resilient semi-flexible/vinyl composition tile (VCT) floor covering after the application of constant load.</p>

36734,IS,,ISO 24347:2005,Agricultural vehicles — Mechanical connections between towed and towing vehicles — Dimensions of ball-type coupling device (80 mm),Véhicules agricoles — Liaisons mécaniques entre véhicules remorqués et véhicules remorqueurs — Dimensions des dispositifs d'attelage de type à boule (80 mm),2005-10-31,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[69296],"['en','fr']",10,"<p>ISO 24347:2005 specifies the dimensions and location of a ball-type coupling device of 80 mm nominal diameter, whose male part fitted to an agricultural towing vehicle and female part fitted to a towed, non-balanced vehicle provides mechanical connection between the two vehicles, where the downwards vertical

61494,IS,,ISO 24362-1:2014,Textiles — Methods for determination of certain aromatic amines derived from azo colorants — Part 1: Detection of the use of certain azo colorants accessible with and without extracting the fibres,Textiles — Méthodes de détermination de certaines amines aromatiques dérivées de colorants azoïques — Partie 1: Détection de l'utilisation de certains colorants azoïques accessibles avec ou sans extraction,2014-01-22,1,['59.060.01'],ISO/TC 38,9599,,[68330],"['en','fr']",25,"<p>ISO 24362-1:2014 describes a procedure to detect the use of certain azo colorants that may not be used in the manufacture or treatment of certain commodities made of textile fibres and that are acce

62441,IS,,ISO 24362-3:2014,"Textiles — Methods for determination of certain aromatic amines derived from azo colorants — Part 3: Detection of the use of certain azo colorants, which may release 4-aminoazobenzene",Textiles — Méthodes de détermination de certaines amines aromatiques dérivées de colorants azoïques — Partie 3: Détection de l'utilisation de certains colorants azoïques susceptibles de libérer du 4-aminoazobenzène,2014-01-22,1,['59.060.01'],ISO/TC 38,9599,,[68331],"['en','fr']",18,"<p>Azo colorants that are able to form 4-aminoazobenzene, generate under the conditions of ISO 24362‑1:2014 the amines aniline and 1,4-phenylenediamine. The presence of these 4-aminoazobenzene colorants

7348,IS,,ISO 2437:1972,Recommended practice for the X-ray inspection of fusion welded butt joints for aluminium and its alloys and magnesium and its alloys 5 to 50 mm thick,Pratiques recommandées pour l'examen aux rayons X des joints bout à bout soudés par fusion sur aluminium et ses alliages et magnésium et ses alliages d'épaisseur comprise entre 5 et 50 mm,1972-10-01,1,['25.160.40'],ISO/TC 44/SC 5,9599,,[7349],"['en','fr']",6,<p>Provides general guidance on the techniques of weld radiography with the object of enabling satisfactory results to be obtained and it enunciates some rules which are based on generally accepted practice and the fundamental theory of the subject. Relates to the exa

42177,IS,,ISO 24373:2008,Welding consumables — Solid wires and rods for fusion welding of copper and copper alloys — Classification,Produits consommables pour le soudage — Fils pleins et baguettes pleines pour le soudage par fusion du cuivre et des alliages de cuivre — Classification,2008-03-04,1,['25.160.20'],ISO/TC 44/SC 3,9599,,[72420],"['en','fr']",10,<p>ISO 24373:2008 specifies requirements for classification of solid wires and rods for fusion welding of copper and copper alloys. The classification of the solid wires and rods is based on their chemical composition.</p>

7351,IS,,ISO 2439:1980,"Polymeric materials, cellular flexible — Determination of hardness (indentation technique)",Matériaux polymères alvéolaires souples — Détermination de la dureté (technique par indentation),1980-11-01,2,['83.100'],ISO/TC 45/SC 4,9599,,[20155],"['en','fr']",3,

20155,IS,,ISO 2439:1997,Flexible cellular polymeric materials — Determination of hardness (indentation technique),Matériaux polymères alvéolaires souples — Détermination de la dureté (technique par indentation),1997-09-11,3,['83.100'],ISO/TC 45/SC 4,9599,[7351],[42717],"['en','fr']",4,

30431,IS,Cor,ISO 2439:1997/Cor 1:1998,Flexible cellular polymeric materials — Determination of hardness (indentation technique) — Technical Corrigendum 1,Matériaux polymères alvéolaires souples — Détermination de la dureté (technique par indentation) — Rectificatif technique 1,1998-06-04,3,['83.100'],ISO/TC 45/SC 4,9599,,[42717],"['en','fr']",1,

42197,IS,,ISO 24394:2008,Welding for aerospace applications — Qualification test for welders and welding operators — Fusion welding of metallic components,Soudage pour applications aérospatiales — Épreuve de qualification pour soudeurs et opérateurs — Soudage par fusion des composants métalliques,2008-10-21,1,['25.160.01'],ISO/TC 44/SC 14,9599,,[70092],"['en','fr']",30,<p>ISO 24394:2008 specifies requirements for the qualification of welders and welding operators for the fusion welding of metallic materials for aerospace applications.</p>

60507,IS,Amd,ISO 24394:2008/Amd 1:2012,Welding for aerospace applications — Qualification test for welders and welding operators — Fusion welding of metallic components — Amendment 1,Soudage pour applications aérospatiales — Épreuve de qualification pour soudeurs et opérateurs — Soudage par fusion des composants métalliques — Amendement 1,2012-11-08,1,['25.160.01'],ISO/TC 44/SC 14,9599,,[70092],['en'],9,

70092,IS,,ISO 24394:2018,Welding for aerospace applications — Qualification test for welders and welding operators — Fusion welding of metallic components,Soudage pour applications aérospatiales — Épreuve de qualification pour soudeurs et opérateurs — Soudage par fusion des composants métalliques,2018-12-13,2,['25.160.01'],ISO/TC 44/SC 14,9599,"[60507,42197]",[83932],"['en','fr']",38,"<p>This document specifies requirements for the qualification of welders and welding operators for the fusion welding of metallic materials for aerospace applications.</p><p>NOTE Success in the test is an essential precondition for the qualification of welders (3.2) and welding operators (3.3) in new prod

7352,IS,,ISO 2440:1983,"Polymeric materials, cellular flexible — Accelerated ageing tests",Matériaux polymères alvéolaires souples — Essais de vieillissement accéléré,1983-12-01,2,['83.100'],ISO/TC 45,9599,,[2298],"['en','fr']",2,

2298,IS,,ISO 2440:1997,Flexible and rigid cellular polymeric materials — Accelerated ageing tests,Matériaux polymères alvéolaires souples et rigides — Essais de vieillissement accéléré,1997-09-11,3,['83.100'],ISO/TC 45/SC 4,9599,[7352],[77359],"['en','fr']",4,

50767,IS,Amd,ISO 2440:1997/Amd 1:2010,Flexible and rigid cellular polymeric materials — Accelerated ageing tests — Amendment 1,Matériaux polymères alvéolaires souples et rigides — Essais de vieillissement accéléré — Amendement 1,2010-02-11,3,['83.100'],ISO/TC 45/SC 4,9599,,[77359],"['en','fr']",2,

63705,IS,Amd,ISO 2440:1997/Amd 2:2014,Flexible and rigid cellular polymeric materials — Accelerated ageing tests — Amendment 2,Matériaux polymères alvéolaires souples et rigides — Essais de vieillissement accéléré — Amendement 2,2014-09-24,3,['83.100'],ISO/TC 45/SC 4,9599,,[77359],"['en','fr']",1,

77359,IS,,ISO 2440:2019,Flexible and rigid cellular polymeric materials — Accelerated ageing tests,Matériaux polymères alvéolaires souples et rigides — Essais de vieillissement accéléré,2019-11-05,4,['83.100'],ISO/TC 45/SC 4,9599,"[63705,50767,2298]",[86333],"['en','fr']",5,"<p>This document specifies, for flexible and rigid cellular polymeric materials, laboratory procedures which are intended to imitate the effects of naturally occurring reactions such as oxidation or hydrolysis by humidity. The physical properties of interest are measured before and after the application of the specified treatments.</p><p>Test conditions are only given for open cellular latex, both open- and closed-cell p

50240,IS,,ISO 24409-1:2010,"Ships and marine technology — Design, location and use of shipboard safety signs, safety-related signs, safety notices and safety markings — Part 1: Design principles","Navires et technologie maritime — Conception, emplacement et utilisation des signaux de sécurité, signaux relatifs à la sécurité, notes de sécurité et marquages de sécurité à bord des navires — Partie 1: Principes de conception",2010-11-16,1,['47.020.01'],ISO/TC 8/SC 1,9599,,[69088],"['en','ru']",21,"<p> ISO 24409-1:2010 prescribes general design principles for shipboard safety and safety-related signs, markings, and notices intended to communicate safety-related information to persons on board shi

7353,IS,,ISO 2441:1975,Pipeline flanges for general use — Shapes and dimensions of pressure-tight surfaces,Brides de tuyauterie pour usage général — Formes et dimensions des surfaces d'étanchéité,1975-11-01,1,['23.040.60'],ISO/TC 5,9599,,"[13573,13574,13575]",['en'],5,

37202,IS,,ISO 24410:2005,Earth-moving machinery — Coupling of attachments to skid steer loaders,Engins de terrassement — Attelage des accessoires des chargeuses à direction articulée,2005-04-22,1,['53.100'],ISO/TC 127/SC 2,9599,,[70043],"['en','fr']",5,"<p>ISO 24410:2005 provides for the interchangeability of attachments on skid steer loaders by establishing dimensional limits for the attachment interface. It is applicable to skid steer loaders whose operating mass according to ISO 6165 is 4 500 kg or less. Narrow skid steer loaders may have a width that does not allow compliance. Its requirements do not restrict the design of the attachment bracket locking system, which is left to the discr

37208,IS,,ISO 24431:2006,Gas cylinders — Cylinders for compressed and liquefied gases (excluding acetylene) — Inspection at time of filling,Bouteilles à gaz — Bouteilles à gaz comprimés et liquéfiés (à l'exception de l'acétylène) — Contrôle au moment du remplissage,2006-09-06,1,['23.020.35'],ISO/TC 58/SC 4,9599,"[19098,18526]",[63063],['en'],11,"<p>ISO 24431:2006 specifies the inspection requirements at the time of filling, and applies to seamless or welded transportable gas cylinders made of steel or aluminium alloy for liquefied or compressed gases (excluding acetylene) of a water capacity of between 0,5 l and 150 l. It also applies to cylinders of less than 0,5 l water capacity, as far as

7355,IS,,ISO 2444:1974,Joints in building — Vocabulary,Joints dans le bâtiment — Vocabulaire,1974-11-01,1,"['91.060.99','01.040.91']",ISO/TC 59,9599,,[7356],"['en','fr']",2,

7356,IS,,ISO 2444:1988,Joints in building — Vocabulary,Joints dans le bâtiment — Vocabulaire,1988-12-15,2,"['91.060.99','01.040.91']",ISO/TC 59/SC 2,9599,[7355],[72244],"['en','fr']",3,"<p>Defines terms used to describe building joints, their constituent parts and their design in building construction. Cancels and replaces the first edition (ISO 2444-1974), of which it constitutes a minor revision.</p>"

46521,IS,,ISO 24442:2011,Cosmetics — Sun protection test methods — In vivo determination of sunscreen UVA protection,Cosmétique — Méthodes d'évaluation de la protection solaire — Détermination in vivo de la protection UVA,2011-12-13,1,['71.100.70'],ISO/TC 217,9599,,[75496],"['en','fr']",26,"<p>ISO 24442:2011 specifies an in vivo method for assessment of the UVA protection factor (UVAPF) of topical sunscreen products. It is applicable to cosmetics, drugs and other products intended to be topically applied to human skin, including any component able to absorb, reflect or scatter UV rays.</p><p>ISO 24442:2011 provides a basis for the evaluation of sunscreen products for the protection of human

46522,IS,,ISO 24443:2012,Determination of sunscreen UVA photoprotection in vitro,Détermination in vitro de la photoprotection UVA,2012-05-30,1,['71.100.70'],ISO/TC 217,9599,,[75059],"['en','fr']",27,"<p>ISO 24443:2012 specifies an <i>in vitro</i> procedure to characterize the UVA protection of sunscreen products. Specifications are given to enable determination of the spectral absorbance characteristics of UVA protection in a reproducible manner. </p><p>In order to determine relevant UVA protection parameters, the method has been created to provide a UV spectral absorbance curve from which a number of calculations and evaluations can be undertaken. This method relies on the use of <i>in vivo

46523,IS,,ISO 24444:2010,Cosmetics — Sun protection test methods — In vivo determination of the sun protection factor (SPF),Cosmétiques — Méthodes d'essai de protection solaire — Détermination in vivo du facteur de protection solaire (FPS),2010-11-04,1,['71.100.70'],ISO/TC 217,9599,,[72250],"['en','fr']",45,"<p>ISO 24444:2010 specifies a method for the <i>in vivo</i> determination of the sun protection factor (SPF) of sunscreen products. This International Standard is applicable to products that contain any component able to absorb, reflect or scatter ultraviolet (UV) rays and which are intended to be placed in contact with human skin.</p><p>ISO 24444:2010 provides a basis for the evaluation

7358,IS,,ISO 2446:1976,Milk — Determination of fat content (Routine method),Lait — Détermination de la teneur en matière grasse (Méthode de routine),1976-10-01,1,['67.100.10'],ISO/TC 34/SC 5,9599,,"[7359,51019]","['en','fr']",7,"<p>Is applicable to liquid milk, whole or partially skimmed, raw or pasteurized. The method specified is based on the saparation of the fat of the milk in a butyrometer by centrifuging after the protein has been dissolved with sulphuric acid. The procedure for checking the capacity of the milk pipette is described in an annex.</p>"

51019,IS,,ISO 2446:2008,Milk — Determination of fat content,Lait — Détermination de la teneur en matière grasse,2008-08-26,2,['67.100.10'],ISO/TC 34/SC 5,9599,[7358],[65935],"['en','fr','ru']",12,"<p>ISO 2446¦IDF 226:2008 specifies a routine method (the Gerber method) for the determination of the fat content of milk and includes guidance on the determination of the appropriate capacity of the milk pipette and on the determination of the corrections to apply to the results if the milk is not of average fat content. The procedure for checking the capacity of the milk pipette is specified in an annex.</p><p>The method is applicable to liquid milk, whole or partially skimmed, raw or pasteurized.

7360,IS,,ISO 2447:1974,Fruit and vegetable products — Determination of tin,Produits dérivés des fruits et légumes — Dosage de l'étain,1974-02-01,1,['67.080.01'],ISO/TC 34/SC 3,9599,,[7361],"['en','fr']",2,

78872,IS,,ISO 24477:2022,"Vacuum technology — Vacuum gauges — Specifications, calibration and measurement uncertainties for spinning rotor gauges","Technique du vide — Manomètres à vide — Spécifications, étalonnage et incertitudes de mesure pour manomètres à rotor",2022-08-05,1,['23.160'],ISO/TC 112,9599,,[87686],['en'],11,"<p>This document defines terms related to spinning rotor gauges (SRGs), specifies the necessary parameters for SRGs, details their calibration procedure and describes which measurement uncertainties to consider when operating these gauges. This document is applicable to pressure up to 2 Pa.</p>"

7362,IS,,ISO 2448:1973,Fruit and vegetable products — Determination of ethanol,Produits dérivés des fruits et légumes — Dosage de l'éthanol,1973-05-01,1,['67.080.01'],ISO/TC 34/SC 3,9599,,[22570],"['en','fr']",3,

78892,IS,,ISO 24487-1:2021,Graphic technology — Processless lithographic plates — Part 1: Evaluation methods for characteristics and performance,Technologie graphique — Plaques lithographiques sans traitement — Partie 1: Méthodes d'évaluation des caractéristiques et des performances,2021-11-12,1,['37.100.10'],ISO/TC 130,9599,,[85606],['en'],29,"<p>This document applies to processless lithographic plates and specifies evaluation methods for lithographic plate characteristics, on-press development performance, usability and print image quality.</p><p>It specifies measurement conditions for materials and equipment and provides guidelines for the selection of suitable processless lithographic pl

37235,IS,,ISO 24490:2005,Cryogenic vessels — Pumps for cryogenic service,Récipients cryogéniques — Pompes pour service cryogénique,2005-04-20,1,['23.020.40'],ISO/TC 220,9599,,[64666],['en'],14,"<p>ISO 24490:2005 specifies the minimum requirements for the design, manufacture and testing of pumps for cryogenic service.</p><p>ISO 24490:2005 is applicable to centrifugal pumps. However the principles may be applied to other types of pump (e.g. reciprocating pumps).</p><p>ISO 24490:2005 also gives guidance on the design of installations.</p><p>It does not specify requirements for operation or maintenance.</p><p>For cryogenic fluids, see ISO 21029-1, ISO 20421-1 and/or ISO 21009-1.</p>"

64666,IS,,ISO 24490:2016,Cryogenic vessels — Pumps for cryogenic service,Récipients cryogéniques — Pompes pour service cryogénique,2016-03-15,2,['23.020.40'],ISO/TC 220,9599,[37235],[85192],"['en','fr']",15,"<p>ISO 24490:2016 specifies the minimum requirements for the design, manufacture and testing of pumps for cryogenic service.</p><p>ISO 24490:2016 is applicable to centrifugal pumps. However, it can be applied to other types of cryogenic pumps (e.g. reciprocating pumps), where applicable.</p><p>This International Standard also gives guidance on the design of installations (see Annex A).</p><p>It does not specify requirements for operation or maintenance.</p><p>NOTE For cryogenic

66835,IS,,ISO 24496:2017,Office furniture — Office chairs — Methods for the determination of dimensions,Mobilier de bureau — Sièges de travail pour bureau — Méthodes pour déterminer les dimensions,2017-03-03,1,['97.140'],ISO/TC 136,9599,[61980],[76831],['en'],65,<p>ISO 24496:2017 specifies methods for the determination of the dimensions of office chairs.</p><p>ISO 24496:2017 does not contain dimensional specifications or requirements.</p>

42265,IS,,ISO 24497-1:2007,Non-destructive testing — Metal magnetic memory — Part 1: Vocabulary,Essais non destructifs — Mémoire magnétique des métaux — Partie 1: Vocabulaire,2007-11-05,1,"['01.040.25','25.160.40']",IIW,9599,,[72146],['en'],4,"<p>ISO 24497-1:2007 specifies terms and definitions for procedures in the sphere of non-destructive testing by the method of metal magnetic memory.</p><p>The terms specified in ISO 24497-1:2007 are mandatory for application in all types of documentation and literature in the sphere of non-destructive testing, using the method of metal magnetic memory included in the scope of standardization works and/or using the results of these works.</p>"

42264,IS,,ISO 24497-2:2007,Non-destructive testing — Metal magnetic memory — Part 2: General requirements,Essais non destructifs — Mémoire magnétique des métaux — Partie 2: Exigences générales,2007-11-05,1,['25.160.40'],IIW,9599,,[72146],['en'],5,"<p>ISO 24497-2:2007 specifies general requirements for the application of the method of metal magnetic memory of components, units, equipment, and structures for various application purposes. It covers non-destructive testing.</p>"

42266,IS,,ISO 24497-3:2007,Non-destructive testing — Metal magnetic memory — Part 3: Inspection of welded joints,Essais non destructifs — Mémoire magnétique des métaux — Partie 3: Examen des assemblages soudés,2007-11-05,1,['25.160.40'],IIW,9599,,"[72147,72148]",['en'],12,"<p>ISO 24497-3:2007 specifies the general requirements for the application of the metal magnetic memory inspection method (MMM inspection) as a non-destructive testing method for quality assurance of welded joints of pressurized components.</p><p>ISO 24497-3:2007 may be applied to welded joints in any type of products, pipelines, vessels, equipment, and metal constructions, as agreed with the purchaser.</p><p>The terms and

4136,IS,,ISO 245:1986,Aircraft — Lockwire,Aéronautique — Fil à freiner,1986-12-04,1,['49.030.50'],ISO/TC 20/SC 4,9599,,[27751],"['en','fr']",1,

7364,IS,,ISO 2450:1972,Cream — Determination of fat content (Reference method),Crème — Détermination de la teneur en matière grasse (Méthode de référence),1972-12-01,1,['67.100.99'],ISO/TC 34/SC 5,9599,,[7365],"['en','fr']",3,

7365,IS,,ISO 2450:1985,Cream — Determination of fat content — Gravimetric method (Reference method),Crème — Détermination de la teneur en matière grasse — Méthode gravimétrique (Méthode de référence),1985-12-19,2,['67.100.99'],ISO/TC 34/SC 5,9599,[7364],[26546],"['en','fr']",8,

26546,IS,,ISO 2450:1999,Cream — Determination of fat content — Gravimetric method (Reference method),Crème — Détermination de la teneur en matière grasse — Méthode gravimétrique (Méthode de référence),1999-09-23,3,['67.100.99'],ISO/TC 34/SC 5,9599,[7365],[51013],"['en','fr']",14,

51013,IS,,ISO 2450:2008,Cream — Determination of fat content — Gravimetric method (Reference method),Crème — Détermination de la teneur en matière grasse — Méthode gravimétrique (Méthode de référence),2008-10-02,4,['67.100.99'],ISO/TC 34/SC 5,9599,[26546],[75226],"['en','fr']",14,"<p>ISO 2450|IDF 16:2008 specifies the reference method for the determination of the fat content of raw, processed and sour cream in which no appreciable separation or breakdown of fat, due to lipolysis, has occurred.</p><p>The method is not applicable to sour creams with starch or other thickening agents.</p>"

63752,IS,,ISO 24505:2016,Ergonomics — Accessible design — Method for creating colour combinations taking account of age-related changes in human colour vision,Ergonomie — Conception accessible — Méthode de création de combinaisons de couleurs tenant compte des changements liés à l'âge dans la vision en couleurs humaine,2016-04-01,1,['13.180'],ISO/TC 159/SC 5,9599,,"[79395,88605]","['en','fr']",25,"<p>ISO 24505:2016 provides a method for creating conspicuous colour combinations for use in visual signs and displays taking into account viewer age. It is based on the perceived similarity of colours at photopic and mesopic lighting conditions.</p><p>ISO 24505:2016 applies to the design of visual

7366,IS,,ISO 2451:1973,Cocoa beans — Specification,Fèves de cacao — Spécifications,1973-12-01,1,['67.140.30'],ISO/TC 34,9599,,"[7367,56534]","['en','fr']",3,"<p>Definitions of relevant terms. Then are specified the preparation, general requirements, grade standards, sampling, methods of test, packing and marking. Recommendations relating to storage and disinfection are given in annexes A and B respectively.</p>"

56534,IS,,ISO 2451:2014,Cocoa beans — Specification,Fèves de cacao — Spécifications,2014-10-20,2,['67.140.30'],ISO/TC 34/SC 18,9599,[7366],[68202],['en'],11,"<p>ISO 2451:2014 specifies the requirements, classification, test methods, sampling, packaging, and marking for cocoa beans.</p><p>Recommendations relating to storage and disinfestation are given as a guide in annexes.</p>"

37246,IS,,ISO 24510:2007,Activities relating to drinking water and wastewater services — Guidelines for the assessment and for the improvement of the service to users,Activités relatives aux services de l'eau potable et de l'assainissement — Lignes directrices pour l'évaluation et l'amélioration du service aux usagers,2007-11-29,1,"['13.060.20','13.060.30','03.080.30']",ISO/TC 224,9599,,[81484],"['en','es','fr']",62,<p>ISO 24510:2007 specifies the elements of drinking water and wastewater services of relevance and interest to users. It also provides guidance on how to identify users' needs and expectations and how to assess whether they are being met.</p><p>The following are within the scope

37247,IS,,ISO 24511:2007,Activities relating to drinking water and wastewater services — Guidelines for the management of wastewater utilities and for the assessment of wastewater services,Activités relatives aux services de l'eau potable et de l'assainissement — Lignes directrices pour le management des services publics de l'assainissement et pour l'évaluation des services fournis,2007-11-29,1,"['93.030','13.060.30']",ISO/TC 224,9599,,[82489],"['en','es','fr']",59,"<p>ISO 24511:2007 provides guidelines for the management of wastewater utilities and for the assessment of wastewater services.</p><p>ISO 24511:2007 is applicable to publicly and privately owned and operated wastewater utilities,

37248,IS,,ISO 24512:2007,Activities relating to drinking water and wastewater services — Guidelines for the management of drinking water utilities and for the assessment of drinking water services,Activités relatives aux services de l'eau potable et de l'assainissement — Lignes directrices pour le management des services publics de l'eau potable et pour l'évaluation des services fournis,2007-11-29,1,"['13.060.20','93.025']",ISO/TC 224,9599,,[82490],"['en','es','fr']",54,"<p>ISO 24512:2007 provides guidelines for the management of drinking water utilities and for the assessment of drinking water services.</p><p>ISO 24512:2007 is applicable to publicly and privately owned and operated water ut

64679,IS,,ISO 24521:2016,Activities relating to drinking water and wastewater services — Guidelines for the management of basic on-site domestic wastewater services,Activités relatives aux services de l'eau potable et des eaux usées — Lignes directrices pour la gestion sur site des services d'eaux usées domestiques de base,2016-08-26,1,"['13.060.30','03.080.30']",ISO/TC 224,9599,,[85440],"['en','fr']",56,"<p>ISO 24521:2016 provides guidance for the management of basic on-site domestic wastewater services, using appropriate technologies in their entirety at any level of development.</p><p>ISO 24521:2016 supplements and is intended to be used in conjunction with ISO 24511. It includes the foll

7368,IS,,ISO 2453:1975,Styrene-butadiene copolymers — Determination of bound styrene content,Copolymères butadiène-styrène — Dosage du styrène lié,1975-02-01,1,['83.040.10'],ISO/TC 45,9599,,[7369],"['en','fr']",4,

7369,IS,,ISO 2453:1991,"Rubber, raw styrene-butadiene, emulsion-polymerized — Determination of bound styrene content — Refractive index method",Caoutchouc butadiène-styrène brut polymérisé en émulsion — Détermination de la teneur en styrène lié — Méthode par l'indice de réfraction,1991-06-27,2,['83.040.10'],ISO/TC 45/SC 3,9599,[7368],[72854],"['en','fr']",6,

38907,IS,Cor,ISO 2453:1991/Cor 1:2003,"Rubber, raw styrene-butadiene, emulsion-polymerized — Determination of bound styrene content — Refractive index method — Technical Corrigendum 1",Caoutchouc butadiène-styrène brut polymérisé en émulsion — Détermination de la teneur en styrène lié — Méthode par l'indice de réfraction — Rectificatif technique 1,2003-09-01,2,['83.040.10'],ISO/TC 45/SC 3,9599,,[72854],"['en','fr']",1,

37503,IS,,ISO 24531:2007,"Intelligent transport systems — System architecture, taxonomy and terminology — Using XML in ITS standards, data registries and data dictionaries","Systèmes intelligents de transport — Architecture, taxinomie et terminologie des systèmes — Usage de XML dans les normes, registres de données et dictionnaires de données, en ITS",2007-06-19,1,['35.240.60'],ISO/TC 204,9599,,[57392],['en'],60,"<p>ISO 24531:2007 has been developed to assist developers and users of intelligent transport systems (ITS) standards who wish to use extensible markup language (XML), by providing a consistent definition of the rules and rule references for the use of XML within intelligent transpor

51851,IS,,ISO 24534-3:2010,Automatic vehicle and equipment identification — Electronic registration identification (ERI) for vehicles — Part 3: Vehicle data,Identification automatique des véhicules et des équipements — Identification d'enregistrement électronique (ERI) pour les véhicules — Partie 3: Données du véhicule,2010-07-14,1,"['35.240.60','03.220.20']",ISO/TC 204,9599,[41698],[59306],"['en','fr']",32,"<p>ISO 24534-3:2010 provides requirements for electronic registration identification (ERI) that are based on an identifier assigned to a vehicle (e.g. for recognition by national authorities) suitable to be used for:</p><ul><li>electronic identification of local and foreign vehicles by n

7370,IS,,ISO 2454:1982,Rubber products — Determination of zinc content — EDTA titrimetric method,Produits en caoutchouc — Détermination de la teneur en zinc — Méthode titrimétrique à l'EDTA,1982-12-01,2,['83.060'],ISO/TC 45,9599,,[2150],"['en','fr']",3,

2150,IS,,ISO 2454:1995,Rubber products — Determination of zinc content — EDTA titrimetric method,Produits en caoutchouc — Dosage du zinc — Méthode titrimétrique à l'EDTA,1995-03-30,3,['83.060'],ISO/TC 45/SC 2,9599,[7370],[43681],"['en','fr']",4,"<p>Cancels and replaces the second edition (1982). Specifies a titrimetric method using ethylenedinitrilotetraacetic acid (EDTA) disodium salt for the determination of the zinc content of all rubber products. The presence of lead, magnesium, iron, titanium, antimony, silica and silicates in the ash does not interfere with the determination. Not applicable, if cobalt is present.</p>"

42281,IS,,ISO 24557:2009,Pulses — Determination of moisture content — Air-oven method,Légumineuses — Détermination de la teneur en eau — Méthode par séchage à l'étuve,2009-09-24,1,['67.060'],ISO/TC 34/SC 4,9599,,[82590],"['en','fr']",8,"<p>ISO 24557:2009 specifies a routine reference method for the determination of moisture content of pulses. The procedure is applicable to chickpeas, lentils, peas, and all classes of beans with the exception of soybeans.</p>"

7372,IS,,ISO 2457:1976,Solid wood parquet — Classification of beech strips,Parquet en bois massif — Classement des lames en hêtre,1976-06-01,2,['79.080'],ISO/TC 218,9599,,[80116],"['en','fr']",3,"<p>Divides non-assembled strips into two quality grades that are identified by (+++) and (++) corresponding to the conditions specified in the tables. The regulations for manufacture, characteristics and delivery conditions are fixed by ISO 1072. Replaces the first edition from 1972.</p>"

42326,IS,,ISO 24598:2007,"Welding consumables — Solid wire electrodes, tubular cored electrodes and electrode/flux combinations for submerged arc welding of creep-resisting steels — Classification","Produits consommables pour le soudage — Fils-électrodes pleins, fils-électrodes fourrés et couples fil-flux pour le soudage à l'arc sous flux des aciers résistant au fluage — Classification",2007-11-12,1,['25.160.20'],ISO/TC 44/SC 3,9599,,[57187],"['en','fr']",17,"<p>ISO 24598:2007 specifies requirements for classification of solid wire electrodes, tubular cored electrodes and electrode/flux combinations (all-weld metal deposits) for submerged arc welding of creep-resisting and low-alloy elevated

57187,IS,,ISO 24598:2012,"Welding consumables — Solid wire electrodes, tubular cored electrodes and electrode-flux combinations for submerged arc welding of creep-resisting steels — Classification","Produits consommables pour le soudage — Fils-électrodes pleins, fils-électrodes fourrés et couples électrodes-flux pour le soudage à l'arc sous flux des aciers résistant au fluage — Classification",2012-05-02,2,['25.160.20'],ISO/TC 44/SC 3,9599,[42326],[73878],"['en','fr']",17,"<p>ISO 24598:2012 specifies requirements for classification of solid wire electrodes, tubular cored electrodes and electrode/flux combinations (all-weld metal deposits) for submerged arc welding of creep resisting and low-

4137,IS,,ISO 246:1978,Cylindrical roller bearings — Separate thrust collars — Boundary dimensions,Roulements à rouleaux cylindrique — Bagues d'épaulement séparées — Dimensions d'encombrement,1978-05-01,1,['21.100.20'],ISO/TC 4,9599,,[20512],"['en','fr']",1,

20512,IS,,ISO 246:1995,"Rolling bearings — Cylindrical roller bearings, separate thrust collars — Boundary dimensions","Roulements — Roulements à rouleaux cylindriques, bagues d'épaulement séparées — Dimensions d'encombrement",1995-05-18,2,['21.100.20'],ISO/TC 4,9599,[4137],[44032],"['en','fr']",3,"<p>Cancels and replaces the first edition (1978). Specifies the width, the maximum outside diameter, the bore and the bore minimum chamfer of separate thrust collars for cylindrical roller bearings in diameter series 2, 3 and 4 as specified in ISO 15.</p>"

51934,IS,,ISO 24611:2012,Language resource management — Morpho-syntactic annotation framework (MAF),Gestion des ressources langagières — Cadre d'annotation morphosyntaxique (MAF),2012-10-19,1,['01.020'],ISO/TC 37/SC 4,9599,,"[85152,79088,85153]","['en','fr','ru']",58,"<p>ISO 24611:2012 provides a framework for the representation of annotations of word-forms in texts; such annotations concern tokens, their relationship with lexical units, and their morpho-syntactic properties.It describes a metamodel for morpho-syntactic annotation that relates to a reference to the data categories contained in the ISOCat data category registry (DCR, as defined in ISO 12620). It also describes an XML serializ

68516,IS,,ISO 24613-1:2019,Language resource management — Lexical markup framework (LMF) — Part 1: Core model,Gestion des ressources linguistiques — Cadre de balisage lexical (LMF) — Partie 1: Modèle de base,2019-06-20,1,"['35.240.30','01.020']",ISO/TC 37/SC 4,9599,[37327],[82014],['en'],13,"<p>This document describes the core model of the lexical markup framework (LMF)l, a metamodel for representing data in monolingual and multilingual lexical databases used with computer applications.</p><p>LMF provides mechanisms that allow the development and integration of a variety of electronic lexical resource types.</p>"

37327,IS,,ISO 24613:2008,Language resource management - Lexical markup framework (LMF),Gestion de ressources langagières — Cadre de balisage lexical,2008-11-17,1,['01.020'],ISO/TC 37/SC 4,9599,,"[75407,75411,68516,72099,75410,74579]",['en'],77,"<p>ISO 24613:2008 describes the Lexical Markup Framework (LMF), a metamodel for representing data in lexical databases used with monolingual and multilingual computer applications. </p><p>LMF provides mechanisms that allow the development and integration of a variety of electronic lexical resource types. These mechanisms will present existing lexicons as far as possible. If this is impossible, problematic information will be identified and isolated.</

37329,IS,,ISO 24615:2010,Language resource management — Syntactic annotation framework (SynAF),Gestion de ressources langagières — Cadre d'annotation syntaxique (SynAF),2010-10-19,1,['01.020'],ISO/TC 37/SC 4,9599,,[62508],['en'],18,"<p>ISO 24615:2010 describes the syntactic annotation framework (SynAF), a high level model for representing the syntactic annotation of linguistic data, with the objective of supporting interoperability across language resources or language processing components. ISO 24615:2010 is complementary and closely related to ISO 24611 (MAF, morpho-syntactic annotation framework) and provides a metamodel for syntactic representations as well as reference data categories f

51967,IS,,ISO 24617-2:2012,Language resource management — Semantic annotation framework (SemAF) — Part 2: Dialogue acts,Gestion des ressources langagières — Cadre d'annotation sémantique (SemAF) — Partie 2: Actes de dialogue,2012-09-04,1,['01.020'],ISO/TC 37/SC 4,9599,,[76443],['en'],104,"<p>ISO 24617-2:2012 provides a set of empirically and theoretically well-motivated concepts for dialogue annotation, a formal language for expressing dialogue annotations -- the dialogue act markup language (DiAML) -- and a method for segmenting a dialogue into semantic units. This allows the manual or automatic annotation of dialogue segments with information about the communicative actions which the parti

60779,IS,,ISO 24617-7:2014,Language resource management — Semantic annotation framework — Part 7: Spatial information (ISOspace),Gestion des ressources linguistiques — Cadre d'annotation sémantique — Partie 7: Information spatiale (ISOspace),2014-12-16,1,['01.020'],ISO/TC 37/SC 4,9599,,[76442],['en'],55,"<p>ISO 24617-7:2014 provides a framework for encoding a broad range not only of spatial information, but also of spatiotemporal information relating to motion as expressed in natural language texts. It includes references to locations, general spatial entities, spatial relations (involving topological, orientational, and metric values), dimensional information, motion events, and paths.</p>"

7377,IS,,ISO 2463:1973,Sodium chlorate for industrial use — Determination of chloride content — Mercurimetric method,Chlorate de sodium à usage industriel — Dosage des chlorures — Méthode mercurimétrique,1973-04-01,1,['71.060.50'],ISO/TC 47,9599,,[1735],"['en','fr']",2,"<p>The method is applicable to products with a content greater than 0,01 % (m/m). It is not applicable to the analysis of mixtures of products such as herbicides and insecticides. The principle consists in titration of the chloride ions with mercury(II) nitrate in the presence of diphenylcarbazone as indicator.</p>"

42336,IS,,ISO 24631-1:2009,Radiofrequency identification of animals — Part 1: Evaluation of conformance of RFID transponders with ISO 11784 and ISO 11785 (including granting and use of a manufacturer code),Identification des animaux par radiofréquence — Partie 1: Évaluation de la conformité des transpondeurs RFID à l'ISO 11784 et à l'ISO 11785 (y compris l'attribution et l'utilisation d'un code de fabricant),2009-08-21,1,['65.040.99'],ISO/TC 23/SC 19,9599,,[63394],"['en','fr']",13,<p>ISO 24631-1:2009 provides the means of evaluating the conformance with ISO 11784 and ISO 11785 of RFID (radiofrequency identification) transponders used in the individual identification of animals. It sets forth

63394,IS,,ISO 24631-1:2017,Radiofrequency identification of animals — Part 1: Evaluation of conformance of RFID transponders with ISO 11784 and ISO 11785 (including granting and use of a manufacturer code),Identification des animaux par radiofréquence — Partie 1: Évaluation de la conformité des transpondeurs RFID à l'ISO 11784 et à l'ISO 11785 (y compris l'attribution et l'utilisation d'un code de fabricant),2017-09-15,2,['65.040.99'],ISO/TC 23/SC 19,9599,[42336],[88788],"['en','fr']",15,"<p>ISO 24631-1:2017 provides the means of evaluating the conformance with ISO 11784 and ISO 11785 of radiofrequency identification (RFID) transponders used in the individual identification of animals. It se

42337,IS,,ISO 24631-2:2009,Radiofrequency identification of animals — Part 2: Evaluation of conformance of RFID transceivers with ISO 11784 and ISO 11785,Identification des animaux par radiofréquence — Partie 2: Évaluation de la conformité des émetteurs-récepteurs RFID à l'ISO 11784 et à l'ISO 11785,2009-08-21,1,['65.040.99'],ISO/TC 23/SC 19,9599,,[63395],"['en','fr']",12,<p>ISO 24631-2:2009 provides the means of evaluating the conformance with ISO 11784 and ISO 11785 of RFID (radiofrequency identification) transceivers used in the individual identification of animals. It also specifies the procedure for applying for a transceiver test approval and the associated rights and obligations of th

42338,IS,,ISO 24631-3:2009,Radiofrequency identification of animals — Part 3: Evaluation of performance of RFID transponders conforming with ISO 11784 and ISO 11785,Identification des animaux par radiofréquence — Partie 3: Évaluation de la performance des transpondeurs RFID conformes à l'ISO 11784 et à l'ISO 11785,2009-08-21,1,['65.040.99'],ISO/TC 23/SC 19,9599,,[63396],"['en','fr']",28,<p>ISO 24631-3:2009 provides the means of evaluating the performance of ISO 11784- and ISO 11785‑conformant RFID (radiofrequency identification) transponders used in the individual identification of animals. </p>

63396,IS,,ISO 24631-3:2017,Radiofrequency identification of animals — Part 3: Evaluation of performance of RFID transponders conforming with ISO 11784 and ISO 11785,Identification des animaux par radiofréquence — Partie 3: Évaluation de la performance des transpondeurs RFID conformes à l'ISO 11784 et à l'ISO 11785,2017-09-15,2,['65.040.99'],ISO/TC 23/SC 19,9599,[42338],[89327],"['en','fr']",28,<p>ISO 24631-3:2017 provides the means of evaluating the performance of ISO 11784- and ISO 11785-conformant radiofrequency identification (RFID) transponders used in the individual identification of animals.</p><p>The test procedures specified in this document are recognized by the Federation of Europe

42339,IS,,ISO 24631-4:2009,Radiofrequency identification of animals — Part 4: Evaluation of performance of RFID transceivers conforming with ISO 11784 and ISO 11785,Identification des animaux par radiofréquence — Partie 4: Évaluation de la performance des émetteurs-récepteurs RFID conformes à l'ISO 11784 et à l'ISO 11785,2009-08-21,1,['65.040.99'],ISO/TC 23/SC 19,9599,,[63397],"['en','fr']",15,<p>ISO 24631-4:2009 provides the means of evaluating the performance of ISO 11784- and ISO 11785‑conformant RFID (radiofrequency identification) transceivers used in the individual identification of animals. </p>

42345,IS,,ISO 24638:2008,Space systems — Pressure components and pressure system integration,Systèmes spatiaux — Intégration des composants sous pression et des systèmes sous pression,2008-11-05,1,['49.140'],ISO/TC 20/SC 14,9599,,[74188],['en'],25,"<p>ISO 24638:2008 establishes the baseline requirements for the design, fabrication and testing of space flight pressure components. It also establishes the requirements for assembly, installation, test, inspection, operation and maintenance of the pressure systems in spacecraft and launch vehicles. These requirements, when implemented on a particular space system, ensure a high level of confidence in achieving safe and reliable operation.</p><p>I

7382,IS,,ISO 2467:1980,Cinematography — Image area produced by 65 and 70 mm motion-picture camera aperture and maximum projectable image area on 70 mm motion-picture prints — Positions and dimensions,Cinématographie — Champ d'image enregistré par la fenêtre des caméras 65 et 70 mm et champ maximal d'image projetable sur copies d'exploitation 70 mm — Positions et dimensions,1980-07-01,2,['37.060.20'],ISO/TC 36,9599,,"[40001,34906]","['en','fr']",3,

7383,IS,,ISO 2469:1977,"Paper, board and pulps — Measurement of diffuse reflectance factor","Papier, carton et pâtes — Mesurage du facteur de réflectance diffuse",1977-02-01,2,"['85.060','85.040']",ISO/TC 6,9599,,[1682],"['en','fr']",7,

1682,IS,,ISO 2469:1994,"Paper, board and pulps — Measurement of diffuse reflectance factor","Papier, carton et pâtes — Mesurage du facteur de réflectance diffuse",1994-11-17,3,"['85.060','85.040']",ISO/TC 6,9599,[7383],"[41960,33828]","['en','fr']",7,"<p>Cancels and replaces the second edition (1977). Specifies the equipment for measuring the diffuse reflectance factor of pulp, paper and board and the procedures for calibrating that equipment. Measurements are used for the evaluation of optical properties such as diffuse blue reflectance factor, the scattering coefficient of pulp, opacity, whiteness, luminous reflectance factor, the chromaticity coordinates of paper and the intrinsic reflect

30379,IS,Cor,ISO 2469:1994/Cor 1:1998,"Paper, board and pulps — Measurement of diffuse reflectance factor — Technical Corrigendum 1","Papier, carton et pâtes — Mesurage du facteur de réflectance diffuse — Rectificatif technique 1",1998-07-09,3,"['85.060','85.040']",ISO/TC 6,9599,,"[41960,33828]","['en','fr']",1,

41960,IS,,ISO 2469:2007,"Paper, board and pulps — Measurement of diffuse radiance factor","Papier, carton et pâtes — Mesurage du facteur de luminance énergétique diffuse",2007-06-11,4,"['85.060','85.040']",ISO/TC 6,9599,"[1682,30379]",[51631],"['en','fr','ru']",19,"<p>ISO 2469:2007 describes the general procedure for measuring the diffuse radiance factor of all types of pulp, paper and board. More particularly, it specifies in detail in Annex A the characteristics of the equipment to be used for such measurements, and in Annex B the procedures to be used for calibrating that equipment.</p><p>ISO 2469:2007 may be used to measure the radiance factors and related properties of materials contain

51631,IS,,ISO 2469:2014,"Paper, board and pulps — Measurement of diffuse radiance factor (diffuse reflectance factor)","Papier, carton et pâtes — Mesurage du facteur de luminance énergétique diffuse (facteur de réflectance diffuse)",2014-07-30,5,"['85.060','85.040']",ISO/TC 6,9599,[41960],[81655],"['en','fr']",19,"<p>ISO 2469:2014 describes the general procedure for measuring the diffuse radiance factor of all types of pulp, paper and board. More particularly, it specifies in detail the characteristics of the equipment to be used for such measurements, and the procedures to be used for calibrating that equipment.</p><p>ISO 2469:2014 may be used to measure the diffuse radiance factors and rel