Withdrawn and superseded ISO standards — page 83 of 246

7154,IS,,ISO 2332:1993,Agricultural tractors and machinery — Connection of implements via three-point linkage — Clearance zone around implement,Tracteurs et matériels agricoles — Liaisons des instruments par l'attelage trois points — Zone de dégagement autour de l'instrument,1993-10-14,2,['65.060.01'],ISO/TC 23/SC 4,9599,[7167],[42847],"['en','fr']",6,"<p>Specifies dimensions. Applies to tractors of categories 1 to 3 and to the connection of agricultural implements to three-point linkages complying with ISO 730-1; also applies where implement couplers, complying with ISO 11001-1, ISO 11001-2 and ISO 11001-3, are used.</p>"

41460,IS,,ISO 23337:2007,"Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using the Improved Lambourn test machine",Caoutchouc vulcanisé ou thermoplastique — Détermination de la résistance à l'abrasion à l'aide d'une machine de Lambourn perfectionnée,2007-07-23,1,['83.060'],ISO/TC 45/SC 2,9599,,[70330],"['en','fr']",11,"<p>ISO 23337:2007 specifies a method for the determination of the resistance of rubber to abrasion using the Improved Lambourn test machine.</p><p>The abrasion loss resulting from the slip caused by the difference in circumferential speed between a disc-shaped rubber test piece and an abrasive wheel, which are driven to rotate independently with the

70330,IS,,ISO 23337:2016,"Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using the Improved Lambourn test machine",Caoutchouc vulcanisé ou thermoplastique — Détermination de la résistance à l'abrasion à l'aide d'une machine de Lambourn perfectionnée,2016-10-27,2,['83.060'],ISO/TC 45/SC 2,9599,[41460],[84124],"['en','fr']",12,"<p>ISO 23337:2016 specifies a method for the determination of the resistance of rubber to abrasion using the Improved Lambourn test machine.</p><p>The abrasion loss resulting from the slip caused by the difference in circumferential speed between a disc-shaped rubber test piece and an abrasive wheel, which are driven to rotate independently w

55368,IS,,ISO 23339:2010,Space systems — Unmanned spacecraft — Estimating the mass of remaining usable propellant,Systèmes spatiaux — Véhicules spatiaux non habités — Estimation de la masse d'ergols résiduels utilisable,2010-11-24,1,['49.140'],ISO/TC 20/SC 14,9599,,[75221],['en'],7,"<p>ISO 23339:2010 gives requirements for estimating the mass of the remaining usable propellant of an unmanned spacecraft in low Earth orbit (LEO) or geostationary Earth orbit (GEO), and for designing propellant measurement systems. It is applicable to spacecraft with either mono- or bi-propellant propulsion systems using liquid or gaseous chemical propellants, and is limited to such systems because they are the

25063,IS,,ISO 2336-2:1996,Hacksaw blades — Part 2: Dimensions for machine blades,Lames de scies droites à métaux — Partie 2: Dimensions des lames à machine,1996-04-18,1,['25.100.40'],ISO/TC 29,9599,,[40606],"['en','fr']",2,"<p>Specifies the dimensions of machine hacksaw blades. It is valid for single edge blades of length from 300 mm up to 700 mm, the tooth pitch of which is no greater than 8,5 mm.</p>"

68546,IS,,ISO 23369:2021,Hydraulic fluid power — Multi-pass method of evaluating filtration performance of a filter element under cyclic flow conditions,Transmissions hydrauliques — Évaluation des performances d’un élément filtrant par la méthode de filtration multi-passe sous débit cyclique,2021-06-16,1,['23.100.60'],ISO/TC 131/SC 6,9599,,[84020],"['en','fr']",34,"<p>This document specifies:</p><p>a) A multi-pass filtration performance test under cyclic flow conditions with continuous contaminant injection for hydraulic fluid power filter elements.</p><p>b) A procedure for determining the contaminant capacity, particulate removal and differential pressure characteristics.</p><p>c) A test cu

7171,IS,,ISO 2338:1972,"Parallel pins, unhardened — Metric series",Goupilles cylindriques non trempées — Série métrique,1972-04-01,1,['21.060.50'],ISO/TC 2,9599,,"[20001,7172]","['en','fr']",2,

7172,IS,,ISO 2338:1986,"Parallel pins, unhardened",Goupilles cylindriques non trempées,1986-10-30,2,['21.060.50'],ISO/TC 2,9599,[7171],[20001],"['en','fr']",3,

41486,IS,,ISO 23380:2008,Selection of methods for the determination of trace elements in coal,Sélection des méthodes de détermination des éléments en traces dans le charbon,2008-10-02,1,['73.040'],ISO/TC 27/SC 5,9599,,[63443],['en'],9,"<p>ISO 23380:2008 provides guidance on the selection of methods used for the determination of trace elements in coal and coal ash. The trace elements of environmental interest include arsenic, beryllium, boron, cadmium, chlorine, chromium, cobalt, copper, fluorine, lead, manganese, mercury, molybdenum, nickel, selenium, vanadium and zinc. To this list can be added the radioactive trace elements, thorium and uranium.</p><p>ISO 23380:2008 does not prescribe the

63443,IS,,ISO 23380:2013,Selection of methods for the determination of trace elements in coal,Sélection des méthodes de détermination des éléments en traces dans le charbon,2013-09-02,2,['73.040'],ISO/TC 27/SC 5,9599,[41486],[79745],"['en','ru']",9,"<p>ISO 23380:2013 provides guidance on the selection of methods used for the determination of trace elements in coal. The trace elements of environmental interest include antimony, arsenic, beryllium, boron, cadmium, chlorine, chromium, cobalt, copper, fluorine, lead, manganese, mercury, molybdenum, nickel, selenium, thallium, vanadium, and zinc. The radioactive trace elements thorium and uranium can be added to this list.</p>"

75403,IS,,ISO 23387:2020,Building information modelling (BIM) — Data templates for construction objects used in the life cycle of built assets — Concepts and principles,Modélisation des informations de la construction (BIM) — Modèles de données pour les objets de construction utilisés durant le cycle de vie des biens construits — Concepts et principes,2020-07-06,1,"['35.240.67','91.010.01']",ISO/TC 59/SC 13,9599,,[85391],"['en','fr']",17,"<p>This document sets out the principles and structure for data templates for construction objects. It is developed to support digital processes using machine-readable formats using a standard data structure to exchange information about any type of constru

7173,IS,,ISO 2339:1974,"Taper pins, unhardened — Metric series",Goupilles coniques non trempées — Série métrique,1974-10-01,1,['21.060.50'],ISO/TC 2,9599,,[7174],"['en','fr']",2,

4119,IS,,ISO 234:1975,Withdrawal of ISO 234-1975,Annulation de l'ISO 234-1975,1975-03-01,1,['25.100.60'],ISO/TC 29,9599,,[4120],['en'],5,

7175,IS,,ISO 2340:1972,Clevis pins — Metric series,Axes d'articulation — Série métrique,1972-04-01,1,['21.060.50'],ISO/TC 2,9599,,[7176],"['en','fr']",2,

75435,IS,,ISO 23402-1:2020,Dentistry — Portable dental equipment for use in non‐permanent healthcare environment — Part 1: General requirements,Médecine bucco-dentaire — Matériel dentaire portatif utilisable dans des environnements de soins de santé non permanents — Partie 1: Exigences générales,2020-09-23,1,['11.060.20'],ISO/TC 106/SC 6,9599,,[89243],"['en','fr']",10,"<p>This document specifies general requirements and test methods for portable dental equipment for use in non-permanent healthcare environments.</p><p>Portable dental equipment within the scope of this document includes portable dental units, portable patient chairs, portable operator's stools, portable operating lights, porta

7177,IS,,ISO 2341:1972,Clevis pins with heads — Metric series,Axes d'articulation avec tête — Série métrique,1972-04-01,1,['21.060.50'],ISO/TC 2,9599,,[7178],"['en','fr']",2,

7179,IS,,ISO 2342:1972,Slotted headless screws — Metric series,"Vis sans tête, fendues — Série métrique",1972-04-01,1,['21.060.10'],ISO/TC 2,9599,,"[29660,36429]","['en','fr']",1,"<p>Specifies the dimensions for diameters from 1 mm up to and including 10 mm; refers to ISO/R 888 for length, and to ISO/R 262 for thread series; for the different shapes and dimensions of screw ends no reference has been made.</p>"

7180,IS,,ISO 2343:1972,Hexagon socket set screws — Metric series,"Vis sans tête, à six pans creux — Série métrique",1972-04-01,1,['21.060.50'],ISO/TC 2,9599,,"[9717,9715,9719,9713]","['en','fr']",1,

7181,IS,,ISO 2344:1981,"Road vehicles — Spark plugs M 14 x 1,25 with conical seating and their cylinder head housing","Véhicules routiers — Bougies d'allumage M 14 x 1,25 à siège conique et leur logement dans la culasse",1981-05-01,4,['43.060.50'],ISO/TC 22,9599,,"[7182,7183]","['en','fr']",4,

7182,IS,,ISO 2344:1987,"Road vehicles — M14 x 1,25 spark-plugs with conical seating and their cylinder head housing","Véhicules routiers — Bougies d'allumage M14 x 1,25 à siège conique et leur logement dans la culasse",1987-11-19,5,['43.060.50'],ISO/TC 22,9599,[7181],[7183],"['en','fr']",5,

7183,IS,,ISO 2344:1992,"Road vehicles — M14 x 1,25 spark-plugs with conical seating and their cylinder head housing","Véhicules routiers — Bougies d'allumage M14 x 1,25 à siège conique et leur logement dans la culasse",1992-11-25,6,['43.060.50'],ISO/TC 22,9599,"[7181,7182]",[26263],"['en','fr']",5,

7184,IS,,ISO 2345:1981,"Road vehicles — Spark plugs M 18 x 1,5 with conical seating and their cylinder head housing","Véhicules routiers — Bougies d'allumage M 18 x 1,5 à siège conique et leur logement dans la culasse",1981-05-01,3,['43.060.50'],ISO/TC 22,9599,,[7185],"['en','fr']",4,

7185,IS,,ISO 2345:1987,"Road vehicles — M18 x 1,5 spark-plugs with conical seating and their cylinder head housing","Véhicules routiers — Bougies d'allumage M18 x 1,5 à siège conique et leur logement dans la culasse",1987-11-19,4,['43.060.50'],ISO/TC 22,9599,[7184],[21351],"['en','fr']",4,

7186,IS,,ISO 2346:1982,"Road vehicles — Compact spark plugs M 14 x 1,25 with flat seating and their cylinder head housing","Véhicules routiers — Bougies d'allumage M 14 x 1,25 'compactes' à siège plat et leur logement dans la culasse",1982-12-01,3,['43.060.50'],ISO/TC 22,9599,,[7187],"['en','fr']",4,

7187,IS,,ISO 2346:1991,"Road vehicles — M14 x 1,25 compact spark-plugs with flat seating and their cylinder head housing","Véhicules routiers — Bougies d'allumage M14 x 1,25 'compactes' à siège plat et leur logement dans la culasse",1991-10-24,4,['43.060.50'],ISO/TC 22,9599,[7186],[30025],"['en','fr']",4,<p>Specifies the main characteristics of spark-plugs. Two figures illustrate dimensions and tolerances given. This fourth edition cancels and replaces the third edition (1982).</p>

57227,IS,,ISO 23460:2011,Space projects — Programme management — Dependability assurance requirements,Projets spatiaux — Management de programme — Exigences d'assurance de sécurité de fonctionnement,2011-02-23,1,['49.140'],ISO/TC 20/SC 14,9599,,[84726],['en'],18,"<p>ISO 23460:2011 presents the requirements for a dependability (reliability, availability and maintainability) assurance programme for space projects. </p><p>ISO 23460:2011 defines the dependability requirements for space products as well as for system functions implemented in software, and the interaction between hardware and software.</p><p>The provisions of ISO 23460:2011 apply to all programme phases. </p>"

7188,IS,,ISO 2347:1981,"Road vehicles — Compact spark plugs M 14 x 1,25 with conical seating and their head housing","Véhicules routiers — Bougies d'allumage M 14 x 1,25 'compactes' à siège conique et leur logement dans la culasse",1981-05-01,3,['43.060.50'],ISO/TC 22,9599,,[7189],"['en','fr']",4,

7189,IS,,ISO 2347:1987,"Road vehicles — M14 x 1,25 compact spark-plugs with conical seating and their cylinder head housing","Véhicules routiers — Bougies d'allumage M14 x 1,25 'compactes' à siège conique et leur logement dans la culasse",1987-11-19,4,['43.060.50'],ISO/TC 22,9599,[7188],[21349],"['en','fr']",4,

36879,IS,,ISO 23470:2007,Soil quality — Determination of effective cation exchange capacity (CEC) and exchangeable cations using a hexamminecobalt trichloride solution,Qualité du sol — Détermination de la capacité d'échange cationique (CEC) effective et des cations échangeables à l'aide d'une solution de trichlorure de cobaltihexammine,2007-05-04,1,['13.080.20'],ISO/TC 190/SC 3,9599,,"[60543,68765]","['en','fr']",16,"<p>ISO 23470:2007 specifies a method for the determination of the cation exchange capacity (CEC) and the content of exchangeable cations (Al³⁺, Ca²⁺, Fe²⁺, K⁺, Mg²⁺, Mn²⁺, Na⁺) in soils using a hexammin

41581,IS,,ISO 23480:2008,Tools for pressing — Sliding plates,Outillage de presse — Plaques de retenue,2008-03-31,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[60723],"['en','fr']",5,"<p>ISO 23480:2008 specifies the main dimensions and tolerances of sliding plates, to be used in press tools.</p><p>It also specifies the designation of sliding plates.</p>"

41582,IS,,ISO 23481:2008,Tools for pressing — Cam driver plates,Outillage de presse — Plaques d'entraînement de came,2008-03-31,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[62185],"['en','fr']",3,<p>ISO 23481:2008 specifies the main dimensions and tolerances of plates to be used for cam drivers and slides in tools for pressing.</p><p>It also specifies the designation of cam driver plates.</p>

62185,IS,,ISO 23481:2013,Tools for pressing — Cam driver plates,Outillage de presse — Plaques d'entraînement de came,2013-11-27,2,['25.120.10'],ISO/TC 29/SC 8,9599,[41582],[79121],"['en','fr']",3,<p>ISO 23481:2013 specifies the main dimensions and tolerances of plates to be used for cam drivers and slides in tools for pressing. It also specifies the designation of cam driver plates.</p>

7190,IS,,ISO 2349:1973,"Rolling bearings — Tapered roller bearings — Sub-units — Tolerances — Metric series, normal tolerance class and tolerance class 6 — Inch series, tolerance class 4 (normal tolerance class)","Roulements — Roulements à rouleaux coniques — Sous-ensembles — Tolérances — Séries métriques, tolérances classe normale et classe 6 — Séries en inches, tolérances classe 4 (tolérances classe normale)",1973-04-01,1,['21.100.20'],ISO/TC 4,9599,,"[4673,4542]",['en'],2,

75783,IS,,ISO 23498:2020,Graphic technology — Visual opacity of printed white ink,Technologie graphique — Opacité visuelle de l'encre blanche imprimée,2020-09-18,1,['87.080'],ISO/TC 130,9599,,[83546],['en'],9,<p>This document specifies a method of measuring the visual opacity of printed specimens of white ink. It is applicable to printing opaque white ink on transparent and white or coloured opaque substrates.</p>

41593,IS,,ISO 23499:2008,Coal — Determination of bulk density,Charbon — Détermination de la masse volumique en vrac,2008-05-20,1,['73.040'],ISO/TC 27/SC 1,9599,,[63444],"['en','ru']",6,"<p>ISO 23499:2008 provides description of a cone procedure for determining an uncompacted bulk density of crushed coal less than 37 mm in size, such as is charged into coke ovens. It focuses on the uncompacted bulk density of coal resulting from flowing the material into a measuring container (box) in the absence of compacting forces.</p><p>ISO 23499:2008 does not cover procedures for determining a compacted coal bulk density nor to the testing of fine or powdered coal (for boiler or utility application) nor

63444,IS,,ISO 23499:2013,Coal — Determination of bulk density for the use in charging of coke ovens,Charbon — Détermination de la masse volumique en vrac à des fins d'enfournement dans les fours à coke,2013-07-22,2,['73.040'],ISO/TC 27/SC 1,9599,[41593],[89242],['en'],6,"<p>ISO 23499:2013 provides description of a cone procedure for determining an uncompacted bulk density of crushed coal less than 37 mm in size, such as is charged into coke ovens. It focuses on the uncompacted bulk density of coal resulting from flowing the material into a measuring container (box) in the absence of compacting forces.</p><p>ISO 23499:2013 does not cover procedures for determining a compacted coal bulk densit

4123,IS,,ISO 235-1:1975,Withdrawal of ISO 235/1-1975,Annulation de l/ISO 235/1-1975,1975-02-01,1,['25.100.30'],ISO/TC 29,9599,,[4122],['en'],13,

4122,IS,,ISO 235:1980,Parallel shank jobber and stub series drills and Morse taper shank drills,Forets à queue cylindrique courts et extra-courts et forets à queue cône Morse,1980-11-01,2,['25.100.30'],ISO/TC 29/SC 9,9599,[4123],[64191],"['en','fr']",13,"<p>This secon edition, which superseded ISO 235-1:1975, incorporates draft Amendment 1. ISO 235 specifies in dimensions of the above mentioned drills. It comprises, for each type of these drills, three tables giving respectively the dimensions in millimetres, the dimensions in inches, the corrsponding length, in millimetres and in inches, set out as functions of diameter steps.</p>"

26718,IS,Cor,ISO 235:1980/Cor 1:1996,Parallel shank jobber and stub series drills and Morse taper shank drills — Technical Corrigendum 1,Forets à queue cylindrique courts et extra-courts et forets à queue cône Morse — Rectificatif technique 1,1996-07-04,2,['25.100.30'],ISO/TC 29/SC 9,9599,,[64191],['en'],1,

4124,IS,,ISO 235-2:1972,Withdrawal of ISO 235/2-1972,Annulation de l'ISO 235/2-1972,1972-08-01,1,['25.100.30'],ISO/TC 29,9599,,[13651],['en'],4,

67610,IS,,ISO 23500-1:2019,Preparation and quality management of fluids for haemodialysis and related therapies — Part 1: General requirements,Préparation et management de la qualité des liquides d'hémodialyse et de thérapies annexes — Partie 1: Exigences générales,2019-02-15,1,['11.040.40'],ISO/TC 150/SC 2,9599,[61863],[84368],"['en','fr']",87,"1.1 General <p>This document is the base standard for a number of other standards dealing with water treatment equipment, water, dialysis water, concentrates, and dialysis fluid (ISO 23500 series) and provides dialysis practitioners with guidance on the preparation of dialysis fluid for haemodialysis and related therapies and substitution fluid for

67611,IS,,ISO 23500-2:2019,Preparation and quality management of fluids for haemodialysis and related therapies — Part 2: Water treatment equipment for haemodialysis applications and related therapies,Préparation et management de la qualité des liquides d'hémodialyse et de thérapies annexes — Partie 2: Équipement de traitement de l'eau pour des applications en hémodialyse et aux thérapies apparentées,2019-02-15,1,['11.040.40'],ISO/TC 150/SC 2,9599,[61864],[84369],"['en','fr']",34,"1.1 General <p>This document is addressed to the manufacturer and/or supplier of water treatment systems and/or devices used for the express purpose of providing water for haemodialysis or related therapies.</p>1

45345,IS,,ISO 23500:2011,Guidance for the preparation and quality management of fluids for haemodialysis and related therapies,Directives concernant la préparation et le management de la qualité des fluides d'hémodialyse et de thérapies annexes,2011-05-05,1,['11.040.40'],ISO/TC 150/SC 2,9599,,[61863],['en'],82,"<p>ISO 23500:2011 provides dialysis practitioners with guidance on the preparation of dialysis fluid for haemodialysis and related therapies and substitution fluid for use in online therapies, such as haemodiafiltration and haemofiltration. As such, ISO 23500:2011 functions as a recommended practice.</p><p>ISO 23500:2011 addresses the user's responsibility for the dialysis fluid once

61863,IS,,ISO 23500:2014,Guidance for the preparation and quality management of fluids for haemodialysis and related therapies,Directives concernant la préparation et le management de la qualité des fluides d'hémodialyse et de thérapies annexes,2014-03-17,2,['11.040.40'],ISO/TC 150/SC 2,9599,[45345],[67610],"['en','fr']",85,"<p>ISO 23500:2014 provides dialysis practitioners with guidance on the preparation of dialysis fluid for haemodialysis and related therapies and substitution fluid for use in online therapies, such as haemodiafiltration and haemofiltration. As such, ISO 23500:2014 functions as a recommended practice.</p><p>ISO 23500:2014 addresses the user's responsibility for the dialys

67612,IS,,ISO 23500-3:2019,Preparation and quality management of fluids for haemodialysis and related therapies — Part 3: Water for haemodialysis and related therapies,Préparation et management de la qualité des liquides d'hémodialyse et de thérapies annexes — Partie 3: Eau pour hémodialyse et thérapies apparentées,2019-02-15,1,['11.040.40'],ISO/TC 150/SC 2,9599,[61862],[84370],"['en','fr']",19,"<p>This document specifies minimum requirements for water to be used in haemodialysis and related therapies.</p><p>This document includes water to be used in the preparation of concentrates, dialysis fluids for haemodialysis, haemodiafiltration and haemofiltration, and for the reprocessing of haemodi

67613,IS,,ISO 23500-4:2019,Preparation and quality management of fluids for haemodialysis and related therapies — Part 4: Concentrates for haemodialysis and related therapies,Préparation et management de la qualité des liquides d'hémodialyse et de thérapies annexes — Partie 4: Concentrés pour hémodialyse et thérapies apparentées,2019-02-15,1,['11.040.40'],ISO/TC 150/SC 2,9599,[61861],[84371],"['en','fr']",22,"<p>This document specifies minimum requirements for concentrates used for haemodialysis and related therapies. </p><p>This document is addressed to the manufacturer of such concentrates. In several instances in this document, the dialysis fluid is addressed, which is made by the end use

67614,IS,,ISO 23500-5:2019,Preparation and quality management of fluids for haemodialysis and related therapies — Part 5: Quality of dialysis fluid for haemodialysis and related therapies,Préparation et management de la qualité des liquides d'hémodialyse et de thérapies annexes — Partie 5: Qualité des liquides de dialyse pour hémodialyse et thérapies apparentées,2019-02-15,1,['11.040.40'],ISO/TC 150/SC 2,9599,[61860],[84372],"['en','fr']",14,"<p>This document specifies minimum quality requirements for dialysis fluids used in haemodialysis and related therapies.</p><p>This document includes dialysis fluids used for haemodialysis and haemodiafiltration, including substitution fluid for haemodi

36885,IS,,ISO 23509:2006,Bevel and hypoid gear geometry,Géométrie des engrenages coniques et hypoïdes,2006-09-06,1,['21.200'],ISO/TC 60/SC 2,9599,,[63832],"['en','fr']",138,"<p>ISO 23509:2006 specifies the geometry of bevel gears. The term bevel gears is used to mean straight, spiral, zerol bevel and hypoid gear designs. If the text pertains to one or more, but not all, of these, the specific forms are identified.</p><p>ISO 23509:2006 is intended for use by an experienced gear designer capable of selecting reasonable values for the factors based on his knowledge and background. It is not intended for use by the engineering public at large.</p>"

63832,IS,,ISO 23509:2016,Bevel and hypoid gear geometry,Géométrie des engrenages coniques et hypoïdes,2016-11-16,2,['21.200'],ISO/TC 60/SC 2,9599,[36885],"[85501,85503]","['en','fr']",138,"<p>ISO 23509:2016 specifies the geometry of bevel gears.</p><p>The term bevel gears is used to mean straight, spiral, zerol bevel and hypoid gear designs. If the text pertains to one or more, but not all, of these, the specific forms are identified.</p><p>The manufacturing process of forming the desired tooth form is not intended to imply any specific process, but rather to be general in nature and applicable to all methods of manufacture.</p><p>The geometry for the calculation of factors used in bevel gea

28549,IS,,ISO 2351-1:2002,Assembly tools for screws and nuts — Machine-operated screwdriver bits — Part 1: Screwdriver bits for slotted head screws,Outils de manoeuvre pour vis et écrous — Embouts tournevis à machine — Partie 1: Embouts tournevis pour vis à tête fendue,2002-08-15,1,['25.140.01'],ISO/TC 29/SC 10,9599,[7192],[41054],"['en','fr']",5,"<p>ISO 2351-1 prescribes the technical specifications for machine-operated screwdriver bits for slotted head screws. It applies to bits with male hexagon drive or with cylindrical flat end drive as defined in ISO 1173, and to tips for screwdrivers Type C as defined in ISO 2380-1.</p><p>It also gives recommended combinations between tips and bits.</

7191,IS,,ISO 2351:1972,"Screwdriver bits, for slotted head screws, with male hexagon drive","Embouts tournevis pour vis à tête fendue, à hexagone conducteur mâle",1972-06-01,1,['25.140.01'],ISO/TC 29,9599,,[7192],"['en','fr']",1,

7192,IS,,ISO 2351:1986,"Screwdriver bits for slotted head screws, with male hexagon drive","Embouts tournevis pour vis à tête fendue, à hexagone conducteur mâle",1986-11-13,2,['25.140.01'],ISO/TC 29/SC 10,9599,[7191],[28549],"['en','fr']",2,

29902,IS,,ISO 2351-3:2002,Assembly tools for screws and nuts — Machine-operated screwdriver bits — Part 3: Screwdriver bits for hexagon socket screws,Outils de manoeuvre pour vis et écrous — Embouts tournevis à machine — Partie 3: Embouts tournevis pour vis à six pans creux,2002-08-15,1,['25.140.01'],ISO/TC 29/SC 10,9599,"[8260,26667]",[61604],"['en','fr']",5,"<p>ISO 2351-3 prescribes the technical specifications for machine-operated screwdriver bits for hexagon socket screws. It applies to bits with male hexagon drive or with cylindrical flat end drive as defined in ISO 1173, and to tips for screwdrivers as defined in ISO 2936.</p><p>It gives also recommended combinations between tips and b

7193,IS,,ISO 2352:1982,Spiral ratchet screwdriver ends,Entraînement pour tournevis automatiques,1982-12-01,2,['25.140.30'],ISO/TC 29/SC 10,9599,,[29927],"['en','fr']",1,

36888,IS,,ISO 23529:2004,Rubber — General procedures for preparing and conditioning test pieces for physical test methods,Caoutchouc — Procédures générales pour la préparation et le conditionnement des éprouvettes pour les méthodes d'essais physiques,2004-09-07,1,['83.060'],ISO/TC 45/SC 2,9599,"[10611,2230,20168,8675]",[50758],"['en','fr']",15,"<p>ISO 23529:2004 specifies conditions and procedures for the preparation, measurement, marking, storage and conditioning of rubber test pieces for use in physical tests specified in other International Standards, and the preferred conditions to be used during the tests. Special conditions applicable to a particular test or material or simulating a pa

50758,IS,,ISO 23529:2010,Rubber — General procedures for preparing and conditioning test pieces for physical test methods,Caoutchouc — Procédures générales pour la préparation et le conditionnement des éprouvettes pour les méthodes d'essais physiques,2010-10-22,2,['83.060'],ISO/TC 45/SC 2,9599,[36888],[70323],"['en','fr','ru']",16,"<p>ISO 23529:2010 specifies general procedures for the preparation, measurement, marking, storage, and conditioning of rubber test pieces for use in physical tests specified in other International Standards, and the preferred conditions to be used during the tests. Special conditions, applicable to a particular test or material or simulating a particular climatic

67105,IS,,ISO 23537-1:2016,Requirements for sleeping bags — Part 1: Thermal and dimensional requirements,Exigences pour les sacs de couchage — Partie 1: Exigences thermiques et dimensionnelles,2016-09-30,1,['97.200.30'],ISO/TC 83,9599,,"[82789,73880]","['en','fr']",21,"<p>ISO 23537-1:2016 specifies the requirements and test methods as well as provisions for labelling of adult sized sleeping bags for use in sports and leisure time activities.</p><p>ISO 23537-1:2016 does not apply to sleeping bags intended for specific purpose such as military use and extreme climate zone expedition. It does not apply to sleeping bags for children or babies.</p><p>NOTE 1 No prediction model exists for th

73657,IS,Amd,ISO 23537-1:2016/Amd 1:2018,Requirements for sleeping bags — Part 1: Thermal and dimensional requirements — Amendment 1,Exigences pour les sacs de couchage — Partie 1: Exigences thermiques et dimensionnelles — Amendement 1,2018-01-08,1,['97.200.30'],ISO/TC 83,9599,,"[82789,73880]","['en','fr']",1,

67112,IS,,ISO 23537-2:2016,Requirements for sleeping bags — Part 2: Fabric and material properties,Exigences pour les sacs de couchage — Partie 2: Propriétés de l'étoffe et des matières,2016-09-30,1,['97.200.30'],ISO/TC 83,9599,,"[82790,73881]","['en','fr']",6,"<p>ISO 23537-2:2016 specifies the fabric and material properties as well as provisions for labelling of adult sized sleeping bags for use in sports and leisure time activities. Thermal and dimensional requirements are specified in ISO 23537‑1.</p><p>ISO 23537-2:2016 does not apply to sleeping bags intended for specific purpose such as military use and extreme climate zone expedition. It does not apply to sleeping bags for children or

41641,IS,,ISO 23539:2005,Photometry — The CIE system of physical photometry,Photométrie — Le système CIE de photométrie physique,2005-07-26,1,['17.180.01'],CIE,9599,,[83178],"['en','fr']",18,"<p>ISO 23539:2005 specifies the characteristics of the system of physical photometry established by the CIE and accepted as the basis for the measurement of light. It defines the photometric quantities, units and standards that make up the CIE system of physical photometry and that have been officially accepted by the Comité International des Poids et Mesures (CIPM).</p>"

36890,IS,,ISO 23550:2004,Safety and control devices for gas burners and gas-burning appliances — General requirements,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences générales,2004-10-01,1,['27.060.20'],ISO/TC 161,9599,,[57045],"['en','fr']",37,"<p>ISO 23550:2004 specifies safety, constructional and performance requirements and testing of safety control or regulating devices and sub-assemblies or fittings (hereafter referred to as controls) for burners and gas-burning appliances using fuel gases as natural gas, manufactured gas or liquefied petroleum gas (LPG). It is not applicable to corrosive and waste gases.</p><p>ISO 23550:2004 is applicable to t

57045,IS,,ISO 23550:2011,Safety and control devices for gas burners and gas-burning appliances — General requirements,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences générales,2011-03-10,2,['27.060.20'],ISO/TC 161,9599,"[51636,36890]",[60451],"['en','fr']",41,"<p>ISO 23550:2011 specifies safety, constructional and performance requirements and testing of safety control or regulating devices and sub-assemblies or fittings for burners and gas-burning appliances using such fuel gases as natural gas, manufactured gas or liquefied petroleum gas (LPG). It is not applicable to corrosive and waste gases.</p><p>ISO 23550:2011 is applicable to the following con

61951,IS,Amd,ISO 23550:2011/Amd 1:2015,Safety and control devices for gas burners and gas-burning appliances — General requirements — Amendment 1,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences générales — Amendement 1,2015-11-03,2,['27.060.20'],ISO/TC 161,9599,,[60451],['en'],7,

36891,IS,,ISO 23551-1:2006,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 1: Automatic valves,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences particulières — Partie 1: Robinets automatiques,2006-06-28,1,['27.060.20'],ISO/TC 161,9599,,[54346],['en'],18,"<p>ISO 23551-1:2006 specifies safety, constructional and performance requirements and testing of automatic valves (hereafter referred to as valves) for gas burners, gas appliances and similar use.</p><p>ISO 23551-1:2006 covers type testing only.</p><p>ISO 23551-1:2006 applies to valves with declared maximum working pressures up to and including 5

54346,IS,,ISO 23551-1:2012,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 1: Automatic and semi-automatic valves,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences particulières — Partie 1: Robinets automatiques et semi-automatiques,2012-08-08,2,['27.060.20'],ISO/TC 161,9599,[36891],"[83847,75139]",['en'],37,"<p>ISO 23551-1:2012 specifies safety, constructional and performance requirements and testing of automatic and semi-automatic shut-off valves for gas burners, gas appliances and appliances of similar use.</p><p>It applies to</p><ul><li> normally closed valves,</li><li> valves bein

68556,IS,,ISO 23551-10:2016,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 10: Vent valves,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences particulières — Partie 10: Robinets d'évent,2016-07-18,1,['27.060.20'],ISO/TC 161,9599,,[85515],['en'],18,"<p>ISO 23551-10:2016 specifies the safety, design, construction and performance requirements and testing for automatic vent valves (hereafter referred to as 'valves') for use with gas burners, gas appliances burning one or more gaseous fuels.</p><p>It is applicable to valves with declared maximum inlet pressures up to and including 500 kPa (5 bar) of no

41170,IS,,ISO 23551-2:2006,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 2: Pressure regulators,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences particulières — Partie 2: Régulateurs de pression,2006-06-29,1,['27.060.20'],ISO/TC 161,9599,,[66515],['en'],38,"<p>ISO 23551-2:2006 specifies safety, constructional and performance requirements for pressure regulators intended for use with gas burners and gas burning appliances. It also describes the test procedures for checking compliance with these requirements and provides information necessary for the purchaser and user. </p><p>ISO 23551-2:2006 ap

36931,IS,,ISO 23551-4:2005,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 4: Valve-proving systems for automatic shut-off valves,Dispositifs de contrôle et de sécurité pour les brûleurs à gaz et pour les appareils utilisant le gaz — Exigences particulières — Partie 4: Systèmes de contrôle d'étanchéité pour robinets automatiques de sectionnement,2005-08-24,1,['27.060.20'],ISO/TC 161,9599,,[68290],['en'],15,"<p>ISO 23551-4:2005 specifies safety, constructional and performance requirements of valve-proving systems, hereafter referred to as VPS, intended for use with gas burners and gas-burning appliances. It also describes the test procedu

51959,IS,Amd,ISO 23551-4:2005/Amd 1:2010,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 4: Valve-proving systems for automatic shut-off valves — Amendment 1: Application guidance for the valve-proving system,Dispositifs de contrôle et de sécurité pour les brûleurs à gaz et pour les appareils utilisant le gaz — Exigences particulières — Partie 4: Systèmes de contrôle d'étanchéité pour robinets automatiques de sectionnement — Amendement 1: Guide d'application pour le système de contrôle d'étanchéité,2010-10-28,1,['27.060.20'],ISO/TC 161,9599,,[68290],['en'],3,

60486,IS,,ISO 23551-5:2014,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 5: Manual gas valves,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences particulières — Partie 5: Robinets de gaz manuels,2014-05-08,1,['27.060.20'],ISO/TC 161,9599,,[75895],['en'],33,"<p>ISO 23551-5:2014 specifies safety, constructional and performance requirements for manual gas valves intended for use with gas burners and gas-burning appliances, hereafter referred to as ?valves', unless otherwise specified.</p><p>ISO 23551-5:2014 applies to following types of manual gas valves:</p><ul><li>manual gas shut-off valve;</li><l

60520,IS,,ISO 23551-6:2014,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 6: Thermoelectric flame supervision controls,Dispositifs de commande et de sécurité pour brûleurs à gaz et appareils à gaz — Exigences particulières — Partie 6: Équipements thermoélectriques de surveillance de flamme,2014-08-06,1,['27.060.20'],ISO/TC 161,9599,,[77901],['en'],18,"<p>ISO 23551-6:2014 specifies safety, constructional, and performance requirements for thermoelectric flame supervision controls, energized by a thermocouple, intended for use with gas burners and gas-burning appliances, hereafter referred to as 'controls'.</p><p>ISO 23551-6:2014 applies

62335,IS,,ISO 23551-8:2016,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 8: Multifunctional controls,Dispositifs de commande et de sécurité pour les brûleurs et les appareils à gaz — Exigences particulières — Partie 8: Equipements multifonctionnels,2016-02-02,1,['27.060.20'],ISO/TC 161,9599,,[83563],['en'],7,"<p>ISO 23551-8:2016 specifies the safety, construction and performance requirements for multifunctional controls intended for use with gas burners, gas appliances and similar use, hereafter referred to as 'MFC'.</p><p>ISO 23551-8:2016 is applicable to MFC with declared maximum inlet pressures up to, and including, 50 kPa (500 mbar

71282,IS,Amd,ISO 23551-8:2016/Amd 1:2019,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 8: Multifunctional controls — Amendment 1: Overheating safety devices,Dispositifs de commande et de sécurité pour les brûleurs et les appareils à gaz — Exigences particulières — Partie 8: Equipements multifonctionnels — Amendement 1: Dispositifs de sécurité contre les surchauffes,2019-06-18,1,['27.060.20'],ISO/TC 161,9599,,[83563],['en'],5,

64957,IS,,ISO 23551-9:2015,Safety and control devices for gas burners and gas-burning appliances — Particular requirements — Part 9: Mechanical gas thermostats,Dispositifs de commande et de sécurité pour brûleurs à fioul et pour appareils à fioul - Exigences particulières — Partie 9: Thermostats mécaniques,2015-08-14,1,['27.060.20'],ISO/TC 161,9599,,[78036],['en'],26,"<p>ISO 23551-9:2015 specifies safety, constructional, and performance requirements and testing of mechanical gas thermostat for gas burners, gas appliances, and similar use hereafter referred to as 'thermostats'.</p><p>ISO 23551-9:2015 covers type testing only.</p><p>ISO 23551-9:2015 applies to mechanical gas thermostats of nom

41153,IS,,ISO 23552-1:2007,"Safety and control devices for gas and/or oil burners and gas and/or oil appliances — Particular requirements — Part 1: Fuel/air ratio controls, electronic type",Dispositifs de commande et de sécurité pour brûleurs à gaz et/ou à fioul et pour appareils à gaz et/ou à fioul — Exigences particulières — Partie 1: Dispositifs de régulation du rapport air/combustible de type électronique,2007-10-09,1,['27.060.20'],ISO/TC 161,9599,,[86010],['en'],21,"<p>ISO 23552-1:2007 specifies safety, construction and performance requirements for electronic fuel/air ratio control systems intended for use with gas or oil burners and gas or oil burning appliances. ISO 23552-1:2007 also

51633,IS,Amd,ISO 23552-1:2007/Amd 1:2010,"Safety and control devices for gas and/or oil burners and gas and/or oil appliances — Particular requirements — Part 1: Fuel/air ratio controls, electronic type — Amendment 1: Addition to the specific regional requirements in Japan",Dispositifs de commande et de sécurité pour brûleurs à gaz et/ou à fioul et pour appareils à gaz et/ou à fioul — Exigences particulières — Partie 1: Dispositifs de régulation du rapport air/combustible de type électronique — Amendement 1: Addition aux exigences spécifiques régionales au Japon,2010-09-29,1,['27.060.20'],ISO/TC 161,9599,,[86010],['en'],1,

36893,IS,,ISO 23553-1:2007,Safety and control devices for oil burners and oil-burning appliances — Particular requirements — Part 1: Shut-off devices for oil burners,Dispositifs de commande et de sécurité pour brûleurs à fioul et pour appareils à fioul — Exigences particulières — Partie 1: Dispositifs de coupure pour brûleurs à fioul,2007-09-10,1,['27.060.10'],ISO/TC 161,9599,,[57050],"['en','fr']",20,"<p>ISO 23553-1 specifies safety, constructional and performance requirements, and testing of safety shut-off devices, for liquid fuels. </p><p>ISO 23553-1 covers type testing only.</p><p>It applies to safety shut-off devices which: are designed as e.g. automatic valves or fast-closing devices;

53552,IS,Cor,ISO 23553-1:2007/Cor 1:2009,Safety and control devices for oil burners and oil-burning appliances — Particular requirements — Part 1: Shut-off devices for oil burners — Technical Corrigendum 1,Dispositifs de commande et de sécurité pour brûleurs à fioul et pour appareils à fioul — Exigences particulières — Partie 1: Dispositifs de coupure pour brûleurs à fioul — Rectificatif technique 1,2009-01-23,1,['27.060.10'],ISO/TC 161,9599,,[57050],['en'],1,

57050,IS,,ISO 23553-1:2014,Safety and control devices for oil burners and oil-burning appliances — Particular requirements — Part 1: Automatic and semi-automatic valves,Dispositifs de commande et de sécurité pour brûleurs à combustible liquide et pour appareils à combustible liquide — Exigences particulières — Partie 1: Robinets automatiques et semi-automatiques,2014-05-13,2,['27.060.10'],ISO/TC 161,9599,"[36893,53552]",[74771],"['en','fr']",36,"<p>ISO 23553-1:2014 specifies safety, constructional and performance requirements and testing of automatic and semi-automatic valves for oil.</p><p>It applies to automatic and semi-automatic valves which are:</p><p>-normally closed;</p><p>-used in co

41659,IS,,ISO 23559:2007,Plastics — Film and sheeting — Guidance on the testing of thermoplastic films,Plastiques — Film et feuille — Lignes directrices pour les essais de films thermoplastiques,2007-08-23,1,['83.140.10'],ISO/TC 61/SC 11,9599,,[60303],['en'],8,"<p>ISO 23559:2007 identifies specific test procedures to assist producers and users in the selection and characterization of thermoplastic films in single- or multi-layer form. It is intended to serve as a guide for those films for which there are no existing standards or specifications.</p><p>NOTE Because of the range of materials used and the wide variety of processes available to produce various film constructions, the sta

41660,IS,,ISO 23560:2008,Woven polypropylene sacks for bulk packaging of foodstuffs,Sacs tissés en polypropylène pour l'emballage en vrac de denrées alimentaires,2008-09-17,1,"['83.140.99','55.080']",ISO/TC 61/SC 11,9599,,"[63507,65221]",['en'],9,"<p>ISO 23560:2008 specifies the general characteristics, requirements and methods of test for woven polypropylene (PP) sacks. It is applicable to woven PP sacks, having a capacity of 50 kg or 25 kg, intended for the transport and storage of foodstuffs, such as cereals, sugar and pulses.</p>"

39928,IS,,ISO 23570-3:2006,Industrial automation systems and integration — Distributed installation in industrial applications — Part 3: Power distribution bus,Systèmes d'automatisation industrielle et intégration — Installation distribuée dans les applications industrielles — Partie 3: Bus de distribution d'énergie,2006-08-10,1,['25.040.01'],ISO/TC 184/SC 1,9599,,[53400],['en'],23,"<p>The scope of ISO 23570 is the interconnection of elements in the control system of machine tools and similar large pieces of industrial automation. This specification includes cable types, sizes, and sheath colours, connector types and contact assignments, and diagnostic functions appropriate to the sensors an

7197,IS,,ISO 2358:1972,Prevailing torque-type steel hexagon locknuts — Dimensions — Metric series,Écrous de blocage hexagonaux en acier à freinage interne — Dimensions — Série métrique,1972-10-01,1,['21.060.20'],ISO/TC 2,9599,,"[13601,13605,13606,13603,13599]","['en','fr']",1,

76107,IS,,ISO 23581:2020,Petroleum products and related products — Determination of kinematic viscosity — Method by Stabinger type viscometer,Produits pétroliers et produits connexes — Détermination de la viscosité cinématique — Méthode avec un viscosimètre type Stabinger,2020-07-17,1,['75.080'],ISO/TC 28,9599,,[81855],['en'],9,"<p>This document specifies a procedure for the determination of kinematic viscosity (<i>ν</i>) at 40 °C in the range from 2 mm²/s to 6 mm²/s by calculation from dynamic viscosity (<i>η</i>) and density (<i>ρ</i>) of middle distillate fuels, fatty acid methyl ester fuels (FAME) and mixtures of these using the Stabinger type viscometer.</p><p>The

55867,IS,,ISO 23599:2012,Assistive products for blind and vision-impaired persons — Tactile walking surface indicators,Produits d'assistance pour personnes aveugles ou visuellement affaiblies — Indicateurs tactiles de surfaces de marche,2012-03-02,1,['11.180.30'],ISO/TC 173,9599,,[76106],['en'],37,

4126,IS,,ISO 236-2:1976,"Long fluted machine reamers, Morse taper shanks","Alésoirs à machine, à goujures longues, à queue cône Morse",1976-11-01,1,['25.100.30'],ISO/TC 29,9599,,[60697],"['en','fr']",4,"<p>This part of ISO 236 specifies the dimensions of the long fluted machine reamers. It comprises three tables giving respectively the preferred sizes with corresponding dimensions in millimetres, and in inches, the corresponding sizes, in millimetres and in inches, set out as functions of diameter steps. Provision is also made for tolernces on lengths and cutting diameters.</p>"

7199,IS,,ISO 2360:1982,Non-conductive coatings on non-magnetic basis metals — Measurement of coating thickness — Eddy current method,Revêtements non conducteurs sur métal de base non magnétique — Mesurage de l'épaisseur — Méthode des courants de Foucault,1982-08-01,2,['25.220.20'],ISO/TC 107,9599,,[31240],"['en','fr']",3,"<p>This second edition cancels and replaces the first edition (i. e. ISO 2360:1972). Specifies a non-destructive measurement. The method is applicable for measurements of the thickness of most oxide coatings produced by anodizing, but it is not applicable to all conversion coatings, some of which are too thin to be measured by this method.</p>"

31240,IS,,ISO 2360:2003,Non-conductive coatings on non-magnetic electrically conductive basis materials — Measurement of coating thickness — Amplitude-sensitive eddy-current method,Revêtements non conducteurs sur matériaux de base non magnétiques conducteurs de l'électricité — Mesurage de l'épaisseur de revêtement — Méthode par courants de Foucault sensible aux variations d'amplitude,2003-11-14,3,['25.220.20'],ISO/TC 107,9599,[7199],[69943],"['en','fr']",11,"<p>ISO 2360:2003 describes a method for non-destructive measurements of the thickness of non-conductive coatings on non-magnetic, electrically conductive (generally metallic) basis materials, using amplitude-sensitive eddy current instru

41685,IS,,ISO 23601:2009,Safety identification — Escape and evacuation plan signs,Identification de sécurité — Plans d'évacuation et de secours,2009-02-09,1,['01.080.10'],ISO/TC 145/SC 2,9599,,[80678],"['en','fr','ru']",13,"<p>ISO 23601:2009 establishes design principles for displayed escape plans that contain information relevant to fire safety, escape, evacuation and rescue of the facility's occupants. These plans may also be used by intervention forces in case of emergency.</p><p>These plans are intended to be displayed as signs in public areas and workplaces.</p><p>ISO 23601:2009 is not intended to cover the plans to be used by external safety services nor detailed professional technical

41694,IS,,ISO 23603:2005,Standard method of assessing the spectral quality of daylight simulators for visual appraisal and measurement of colour,Méthode normalisée d'évaluation de la qualité spectrale des simulateurs de lumière du jour pour le jugement visuel et la mesure des couleurs,2005-07-22,1,['17.180.20'],CIE,9599,,[82661],"['en','fr']",19,"<p>ISO/CIE 23603:2005 specifies a method of assessing the spectral quality of the irradiance provided by a daylight simulator to be used for visual appraisal of colours or for colour measurements and a method of assigning a quality grade to the simulator. It specifies the maximum permissible deviation of the chromaticity of the simulator from the ch

7200,IS,,ISO 2361:1982,Electrodeposited nickel coatings on magnetic and non-magnetic substrates — Measurement of coating thickness — Magnetic method,Revêtements électrolytiques de nickel sur métal de base magnétique et non magnétique — Mesurage de l'épaisseur — Méthode magnétique,1982-08-01,2,['25.220.40'],ISO/TC 107,9599,,"[88325,81824]","['en','fr']",4,"<p>This second edition cancels and replaces the first edition (i. e. ISO 2361:1972). Specifies the method of using coating thickness instruments of the magnetic type ror non-destructive measurements of the thickness. The method may nkot be applicable to autocatalytic (electroless) nickel coatings. For the purpose of this Standasd, two types

36914,IS,,ISO 23611-1:2006,Soil quality — Sampling of soil invertebrates — Part 1: Hand-sorting and formalin extraction of earthworms,Qualité du sol — Prélèvement des invertébrés du sol — Partie 1: Tri manuel et extraction au formol des vers de terre,2006-02-03,1,"['13.080.30','13.080.05']",ISO/TC 190/SC 4,9599,,[70449],"['en','fr']",12,<p>ISO 23611-1:2006 specifies a method for sampling and handling earthworms from field soils as a prerequisite for using these animals as bioindicators (e.g. to assess the quality of a soil as a habitat for organisms).</p><p>ISO 23611-1:2006 applies to all terrestrial biotopes in which earthworms occur. It is not applicable for semi-terrestrial soils and it c

70449,IS,,ISO 23611-1:2018,Soil quality — Sampling of soil invertebrates — Part 1: Hand-sorting and extraction of earthworms,Qualité du sol — Prélèvement des invertébrés du sol — Partie 1: Tri manuel et extraction des vers de terre,2018-05-24,2,"['13.080.30','13.080.05']",ISO/TC 190/SC 4,9599,[36914],[88092],"['en','fr']",19,"<p>This document specifies a method for sampling and handling earthworms from field soils as a prerequisite for using these animals as bioindicators (e.g. to assess the quality of a soil as a habitat for organisms).</p><p>This document applies to all terrestrial biotopes in which earthworms occur. The sampling design of field studies in general is given in ISO 18400‑101

37027,IS,,ISO 23611-2:2006,Soil quality — Sampling of soil invertebrates — Part 2: Sampling and extraction of micro-arthropods (Collembola and Acarina),Qualité du sol — Prélèvement des invertébrés du sol — Partie 2: Prélèvement et extraction des micro-arthropodes (Collembola et Acarina),2006-02-03,1,"['13.080.30','13.080.05']",ISO/TC 190/SC 4,9599,,[85217],"['en','fr']",12,"<p>ISO 23611-2:2006 specifies a method for sampling, extracting and preserving collembolans and mites from field soils as a prerequisite for using these animals as bio-indicators (e.g. to assess the quality of a soil as a habitat for organisms).</p><p>The sampling and extraction methods of ISO 23611-2:2006 are applicable

39246,IS,,ISO 23611-3:2007,Soil quality — Sampling of soil invertebrates — Part 3: Sampling and soil extraction of enchytraeids,Qualité du sol — Prélèvement des invertébrés du sol — Partie 3: Prélèvement et extraction des enchytréides,2007-04-24,1,"['13.080.30','13.080.05']",ISO/TC 190/SC 4,9599,,[72744],"['en','fr']",12,"<p>ISO 23611-3:2007 specifies a method for sampling, handling and extracting enchytraeids from terrestrial field soils as a prerequisite for using these animals as bioindicators (e.g. to assess the quality of a soil as a habitat for organisms). It applies to all terrestrial biotopes in which enchytraeids occur. </p><p>ISO 23611-3:2007 is not applicable for semi-terrestrial

41868,IS,,ISO 23611-4:2007,"Soil quality — Sampling of soil invertebrates — Part 4: Sampling, extraction and identification of soil-inhabiting nematodes","Qualité du sol — Prélèvement des invertébrés du sol — Partie 4: Prélèvement, extraction et identification des nématodes du sol",2007-11-13,1,"['13.080.30','13.080.05']",ISO/TC 190/SC 4,9599,,[77794],"['en','fr']",19,<p>ISO 23611-4:2007 specifies a method for sampling and handling free-living nematodes from terrestrial field soils as a prerequisite for using them as bio-indicators (e.g. to assess the quality of a soil as a habitat for organisms).</p><p>ISO 23611-4:2007 applies to all terrestrial biotopes in which nematodes occur. It is not

50777,IS,,ISO 23611-5:2011,Soil quality — Sampling of soil invertebrates — Part 5: Sampling and extraction of soil macro-invertebrates,Qualité du sol — Prélèvement des invertébrés du sol — Partie 5: Prélèvement et extraction des macro-invertébrés du sol,2011-11-23,1,"['13.080.30','13.080.05']",ISO/TC 190/SC 4,9599,,[85218],"['en','fr']",12,"<p>ISO 23611-5:2011 specifies a method for sampling, extracting and preserving macro-invertebrates from soils, including the litter zone. The proposed method is a prerequisite for using these animals as bio-indicators (e.g. to assess the quality of a soil as a habitat for organisms). The main premise of this method is rapid assessment (completing the samp

50778,IS,,ISO 23611-6:2012,Soil quality — Sampling of soil invertebrates — Part 6: Guidance for the design of sampling programmes with soil invertebrates,Qualité du sol — Prélèvement des invertébrés du sol — Partie 6: Lignes directrices pour la conception de programmes d'échantillonnage des invertébrés du sol,2012-09-19,1,"['13.080.30','13.080.05']",ISO/TC 190/SC 4,9599,,[88095],"['en','fr']",41,"<p>This part of ISO 23611 provides guidance for the design of field studies with soil invertebrates (e.g. for the</p><p>monitoring of the quality of a soil as a habitat for organisms). Detailed information on the sampling of the</p><p>most important soil organisms is provided in the other parts of t

76407,IS,,ISO 23616:2022,"Cleaning, inspection and repair of firefighters' personal protective equipment (PPE)","Nettoyage, inspection et réparation des équipements de protection individuelle (PPE) des pompiers",2022-04-28,1,['13.340.10'],ISO/TC 94/SC 14,9599,,[85650],['en'],37,"<p>This document gives requirements, guidance and recommendations for the cleaning, inspection, and repair of PPE for use by firefighters.</p><p>This document is intended to be used by those responsible for the cleaning, inspections, and repair of firefighters PPE, however, it will also provide vital guidance to those who are responsible for establishing such a programme including fire and rescue services.</p><p>This

76592,IS,,ISO 23665:2021,Unmanned aircraft systems — Training for personnel involved in UAS operations,Aéronefs sans pilote — Formation du personnel impliqué dans l'exploitation d'UAS,2021-02-02,1,"['03.100.30','49.020']",ISO/TC 20/SC 16,9599,,[83175],['en'],35,"<p>This document describes the procedures for training personnel who will be involved in the operation of unmanned aircraft systems (UAS).</p><p>This document defines:</p><p>a) knowledge, skill, attitude and qualification criteria that are needed for UAS pilots and training organizations that provides training to trainees of UAS remote pilots and other personnel involved in UAS operations;</p><p>b) training curriculum and content