Withdrawn and superseded ISO standards — page 8 of 246

32423,IS,,ISO 10381-1:2002,Soil quality — Sampling — Part 1: Guidance on the design of sampling programmes,Qualité du sol — Échantillonnage — Partie 1: Lignes directrices pour l'établissement des programmes d'échantillonnage,2002-11-29,1,['13.080.05'],ISO/TC 190/SC 7,9599,,"[65223,62842,62365]","['en','fr']",33,"<p>ISO 10381-1:2002 sets out the general principles to be applied in the design of sampling programmes for the purpose of characterizing and controlling soil quality and identifying sources and effects of contamination of soil and related material, with emphasis on</p><ul><li>procedures required to locate points from which samples may be taken for examination or at which instruments

32424,IS,,ISO 10381-2:2002,Soil quality — Sampling — Part 2: Guidance on sampling techniques,Qualité du sol — Échantillonnage — Partie 2: Lignes directrices pour les techniques d'échantillonnage,2002-10-25,1,['13.080.05'],ISO/TC 190/SC 7,9599,,[62843],"['en','fr']",23,"<p>ISO 10381-2:2002 gives guidance on techniques for taking and storing soil samples so that these can subsequently be examined for the purpose of providing information on soil quality.</p><p>ISO 10381-2:2002 gives information on typical equipment that is applicable in particular sampling situations to enable correct sampling procedures to be carried out and representative samples to be collected. Guidance is given on the sele

32425,IS,,ISO 10381-3:2001,Soil quality — Sampling — Part 3: Guidance on safety,Qualité du sol — Échantillonnage — Partie 3: Lignes directrices relatives à la sécurité,2001-12-20,1,['13.080.05'],ISO/TC 190/SC 7,9599,,[62363],"['en','fr']",21,

32426,IS,,ISO 10381-4:2003,"Soil quality — Sampling — Part 4: Guidance on the procedure for investigation of natural, near-natural and cultivated sites","Qualité du sol — Échantillonnage — Partie 4: Lignes directrices pour les procédures d'investigation des sites naturels, quasi naturels et cultivés",2003-04-30,1,['13.080.05'],ISO/TC 190/SC 7,9599,,"[65225,65223,67787]","['en','fr']",13,"<p>ISO 10381-4:2003 describes the sampling of soils of</p><ul><li>natural and near-natural sites;</li><li>areas used for agriculture (arable and pasture sites);</li><li>areas used for horticulture (including domestic gardens, allotments);</li><li>areas used for special crop-cultivation, arboreal, vineyard, e

32427,IS,,ISO 10381-5:2005,Soil quality — Sampling — Part 5: Guidance on the procedure for the investigation of urban and industrial sites with regard to soil contamination,Qualité du sol — Échantillonnage — Partie 5: Lignes directrices pour la procédure d'investigation des sols pollués en sites urbains et industriels,2005-09-20,1,['13.080.05'],ISO/TC 190/SC 7,9599,,"[65225,65226,65223]","['en','fr']",35,"<p>ISO 10381-5:2005 gives guidance on the procedure for the investigation of urban and industrial sites, where either it is known that soil contamination is present, or the presence of soil contamination is suspected. ISO 10381-5:2005 is applicable where there is a need to establish the co

19248,IS,,ISO 10381-6:1993,"Soil quality — Sampling — Part 6: Guidance on the collection, handling and storage of soil for the assessment of aerobic microbial processes in the laboratory","Qualité du sol — Échantillonnage — Partie 6: Lignes directrices pour la collecte, la manipulation et la conservation de sols destinés à une étude en laboratoire des processus microbiens aérobies",1993-11-11,1,['13.080.05'],ISO/TC 190/SC 7,9599,,[43691],"['en','fr']",4,"<p>Describes the procedure to be observed: selection of sampling locations, description of field site, sampling conditions, sampling methods, sample marking, transportation conditions, soil processing, storage conditions, storage period, pre

43691,IS,,ISO 10381-6:2009,"Soil quality — Sampling — Part 6: Guidance on the collection, handling and storage of soil under aerobic conditions for the assessment of microbiological processes, biomass and diversity in the laboratory","Qualité du sol — Échantillonnage — Partie 6: Lignes directrices pour la collecte, la manipulation et la conservation, dans des conditions aérobies, de sols destinés à l'évaluation en laboratoire des processus, de la biomasse et de la diversité microbiens",2009-03-03,2,['13.080.05'],ISO/TC 190/SC 4,9599,[19248],"[68249,65223,62364,62843]","['en','fr']",6,"<p>ISO 10381-6:2009 provides guidance on the collection, handling and storage of soil for subsequent testing

27756,IS,,ISO 10381-7:2005,Soil quality — Sampling — Part 7: Guidance on sampling of soil gas,Qualité du sol — Échantillonnage — Partie 7: Lignes directrices pour l'échantillonnage des gaz du sol,2005-08-30,1,['13.080.05'],ISO/TC 190/SC 7,9599,,[65224],"['en','fr']",38,"<p>ISO 10381-7:2005 contains guidance on the sampling of soil gas.</p><p>ISO 10381-7:2005 is not applicable to the measurement of gases from the soil entering into the atmosphere, the sampling of atmospheric gases, or passive sampling procedures.</p>"

30941,IS,,ISO 10381-8:2006,Soil quality — Sampling — Part 8: Guidance on sampling of stockpiles,Qualité du sol — Échantillonnage — Partie 8: Lignes directrices pour l'échantillonnage des stocks de réserve,2006-04-06,1,['13.080.05'],ISO/TC 190/SC 7,9599,,[65223],"['en','fr']",106,"<p>ISO 10381-8:2006 defines the methods that should be applied when sampling soil from stockpiles. ISO 10381-8:2006 only includes the sampling of the soil material itself, i.e. the solid phase. </p><p>The underlying reason for sampling the soil can differ widely, as can the subsequent analysis on the obtained samples. ISO 10381-8:2006 gives guidance on the various aspects that, together, describe the sampling activi

32422,IS,,ISO 10382:2002,Soil quality — Determination of organochlorine pesticides and polychlorinated biphenyls — Gas-chromatographic method with electron capture detection,Qualité du sol — Dosage des pesticides organochlorés et des biphényles polychlorés — Méthode par chromatographie en phase gazeuse avec détection par capture d'électrons,2002-10-17,1,['13.080.10'],ISO/TC 190/SC 3,9599,,"[84177,76523]","['en','fr']",22,"<p>ISO 10382:2002 specifies a method for quantitative determination of seven polychlorinated biphenyls and seventeen organochlorine pesticides in soil.</p><p>ISO 10382:2002 is applicable to all types of soil.</p><p>Under the conditions specified in ISO 10382:2002, limits of

18447,IS,,ISO 10383:1992,Codes for exchanges and regulated markets — Market identifier codes (MIC),Codes de bourses et marchés réglementés — Codes d'identification des marchés (MIC),1992-10-21,1,['03.060'],ISO/TC 68,9599,,[33444],"['en','fr']",2,<p>Defines the first component (bank code) of the bank identifier code (BIC) specified in ISO 9362. The code consists of four contiguous characters.</p>

33444,IS,,ISO 10383:2003,Securities and related financial instruments — Codes for exchanges and market identification (MIC),Valeurs mobilières et autres instruments financiers concernés — Codes pour échanges et identification de marché (MIC),2003-05-07,2,['03.060'],ISO/TC 68,9599,[18447],[61067],"['en','fr']",3,<p>ISO 10383:2003 provides a uniform structure for exchange and market identification codes (MICs). It is intended for use in any application and communication for identification of primary and secondary markets:</p><ul><li>where the financial instrument is listed (places of official listing) and</li><li>where the related trade is executed (place of trade).</li></ul>

18448,IS,,ISO 10384:1992,Hot-rolled carbon steel sheet for machinery,Tôles laminées à chaud en acier au carbone pour outillage,1992-02-19,1,['77.140.50'],ISO/TC 17/SC 12,9599,,[28049],"['en','fr']",8,"<p>Specifies requirements. Tabulates: the chemical composition (cast analysis), permissible deviations for product analysis, and tolerances for: thickness, width, length, edge camber, out-of-square and flatness.</p>"

28049,IS,,ISO 10384:2001,Hot-rolled carbon steel sheet as defined by chemical composition,Tôles en acier au carbone laminées à chaud définies par leur composition chimique,2001-12-20,2,['77.140.50'],ISO/TC 17/SC 12,9599,[18448],[45026],"['en','fr']",12,

45026,IS,,ISO 10384:2008,Hot-rolled carbon steel sheet as defined by chemical composition,Tôles en acier au carbone laminées à chaud définies par leur composition chimique,2008-08-11,3,['77.140.50'],ISO/TC 17/SC 12,9599,[28049],[61299],"['en','ru']",9,"<p>ISO 10384:2008 applies to continuously hot-rolled carbon steel sheet as defined by chemical composition. The product is generally used in the heat-treated condition after hot or cold working, press forming or cutting by the customer. For example, the product is used for general machinery such as sprocket wheels, chain links, washers, knife blades and agricultural implements.</p><p>Steel sheet that is to be subjected to subsequent rerolling

18449,IS,,ISO 10385-1:2000,Measurement of water flow in closed conduits — Meters for hot water — Part 1: Specifications,Mesurage de débit d'eau dans les conduites fermées — Compteurs d'eau chaude — Partie 1: Spécifications,2000-11-30,1,['91.140.60'],ISO/TC 30/SC 7,9599,,[36682],"['en','fr']",14,

5515,IS,,ISO 1039:1975,Cinematography — Cores for motion-picture and magnetic film rolls — Dimensions,Cinématographie — Noyaux pour bobines de films cinématographiques et magnétiques — Dimensions,1975-05-01,1,['37.060.20'],ISO/TC 36,9599,,[5516],"['en','fr']",4,

5516,IS,,ISO 1039:1988,Cinematography — Cores for motion-picture and magnetic film rolls — Dimensions,Cinématographie — Noyaux pour films cinématographique et magnétique — Dimensions,1988-02-11,2,['37.060.20'],ISO/TC 36,9599,[5515],[23291],"['en','fr']",5,

18454,IS,,ISO 10390:1994,Soil quality — Determination of pH,Qualité du sol — Détermination du pH,1994-07-21,1,['13.080.10'],ISO/TC 190/SC 3,9599,,[40879],"['en','fr']",5,"<p>Specifies an instrumental method for the routine determination of pH using a glass electrode in a 1:5 (V/V) suspension of soil in water (pH-H₂O), in a solution of 1 mol/l potassium chloride (pH-KCl) or in a solution of 0,01 mol/l calcium chloride (pH-CaCl₂). Is applicable to all types of air-dried soil samples, e.g. pretreated according to ISO 11464.</p>"

40879,IS,,ISO 10390:2005,Soil quality — Determination of pH,Qualité du sol — Détermination du pH,2005-02-21,2,['13.080.10'],ISO/TC 190/SC 3,9599,[18454],[75243],"['en','fr']",7,"<p>ISO 10390:2005 specifies an instrumental method for the routine determination of pH using a glass electrode in a 1:5 (volume fraction) suspension of soil in water (pH in H₂O), in 1 mol/l potassium chloride solution (pH in KCl) or in 0,01 mol/l calcium chloride solution (pH in CaCl₂).</p><p>ISO 10390:2005 is applicable to all types of air-dried soil samples, for example pretreated in accordance with ISO 11464.</p>"

18456,IS,,ISO 10392:1992,Road vehicles with two axles — Determination of centre of gravity,Vehicules routiers à deux essieux — Détermination du centre de gravité,1992-06-11,1,['43.020'],ISO/TC 22,9599,,"[30083,52978]","['en','fr']",6,"<p>Specifies a method to determine the location of the centre of gravity. Other procedures may exist and be used, employing more elaborate and sophisticated methods and equipment, such as tilt-tables and cradles. Annex A gives a method of determining static loaded radius, Annex B includes a standard of test report.</p>"

18457,IS,,ISO 10396:1993,Stationary source emissions — Sampling for the automated determination of gas concentrations,Émissions de sources fixes — Échantillonnage pour la détermination automatique des concentrations de gaz,1993-09-30,1,['13.040.40'],ISO/TC 146/SC 1,9599,,[39508],"['en','fr']",13,"<p>The principle of the method specified is representative sampling of gases in a duct using two methods. In extractive sampling, the gases are conditioned to remove aerosols, particulate matter, and other interfering substances. In non-extractive sampling, the measurements are made in-situ, and no sample conditioning except filtering is required. The application is limited to the determination of O

18460,IS,,ISO 10399:1991,Sensory analysis — Methodology — Duo-trio test,Analyse sensorielle — Méthodologie — Essai duo-trio,1991-11-14,1,['67.240'],ISO/TC 34/SC 12,9599,,"[28638,34323]","['en','fr']",6,"<p>Specifies a method for determining whether there is a difference between two product samples. Describes the principle, the apparatus, the sampling, the preparation of specimens, the test procedure, and the contents of the test report. Annexes A, B and C are for information only.</p>"

34323,IS,,ISO 10399:2004,Sensory analysis — Methodology — Duo-trio test,Analyse sensorielle — Méthodologie — Essai duo-trio,2004-06-23,2,['67.240'],ISO/TC 34/SC 12,9599,[18460],[74219],"['en','fr']",19,"<p>ISO 10399:2004 describes a procedure for determining whether a perceptible sensory difference or similarity exists between samples of two products. The method is a forced-choice procedure. The method is applicable whether a difference exists in a single sensory attribute or in several attributes.</p><p>The method is statistically less efficient than the triangle test but is easier to perform by the assessors.</p><p>The method is applicable even when the nature of the difference is unknown

74219,IS,,ISO 10399:2017,Sensory analysis — Methodology — Duo-trio test,Analyse sensorielle — Méthodologie — Essai duo-trio,2017-12-07,3,['67.240'],ISO/TC 34/SC 12,9599,[34323],[88370],"['en','fr']",21,"<p>ISO 10399:2017 specifies a procedure for determining whether a perceptible sensory difference or similarity exists between samples of two products. The method is a forced-choice procedure. The method is applicable whether a difference exists in a single sensory attribute or in several attributes.</p><p>The method is statistically less efficient than the triangle test (described in ISO 4120) but is easier to perform by the assessors.</p><p>The method is applicable even when the nature of th

3773,IS,,ISO 104:1979,Rolling bearings — Thrust bearings with flat back faces — Boundary dimensions,Roulements — Butées à rondelles plates — Dimensions d'encombrement,1979-12-01,1,['21.100.20'],ISO/TC 4,9599,,[20518],"['en','fr']",12,

20518,IS,,ISO 104:1994,"Rolling bearings — Thrust bearings — Boundary dimensions, general plan","Roulements — Butées — Dimensions d'encombrement, plan général",1994-12-22,2,['21.100.20'],ISO/TC 4,9599,[3773],[33398],"['en','fr']",14,"<p>Cancels and replaces the first edition (1979). Specifies the major boundary dimensions of single-direction and double-direction thrust bearings with flat back faces. Gives the minimum bore diameters of housing washers and maximum outside diameters of shaft washers of bearings in dimension series 11, 12, 13, 14, 22, 23 and 24. Dimensions are given for corners indicated in figures 1 and 2.</p>"

33398,IS,,ISO 104:2002,"Rolling bearings — Thrust bearings — Boundary dimensions, general plan","Roulements — Butées — Dimensions d'encombrement, plan général",2002-02-28,3,['21.100.20'],ISO/TC 4,9599,[20518],[62974],"['en','fr']",15,

5517,IS,,ISO 1040:1983,Building construction — Modular coordination — Multimodules for horizontal coordinating dimensions,Construction immobilière — Coordination modulaire — Multimodules pour dimensions de coordination horizontale,1983-12-01,2,['91.010.30'],ISO/TC 59,9599,,[71507],"['en','fr']",1,"<p>Establishes the values of multimodules for horizontal coordinating dimensions for use in modular coordination of buildings. Applies to the design and construction of buildings of all types in accordance with the principles and rules of modular coordination laid down in ISO 2848. The international standardized values of multimodules for horizontal coordinating dimensions are 3 M, 6 M, 12 M, 30 M

18461,IS,,ISO 10400:1993,"Petroleum and natural gas industries — Formulae and calculation for casing, tubing, drill pipe and line pipe properties","Industries du pétrole et du gaz naturel — Formules et calculs relatifs aux propriétés des cuvelage, tubes de production, tiges de forage et tubes de conduites",1993-12-23,1,['75.180.10'],ISO/TC 67/SC 5,9599,,"[24930,44107]",['en'],37,"<p>Establishes the formulae. Requirements are specified in the fifth edition of API BULLETIN 5C3 (Bul 5C3), Juli 1989, which is adopted as ISO 10400. For the purposes of international standardization, modifications have been made that are outlined.</p>"

18466,IS,,ISO 10405:1993,Petroleum and natural gas industries — Care and use of casing and tubing,Industries du pétrole et du gaz naturel — Entretien et utilisation des tubes de cuvelage et de production,1993-08-05,1,['75.180.10'],ISO/TC 67/SC 5,9599,,[24931],['en'],50,

45977,IS,,ISO 10406-1:2008,Fibre-reinforced polymer (FRP) reinforcement of concrete — Test methods — Part 1: FRP bars and grids,Polymère renforcé par des fibres (PRF) pour l'armature du béton — Méthodes d'essai — Partie 1: Barres et grilles en PRF,2008-12-01,1,"['83.120','91.100.30']",ISO/TC 71/SC 6,9599,,[63657],['en'],40,<p>ISO 10406-1:2008 specifies test methods applicable to fibre-reinforced polymer (FRP) bars and grids as reinforcements or pre-stressing tendons in concrete.</p>

63657,IS,,ISO 10406-1:2015,Fibre-reinforced polymer (FRP) reinforcement of concrete — Test methods — Part 1: FRP bars and grids,Polymère renforcé par des fibres (PRF) pour l'armature du béton — Méthodes d'essai — Partie 1: Barres et grilles en PRF,2015-01-12,2,"['83.120','91.100.30']",ISO/TC 71/SC 6,9599,[45977],"[84321,86242]",['en'],39,<p>ISO 10406-1:2014 specifies test methods applicable to fibre-reinforced polymer (FRP) bars and grids as reinforcements or pre-stressing tendons in concrete.</p>

45978,IS,,ISO 10406-2:2008,Fibre-reinforced polymer (FRP) reinforcement of concrete — Test methods — Part 2: FRP sheets,Polymère renforcé par des fibres (PRF) pour l'armature du béton — Méthodes d'essai — Partie 2: Feuilles en PRF,2008-12-01,1,"['83.120','91.100.30']",ISO/TC 71/SC 6,9599,,[63658],['en'],34,<p>ISO 10406-2:2008 specifies test methods applicable to fibre-reinforced polymer (FRP) sheets for the upgrading of concrete members.</p>

63658,IS,,ISO 10406-2:2015,Fibre-reinforced polymer (FRP) reinforcement of concrete — Test methods — Part 2: FRP sheets,Polymère renforcé par des fibres (PRF) pour l'armature du béton — Méthodes d'essai — Partie 2: Feuilles en PRF,2015-01-15,2,"['83.120','91.100.30']",ISO/TC 71/SC 6,9599,[45978],[84320],['en'],35,<p>ISO 10406-2:2015 specifies test methods applicable to fibre-reinforced polymer (FRP) sheets for the upgrading of concrete members.</p>

18468,IS,,ISO 10407:1993,Petroleum and natural gas industries — Drilling and production equipment — Drill stem design and operating limits,Industries du pétrole et du gaz naturel — Étude des garnitures de forage et de leurs limites d'exploitation,1993-12-23,1,['75.180.10'],ISO/TC 67/SC 4,9599,,"[40801,62260,40800,50622,30855,24217]",['en'],92,"<p>Lays down the properties and establishes principles for the design and use. Requirements are specified in the fourteenth edition of API Recommended Practice 7G (RP 7G), August 1990, which is adopted as ISO 10407. For the purposes of international standardization, modifications have been made that are outlined.</p>"

18470,IS,,ISO 10409:1993,"Petroleum and natural gas industries — Application of cement lining to steel tubular goods, handling, installation and joining","Industries du pétrole et du gaz naturel — Mise en place des cheminages de ciment dans le cas de produits tubulaires en acier, manutention, installation et emboîture",1993-12-23,1,['75.180.10'],ISO/TC 67/SC 3,9599,,[24212],['en'],19,"<p>Lays down the minimum requirements. Requirements are specified in the second edition of API Recommended Practice 10E (RP 10E), July 1987, which is adopted as ISO 10409. For the purposes of international standardization, modifications have been made that are outlined.</p>"

31489,IS,,ISO 10414-1:2001,Petroleum and natural gas industries — Field testing of drilling fluids — Part 1: Water-based fluids,Industries du pétrole et du gaz naturel — Essais in situ des fluides de forage — Partie 1: Fluides aqueux,2001-03-29,1,['75.180.10'],ISO/TC 67/SC 3,9599,,[41939],['en'],62,

33019,IS,,ISO 10414-2:2002,Petroleum and natural gas industries — Field testing of drilling fluids — Part 2: Oil-based fluids,Industries du pétrole et du gaz naturel — Essais in situ des fluides de forage — Partie 2: Fluides à base d'huiles,2002-07-25,1,['75.180.10'],ISO/TC 67/SC 3,9599,,[41192],['en'],72,"<p>ISO 10414-2:2002 provides standard procedures for determining the following characteristics of oil-based drilling fluids:</p><ol><li>drilling fluid density (mud weight);</li><li>viscosity and gel strength;</li><li>filtration;</li><li>oil, water and solids contents;</li><li>alkalinity, chloride content and calcium content;</li><li>electrical stability;</li><li>lime and calcium contents,

34265,IS,,ISO 10416:2002,Petroleum and natural gas industries — Drilling fluids — Laboratory testing,Industries du pétrole et du gaz naturel — Fluides de forage — Essais en laboratoire,2002-11-22,1,"['75.100','75.180.10']",ISO/TC 67/SC 3,9599,,[41940],['en'],105,"<p>ISO 10416:2002 provides procedures for the laboratory testing of both drilling fluid materials and drilling fluid physical, chemical and performance properties. It is applicable to both water-based and oil-based drilling fluids, as well as the base or make-up fluid. </p><p>It is not intended as a detailed manual on drilling fluid control procedures. Recommendations regarding agitation and testing temperature are presented becaus

18479,IS,,ISO 10417:1993,"Petroleum and natural gas industries — Subsurface safety valve systems — Design, installation, operation and repair","Industries du pétrole et du gaz naturel — Systèmes de vannes de protection de fond de puits — Étude, installation, fonctionnement et réparation",1993-12-23,1,['75.180.10'],ISO/TC 67/SC 4,9599,,[24221],['en'],27,"<p>Lays down the recommended practice. Requirements are specified in the third edition of API Recommended Practice 14B (RP 14B), January 1990, which is adopted as ISO 10417. For the purposes of international standardization, modifications have been made that are outlined.</p>"

18480,IS,,ISO 10418:1993,"Petroleum and natural gas industries — Offshore production platforms — Analysis, design, installation and testing of basic surface safety systems","Industries du pétrole et du gaz naturel — Plates-formes de production en mer — Analyse, conception, installation et essais des systèmes essentiels de sécurité de surface",1993-12-23,1,['75.180.10'],ISO/TC 67/SC 6,9599,,"[24225,38067]",['en'],91,"<p>Lays down the recommended practice. Requirements are specified in the fourth edition of API Recommended Practice 14C (RP 14C), September 1986, which is adopted as ISO 10418. For the purposes of international standardization, modifications have been made that are outlined.</p>"

38067,IS,,ISO 10418:2003,"Petroleum and natural gas industries — Offshore production installations — Analysis, design, installation and testing of basic surface process safety systems","Industries du pétrole et du gaz naturel — Plates-formes de production en mer — Analyse, conception, installation et essais des systèmes essentiels de sécurité de surface",2003-10-06,2,['75.180.10'],ISO/TC 67/SC 6,9599,[18480],[55440],['en'],107,"<p>ISO 10418:2003 provides objectives, functional requirements and guidelines for techniques for the analysis, design and testing of surface process safety systems for offshore installations for the recovery of hydrocarbon resources. The basic concepts associated with

51283,IS,Cor,ISO 10418:2003/Cor 1:2008,"Petroleum and natural gas industries — Offshore production installations — Analysis, design, installation and testing of basic surface process safety systems — Technical Corrigendum 1","Industries du pétrole et du gaz naturel — Plates-formes de production en mer — Analyse, conception, installation et essais des systèmes essentiels de sécurité de surface — Rectificatif technique 1",2008-03-06,2,['75.180.10'],ISO/TC 67/SC 6,9599,,[55440],['en'],1,

18481,IS,,ISO 10419:1993,"Petroleum and natural gas industries — Drilling and production equipment — Installation, maintenance and repair of surface safety valves and underwater safety valves offshore","Industries du pétrole et du gaz naturel — Equipement de forage et de production — Installation, maintenance et réparation en mer des vannes de sécurité de surface et des vannes de sécurité sous-marines",1993-08-05,1,['75.180.10'],ISO/TC 67/SC 4,9599,,"[24239,24218]",['en'],18,"<p>Provides guidance for inspecting, installing, operating, maintaining and repairing surface safety valves and underwater safety valves. Requirements are specified in API Recommended Practice 14H (RP 14H), third editio

5519,IS,,ISO 1042:1983,Laboratory glassware — One-mark volumetric flasks,Verrerie de laboratoire — Fioles jaugées à un trait,1983-02-01,3,['17.060'],ISO/TC 48,9599,,[25484],"['en','fr']",3,

18482,IS,,ISO 10420:1994,Petroleum and natural gas industries — Flexible pipe systems for subsea and marine riser applications,Industries du pétrole et du gaz naturel — Systèmes de canalisations flexibles pour applications sous-marines et en milieu marin,1994-04-21,1,['75.200'],ISO/TC 67/SC 4,9599,,[38614],['en'],31,"<p>Provides guidelines for the design, analysis, testing, storage, handling and installation of flexible pipe systems used in a variety of offshore oil production applications. Requirements are specified in API Recommended Practice 17B (API RP 17B), first edition, June 1 1988, which is adopted as ISO 10420. For the purposes of international standardization, however, modification

18484,IS,,ISO 10422:1993,"Petroleum and natural gas industries — Threading, gauging, and thread inspection of casing, tubing and line pipe threads — Specification","Industries du pétrole et du gaz naturel — Filetage, calibrage et inspection des filetages des tubes de cuvelage, des tubes de production et de conduites — Spécifications",1993-08-05,1,['75.180.10'],ISO/TC 67/SC 5,9599,,[24224],['en'],126,"<p>Specifies dimensional requirements on thread and thread gauges, and covers the instruments and methods for the inspection of threads for line pipe, casing and tubing. Requirements are specified in API Specification STD 5B (STD 5B), thirteenth edition, May 31, 1988 which is adopted as ISO 1042

18485,IS,,ISO 10423:1994,"Petroleum and natural gas industries — Drilling and production equipment — Specification for valves, wellhead and Christmas tree equipment","Industries du pétrole et du gaz naturel — Équipement de forage et de production — Spécifications pour vannes, équipement pour têtes de puits et sapin de Noël",1994-07-07,1,['75.180.10'],ISO/TC 67/SC 4,9599,,[24239],['en'],227,"<p>Provides for the availability of safe, dimensionally and functionally interchangeable wellhead and christmas tree equipment by laying down the requirements for performance, design, materials, testing, inspections, welding, marking, handling, storing and shipping.</p>"

24239,IS,,ISO 10423:2001,Petroleum and natural gas industries — Drilling and production equipment — Wellhead and christmas tree equipment,Industries du pétrole et du gaz naturel — Équipement de forage et de production — Équipement pour têtes de puits et arbre de Noël,2001-08-16,2,['75.180.10'],ISO/TC 67/SC 4,9599,"[18495,18481,18485]",[39273],['en'],401,

39273,IS,,ISO 10423:2003,Petroleum and natural gas industries — Drilling and production equipment — Wellhead and christmas tree equipment,Industries du pétrole et du gaz naturel — Équipement de forage et de production — Équipement pour têtes de puits et arbre de Noël,2003-12-10,3,['75.180.10'],ISO/TC 67/SC 4,9599,[24239],[42757],['en'],403,"<p>ISO 10423:2003 specifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, purchasing, repair and remanufacture of wellhead and christmas tree equipment for use in the petroleum and natural gas industries. </p>

42757,IS,,ISO 10423:2009,Petroleum and natural gas industries — Drilling and production equipment — Wellhead and christmas tree equipment,Industries du pétrole et du gaz naturel — Équipement de forage et de production — Équipement pour têtes de puits et arbre de Noël,2009-12-11,4,['75.180.10'],ISO/TC 67/SC 4,9599,[39273],[79588],"['en','fr']",430,"<p>ISO 10423:2009 specifies requirements and gives recommendations for the performance, dimensional and functional interchangeability, design, materials, testing, inspection, welding, marking, handling, storing, shipment, purchasing, repair and remanufacture of wellhead and christmas tree equipment for use in the petroleum and natural gas industrie

33266,IS,,ISO 10424-1:2004,Petroleum and natural gas industries — Rotary drilling equipment — Part 1: Rotary drill stem elements,Industries du pétrole et du gaz naturel — Équipements de forage rotary — Partie 1: Éléments de forage rotary,2004-09-06,1,['75.180.10'],ISO/TC 67/SC 4,9599,,"[71713,59674]",['en'],66,"<p>ISO 10424-1:2004 specifies requirements for the following drill stem elements: upper and lower kelly valves; square and hexagonal kellys; drill stem subs; standard steel and non-magnetic drill collars; drilling and coring bits.</p><p>ISO 10424-1:2004 is not applicable to drill pipe and tool joints, rotary shouldered connection designs, thread gauging practice, or grand master, refe

43612,IS,,ISO 10424-2:2007,Petroleum and natural gas industries — Rotary drilling equipment — Part 2: Threading and gauging of rotary shouldered thread connections,Industries du pétrole et du gaz naturel — Équipements de forage rotary — Partie 2: Filetage et calibrage des connexions rotatives filetées à épaulement,2007-11-06,1,['75.180.10'],ISO/TC 67/SC 4,9599,,[57304],"['en','fr']",99,"<p>ISO 10424-2:2007 specifies requirements on rotary shouldered connections for use in petroleum and natural gas industries, including dimensional requirements on threads and thread gauges, stipulations on gauging practice, gauge specifications, as well as instruments and methods for inspection of thread conn

37526,IS,,ISO 10425:2003,Steel wire ropes for the petroleum and natural gas industries — Minimum requirements and terms of acceptance,Câbles en acier pour les industries du pétrole et du gaz naturel — Exigences minimales et conditions de réception,2003-08-19,1,"['77.140.65','75.180.10']",ISO/TC 105,9599,,[82835],"['en','fr']",56,<p>ISO 10425:2003 specifies the minimum requirements and terms of acceptance for the manufacture and testing of steel wire ropes not exceeding rope grade 2 160 for the petroleum and natural gas industries. </p>

32820,IS,,ISO 10426-1:2000,Petroleum and natural gas industries — Cements and materials for well cementing — Part 1: Specification,Industries du pétrole et du gaz naturel — Ciments et matériaux pour la cimentation des puits — Partie 1: Spécifications,2000-03-09,1,"['75.020','91.100.10']",ISO/TC 67/SC 3,9599,,[43022],"['en','fr']",40,

35080,IS,Amd,ISO 10426-1:2000/Amd 1:2002,Petroleum and natural gas industries — Cements and materials for well cementing — Part 1: Specification — Amendment 1,Industries du pétrole et du gaz naturel — Ciments et matériaux pour la cimentation des puits — Partie 1: Spécifications — Amendement 1,2002-08-22,1,"['75.020','91.100.10']",ISO/TC 67/SC 3,9599,,[43022],"['en','fr']",1,

43022,IS,,ISO 10426-1:2005,Petroleum and natural gas industries — Cements and materials for well cementing — Part 1: Specification,Industries du pétrole et du gaz naturel — Ciments et matériaux pour la cimentation des puits — Partie 1: Spécifications,2005-12-13,2,"['75.020','91.100.10']",ISO/TC 67/SC 3,9599,"[32820,35080,41963]",[46188],"['en','fr','ru']",39,"<p>ISO 10426-1:2005 specifies requirements and gives recommendations for eight classes of well cements, including their chemical and physical requirements and procedures for physical testing.</p><p>ISO 10426-1:2005 is applicable to well cement classes A, B, C, D, E and F, which are the products obtained by grinding Portland cement clink

35430,IS,,ISO 10426-3:2003,Petroleum and natural gas industries — Cements and materials for well cementing — Part 3: Testing of deepwater well cement formulations,Industries du pétrole et du gaz naturel — Ciments et matériaux pour la cimentation des puits — Partie 3: Essais de formulations de ciment pour puits en eau profonde,2003-08-19,1,"['75.020','91.100.10']",ISO/TC 67/SC 3,9599,,[74630],"['en','fr']",13,<p>ISO 10426-3:2003 provides procedures for testing well cements and cement blends for use in the petroleum and natural gas industries in a deepwater environment.</p>

38267,IS,,ISO 10426-5:2004,Petroleum and natural gas industries — Cements and materials for well cementing — Part 5: Determination of shrinkage and expansion of well cement formulations at atmospheric pressure,Industries du pétrole et du gaz naturel — Ciments et matériaux pour la cimentation des puits — Partie 5: Détermination du retrait et de l'expansion à la pression atmosphérique des formulations de ciments pour puits,2004-12-01,1,"['75.020','91.100.10']",ISO/TC 67/SC 3,9599,,[86804],"['en','fr']",13,"<p>ISO 10426-5:2004 provides the methods for the testing of well cement formulations to determine the dimension changes during the curing process (cement hydration) at atmospheric pressure o

32500,IS,,ISO 10427-1:2001,Petroleum and natural gas industries — Equipment for well cementing — Part 1: Casing bow-spring centralizers,Industries du pétrole et du gaz naturel — Équipement de cimentation de puits — Partie 1: Centreurs de tubes de cuvelage,2001-10-04,1,['75.180.10'],ISO/TC 67/SC 3,9599,[18489],[86807],"['en','fr']",10,"<p>This part of ISO 10427 provides minimum performance requirements, test procedures and marking requirements</p><p>for casing bow-spring centralizers for the petroleum and natural gas industries. The procedures provide verification</p><p>testing for the manufacturer's design, materials and process specifications, and periodic testing to confirm the</p><p>consi

18489,IS,,ISO 10427:1993,Petroleum and natural gas industries — Bow-spring casing centralizers — Specification,Industries du pétrole et du gaz naturel — Centreurs de tubes de cuvelage — Spécifications,1993-12-23,1,['75.180.10'],ISO/TC 67/SC 3,9599,,"[32501,32500]",['en'],8,"<p>Specifies testing procedures to verify the manufacturer's design, the materials and process for the construction. Requirements are specified in the fourth edition of API Specification 10D (Spec 10D), Januar 1991, which is adopted as ISO 10427. For the purposes of international standardization, modifications have been made that are outlined.</p>"

5522,IS,,ISO 1043-1:1987,Plastics — Symbols — Part 1: Basic polymers and their special characteristics,Plastiques — Symboles — Partie 1: Polymères de base et leurs caractéristiques spéciales,1987-12-17,1,['83.080.01'],ISO/TC 61/SC 1,9599,[5520],[5523],"['en','fr']",6,

5523,IS,,ISO 1043-1:1997,Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics,Plastiques — Symboles et abréviations — Partie 1: Polymères de base et leurs caractéristiques spéciales,1997-02-27,2,['83.080.01'],ISO/TC 61/SC 1,9599,[5522],[29758],"['en','fr']",11,<p>Gives uniform abbreviated terms for plastics and symbols for components of these terms. It includes only abbreviated terms that have come into established use. Replaces the first edition.</p>

29758,IS,,ISO 1043-1:2001,Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics,Plastiques — Symboles et termes abrégés — Partie 1: Polymères de base et leurs caractéristiques spéciales,2001-12-20,3,['83.080.01'],ISO/TC 61/SC 1,9599,[5523],[50590],"['en','fr']",11,

5520,IS,,ISO 1043:1978,Plastics — Symbols,Plastiques — Symboles,1978-12-01,2,['83.080.01'],ISO/TC 61,9599,,"[5522,5524,5525]","['en','fr']",4,

5524,IS,,ISO 1043-2:1988,Plastics — Symbols — Part 2: Fillers and reinforcing materials,Plastiques — Symboles — Partie 2: Charges et matériaux de renforcement,1988-10-13,1,"['59.100.01','83.080.01','83.040.30']",ISO/TC 61/SC 1,9599,[5520],[29756],"['en','fr']",2,

29756,IS,,ISO 1043-2:2000,Plastics — Symbols and abbreviated terms — Part 2: Fillers and reinforcing materials,Plastiques — Symboles et abréviations — Partie 2: Charges et matériaux de renforcement,2000-07-20,2,"['59.100.01','83.080.01','83.040.30']",ISO/TC 61/SC 1,9599,[5524],[52829],"['en','fr']",2,

5525,IS,,ISO 1043-3:1988,Plastics — Symbols — Part 3: Plasticizers,Plastiques — Symboles — Partie 3: Plastifiants,1988-10-13,1,['83.040.30'],ISO/TC 61/SC 1,9599,[5520],[20136],"['en','fr']",3,

20136,IS,,ISO 1043-3:1996,Plastics — Symbols and abbreviated terms — Part 3: Plasticizers,Plastiques — Symboles et abréviations — Partie 3: Plastifiants,1996-04-25,2,"['83.080.01','83.040.30']",ISO/TC 61/SC 1,9599,[5525],[61140],"['en','fr']",6,"<p>Provides uniform symbols for components of terms relating to plasticizers for plastics in terms of abbreviations. Contains in general, only those abbreviations that have come into established use in practice. Replaces the first edition.</p>"

24297,IS,,ISO 1043-4:1998,Plastics — Symbols and abbreviated terms — Part 4: Flame retardants,Plastiques — Symboles et abréviations — Partie 4: Ignifuges,1998-02-12,1,"['83.080.01','83.040.30']",ISO/TC 61/SC 1,9599,,[80286],"['en','fr']",3,

65281,IS,Amd,ISO 1043-4:1998/Amd 1:2016,Plastics — Symbols and abbreviated terms — Part 4: Flame retardants — Amendment 1: Code numbers,Plastiques — Symboles et abréviations — Partie 4: Ignifuges — Amendement 1: Numéros de code,2016-04-15,1,"['83.080.01','83.040.30']",ISO/TC 61/SC 1,9599,,[80286],"['en','fr']",1,

18493,IS,,ISO 10431:1993,Petroleum and natural gas industries — Pumping units — Specification,Industries du pétrole et du gaz naturel — Unités de pompage — Spécifications,1993-12-23,1,['75.180.10'],ISO/TC 67/SC 4,9599,,[24219],['en'],53,"<p>Lays down the specification covering the design and rating. Specifies the requirements for the dimensional characteristics, chemical and mechanical properties and gauging practice. Requirements are specified in the sixteenth edition of API Specification 11E (Spec 11E), October 1989, which is adopted as ISO 10431. For the purposes of international standardization, modifications have been made that are outlined.</p>"

18494,IS,,ISO 10432:1993,Petroleum and natural gas industries — Subsurface safety valve equipment — Specification,Industries du pétrole et du gaz naturel — Vannes de protection de fond de puits — Spécifications,1993-12-23,1,['75.180.10'],ISO/TC 67/SC 4,9599,,[24223],['en'],55,

24223,IS,,ISO 10432:1999,Petroleum and natural gas industries — Downhole equipment — Subsurface safety valve equipment,Industries du pétrole et du gaz naturel — Équipement de forage vertical — Vannes de protection de fond de puits,1999-11-04,2,['75.180.10'],ISO/TC 67/SC 4,9599,[18494],[36183],['en'],73,"<p>La présente Norme internationale a été élaborée à fin de définir les exigences minimales acceptables pour les équipements de vannes de sécurité de fond (SSSV). Elle concerne les vannes de sécurité de fond, les systèmes les performances ou l'interchangeabilité des équipements des vannes de sécurité de fond. Les systèmes de verrouillage, les mandrins d'ancrage et les vannes de sécurité de fo

18495,IS,,ISO 10433:1994,Petroleum and natural gas industries — Drilling and production equipment — Specification for wellhead surface safety valves and underwater safety valves for offshore service,Industries du pétrole et du gaz naturel — Équipement de forage et de production — Spécifications pour vannes de protection de tête de puits en surface et vannes de protection sous-marines pour utilisation en mer,1994-03-24,1,['75.180.10'],ISO/TC 67/SC 4,9599,,"[24239,24220]",['en'],66,"<p>Requirements are specified in API Specification 14D (API Spec 14D), ninth edition, June 1 1994, which is adopted as ISO 10433. For the purposes of international standardization, however, modifications shall appl

18496,IS,,ISO 10434:1998,Bolted bonnet steel gate valves for petroleum and natural gas industries,Robinets-vannes en acier à chapeau boulonné pour les industries du pétrole et du gaz naturel,1998-10-22,1,['75.180.20'],ISO/TC 153,9599,,"[34436,33230]","['en','fr']",26,

34436,IS,,ISO 10434:2004,"Bolted bonnet steel gate valves for the petroleum, petrochemical and allied industries","Robinets-vannes en acier à chapeau boulonné pour les industries du pétrole, de la pétrochimie et les industries connexes",2004-07-16,2,['75.180.20'],ISO/TC 153,9599,[18496],"[44202,78350]","['en','fr']",30,"<p>ISO 10434:2004 specifies the requirements for a heavy-duty series of bolted bonnet steel gate valves for petroleum refinery and related applications where corrosion, erosion and other service conditions would indicate a need for full port openings, heavy wall sections and large stem diameters. It sets forth the requirements for the following gate valve features: bolted bon

18498,IS,,ISO 10436:1993,Petroleum and natural gas industries — General-purpose steam turbines for refinery service,Industries du pétrole et du gaz naturel — Turbines à vapeur tous usages pour service en raffinerie,1993-12-23,1,"['75.180.20','27.040']",ISO/TC 67/SC 6,9599,,[24226],['en'],48,"<p>Specifies the minimum requirements. Requirements are specified in the third edition of API Standard 611 (Std 611), August 1988, which is adopted as ISO 10436. For the purposes of international standardization, modifications have been made that are outlined.</p>"

18499,IS,,ISO 10437:1993,Petroleum and natural gas industries — Special-purpose steam turbines for refinery service,Industries du pétrole et du gaz naturel — Turbines à vapeur d'usage spécial pour service en raffinerie,1993-12-23,1,"['75.180.20','27.040']",ISO/TC 67/SC 6,9599,,"[37864,24227]",['en'],59,"<p>Specifies the minimum requirements. Requirements are specified in the third edition of API Standard 612 (Std 612), November 1987, which is adopted as ISO 10437. For the purposes of international standardization, modifications have been made that are outlined.</p>"

33081,IS,,ISO 10438-1:2003,"Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 1: General requirements","Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes de lubrification, systèmes d'étanchéité, systèmes d'huile de régulation et leurs auxiliaires — Partie 1: Exigences générales",2003-12-09,1,['75.180.20'],ISO/TC 67/SC 6,9599,,[40481],['en'],52,"<p>ISO 10438-1:2003 specifies general requirements for lubrication, shaft-sealing and control-oil systems and auxiliaries for use in the petroleum, petrochemical and natural gas industries. It is intended to be used in conjunction with ISO 10438-2, ISO 10

33082,IS,,ISO 10438-2:2003,"Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 2: Special-purpose oil systems","Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes de lubrification, systèmes d'étanchéité, systèmes d'huile de régulation et leurs auxiliaires — Partie 2: Systèmes d'huile pour applications spéciales",2003-12-09,1,['75.180.20'],ISO/TC 67/SC 6,9599,,[40482],['en'],80,"<p>ISO 10438-2:2003 specifies requirements for oil systems supplying oil to compressors requiring seal oil, and to other machines, in special-purpose applications for use in the petroleum, petrochemical and natural gas indu

33085,IS,,ISO 10438-3:2003,"Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 3: General-purpose oil systems","Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes de lubrification, systèmes d'étanchéité, systèmes d'huile de régulation et leurs auxiliaires — Partie 3: Systèmes d'huile pour applications générales",2003-12-09,1,['75.180.20'],ISO/TC 67/SC 6,9599,,[40483],['en'],38,"<p>ISO 10438-3:2003 specifies requirements for oil systems supplying lubricating oil to machines in general-purpose applications for use in the petroleum, petrochemical and natural gas industries. It is intended to be used

33086,IS,,ISO 10438-4:2003,"Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 4: Self-acting gas seal support systems","Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes de lubrification, systèmes d'étanchéité, systèmes d'huile de régulation et leurs auxiliaires — Partie 4: Systèmes de soutien pour les étanchéités au gaz auto-actionnées",2003-12-09,1,['75.180.20'],ISO/TC 67/SC 6,9599,,[40484],['en'],36,"<p>ISO 10438-4:2003 specifies requirements for support systems for self-acting gas seals (dry gas seals) as described in ISO 10439, for use in the petroleum, petrochemical and natural gas industr

40484,IS,,ISO 10438-4:2007,"Petroleum, petrochemical and natural gas industries — Lubrication, shaft-sealing and control-oil systems and auxiliaries — Part 4: Self-acting gas seal support systems","Industries du pétrole, de la pétrochimie et du gaz naturel — Systèmes de lubrification, systèmes d'étanchéité, systèmes d'huile de régulation et leurs auxiliaires — Partie 4: Systèmes de soutien pour les étanchéités au gaz auto-actionnées",2007-12-03,2,['75.180.20'],ISO/TC 67/SC 6,9599,[33086],[82220],"['en','fr']",30,"<p>ISO 10438-4:2007 in conjunction with ISO 10438-1 specifies requirements for support systems for self-acting gas seals (dry gas seals), for example as described in ISO 10439 and I

33743,IS,,ISO 10439:2002,"Petroleum, chemical and gas service industries — Centrifugal compressors","Industries du pétrole, de la chimie et du gaz — Compresseurs centrifuges",2002-10-17,1,"['71.120.99','75.180.20']",ISO/TC 118/SC 1,9599,,"[56885,56886,56883,56884]","['en','fr']",119,"<p>ISO 10439 specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of centrifugal compressors for use in the petroleum, chemical and gas service industries. It is not applicable to machines that develop less than 35 kPa above atmospheric pressure, nor is it applicable to packaged, integrally geared centrifugal air compressors, w

5526,IS,,ISO 1044:1975,Industrial trucks — Traction batteries for electric trucks — Voltages,Chariots de manutention — Batteries de traction des chariots électriques — Tensions,1975-10-01,1,"['53.060','29.220.20']",ISO/TC 110,9599,,"[20078,5527]","['en','fr']",1,

5527,IS,,ISO 1044:1985,Industrial trucks — Traction batteries for electric trucks — Voltages,Chariots de manutention — Batteries de traction des chariots électriques — Tensions,1985-01-17,2,"['29.280','29.220','53.060']",ISO/TC 110,9599,[5526],[20078],"['en','fr']",1,

33744,IS,,ISO 10440-1:2000,Petroleum and natural gas industries — Rotary-type positive- displacement compressors — Part 1: Process compressors (oil-free),Industries du pétrole et du gaz naturel — Compresseurs volumétriques de type rotatif — Partie 1: Compresseurs de procédé (sans huile),2000-12-07,1,['75.180.20'],ISO/TC 118/SC 1,9599,,[36211],"['en','fr']",43,

18503,IS,,ISO 10441:1999,Petroleum and natural gas industries — Flexible couplings for mechanical power transmission — Special purpose applications,Industries du pétrole et du gaz naturel — Accouplements flexibles pour transmission de puissance mécanique — Applications spéciales,1999-03-18,1,['75.180.20'],ISO/TC 67/SC 6,9599,,[35107],['en'],35,"<p>La présente norme internationale s'applique à des accouplements de type à dents, ou à éléments métalliques flexibles, ou à arbre flexible (quillshaft) ou à élasticité torsionnelle (tortionally resilient-type). Elle ne s'applique pas à d'autres types d'accouplements comme ceux de types à embrayage (clutch), ou hydrauliques, ou à courants de Foucault

18509,IS,,ISO 10447:1991,"Welding — Peel and chisel testing of resistance spot, projection and seam welds","Soudage — Essais de pelage et de déboutonnage au burin appliqués aux soudures par résistance par points, par bossages et à la molette",1991-06-20,1,['25.160.40'],IIW,9599,,[37063],"['en','fr']",6,

37063,IS,,ISO 10447:2006,Resistance welding — Peel and chisel testing of resistance spot and projection welds,Soudage par résistance — Essais de déboutonnage au burin et de pelage appliqués aux soudures par résistance par points et par bossages,2006-07-12,2,['25.160.40'],IIW,9599,[18509],[61276],"['en','fr']",9,"<p>ISO 10447:2006 specifies the procedure and recommended tooling to be used for testing resistance spot and projection welds by means of peel and chisel tests. ISO 10447:2006 applies to welds made in two or more sheets in the thickness range of 0,5 mm to 3,0 mm.</p><p>The aim of these tests is to determine:</p><ul><li>weld size and failure type when the tests are used as destructive

61276,IS,,ISO 10447:2015,Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection welds,Soudage par résistance — Essais des soudures — Essais de pelage et de déboutonnage au burin appliqués aux soudures par résistance par points et par bossages,2015-02-10,3,['25.160.40'],ISO/TC 44/SC 6,9599,[37063],[82253],"['en','fr']",11,"<p>ISO 10447:2015 specifies the procedures and recommended tooling to be used for peel and chisel testing of resistance spot and projection welds. ISO 10447:2015 applies to welds made in two or more sheets in the thickness range of 0,5 mm to 3,0 mm.</p><p>The aim of these tests is to determine</p><p>- weld size and failure typ

18510,IS,,ISO 10448:1994,Agricultural tractors — Hydraulic pressure for implements,Tracteurs agricoles — Pression hydraulique pour les instruments,1994-07-21,1,['65.060.01'],ISO/TC 23/SC 4,9599,,[76703],"['en','fr']",2,"<p>Specifies the characteristics of the hydraulic pressure from agricultural tractors to connect hydraulic devices on implements, to permit interchangeable use of various types of implements using remote cylinders and other hydraulic devices. Applies to agricultural tractors intended for interchangeable implements.</p>"

30686,IS,,ISO 10451:2002,Dental implant systems — Contents of technical file,Systèmes d'implants dentaires — Contenu du dossier technique,2002-02-21,1,['11.060.15'],ISO/TC 106/SC 8,9599,[18513],[51071],"['en','fr']",7,"<p>This International Standard specifies requirements for the contents of a technical file to demonstrate the fulfilment of regulatory requirements for a dental implant and any prefabricated part thereof which remains in the mouth after surgery.</p><p>This International Standard is not applicable to instruments and other parts specifically made for the implant system but which do not remain in the mouth. However, documentation relating to these components may be included in th

51071,IS,,ISO 10451:2010,Dentistry — Contents of technical file for dental implant systems,Médecine bucco-dentaire — Contenu du dossier technique pour les systèmes d'implants dentaires,2010-06-07,2,['11.060.15'],ISO/TC 106/SC 8,9599,[30686],"[83843,78045]","['en','fr']",8,<p>ISO 10451:2010 specifies requirements for the contents of a technical file to demonstrate the fulfilment of regulatory requirements for a dental implant and any prefabricated part thereof that remains in the mouth after surgery.</p>

18516,IS,,ISO 10454:1993,Truck and bus tyres — Verifying tyre capabilities — Laboratory test methods,Pneumatiques pour camions et autobus — Vérification de l'aptitude des pneumatiques — Méthodes d'essai en laboratoire,1993-05-20,1,['83.160.10'],ISO/TC 31/SC 4,9599,,[87353],"['en','fr']",8,"<p>Of the test methods presented (strength test for the structure, endurance test), only some may be required depending on the type of tyre to be tested. The tests are carried out in a laboratory under controlled conditions. Applies to all truck and bus tyres.</p>"

18519,IS,,ISO 10456:1997,Thermal insulation — Building materials and products — Determination of declared and design thermal values,Isolation thermique — Matériaux et produits du bâtiment — Détermination des valeurs thermiques déclarées et utiles,1997-08-14,1,"['91.100.01','91.120.10']",ISO/TC 163/SC 2,9599,,[31326],"['en','fr']",16,

29844,IS,Cor,ISO 10456:1997/Cor 1:1997,Thermal insulation — Building materials and products — Determination of declared and design thermal values — Technical Corrigendum 1,Isolation thermique — Matériaux et produits du bâtiment — Détermination des valeurs thermiques déclarées et utiles — Rectificatif technique 1,1997-12-04,1,"['91.100.01','91.120.10']",ISO/TC 163/SC 2,9599,,[31326],"['en','fr']",2,

31326,IS,,ISO 10456:1999,Building materials and products — Procedures for determining declared and design thermal values,Matériaux et produits du bâtiment — Procédures pour la détermination des valeurs thermiques déclarées et utiles,1999-11-18,2,['91.120.10'],ISO/TC 163/SC 2,9599,"[29844,18519]",[40966],"['en','fr']",16,