Withdrawn and superseded ISO standards — page 50 of 246

40530,IS,,ISO 15314:2004,Plastics — Methods for marine exposure,Plastiques — Méthodes d'exposition aux intempéries marines,2004-11-09,1,['83.080.01'],ISO/TC 61/SC 6,9599,,[74668],"['en','fr']",12,"<p>ISO 15314:2004 describes three methods for the exposure of plastics in a marine environment. Method A covers exposures where specimens float on the surface, method B covers exposures where specimens are partially immersed and method C covers exposures where specimens are completely immersed. Although intended for marine (salt water) exposure, the methodology might be used with outdoor brackish water and fresh-water exposures as well.</p><p>Method A is particularly applicable to enhanced-degradab

27228,IS,,ISO 15319:1999,Recycled pulps — Estimation of visible contraries by instrumental means using reflected light,Pâtes recyclées — Estimation des défauts visibles par des moyens automatiques en lumière réfléchie,1999-12-16,1,['85.040'],ISO/TC 6,9599,,"[41351,39994]","['en','fr']",11,

35170,IS,,ISO 15320:2003,"Pulp, paper and board — Determination of pentachlorophenol in an aqueous extract","Pâtes, papier et carton — Détermination du pentachlorophénol dans un extrait aqueux",2003-12-09,1,"['85.060','85.040']",ISO/TC 6,9599,,[43635],"['en','fr']",8,"<p>ISO 15320:2004 specifies a test method for the determination of pentachlorophenol (PCP) in an aqueous extract in pulp, paper and board. Though it is developed for paper and board intended to come into contact with foodstuffs, it is applicable to all kinds of pulp, paper and board.</p>"

27522,IS,,ISO 15349-2:1999,Unalloyed steel — Determination of low carbon content — Part 2: Infrared absorption method after combustion in an induction furnace (with preheating),Acier non allié — Détermination des faibles teneurs en carbone — Partie 2: Méthode par absorption dans l'infrarouge après combustion dans un four à induction (avec préchauffage),1999-12-16,1,['77.080.20'],ISO/TC 17/SC 1,9599,,[74713],"['en','fr']",14,"<p>This part of ISO 15349 specifies an infrared absorption method after combustion in an induction furnace for the</p><p>determination of the low carbon content in unalloyed steel.</p><p>The method is applicable to carbon contents between 0,000 3 % (<i>m</i>/<i>m</i>) an

29686,IS,,ISO 15360-2:2001,Recycled pulps — Estimation of Stickies and Plastics — Part 2: Image analysis method,Pâtes recyclées — Estimation des matières collantes et des matières plastiques — Partie 2: Méthode par analyse d'image,2001-11-15,1,['85.040'],ISO/TC 6,9599,,[62988],"['en','fr']",14,

45328,IS,Cor,ISO 15360-2:2001/Cor 1:2007,Recycled pulps — Estimation of Stickies and Plastics — Part 2: Image analysis method — Technical Corrigendum 1,Pâtes recyclées — Estimation des matières collantes et des matières plastiques — Partie 2: Méthode par analyse d'image — Rectificatif technique 1,2007-05-18,1,['85.040'],ISO/TC 6,9599,,[62988],"['en','fr']",2,

26920,IS,,ISO 15362:1998,Optics and optical instruments — Stereomicroscopes — Information provided to the user,Optique et instruments d'optique — Stéréo-microscopes — Informations délivrées à l'utilisateur,1998-07-02,1,['37.020'],ISO/TC 172/SC 5,9599,,[64985],"['en','fr']",4,

27032,IS,,ISO 15363:2000,Metallic materials — Tube ring hydraulic pressure test,Matériaux métalliques — Essai d'expansion hydraulique sur anneau tubulaire,2000-08-17,1,['77.040.10'],ISO/TC 164/SC 2,9599,,[72569],"['en','fr']",8,

27037,IS,,ISO 15364:2000,Ships and marine technology — Pressure/vacuum valves for cargo tanks,Navires et technologie maritime — Robinets à pression/à vide pour citernes de chargement,2000-08-31,1,['47.020.30'],ISO/TC 8/SC 3,9599,,[39826],['en'],13,

39826,IS,,ISO 15364:2007,Ships and marine technology — Pressure/vacuum valves for cargo tanks,Navires et technologie maritime — Robinets à pression/à vide pour citernes de chargement,2007-12-10,2,['47.020.30'],ISO/TC 8/SC 3,9599,[27037],[62241],['en'],23,"<p>ISO 15364:2007 applies to pressure-vacuum relief valves protecting marine vessel systems, including cargo tanks, which may be subject to gas/vapour pressure or vacuum beyond the design parameters of the system/tank. </p><p>ISO 15364:2007 specifies the minimum requirements for performance and testing of pressure-vacuum relief valves, with emphasis on selection of materials, internal finish and surface requirements for pressure-vacuum valv

62241,IS,,ISO 15364:2016,Ships and marine technology — Pressure/vacuum valves for cargo tanks,Navires et technologie maritime — Soupapes de pression/dépression pour citernes à cargaison,2016-04-15,3,['47.020.30'],ISO/TC 8/SC 3,9599,[39826],[74708],['en'],27,"<p>ISO 15364:2016 is applicable to pressure-vacuum relief valves protecting marine vessel systems, including cargo tanks, which may be subject to gas/vapour pressure or vacuum beyond the design parameters of the system/tank. This International Standard specifies the minimum requirements for performance and testing of pressure-vacuum relief valves, with emphasis on selection of materials, internal finish and surface requirements for press

26210,IS,,ISO 15366:1999,Nuclear energy — Chemical separation and purification of uranium and plutonium in nitric acid solutions for isotopic and dilution analysis by solvent chromatography,Énergie nucléaire — Séparation et purification chimique de l'uranium et du plutonium dans les solutions d'acide nitrique par extraction chromatographique par solvant pour les mesures isotopiques et les analyses par dilution isotopiques,1999-10-21,1,['27.120.30'],ISO/TC 85/SC 5,9599,,"[56505,40924,56506]","['en','fr']",11,

26583,IS,,ISO 15368:2001,Optics and optical instruments — Measurement of reflectance of plane surfaces and transmittance of plane parallel elements,Optique et instruments d'optique — Méthode de mesurage de la réflectance des surfaces planes et de la transmittance des éléments à plan parallèle,2001-08-23,1,['17.180.01'],ISO/TC 172/SC 1,9599,,[72598],"['en','fr']",13,<p/>

27029,IS,,ISO 15370:2001,Ships and marine technology — Low-location lighting on passenger ships — Arrangement,Navires et technologie maritime — Éclairage situé en bas sur les navires à passagers — Disposition,2001-04-19,1,['47.020.99'],ISO/TC 8/SC 1,9599,,[44457],['en'],17,

44457,IS,,ISO 15370:2010,Ships and marine technology — Low-location lighting (LLL) on passenger ships — Arrangement,Navires et technologie maritime — Éclairage situé en bas sur les navires à passagers — Disposition,2010-02-11,2,['47.020.99'],ISO/TC 8/SC 1,9599,[27029],[71938],"['en','ru']",30,"<p>ISO 15370:2010 specifies the requirements for the approval, installation and maintenance of low-location lighting systems as defined in Chapter II-2, Regulation 13.3.2.5.1 of the <i>International Convention for the Safety of Life at Sea, </i>1974 (SOLAS 1974), as amended in 2000 and the IMO <i>International Code for Fire Safety Systems</i>.</p>"

27031,IS,,ISO 15371:2000,Ships and marine technology — Fire-extinguishing systems for protection of galley deep-fat cooking equipment — Fire tests,Navires et technologie maritime — Systèmes d'extinction des incendies de l'équipement de bacs de friture dans les cuisines — Essais d'incendies,2000-07-27,1,"['13.220.10','47.020.99']",ISO/TC 8/SC 1,9599,,[44456],['en'],5,

44456,IS,,ISO 15371:2009,Ships and marine technology — Fire-extinguishing systems for protection of galley cooking equipment,Navires et technologie maritime — Systèmes d'extinction d'incendie des équipements de cuisine,2009-03-11,2,"['13.220.10','47.020.99']",ISO/TC 8/SC 1,9599,[27031],[68559],['en'],25,"<p>ISO 15371:2009 applies to the design, testing, and operation of pre-engineered fire extinguishing systems to protect the galley hoods, ducts, fryers and other grease laden appliances. </p><p>Pre-engineered fire-extinguishing system units are also required to comply with requirements for the construction and components performance as applicable to specific types, designs, sizes and arrange

68559,IS,,ISO 15371:2015,Ships and marine technology — Fire-extinguishing systems for protection of galley cooking equipment,Navires et technologie maritime — Systèmes d'extinction d'incendie des équipements de cuisine,2015-11-16,3,"['13.220.10','47.020.99']",ISO/TC 8/SC 1,9599,[44456],[83098],['en'],27,"<p>ISO 15371:2015 applies to the design, testing, and operation of pre-engineered fire extinguishing systems to protect the galley hoods, ducts, fryers and other grease-laden appliances.</p><p>Pre-engineered fire-extinguishing system units are also required to comply with requirements for the construction and components performance as applicable to specific types, designs, sizes and arrangem

26930,IS,,ISO 15373:2001,Plastics — Polymer dispersions — Determination of free formaldehyde,Plastiques — Dispersions de polymères — Dosage du formaldéhyde libre,2001-08-30,1,['83.080.20'],ISO/TC 61/SC 9,9599,,"[83774,88258]","['en','fr']",12,"<p>This International Standard describes two methods for the determination of free formaldehyde (HCHO) in polymer</p><p>dispersions. The procedure has been evaluated using acrylic, acrylonitrile butadiene, carboxylated styrenebutadiene</p><p>and vinyl acetate polymer dispersions. Both test methods may also be applicable to polymer dispersions</p><p>of other compositions.</p><p>Method A is the preferred method for polymer dispersions with a free-formald

26838,IS,,ISO 15374:1998,Implants for surgery — Requirements for production of forgings,Implants chirurgicaux — Exigences pour la fabrication des pièces forgées,1998-08-13,1,['11.040.40'],ISO/TC 150/SC 1,9599,,"[88633,82120]",['en'],4,

37521,IS,,ISO 15375:2004,Hanging devices for multiple use with infusion bottles — Requirements and test methods,Dispositifs de suspension à usage multiple pour flacons de transfusion et de perfusion — Exigences et méthodes d'essai,2004-11-23,1,['11.040.20'],ISO/TC 76,9599,,[52805],['en'],3,"<p>ISO 15375:2004 specifies requirements for permanent hanging devices, fixed to infusion racks or set-up devices, for infusion bottles that conform to the requirements of ISO 8536-1. The hanging devices are intended for multiple use.</p><p>The purpose of ISO 15375:2004 is to establish a safe hanging device for infusion bottles during administering of their contents.</p>"

37522,IS,,ISO 15378:2006,"Primary packaging materials for medicinal products — Particular requirements for the application of ISO 9001:2000, with reference to Good Manufacturing Practice (GMP)",Matériaux d'emballage primaire pour médicaments — Exigences particulières pour l'application de l'ISO 9001:2000 prenant en considération les Bonnes Pratiques de Fabrication (BPF),2006-03-01,1,"['03.100.70','11.040.01']",ISO/TC 76,9599,,[54973],"['en','fr','ru']",59,"<p>ISO 15378:2006 specifies requirements for a quality management system where an organization needs to demonstrate its ability to provide primary packaging materials for medicinal products, which consistently meet customer requirements, i

54973,IS,,ISO 15378:2011,"Primary packaging materials for medicinal products — Particular requirements for the application of ISO 9001:2008, with reference to Good Manufacturing Practice (GMP)",Articles de conditionnement primaire pour médicaments — Exigences particulières pour l'application de l'ISO 9001:2008 prenant en considération les Bonnes Pratiques de Fabrication (BPF),2011-10-25,2,"['03.100.70','11.040.01']",ISO/TC 76,9599,[37522],[64289],"['en','fr']",67,"<p>ISO 15378:2011 specifies requirements for a quality management system where an organization needs to demonstrate its ability to provide primary packaging materials for medicinal products, which consistently meet customer require

64289,IS,,ISO 15378:2015,"Primary packaging materials for medicinal products — Particular requirements for the application of ISO 9001:2008, with reference to Good Manufacturing Practice (GMP)",Articles d'emballage primaire pour médicaments — Exigences particulières pour l'application de l'ISO 9001:2008 prenant en considération les Bonnes Pratiques de Fabrication (BPF),2015-10-06,3,"['03.100.70','11.040.01']",ISO/TC 76,9599,[54973],[70729],"['en','fr']",63,"<p><i>ISO 15378:2015 specifies requirements for a quality management system where an organization needs to demonstrate its ability to provide primary packaging materials for medicinal products, which consistently meet customer requirement

27450,IS,,ISO 15379-1:2004,Carbonaceous materials for the production of aluminium — Cathode block materials — Part 1: Determination of the expansion due to sodium penetration with application of pressure,Produits carbonés utilisés pour la production de l'aluminium — Blocs cathodiques — Partie 1: Détermination de l'expansion due à la pénétration du sodium avec application de pression,2004-06-16,1,['71.100.10'],ISO/TC 226,9599,,[66678],['en'],5,<p>ISO 15379-1:2004 provides a method for the determination of the linear expansion of cathode-block materials used in the production of aluminium under external pressure due to sodium penetration.</p><p>The linear expansion of the blocks depends on the

66678,IS,,ISO 15379-1:2015,Carbonaceous materials for the production of aluminium — Cathode block materials — Part 1: Determination of the expansion due to sodium penetration with application of pressure,Produits carbonés utilisés pour la production de l'aluminium — Blocs cathodiques — Partie 1: Détermination de l'expansion due à la pénétration du sodium avec application de pression,2015-05-22,2,['71.100.10'],ISO/TC 226,9599,[27450],[73943],['en'],6,<p>ISO 15379-1:2015 specifies a method that covers the determination of linear expansion under external pressure due to sodium penetration in cathode-block materials used in the production of aluminium.</p><p>The linear expansion of the blocks de

36725,IS,,ISO 15379-2:2004,Carbonaceous materials for the production of aluminium — Cathode block materials — Part 2: Determination of the expansion due to sodium penetration without application of pressure,Produits carbonés utilisés pour la production de l'aluminium — Blocs cathodiques — Partie 2: Détermination de l'expansion due à la pénétration du sodium sans application de pression,2004-06-16,1,['71.100.10'],ISO/TC 226,9599,,[66677],['en'],6,<p>ISO 15379-2:2004 provides a method for the determination of the linear expansion of cathode block materials used in the production of aluminium due to sodium penetration.</p><p>The linear expansion of the blocks depends on the sampling direction d

27483,IS,,ISO 15380:2002,"Lubricants, industrial oils and related products (class L) — Family H (Hydraulic systems) — Specifications for categories HETG, HEPG, HEES and HEPR","Lubrifiants, huiles industrielles et produits connexes (classe L) — Famille H (Systèmes hydrauliques) — Spécifications pour les catégories HETG, HEPG, HEES et HEPR",2002-03-07,1,['75.100'],ISO/TC 28/SC 4,9599,,[54991],"['en','fr']",19,"<p>This International Standard specifies the requirements for environmentally acceptable hydraulic fluids and is intended for hydraulic systems, particularly hydraulic fluid power systems. The purpose of this International Standard is to provide guidance for suppliers and users of enviro

54991,IS,,ISO 15380:2011,"Lubricants, industrial oils and related products (class L) — Family H (Hydraulic systems) — Specifications for categories HETG, HEPG, HEES and HEPR","Lubrifiants, huiles industrielles et produits connexes (classe L) — Famille H (Systèmes hydrauliques) — Spécifications applicables aux catégories HETG, HEPG, HEES et HEPR",2011-03-29,2,['75.100'],ISO/TC 28/SC 4,9599,[27483],[66277],"['en','fr']",18,"<p>ISO 15380:2011 specifies the requirements for environmentally acceptable hydraulic fluids. It is applicable to hydraulic systems, particularly hydraulic fluid power systems. The purpose of this International Standard is to provide guidance for suppliers and users of envi

66277,IS,,ISO 15380:2016,"Lubricants, industrial oils and related products (class L) — Family H (Hydraulic systems) — Specifications for hydraulic fluids in categories HETG, HEPG, HEES and HEPR","Lubrifiants, huiles industrielles et produits connexes (classe L) — Famille H (Systèmes hydrauliques) — Spécifications applicables aux fluides hydrauliques des catégories HETG, HEPG, HEES et HEPR",2016-11-21,3,['75.100'],ISO/TC 28/SC 4,9599,[54991],[82967],"['en','fr']",19,"<p>ISO 15380:2016 specifies the requirements for environmentally acceptable hydraulic fluids and is intended for hydraulic systems, particularly hydraulic fluid power systems. The purpose of this International Standard is to prov

27496,IS,,ISO 15382:2002,"Nuclear energy — Radiationprotection — Procedure for radiation protection monitoring in nuclear installations for external exposure to weakly penetrating radiation, especially to beta radiation","Énergie nucléaire — Radioprotection — Procédure de surveillance dosimétrique de radioprotection dans les installations nucléaires pour l'exposition externe aux rayonnements faiblement pénétrants, en particulier au rayonnement bêta",2002-05-02,1,['13.280'],ISO/TC 85/SC 2,9599,,[61582],"['en','fr']",24,"<p>This International Standard specifies a procedure for radiation protection monitoring in nuclear installations for external exposure to weakly penetrating radiation, especi

61582,IS,,ISO 15382:2015,"Radiological protection — Procedures for monitoring the dose to the lens of the eye, the skin and the extremities","Radioprotection — Procédures pour la surveillance des doses au cristallin, à la peau et aux extrémités",2015-11-19,2,['13.280'],ISO/TC 85/SC 2,9599,[27496],[84052],"['en','fr']",27,"<p>ISO 15382:2015 provides procedures for monitoring the dose to the skin, the extremities, and the lens of the eye. It gives guidance on how to decide if such dosemeters are needed and to ensure that individual monitoring is appropriate to the nature of the exposure, taking practical considerations into account. National regulations, if they exist, provide requirements tha

26960,IS,,ISO 15383:2001,Protective gloves for firefighters — Laboratory test methods and performance requirements,Gants de protection pour sapeurs-pompiers — Méthodes d'essai en laboratoire et exigences de performance,2001-09-20,1,"['13.340.10','13.340.40']",ISO/TC 94/SC 14,9599,,[85709],"['en','fr']",22,"<p>This International Standard specifies test methods and minimum requirements for protective gloves to be worn</p><p>during fire fighting and associated activities where there is a risk of heat and/or flame.</p><p>The purpose of this International Standard is to provide minimum performance requirements for protective gloves</p><p>designed to protect against injury in fire fighting operati

26961,IS,,ISO 15384:2003,Protective clothing for firefighters — Laboratory test methods and performance requirements for wildland firefighting clothing,Vêtements de protection pour sapeurs-pompiers — Méthodes d'essai en laboratoire et exigences de performance pour vêtements portés pendant la lutte contre les feux d'espaces naturels,2003-04-02,1,['13.340.10'],ISO/TC 94/SC 14,9599,,[67219],"['en','fr']",10,"<p>ISO 15384:2003 specifies methods of test and minimum performance requirements for protective clothing to be worn in wildland firefighting and associated activities. This clothing is not intended to provide protection during fire entrapment. ISO 15384:2003 applies to the general design of

40262,IS,,ISO 15388:2004,Space systems — Contamination and cleanliness control,Systèmes spatiaux — Contrôle de la contamination et de la propreté,2004-09-07,1,['49.140'],ISO/TC 20/SC 14,9599,,[57326],"['en','fr']",19,"<p>ISO 15388:2004 establishes general requirements for contamination and cleanliness control to be applied, at all tiers of supply, to the development of space systems including ground processing facilities, ground support equipment, launch vehicles, spacecraft, payloads, and ground processing and on-orbit operations. It also provides guidelines for the establishment of a contamination and cleanliness control programme.</p>"

57326,IS,,ISO 15388:2012,Space systems — Contamination and cleanliness control,Systèmes spatiaux — Contrôle de la contamination et de la propreté,2012-02-14,2,['49.140'],ISO/TC 20/SC 14,9599,[40262],[76558],['en'],20,"<p>This International Standard establishes general requirements for contamination and cleanliness control that are applicable, at all tiers of supply, to the development of space systems, including ground processing facilities, ground support equipment, launch vehicles, spacecraft, payloads, and ground processing and on-orbit operations. It also provides guidelines for the establishment of a contamination and cleanliness control programme.</p>"

27528,IS,,ISO 15389:2001,Space systems — Flight-to-ground umbilicals,Systèmes spatiaux — Ombilicaux bord-sol,2001-01-18,1,['49.140'],ISO/TC 20/SC 14,9599,,[85528],"['en','fr']",11,"<p>This International Standard defines the general criteria for the development of flight-to-ground umbilical systems</p><p>used by a space system. The criteria specified herein is limited to the service arms or equivalent mechanisms,</p><p>umbilical carriers and plates, couplings, connectors, withdrawal and retract devices, handling mechanisms and</p><p>control systems for mechanisms.</p>"

37210,IS,Amd,ISO 15389:2001/Amd 1:2005,Space systems — Flight-to-ground umbilicals — Amendment 1: Prevention of accidental cross-connection,Systèmes spatiaux — Ombilicaux bord-sol — Amendement 1: Prévention des croisements accidentels de connexions,2005-09-28,1,['49.140'],ISO/TC 20/SC 14,9599,,[85528],"['en','fr']",6,

43878,IS,Cor,ISO 15389:2001/Cor 1:2006,Space systems — Flight-to-ground umbilicals — Technical Corrigendum 1,Systèmes spatiaux — Ombilicaux bord-sol — Rectificatif technique 1,2006-02-15,1,['49.140'],ISO/TC 20/SC 14,9599,,[85528],"['en','fr']",1,

6127,IS,,ISO 1539:1980,Programming languages — FORTRAN,Langages de programmation — FORTRAN,1980-03-01,1,['35.060'],ISO/IEC JTC 1,9599,,[6128],"['en','fr']",1,

40432,IS,,ISO 15392:2008,Sustainability in building construction — General principles,Développement durable dans la construction — Principes généraux,2008-04-22,1,['91.040.01'],ISO/TC 59/SC 17,9599,,[69947],"['en','fr','ru']",20,"<p>ISO 15392:2008 identifies and establishes general principles for sustainability in building construction. It is based on the concept of sustainable development as it applies to the life cycle of buildings and other construction works, from their inception to the end of life.</p><p>ISO 15392:2008 is applicable to buildings and other construction works individually and collectively, as well as to the materials, products, services and processes related to the life

23870,IS,,ISO 15394:2000,"Packaging — Bar code and two-dimensional symbols for shipping, transport and receiving labels","Emballage — Codes à barres et symboles bidimensionnels pour l'expédition, le transport et les étiquettes de réception",2000-04-13,1,"['55.020','35.040.50']",ISO/TC 122,9599,,[44030],['en'],46,

44030,IS,,ISO 15394:2009,"Packaging — Bar code and two-dimensional symbols for shipping, transport and receiving labels","Emballage — Codes à barres et symboles bidimensionnels pour l'expédition, le transport et les étiquettes de réception",2009-04-14,2,"['55.020','35.040.50']",ISO/TC 122,9599,[23870],[65013],['en'],55,"<p>ISO 15394:2009</p><ul><li>specifies the minimum requirements for the design of labels containing linear bar code and two‑dimensional symbols on transport units to convey data between trading partners;</li><li>provides for traceability of transported units via a unique transport unit identifier (licence plate);</li><li>provides guidance on the formatting on the label of dat

27535,IS,,ISO 15396:1998,Space data and information transfer systems — Cross support reference model — Space link extension services,Systèmes de transfert des informations et données spatiales — Modèle de référence pour le support croisé — Service S.L.E.,1998-04-30,1,['49.140'],ISO/TC 20/SC 13,9599,,[43828],"['en','fr']",93,

6130,IS,,ISO 1540:1977,Aerospace — Characteristics of aircraft electrical systems,Aéronautique — Caractéristiques des réseaux électriques à bord des aéronefs,1977-12-01,1,['49.060'],ISO/TC 20,9599,,[6131],"['en','fr']",19,

6131,IS,,ISO 1540:1984,Aerospace — Characteristics of aircraft electrical systems,Aéronautique — Caractéristiques des réseaux électriques à bord des aéronefs,1984-11-01,2,['49.060'],ISO/TC 20/SC 1,9599,"[4094,6130]","[37584,42067]","['en','fr']",19,<p>Specifies the characteristics of electrical power supplied to the terminals of airborne equipment and defines limits for those aspects of utilization equipment which may adversely affect the characteristics of electrical power supplied to other equipment. Its purposes to achieve compatibility between airborne utilization equipment and aircraft electrical power supplies. Ground support electrical power supplies forms the subject of a separate In

27082,IS,,ISO 15403:2000,Natural gas — Designation of the quality of natural gas for use as a compressed fuel for vehicles,Gaz naturel — Désignation de la qualité de gaz naturel pour usage comme carburant comprimé pour véhicules,2000-06-08,1,['75.060'],ISO/TC 193,9599,,[44211],"['en','fr']",23,

40701,IS,,ISO 15439-1:2007,"Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) — Polyamide (PA) — Part 1: General","Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux pour une pression maximale de service inférieure ou égale à 0,4 MPa (4 bar) — Polyamide (PA) — Partie 1: Généralités",2007-12-06,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 4,9599,,[59855],"['en','ru']",22,"<p>ISO 15439-1:2007 specifies the general properties of polyamide (PA) compounds for the manufacturing of pipes, fittings and valves made from such compounds, intended to be buried and used for the supply of gase

40702,IS,,ISO 15439-2:2007,"Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) — Polyamide (PA) — Part 2: Pipes","Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux pour une pression maximale de service inférieure ou égale à 0,4 MPa (4 bar) — Polyamide (PA) — Partie 2: Tuyauteries",2007-12-06,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 4,9599,,[59856],"['en','ru']",7,"<p>ISO 15439-2:2007 specifies the physical and mechanical properties of pipes made from polyamide in accordance with ISO 15493-1, intended to be buried and used for the supply of gaseous fuels for maximum operating

40703,IS,,ISO 15439-3:2007,"Plastics piping systems for the supply of gaseous fuels for maximum operating pressure up to and including 0,4 MPa (4 bar) — Polyamide (PA) — Part 3: Fittings","Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux pour une pression maximale de service inférieure ou égale à 0,4 MPa (4 bar) — Polyamide (PA) — Partie 3: Raccords",2007-12-06,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 4,9599,,[59857],"['en','ru']",6,"<p>ISO 15439-3:2007 specifies the physical and mechanical characteristics of fittings made from polyamide in accordance with ISO 15439-1, intended to be buried and used for the supply of gaseous fuels for maximum op

37530,IS,,ISO 15442:2005,Cranes — Safety requirements for loader cranes,Appareils de levage à charge suspendue — Exigences de sécurité pour les grues de chargement,2005-10-27,1,['53.020.20'],ISO/TC 96/SC 6,9599,,"[50573,57221]","['en','fr']",64,"<p>ISO 15442:2005 specifies minimum requirements for design, calculation, examinations and tests of hydraulic powered loader cranes and their mountings on to vehicles or static foundations. It applies to all new loader cranes manufactured one year after its publication. It is not the intent of this International Standard to require the retrofitting of existing loader cranes.</p><p>ISO 15442:2005 does not apply to loader cranes used on board ships or

27765,IS,,ISO 15469:1997,Spatial distribution of daylight — CIE standard overcast sky and clear sky,Répartition spatiale de la lumière du jour — Ciel couvert et ciel serein normalisés CIE,1997-12-19,1,['17.180.20'],CIE,9599,,[38608],"['en','fr']",4,

27191,IS,,ISO 15470:2004,Surface chemical analysis — X-ray photoelectron spectroscopy — Description of selected instrumental performance parameters,Analyse chimique des surfaces — Spectroscopie de photoélectrons X — Description de certains paramètres relatifs à la performance instrumentale,2004-05-03,1,['71.040.40'],ISO/TC 201/SC 7,9599,,[71922],['en'],4,<p>ISO 15470:2004 describes the way in which specific aspects of the performance of an X-ray photoelectron spectrometer shall be described.</p>

27192,IS,,ISO 15471:2004,Surface chemical analysis — Auger electron spectroscopy — Description of selected instrumental performance parameters,Analyse chimique des surfaces — Spectroscopie d'électrons Auger — Description de certains paramètres relatifs à la performance instrumentale,2004-05-04,1,['71.040.40'],ISO/TC 201/SC 7,9599,,[71085],['en'],5,<p>ISO 15471:2004 describes the way in which specific aspects of the performance of an Auger electron spectrometer shall be described.</p>

27190,IS,,ISO 15472:2001,Surface chemical analysis — X-ray photoelectron spectrometers — Calibration of energy scales,Analyse chimique des surfaces — Spectromètres de photoélectrons X — Étalonnage en énergie,2001-02-08,1,['71.040.40'],ISO/TC 201/SC 7,9599,,[55796],"['en','fr']",27,

27840,IS,,ISO 15480:1999,Hexagon washer head drilling screws with tapping screw thread,"Vis autoperceuses à tête hexagonale à ambase plate, avec filetage de vis à tôle",1999-09-08,1,['21.060.10'],ISO/TC 2/SC 13,9599,,[73633],"['en','fr']",5,

27411,IS,,ISO 15487:1999,Textiles — Method for assessing appearance of apparel and other textile end products after domestic washing and drying,Textiles — Méthode d'évaluation de l'aspect des vêtements et autres produits finis textiles après lavage et séchage domestiques,1999-12-16,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[52638],"['en','fr']",10,

52638,IS,,ISO 15487:2009,Textiles — Method for assessing appearance of apparel and other textile end products after domestic washing and drying,Textiles — Méthode d'évaluation de l'aspect des vêtements et autres produits finis textiles après lavage et séchage domestiques,2009-04-29,2,['59.080.01'],ISO/TC 38/SC 2,9599,"[46324,27411]",[67602],"['en','fr']",12,"<p>ISO 15487:2009 specifies a method of test for evaluating the smoothness appearance of flat fabric and seams, and the retention of pressed-in creases in garments and other textile products after one or several domestic washing and drying treatments. It is applicable to any washable textile end product of any fabric construction. Techni

25443,IS,,ISO 15488:1996,"Collets with 8 degree setting angle for tool shanks — Collets, nuts and fitting dimensions","Pinces de serrage avec angle de réglage de 8 degrés pour queues d'outil — Pinces, écrous de serrage et dimensions d'assemblage",1996-12-26,1,['25.060.20'],ISO/TC 29,9599,,[36756],"['en','fr']",11,"<p>Specifies the dimensions, materials and manufacturing requirements, and designation of collets for tools with parallel shanks and their corresponding holders and nuts. Form A applies to milling and any other application where a hard collet bore is required. Form B applies for general purposes.</p>"

31908,IS,,ISO 15489-1:2001,Information and documentation — Records management — Part 1: General,Information et documentation — «Records management» — Partie 1: Principes directeurs,2001-09-28,1,['01.140.20'],ISO/TC 46/SC 11,9599,"[27899,27896,27900,27897,27901,27898]","[41633,62542]","['en','fr']",19,

26544,IS,,ISO 15490:2000,"Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for tensile strength of monolithic ceramics at room temperature",Céramiques techniques — Méthode d'essai de résistance à la traction des céramiques monolithiques à température ambiante,2000-06-29,1,['81.060.30'],ISO/TC 206,9599,,[43927],"['en','fr']",10,

27910,IS,,ISO 15494:2003,"Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE) and polypropylene (PP) — Specifications for components and the system — Metric series","Systèmes de canalisations en matières plastiques pour les applications industrielles — Polybutène (PB), polyéthylène (PE) et polypropylène (PP) — Spécifications pour les composants et le système — Série métrique",2003-04-14,1,['23.040.01'],ISO/TC 138/SC 3,9599,,"[59990,55627]","['en','fr']",89,"<p>ISO 15494:2003 specifies the characteristics and requirements for components such as pipes, fittings and valves made from one of the following materials:</p><ol><li>polybutene (PB);</li><li>polyethy

27920,IS,,ISO 15496:2004,Textiles — Measurement of water vapour permeability of textiles for the purpose of quality control,Textiles — Mesurage de la perméabilité à la vapeur d'eau des textiles dans le but du contrôle qualité,2004-04-28,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[65150],"['en','fr']",12,"<p>ISO 15496:2004 describes a comparatively simple method for testing the water vapour permeability of textiles that will provide the manufacturer with a clearly recognized method for quality control within the plant. It is not applicable for classifying the water vapour resistance of textiles against values relating to physiological effects specified in product standards, and particularly not tho

43763,IS,Cor,ISO 15496:2004/Cor 1:2006,Textiles — Measurement of water vapour permeability of textiles for the purpose of quality control — Technical Corrigendum 1,Textiles — Mesurage de la perméabilité à la vapeur d'eau des textiles dans le but du contrôle qualité — Rectificatif technique 1,2006-01-31,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[65150],"['en','fr']",1,

3984,IS,,ISO 155:1975,Transmission pulleys — Limiting values for adjustment of centres,Poulies de transmission — Limites de réglage d'entraxe,1975-05-01,1,['21.220.10'],ISO/TC 41,9599,,[3985],"['en','fr']",1,

3985,IS,,ISO 155:1989,Belt drives — Pulleys — Limiting values for adjustment of centres,Transmissions par courroies — Poulies — Limites de réglage d'entraxe,1989-08-17,2,['21.220.10'],ISO/TC 41/SC 1,9599,[3984],[25449],"['en','fr']",4,

25449,IS,,ISO 155:1998,Belt drives — Pulleys — Limiting values for adjustment of centres,Transmissions par courroies — Poulies — Limites de réglage d'entraxe,1998-07-16,3,['21.220.10'],ISO/TC 41/SC 1,9599,[3985],[70613],"['en','fr']",6,

29020,IS,,ISO 15500-1:2000,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 1: General requirements and definitions,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 1: Exigences générales et définitions,2000-03-02,1,['43.060.40'],ISO/TC 22/SC 41,9599,,[60255],['en'],5,

36082,IS,Amd,ISO 15500-1:2000/Amd 1:2003,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 1: General requirements and definitions — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 1: Exigences générales et définitions — Amendement 1,2003-05-05,1,['43.060.40'],ISO/TC 22/SC 41,9599,,[60255],['en'],1,

30458,IS,,ISO 15500-10:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 10: Gas-flow adjuster,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 10: Régulateur du débit de gaz,2001-01-18,1,['43.060.40'],ISO/TC 22/SC 41,9599,,[60284],['en'],4,

30459,IS,,ISO 15500-11:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 11: Gas/air mixer,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 11: Mélangeur air/gaz,2001-01-18,1,['43.060.40'],ISO/TC 22/SC 41,9599,,[60285],['en'],3,

30460,IS,,ISO 15500-12:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 12: Pressure relief valve (PRV),Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 12: Soupapes de sécurité à la pression,2001-01-18,1,['43.060.40'],ISO/TC 22/SC 41,9599,,[60286],['en'],4,

30461,IS,,ISO 15500-13:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 13: Pressure relief device (PRD),Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 13: Dispositifs de limitation de pression,2001-04-19,1,['43.060.40'],ISO/TC 22,9599,,[55424],['en'],11,

55424,IS,,ISO 15500-13:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 13: Pressure relief device (PRD),Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 13: Dispositifs de limitation de pression,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[30461],[75992],['en'],11,"<p>This part of ISO 15500 specifies tests and requirements for the pressure relief device (PRD), a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833.</p><p>This part of ISO 15500 is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordanc

67827,IS,Amd,ISO 15500-13:2012/Amd 1:2016,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 13: Pressure relief device (PRD) — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 13: Dispositifs de limitation de pression — Amendement 1,2016-03-23,2,['43.060.40'],ISO/TC 22/SC 41,9599,,[75992],['en'],1,

30462,IS,,ISO 15500-14:2002,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 14: Excess flow valve,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 14: Valve de limitation de débit,2002-03-28,1,['43.060.40'],ISO/TC 22,9599,,[51560],['en'],4,

51560,IS,,ISO 15500-14:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 14: Excess flow valve,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 14: Valve de limitation de débit,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[30462],[75993],['en'],5,"<p>This part of ISO 15500 specifies tests and requirements for the excess flow valve, a compressed natural gas</p><p>(CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833.</p><p>This part of ISO 15500 is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas</p><p>in accordance with ISO 15403.</p

67828,IS,Amd,ISO 15500-14:2012/Amd 1:2016,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 14: Excess flow valve — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 14: Valve de limitation de débit — Amendement 1,2016-03-23,2,['43.060.40'],ISO/TC 22/SC 41,9599,,[75993],['en'],1,

30463,IS,,ISO 15500-15:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 15: Gas-tight housing and ventilation hose,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 15: Compartiment étanche pour gaz et tuyaux de ventilation,2001-01-18,1,['43.060.40'],ISO/TC 22/SC 41,9599,,"[67708,60287]",['en'],3,

30464,IS,,ISO 15500-16:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 16: Rigid fuel line,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 16: Tuyauterie rigide pour combustible,2001-01-18,1,['43.060.40'],ISO/TC 22,9599,,[51559],['en'],4,

51559,IS,,ISO 15500-16:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 16: Rigid fuel line in stainless steel,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 16: Tuyauterie rigide pour combustible en acier inoxydable,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[30464],[75994],['en'],4,"<p>This part of ISO 15500 specifies tests and requirements for the rigid fuel line in stainless steel, a compressed</p><p>natural gas (CNG) fuel system component in accordance with ISO 1127 intended for use on the types of motor</p><p>vehicles defined in ISO 3833.</p><p>This part of ISO 15500 is applicable to vehicles (mono-fue

67829,IS,Amd,ISO 15500-16:2012/Amd 1:2016,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 16: Rigid fuel line in stainless steel — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 16: Tuyauterie rigide pour combustible en acier inoxydable — Amendement 1,2016-03-23,2,['43.060.40'],ISO/TC 22/SC 41,9599,,[75994],['en'],1,

30465,IS,,ISO 15500-17:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 17: Flexible fuel line,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 17: Tuyauterie flexible pour combustible,2001-01-18,1,['43.060.40'],ISO/TC 22,9599,,[51558],['en'],6,

51558,IS,,ISO 15500-17:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 17: Flexible fuel line,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 17: Tuyauterie flexible pour combustible,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[30465],[75995],['en'],5,"<p>This part of ISO 15500 specifies tests and requirements for the flexible fuel line, a compressed natural gas</p><p>(CNG) fuel system component in accordance with SAE J517 (100R8 hose) or JIS B 8362 intended for use on</p><p>the types of motor vehicles defined in ISO 3833.</p><p>This part of ISO 15500 is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel

67830,IS,Amd,ISO 15500-17:2012/Amd 1:2016,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 17: Flexible fuel line — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 17: Tuyauterie flexible pour combustible — Amendement 1,2016-03-23,2,['43.060.40'],ISO/TC 22/SC 41,9599,,[75995],['en'],1,

30466,IS,,ISO 15500-18:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 18: Filter,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 18: Filtre,2001-01-18,1,['43.060.40'],ISO/TC 22,9599,,[51557],['en'],3,

51557,IS,,ISO 15500-18:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 18: Filter,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 18: Filtre,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[30466],[75996],['en'],4,"<p>This part of ISO 15500 specifies tests and requirements for the filter, a compressed natural gas (CNG) fuel</p><p>system component intended for use on the types of motor vehicles defined in ISO 3833.</p><p>This part of ISO 15500 is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas</p><p>in accordance with ISO 15403. It is not applicable to the following:</p><p>a

67831,IS,Amd,ISO 15500-18:2012/Amd 1:2016,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 18: Filter — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 18: Filtre — Amendement 1,2016-03-23,2,['43.060.40'],ISO/TC 22/SC 41,9599,,[75996],['en'],1,

30467,IS,,ISO 15500-19:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 19: Fittings,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 19: Raccords,2001-01-18,1,['43.060.40'],ISO/TC 22,9599,,[51556],['en'],4,

51556,IS,,ISO 15500-19:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 19: Fittings,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 19: Raccords,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[30467],[75997],['en'],4,"<p>This part of ISO 15500 specifies tests and requirements for fittings, compressed natural gas (CNG) fuel system</p><p>components intended for use on the types of motor vehicles defined in ISO 3833.</p><p>This part of ISO 15500 is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas</p><p>in accordance with ISO 15403. It is not applicable to the following:</p><p>

67832,IS,Amd,ISO 15500-19:2012/Amd 1:2016,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 19: Fittings — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 19: Raccords — Amendement 1,2016-03-23,2,['43.060.40'],ISO/TC 22/SC 41,9599,,[75997],['en'],1,

29128,IS,,ISO 15500-2:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 2: Performance and general test methods,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 2: Performances et méthodes d'essai générales,2001-02-22,1,['43.060.40'],ISO/TC 22,9599,,[55422],['en'],8,

55422,IS,,ISO 15500-2:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 2: Performance and general test methods,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 2: Performances et méthodes d'essai générales,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[29128],[69110],['en'],8,

37854,IS,,ISO 15500-20:2007,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 20: Rigid fuel line in material other than stainless steel,Véhicules routiers — Composants des systèmes de remplissage en gaz naturel comprimé — Partie 20: Circuit de combustible rigide en matériaux autres que l'acier inoxydable,2007-03-09,1,['43.060.40'],ISO/TC 22/SC 41,9599,,[60259],['en'],4,"<p>ISO 15500-20:2007 provides specific requirements and tests applicable to the rigid fuel line in carbon steel, intended for use on the types of motor vehicles, as defined in ISO 3833, with a service pressure for natural gas as a fuel of 20 MPa (200 bar) settled at 15 °C.</p><p>ISO 15500 is intended

30450,IS,,ISO 15500-3:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 3: Check valve,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 3: Valve de contrôle,2001-01-18,1,['43.060.40'],ISO/TC 22,9599,,[51564],['en'],4,

51564,IS,,ISO 15500-3:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 3: Check valve,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 3: Valve de contrôle,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[30450],[75987],['en'],4,"<p>This part of ISO 15500 specifies tests and requirements for the check valve, a compressed natural gas (CNG)</p><p>fuel system component intended for use on the types of motor vehicles defined in ISO 3833.</p><p>This part of ISO 15500 is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas</p><p>in accordance with ISO 15403 (all parts). It is not applic

67822,IS,Amd,ISO 15500-3:2012/Amd 1:2016,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 3: Check valve — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 3: Valve de contrôle — Amendement 1,2016-03-23,2,['43.060.40'],ISO/TC 22/SC 41,9599,,[75987],['en'],1,

30451,IS,,ISO 15500-4:2001,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 4: Manual valve,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 4: Valve manuelle,2001-01-18,1,['43.060.40'],ISO/TC 22,9599,,[51563],['en'],4,

51563,IS,,ISO 15500-4:2012,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 4: Manual valve,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 4: Valve manuelle,2012-04-04,2,['43.060.40'],ISO/TC 22/SC 41,9599,[30451],[75988],['en'],5,"<p>ISO 15500-4:2012 specifies tests and requirements for the manual valve, a compressed natural gas (CNG) fuel system component intended for use on the types of motor vehicles defined in ISO 3833.</p><p>ISO 15500-4:2012 is applicable to vehicles (mono-fuel, bi-fuel or dual-fuel applications) using natural gas in accordance with ISO 15403.</p><p>It is not applicable to the following:</p><ol><

67823,IS,Amd,ISO 15500-4:2012/Amd 1:2016,Road vehicles — Compressed natural gas (CNG) fuel system components — Part 4: Manual valve — Amendment 1,Véhicules routiers — Composants des systèmes de combustible gaz naturel comprimé (GNC) — Partie 4: Valve manuelle — Amendement 1,2016-03-23,2,['43.060.40'],ISO/TC 22/SC 41,9599,,[75988],['en'],1,