Withdrawn and superseded ISO standards — page 80 of 246

39350,IS,,ISO 22442-2:2007,"Medical devices utilizing animal tissues and their derivatives — Part 2: Controls on sourcing, collection and handling","Dispositifs médicaux utilisant des tissus animaux et leurs dérivés — Partie 2: Contrôles de l'origine, de la collecte et du traitement",2007-11-27,1,['11.100.20'],ISO/TC 194,9599,,[68554],"['en','fr','ru']",16,"<p>ISO 22442-2:2007 specifies requirements for controls on the sourcing, collection and handling (which includes storage and transport) of animals and tissues for the manufacture of medical devices utilizing materials of animal origin, other than <i>in vitro</i> diagnostic medical devices. It applies where required by the risk management

68554,IS,,ISO 22442-2:2015,"Medical devices utilizing animal tissues and their derivatives — Part 2: Controls on sourcing, collection and handling","Dispositifs médicaux utilisant des tissus animaux et leurs dérivés — Partie 2: Contrôles de l'origine, de la collecte et du traitement",2015-11-02,2,['11.100.20'],ISO/TC 194,9599,[39350],[74281],"['en','fr']",15,"<p>ISO 22442-2:2015 specifies requirements for controls on the sourcing, collection, and handling (which includes storage and transport) of animals and tissues for the manufacture of medical devices utilizing materials of animal origin other than in vitro diagnostic medical devices. It applies where required by the risk management proce

7056,IS,,ISO 2245:1972,Shaped insulating refractory products — Classification,Produits réfractaires isolants façonnés — Classification,1972-06-01,1,['81.080'],ISO/TC 33,9599,,[7057],"['en','fr']",2,

7057,IS,,ISO 2245:1990,Shaped insulating refractory products — Classification,Produits réfractaires isolants façonnés — Classification,1990-12-06,2,['81.080'],ISO/TC 33,9599,[7056],"[38367,26564]","['en','fr']",2,<p>Establishes a classification of shaped insulating refractory products based on the determination of permanent change in dimensions (ISO 2477) Does not apply to products composed mainly of fibres.</p>

73268,IS,,ISO 22459:2020,"Fine ceramics (advanced ceramics, advanced technical ceramics) — Reinforcement of ceramic composites — Determination of distribution of tensile strength and tensile strain to failure of filaments within a multifilament tow at ambient temperature",Céramiques techniques — Renfort de céramiques composites — Détermination de la distribution de la résistance en traction et de la déformation à la rupture en traction de filaments dans un fil multifilamentaire à température ambiante,2020-06-10,1,['81.060.30'],ISO/TC 206,9599,,[88424],"['en','fr']",17,<p>This document specifies the conditions for the determination of the distribution of strength and rupture strain of ceramic

7059,IS,,ISO 2247-1:1972,"Packaging — Complete, filled transport packages — Part 1: Vibration test",Emballages — Emballages d'expédition complets et pleins — Partie 1: Essai de vibration,1972-04-01,1,['55.180.40'],ISO/TC 122,9599,,[7060],['en'],2,

7060,IS,,ISO 2247:1985,"Packaging — Complete, filled transport packages — Vibration test at fixed low frequency",Emballages — Emballages d'expédition complets et pleins — Essai de vibration à basse fréquence fixe,1985-12-05,2,['55.180.40'],ISO/TC 122/SC 3,9599,[7059],[32412],"['en','fr']",2,

40970,IS,,ISO 22472:2006,Ships and marine technology — Guidelines for the operation and installation of voyage data recorders (VDR),Navires et technologie maritime — Lignes directrices pour le fonctionnement et l'installation des enregistreurs de données de voyage (VDR),2006-10-30,1,['47.040'],ISO/TC 8/SC 6,9599,,[66209],"['en','ru']",57,"<p>ISO 22472:2006 provides guidance for the planning, installation and operational testing of voyage data recorder (VDR) and simplified voyage data recorder (S-VDR) installations according to the electric/electronic and acoustic specifications of IMO A.861 (20), IMO MSC.163 (78) and IEC 61996 (including IEC 61996-2, Simplified voyage data recorder). These s

36244,IS,,ISO 22475-1:2006,Geotechnical investigation and testing — Sampling methods and groundwater measurements — Part 1: Technical principles for execution,Reconnaissance et essais géotechniques — Méthodes de prélèvement et mesurages piézométriques — Partie 1: Principes techniques des travaux,2006-09-14,1,['93.020'],ISO/TC 182,9599,,[71002],"['en','fr']",120,"<p>ISO 22475-1:2006 deals with the technical principles of sampling soil, rock and groundwater, and with groundwater measurements, in the context of geotechnical investigation and testing, as described in EN 1997-1 and EN 1997-2. </p>"

57728,IS,,ISO 22476-1:2012,Geotechnical investigation and testing — Field testing — Part 1: Electrical cone and piezocone penetration test,Reconnaissance et essais géotechniques — Essais en place — Partie 1: Essais de pénétration au cône électrique et au piézocône,2012-09-18,1,['93.020'],ISO/TC 182,9599,,[75661],"['en','fr']",36,"<p>ISO 22476-1:2012 deals with equipment requirements, the execution of and reporting on electrical cone and piezocone penetration tests as part of geotechnical investigation and testing according to EN 1997‑1 and EN 1997‑2.</p><p>Within the electrical cone and piezocone penetration test, two subcategories of the cone penetration test are considered:</p><ul><li>elec

63259,IS,Cor,ISO 22476-1:2012/Cor 1:2013,Geotechnical investigation and testing — Field testing — Part 1: Electrical cone and piezocone penetration test — Technical Corrigendum 1,Reconnaissance et essais géotechniques — Essais en place — Partie 1: Essais de pénétration au cône électrique et au piézocône — Rectificatif technique 1,2013-01-03,1,['93.020'],ISO/TC 182,9599,,[75661],"['en','fr']",36,

57729,IS,,ISO 22476-4:2012,Geotechnical investigation and testing — Field testing — Part 4: Ménard pressuremeter test,Reconnaissance et essais géotechniques — Essais en place — Partie 4: Essai au pressiomètre Ménard,2012-11-27,1,['93.020'],ISO/TC 182,9599,,[75662],"['en','fr']",51,

57730,IS,,ISO 22476-5:2012,Geotechnical investigation and testing — Field testing — Part 5: Flexible dilatometer test,Reconnaissance et essais géotechniques — Essais en place — Partie 5: Essai au dilatomètre flexible,2012-11-28,1,['93.020'],ISO/TC 182,9599,,[75663],"['en','fr']",31,"<p>ISO 22476-5:2012 specifies the equipment requirements, execution of and reporting on flexible dilatometer tests.</p><p>ISO 22476-5:2012 is applicable to tests in ground stiff enough not to be adversely affected by the drilling operation.</p><p>ISO 22476-5:2012 is applicable to four procedures for conducting a test with the flexible dilatometer.</p><p>ISO 22476-5:2012 applies to tests performed up to 1 800 m de

7061,IS,,ISO 2248-1:1972,"Packaging — Complete, filled transport packages — Part 1: Vertical impact test by dropping",Emballages — Emballages d'expédition complets et pleins — Partie 1: Essais de choc vertical par chute libre,1972-05-01,1,['55.180.40'],ISO/TC 122,9599,,[7062],['en'],3,

40202,IS,,ISO 22489:2006,Microbeam analysis — Electron probe microanalysis — Quantitative point analysis for bulk specimens using wavelength-dispersive X-ray spectroscopy,Analyse par microfaisceaux — Analyse par microsonde de Castaing — Analyse quantitative ponctuelle d'échantillons massifs par spectrométrie X à dispersion de longueur d'onde,2006-12-12,1,['71.040.99'],ISO/TC 202/SC 2,9599,,[70288],"['en','fr']",14,"<p>ISO 22489:2006 specifies requirements for the quantification of elements in a micrometre-sized volume of a specimen identified through analysis of the X-rays generated by an electron beam using wavelength-dispersive spectrometers fitted either to an electron probe microanalyser

40975,IS,,ISO 22493:2008,Microbeam analysis — Scanning electron microscopy — Vocabulary,Analyse par microfaisceaux — Microscopie électronique à balayage — Vocabulaire,2008-09-19,1,"['37.020','01.040.37']",ISO/TC 202/SC 1,9599,,[64932],"['en','fr']",22,"<p>ISO 22493:2008 defines terms used in the practice of scanning electron microscopy (SEM). It covers both general and specific concepts classified according to their hierarchy in a systematic order, with those terms that have already been defined in ISO 23833 also included, where appropriate.</p><p>The vocabulary is applicable to all standardization documents relevant to the practice of SEM. In addition, some clauses of the vocabulary are app

4098,IS,,ISO 225:1983,"Fasteners — Bolts, screws, studs and nuts — Symbols and designations of dimensions","Éléments de fixation — Vis, goujons et écrous — Symboles et désignations des dimensions",1983-11-01,2,['21.060.10'],ISO/TC 2/SC 7,9599,,"[41052,32357,45872]","['en','fr','ru']",19,"<p>Lays down the method of dimensioning bolts, screws, studs and nuts; includes common symbols and describes the features; in addition to terms in the official ISO languages English, French, and Russian it gives the equivalent terms in German, Italian and Spanish.</p>"

7064,IS,,ISO 2250:1972,"Finishing reamers for morse and metric tapers, with parallel shanks and morse taper shanks","Alésoirs de finition pour cônes Morse et métrique, à queue cylindrique et à queue cône Morse",1972-05-01,1,['25.100.30'],ISO/TC 29/SC 9,9599,,[50891],"['en','fr']",3,

50891,IS,,ISO 2250:2009,"Finishing reamers for Morse and metric tapers, with cylindrical shanks and Morse taper shanks","Alésoirs de finition pour cônes Morse et métrique, à queue cylindrique et à queue cône Morse",2009-02-23,2,['25.100.30'],ISO/TC 29/SC 9,9599,[7064],[68940],"['en','fr']",3,<p>ISO 2250:2008 specifies the dimensions of cylindrical shank socket reamers and taper shank socket reamers manufactured to produce self-holding taper sockets for self-holding taper shanks of the following designations:</p><ul><li> metric tapers no. 4 and no. 6;</li><li> Morse tapers no. 0 to no. 6 inclusive.</li></ul><p>The dimensional characteristics of these socket reamers are in accordan

73358,IS,,ISO 22507:2018,Plain bearings — Fluid film bearing materials for vehicular turbocharger,Titre manque,2018-08-29,1,['21.100.10'],ISO/TC 123/SC 7,9599,,[77120],['en'],7,<p>This document specifies the material compositions and required properties of fluid film bearings used for vehicular turbochargers.</p>

7065,IS,,ISO 2251:1975,Lined antistatic rubber footwear,"Articles chaussants doublés, en caoutchouc anti-électrostatique",1975-07-01,1,['13.340.50'],ISO/TC 94/SC 3,9599,,[7066],"['en','fr']",6,

40997,IS,,ISO 22514-1:2009,Statistical methods in process management — Capability and performance — Part 1: General principles and concepts,Méthodes statistiques dans la gestion de processus — Aptitude et performance — Partie 1: Principes et concepts généraux,2009-09-29,1,['03.120.30'],ISO/TC 69/SC 4,9599,,[64135],"['en','fr']",24,<p>ISO 22514-1:2009 describes the fundamental principles of capability and performance of manufacturing processes. It has been prepared to provide guidance about circumstances where a capability study is requested or is necessary to determine if the output from a manufacturing process or the production equipment (a production machine) is acceptable according to app

46530,IS,,ISO 22514-2:2013,Statistical methods in process management — Capability and performance — Part 2: Process capability and performance of time-dependent process models,Méthodes statistiques dans la gestion de processus — Aptitude et performance — Partie 2: Aptitude de processus et performance des modèles de processus dépendants du temps,2013-08-30,1,['03.120.30'],ISO/TC 69/SC 4,9599,[34685],[71617],['en'],22,<p>ISO 22514-2:2013 describes a procedure for the determination of statistics for estimating the quality capability or performance of product and process characteristics. The process results of these quality characteristics are categorized into eight possible distribution types.

71617,IS,,ISO 22514-2:2017,Statistical methods in process management — Capability and performance — Part 2: Process capability and performance of time-dependent process models,Méthodes statistiques dans la gestion de processus — Aptitude et performance — Partie 2: Aptitude de processus et performance des modèles de processus dépendants du temps,2017-02-06,2,['03.120.30'],ISO/TC 69/SC 4,9599,[46530],[88883],['en'],21,"<p>ISO 22514-2:2017 describes a procedure for the determination of statistics for estimating the quality capability or performance of product and process characteristics. The process results of these quality characteristics are categorized into eight possible distribution types.

46531,IS,,ISO 22514-3:2008,Statistical methods in process management — Capability and performance — Part 3: Machine performance studies for measured data on discrete parts,Méthodes statistiques dans la gestion de processus — Aptitude et performance — Partie 3: Études de performance de machines pour des données mesurées sur des parties discrètes,2008-02-07,1,['03.120.30'],ISO/TC 69/SC 4,9599,[42005],[69642],['en'],23,"<p>ISO 22514-3:2008 prescribes the steps to be taken in conducting short-term performance studies that are typically performed on machines where parts produced consecutively under repeatability conditions are considered. The number of observations to be analysed will vary accord

54077,IS,,ISO 22514-7:2012,Statistical methods in process management — Capability and performance — Part 7: Capability of measurement processes,Méthodes statistiques dans la gestion de processus — Aptitude et performance — Partie 7: Aptitude des processus de mesure,2012-09-12,1,['03.120.30'],ISO/TC 69/SC 4,9599,,[80624],"['en','fr']",46,<p>ISO 22514-7:2012 defines a procedure to validate measuring systems and a measurement process in order to state whether a given measurement process can satisfy the requirements for a specific measurement task with a recommendation of acceptance criteria. The acceptance criteria are defined as a capability figure or a capability ratio.</p>

73381,IS,,ISO 22519:2019,Purified water and water for injection pretreatment and production systems,Systèmes de prétraitement et de production d'eau purifiée et d'eau d'injection,2019-05-29,1,['13.060.01'],ISO/TC 282,9599,,[80391],['en'],35,"<p>This document specifies design, materials selection, construction and operation of Purified Water (PW) and Water for Injection (WFI) pretreatment and membrane-based production systems.</p><p>As many different types of feed water are possible, different components and configurations are presented. A decision matrix is provided to give guidance for the different types of feed water.</p><p>This document excludes</p><p>— selection of the appropri

7068,IS,,ISO 2253:1974,Spices and condiments — Curry powder — Specification,Épices — Poudre de carry — Spécifications,1974-02-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[7069],"['en','fr']",2,

7069,IS,,ISO 2253:1986,Curry powder — Specification,Poudre de carry — Spécifications,1986-03-06,2,['67.220.10'],ISO/TC 34/SC 7,9599,[7068],[22117],"['en','fr']",3,

7070,IS,,ISO 2254:1980,"Cloves, whole and ground (powdered) — Specification",Clous de girofle entiers et clous de girofle en poudre — Spécifications,1980-06-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[36678],"['en','fr']",4,"<p>Gives the definition, classification and designation of shaped insulating refratory materials. According to the definition they have a total porosity of at least 45%. One distinguishes between high alumina products, fireclay and siliceous fireclay products, semi-silica products, silica products, basic products and special products. High alumina, fireclay and siliceous fireclay products are subdivided depending on the temperature at which the material does not show any pe

7071,IS,,ISO 2255:1980,"Coriander, whole or ground (Powdered) — Specification",Coriandre entière et coriandre en poudre — Spécifications,1980-09-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[7072],"['en','fr']",4,

73419,IS,,ISO 22550:2019,Document management — AFP interchange for PDF,Gestion des documents — Conversion de fichiers AFP en PDF,2019-07-31,1,"['35.240.30','37.100.99']",ISO/TC 171/SC 2,9599,,[83085],['en'],34,"<p>This document specifies Advanced Function Presentation (AFP) interchange as a container for document objects by defining the AFP file format [Mixed Object Document Content Architecture (MO:DCA)[1]]. It includes a means of identifying support for specifically including single and multi-page Portable Document Format (PDF) document objects as a container function set. It also includes a mechanism for pairing and managing resources associated with PDF.</p><p>NOTE For an example o

41015,IS,,ISO 22554:2007,Ships and marine technology — Propeller shaft revolution indicators — Electric type and electronic type,Navires et technologie maritime — Indicateurs de vitesse d'arbre du propulseur — Type électrique et type électronique,2007-09-13,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[66060],"['en','ru']",9,"<p>ISO 22554:2007 specifies the construction, performance requirements, methods of testing and required test results for electric and electronic propeller shaft revolution indicators required by clause 2.5.4, Regulation 19, chapter V, SOLAS 1974 (as amended, 2000).</p>"

66060,IS,,ISO 22554:2015,Ships and marine technology — Propeller shaft revolution indicators — Electric type and electronic type,Navires et technologie maritime — Indicateurs de vitesse d'arbre du propulseur — Type électrique et type électronique,2015-03-17,2,['47.020.70'],ISO/TC 8/SC 6,9599,[41015],[82081],['en'],9,"<p>ISO 22554:2015 specifies the construction, performance requirements, methods of testing, and required test results for electric and electronic propeller shaft revolution indicators (hereinafter referred to as 'indicator system') required by Clause 2.5.4, Regulation 19, chapter V, SOLAS 1974 (as amended, 2000).</p><p>This International Standard is associated with IMO Resolutio

41016,IS,,ISO 22555:2007,Ships and marine technology — Propeller pitch indicators,Navires et technologie maritime — Indicateurs de pas du propulseur,2007-09-13,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[74756],"['en','ru']",5,"<p>ISO 22555:2007 specifies the construction, performance requirements, methods of testing and required test results for the propeller pitch indicators required by clause 2.5.4, Regulation 19, chapter V, SOLAS 1974 (as amended, 2000).</p>"

61455,IS,,ISO 22559-1:2014,Safety requirements for lifts (elevators) — Part 1: Global essential safety requirements (GESRs),Exigences de sécurité des ascenseurs — Partie 1: Exigences essentielles de sécurité mondiales des ascenseurs (GESR),2014-02-07,1,['91.140.90'],ISO/TC 178,9599,[36318],[73072],"['en','fr']",99,"<p>ISO 22559-1:2014</p><ul><li>specifies GESRs for lifts (elevators), their components and functions, and</li><li>establishes a system and provides methods for minimizing safety risks that may arise in the course of, the operation and use of, or work on, lifts (elevators).</li></ul><p>ISO 22559-1:2014 is applicable to lifts that are intended to carry persons or persons and goods t

71631,IS,,ISO 22568-4:2019,Foot and leg protectors — Requirements and test methods for footwear components — Part 4: Non-metallic perforation resistant inserts,Protecteurs du pied et de la jambe — Exigences et méthodes d'essais pour les composants de chaussure — Partie 4: Inserts anti-perforation non métalliques,2019-03-22,1,['13.340.50'],ISO/TC 94/SC 3,9599,,[82168],"['en','fr']",19,"<p>This document specifies requirements and test methods for the non-metallic inserts with resistance against mechanical perforation, intended to function as components of PPE footwear (e.g. as described by ISO 20345, ISO 20346 and ISO 20347).</p>"

85820,IS,,ISO 22578-2:2024,Graphical symbols — Safety colours and safety signs — Part 2: Measurement of photopic luminance of phosphorescent components used in a natural disaster safety way guidance system,Symboles graphiques — Couleurs de sécurité et signaux de sécurité — Partie 2: Titre manque,2024-02-27,1,['01.080.10'],ISO/TC 145/SC 2,9599,,[89867],['en'],6,<p class='MsoBodyText'><span lang='EN-GB'>This document specifies the laboratory test method for the measurement of photopic luminance of phosphorescent materials classified in accordance with ISO 22578.</span></p>

73488,IS,,ISO 22578:2022,Graphical symbols — Safety colours and safety signs — Natural disaster safety way guidance system,Symboles graphiques — Couleurs de sécurité et signaux de sécurité — Système de guidage pour mise en sécurité en cas de catastrophe naturelle,2022-02-23,1,['01.080.10'],ISO/TC 145/SC 2,9599,,[89867],['en'],32,"<p>This document specifies the principles governing the design and application of signs and plans used to create a natural disaster safety way guidance system to help people evacuate to safe areas or places of refuge in case of natural disasters (e.g. tsunamis, floods, debris flows, steep slope failures, landslides, tornados, large-scale fires, active volcanoes).</p

4100,IS,,ISO 226:1987,Acoustics — Normal equal-loudness level contours,Acoustique — Lignes isosoniques normales,1987-05-07,1,['13.140'],ISO/TC 43,9599,[4099],"[34222,30173]","['en','fr']",8,<p>Specifies the relations existing between the sound pressure levels and frequencies of pure sinusoidal continuous tones in several conditions. These relations are expressed as curves and represent a fundamental property of the human auditory system.</p>

34222,IS,,ISO 226:2003,Acoustics — Normal equal-loudness-level contours,Acoustique — Lignes isosoniques normales,2003-08-21,2,['13.140'],ISO/TC 43,9599,[4100],"[81331,83117,56052]","['en','fr']",18,"<p>This International Standard specifies combinations of sound pressure levels and frequencies of pure continuous tones which are perceived as equally loud by human listeners. The specifications are based on the following conditions: the sound field in the absence of the listener consists of a free progressive plane wave; the source of sound is directly in front of the listener; the sound signals are pure tones; the sound pressure level is measured at the position where the centre of the listener

35054,IS,,ISO 22608:2004,"Protective clothing — Protection against liquid chemicals — Measurement of repellency, retention, and penetration of liquid pesticide formulations through protective clothing materials","Vêtements de protection — Protection contre les produits chimiques liquides — Mesurage de la répulsion, de la rétention et de la pénétration des formulations de pesticides liquides à travers les matériaux des vêtements de protection",2004-07-02,1,['13.340.10'],ISO/TC 94/SC 13,9599,,[79864],"['en','fr']",11,"<p>ISO 22608:2004 specifies a test method to measure repellency, retention and penetration of a known volume of liquid pesticide when applied to protective clothing material. No

7077,IS,,ISO 2261:1972,Reciprocating internal combustion engines — Hand operated control devices — Standard direction of motion,Moteurs alternatifs à combustion interne — Dispositifs de commande manuels — Sens de manoeuvre normaux,1972-05-01,1,['27.020'],ISO/TC 70,9599,,[23830],"['en','fr']",4,

35056,IS,,ISO 22610:2006,"Surgical drapes, gowns and clean air suits, used as medical devices, for patients, clinical staff and equipment — Test method to determine the resistance to wet bacterial penetration","Champs chirurgicaux, casaques et tenues de bloc, utilisés en tant que dispositifs médicaux, pour les patients, le personnel et les équipements — Méthode d'essai de résistance à la pénétration de la barrière bactérienne à l'état humide",2006-06-21,1,['13.340.10'],ISO/TC 94/SC 13,9599,,"[52121,63671]","['en','fr','ru']",14,"<p>ISO 22610:2006 specifies a test method, with associated test apparatus, which is used to determine the resistance of a material to the penetration of bacteria, ca

7078,IS,,ISO 2262:1972,Rope thimbles,Cosses de câbles,1972-03-01,1,['53.020.30'],ISO/TC 111,9599,,[7079],"['en','fr']",4,

40707,IS,,ISO 22621-1:2007,Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) — Polyamide (PA) — Part 1: General,Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux pour des pressions maximales de service inférieures ou égales à 2 MPa (20 bar) — Polyamide (PA) — Partie 1: Généralités,2007-11-01,1,"['75.200','83.140.30']",ISO/TC 138/SC 4,9599,,"[56837,59176]","['en','ru']",29,"<p>ISO 22621-1:2007 specifies the general properties of polyamide (PA) compounds for the manufacture of pipes, fittings and valves made from these compounds, intended to be buried and used for the supply of g

40708,IS,,ISO 22621-2:2007,Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) — Polyamide (PA) — Part 2: Pipes,Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux pour des pressions maximales de service inférieures ou égales à 2 MPa (20 bar) — Polyamide (PA) — Partie 2: Tubes,2007-11-01,1,"['75.200','83.140.30']",ISO/TC 138/SC 4,9599,,"[56838,59177]","['en','ru']",11,"<p>ISO 22621-2:2007 specifies the physical and mechanical properties of pipes made from polyamide (PA) in accordance with ISO 22621-1, intended to be buried and used for the supply of gaseous fuels at maximum operati

40709,IS,,ISO 22621-3:2007,Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) — Polyamide (PA) — Part 3: Fittings,Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux pour des pressions maximales de service inférieures ou égales à 2 MPa (20 bar) — Polyamide (PA) — Partie 3: Raccords,2007-11-01,1,"['75.200','83.140.30']",ISO/TC 138/SC 4,9599,,"[59178,56839]","['en','ru']",22,"<p>ISO 22621 specifies the physical and mechanical properties of fittings made from polyamide (PA) in accordance with ISO 22621-1, intended to be buried and used for the supply of gaseous fuels at maximum opera

50097,IS,,ISO 22621-5:2010,Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) — Polyamide (PA) — Part 5: Fitness for purpose of the system,Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux pour des pressions maximales de service inférieures ou égales à 2 MPa (20 bar) — Polyamide (PA) — Partie 5: Aptitude à l'emploi du système,2010-04-08,1,"['75.200','83.140.30']",ISO/TC 138/SC 4,9599,,"[59179,56840]",['en'],22,"<p>ISO 22621-5:2010 specifies the requirements of fitness for purpose of the polyamide (PA) piping system, intended to be buried and used for the supply of gaseous fuels

50938,IS,,ISO 22621-6:2010,"Plastics piping systems for the supply of gaseous fuels for maximum operating pressures up to and including 2 MPa (20 bar) — Polyamide (PA) — Part 6: Code of practice for design, handling and installation","Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux pour des pressions maximales de service inférieures ou égales à 2 MPa (20 bar) — Polyamide (PA) — Partie 6: Code de pratique pour la conception, la manutention et l'installation",2010-04-08,1,"['75.200','83.140.30']",ISO/TC 138/SC 4,9599,,"[56841,59180]",['en'],21,"<p>ISO 22621-6:2010 specifies a code of practice dealing with polyamide (PA) piping systems, intended to b

73487,IS,,ISO 22634-1:2017,Cigarettes — Determination of benzo[a]pyrene in cigarette mainstream smoke using GC/MS — Part 1: Method using methanol as extraction solvent,Cigarettes — Dosage du benzo[a]pyrène dans le courant principal de la fumée de cigarette par CG/SM — Partie 1: Méthode utilisant du méthanol comme solvant d'extraction,2017-12-01,1,['65.160'],ISO/TC 126,9599,[41040],[76379],"['en','fr']",11,<p>ISO 22634-1:2017 specifies a method for the determination of benzo[a]pyrene (B[a]P) in the total particulate matter of cigarette mainstream smoke using gas chromatography/mass spectrometry (GC/MS) with methanol as extraction solvent.</p><p>This method was validated using ISO 3308 smoking

63663,IS,,ISO 22634-2:2017,Cigarettes — Determination of benzo[a]pyrene in cigarette mainstream smoke using GC/MS — Part 2: Method using cyclohexane as extraction solvent,Cigarettes — Dosage du benzo[a]pyrène dans le courant principal de la fumée de cigarette par CG/SM — Partie 2: Méthode utilisant du cyclohexane comme solvant d'extraction,2017-12-01,1,['65.160'],ISO/TC 126,9599,,[76380],"['en','fr']",10,"<p>ISO 22634-2:2017 specifies a method for the determination of benzo[a]pyrene (B[a]P) in the total particulate matter of cigarette mainstream smoke using gas chromatography/mass spectrometry (GC/MS) with cyclohexane as extraction solvent.</p><p>This method was validated using ISO 3308 smok

41040,IS,,ISO 22634:2008,Cigarettes — Determination of benzo[a]pyrene in cigarette mainstream smoke — Method using gas chromatography/mass spectrometry,Cigarettes — Dosage du benzo[a]pyrène dans le courant principal de la fumée de cigarettes — Méthode par couplage de chromatographie en phase gazeuse/spectrométrie de masse,2008-11-11,1,['65.160'],ISO/TC 126,9599,,[73487],"['en','fr']",10,"ISO 22634:2008 specifies a method for the determination of benzo[a]pyrene (B[a]P) in the total particulate matter of cigarette mainstream smoke. <p>This method is specified using ISO 3308 smoking parameters, but is technically compatible with other smoking regimes.</p>"

7081,IS,,ISO 2264:1972,Rolling bearings — Bearings with spherical outside surface and extended inner ring width,Roulements — Roulements à surface extérieure sphérique et à bague intérieure large,1972-08-01,3,['21.100.20'],ISO/TC 4,9599,[7080],[17442],"['en','fr']",6,

36375,IS,,ISO 22641:2005,Space data and information transfer systems — TM (telemetry) synchronization and channel coding,Systèmes de transfert des données et informations spatiales — Synchronisation TM (télémesure) et codage de canal,2005-07-22,1,['49.140'],ISO/TC 20/SC 13,9599,,[60590],['en'],80,<p>ISO 22641:2005 specifies synchronization and channel coding schemes used in conjunction with the telemetry (TM) space data link protocol as defined by ISO 22645 or the advanced orbiting systems (AOS) space data link protocol defined by ISO 22666. These schemes are to be used over space-to-ground or space-to-space communications links by space missions.</p>

36376,IS,,ISO 22642:2005,Space data and information transfer systems — TC (telecommand) synchronization and channel coding,Systèmes de transfert des données et informations spatiales — Synchronisation TC (télécommande) et codage de canal,2005-07-20,1,['49.140'],ISO/TC 20/SC 13,9599,,[62446],['en'],50,<p>ISO 22642:2005 defines synchronization and channel coding schemes used with the telecommand (TC) space data link protocol as defined in ISO 22664. These schemes are to be used over ground-to-space or space-to-space communications links by space missions.</p>

50342,IS,Cor,ISO 22642:2005/Cor 1:2007,Space data and information transfer systems — TC (telecommand) synchronization and channel coding — Technical Corrigendum 1,Systèmes de transfert des données et informations spatiales — Synchronisation TC (télécommande) et codage de canal — Rectificatif technique 1,2007-10-03,1,['49.140'],ISO/TC 20/SC 13,9599,,[62446],['en'],4,

42722,IS,,ISO 22644:2006,Space data and information transfer systems — Orbit data messages,Systèmes de transfert des informations et données spatiales — Messages pour données d'orbites,2006-04-26,1,['49.140'],ISO/TC 20/SC 13,9599,,[46135],['en'],50,"<p>ISO 22644:2006 specifies two standard message formats for use in transferring spacecraft orbit information between space Agencies: the Orbit Parameter Message (OPM) and the Orbit Ephemeris Message (OEM). Such exchanges are used for</p><ul><li>pre-flight planning for tracking or navigation support;</li><li>scheduling tracking support;</li><li>carrying out tracking operations (sometimes called metric predicts);</li><li>performing orbit compariso

36380,IS,,ISO 22645:2005,Space data and information transfer systems — TM (telemetry) space data link protocol,Systèmes de transfert des données et informations spatiales — Protocole pour liaison de données spatiales TM (télémesure),2005-07-22,1,['49.140'],ISO/TC 20/SC 13,9599,,[70698],['en'],96,"<p>ISO 22645:2005 specifies the telemetry (TM) space data link protocol, a data link layer protocol as defined in ISO/IEC 7498-1, and is be used over space-to-ground or space-to-space communications links by space missions. </p>"

68741,IS,Amd,ISO 22645:2005/Amd 1:2015,Space data and information transfer systems — TM (telemetry) space data link protocol — Amendment 1,Systèmes de transfert des données et informations spatiales — Protocole pour liaison de données spatiales TM (télémesure) — Amendement 1,2015-07-09,1,['49.140'],ISO/TC 20/SC 13,9599,,[70698],['en'],1,

36383,IS,,ISO 22647:2006,Space data and information transfer systems — Space link identifiers,Systèmes de transfert des informations et données spatiales — Identificateurs de liaisons spatiales,2006-02-17,1,['49.140'],ISO/TC 20/SC 13,9599,,[45987],['en'],35,<p>ISO 22647:2006 specifies the identifiers currently used by the space link protocols and shows how these identifiers are managed at the level of the Consultative Committee for Space Data Systems (CCSDS). It does not specify how these identifiers are managed in individual data systems of space projects.</p>

35067,IS,,ISO 22649:2003,Footwear — Test methods for insoles and insocks — Water absorption and desorption,Chaussures — Méthodes d'essai applicables aux premières de montage et aux premières de propreté — Absorption et désorption d'eau,2003-11-19,1,['61.060'],ISO/TC 216,9599,,[60982],['en'],9,"<p>ISO 22649:2003 specifies two test methods for determining the water absorption and desorption of insoles and insocks, irrespective of the material. These methods are:</p><ul><li> Method A: Determination of the static water absorption and desorption of insoles and insocks.</li><li> Method B: Determination of the dynamic water absorption and desorption of insoles.</li></ul>"

35068,IS,,ISO 22650:2002,Footwear — Test methods for whole shoe — Heel attachment,Chaussures — Méthodes d'essai applicables à la chaussure entière — Fixation du talon,2002-10-03,1,['61.060'],ISO/TC 216,9599,,[63247],"['en','fr']",9,<p>ISO 22650 specifies a method for the determination of the heel attachment of footwear and applies to women's medium- and high-heeled footwear.</p><p>This test method measures three related wear properties:</p><ul><li>the rigidity of the shoe backpart during normal walking;</li><li>the amount of permanent deformation of the backpart caused by a fairly large force applied to the heel in a backward direction;</li><li>the force required to detach the heel.</li></ul

7084,IS,,ISO 2266:1974,Textile machinery and accessories — Metal travellers for spinning and twisting,Matériel pour l'industrie textile — Curseurs métalliques pour anneaux de continus à filer et à retordre,1974-03-01,1,['59.120.10'],ISO/TC 72/SC 1,9599,[7083],"[3762,3763]","['en','fr']",3,

36384,IS,,ISO 22662:2007,Milk and milk products — Determination of lactose content by high-performance liquid chromatography (Reference method),Lait et produits laitiers — Détermination de la teneur en lactose par chromatographie liquide haute performance (Méthode de référence),2007-09-13,1,['67.100.01'],ISO/TC 34/SC 5,9599,,[84827],"['en','fr','ru']",10,"<p>ISO 22662|IDF 198:2007 specifies the reference method for the determination of lactose content of raw milk, heat-treated milks, dried milk and raw and pasteurized cream.</p><p>The method is not applicable to fermented milks and milks to which oligosaccharides have been added.</p>"

36386,IS,,ISO 22663:2006,Space data and information transfer systems — Proximity-1 space link protocol — Data link layer,Systèmes de transfert des informations et données spatiales — Protocole pour liaisons spatiales de proximité 1 — Couche de liaisons de données,2006-04-19,1,['49.140'],ISO/TC 20/SC 13,9599,,[45000],['en'],132,"<p>ISO 22663:2006 defines the data link layer (framing, media access, data services and input-output sublayers) of a Proximity-1 space link protocol. The specifications for the protocol data units, framing, media access control, expedited and sequenced controlled data transfer, timing service, i/o control as well as the procedures for establishing and terminating a se

45000,IS,,ISO 22663:2007,Space data and information transfer systems — Proximity-1 space link protocol — Data link layer,Systèmes de transfert des informations et données spatiales — Protocole pour liaisons spatiales de proximité 1 — Couche de liaisons de données,2007-10-10,2,['49.140'],ISO/TC 20/SC 13,9599,[36386],[67091],['en'],139,"<p>ISO 22663:2007 defines the Proximity-1 space link protocol data link layer (framing, media access, data services, and input-output sublayers). It specifies the protocol data units, framing, media access control, expedited and sequenced controlled data transfer, timing service, i/o control, as well as the procedures for establishing and terminating a session

36389,IS,,ISO 22664:2005,Space data and information transfer systems — TC (telecommand) space data link protocol,Systèmes de transfert des données et informations spatiales — Protocole de liaison pour données spatiales TC (télécommande),2005-08-18,1,['49.140'],ISO/TC 20/SC 13,9599,,[61746],['en'],110,"<p>ISO 22664:2005 specifies the telecommand (TC) space data link protocol, a data link layer protocol as defined in ISO/IEC 7498-1, that is to be used over ground-to-space or space-to-space communications links by space missions. </p>"

61746,IS,,ISO 22664:2013,Space data and information transfer systems — TC (telecommand) space data link protocol,Systèmes de transfert des données et informations spatiales — Protocole de liaison pour données spatiales TC (télécommande),2013-05-29,2,['49.140'],ISO/TC 20/SC 13,9599,[36389],[70699],['en'],106,"<p>ISO 22664:2013 specifies the telecommand (TC) space data link protocol. This protocol is a data link layer protocol (as defined in ISO/IEC 7498-1) intended for use over ground-to-space or space-to-space communications links by space missions. </p><p>ISO 22664:2013 defines the TC space data link protocol in terms of</p><ol><li>the services provided to the users of this protocol,</li><l

68744,IS,Amd,ISO 22664:2013/Amd 1:2015,Space data and information transfer systems — TC (telecommand) space data link protocol — Amendment 1,Systèmes de transfert des données et informations spatiales — Protocole de liaison pour données spatiales TC (télécommande) — Amendement 1,2015-07-09,2,['49.140'],ISO/TC 20/SC 13,9599,,[70699],['en'],1,

36391,IS,,ISO 22666:2005,Space data and information transfer systems — AOS (advanced orbiting systems) space data link protocol,Systèmes de transfert des données et informations spatiales — Protocole de liaison pour données spatiales AOS (systèmes perfectionnés sur orbite),2005-08-18,1,['49.140'],ISO/TC 20/SC 13,9599,,[44866],['en'],97,"<p>ISO 22666:2005 specifies the advanced orbiting systems (AOS) space data link protocol, a data link layer protocol as defined in ISO/IEC 7498-1, that is to be used over space-to-ground, ground-to-space, or space-to-space communications links by space missions. </p>"

44866,IS,,ISO 22666:2007,Space data and information transfer systems — AOS (advanced orbiting systems) space data link protocol,Systèmes de transfert des données et informations spatiales — Protocole de liaison pour données spatiales AOS (systèmes perfectionnés sur orbite),2007-08-15,2,['49.140'],ISO/TC 20/SC 13,9599,[36391],"[60519,70701]",['en'],95,"<p>ISO 22666:2007 specifies the advanced orbiting systems (AOS) space data link protocol, a data link layer protocol as defined in ISO/IEC 7498-1, that is to be used over space-to-ground, ground-to-space, or space-to-space communications links by space missions. </p>"

68747,IS,Amd,ISO 22666:2007/Amd 1:2015,Space data and information transfer systems — AOS (advanced orbiting systems) space data link protocol — Amendment 1,Systèmes de transfert des données et informations spatiales — Protocole de liaison pour données spatiales AOS (systèmes perfectionnés sur orbite) — Amendement 1,2015-06-16,2,['49.140'],ISO/TC 20/SC 13,9599,,[70701],['en'],1,

36392,IS,,ISO 22667:2005,Space data and information transfer systems — Communication operations Procedure-1,Systèmes de transfert des données et informations spatiales — Procédure 1 pour les opérations de communication,2005-08-19,1,['49.140'],ISO/TC 20/SC 13,9599,,[61747],['en'],88,"<p>ISO 22667:2005 specifies the communications operation Procedure-1 (COP-1). This procedure is used in conjunction with the telecommand (TC) space data link protocol, as defined by ISO 22664, to enable the delivery of service data units to the receiving end of the layer above, correct and without omission or duplication, and in the same sequential order in which they were received from the layer above at the se

36394,IS,,ISO 22669:2003,Space data and information transfer systems — Space link extension (SLE) — Return-all-frames service,Systèmes de transfert des informations et données spatiales — Extension de liaisons spatiales (SLE) — Service de retour par tout réseau,2003-12-12,1,['49.140'],ISO/TC 20/SC 13,9599,,[43442],['en'],135,"<p>ISO 22669:2003 specifies a return-all-frames (RAF) service for a space link extension (SLE) service. The RAF service is an SLE transfer service that delivers all telemetry frames to a mission user from one space link physical channel.</p><p>ISO 22669:2003 defines, in an abstract manner, the RAF service in terms of the operations necessary to provide the service; the

43442,IS,,ISO 22669:2007,Space data and information transfer systems — Space link extension (SLE) — Return-all-frames service,Systèmes de transfert des données et informations spatiales — Extension de liaisons spatiales (SLE) — Service de retour par tout réseau,2007-01-26,2,['49.140'],ISO/TC 20/SC 13,9599,[36394],[61743],['en'],143,"<p>ISO 22669:2007 defines the space link extension (SLE) return-all-frames (RAF) service in conformance with ISO 15396:1998. The RAF service is an SLE transfer service that delivers to a mission user all telemetry frames from one space link physical channel.</p><p>ISO 22669:2007 defines, in an abstract manner, the RAF service in terms of</p><ul><li>the operations

61743,IS,,ISO 22669:2013,Space data and information transfer systems — Space link extension (SLE) — Return-all-frames service,Systèmes de transfert des données et informations spatiales — Extension de liaisons spatiales (SLE) — Service de retour par tout réseau,2013-05-29,3,['49.140'],ISO/TC 20/SC 13,9599,[43442],[74554],['en'],140,"<p>ISO 22669:2013 defines the space link extension (SLE) return-all-frames (RAF) service in conformance with the SLE reference model (ISO 15396:2007). The RAF service is an SLE transfer service that delivers to a mission user all telemetry frames from one space link physical channel.</p><p>ISO 22669:2013 defines the RAF service in terms of</p><ol><li>the operatio

7085,IS,,ISO 2267:1979,Surface active agents — Evaluation of certain effects of laundering — Methods of preparation and use of unsoiled cotton control cloth,Agents de surface — Contrôle de certains effets de blanchissage — Méthode d'élaboration et de mise en oeuvre d'un tissu de coton témoin non souillé,1979-02-01,2,['71.100.40'],ISO/TC 91,9599,,[7086],"['en','fr']",6,

36395,IS,,ISO 22670:2006,Space data and information transfer systems — Space link extension (SLE) — Return-channel-frames service,Systèmes de transfert des informations et données spatiales — Extension de liaisons spatiales (SLE) — Service de réseau pour liaison retour,2006-03-31,1,['49.140'],ISO/TC 20/SC 13,9599,,[61744],['en'],145,"<p>ISO 22670:2006 specifies a return-channel-frames (RCF) service for a space link extension (SLE). The RCF service is an SLE transfer service that delivers to a mission user all telemetry frames from one master channel or one virtual channel.</p><p>It defines, in an abstract manner, the RCF service in terms of</p><ul><li>the operations necessary to provide the

61744,IS,,ISO 22670:2013,Space data and information transfer systems — Space link extension (SLE) — Return-channel-frames service,Systèmes de transfert des informations et données spatiales — Extension de liaisons spatiales (SLE) — Service de réseau pour liaison retour,2013-05-29,2,['49.140'],ISO/TC 20/SC 13,9599,[36395],[74555],['en'],144,"<p>ISO 22670:2013 defines the space link extension (SLE) return-channel-frames (RCF) service in accordance with the SLE Reference Model (ISO 15396:2007). The RCF service is an SLE transfer service that delivers to a mission user all telemetry frames from one master channel or one virtual channel.</p><p>ISO 22670:2013 defines the RCF service in terms of</p

36396,IS,,ISO 22671:2005,Space data and information transfer systems — Space link extension (SLE) — Forward command link transmission unit (CLTU),Systèmes de transfert des données et informations spatiales — Extension de liaisons spatiales (SLE) — Unité de transmission pour la liaison d'envoi de télécommande (CLTU),2005-06-15,1,['49.140'],ISO/TC 20/SC 13,9599,,[43443],['en'],141,<p>ISO 22671:2005 specifies the forward command link transmission unit (CLTU) that may be provided by a space link extension (SLE) system for inter-agency cross support. The CLTU service is an SLE transfer service that enables a mission to send CLTUs to a spacecraft.</p>

43443,IS,,ISO 22671:2007,Space data and information transfer systems — Space link extension (SLE) — Forward communications link transmission unit (CLTU) service,Systèmes de transfert des données et informations spatiales — Extension de liaisons spatiales (SLE) — Service de l'unité de transmission pour la liaison d'envoi de télécommande (CLTU),2007-01-26,2,['49.140'],ISO/TC 20/SC 13,9599,[36396],[58052],['en'],149,"<p>ISO 22671:2007 defines the communications link transmission unit (CLTU) service in conformance with the transfer services specified in ISO 15396:1998. The forward CLTU service is a space link extension (SLE) transfer service that enables a mission to send communications link tra

58052,IS,,ISO 22671:2011,Space data and information transfer systems — Space link extension (SLE) — Forward communications link transmission unit (CLTU) service,Systèmes de transfert des informations et données spatiales — Extension de liaisons spatiales (SLE) — Service de l'unité de transmission pour la liaison d'envoi de télécommande (CLTU),2011-11-08,3,['49.140'],ISO/TC 20/SC 13,9599,[43443],[74557],['en'],159,"<p>ISO 22671:2011 defines the Communications Link Transmission Unit (CLTU) service in conformance with the transfer services specified in CCSDS 910.4-B-2 (equivalent to ISO 15396). The Forward CLTU service is a Space Link Extension (SLE) transfer service that enables a mission to s

42721,IS,,ISO 22672:2006,Space data and information transfer systems — Space link extension (SLE) — Forward space packet service,Systèmes de transfert des informations et données spatiales — Extension de liaisons spatiales (SLE) — Envoi de données spatiales par paquets,2006-05-10,1,['49.140'],ISO/TC 20/SC 13,9599,,[58053],['en'],194,"<p>The Forward Space Packet (FSP) service is a Space Link Extension (SLE) transfer service that enables a mission to send Space Packets to a spacecraft in sequence-controlled or expedited mode. ISO 22672:2006 defines, in an abstract manner, the FSP service in terms of</p><ul><li>the operations necessary to provide the transfer service;</li><li>the parameter data

58053,IS,,ISO 22672:2011,Space data and information transfer systems — Space link extension (SLE) — Forward space packet service specification,Systèmes de transfert des informations et données spatiales — Extension de liaisons spatiales (SLE) — Spécification d'envoi de données spatiales par paquets,2011-11-08,2,['49.140'],ISO/TC 20/SC 13,9599,[42721],[74558],['en'],209,"<p>ISO 22672:2011 defines the Forward Space Packet (FSP) service in conformance with the transfer services specified in CCSDS 910.4-B-2 (equivalent to ISO 15396). The FSP service is a Space Link Extension (SLE) transfer service that enables a mission to send Space Packets to a spacecraft in sequence-controlled or expedited mo

36412,IS,,ISO 22674:2006,Dentistry — Metallic materials for fixed and removable restorations and appliances,Art dentaire — Matériaux métalliques pour les restaurations fixes et amovibles et les appareillages,2006-11-21,1,['11.060.10'],ISO/TC 106/SC 2,9599,"[13387,24817,40596,40005,30433,30885,33951,22058]",[59620],"['en','fr']",22,"<p>ISO 22674:2006 classifies metallic materials that are suitable for the fabrication of dental appliances and restorations, including metallic materials recommended for use either with or without a ceramic veneer, or recommended for both uses, and specifies their requirements. It further specifies requirements with respect to packaging and marking the products an

59620,IS,,ISO 22674:2016,Dentistry — Metallic materials for fixed and removable restorations and appliances,Médecine bucco-dentaire — Matériaux métalliques pour les restaurations fixes et amovibles et les appareillages,2016-01-15,2,['11.060.10'],ISO/TC 106/SC 2,9599,[36412],[77202],"['en','fr']",36,"<p>ISO 22674:2016 classifies metallic materials that are suitable for the fabrication of dental restorations and appliances, including metallic materials recommended for use either with or without a ceramic veneer, or recommended for both uses, and specifies their requirements. Furthermore, it specifies requirements with respect to packaging and marking the products and to the instructions to be

36413,IS,,ISO 22675:2006,Prosthetics — Testing of ankle-foot devices and foot units — Requirements and test methods,Prothèses — Essais d'articulations cheville-pied et unités de pied — Exigences et méthodes d'essai,2006-09-14,1,['11.040.40'],ISO/TC 168,9599,,[70203],"['en','fr','ru']",92,"<p>ISO 22675:2006 primarily specifies a cyclic test procedure for ankle-foot devices and foot units of external lower limb prostheses, distinguished by the potential to realistically simulate those loading conditions of the complete stance phase of walking from heel strike to toe-off that are relevant to the verification of performance requirements such as strength, durability and service life.</p><p>In add

70203,IS,,ISO 22675:2016,Prosthetics — Testing of ankle-foot devices and foot units — Requirements and test methods,Prothèses — Essais d'articulations cheville-pied et unités de pied — Exigences et méthodes d'essai,2016-05-26,2,['11.040.40'],ISO/TC 168,9599,[36413],[79620],"['en','fr']",91,"<p>IMPORTANT ? ISO 22675:2016 <i>is suitable</i> for the assessment of the conformity of prosthetic ankle-foot devices and foot units with the strength requirements specified in 4.4 of ISO 22523:2006 (see NOTE 1). Prosthetic ankle-foot devices and foot units on the market, which have demonstrated their compliance with the strength requirements specified in 4.4 of ISO 22523:2006 through submission to the r

7089,IS,,ISO 2269:1973,Magnetic compasses and accessories — Rules for testing and certification,Compas magnétiques et leurs accessoires — Règles pour l'essai et la certification,1973-05-01,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[7090],"['en','fr']",39,

7090,IS,,ISO 2269:1992,"Shipbuilding — Class A magnetic compasses, azimuth reading devices and binnacles — Tests and certification","Construction navale — Compas magnétiques, alidades et habitacles de classe A — Essais et certification",1992-04-30,2,['47.020.70'],ISO/TC 8/SC 6,9599,[7089],[43301],"['en','fr']",22,"<p>Specifies type-test and individual test methods, and gives the acceptable limits of the characteristics necessary to guarantee conformity to the general specifications given in ISO 449. Annexes A, B and C include type-test and individual test certificates.</p>"

7091,IS,,ISO 2270:1972,Surface active agents — Ethylene oxide adducts — Iodometric determination of oxyethylene groups,Agents de surface — Dérivés polyéthylènes — Dosage iodométrique des groupes oxyéthylène,1972-09-01,1,['71.100.40'],ISO/TC 91,9599,,[7092],"['en','fr']",5,

35099,IS,,ISO 22702:2003,Utility lighters — General consumer-safety requirements,Briquets utilitaires — Exigences générales pour la sécurité des consommateurs,2003-10-28,1,['97.180'],ISO/TC 61/SC 4,9599,,[64743],"['en','fr']",20,"<p>ISO 22702:2003 gives a consumer-safety specification covering all flame-producing consumer products commonly known as utility lighters (also known as grill lighters, fireplace lighters, lighting rods or gas matches), and similar devices. Matches are specifically excluded from the safety specification; flame-producing products intended for igniting cigars, pipes and cigarettes are also specifically excluded from the safety specification.</p>"

45097,IS,Amd,ISO 22702:2003/Amd 1:2008,Utility lighters — General consumer-safety requirements — Amendment 1: Clarification of requirements and addition of safety symbols,Briquets utilitaires — Exigences générales pour la sécurité des consommateurs — Amendement 1: Clarification des exigences et ajout de symboles de sécurité,2008-09-15,1,['97.180'],ISO/TC 61,9599,,[64743],"['en','fr']",4,

7093,IS,,ISO 2271:1972,Surface active agents — Detergents — Determination of anionic-active matter (Direct two-phase titration procedure),Agents de surface — Détergents — Détermination de la teneur en matière active anionique (Méthode par titrage direct dans deux phases),1972-09-01,1,['71.100.40'],ISO/TC 91,9599,,[7094],"['en','fr']",4,

36438,IS,,ISO 22717:2006,Cosmetics — Microbiology — Detection of Pseudomonas aeruginosa,Cosmétiques — Microbiologie — Recherche de Pseudomonas aeruginosa,2006-02-08,1,['07.100.40'],ISO/TC 217,9599,,[68312],"['en','fr','ru']",13,"<p>ISO 22717:2006 gives general guidelines for the detection and identification of the specified micro-organism <i>Pseudomonas aeruginosa </i>in cosmetic products. Micro-organisms considered as specified in this ISO 22717:2006 might differ from country to country according to national practices or regulations.</p><p>In order to ensure product quality and safety for consumers, it is advisable to perform an appropriate microbiological risk analysis to determine the typ

36439,IS,,ISO 22718:2006,Cosmetics — Microbiology — Detection of Staphylococcus aureus,Cosmétiques — Microbiologie — Détection de Staphylococcus aureus,2006-03-15,1,['07.100.40'],ISO/TC 217,9599,,[68313],"['en','fr','ru']",15,"<p>ISO 22718:2006 gives general guidelines for the detection and identification of the specified micro-organism <i>Staphylococcus aureus </i>in cosmetic products. Micro-organisms considered as specified in this International Standard might differ from country to country according to national practices or regulations.</p><p>In order to ensure product quality and safety for consumers, it is advisable to perform an appropriate microbiological risk analysis to determine th

7095,IS,,ISO 2272:1972,Surface active agents — Analysis of soaps — Determination of low contents of free glycerol spectrophotometric method,Agents de surface — Analyse des savons — Dosage du glycérol libre en faibles teneurs — Méthode spectrophotométrique,1972-09-01,1,['71.100.40'],ISO/TC 91,9599,,[7096],"['en','fr']",2,

41082,IS,,ISO 22721:2007,Conveyor belts — Specification for rubber- or plastics-covered conveyor belts of textile construction for underground mining,"Courroies transporteuses — Spécification pour courroies transporteuses à structure textile recouvertes de caoutchouc ou de plastique, pour utilisation dans les mines souterraines",2007-07-10,1,"['53.040.20','73.100.40']",ISO/TC 41/SC 3,9599,,[84826],"['en','fr']",15,<p>ISO 22721:2007 specifies requirements for rubber- or plastics-covered conveyor belting of textile construction for underground mining on flat or troughed idlers. It is not applicable to light conveyor belts as described in ISO 21183‑1. ISO 22721:2007 does not include requirement

73761,IS,,ISO 22733-1:2021,Road vehicles — Test method to evaluate the performance of autonomous emergency braking systems — Part 1: Car-to-car,Véhicules routiers — Méthode d'essai pour évaluer la performance des systèmes automatiques de freinage d'urgence — Partie 1: Voiture à voiture,2021-07-23,1,['43.040.40'],ISO/TC 22/SC 33,9599,,[84241],['en'],18,"<p>This document specifies a method to evaluate the behaviour of a vehicle equipped with an autonomous emergency braking system (AEBS), or dynamic brake support (DBS) during several accident scenarios. Those accidents occur during a straight-line driving when the vehicle under test (VUT) approaches another vehicle in the same lane. Both vehicl