Withdrawn and superseded ISO standards — page 82 of 246

36566,IS,,ISO 22958:2005,Textiles — Water resistance — Rain tests: exposure to a horizontal water spray,Textiles — Résistance à l'eau — Essai d'arrosage: exposition à une pulvérisation horizontale,2005-03-21,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[78001],"['en','fr']",7,"<p>ISO 22958:2005 is applicable to any textile fabric, which may or may not have been given a water-resistant or water-repellent finish. It measures the resistance of fabrics to the penetration of water by impact, and thus can be used to predict the probable rain penetration resistance of textile fabrics. It is especially suitable for measuring apparel fabrics. Tests may be made at different intensities of water impact to give

55018,IS,Cor,ISO 22958:2005/Cor 1:2009,Textiles — Water resistance — Rain tests: exposure to a horizontal water spray — Technical Corrigendum 1,Textiles — Résistance à l'eau — Essai d'arrosage: exposition à une pulvérisation horizontale — Rectificatif technique 1,2009-10-19,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[78001],"['en','fr']",2,

7123,IS,,ISO 2296:1972,Metal slitting saws with fine and coarse teeth — Metric series,Fraises-scies à dentures fine et grosse — Série métrique,1972-07-01,1,['25.100.40'],ISO/TC 29/SC 9,9599,,[50892],"['en','fr']",3,"<p>Specifies the mechanical characteristics. It concerns saws with fine teeth (see table 1) and with coarse teeth (see table 2). The ratio between the number of teeth saws with coarse teeth and the number of teeth for saws with fine teeth is 0,5, and specific values have been related to saws diameters and thicknesses. If there is a need to extend the range or introduce other series of teeth,such additions should be in accordance with data given in the annex.</p>"

50892,IS,,ISO 2296:2011,Metal slitting saws with fine and coarse teeth — Metric series,Fraises-scies à dentures fine et grosse — Série métrique,2011-09-26,2,['25.100.40'],ISO/TC 29/SC 9,9599,[7123],[75802],"['en','fr']",4,"<p>ISO 2296:2011 specifies the dimensions and the mechanical characteristics of metal slitting saws, metric series. It applies to the following two types of metal slitting saws:</p><ul><li>metal slitting saws with fine teeth;</li><li>metal slitting saws with coarse teeth.</li></ul>"

3610,IS,,ISO 23:1976,Cinematography — Camera usage of 35 mm motion- picture film — Specifications,Cinématographie — Position du film cinématographique de 35 mm dans le couloir de la caméra,1976-12-01,1,['37.060.10'],ISO/TC 36,9599,,[20575],"['en','fr']",1,

4107,IS,,ISO 230-1:1986,Acceptance code for machine tools — Part 1: Geometric accuracy of machines operating under no-load or finishing conditions,Code de réception des machines-outils — Partie 1: Précision géométrique des machines fonctionnant à vide ou dans des conditions de finition,1986-09-04,1,['25.080.01'],ISO/TC 39/SC 2,9599,[4106],[4108],"['en','fr']",46,

4108,IS,,ISO 230-1:1996,Test code for machine tools — Part 1: Geometric accuracy of machines operating under no-load or finishing conditions,Code d'essai des machines-outils — Partie 1: Précision géométrique des machines fonctionnant à vide ou dans des conditions de finition,1996-07-04,2,['25.080.01'],ISO/TC 39/SC 2,9599,[4107],"[46442,46449]","['en','fr']",62,

44672,IS,,ISO 230-10:2011,Test code for machine tools — Part 10: Determination of the measuring performance of probing systems of numerically controlled machine tools,Code d'essai des machines-outils — Partie 10: Détermination des performances de mesure des systèmes de palpage des machines-outils à commande numérique,2011-05-06,1,['25.080.01'],ISO/TC 39/SC 2,9599,,[68492],"['en','fr']",38,"<p>ISO 230-10:2011 specifies test procedures to evaluate the measuring performance of contacting probing systems (used in a discrete-point probing mode) integrated with a numerically controlled machine tool.</p><p>It does not include other types of probing systems, such as those used in scanning mode or n

55645,IS,Amd,ISO 230-10:2011/Amd 1:2014,Test code for machine tools — Part 10: Determination of the measuring performance of probing systems of numerically controlled machine tools — Amendment 1: Measuring performance with scanning probes,Code d'essai des machines-outils — Partie 10: Détermination des performances de mesure des systèmes de palpage des machines-outils à commande numérique — Amendement 1: Performances de mesure avec palpeurs de scanning,2014-09-10,1,['25.080.01'],ISO/TC 39/SC 2,9599,,[68492],"['en','fr']",9,

68492,IS,,ISO 230-10:2016,Test code for machine tools — Part 10: Determination of the measuring performance of probing systems of numerically controlled machine tools,Code d'essai des machines-outils — Partie 10: Détermination des performances de mesure des systèmes de palpage des machines-outils à commande numérique,2016-02-03,2,['25.080.01'],ISO/TC 39/SC 2,9599,"[44672,55645]",[78909],"['en','fr']",45,"<p>ISO 230-10:2016 specifies test procedures to evaluate the measuring performance of contacting probing systems (used in a discrete-point probing mode) integrated with a numerically controlled machine tool.</p><p>It does not include other types of probing systems, such as those used in sca

4109,IS,,ISO 230-2:1988,Acceptance code for machine tools — Part 2: Determination of accuracy and repeatability of positioning of numerically controlled machine tools,Code de réception des machines-outils — Partie 2: Détermination de la précision et de la répétabilité de positionnement des machines-outils à commande numérique,1988-11-03,1,['25.040.20'],ISO/TC 39/SC 2,9599,,[26966],"['en','fr']",7,

26966,IS,,ISO 230-2:1997,Test code for machine tools — Part 2: Determination of accuracy and repeatability of positioning numerically controlled axes,Code d'essai des machines-outils — Partie 2: Détermination de la précision et de la répétabilité de positionnement des axes en commande numérique,1997-12-25,2,['25.040.20'],ISO/TC 39/SC 2,9599,[4109],[35988],"['en','fr']",15,

31798,IS,Cor,ISO 230-2:1997/Cor 1:1999,Test code for machine tools — Part 2: Determination of accuracy and repeatability of positioning numerically controlled axes — Technical Corrigendum 1,Code d'essai des machines-outils — Partie 2: Détermination de la précision et de la répétabilité de positionnement des axes en commande numérique — Rectificatif technique 1,1999-04-15,2,['25.040.20'],ISO/TC 39/SC 2,9599,,[35988],"['en','fr']",1,

35988,IS,,ISO 230-2:2006,Test code for machine tools — Part 2: Determination of accuracy and repeatability of positioning numerically controlled axes,Code d'essai des machines-outils — Partie 2: Détermination de l'exactitude et de la répétabilité de positionnement des axes en commande numérique,2006-03-17,3,"['25.040.20','25.080.01']",ISO/TC 39/SC 2,9599,"[26966,31798]",[55295],"['en','fr']",32,"<p>ISO 230-2-2:2006 specifies methods for testing and evaluating the accuracy and repeatability of the positioning of numerically controlled machine tool axes by direct measurement of individual axes on the machine. These methods apply equally to linear and rotary axes. When several axes are simultan

33836,IS,,ISO 230-3:2001,Test code for machine tools — Part 3: Determination of thermal effects,Code d'essai des machines-outils — Partie 3: Évaluation des effets thermiques,2001-03-08,1,['25.080.01'],ISO/TC 39/SC 2,9599,,[39188],"['en','fr']",35,

39188,IS,,ISO 230-3:2007,Test code for machine tools — Part 3: Determination of thermal effects,Code d'essai des machines-outils — Partie 3: Évaluation des effets thermiques,2007-08-06,2,['25.080.01'],ISO/TC 39/SC 2,9599,[33836],"[73291,60022]","['en','fr']",44,"<p>ISO 230-3:2007 defines three tests for the determination of thermal effects on machine tools: an environmental temperature variation error (ETVE) test, a test for thermal distortion caused by rotating spindles, and a test for thermal distortion caused by moving linear axes.</p><p>The test for thermal distortion caused by moving linear axes is applicable to numerically controlled (NC) machines only and is designed to quantify the e

4111,IS,,ISO 230-4:1996,Test code for machine tools — Part 4: Circular tests for numerically controlled machine tools,Code d'essai des machines-outils — Partie 4: Essais de circularité des machines-outils à commande numérique,1996-07-18,1,['25.040.20'],ISO/TC 39/SC 2,9599,,[36688],"['en','fr']",12,

36688,IS,,ISO 230-4:2005,Test code for machine tools — Part 4: Circular tests for numerically controlled machine tools,Code d'essai des machines-outils — Partie 4: Essais de circularité des machines-outils à commande numérique,2005-04-13,2,['25.040.20'],ISO/TC 39/SC 2,9599,[4111],[79155],"['en','fr']",17,"<p>ISO 230-4:2005 specifies methods of testing and evaluating the bi-directional circular deviation, the mean bi-directional radial deviation, the circular deviation and the radial deviation of circular paths that are produced by the simultaneous movements of two linear axes. Its objective is to provide a method for the measurement of the contouring performance of a numerically controlled m

35838,IS,,ISO 230-7:2006,Test code for machine tools — Part 7: Geometric accuracy of axes of rotation,Code d'essai des machines-outils — Partie 7: Exactitude géométrique des axes de rotation,2006-11-07,1,['25.080.01'],ISO/TC 39/SC 2,9599,,[56624],"['en','fr']",62,"<p>ISO 230-7:2006 is aimed at standardizing methods of specification and test of the geometric accuracy of axes of rotation used in machine tools. Spindles, rotary heads and rotary and swivelling tables of machine tools constitute axes of rotation, all having unintended motions in space as a result of multiple sources of errors. </p><p>ISO 230-7:2006 covers the following properties of spindles: axis of rotation error motion; speed

75196,IS,,ISO 23016-2:2019,Fine bubble technology — Agricultural applications — Part 2: Test method for evaluating the promotion of the germination of barley seeds,Technologie des fines bulles — Applications agricoles — Partie 2: Titre manque,2019-07-16,1,"['07.030','65.020.20']",ISO/TC 281,9599,,[91485],['en'],13,"<p>This document specifies a method to test the promotion of the germination of barley seeds, using ultrafine bubble (UFB) water produced from an ultrafine bubble water generating system. The performance of the method is assessed by measuring the ratio of barley seed germination.</p>"

7129,IS,,ISO 2302:1978,"Rubber, isobutene-isoprene (IIR) — Evaluation procedures",Caoutchouc isobutène-isoprène (IIR) — Méthodes d'évaluation,1978-11-01,2,['83.060'],ISO/TC 45,9599,,"[7130,7131]",['en'],3,

7130,IS,,ISO 2302:1985,"Rubber, isobutene-isoprene (IIR) — Evaluation procedures",Caoutchouc isobutène-isoprène (IIR) — Méthodes d'évaluation,1985-05-09,3,['83.060'],ISO/TC 45/SC 3,9599,[7129],[7131],"['en','fr']",3,

7131,IS,,ISO 2302:1995,Isobutene-isoprene rubber (IIR) — Evaluation procedures,Caoutchouc isobutène-isoprène (IIR) — Méthode d'évaluation,1995-12-21,4,['83.060'],ISO/TC 45/SC 3,9599,"[7130,7129]",[35177],"['en','fr']",7,"<p>Provides physical and chemical tests on raw rubber and specifies standard materials, standard test formulation and equipment for evaluating the vulcanization characteristics of isobutylene-isoprene rubber (IIR). Replaces the third edition which has been technically revised.</p>"

35177,IS,,ISO 2302:2005,Isobutene-isoprene rubber (IIR) — Evaluation procedures,Caoutchouc isobutène-isoprène (IIR) — Méthodes d'évaluation,2005-01-05,5,['83.060'],ISO/TC 45/SC 3,9599,[7131],[65596],['en'],10,"<p>ISO 2302:2005 specifies</p><ul><li>physical and chemical tests on raw rubbers;</li><li>standardized materials, a standardized test formulation, equipment and processing methods for evaluating the vulcanization characteristics of all types of isobutene-isoprene rubber (IIR).</li></ul><p>The precision data in ISO 2302:2005 have been taken, with permission of ASTM, from ASTM D 3188-95, <i>Standard Test Methods for Rubber -- Evaluation of IIR (Isobutene-Isoprene Rubber)</i>, copyright A

65596,IS,,ISO 2302:2014,Isobutene-isoprene rubber (IIR) — Evaluation procedure,Caoutchouc isobutène-isoprène (IIR) — Méthode d'évaluation,2014-10-15,6,['83.060'],ISO/TC 45/SC 3,9599,[35177],[80031],"['en','fr','ru']",11,"<p>ISO 2302:2014 specifies physical and chemical tests on raw rubbers and standardized materials, a standardized test formulation, equipment, and processing methods for evaluating the vulcanization characteristics of all types of isobutene-isoprene rubber (IIR).</p>"

7132,IS,,ISO 2303:1983,"Rubber, polyisoprene (IR) — Non-oil extended, solution-polymerized types — Test recipe and evaluation of vulcanization characteristics",Caoutchouc polyisoprène (IR) — Types polymérisés en solution et non étendus à l'huile — Formule d'essai et évaluation des caractéristiques de vulcanisation,1983-07-01,2,['83.060'],ISO/TC 45/SC 3,9599,,[7133],"['en','fr']",2,

7133,IS,,ISO 2303:1990,"Isoprene rubber (IR) — Non-oil-extended, solution-polymerized types — Evaluation procedure",Caoutchouc isoprène (IR) — Types polymérisés en solution et non étendus à l'huile — Méthode d'évaluation,1990-05-03,3,['83.060'],ISO/TC 45/SC 3,9599,[7132],[29382],"['en','fr']",3,"<p>Defines standard materials, equipment and processing methods for evaluating the vulcanization characteristics of polyisopren rubber. Replaces the first edition (ISO 2302-1975).</p>"

7134,IS,Amd,ISO 2303:1990/Amd 1:1993,"Isoprene rubber (IR) — Non-oil-extended, solution-polymerized types — Evaluation procedure — Amendment 1",Caoutchouc isoprène (IR) — Types polymérisés en solution et non étendus à l'huile — Méthode d'évaluation — Amendement 1,1993-11-04,3,['83.060'],ISO/TC 45/SC 3,9599,,[29382],"['en','fr']",3,"<p>Defines standard materials, equipment and processing methods for evaluating the vulcanization characteristics of polyisopren rubber.</p>"

29382,IS,,ISO 2303:2003,"Isoprene rubber (IR) — Non-oil-extended, solution-polymerized types — Evaluation procedure",Caoutchouc isoprène (IR) — Types polymérisés en solution et non étendus à l'huile — Méthode d'évaluation,2003-01-06,4,['83.060'],ISO/TC 45/SC 3,9599,"[7133,7134]",[52995],"['en','fr']",10,"<p>ISO 2303 specifies, for general purpose non-oil-extended, solution-polymerized rubbers (IR):</p><ul><li>physical and chemical tests on raw rubbers;</li><li>standard materials, standard test formulation, equipment and processing methods for evaluating the vulcanization characteristics.</li></ul><p>Two mill-mixing procedures are described in this Internatioanl Standard and an internal mixer

52995,IS,,ISO 2303:2011,"Isoprene rubber (IR) — Non-oil-extended, solution-polymerized types — Evaluation procedures",Caoutchouc isoprène (IR) — Types polymérisés en solution et non étendus à l'huile — Méthode d'évaluation,2011-08-12,5,['83.060'],ISO/TC 45/SC 3,9599,[29382],[75626],"['en','fr','ru']",14,"<p>ISO 2303:2011 specifies, for general-purpose non-oil-extended, solution-polymerized polyisoprene rubbers (IR):</p><ul><li>physical and chemical tests on raw rubbers;</li><li>standard materials, a standard test formulation, equipment and processing methods for evaluating the vulcanization characteristics.</li></ul>"

36600,IS,,ISO 23038:2006,Space systems — Space solar cells — Electron and proton irradiation test methods,Systèmes spatiaux — Cellules solaires spatiales — Méthodes d'essai d'irradiation d'électrons et de protons,2006-09-18,1,['49.140'],ISO/TC 20/SC 14,9599,,[69495],['en'],7,<p>ISO 23038:2006 specifies the requirements for electron and proton irradiation test methods of space solar cells. It addresses only test methods for performing electron and proton irradiation of space solar cells and not the method for data analysis.</p>

40367,IS,,ISO 23041:2007,Space systems — Unmanned spacecraft operational procedures — Documentation,Systèmes spatiaux — Procédures opérationnelles de véhicule spatial non habité — Documentation,2007-10-31,1,['49.140'],ISO/TC 20/SC 14,9599,,[73170],['en'],26,"<p>ISO 23041:2007 establishes standards, current guidelines and uniform procedures to minimize duplication of effort between the customer, the agency, participating nations and the emerging commercial space community. ISO 23041:2007 provides recommended practices for the development of space operations and support documentation, which should facilitate the sharing and exchange of beneficial information between organizations involved with

7136,IS,,ISO 2307:1972,Ropes — Determination of certain physical and mechanical properties,Cordages — Détermination de certaines caractéristiques physiques et mécaniques,1972-11-01,1,['59.080.50'],ISO/TC 38,9599,,[7137],"['en','fr']",7,

7138,IS,Amd,ISO 2307:1972/Amd 1:1974,Ropes — Determination of certain physical and mechanical properties — Amendment 1,Cordages — Détermination de certaines caractéristiques physiques et mécaniques — Amendement 1,1974-03-01,1,['59.080.50'],ISO/TC 38,9599,,[7137],['en'],2,

7137,IS,,ISO 2307:1990,Ropes — Determination of certain physical and mechanical properties,Cordages — Détermination de certaines caractéristiques physiques et mécaniques,1990-09-13,2,['59.080.50'],ISO/TC 38,9599,"[5682,7138,7136]",[36586],"['en','fr']",9,"<p>Specifies, for ropes of different kinds, a method of determining each of the following characteristics: net mass per metre; lay; elongation; tensile strength. This second edition cancels and replaces the first edition (1972) and ISO 1142:1973.</p>"

36586,IS,,ISO 2307:2005,Fibre ropes — Determination of certain physical and mechanical properties,Cordages en fibres — Détermination de certaines caractéristiques physiques et mécaniques,2005-02-22,3,['59.080.50'],ISO/TC 38,9599,[7137],[52347],"['en','fr']",17,"<p>ISO 2307:2004 specifies, for ropes of different kinds, a method of determining each of the following characteristics: linear density, lay length, braided pitch, elongation, and breaking force. The linear density, lay length and braided pitch are measured with the rope under a specified tension called the reference tension.</p><p>ISO 2307:2004 also provides a method for measuring water repellency, lubrication and finish content and

52347,IS,,ISO 2307:2010,Fibre ropes — Determination of certain physical and mechanical properties,Cordages en fibres — Détermination de certaines caractéristiques physiques et mécaniques,2010-07-30,4,['59.080.50'],ISO/TC 38,9599,[36586],[72076],"['en','fr']",16,"<p>ISO 2307:2010 specifies, for ropes of different kinds, a method of determining each of the following characteristics:</p><ul><li>linear density;</li><li>lay length;</li><li>braid pitch;</li><li>elongation;</li><li>breaking force.</li></ul><p>The linear density, lay length and braided pitch are measured with the rope under a specified tension called the reference tension.</p><p>The elongation corresponds to the measured increase in

40832,IS,,ISO 23081-1:2006,Information and documentation — Records management processes — Metadata for records — Part 1: Principles,Information et documentation — Processus de gestion des enregistrements — Métadonnées pour les enregistrements — Partie 1: Principes,2006-01-31,1,['01.140.20'],ISO/TC 46/SC 11,9599,[36627],[73172],"['en','fr','ru']",20,<p>ISO 23081-1:2006 covers the principles that underpin and govern records management metadata. These principles apply through time to:</p><ul><li> records and their metadata;</li><li> all processes that affect them;</li><li> any system in which they reside;</li><li> any organization that is responsible for their management.</li></ul>

50863,IS,,ISO 23081-2:2009,Information and documentation — Managing metadata for records — Part 2: Conceptual and implementation issues,Information et documentation — Gestion des métadonnées pour l'information et les documents — Partie 2: Concepts et mise en oeuvre,2009-06-30,1,['01.140.20'],ISO/TC 46/SC 11,9599,[43390],[81600],['en'],33,"<p>ISO/TS 23081-2:2009 establishes a framework for defining metadata elements consistent with the principles and implementation considerations outlined in ISO 23081-1:2006. The purpose of this framework is to:</p><ol><li>to enable standardized description of records and critical contextual entities for records,</li><li>to provide common understanding of fix

7141,IS,,ISO 2309:1980,Coke — Sampling,Coke — Échantillonnage,1980-02-01,2,['75.160.10'],ISO/TC 27/SC 4,9599,,[31776],"['en','fr']",23,"<p>Gives the practical directions for the sampling of metallurgical coke from which breeze has been removed, for the determination of any property for both routine and special purposes; the sampling of breeze, or small coke nominal top size 20 mm or less; preparation of a miosture sample and of a laboratory sample for the determination of ash and other properties.</p>"

7142,IS,,ISO 2311:1972,Electrolytic cathode copper,Cathodes en cuivre électrolytique,1972-10-01,1,['77.120.30'],ISO/TC 26,9599,,[4442],['en'],2,

41325,IS,,ISO 23125:2010,Machine tools — Safety — Turning machines,Machines-outils — Sécurité — Machines de tournage,2010-05-06,1,['25.080.01'],ISO/TC 39/SC 10,9599,,[65500],"['en','fr']",74,"<p>ISO 23125:2010 specifies the requirements and/or measures to eliminate the hazards or reduce the risks in the following groups of turning machines and turning centres, which are designed primarily to shape metal by cutting.</p><p>– Group 1: Manually controlled turning machines without numerical control.</p><p>– Group 2: Manually controlled turning machines with limited numerically controlled capability.</p><p>– Group 3: Numerically controlled turning machines and turning centres.</p><p>– Group 4: Sin

57038,IS,Amd,ISO 23125:2010/Amd 1:2012,Machine tools — Safety — Turning machines — Amendment 1,Machines-outils — Sécurité — Machines de tournage — Amendement 1,2012-03-28,1,['25.080.01'],ISO/TC 39/SC 10,9599,,[65500],"['en','fr']",12,

7144,IS,,ISO 2313:1972,Textiles — Determination of the recovery from creasing of a horizontally folded specimen of fabric by measuring the angle of recovery,"Étoffes — Détermination de l'auto- défroissabilité d'une éprouvette pliée horizontalement, par mesurage de l'angle rémanent après pliage",1972-11-01,1,['59.080.30'],ISO/TC 38/SC 24,9599,,"[77945,74898]","['en','fr']",4,<p>Creases in textile fabrics diminish at varying rates on the removal of the creasing forces. The magnitude of the crease recovery angle is an indication of the ability of a fabric to recover from accidental creasing. The results obtained by this method for textile fabrics of very different kinds cannot be compared direc

7145,IS,,ISO 2314:1973,Gas turbines — Acceptance tests,Turbines à gaz — Essais de réception,1973-03-01,1,['27.040'],ISO/TC 192,9599,,[7146],"['en','fr']",20,

7146,IS,,ISO 2314:1989,Gas turbines — Acceptance tests,Turbines à gaz — Essais de réception,1989-04-27,2,['27.040'],ISO/TC 192,9599,[7145],"[37981,42989]","['en','fr']",20,"<p>Specifies standard procedures and rules for the conduct and reporting of tests, defines standard conditions, applies to open cycle power plants and also includes closed cycle and semi-closed cycle power plants.</p>"

20752,IS,Amd,ISO 2314:1989/Amd 1:1997,Gas turbines — Acceptance tests — Amendment 1: for combined-cycle power plants,Turbines à gaz — Essais de réception — Amendement 1: pour des installations de puissance à cycle combiné,1997-11-27,2,['27.040'],ISO/TC 192,9599,,"[37981,42989]","['en','fr']",23,

29604,IS,Cor,ISO 2314:1989/Cor 1:1997,Gas turbines — Acceptance tests — Technical Corrigendum 1,Turbines à gaz — Essais de réception — Rectificatif technique 1,1997-11-27,2,['27.040'],ISO/TC 192,9599,,"[37981,42989]","['en','fr']",1,

41331,IS,,ISO 23146:2008,"Fine ceramics (advanced ceramics, advanced technical ceramics) — Test methods for fracture toughness of monolithic ceramics — Single-edge V-notch beam (SEVNB) method",Céramiques techniques — Méthodes d'essai pour la détermination de la ténacité à la rupture des céramiques monolithiques — Méthode sur éprouvette à entaille en V sur une seule face (Méthode SEVNB),2008-05-22,1,['81.060.30'],ISO/TC 206,9599,,[62093],['en'],16,"<p>ISO 23146:2008 specifies a method for the determination of the fracture toughness of advanced technical ceramics. The procedure makes use of single-edge V-notched bars, which are loaded in 4-point bending until failure. It is applicable to monol

74741,IS,,ISO 23150:2021,Road vehicles — Data communication between sensors and data fusion unit for automated driving functions — Logical interface,Véhicules routiers — Communication de données entre capteurs et unité de fusion de données pour les fonctions de conduite automatisée — Interface logique,2021-05-26,1,['43.040.15'],ISO/TC 22/SC 31,9599,,[83293],['en'],227,"<p>This document is applicable to road vehicles with automated driving functions. The document specifies the logical interface between in-vehicle environmental perception sensors (for example, radar, lidar, camera, ultrasonic) and the fusion unit which generates a surround model and interprets the scene around the vehicle base

83293,IS,,ISO 23150:2023,Road vehicles — Data communication between sensors and data fusion unit for automated driving functions — Logical interface,Véhicules routiers — Communication de données entre capteurs et unité de fusion de données pour les fonctions de conduite automatisée — Interface logique,2023-05-31,2,['43.040.15'],ISO/TC 22/SC 31,9599,[74741],"[87975,87976,87977,87963,87978,87964,87979,87971,87965,87972,87973,87974,87966,87968]",['en'],344,"<p class='MsoBodyText' style='mso-layout-grid-align: none; text-autospace: none;'><span lang='EN-GB' style='mso-bidi-font-size: 12.0pt;'>This document is applicable to road vehicles with automated driving functions. The document specifies th

7148,IS,,ISO 2316:1973,Withdrawal of ISO 2316-1973,Annulation de l'ISO 2316-1973,1973-02-01,1,['21.100.20'],ISO/TC 4,9599,,[4310],['en'],2,

53382,IS,,ISO 23161:2009,Soil quality — Determination of selected organotin compounds — Gas-chromatographic method,Qualité du sol — Dosage d'une sélection de composés organostanniques — Méthode par chromatographie en phase gazeuse,2009-08-19,1,['13.080.10'],ISO/TC 190/SC 3,9599,,[73990],"['en','fr']",37,"<p>ISO 23161:2009 specifies a gas-chromatographic method for the identification and quantification of organotin compounds (OTCs) in soils as specified in Table 1. The method is also applicable to samples from sediments, sludges and wastes (soil-like materials). The working range depends on the detection technique used and the amount of sample taken for analysis. The limit of quantification

7149,IS,,ISO 2320:1983,Prevailing torque type steel hexagon nuts — Mechanical and performance properties,"Écrous hexagonaux en acier, à freinage interne, à couple préalable — Caractéristiques mécaniques et performances",1983-08-01,2,['21.060.20'],ISO/TC 2,9599,,[7150],"['en','fr']",9,

7150,IS,,ISO 2320:1997,Prevailing torque type steel hexagon nuts — Mechanical and performance properties,Écrous hexagonaux autofreinés en acier — Caractéristiques mécaniques et performances,1997-10-30,3,['21.060.20'],ISO/TC 2,9599,[7149],[42184],"['en','fr']",20,

44739,IS,Cor,ISO 2320:1997/Cor 1:2006,Prevailing torque type steel hexagon nuts — Mechanical and performance properties — Technical Corrigendum 1,Écrous hexagonaux autofreinés en acier — Caractéristiques mécaniques et performances — Rectificatif technique 1,2006-08-24,3,['21.060.20'],ISO/TC 2,9599,,[42184],['en'],1,

42184,IS,,ISO 2320:2008,Prevailing torque type steel nuts — Mechanical and performance properties,Écrous autofreinés en acier — Caractéristiques mécaniques et performances,2008-10-23,4,['21.060.20'],ISO/TC 2/SC 12,9599,"[7150,44739]",[61175],"['en','fr']",19,"<p>ISO 2320:2008 specifies the mechanical and performance properties for prevailing torque type steel nuts when tested at an ambient temperature range of +10 °C to +35 °C. It includes a single test to determine the prevailing torque properties (performance properties) and/or the torque/clamp force properties.</p><p>ISO 2320:2008 applies to prevailing torque all metal type nuts and prevailing torque non-metallic insert type nuts: a) with

36735,IS,,ISO 23205:2006,Agricultural tractors — Instructional seat,Tracteurs agricoles — Siège de convoyeur,2006-08-14,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[62662],"['en','fr']",4,"<p>ISO 23205:2006 specifies the minimum design and performance requirements for an instructional seat and restraint designed for limited use by a trainer, trainee or service person inside the enclosed cab of an agricultural tractor.</p>"

36748,IS,,ISO 23208:2005,Cryogenic vessels — Cleanliness for cryogenic service,Récipients cryogéniques — Propreté en service cryogénique,2005-02-18,1,['23.020.40'],ISO/TC 220,9599,,[65989],['en'],8,<p>ISO 23208:2005 specifies the minimum requirements for the cleanliness of all surfaces of cryogenic vessels and associated accessories that are in contact with the cryogenic fluid at any expected operating conditions.</p><p>ISO 23208:2005 defines the acceptable level of surface and particle contamination to minimize the risk of malfunction of equipment and ensure safety against ignition when in contact with oxygen or oxidizing fluids (see ISO 10156-2).</p>

7151,IS,,ISO 2321:1983,Rubber threads — Methods of test,Fils élastiques — Méthodes d'essai,1983-11-01,2,['83.140.99'],ISO/TC 45/SC 4,9599,,"[40108,27012]","['en','fr']",18,"<p>Specifies methods of test for determining certain physical and mechanical properties. Owing to the comparatively small cross-section and unusual conditions of performance of this material, special methods have been developed. Some of the tests may not be entirely suitable for thread made from certain synthetic rubbers. Comparisons may only be made on new rubber threads or on that with identical processing histories. The previous history shall be stated in the test report. Replaces the first edition (ISO 2321-1975)</p>"

40108,IS,,ISO 2321:2006,Rubber threads — Methods of test,Fils élastiques — Méthodes d'essai,2006-11-22,3,['83.140.99'],ISO/TC 45/SC 4,9599,[7151],[68003],['en'],26,"<p>ISO 2321:2006 specifies methods of test for determining general physical and mechanical properties of rubber threads, as well as specific mechanical properties of such threads in contact with fabrics. Owing to the comparatively small cross-section and the unusual conditions of service of this material, certain special methods have been developed.</p><p>Some of the tests included in this International Standard may not be entirely suitable for threads made from certain synthetic rubbers (e.g. urethane rubber). These tests are in

7152,IS,,ISO 2322:1981,"Rubber, raw styrene-butadiene, emulsion polymerized — Test recipe and method of evaluation","Caoutchouc, butadiène-styrène brut, polymérisé en émulsion — Formule d'essai et méthode d'évaluation",1981-11-01,2,['83.040.10'],ISO/TC 45,9599,,"[7155,7153]","['en','fr']",2,

7156,IS,Amd,ISO 2322:1981/Amd 1:1993,"Rubber, raw styrene-butadiene, emulsion polymerized — Test recipe and method of evaluation — Amendment 1","Caoutchouc, butadiène-styrène brut, polymérisé en émulsion — Formule d'essai et méthode d'évaluation — Amendement 1",1993-01-21,2,['83.060'],ISO/TC 45/SC 3,9599,,"[7155,7153]","['en','fr']",4,

7153,IS,,ISO 2322:1985,"Rubber, styrene-butadiene (SBR, YSBR) — Emulsion and solution-polymerized types — Test recipes and evaluation of vulcanization characteristics","Caoutchoucs butadiène-styrène (SBR, YSBR) — Types polymérisés en émulsion et en solution — Formules d'essai et évaluation des caractéristiques de vulcanisation",1985-10-17,3,['83.060'],ISO/TC 45/SC 3,9599,"[7152,7156]",[7155],"['en','fr']",3,

7155,IS,,ISO 2322:1996,Styrene-butadiene rubber (SBR) — Emulsion- and solution-polymerized types — Evaluation procedures,Caoutchouc butadiène-styrène (SBR) — Types polymérisés en émulsion et en solution — Méthode d'évaluation,1996-11-07,4,['83.060'],ISO/TC 45/SC 3,9599,"[7152,7156,7153]",[44287],"['en','fr']",13,"<p>Describes physical and chemical tests on raw rubbers and specifies standard materials, standard test formulations, equipment and processing methods for evaluating the vulcanization characteristics of styrene-butadiene rubber (SBR), including oil-extended types. Replaces the third edition.</p>"

44287,IS,,ISO 2322:2009,Styrene-butadiene rubber (SBR) — Emulsion- and solution-polymerized types — Evaluation procedures,Caoutchouc butadiène-styrène (SBR) — Types polymérisés en émulsion et en solution — Méthode d'évaluation,2009-09-01,5,['83.060'],ISO/TC 45/SC 3,9599,[7155],[61315],"['en','fr','ru']",16,"<p>ISO 2322:2009 specifies:</p><ul><li>physical and chemical tests on raw rubbers;</li><li>standard materials, standard test formulations, equipment and processing methods for evaluating the vulcanization characteristics of emulsion- and solution-polymerized styrene-butadiene rubbers (SBR), including oil-extended rubbers.</li></ul>"

61315,IS,,ISO 2322:2014,Styrene-butadiene rubber (SBR) — Emulsion- and solution-polymerized types — Evaluation procedures,Caoutchouc butadiène-styrène (SBR) — Types polymérisés en émulsion et en solution — Méthode d'évaluation,2014-02-11,6,['83.060'],ISO/TC 45/SC 3,9599,[44287],[81598],"['en','fr']",16,"<p>ISO 2322:2014 specifies:</p><p>- physical and chemical tests on raw rubbers;</p><p>- standard materials, standard test formulations, equipment, and processing methods for evaluating the vulcanization characteristics of emulsion- and solution-polymerized styrene-butadiene rubbers (SBR), including oil-extended rubbers.</p>"

74917,IS,,ISO 23223:2021,Alpine ski boots with improved walking soles — Interface with alpine ski-bindings – Requirements and test methods,Chaussures de ski pour skis alpins dotées de semelles de marche améliorées — Zone de contact avec les fixations de ski alpin — Exigences et méthodes d’essai,2021-07-08,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[88021],"['en','fr']",42,"<p>This document specifies requirements, test methods and marking for alpine ski-boots with improved walking soles that are used with systems of alpine ski-bindings for improved walking soles with attachment at the boot front and boot rear, the proper release function of which depends on the dimensions and design of the interfac

41398,IS,,ISO 23231:2008,Textiles — Determination of dimensional change of fabrics — Accelerated machine method,Textiles — Détermination des variations dimensionnelles des étoffes — Méthode machine accélérée,2008-08-26,1,['59.080.30'],ISO/TC 38/SC 2,9599,,[88348],"['en','fr']",8,"<p>ISO 23231:2008 specifies a test method for an accelerated procedure for determination of the dimensional change of fabrics which will then be made into garments or other end-use articles that will be laundered in a variety of settings. The procedure uses an apparatus with programmable settings that simulate multiple domestic or industrial laundering actions as well as wet processing operations in fabric manufactu

41402,IS,,ISO 23233:2009,"Rubber, vulcanized or thermoplastic — Determination of resistance to abrasion using a driven, vertical abrasive disc","Caoutchouc, vulcanisé ou thermoplastique — Détermination de la résistance à l'abrasion au moyen d'un disque abrasif vertical, motorisé",2009-02-16,1,['83.060'],ISO/TC 45/SC 2,9599,,[68113],"['en','fr']",11,"<p>ISO 23233:2009 specifies a method for the determination of the resistance of rubber to abrasion using a driven, vertical abrasive disc (the LAT 100: Laboratory Abrasion Tester 100).</p><p>The loss in mass on abrasion is determined through the slip caused by setting different slip angles and rotational speeds between a wheel-shaped rubber test

7157,IS,,ISO 2324:1972,Withdrawal of ISO 2324-1972,Annulation de l'ISO 2324-1972,1972-10-01,1,['25.100.20'],ISO/TC 29,9599,,[6260],"['en','fr']",4,

7158,IS,,ISO 2325:1979,Coke — Size analysis (Nominal top size 20 mm or less),Coke — Analyse granulométrique (Dimension supérieure nominale égale ou inférieure à 20 mm),1979-02-01,2,['75.160.10'],ISO/TC 27,9599,,[7159],"['en','fr']",3,

7159,IS,,ISO 2325:1986,Coke — Size analysis (Nominal top size 20 mm or less),Coke — Analyse granulométrique (Dimension nominale égale ou inférieure à 20 mm),1986-02-13,3,['75.160.10'],ISO/TC 27/SC 3,9599,[7158],[78696],"['en','fr']",3,"<p>Two methods of operation are described: where a restricted size analysis is required, using two sieves only; where a complete size analysis is required. A sample of coke is subjected to a prozess of size analysis by a specified procedure, and the results are expressed in terms of the cumulative percentage by mass of the coke remaining on sieves of different sized openings.</p>"

41414,IS,,ISO 23251:2006,"Petroleum, petrochemical and natural gas industries — Pressure-relieving and depressuring systems","Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes de dépressurisation et de protection contre les surpressions",2006-08-14,1,['75.180.20'],ISO/TC 67/SC 6,9599,,"[55619,75144]","['en','fr']",192,"<p>ISO 23251:2006 is applicable to pressure-relieving and vapour-depressuring systems. Although intended for use primarily in oil refineries, it is also applicable to petrochemical facilities, gas plants, liquefied natural gas (LNG) facilities and oil and gas production facilities. The information provided is designed to aid in the selection of the system t

50589,IS,Amd,ISO 23251:2006/Amd 1:2008,"Petroleum, petrochemical and natural gas industries — Pressure-relieving and depressuring systems — Amendment 1","Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes de dépressurisation et de protection contre les surpressions — Amendement 1",2008-05-15,1,['75.180.20'],ISO/TC 67/SC 6,9599,,[75144],"['en','fr']",7,

46567,IS,Cor,ISO 23251:2006/Cor 1:2007,"Petroleum, petrochemical and natural gas industries — Pressure-relieving and depressuring systems — Technical Corrigendum 1","Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes de dépressurisation et de protection contre les surpressions — Rectificatif technique 1",2007-08-17,1,['75.180.20'],ISO/TC 67/SC 6,9599,,[75144],['en'],3,

41416,IS,,ISO 23273-2:2006,Fuel cell road vehicles — Safety specifications — Part 2: Protection against hydrogen hazards for vehicles fuelled with compressed hydrogen,Véhicules routiers alimentés par pile à combustible — Spécifications de sécurité — Partie 2: Protection contre les dangers de l'hydrogène pour les véhicules utilisant de l'hydrogène comprimé,2006-05-17,1,['43.120'],ISO/TC 22,9599,,"[64047,61623]",['en'],6,"<p>ISO 23273-2:2006 specifies the essential requirements for fuel cell vehicles (FCV) with respect to the protection of persons and the environment inside and outside the vehicle against hydrogen related hazards.</p><p>It applies only to such FCV where compressed hydrogen is

57048,IS,,ISO 23274-1:2013,Hybrid-electric road vehicles — Exhaust emissions and fuel consumption measurements — Part 1: Non-externally chargeable vehicles,Véhicules routiers électriques hybrides — Mesurages des émissions à l'échappement et de la consommation de carburant — Partie 1: Véhicules non rechargeables par des moyens externes,2013-01-08,1,['43.120'],ISO/TC 22/SC 37,9599,[41418],[76737],['en'],27,"<p>ISO 23274-1:2013 specifies a chassis dynamometer test procedure to measure the exhaust emissions and the electric energy and fuel consumption for the vehicles.</p><p>It applies to vehicles with the following characteristics:</p><ul><li>the vehicle is classified as passenger cars or light

54848,IS,,ISO 23274-2:2012,Hybrid-electric road vehicles — Exhaust emissions and fuel consumption measurements — Part 2: Externally chargeable vehicles,Véhicules routiers électriques hybrides — Mesurages des émissions à l'échappement et de la consommation de carburant — Partie 2: Véhicules rechargeables par des moyens externes,2012-07-26,1,['43.120'],ISO/TC 22/SC 37,9599,[41418],[78417],['en'],34,"<p>ISO 23274-2:2012 specifies a chassis dynamometer test procedure to determine the end of CD (charge-depleting) state and consumed electric energy during CD state.</p><p>The identification of the end of CD state is an important step for procedures to determine exhaust emissions and fuel consumptio

41418,IS,,ISO 23274:2007,Hybrid-electric road vehicles — Exhaust emissions and fuel consumption measurements — Non-externally chargeable vehicles,Véhicules routiers électriques hybrides — Mesurages des émissions à l'échappement et de la consomation de carburant — Véhicules non rechargeables par des moyens externes,2007-06-06,1,['43.120'],ISO/TC 22,9599,,"[54848,57048]",['en'],38,"<p>ISO 23274:2007 establishes a uniform chassis dynamometer test procedure for hybrid-electric road vehicles (HEV) with internal combustion engines (ICE) classified as passenger cars and light duty trucks, as defined in each regional annex. ISO 23274:2007 proposes ways of correcting the measured emissions and fuel c

41428,IS,,ISO 23277:2006,Non-destructive testing of welds — Penetrant testing of welds — Acceptance levels,Contrôle non destructif des assemblages soudés — Contrôle par ressuage des soudures — Niveaux d'acceptation,2006-10-02,1,['25.160.40'],ISO/TC 44/SC 5,9599,,[62315],"['en','fr','ru']",4,"<p>ISO 23277:2006 specifies acceptance levels for indications from surface breaking imperfections in metallic welds detected by penetrant testing.</p><p>The acceptance levels in ISO 23277:2006 are primarily intended for use during manufacture examination, but where appropriate they can be used for in-service inspection.</p><p>These acceptance levels can be related to welding standards, application standa

41429,IS,,ISO 23278:2006,Non-destructive testing of welds — Magnetic particle testing of welds — Acceptance levels,Contrôle non destructif des assemblages soudés — Contrôle par magnétoscopie des soudures — Niveaux d'acceptation,2006-09-29,1,['25.160.40'],ISO/TC 44/SC 5,9599,,[62316],"['en','fr']",3,"<p>ISO 23278:2006 specifies acceptance levels for indications from imperfections in ferromagnetic steel welds detected by magnetic particle testing.</p><p>The acceptance levels in ISO 23278:2006 are primarily intended for use during manufacture examination, but where appropriate they can be used for in-service inspection.</p><p>These acceptance levels can be related to welding standards, applicat

41430,IS,,ISO 23279:2007,Non-destructive testing of welds — Ultrasonic testing — Characterization of indications in welds,Contrôle non destructif des assemblages soudés — Contrôle par ultrasons — Caractérisation des indications dans les assemblages soudés,2007-03-08,1,['25.160.40'],ISO/TC 44/SC 5,9599,"[41438,41439]",[50440],['en'],15,<p>ISO 23279:2007 defines a procedure for classifying internal indications as planar or non-planar.</p><p>This procedure is only suitable for indications located at least 5 mm below the unground surface of the joint.</p>

50440,IS,,ISO 23279:2010,Non-destructive testing of welds — Ultrasonic testing — Characterization of indications in welds,Contrôle non destructif des assemblages soudés — Contrôle par ultrasons — Caractérisation des indications dans les assemblages soudés,2010-02-24,2,['25.160.40'],ISO/TC 44/SC 5,9599,[41430],[69612],"['en','fr']",14,<p>ISO 23279:2010 specfies how to characterize embedded indications by classifying them as planar or non-planar.</p><p>This procedure is also suitable for indications that break the surface after removal of the weld reinforcement.</p>

7162,IS,,ISO 2328:1977,Fork lift trucks — Hook-on type fork arms and fork carriers — Mounting dimensions,Chariots élévateurs à fourche — Bras de fourche à tenons et tabliers porte- équipements — Dimensions de montage,1977-10-01,1,['53.060'],ISO/TC 110,9599,,[1211],"['en','fr']",4,

1211,IS,,ISO 2328:1993,Fork-lift trucks — Hook-on type fork arms and fork arm carriages — Mounting dimensions,Chariots élévateurs à fourche — Bras de fourche à tenons et tabliers porte-équipements — Dimensions de montage,1993-10-28,2,['53.060'],ISO/TC 110/SC 2,9599,[7162],"[39355,41664]","['en','fr']",3,"<p>Specifies the mounting dimensions and some additional requirements to permit interchangeability of fork arms and/or other attachments, related to the truck rated capacity and type of fork arm.</p>"

41664,IS,,ISO 2328:2007,Fork-lift trucks — Hook-on type fork arms and fork arm carriages — Mounting dimensions,Chariots élévateurs à fourche — Bras de fourche à tenons et tabliers porte-fourches — Dimensions de montage,2007-05-16,3,['53.060'],ISO/TC 110/SC 2,9599,[1211],[51106],"['en','fr']",5,"<p>ISO 2328:2007 specifies the dimensions of, and additional requirements for, fork carriers and hook-on type fork arms, to permit the interchangeability of these fork arms and/or other attachments, relative to the truck-rated capacity and fork arm type, on fork-lift trucks up to and including 10 999 kg.</p>"

75166,IS,,ISO 23296:2022,Metallic materials – Fatigue testing – Force controlled thermo-mechanical fatigue testing method,Matériaux métalliques – Essai de fatigue – Méthode d'essai de fatigue thermomécanique à force contrôlée,2022-01-05,1,['77.040.10'],ISO/TC 164/SC 4,9599,,[85732],['en'],30,"<p>This document applies to stress and/or force-controlled thermo-mechanical fatigue (TMF) testing. Both forms of control, force or stress, can be applied according to this document. This document describes the equipment, specimen preparation, and presentation of the test results in order to determine TMF properties.</p>"

41444,IS,,ISO 23297:2008,Thermoplastics hoses and hose assemblies — Wire or synthetic yarn reinforced single-pressure types for hydraulic applications — Specification,"Tuyaux et flexibles en matière thermoplastique — Types hydrauliques à pression unique, avec armature de fils métalliques ou synthétiques — Spécifications",2008-12-01,1,"['23.100.40','83.140.40']",ISO/TC 45/SC 1,9599,,[72844],['en'],14,"<p>ISO 23297:2008 specifies requirements for eight classes and two types (construction with adhesive bond between layers and construction without adhesive bond between layers) of wire or synthetic yarn reinforced hydraulic hoses and hose assemblies of nominal size from 3,2 to 31,5. Each class ha

2398,IS,,ISO 233-3:1999,Information and documentation — Transliteration of Arabic characters into Latin characters — Part 3: Persian language — Simplified transliteration,Information et documentation — Translittération des caractères arabes en caractères latins — Partie 3: Persan — Translittération simplifiée,1999-01-21,1,['01.140.10'],ISO/TC 46,9599,,[78514],['en'],11,"<p>This part of ISO 233 establishes a simplified system for the transliteration of Persian characters into Latin</p><p>characters. This simplification of the stringent rules established by ISO 233:1984 is especially intended to facilitate</p><p>the processing of bibliographic information (e.g. catalogues, indices, citations,

7165,IS,,ISO 2330:1974,Fork lift trucks — Fork arms — Technical characteristics and testing,Chariots élévateurs à fourche — Bras de fourche — Caractéristiques techniques et essais,1974-08-01,1,['53.060'],ISO/TC 110,9599,,[1373],"['en','fr']",2,

1373,IS,,ISO 2330:1995,Fork-lift trucks — Fork arms — Technical characteristics and testing,Chariots élévateurs à fourches — Bras de fourche — Caractéristiques techniques et essais,1995-06-22,2,['53.060'],ISO/TC 110/SC 2,9599,[7165],[36156],"['en','fr']",3,"<p>Cancels and replaces the first edition (1974). Specifies manufacturing, testing and marking requirements for solid section fork arms, for quantity production and with all types of mounting. By agreement between the fork arm manufacturer and the purchaser, these requirements may also be applied to fork arms intended for quantity manufacture.</p>"

75204,IS,,ISO 23308-1:2020,Energy efficiency of industrial trucks — Test methods — Part 1: General,Efficacité énergétique des chariots de manutention — Méthodes d'essai — Partie 1: Généralités,2020-05-29,1,['53.060'],ISO/TC 110/SC 5,9599,,[85857],['en'],20,"<p>This document specifies general test criteria and requirements to measure the energy consumption for self-propelled industrial trucks (hereinafter referred to as trucks) during operation. For electric trucks, the efficiency of the battery and the battery charger is included.</p><p>The truck specific requirements in ISO 23308‑2 and ISO 23308‑3 take precedence over the respective requirements of ISO 23308‑1.</p><p>This document is applic

75214,IS,,ISO 23308-2:2020,"Energy efficiency of industrial trucks — Test methods — Part 2: Operator controlled self propelled trucks, towing and burden carrier trucks","Efficacité énergétique des chariots de manutention — Méthodes d'essai — Partie 2: Chariots automoteurs commandés par l'opérateur, tracteurs et chariots transporteurs de charge",2020-05-29,1,['53.060'],ISO/TC 110/SC 5,9599,,[85858],['en'],7,"<p>This document specifies the method of energy consumption measurement for the following types of industrial trucks as defined in ISO 5053‑1:</p><p>— counterbalance lift truck;</p><p>— articulated counterbalance lift truck;</p><p>— reach truck (with retractable mast or fork a

75216,IS,,ISO 23308-3:2020,Energy efficiency of industrial trucks — Test methods — Part 3: Container handling lift trucks,Efficacité énergétique des chariots de manutention — Méthodes d'essai — Partie 3: Chariots élévateurs porte-conteneur,2020-05-29,1,['53.060'],ISO/TC 110/SC 5,9599,,[85859],['en'],4,"<p>This document specifies the method of energy consumption measurement for container handling lift trucks, as defined in ISO 5053‑1.</p>"

36799,IS,,ISO 23309:2007,Hydraulic fluid power systems — Assembled systems — Methods of cleaning lines by flushing,Transmissions hydrauliques — Systèmes assemblés — Méthodes de nettoyage des canalisations par curage,2007-05-18,1,['23.100.40'],ISO/TC 131/SC 6,9599,,"[74772,61866]","['en','fr']",7,"<p>ISO 23309:2007 specifies the procedures for flushing from the hydraulic lines of larger hydraulic fluid power systems solid particulate contamination that can be introduced during the initial build of a new hydraulic system or after maintenance or modification of an existing system.</p><p>ISO 23309:2007 supplements, but does not replace, the requirements of the component supplier and customer, es

41446,IS,,ISO 23317:2007,Implants for surgery — In vitro evaluation for apatite-forming ability of implant materials,Implants chirurgicaux — Évaluation in vitro de la capacité de formation d'apatite des matériaux d'implants,2007-06-12,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[54163],"['en','ru']",13,<p>ISO 23317:2007 describes the method for detecting apatite formed on a surface of a material in simulated body fluid (SBF).</p>

54163,IS,,ISO 23317:2012,Implants for surgery — In vitro evaluation for apatite-forming ability of implant materials,Implants chirurgicaux — Évaluation in vitro de la capacité de formation d'apatite des matériaux d'implants,2012-09-28,2,['11.040.40'],ISO/TC 150/SC 1,9599,[41446],[65054],['en'],13,<p>ISO 23317:2012 specifies a method for detecting apatite formed on a surface of a material in simulated body fluid (SBF). It is applicable to implant surfaces intended to come into direct bone contact.</p>

65054,IS,,ISO 23317:2014,Implants for surgery — In vitro evaluation for apatite-forming ability of implant materials,Implants chirurgicaux — Évaluation in vitro de la capacité de formation d'apatite des matériaux d'implants,2014-06-13,3,['11.040.40'],ISO/TC 150/SC 1,9599,[54163],[82119],['en'],13,<p>ISO 23317:2014 specifies a method for detecting apatite formed on a surface of a material in simulated body fluid (SBF). It is applicable to implant surfaces intended to come into direct bone contact.</p>

7167,IS,,ISO 2332:1983,Agricultural tractors and machinery — Connections — Clearance zone for the three-point linkage of implements,Tracteurs et matériels agricoles — Liaisons — Zone de dégagement pour les attelages trois points des instruments,1983-12-01,1,['65.060'],ISO/TC 23/SC 4,9599,,[7154],"['en','fr']",3,