Withdrawn and superseded ISO standards — page 7 of 246

18365,IS,,ISO 10318:1990,Geotextiles — Vocabulary,Géotextiles — Vocabulaire,1990-11-08,1,"['01.040.59','59.080.70']",ISO/TC 221,9599,,[41055],"['en','fr']",3,<p>Defines function and product terms applying to geotextiles and geotextile-related products.</p>

41055,IS,,ISO 10318:2005,Geosynthetics — Terms and definitions,Géosynthétiques — Termes et définitions,2005-06-30,2,"['01.040.59','59.080.70']",ISO/TC 221,9599,[18365],"[44886,44885]","['en','fr']",34,"<p>ISO 10318:2005 defines terms related to functions, products, properties and other terms, as well as symbols applying to geosynthetics. Definitions of terms not included in ISO 10318:2005 may be found in the standards describing appropriate test methods.</p>"

18366,IS,,ISO 10319:1993,Geotextiles — Wide-width tensile test,Géotextiles — Essai de traction des bandes larges,1993-04-15,1,['59.080.70'],ISO/TC 221,9599,,[36523],"['en','fr']",8,"<p>Applies to most geotextiles and also to geogrids, but in this case specimen dimensions may need to be altered. The index test method described covers the measurement of load elongation characteristics and includes procedures for the calculation of secant stiffness, maximum load per unit width and strain at maximum load. Singular points in the load-extension curve are also indicated.</p>"

36523,IS,,ISO 10319:2008,Geosynthetics — Wide-width tensile test,Géosynthétiques — Essai de traction des bandes larges,2008-05-27,2,['59.080.70'],ISO/TC 221,9599,[18366],[57696],"['en','fr']",11,"<p>ISO 10319:2008 describes an index test method for the determination of the tensile properties of geosynthetics, using a wide-width strip. The method is applicable to most geosynthetics, including woven geotextiles, nonwoven geotextiles, geocomposites, knitted geotextiles and felts. The method is also applicable to geogrids and similar open-structure geotextiles, but specimen dimensions might need to be altered. This test is not applicable to polymeric or bituminous geosynthetic barriers, while it

57696,IS,,ISO 10319:2015,Geosynthetics — Wide-width tensile test,Géosynthétiques — Essai de traction des bandes larges,2015-05-11,3,['59.080.70'],ISO/TC 221,9599,[36523],[82237],"['en','fr']",14,"<p>ISO 10319:2015 describes an index test method for the determination of the tensile properties of geosynthetics (polymeric, glass, and metallic), using a wide-width strip. It is applicable to most geosynthetics, including woven geotextiles, nonwoven geotextiles, geocomposites, knitted geotextiles, geonets, geomats, and metallic products. It is also applicable to geogrids and similar open-structure geotextiles, but specimen dimensions might need to be altered. It is not applicable to polymeric or b

5504,IS,,ISO 1032:1974,Coniferous sawn timber — Sizes — Terms and definitions,Sciages de bois résineux — Dimensions — Termes et définitions,1974-12-01,1,"['79.040','01.040.79']",ISO/TC 218,9599,,[77641],"['en','fr','ru']",6,<p>Provides for correct and adequate understanding of the terms relating to square-edged and unedged (waney) sawn timber. Replaces R 1032 and is in trilingual edition including the alphabetical index.</p>

18367,IS,,ISO 10320:1991,Geotextiles — Identification on site,Géotextiles — Identification sur site,1991-09-05,1,['59.080.70'],ISO/TC 221,9599,,[24661],"['en','fr']",2,

24661,IS,,ISO 10320:1999,Geotextiles and geotextile-related products — Identification on site,Géotextiles et produits apparentés — Identification sur site,1999-02-25,2,['59.080.70'],ISO/TC 221,9599,[18367],"[68728,59640]","['en','fr']",4,

18368,IS,,ISO 10321:1992,Geotextiles — Tensile test for joints/seams by wide-width method,Géotextiles — Essai de traction pour joints/coutures par la méthode de la bande large,1992-12-03,1,['59.080.70'],ISO/TC 221,9599,,[36524],"['en','fr']",7,"<p>The test method is based on gripping a specimen, 200 mm wide and containing a joint/seam, across its entire width in the clamps of a tensile testing machine, operated at a prescribed rate of extension, and application of a longitudinal force (perpendicular to the seam axis) until the joint/seam ruptures. Procedures for measuring the tensile properties of both conditioned and wet specimens are included.</p>"

18369,IS,,ISO 10322-1:1991,Ophthalmic optics — Semi-finished lens blanks — Part 1: Specifications for single-vision and multifocal lens blanks,Optique ophtalmique — Verres semi-finis — Partie 1: Spécifications pour les verres unifocaux et multifocaux,1991-12-12,1,['11.040.70'],ISO/TC 172,9599,,[22557],"['en','fr']",6,

20806,IS,Cor,ISO 10322-1:1991/Cor 1:1992,Ophthalmic optics — Semi-finished lens blanks — Part 1: Specifications for single-vision and multifocal lens blanks — Technical Corrigendum 1,Optique ophtalmique — Verres semi-finis — Partie 1: Spécifications pour les verres unifocaux et multifocaux — Rectificatif technique 1,1992-04-16,1,['11.040.70'],ISO/TC 172,9599,,[22557],"['en','fr']",1,

22557,IS,,ISO 10322-1:1996,Ophthalmic optics — Semi-finished spectacle lens blanks — Part 1: Specifications for single-vision and multifocal lens blanks,Optique ophtalmique — Verres de lunettes semi-finis — Partie 1: Spécifications pour les verres unifocaux et multifocaux,1996-01-25,2,['11.040.70'],ISO/TC 172/SC 7,9599,"[20806,18369]",[36639],"['en','fr']",6,<p>Specifies requirements for the optical and geometrical properties of semi-finished single-vision and multifocal lens blanks.</p>

36639,IS,,ISO 10322-1:2006,Ophthalmic optics — Semi-finished spectacle lens blanks — Part 1: Specifications for single-vision and multifocal lens blanks,Optique ophtalmique — Verres de lunettes semi-finis — Partie 1: Spécifications pour les verres unifocaux et multifocaux,2006-01-27,3,['11.040.70'],ISO/TC 172/SC 7,9599,[22557],[62496],"['en','fr']",9,<p>ISO 10322-1:2006 specifies requirements for the optical and geometrical properties of semi-finished single-vision and multifocal spectacle lens blanks. </p>

62496,IS,,ISO 10322-1:2016,Ophthalmic optics — Semi-finished spectacle lens blanks — Part 1: Specifications for single-vision and multifocal lens blanks,Optique ophtalmique — Verres de lunettes semi-finis — Partie 1: Spécifications pour les verres unifocaux et multifocaux,2016-03-03,4,['11.040.70'],ISO/TC 172/SC 7,9599,[36639],[86349],"['en','fr']",10,<p>ISO 10322-1:2016 specifies requirements for the optical and geometrical properties of all semi-finished single-vision and multifocal spectacle lens blanks.</p>

18370,IS,,ISO 10322-2:1991,Ophthalmic optics — Semi-finished lens blanks — Part 2: Specifications for progressive power lens blanks,Optique ophtalmique — Verres semi-finis — Partie 2: Spécifications pour les verres progressifs,1991-12-12,1,['11.040.70'],ISO/TC 172,9599,,[22558],"['en','fr']",6,

22558,IS,,ISO 10322-2:1996,Ophthalmic optics — Semi-finished spectacle lens blanks — Part 2: Specifications for progressive power lens blanks,Optique ophtalmique — Verres de lunettes semi-finis — Partie 2: Spécifications pour les verres progressifs,1996-01-25,2,['11.040.70'],ISO/TC 172/SC 7,9599,[18370],[36640],"['en','fr']",8,<p>Specifies requirements for the optical and geometrical properties of semi-finished progressive power lens blanks.</p>

36640,IS,,ISO 10322-2:2006,Ophthalmic optics — Semi-finished spectacle lens blanks — Part 2: Specifications for progressive power lens blanks,Optique ophtalmique — Verres de lunettes semi-finis — Partie 2: Spécifications pour les verres progressifs,2006-01-27,3,['11.040.70'],ISO/TC 172/SC 7,9599,[22558],[62495],"['en','fr']",8,<p>ISO 10322-2:2006 specifies requirements for the optical and geometrical properties of semi-finished progressive power spectacle lens blanks.</p>

62495,IS,,ISO 10322-2:2016,Ophthalmic optics — Semi-finished spectacle lens blanks — Part 2: Specifications for progressive-power and degressive-power lens blanks,Optique ophtalmique — Verres de lunettes semi-finis — Partie 2: Spécifications pour les verres progressifs et dégressifs,2016-03-03,4,['11.040.70'],ISO/TC 172/SC 7,9599,[36640],[86349],"['en','fr']",9,<p>ISO 10322-2:2016 specifies requirements for the optical and geometrical properties of semi-finished lens blanks with finished progressive-power and degressive-power surfaces.</p>

18371,IS,,ISO 10323:1991,Dental rotary instruments — Bore diameters for discs and wheels,Instruments rotatifs dentaires — Diamètres d'alésage des disques et roues,1991-11-07,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[55278],"['en','fr']",1,"<p>Specifies the following nominal bore diameters in order to achieve interchangeability between discs and wheels. Diameters in mm: 1,6; 1,8; 2,2; 3.</p>"

45958,IS,,ISO 10325:2009,"Fibre ropes — High modulus polyethylene — 8-strand braided ropes, 12-strand braided ropes and covered ropes","Cordages en fibres — Polyéthylène à haut module — Cordages 8 torons, cordages 12 torons et cordages avec couverture",2009-11-20,1,['59.080.50'],ISO/TC 38,9599,,[68944],"['en','fr']",5,"<p>ISO 10325:2009 specifies requirements for 8-strand braided ropes, for 12-strand braided ropes, and for covered rope constructions made of high modulus polyethylene (HMPE), and gives rules for their designation.</p>"

68944,IS,,ISO 10325:2018,"Fibre ropes — High modulus polyethylene — 8-strand braided ropes, 12-strand braided ropes and covered ropes","Cordages en fibres — Polyéthylène à haut module — Cordages tressés à 8 torons, cordages tressés à 12 torons et cordages avec couverture",2018-09-03,2,['59.080.50'],ISO/TC 38,9599,[45958],[90271],"['en','fr']",6,"<p>This document specifies requirements for 8-strand braided ropes, for 12-strand braided ropes, and for covered rope constructions for general purpose made of high modulus polyethylene (HMPE), and gives rules for their designation.</p><p>Many different types and grades of HMPE fibre exist which are commonly used to produce rope products. This docume

18374,IS,,ISO 10326-1:1992,Mechanical vibration — Laboratory method for evaluating vehicle seat vibration — Part 1: Basic requirements,Vibrations mécaniques — Méthode en laboratoire pour l'évaluation des vibrations du siège de véhicule — Partie 1: Exigences de base,1992-11-12,1,"['65.060.10','43.020','53.100','13.160']",ISO/TC 108/SC 4,9599,,"[67659,41432]","['en','fr']",7,"<p>Specifies the test method, the instrumentation requirements, the measuring assessment method and the way to report the test result.</p>"

37040,IS,Amd,ISO 10326-1:1992/Amd 1:2007,Mechanical vibration — Laboratory method for evaluating vehicle seat vibration — Part 1: Basic requirements — Amendment 1,Vibrations mécaniques — Méthode en laboratoire pour l'évaluation des vibrations du siège de véhicule — Partie 1: Exigences de base — Amendement 1,2007-09-10,1,"['65.060.10','43.020','53.100','13.160']",ISO/TC 108/SC 4,9599,,[67659],"['en','fr']",9,

55823,IS,Amd,ISO 10326-1:1992/Amd 2:2011,Mechanical vibration — Laboratory method for evaluating vehicle seat vibration — Part 1: Basic requirements — Amendment 2,Vibrations mécaniques — Méthode en laboratoire pour l'évaluation des vibrations du siège de véhicule — Partie 1: Exigences de base — Amendement 2,2011-12-13,1,"['65.060.10','43.020','53.100','13.160']",ISO/TC 108/SC 4,9599,,[67659],"['en','fr']",8,

33066,IS,,ISO 10326-2:2001,Mechanical vibration — Laboratory method for evaluating vehicle seat vibration — Part 2: Application to railway vehicles,Vibrations mécaniques — Méthode en laboratoire pour l'évaluation des vibrations du siège de véhicules — Partie 2: Application aux véhicules ferroviaires,2001-08-23,1,"['45.060.01','13.160']",ISO/TC 108/SC 4,9599,,"[76368,67655]","['en','fr']",17,"<p>This part of ISO 10326 defines specifications covering laboratory tests for seats designed for passengers and crew</p><p>in railway tractive and trailer vehicles.</p><p>It concerns tri-axial rectilinear vibration within the frequency range 0,5 Hz to 50 Hz. It specifies the input test</p><p>vibration t

18376,IS,,ISO 10327:1995,Aircraft — Certified aircraft container for air cargo — Specification and testing,Aéronefs — Conteneurs certifiés pour le fret aérien — Spécification et essais,1995-02-09,1,['55.180.30'],ISO/TC 20/SC 9,9599,,[62015],"['en','fr']",10,

18377,IS,,ISO 10328-1:1996,Prosthetics — Structural testing of lower-limb prostheses — Part 1: Test configurations,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Partie 1: Configurations d'essai,1996-12-12,1,['11.040.40'],ISO/TC 168,9599,,"[38708,33535]","['en','fr']",6,"<p>Gives test configurations for static and cyclic strength tests of lower-limb prostheses. Applies to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses. Defines coordinate systems, the location of a test sample and the position of the line of application of the test force.</p>"

18378,IS,,ISO 10328-2:1996,Prosthetics — Structural testing of lower-limb prostheses — Part 2: Test samples,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Partie 2: Échantillons d'essai,1996-12-12,1,['11.040.40'],ISO/TC 168,9599,,"[38708,33537]","['en','fr']",8,"<p>Describes procedures for static and cyclic strength tests of lower-limb prostheses. Applies to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses. Specifies types, selection, preparation and alignment of test samples and responsibilities for test preparation.</p>"

38708,IS,,ISO 10328:2006,Prosthetics — Structural testing of lower-limb prostheses — Requirements and test methods,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Exigences et méthodes d'essai,2006-09-14,1,['11.040.40'],ISO/TC 168,9599,"[23757,21912,18378,21913,18379,21911,2641,18377]",[70205],"['en','fr','ru']",136,"<p>ISO 10328:2005 specifies procedures for static and cyclic strength tests on lower-limb prostheses where, with one exception, compound loadings are produced by the application of a single test force. The compound loads in the test sample relate to the peak values of the components of loading which normally occur at different instants during th

18379,IS,,ISO 10328-3:1996,Prosthetics — Structural testing of lower-limb prostheses — Part 3: Principal structural tests,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Partie 3: Essais principaux de structure,1996-12-12,1,['11.040.40'],ISO/TC 168,9599,,"[38708,33538]","['en','fr']",16,"<p>Contains procedures for static and cyclic strength tests of lower-limb prostheses. Applies to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses. Specifies methods to be used in carrying out principal static and cyclic tests, requirements for accuracy of the tests and criteria to be met in order to secure compliance with this part of I

2641,IS,,ISO 10328-4:1996,Prosthetics — Structural testing of lower-limb prostheses — Part 4: Loading parameters of principal structural tests,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Partie 4: Paramètres de charge des essais principaux de structure,1996-12-12,1,['11.040.40'],ISO/TC 168,9599,,"[38708,33539]","['en','fr']",7,"<p>Describes procedures for static and cyclic strength tests of lower-limb prostheses. Applies to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses. Specifies the values of the test forces.</p>"

21913,IS,,ISO 10328-5:1996,Prosthetics — Structural testing of lower-limb prostheses — Part 5: Supplementary structural tests,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Partie 5: Essais supplémentaires de structure,1996-12-12,1,['11.040.40'],ISO/TC 168,9599,,"[38708,33540]","['en','fr']",11,"<p>Describes procedures for static and cyclic strength tests of lower-limb prostheses. Applies to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses. Specifies the values of the test forces and moments for the supplementary structural tests.</p>"

21912,IS,,ISO 10328-6:1996,Prosthetics — Structural testing of lower-limb prostheses — Part 6: Loading parameters of supplementary structural tests,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Partie 6: Paramètres de charge des essais supplémentaires de structure,1996-12-12,1,['11.040.40'],ISO/TC 168,9599,,"[38708,33541]","['en','fr']",6,"<p>Describes procedures for static and cyclic strength tests of lower-limb prostheses. Applies to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses. Specifies supplementary structural tests.</p>"

21911,IS,,ISO 10328-7:1996,Prosthetics — Structural testing of lower-limb prostheses — Part 7: Test submission document,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Partie 7: Document de soumission à l'essai,1996-12-12,1,['11.040.40'],ISO/TC 168,9599,,"[38708,33542]","['en','fr']",5,"<p>Describes procedures for static and cyclic strength tests of lower-limb prostheses. Applies to transtibial (below-knee), knee-disarticulation and transfemoral (above-knee) prostheses. Specifies the information that must be provided on the test submision document which accompanies each item for testing.</p>"

23757,IS,,ISO 10328-8:1996,Prosthetics — Structural testing of lower-limb prostheses — Part 8: Test report,Prothèses — Essais portant sur la structure des prothèses de membres inférieurs — Partie 8: Rapport d'essai,1996-12-26,1,['11.040.40'],ISO/TC 168,9599,,"[33543,38708]","['en','fr']",38,<p>Describes procedures for static and cyclic strength test for lower-limb prostheses. Specifies the information that shall be provided in the test report which is prepared for each test conducted in accordance with ISO 10328 and ISO 10328-4 and/or ISO 10328-5 and ISO 10328-6.</p>

41591,IS,,ISO 10329:2009,Coal — Determination of plastic properties — Constant-torque Gieseler plastometer method,Charbon — Détermination des propriétés plastiques — Méthode du plastomètre Gieseler à couple constant,2009-02-02,1,['73.040'],ISO/TC 27/SC 5,9599,,[70838],['en'],11,<p>ISO 10329:2009 specifies a method for obtaining a relative measure of the plastic behaviour of coal when heated under prescribed conditions. The method may be used to obtain values of the plastic properties of coals and blends used in carbonization and in other situations where determination of plastic behaviour of coals is of practical importance.</p>

70838,IS,,ISO 10329:2017,Coal — Determination of plastic properties — Constant-torque Gieseler plastometer method,Charbon — Détermination des propriétés plastiques — Méthode du plastomètre Gieseler à couple constant,2017-07-31,2,['73.040'],ISO/TC 27/SC 5,9599,[41591],[86996],['en'],13,<p>ISO 10329:2017 specifies a method for obtaining a relative measure of the plastic behaviour of coal when heated under prescribed conditions. The method is used to obtain values of the plastic properties of coals and blends used in carbonization and in other situations where determination of plastic behaviour of coals is of practical importance.</p><p>NOTE The empirical nature of this test requires prop

18381,IS,,ISO 10330:1992,"Photography — Synchronizers, ignition circuits and connectors for cameras and photoflash units — Electrical characteristics and test methods","Photographie — Interrupteurs synchronisés, circuits d'amorçage et connecteurs pour appareils de prise de vue et sources d'éclairs — Caractéristiques électriques et méthodes d'essai",1992-11-12,1,['37.040.10'],ISO/TC 42,9599,,"[36319,30846]",['en'],13,"<p>Requirements for synchronizer and ignition circuit are concerned with polarities of terminals, voltage across and current through terminals, for ignition circuit with operation, for synchronizer with dynamic characteristics and leakage current, and for cables with resistance,

18382,IS,,ISO 10331:1991,Photography — Unprocessed photographic films and papers — Storage practices,Photographie — Films et papiers photographiques non traités — Pratiques de stockage,1991-11-28,1,['37.040.20'],ISO/TC 42,9599,,[28008],"['en','fr']",3,<p>Gives guidance on the storage of radiation sensitive films and papers from the time of manufacturing to the time of processing. Applies to exposed or unexposed materials. Does not apply to processed films and papers.</p>

18383,IS,,ISO 10332:1994,Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Ultrasonic testing for the verification of hydraulic leak-tightness,Tubes en acier sans soudure et soudés (sauf à l'arc immergé) pour service sous pression — Contrôle par ultrasons pour la vérification de l'étanchéité,1994-02-03,1,"['77.040.20','23.040.10','77.140.75']",ISO/TC 17/SC 19,9599,,[44660],"['en','fr']",4,"<p>Specifies requirements and a method for ultrasonic testing. Is applicable to the inspection of tubes with an outside diameter greater than or equal to 168,3 mm, and with an outside diameter-to-thickness ratio greater than or equal to 5. By agreement between the purcha

18389,IS,,ISO 10338:1996,Optics and optical instruments — Contact lenses — Determination of curvature,Optique et instruments d'optique — Lentilles de contact — Détermination de la courbure,1996-07-11,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",15,

18390,IS,,ISO 10339:1997,Ophthalmic optics — Contact lenses — Determination of water content of hydrogel lenses,Optique ophtalmique — Lentilles de contact — Détermination de la teneur en eau des lentilles en hydrogel,1997-09-25,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34480],"['en','fr']",10,

18391,IS,,ISO 10340:1995,Optics and optical instruments — Contact lenses — Method for determining the extractable substances,Optique et instruments d'optique — Lentilles de contact — Méthode pour la détermination des substances extractibles,1995-07-27,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34480],"['en','fr']",5,<p>Specifies an analytical method for the quantitative determination of the substances extractable from contact lenses by Soxhlet extraction with different solvents.</p>

18392,IS,,ISO 10341:1997,Ophthalmic instruments — Refractor heads,Instruments ophtalmiques — Têtes de réfracteurs,1997-07-10,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[52931],"['en','fr']",8,

52931,IS,,ISO 10341:2009,Ophthalmic instruments — Refractor heads,Instruments ophtalmiques — Têtes de réfracteurs,2009-06-24,2,['11.040.70'],ISO/TC 172/SC 7,9599,[18392],"[58077,61824]","['en','fr']",9,"<p>ISO 10341:2009 specifies requirements and test methods for refractor heads used for the determination of refractive errors and binocular functions of the human eye. It takes priority over ISO 15004-1, if differences exist.</p>"

18393,IS,,ISO 10342:1997,Ophthalmic instruments — Eye refractometers,Instruments ophtalmiques — Réfractomètres,1997-10-02,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34276],"['en','fr']",6,

34276,IS,,ISO 10342:2003,Ophthalmic instruments — Eye refractometers,Instruments ophtalmiques — Réfractomètres,2003-05-16,2,['11.040.70'],ISO/TC 172/SC 7,9599,[18393],[54964],"['en','fr']",6,"<p>ISO 10342:2003, together with ISO 15004, specifies requirements and test methods for eye refractometers using an objective measuring principle.</p>"

18394,IS,,ISO 10343:1997,Ophthalmic instruments — Ophthalmometers,Instruments ophtalmiques — Ophtalmomètres,1997-07-10,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[52932],"['en','fr']",6,

52932,IS,,ISO 10343:2009,Ophthalmic instruments — Ophthalmometers,Instruments ophtalmiques — Ophtalmomètres,2009-06-24,2,['11.040.70'],ISO/TC 172/SC 7,9599,[18394],[59705],"['en','fr']",7,"<p>ISO 10343:2009, together with ISO 15004-1, specifies requirements and test methods for continuously or digitally indicating ophthalmometers. Certain types of ophthalmometer are capable of measuring radii of curvature of contact lenses as described in ISO 18369-3:2006, 4.1. It is assumed that the local corneal front surface and both contact lens surfaces are spherical or toroidal.</p><p>ISO 10343:2009 takes priority over ISO 15004-1, if differences exist.</p>"

18395,IS,,ISO 10344:1996,Optics and optical instruments — Contact lenses — Saline solution for contact lens testing,Optique et instruments d'optique — Lentilles de contact — Solution saline pour les essais des lentilles de contact,1996-08-22,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",3,"<p>Specifies a saline solution for use when conducting standardized tests to determine dimensions, physical, chemical and biological characteristics of contact lenses and contact lens materials. The solution is not intended for the purpose of packaging finished contact lenses.</p>"

18406,IS,,ISO 10349-1:1992,Photography — Photographic-grade chemicals — Test methods — Part 1: General,Photographie — Produits chimiques de qualité photographique — Méthodes d'essai — Partie 1: Généralités,1992-12-30,1,['37.040.30'],ISO/TC 42,9599,,[31338],['en'],6,"<p>Specifies criteria for reagents and materials, and addresses a number of general and common aspects involved in performing the tests given in subsequent parts of the standard. Annex A provides an index of International Standards on the specification of photographic-grade chemicals.</p>"

21265,IS,,ISO 10349-8:1992,Photography — Photographic-grade chemicals — Test methods — Part 8: Determination of volatile matter,Photographie — Produits chimiques de qualité photographique — Méthodes d'essai — Partie 8: Détermination des matières volatiles,1992-12-30,1,['37.040.30'],ISO/TC 42,9599,,[31339],['en'],2,"<p>The method is based on weighing the test portion into a dried weighing bottle, weighing the bottle and test portion after cooling in the desiccator to room temperature, and reweighing after drying in the desiccator.</p>"

5507,IS,,ISO 1035-1:1980,Hot-rolled steel bars — Part 1: Dimensions of round bars,Barres en acier laminées à chaud — Partie 1: Dimensions des barres rondes,1980-10-01,1,['77.140.60'],ISO/TC 17/SC 3,9599,,[89682],"['en','fr']",1,"<p>Specifies dimensions and tolerances of metric series hot-rolled steel round bars. A table shows diameters, sectional areas and masses per unit length.</p>"

5508,IS,,ISO 1035-2:1980,Hot-rolled steel bars — Part 2: Dimensions of square bars,Barres en acier laminées à chaud — Partie 2: Dimensions des barres carrées,1980-10-01,1,['77.140.60'],ISO/TC 17/SC 3,9599,,[89682],"['en','fr']",1,"<p>Specifies dimensions and tolerances of metric series hot-rolled steel square bars. Tables show width, corner radii, sectional areas and masses per unit length.</p>"

5509,IS,,ISO 1035-3:1980,Hot-rolled steel bars — Part 3: Dimensions of flat bars,Barres en acier laminées à chaud — Partie 3: Dimensions des barres plates,1980-11-01,1,['77.140.60'],ISO/TC 17/SC 3,9599,,[89682],"['en','fr']",1,<p>Specifies dimensions and tolerances of metric series hot-rolled steel flat bars. A table shows preferred and second-preference sizes of width and mass.</p>

5510,IS,,ISO 1035-4:1982,Hot-rolled steel bars — Part 4: Tolerances,Barres en acier laminées à chaud — Partie 4: Tolérances,1982-08-01,2,['77.140.60'],ISO/TC 17/SC 3,9599,,[89682],"['en','fr']",3,"<p>Specifies metric dimensional tolerances applicable to hot-rolled steel bars supplied in straight lengths in the form of round bars, square bars, hexagonal bars, octagonal bars, flat bars. The tolerances achievable by the manufacturer may vary with the steel types. Specifies several tolerance classes.</p>"

25170,IS,,ISO 10350-1:1998,Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials,Plastiques — Acquisition et présentation de caractéristiques intrinsèques comparables — Partie 1: Matériaux pour moulage,1998-11-19,1,['83.080.20'],ISO/TC 61/SC 2,9599,[18407],[39597],"['en','fr']",10,

39597,IS,,ISO 10350-1:2007,Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials,Plastiques — Acquisition et présentation de caractéristiques intrinsèques comparables — Partie 1: Matériaux pour moulage,2007-07-09,2,['83.080.20'],ISO/TC 61/SC 2,9599,[25170],[70314],"['en','fr']",10,"<p>ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented

59439,IS,Amd,ISO 10350-1:2007/Amd 1:2014,Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials — Amendment 1,Plastiques — Acquisition et présentation de caractéristiques intrinsèques comparables — Partie 1: Matériaux pour moulage — Amendement 1,2014-06-05,2,['83.080.20'],ISO/TC 61/SC 2,9599,,[70314],"['en','fr']",1,

70314,IS,,ISO 10350-1:2017,Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials,Plastiques — Acquisition et présentation de caractéristiques intrinsèques comparables — Partie 1: Matériaux pour moulage,2017-10-11,3,['83.080.20'],ISO/TC 61/SC 2,9599,"[39597,59439]",[85826],"['en','fr']",11,"<p>The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions. The properties included

18407,IS,,ISO 10350:1993,Plastics — Acquisition and presentation of comparable single-point data,Plastiques — Acquisition et présentation de caractéristiques intrinsèques comparables,1993-12-23,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[25170],"['en','fr']",7,"<p>Identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value although in certain cases properties are represented by two values obtained under different test conditions. The properties included are those presented conventionally in manufacturer's data sheets. Applies predominantly to those plastic

28168,IS,,ISO 10350-2:2001,Plastics — Acquisition and presentation of comparable single-point data — Part 2: Long-fibre-reinforced plastics,Plastiques — Acquisition et présentation de caractéristiques intrinsèques comparables — Partie 2: Plastiques renforcés par de longues fibres,2001-06-28,1,['83.120'],ISO/TC 61/SC 2,9599,,[45088],"['en','fr']",8,

45088,IS,,ISO 10350-2:2011,Plastics — Acquisition and presentation of comparable single-point data — Part 2: Long-fibre-reinforced plastics,Plastiques — Acquisition et présentation de caractéristiques intrinsèques comparables — Partie 2: Plastiques renforcés par de longues fibres,2011-02-17,2,['83.120'],ISO/TC 61/SC 2,9599,[28168],[70315],"['en','fr']",9,"<p>ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions or along differe

18408,IS,,ISO 10351:1992,Plastics — Determination of the combustibility of specimens using a 125 mm flame source,Plastiques — Détermination de la combustibilité d'éprouvettes soumises à une flamme de 125 mm comme source d'allumage,1992-11-25,1,"['83.080.01','13.220.40']",ISO/TC 61/SC 4,9599,,[26272],"['en','fr']",11,

18409,IS,,ISO 10352:1991,Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of mass per unit area,Plastiques renforcés de fibres — Préimprégnés — Détermination de la masse surfacique,1991-10-17,1,['83.120'],ISO/TC 61/SC 13,9599,,[23133],"['en','fr']",2,

23133,IS,,ISO 10352:1997,Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of mass per unit area,Plastiques renforcés — Préimprégnés — Détermination de la masse surfacique,1997-01-22,2,['83.120'],ISO/TC 61/SC 13,9599,[18409],[50602],"['en','fr']",6,"<p>Describes a method for the determination of the mass per unit area of moulding compounds and preimpregnated sheets, tapes, fabrics and mats (prepregs). Applicable to prepregs irrespective of which reinforcement (aramid, carbon, glass, etc.) or which type of matrix (thermosetting or thermoplastic) is used.</p>"

50602,IS,,ISO 10352:2010,Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of mass per unit area,Plastiques renforcés de fibres — Mélanges à mouler et préimprégnés — Détermination de la masse surfacique,2010-11-25,3,['83.120'],ISO/TC 61/SC 13,9599,[23133],[70572],"['en','fr']",7,"<p>ISO 10352:2010 specifies a method for the determination of the mass per unit area of sheet moulding compound and preimpregnated unidirectional sheet, tape, fabric and mats.</p><p>Unless stated to the contrary in the relevant material specification, it is applicable to prepregs in which any type of reinforcement (aramid, carbon, glass, etc.) and any type of matrix (thermosetting or thermo

18412,IS,,ISO 10355:1994,Mopeds — Positioning of lighting and light-signalling devices,Cyclomoteurs — Position des dispositifs d'éclairage et de signalisation lumineuse,1994-11-24,1,['43.140'],ISO/TC 22,9599,,[33456],"['en','fr']",5,"<p>Specifies the requirements for the positioning of lighting and ligth-signalling devices when fitted to a moped, as defined in ISO 3833. Does not specify the installation of any of these devices.</p>"

5511,IS,,ISO 1036:1976,Textile machinery and accessories — Dyeing and finishing machines — Definition of left and right sides,Matériel pour l'industrie textile — Machines de teinture et d'apprêt — Définition des côtés droit et gauche,1976-08-01,1,['59.120.50'],ISO/TC 72,9599,,[5512],"['en','fr']",2,

56662,IS,,ISO 10360-10:2016,Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring systems (CMS) — Part 10: Laser trackers for measuring point-to-point distances,Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des systèmes à mesurer tridimensionnels (SMT) — Partie 10: Laser de poursuite pour mesurer les distances de point à point,2016-04-04,1,['17.040.30'],ISO/TC 213,9599,,[77155],"['en','fr']",42,"<p>ISO 10360-10:2016 specifies the acceptance tests for verifying the performance of a laser tracker by measuring calibrated test lengths, test spheres and flats according to the specifications of the

18419,IS,,ISO 10360-2:1994,Coordinate metrology — Part 2: Performance assessment of coordinate measuring machines,Métrologie par coordonnées — Partie 2: Évaluation des performances des machines à mesurer tridimensionnelles,1994-01-20,1,['17.040.30'],ISO/TC 213,9599,,[29646],"['en','fr']",9,"<p>Specifies the acceptance test, which verifies that the performance of a coordinate measuring machine (CMM) and its probing system is as stated by the manufacturer, the reverification test, which enables the user to reverify CMM performance and the CMM probing system periodically, and the interim check, which enables the user to make checks on a CMM and the CMM probing system between regular reverificat

29646,IS,,ISO 10360-2:2001,Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 2: CMMs used for measuring size,Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) — Partie 2: MMT utilisées pour les mesures de tailles,2001-12-20,2,['17.040.30'],ISO/TC 213,9599,[18419],[40954],"['en','fr']",11,

25893,IS,,ISO 10360-4:2000,Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode,Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) — Partie 4: MMT utilisées en mode de mesure par scanning,2000-03-30,1,['17.040.30'],ISO/TC 213,9599,,[73431],"['en','fr']",12,

37695,IS,Cor,ISO 10360-4:2000/Cor 1:2002,Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 4: CMMs used in scanning measuring mode — Technical Corrigendum 1,Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) — Partie 4: MMT utilisées en mode de mesure par scanning — Rectificatif technique 1,2002-11-20,1,['17.040.30'],ISO/TC 213,9599,,[73431],"['en','fr']",2,

28094,IS,,ISO 10360-5:2000,Geometrical Product Specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using multiple-stylus probing systems,Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) — Partie 5: MMT utilisant des systèmes de palpage à stylets multiples,2000-12-21,1,['17.040.30'],ISO/TC 213,9599,,[40956],"['en','fr']",12,

40956,IS,,ISO 10360-5:2010,Geometrical product specifications (GPS) — Acceptance and reverification tests for coordinate measuring machines (CMM) — Part 5: CMMs using single and multiple stylus contacting probing systems,Spécification géométrique des produits (GPS) — Essais de réception et de vérification périodique des machines à mesurer tridimensionnelles (MMT) — Partie 5: MMT utilisant des systèmes de palpage à stylet simple ou à stylets multiples,2010-09-10,2,['17.040.30'],ISO/TC 213,9599,"[28094,52076]",[73431],"['en','fr']",30,"<p>ISO 10360-5:2010 specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs usi

26837,IS,,ISO 10361:2000,Textile floor coverings — Production of changes in appearance by means of Vettermann drum and hexapod tumbler testers,Revêtements de sol textiles — Production de changements d'aspect au moyen d'essais au tambour Vettermann et au tambour pour hexapode,2000-07-06,1,['97.150'],ISO/TC 219,9599,[18420],"[42360,37181]","['en','fr']",9,

42360,IS,,ISO 10361:2012,Textile floor coverings — Production of changes in appearance by means of Vettermann drum and hexapod tumbler tester,Revêtements de sol textiles — Production de changements d'aspect au moyen d'essais au tambour Vettermann et au tambour pour hexapode,2012-03-02,2,['97.150'],ISO/TC 219,9599,[26837],[61692],['en'],9,

61692,IS,,ISO 10361:2015,Textile floor coverings — Production of changes in appearance by means of Vettermann drum and hexapod tumbler tester,Revêtements de sol textiles — Production de changements d’aspect au moyen d’essais au tambour Vettermann et au tambour d'essai pour hexapode,2015-01-20,3,['97.150'],ISO/TC 219,9599,[42360],"[71191,87371,87372]","['en','fr']",10,<p>ISO 10361:2015 describes procedures that use the mechanical action of a Vettermann drum or a hexapod tumbler tester to produce changes in appearance (surface structure and colour) to all types of textile floor coverings. It does not include pilling or colour changes due to other actions.</p><p>Changes produced by these drum t

18421,IS,,ISO 10362-1:1991,Cigarettes — Determination of water in smoke condensates — Part 1: Gas-chromatographic method,Cigarettes — Dosage de l'eau dans les condensats de fumée — Partie 1: Méthode par chromatographie en phase gazeuse,1991-09-19,1,['65.160'],ISO/TC 126,9599,,[28322],"['en','fr']",4,

28322,IS,,ISO 10362-1:1999,Cigarettes — Determination of water in smoke condensates — Part 1: Gas-chromatographic method,Cigarettes — Dosage de l'eau dans les condensats de fumée — Partie 1: Méthode par chromatographie en phase gazeuse,1999-12-16,2,['65.160'],ISO/TC 126,9599,[18421],[72630],"['en','fr']",7,

54404,IS,Amd,ISO 10362-1:1999/Amd 1:2011,Cigarettes — Determination of water in smoke condensates — Part 1: Gas-chromatographic method — Amendment 1: .,Cigarettes — Dosage de l'eau dans les condensats de fumée — Partie 1: Méthode par chromatographie en phase gazeuse — Amendement 1: .,2011-07-21,2,['65.160'],ISO/TC 126,9599,,[72630],"['en','fr']",1,

18422,IS,,ISO 10362-2:1994,Cigarettes — Determination of water in smoke condensates — Part 2: Karl Fischer method,Cigarettes — Dosage de l'eau dans les condensats de fumée — Partie 2: Méthode de Karl Fischer,1994-01-27,1,['65.160'],ISO/TC 126,9599,,[60153],"['en','fr']",4,"<p>The principle of the method specified is dissolving the smoke condensate from the mainstream smoke in a solvent and determination of the water content of an aliquot of the solution by titration with standardized Karl Fischer reagent. The smoking of cigarettes and collection of mainstream smoke are normally carried out in accordance with ISO 4387. However, the method is also applicable to the determination of water in sm

54406,IS,Amd,ISO 10362-2:1994/Amd 1:2011,Cigarettes — Determination of water in smoke condensates — Part 2: Karl Fischer method — Amendment 1,Cigarettes — Dosage de l'eau dans les condensats de fumée — Partie 2: Méthode de Karl Fischer — Amendement 1,2011-07-21,1,['65.160'],ISO/TC 126,9599,,[60153],"['en','fr']",1,

18424,IS,,ISO 10364:1993,Adhesives — Determination of working life (pot life) of multi-component adhesives,Adhésifs — Détermination du délai d'utilisation (vie en pot) d'adhésifs multicomposants,1993-06-17,1,['83.180'],ISO/TC 61/SC 11,9599,,[39603],"['en','fr']",3,<p>Is intended to determine whether the working life conforms to the minimum specified working life required of an adhesive by viscosity tests or by bond strength tests or by both. The working life is determined by measuring the viscosity and/or bond strength at specified intervals. The time at which the bond strength drops to a specified level and/or a specified change in viscosity is obtained is considered the working life of the

39603,IS,,ISO 10364:2007,Structural adhesives — Determination of the pot life (working life) of multi-component adhesives,Adhésifs structuraux — Détermination de la durée de vie en pot (délai d'utilisation) d'adhésifs multicomposants,2007-08-28,2,['83.180'],ISO/TC 61/SC 11,9599,[18424],[60414],['en'],7,"<p>ISO 10364:2007 specifies methods for determining the pot life of multi-component adhesives in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.</p><p>The test methods described are suitable for assessing all multi-component adhesives, and especially epoxy-based and polyurethane-based adhesives, but they are not suitab

60414,IS,,ISO 10364:2015,Structural adhesives — Determination of the pot life (working life) of multi-component adhesives,Adhésifs structuraux — Détermination de la vie en pot (durée d'utilisation) des adhésifs multicomposants,2015-09-18,3,['83.180'],ISO/TC 61/SC 11,9599,[39603],[82747],"['en','fr']",8,"<p>ISO 10364:2015 specifies methods for determining the pot life of multi-part adhesives in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.</p><p>For the purposes of simplification, the term 'pot life' is deemed to have the same meaning as 'working life' and will be used to represent both throughout this International

18425,IS,,ISO 10365:1992,Adhesives — Designation of main failure patterns,Adhésifs — Désignation des principaux faciès de rupture,1992-12-17,1,['83.180'],ISO/TC 61/SC 11,9599,,[80800],"['en','fr']",3,"<p>Specifies the designations and illustrates, through diagrams, their respective appearances. It applies to all mechanical tests performed on a bonded assembly, regardless of the nature of the adherends and adhesive which make up the assembly.</p>"

18426,IS,,ISO 10366-1:1993,Plastics — Methyl methacrylate/acrylonitrile/butadiene/styrene (MABS) moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Méthylméthacrylate/acrylonitrile/butadiène/ styrène (MABS) pour moulage et extrusion — Partie 1: Système de désignation et base de spécification,1993-12-23,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[33493],"['en','fr']",7,"<p>The types of MABS plastics are differentiated from each other by a classification system based on appropriate levels of the designatory properties Vicat softening temperature, melt flow rate, impact strength, flexural modulus and on information about basic polymer parameters, i

33493,IS,,ISO 10366-1:2002,Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Méthacrylate de méthyle-acrylonitrile-butadiène-styrène (MABS) pour moulage et extrusion — Partie 1: Système de désignation et base de spécifications,2002-10-10,2,['83.080.20'],ISO/TC 61/SC 9,9599,[18426],[63850],"['en','fr']",8,"<p><b>1.1 </b>ISO 10366-1:2002 establishes a system of designation for methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials, which may be used as the basis for specifications.</p><p><b>1.2 </b>The types of MABS plastic are differe

18427,IS,,ISO 10366-2:1994,Plastics — Methyl methacrylate/ acrylonitrile/butadiene/styrene (MABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Méthylméthacrylate/acrylonitrile/butadiène/styrène (MABS) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés,1994-10-20,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[33335],"['en','fr']",6,<p>Specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of MABS moulding and extrusion materials. Gives requirements for handling test material and for conditioning both the test material befo

33335,IS,,ISO 10366-2:2003,Plastics — Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Méthacrylate de méthyle-acrylonitrile-butadiène-styrène (MABS) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés,2003-11-28,2,['83.080.20'],ISO/TC 61/SC 9,9599,[18427],[77540],"['en','fr']",7,"<p>ISO 10366-2:2003 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of MABS moulding and extrusion materials. Requirements for handling test material and for conditioning both

18429,IS,,ISO 10368:1992,Freight thermal containers — Remote condition monitoring,Conteneurs à caractéristiques thermiques — Système de pilotage à distance des groupes frigorifiques,1992-07-23,1,['55.180.10'],ISO/TC 104,9599,,[36595],['en'],88,"<p>Establishes the information and interfaces required to permit complying central monitoring and control systems employed by one carrier or terminal to interface and communicate with complying remote communication devices of differing manufacture and configuration used by other carriers and terminals. Gives the data-logging formats and message protocols, performance requirements for the monitoring, communication and control system, and the system com

5513,IS,,ISO 1037:1982,Textile machinery and accessories — Beams for dyeing slivers and yarn — Terminology and main dimensions,Matériel pour l'industrie textile — Ensouples de teinture pour fibres et filés — Terminologie et dimensions principales,1982-07-01,1,['59.120.20'],ISO/TC 72/SC 3,9599,,[21955],"['en','fr']",3,

18431,IS,,ISO 10370:1993,Petroleum products — Determination of carbon residue — Micro method,Produits pétroliers — Détermination du résidu de carbone — Méthode micro,1993-09-02,1,['75.080'],ISO/TC 28,9599,,[57081],"['en','fr']",9,"<p>The principle of the method specified is placing a weighed aliquot of the oil sample in a glas vial, heating it to 500 °C under an inert (nitrogen) gas stream in a controlled manner for a specific time, sweeping away the volatiles formed during the reactions by the inert gas, weighing the carbonaceous residue remaining. The method may be used to determine amounts of carbon residues in the range of 0,10 % (m/m) to 30,0 % (m/m), left after evaporation and pyrolysi

27881,IS,Cor,ISO 10370:1993/Cor 1:1996,Petroleum products — Determination of carbon residue — Micro method — Technical Corrigendum 1,Produits pétroliers — Détermination du résidu de carbone — Méthode micro — Rectificatif technique 1,1996-09-15,1,['75.080'],ISO/TC 28,9599,,[57081],['fr'],,

18439,IS,,ISO 10378:1994,Copper sulfide concentrates — Determination of gold and silver contents — Fire assay gravimetric and flame atomic absorption spectrometric method,Concentrés de sulfure de cuivre — Dosage de l'or et de l'argent — Méthode gravimétrique par essai au feu et spectrométrie d'absorption atomique dans la flamme,1994-06-16,1,['73.060.99'],ISO/TC 183,9599,,[34528],"['en','fr']",27,"<p>Fire assaying comprises the following steps: crucible fusion, cupellation, parting (followed by flame atomic absorption spectrometry), retreatment, correction for blank contamination. The method is applicable for copper sulfide concentrates containing 15 % (m/m) to 60 % (m/m) copper, mainly in th

34528,IS,,ISO 10378:2005,"Copper, lead and zinc sulfide concentrates — Determination of gold and silver — Fire assay gravimetric and flame atomic absorption spectrometric method","Concentrés de sulfure de cuivre, de plomb et de zinc — Dosage de l'or et de l'argent — Méthode gravimétrique par essai au feu et spectrométrie d'absorption atomique dans la flamme",2005-06-29,2,['73.060.99'],ISO/TC 183,9599,[18439],[68189],['en'],52,"<p>ISO 10378:2005 specifies a fire assay gravimetric and flame atomic absorption spectrometric method for the determination of the mass fraction of gold and silver in copper, lead and zinc sulfide concentrates.</p>"

18441,IS,,ISO 10380:1994,Corrugated flexible metallic hose and hose assemblies,Tuyaux et tuyauteries métalliques flexibles onduleux,1994-04-21,1,['23.040.70'],ISO/TC 5/SC 11,9599,,[30176],"['en','fr']",9,"<p>Specifies the requirements for the design, manufacture and testing. Also specifies nominal sizes from DN 6 to DN 300, nominal pressures from PN 2,5 to PN 250, two types of construction and two types of flexibility of hose assembly. The corrugated hose assemblies specified are suitable for the majority of possible applications. They are however not designed for applications involving axial compression or extension, or external pressure.</p>"

30176,IS,,ISO 10380:2003,Pipework — Corrugated metal hoses and hose assemblies,Tuyauteries — Tuyaux et tuyauteries métalliques flexibles onduleux,2003-01-22,2,['23.040.70'],ISO/TC 5/SC 11,9599,[18441],[52943],"['en','fr']",16,"<p>ISO 10380:2002 specifies the requirements for the design, manufacture and testing of corrugated metal hoses and hose assemblies for general purposes.</p><p>It also specifies sizes from DN 4 to DN 300, pressures from PN 0,5 to PN 250, pressure derating factors for elevated temperatures, two methods of construction and three types of flexibility of hose assembly.</p>"