Withdrawn and superseded ISO standards — page 38 of 246

22842,IS,,ISO 13761:1996,Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C,Tubes et raccords en matières plastiques — Facteurs de réduction de pression des canalisations en polyéthylène utilisées à des températures supérieures à 20 degrés C,1996-12-26,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 5,9599,,[63055],"['en','fr']",3,<p>Gives a method for the derivation of reduction factors to be used to obtain the maximum allowable operating pressure for elevated-temperature operation of polyethylene (PE) pipeline systems. Applicable to fluids which do not adversely affect the long-term properties of the polyethylen

22346,IS,,ISO 13766:1999,Earth-moving machinery — Electromagnetic compatibility,Engins de terrassement — Compatibilité électromagnétique,1999-05-06,1,"['33.100.01','53.100']",ISO/TC 127/SC 1,9599,,[38480],"['en','fr']",34,

38480,IS,,ISO 13766:2006,Earth-moving machinery — Electromagnetic compatibility,Engins de terrassement — Compatibilité électromagnétique,2006-05-15,2,"['33.100.01','53.100']",ISO/TC 127/SC 2,9599,[22346],"[67403,55663,67347,55664]","['en','fr']",36,<p>ISO 13766:2006 provides test methods and acceptance criteria for the evaluation of the electromagnetic compatibility of earth-moving machinery as defined in ISO 6165. The following electromagnetic phenomena are evaluated: broadband and narrowband electromagnetic interference; electromagnetic field immunity test; broadband and narrowband interference of electrical/electronic subassemblies; electromagnetic field immunity test of electrical/electr

54294,IS,,ISO 13767:2012,Ships and marine technology — Ship's mooring and towing fittings — Shipside roller fairleads,Navires et technologie maritime — Corps-morts et ferrures de remorquage de navires — Chaumards à rouleaux à quai,2012-06-25,1,['47.020.50'],ISO/TC 8/SC 4,9599,,[74610],['en'],8,"<p>This International Standard specifies the design, size and technical requirements for shipside roller fairleads installed to lead the mooring rope of a ship.</p>"

36362,IS,,ISO 13769:2002,Gas cylinders — Stamp marking,Bouteilles à gaz — Marquage,2002-06-20,1,['23.020.35'],ISO/TC 58/SC 4,9599,,[38950],"['en','fr']",11,"<p>ISO 13769 specifies stamp marking of refillable transportable gas cylinders and tubes of volume greater than 0,5 l and less than or equal to 3 000 l including:</p><ul><li>steel and aluminium gas cylinders;</li><li>composite gas cylinders;</li><li>acetylene cylinders.</li></ul><p>It is intended to be applied at the time of cylinder manufacture; however, it could be applied by the cylinder user during use operations, e.g., the stamping of <i>empty weight</i> on to cylinders not so marked at time of manufacture.</p><p>Stamp marking of LP

38705,IS,Amd,ISO 13769:2002/Amd 1:2003,Gas cylinders — Stamp marking — Amendment 1,Bouteilles à gaz — Marquage — Amendement 1,2003-11-19,1,['23.020.35'],ISO/TC 58/SC 4,9599,,[38950],"['en','fr']",1,

38950,IS,,ISO 13769:2007,Gas cylinders — Stamp marking,Bouteilles à gaz — Marquage,2007-11-29,2,['23.020.35'],ISO/TC 58/SC 4,9599,"[38705,36362]",[66185],"['en','fr']",13,"<p>ISO 13769:2007 specifies stamp marking of refillable transportable gas cylinders and tubes of volume greater than 0,5 l and less than or equal to 3 000 l, including:</p><ul><li>steel and aluminium gas cylinders;</li><li>composite gas cylinders;</li><li>acetylene cylinders;</li><li>LPG cylinders.</li></ul>"

21698,IS,,ISO 13772:1997,Forestry machinery — Portable chain-saws — Non-manually actuated chain brake performance,Matériel forestier — Scies à chaîne portatives — Performances du frein de chaîne automatique,1997-07-24,1,['65.060.80'],ISO/TC 23/SC 17,9599,[17112],"[38902,38007]","['en','fr']",8,

38902,IS,,ISO 13772:2004,Forestry machinery — Portable chain-saws — Non-manually actuated chain brake performance,Matériel forestier — Scies à chaîne portatives — Performance du frein de chaîne automatique,2004-10-01,2,['65.060.80'],ISO/TC 23/SC 17,9599,[21698],[46088],"['en','fr']",9,"<p>ISO 13772:2004 specifies the method of checking the function of the non-manually actuated chain brake on portable hand-held chain-saws used in forestry, and gives performance requirements. </p>"

46088,IS,,ISO 13772:2009,Forestry machinery — Portable chain-saws — Non-manually actuated chain brake performance,Matériel forestier — Scies à chaîne portatives — Performance du frein de chaîne automatique,2009-04-06,3,['65.060.80'],ISO/TC 23/SC 17,9599,[38902],[70254],"['en','fr']",9,<p>ISO 13772:2009 specifies a method for checking the functioning and performance of the non‑manually actuated chain brake on a portable hand-held chain-saw used for forest or tree service.</p>

22513,IS,,ISO 13775-1:2000,Thermoplastic tubing and hoses for automotive use — Part 1: Non-fuel applications,Tubes et tuyaux en thermoplastique pour l'industrie automobile — Partie 1: Applications sans carburant,2000-02-03,1,"['83.140.40','83.140.30','43.040.01']",ISO/TC 45/SC 1,9599,,"[65368,43707]",['en'],8,

65368,IS,,ISO 13775-1:2015,Thermoplastic tubing and hoses for automotive use — Part 1: Non-fuel applications,Tubes et tuyaux en thermoplastique pour l'industrie automobile — Partie 1: Applications sans carburant,2015-10-15,2,"['83.140.40','83.140.30','43.040.01']",ISO/TC 45/SC 1,9599,[22513],[81748],['en'],13,"<p>ISO 13775-1:2015 specifies the test requirements and the test methods for extruded thermoplastic tubing and hoses for use in vehicles powered by internal-combustion engines, excluding use in air braking systems (see ISO 7628), fuel lines (see ISO 13775‑2), and high-pressure hydraulic systems. This part of ISO 13775 is intended especially for use by original equipment manufacturers (

22514,IS,,ISO 13775-2:2000,Thermoplastic tubing and hoses for automotive use — Part 2: Petroleum-based-fuel applications,Tubes et tuyaux en thermoplastique pour l'industrie automobile — Partie 2: Applications pour carburants à base de pétrole,2000-02-03,1,"['43.060.40','83.140.40','83.140.30']",ISO/TC 45/SC 1,9599,,[43708],['en'],13,

54295,IS,,ISO 13776:2012,Ships and marine technology — Ship's mooring and towing fittings — Pedestal fairleads,Navires et technologie maritime — Corps-morts et ferrures de remorquage de navires — Chaumards à piédestal,2012-06-25,1,['47.020.50'],ISO/TC 8/SC 4,9599,,[74612],['en'],8,"<p>This International Standard specifies the design, size and technical requirements for pedestal fairleads installed to lead the mooring rope of a ship.</p>"

22908,IS,,ISO 13778:1999,Plain bearings — Quality assurance of thin-walled half bearings — Selective assembly of bearings to achieve a narrow clearance range,Paliers lisses - Assurances qualité des demi-coussinets minces - Assemblage sélectif des paliers pour obtenir un jeu faible,1999-09-30,1,['21.100.10'],ISO/TC 123/SC 5,9599,,[68626],"['en','fr']",7,

22465,IS,,ISO 13779-1:2000,Implants for surgery — Hydroxyapatite — Part 1: Ceramic hydroxyapatite,Implants chirurgicaux — Hydroxyapatite — Partie 1: Céramique à base d'hydroxyapatite,2000-08-17,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[43826],"['en','fr']",3,

26841,IS,,ISO 13779-2:2000,Implants for surgery — Hydroxyapatite — Part 2: Coatings of hydroxyapatite,Implants chirurgicaux — Hydroxyapatite — Partie 2: Revêtements à base d'hydroxyapatite,2000-08-17,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[43827],"['en','fr']",4,

43827,IS,,ISO 13779-2:2008,Implants for surgery — Hydroxyapatite — Part 2: Coatings of hydroxyapatite,Implants chirurgicaux — Hydroxyapatite — Partie 2: Revêtements à base d'hydroxyapatite,2008-09-17,2,['11.040.40'],ISO/TC 150/SC 1,9599,[26841],[64617],"['en','fr']",5,"<p>ISO 13779-2:2008 specifies requirements for ceramic hydroxyapatite coatings applied to metallic or non-metallic surgical implants.</p><p>ISO 13779-2:2008 does not cover coatings made from glasses, glass ceramics, alpha- and beta-calcium orthophosphate or other forms of calcium phosphate, nor does it cover coatings in which the hydroxyapatite is present in a powder form.</p>"

40828,IS,,ISO 13779-3:2008,Implants for surgery — Hydroxyapatite — Part 3: Chemical analysis and characterization of crystallinity and phase purity,Implants chirurgicaux — Hydroxyapatite — Partie 3: Analyse chimique et caractérisation de la cristallinité et de la pureté de phase,2008-01-31,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[64618],"['en','fr']",19,<p>ISO 13779-3:2008 specifies methods of test for the chemical analysis and assessment of crystallinity and phase composition of hydroxyapatite-based materials such as coatings and sintered products.</p>

30723,IS,,ISO 13779-4:2002,Implants for surgery — Hydroxyapatite — Part 4: Determination of coating adhesion strength,Implants chirurgicaux — Hydroxyapatite — Partie 4: Détermination de la résistance à l'adhésion du revêtement,2002-05-09,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[64619],"['en','fr']",7,<p>This part of ISO 13779 specifies test methods for measurement of the adhesion strength of hydroxyapatite coatings intended for use on components of surgical implants.</p>

22467,IS,,ISO 13781:1997,Poly(L-lactide) resins and fabricated forms for surgical implants — In vitro degradation testing,Résines et éléments à base de poly(L-lactide) pour implants chirurgicaux — Essais de dégradation in vitro,1997-01-22,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[64565],"['en','fr']",9,<p>Describes methods for the determination of chemical and mechanical changes in properties of poly(L-lactide) under in vitro degradation testing conditions.The poly L-lactid is used for the manufacture of surgical implants. The purpose is to compare and/or evaluate materials or processing conditions.</p>

22468,IS,,ISO 13782:1996,Implants for surgery — Metallic materials — Unalloyed tantalum for surgical implant applications,Implants chirurgicaux — Produits à base de métaux — Tantale non allié utilisé dans les implants chirurgicaux,1996-12-05,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[72596],"['en','fr']",2,"<p>Specifies the characteristics of, and corresponding test methods for, unalloyed tantalum in form of sheets, rods and wires used in the manufacture of surgical implants.</p>"

22927,IS,,ISO 13784-1:2002,Reaction-to-fire tests for sandwich panel building systems — Part 1: Test method for small rooms,Essais de réaction au feu des systèmes de fabrication de panneaux de type sandwich — Partie 1: Méthode d'essai pour des chambres de petite taille,2002-12-02,1,['13.220.50'],ISO/TC 92/SC 1,9599,,[53738],['en'],24,"<p>ISO 13874-1:2002 specifies a test method for determining the reaction to fire of sandwich panel building systems for small rooms and the resulting flame spread on or within the sandwich panel building construction when it is exposed to heat from a simulated internal fire with flames impinging directly on its internal corner. The test method is not intended f

30292,IS,,ISO 13784-2:2002,Reaction-to-fire tests for sandwich panel building systems — Part 2: Test method for large rooms,Essais de réaction au feu des systèmes de fabrication de panneaux de type sandwich — Partie 2: Méthode d'essai pour des chambres de grande taille,2002-12-06,1,['13.220.50'],ISO/TC 92/SC 1,9599,,[78284],['en'],14,"<p>ISO 13784-2:2002 specifies a test method for determining the reaction to fire of sandwich panel building systems for large rooms and the resulting flame spread on or within the sandwich panel building construction when it is exposed to heat from a simulated internal fire with flames impinging directly on its internal corner. The test method is not intended f

22929,IS,,ISO 13786:1999,Thermal performance of building components — Dynamic thermal characteristics — Calculation methods,Performance thermique des composants de bâtiment — Caractéristiques thermiques dynamiques — Méthodes de calcul,1999-09-23,1,"['91.060.01','91.120.10']",ISO/TC 163/SC 2,9599,,[40892],"['en','fr']",17,

40892,IS,,ISO 13786:2007,Thermal performance of building components — Dynamic thermal characteristics — Calculation methods,Performance thermique des composants de bâtiment — Caractéristiques thermiques dynamiques — Méthodes de calcul,2007-12-06,2,"['91.060.01','91.120.10']",ISO/TC 163/SC 2,9599,[22929],[65711],"['en','fr']",22,"<p>ISO 13786:2007 specifies the characteristics related to the dynamic thermal behaviour of a complete building component and provides methods for their calculation. It also specifies the information on building materials required for the use of the building component. Since the characteristics depend on the way materials are combined to form building components, ISO

22203,IS,,ISO 13788:2001,Hygrothermal performance of building components and building elements — Internal surface temperature to avoid critical surface humidity and interstitial condensation — Calculation methods,Performance hygrothermique des composants et parois de bâtiments — Température superficielle intérieure permettant d'éviter l'humidité superficielle critique et la condensation dans la masse — Méthodes de calcul,2001-07-05,1,"['91.060.01','91.120.10']",ISO/TC 163/SC 2,9599,,[51615],"['en','fr']",31,

22205,IS,,ISO 13789:1999,Thermal performance of buildings — Transmission heat loss coefficient — Calculation method,Performance thermique des bâtiments — Coefficient de déperdition par transmission — Méthode de calcul,1999-09-02,1,['91.120.10'],ISO/TC 163/SC 2,9599,,[40894],"['en','fr']",8,

40894,IS,,ISO 13789:2007,Thermal performance of buildings — Transmission and ventilation heat transfer coefficients — Calculation method,Performance thermique des bâtiments — Coefficients de transfert thermique par transmission et par renouvellement d'air — Méthode de calcul,2007-12-03,2,['91.120.10'],ISO/TC 163/SC 2,9599,[22205],[65713],"['en','fr']",18,"<p>ISO 13789:2007 specifies a method and provides conventions for the calculation of the steady-state transmission and ventilation heat transfer coefficients of whole buildings and parts of buildings. It is applicable both to heat loss (internal temperature higher than external temperature) and to heat gain (internal temperature lower than

37057,IS,,ISO 13790:2004,Thermal performance of buildings — Calculation of energy use for space heating,Performance thermique des bâtiments — Calcul des besoins d'énergie pour le chauffage des locaux,2004-06-16,1,['91.120.10'],ISO/TC 163/SC 2,9599,,[41974],['en'],59,"<p>ISO 13790:2004 gives a simplified calculation method for assessment of the annual energy use for space heating of a residential or a non-residential building, or a part of it, which will be referred to as 'the building'.</p><p>It does not apply to buildings with air conditioning systems likely to provide space cooling during the heating season.</p><p>This method includes the calculation of: the heat losses of the building whe

41974,IS,,ISO 13790:2008,Energy performance of buildings — Calculation of energy use for space heating and cooling,Performance énergétique des bâtiments — Calcul des besoins d'énergie pour le chauffage et le refroidissement des locaux,2008-02-18,2,['91.120.10'],ISO/TC 163/SC 2,9599,[37057],[65696],"['en','fr']",162,"<p>ISO 13790:2008 gives calculation methods for assessment of the annual energy use for space heating and cooling of a residential or a non-residential building, or a part of it, referred to as “the building”.</p><p>This method includes the calculation of:</p><ul><li> the heat transfer by transmission and ventilation of the building zone when heated or cooled to cons

37058,IS,,ISO 13791:2004,Thermal performance of buildings — Calculation of internal temperatures of a room in summer without mechanical cooling — General criteria and validation procedures,Performance thermique des bâtiments — Calcul des températures intérieures en été d'un local sans dispositif de refroidissement — Critères généraux et méthodes de calcul,2004-10-27,1,['91.120.10'],ISO/TC 163/SC 2,9599,,[51614],"['en','fr']",84,"<p>ISO 13791:2004 specifies the assumptions, boundary conditions, equations and validation tests for a calculation procedure, under transient hourly conditions, of the internal temperatures (air and operative) during the warm period, of a single room without any cool

51614,IS,,ISO 13791:2012,Thermal performance of buildings — Calculation of internal temperatures of a room in summer without mechanical cooling — General criteria and validation procedures,Performance thermique des bâtiments — Calcul des températures intérieures en été d'un local sans dispositif de refroidissement — Critères généraux et procédures de validation,2012-03-15,2,['91.120.10'],ISO/TC 163/SC 2,9599,[37058],"[65698,65696]","['en','fr']",96,"<p>ISO 13791:2011 specifies the assumptions, boundary conditions, equations and validation tests for a calculation procedure, under transient hourly conditions, of the internal temperatures (air and operative) during warm periods, of a single roo

37059,IS,,ISO 13792:2005,Thermal performance of buildings — Calculation of internal temperatures of a room in summer without mechanical cooling — Simplified methods,Performance thermique des bâtiments — Calcul des températures intérieures en été d'un local sans dispositif de refroidissement mécanique — Méthodes simplifiées,2005-03-07,1,['91.120.10'],ISO/TC 163/SC 2,9599,,[51621],"['en','fr']",49,"<p>ISO 13792:2005 specifies the required input data for simplified calculation methods for determining the maximum, average and minimum daily values of the operative temperature of a room in the warm period to define the characteristics of a room in order to avoid overheating in summer at the design

51621,IS,,ISO 13792:2012,Thermal performance of buildings — Calculation of internal temperatures of a room in summer without mechanical cooling — Simplified methods,Performance thermique des bâtiments — Calcul des températures intérieures en été d'un local sans dispositif de refroidissement mécanique — Méthodes simplifiées,2012-03-15,2,['91.120.10'],ISO/TC 163/SC 2,9599,[37059],"[65698,65696]","['en','fr']",54,"<p>ISO 13792:2011 specifies the required input data for simplified calculation methods for determining the maximum, average and minimum daily values of the operative temperature of a room in warm periods: </p><p>a) to define the characteristics of a room at the design stage in ord

22933,IS,,ISO 13794:1999,Ambient air — Determination of asbestos fibres — Indirect-transfer transmission electron microscopy method,Air ambiant — Dosage des fibres d'amiante — Méthode par microscopie électronique à transmission par transfert indirect,1999-08-12,1,['13.040.20'],ISO/TC 146/SC 3,9599,,[75576],['en'],64,

54296,IS,,ISO 13795:2012,Ships and marine technology — Ship's mooring and towing fittings — Welded steel bollards for sea-going vessels,Navires et technologie maritime — Corps-morts et ferrures de remorquage de navires — Bittes d'amarrage en acier soudées pour navires de haute mer,2012-06-25,1,"['47.040','47.020.50']",ISO/TC 8/SC 4,9599,,[74618],['en'],12,"<p>This International Standard specifies the design, size and technical requirements for welded steel bollards suitable for installation on sea-going vessels to meet normal mooring and towing requirements.</p>"

54297,IS,,ISO 13797:2012,Ships and marine technology — Ship's mooring and towing fittings — Cruciform bollards,Navires et technologie maritime — Corps-morts et ferrures de remorquage de navires — Croisillons,2012-06-25,1,['47.020.50'],ISO/TC 8/SC 4,9599,,[74617],['en'],7,"<p>This International Standard specifies the design, size and technical requirements for cruciform bollards suitable for installation on sea-going vessels to meet normal mooring and towing requirements.</p>"

54298,IS,,ISO 13798:2012,Ships and marine technology — Ship's mooring and towing fittings — Recessed bitts (Steel plate type),Navires et technologie maritime — Corps-morts et ferrures de remorquage de navires — Bittes d'amarrage encastrées (type plaques d'acier),2012-06-25,1,['47.020.50'],ISO/TC 8/SC 4,9599,,[74619],['en'],6,"<p>This International Standard specifies the design, size and technical requirements for steel plate type recessed bitts to meet normal towing requirements.</p>"

54299,IS,,ISO 13799:2012,Ships and marine technology — Ship's mooring and towing fittings — Recessed bitts (Casting type),Navires et technologie maritime — Corps-morts et ferrures de remorquage de navires — Bittes d'amarrage encastrées (type moulage),2012-06-25,1,['47.020.50'],ISO/TC 8/SC 4,9599,,[74621],['en'],7,"<p>This International Standard specifies the design, size and technical requirements for casting type recessed bitts to meet normal towing requirements.</p>"

22948,IS,,ISO 13802:1999,"Plastics — Verification of pendulum impact-testing machines — Charpy, Izod and tensile impact-testing","Plastiques — Vérification des machines d'essai de choc pendulaire — Essais de choc Charpy, Izod et de choc-traction",1999-10-21,1,['83.200'],ISO/TC 61/SC 2,9599,,"[60017,43321]","['en','fr']",36,

33796,IS,Cor,ISO 13802:1999/Cor 1:2000,"Plastics — Verification of pendulum impact-testing machines — Charpy, Izod and tensile impact-testing — Technical Corrigendum 1","Plastiques — Vérification des machines d'essai de choc pendulaire — Essais de choc Charpy, Izod et de choc-traction — Rectificatif technique 1",2000-04-13,1,['83.200'],ISO/TC 61/SC 2,9599,,"[60017,43321]","['en','fr']",2,

60017,IS,,ISO 13802:2015,"Plastics — Verification of pendulum impact-testing machines — Charpy, Izod and tensile impact-testing","Plastiques — Vérification des machines d'essai de choc pendulaire — Essais de choc Charpy, Izod et de choc-traction",2015-06-02,2,['83.200'],ISO/TC 61/SC 2,9599,"[22948,33796]",[85823],"['en','fr']",33,"<p>ISO 13802:2015 specifies frequency and methods for the verification of pendulum impact-testing machines used for the Charpy impact test, Izod impact test, and tensile impact test described in ISO 179‑1, ISO 180, and ISO 8256, respectively. Verification of instrumented impact machines is covered insofar as the geometrical and physical properties of instrumented m

22620,IS,,ISO 13803:2000,Paints and varnishes — Determination of reflection haze on paint films at 20 degrees,Peintures et vernis — Détermination du flou spéculaire sur des feuils de peinture à 20 degrés,2000-05-04,1,['87.040'],ISO/TC 35/SC 9,9599,,[56802],"['en','fr']",9,

22969,IS,,ISO 13804:1999,Vitreous and porcelain enamels for aluminium — Production of specimens for testing,Émaux vitrifiés déposés sur l'aluminium — Fabrication des échantillons pour essais,1999-11-25,1,['25.220.50'],ISO/TC 107,9599,,[44934],"['en','fr']",3,

22971,IS,,ISO 13806:1999,Vitreous and porcelain enamels — Corrosion tests in closed systems,Émaux vitrifiés — Essais de corrosion en milieux fermés,1999-11-25,1,['25.220.50'],ISO/TC 107,9599,,[44897],"['en','fr']",8,

22972,IS,,ISO 13807:1999,Vitreous and porcelain enamels — Determination of crack formation temperature in the thermal shock testing of enamels for the chemical industry,Émaux vitrifiés — Détermination de la température de fissuration par choc thermique d'émaux pour l'industrie chimique,1999-12-09,1,['25.220.50'],ISO/TC 107,9599,,[83826],"['en','fr']",6,<p>This International Standard specifies a test method for the determination of the crack formation temperature of</p><p>enamels for the chemical industry by subjecting enamelled steel specimens to thermal shock using cold water.</p><p>The value of the crack formation temperature measured according to this test method is not valid for the fini

34670,IS,Cor,ISO 13807:1999/Cor 1:2000,Vitreous and porcelain enamels — Determination of crack formation temperature in the thermal shock testing of enamels for the chemical industry — Technical Corrigendum 1,Émaux vitrifiés — Détermination de la température de fissuration par choc thermique d'émaux pour l'industrie chimique — Rectificatif technique 1,2000-10-19,1,['25.220.50'],ISO/TC 107,9599,,[83826],"['en','fr']",1,

54306,IS,,ISO 13810:2015,Tourism services — Industrial tourism — Service provision,Services touristiques — Tourisme industriel — Prestation de services,2015-05-22,1,"['03.200.01','03.080.30']",ISO/TC 228,9599,,[80835],"['en','fr']",16,"<p>ISO 13810:2015 establishes general requirements for industrial tourism offered by service providers intending to transmit knowledge of production, scientific and technical activities, both present and past, based on processes, know-how, products or services.</p><p>The requirements in ISO 13810:2015 are applicable to all the services of industrial tourism (visits and additional offer), dealing with living industry, industrial heritage, or a combination of bo

22992,IS,,ISO 13819-1:1995,Petroleum and natural gas industries — Offshore structures — Part 1: General requirements,Industries du pétrole et du gaz naturel — Structures en mer — Partie 1: Exigences générales,1995-12-27,1,['75.180.10'],ISO/TC 67/SC 7,9599,,[33684],"['en','fr']",30,"<p>Specifies general principles for the design and assessment of structures subjected to known or foreseeable types of actions. The principles specified are applicable worldwide and are applicable to all types of materials used including steel, concrete, aluminium etc..</p>"

22993,IS,,ISO 13819-2:1995,Petroleum and natural gas industries — Offshore structures — Part 2: Fixed steel structures,Industries du pétrole et du gaz naturel — Structures en mer — Partie 2: Structures fixes en acier,1995-12-27,1,['75.180.10'],ISO/TC 67/SC 7,9599,,[27507],"['en','fr']",225,"<p>Contains guidelines for the design of steel, fixed offshore platforms and contains provisions for specific regional areas. Applicable to the design of complete platform structures including substructures, topside structures and foundations. Specifies design principles that are also applicable to the successive stages in construction (fabrication, transportation and installation).</p>"

5915,IS,,ISO 1382:1982,Rubber — Vocabulary,Caoutchouc — Vocabulaire,1982-10-01,2,"['83.060','01.040.83']",ISO/TC 45,9599,,[21815],"['en','fr','ru']",28,

5916,IS,Add,ISO 1382:1982/Add 1:1982,Rubber — Vocabulary — Addendum 1,Caoutchouc — Vocabulaire — Additif 1,1982-05-01,2,"['83.060','01.040.83']",ISO/TC 45,9599,,[21815],"['en','fr','ru']",4,

5924,IS,Add,ISO 1382:1982/Add 9:1987,Rubber — Vocabulary — Addendum 9,Caoutchouc — Vocabulaire — Additif 9,1987-06-18,2,"['83.060','01.040.83']",ISO/TC 45,9599,,[5925],"['en','fr','ru']",5,

5926,IS,Amd,ISO 1382:1982/Amd 1:1986,Rubber — Vocabulary — Amendment 1,Caoutchouc — Vocabulaire — Amendement 1,1986-05-01,2,"['83.060','01.040.83']",ISO/TC 45,9599,,[21815],"['en','fr','ru']",1,

21815,IS,,ISO 1382:1996,Rubber — Vocabulary,Caoutchouc — Vocabulaire,1996-08-15,3,"['83.060','01.040.83']",ISO/TC 45,9599,"[5926,5915,5916]",[34800],"['en','fr','ru']",73,<p>Defines terms used in the rubber industry. Replaces the second edition.</p>

34800,IS,,ISO 1382:2002,Rubber — Vocabulary,Caoutchouc — Vocabulaire,2002-10-10,4,"['83.060','01.040.83']",ISO/TC 45,9599,"[21815,23791]","[42042,38802]","['en','fr','ru']",88,

42042,IS,,ISO 1382:2008,Rubber — Vocabulary,Caoutchouc — Vocabulaire,2008-04-02,5,"['83.060','01.040.83']",ISO/TC 45,9599,[34800],[60252],"['en','fr']",80,<p>ISO 1382:2008 is a bilingual (English/French) vocabulary containing the definitions of approximately 400 terms in general use in the rubber industry.</p>

60252,IS,,ISO 1382:2012,Rubber — Vocabulary,Caoutchouc — Vocabulaire,2012-10-08,6,"['83.060','01.040.83']",ISO/TC 45,9599,[42042],[68018],"['en','fr','ru']",118,<p>ISO 1382:2012 is a trilingual (English/French/Russian) vocabulary containing the definitions of approximately 400 terms in general use in the rubber industry.</p>

68018,IS,,ISO 1382:2020,Rubber — Vocabulary,Caoutchouc — Vocabulaire,2020-10-28,7,"['83.060','01.040.83']",ISO/TC 45,9599,[60252],[88693],"['en','fr']",67,"<p>This document establishes a vocabulary of and is limited to those terms in general use throughout the rubber industry.</p><p>It does not define terms intended for particular rubber products, some of which are given in the vocabulary standards listed in the Bibliography.</p><p>It does not define terms that are generally understood or adequately defined in other readily available sources such as general dictionaries.</p><p>The terms are listed in the alphabetical order of the English terms, with an index to the corresponding English term

21858,IS,,ISO 13820:1996,"Paper, board and corrugated fibreboard — Description and calibration of compression-testing equipment","Papier, carton et carton ondulé — Description et étalonnage du matériel pour essai de compression",1996-09-19,1,['85.100'],ISO/TC 6/SC 2,9599,,[62183],"['en','fr']",6,"<p>Specifies the essential characteristics and the principles of calibration of compression testing machines used in testing of paper, board and corrugated fibreboard.</p>"

62183,IS,,ISO 13820:2014,"Paper, board and corrugated fibreboard — Description and calibration of compression-testing equipment","Papier, carton et carton ondulé — Description et étalonnage du matériel pour essai de compression",2014-04-14,2,['85.100'],ISO/TC 6/SC 2,9599,[21858],[80329],['en'],6,"<p>ISO 13820:2014 specifies the essential characteristics and the principles of calibration of compression testing equipment used in the testing of paper, board, and corrugated fibreboard.</p>"

20672,IS,,ISO 13821:2002,Corrugated fibreboard — Determination of edgewise crush resistance — Waxed edge method,Carton ondulé — Détermination de la résistance à la compression sur chant — Méthode du bord paraffiné,2002-09-12,1,['85.060'],ISO/TC 6/SC 2,9599,,[80323],"['en','fr']",5,"<p>This International Standard specifies a method for the determination of the edgewise crush resistance of corrugated fibreboard. The force is applied in the direction of the flute axis.</p><p>This method is applicable to single-wall (double-faced), double-wall, and triple-wall corrugated fibreboard. It may also be used to test samples taken from corrugated cases and other converted products.</p><p>While the met

23006,IS,,ISO 13822:2001,Bases for design of structures — Assessment of existing structures,Bases du calcul des constructions — Évaluation des constructions existantes,2001-12-20,1,['91.080.01'],ISO/TC 98/SC 2,9599,,[46556],['en'],35,

44140,IS,,ISO 13824:2009,Bases for design of structures — General principles on risk assessment of systems involving structures,Bases du calcul des constructions — Principes généraux sur l'évaluation du risque pour les systèmes comprenant des structures,2009-11-12,1,['91.080.01'],ISO/TC 98/SC 2,9599,,[71005],['en'],43,"<p>ISO 13824:2009 specifies general principles on risk assessment of systems involving structures. The focus is on strategic and operational decision-making related to design, assessment, maintenance and decommissioning of structures. This also includes formulation and calibration of related codes and standards. Systems involving structures can expose stakeholders at various l

40670,IS,,ISO 13837:2008,Road vehicles — Safety glazing materials — Method for the determination of solar transmittance,Véhicules routiers — Vitrages de sécurité — Méthode de détermination du facteur de transmission du rayonnement solaire,2008-04-07,1,"['43.040.60','81.040.30']",ISO/TC 22/SC 35,9599,,[76159],['en'],16,"<p>ISO 13837:2008 specifies test methods to determine the direct and total solar transmittance of safety glazing materials for road vehicles. Two computational conventions (denoted convention “A” and convention “B”) are included, both of which are consistent with current international needs and practices.</p><p>ISO 13837:2008 applies to monolithic or laminated, clear or tinted

33114,IS,,ISO 13844:2000,Plastics piping systems — Elastomeric-sealing-ring-type socket joints of unplasticized poly(vinyl chloride) (PVC-U) for use with PVC-U pipes — Test method for leaktightness under negative pressure,Systèmes de canalisations en plastiques — Emboîtures avec bagues d'étanchéité en élastomères en poly(chlorure de vinyle) non plastifié (PVC-U) pour les tubes PVC-U — Méthode d'essai d'étanchéité sous pression négative,2000-03-23,1,"['23.040.20','91.140.60']",ISO/TC 138/SC 2,9599,,[61255],"['en','fr']",4,

61255,IS,,ISO 13844:2015,"Plastics piping systems — Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes — Test method for leaktightness under negative pressure, angular deflection and deformation","Systèmes de canalisations en plastiques — Assemblages par emboîture à bague d'étanchéité en élastomère pour les tubes sous pression plastiques — Méthode d'essai pour l'étanchéité sous pression négative, déviation angulaire et déformation",2015-02-26,2,"['23.040.20','91.140.60']",ISO/TC 138/SC 5,9599,[33114],[82024],"['en','fr']",6,"<p>ISO 13844:2015 specifies a method for testing the leak tightness under negative pressure, angular deflection, and deformation of assemble

33113,IS,,ISO 13845:2000,Plastics piping systems — Elastomeric-sealing-ring-type socket joints for use with unplasticized poly(vinyl chloride) (PVC-U) pipes — Test method for leaktightness under internal pressure and with angular deflection,Systèmes de canalisations en plastique — Assemblages par emboîture à bague d'étanchéité en élastomère pour tubes en poly(chlorure de vinyle) non plastifié (PVC-U) — Méthode d'essai d'étanchéité avec pression interne et avec déviation angulaire,2000-03-23,1,"['23.040.20','23.040.01','91.140.60']",ISO/TC 138/SC 2,9599,,[61256],"['en','fr']",3,

23080,IS,,ISO 13847:2000,Petroleum and natural gas industries — Pipeline transportation systems — Welding of pipelines,Industries du pétrole et du gaz naturel — Conduites pour systèmes de transport — Soudage des conduites,2000-10-12,1,['75.200'],ISO/TC 67/SC 2,9599,,[45120],['en'],50,

36163,IS,Cor,ISO 13847:2000/Cor 1:2001,Petroleum and natural gas industries — Pipeline transportation systems — Welding of pipelines — Technical Corrigendum 1,Industries du pétrole et du gaz naturel — Conduites pour systèmes de transport — Soudage des conduites — Rectificatif technique 1,2001-12-13,1,['75.200'],ISO/TC 67/SC 2,9599,,[45120],['en'],1,

22582,IS,,ISO 13849-1:1999,Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design,Sécurité des machines — Parties des systèmes de commande relatives à la sécurité — Partie 1: Principes généraux de conception,1999-11-25,1,['13.110'],ISO/TC 199,9599,,[34931],"['en','fr']",31,

34931,IS,,ISO 13849-1:2006,Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design,Sécurité des machines — Parties des systèmes de commande relatives à la sécurité — Partie 1: Principes généraux de conception,2006-10-30,2,['13.110'],ISO/TC 199,9599,[22582],[69883],"['en','fr']",85,"<p>ISO 13849-1:2006 provides safety requirements and guidance on the principles for the design and integration of safety-related parts of control systems (SRP/CS), includi

53570,IS,Cor,ISO 13849-1:2006/Cor 1:2009,Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design — Technical Corrigendum 1,Sécurité des machines — Parties des systèmes de commande relatives à la sécurité — Partie 1: Principes généraux de conception — Rectificatif technique 1,2009-02-18,2,['13.110'],ISO/TC 199,9599,,"[69883,62494]","['en','fr']",2,

69883,IS,,ISO 13849-1:2015,Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design,Sécurité des machines — Parties des systèmes de commande relatives à la sécurité — Partie 1: Principes généraux de conception,2015-12-04,3,['13.110'],ISO/TC 199,9599,"[62904,34931,53570]",[73481],"['en','fr']",86,"<p>ISO 13849-1:2015 provides safety requirements and guidance on the principles for the design and integration of safety-related parts of control systems (SR

36180,IS,,ISO 13849-2:2003,Safety of machinery — Safety-related parts of control systems — Part 2: Validation,Sécurité des machines — Parties des systèmes de commande relatifs à la sécurité — Partie 2: Validation,2003-08-22,1,['13.110'],ISO/TC 199,9599,,[53640],"['en','fr']",50,"<p>ISO 13849-2:2003 specifies the procedures and conditions to be followed for the validation by analysis and testing of:</p><ol><li>the safety functions provided and</li><li>the category achieved</li></ol><p>for the safety-related parts of the control system in compliance with EN 954-1 (ISO 13849-1), using the design rationale provided by the designer.</p><p>This International Standard does not give complete validat

22579,IS,,ISO 13850:1996,Safety of machinery — Emergency stop — Principles for design,Sécurité des machines — Arrêt d'urgence — Principes de conception,1996-10-31,1,['13.110'],ISO/TC 199,9599,,[39078],"['en','fr']",5,"<p>Specifies functional requirements and design principles for the emergency stop of machinery, independent of the type of energy used to control the function.</p>"

39078,IS,,ISO 13850:2006,Safety of machinery — Emergency stop — Principles for design,Sécurité des machines — Arrêt d'urgence — Principes de conception,2006-11-10,2,['13.110'],ISO/TC 199,9599,[22579],[59970],"['en','fr']",6,"<p>ISO 13850:2006 specifies functional requirements and design principles for the emergency stop function on machinery, independent of the type of energy used to control the function. It is applicable to all machinery except for machines in which the provision of emergency stop would not lessen the risk, and hand-held portable machines and hand-guided machines. It does not deal with functions such as reversal or limitation of motion, deflection, shielding, braking or dis

35560,IS,,ISO 13851:2002,Safety of machinery — Two-hand control devices — Functional aspects and design principles,Sécurité des machines — Dispositifs de commande bimanuelle — Aspects fonctionnels et principes de conception,2002-03-21,1,['13.110'],ISO/TC 199,9599,,[70295],"['en','fr']",23,"<p>This International Standard specifies the safety requirements of a two-hand control device and the dependency of the output signal from the input signals.</p><p>It describes the main characteristics of two-hand control devices for the achievement of safety and sets out combinations of functional characteristics for three types. It does not apply to devices intended to be used as enabling devices, as hol

22597,IS,,ISO 13852:1996,Safety of machinery — Safety distances to prevent danger zones being reached by the upper limbs,Sécurité des machines — Distances de sécurité pour empêcher l'atteinte des zones dangereuses par les membres supérieurs,1996-12-19,1,['13.110'],ISO/TC 199,9599,,[39255],"['en','fr']",10,<p>Gives values for safety distances to prevent danger zones being reached by the upper limbs of persons of 3 years of age and above without additional aid. The distances apply when adequate safety can be achieved by distances alone.</p>

22577,IS,,ISO 13853:1998,Safety of machinery — Safety distances to prevent danger zones being reached by the lower limbs,Sécurité des machines — Distances de sécurité pour empêcher l'atteinte des zones dangereuses par les membres inférieurs,1998-09-17,1,['13.110'],ISO/TC 199,9599,,[39255],"['en','fr']",6,

22598,IS,,ISO 13854:1996,Safety of machinery — Minimum gaps to avoid crushing of parts of the human body,Sécurité des machines — Écartements minimaux pour prévenir les risques d'écrasement de parties du corps humain,1996-12-19,1,['13.110'],ISO/TC 199,9599,,"[66459,38387]","['en','fr']",5,"<p>Purpose is to enable the user (e.g. standard makers, designers of machinery) to avoid hazards from crushing zones. Specifies minimum gaps relative to parts of the human body. Applicable when adequate safety can be achieved by this method.</p>"

35562,IS,,ISO 13855:2002,Safety of machinery — Positioning of protective equipment with respect to the approach speeds of parts of the human body,Sécurité des machines —Positionnement des dispositifs de protection par rapport à la vitesse d'approche des parties du corps,2002-01-31,1,['13.110'],ISO/TC 199,9599,,[42845],"['en','fr']",19,"<p>This International Standard provides parameters based on values for hand/arm and approach speeds and the methodology to determine the minimum distances from sensing or actuating devices of protective equipment to a danger zone.</p><p>These specific devices are:</p><ol><li>trip devices as defined in EN 292-1:1991, 3.23.5 (specifically electro-sensitive prote

42845,IS,,ISO 13855:2010,Safety of machinery — Positioning of safeguards with respect to the approach speeds of parts of the human body,Sécurité des machines — Positionnement des moyens de protection par rapport à la vitesse d'approche des parties du corps,2010-04-19,2,['13.110'],ISO/TC 199,9599,[35562],[80590],"['en','fr']",40,"<p>ISO 13855:2010 establishes the positioning of safeguards with respect to the approach speeds of parts of the human body.</p><p>It specifies parameters based on values for approach speeds of parts of the human body and provides a methodology to determine the minimum distances to a hazard zone from the detection zone or from actuating devices of safeguards.</p><p>Th

22583,IS,,ISO 13856-1:2001,Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for design and testing of pressure-sensitive mats and pressure-sensitive floors,Sécurité des machines — Dispositifs de protection sensibles à la pression — Partie 1: Principes généraux de conception et d'essai des tapis et planchers sensibles à la pression,2001-08-09,1,['13.110'],ISO/TC 199,9599,,[57017],"['en','fr']",42,

39060,IS,,ISO 13856-2:2005,Safety of machinery — Pressure-sensitive protective devices — Part 2: General principles for the design and testing of pressure-sensitive edges and pressure-sensitive bars,Sécurité des machines — Dispositifs de protection sensibles à la pression — Partie 2: Principes généraux de conception et d'essai des bords et barres sensibles à la pression,2005-02-17,1,['13.110'],ISO/TC 199,9599,,[57108],['en'],51,"<p>ISO 13856-2:2005 specifies the general principles and requirements for the design and testing of pressure-sensitive edges and pressure-sensitive bars for use as safety devices and not as actuating devices for normal operation. It is applicable to pressure-sensitiv

42846,IS,,ISO 13856-3:2006,"Safety of machinery — Pressure-sensitive protective devices — Part 3: General principles for the design and testing of pressure-sensitive bumpers, plates, wires and similar devices","Sécurité des machines — Dispositifs de protection sensibles à la pression — Partie 3: Principes généraux de conception et d'essai des pare-chocs, plaques, câbles et dispositifs analogues sensibles à la pression",2006-10-06,1,['13.110'],ISO/TC 199,9599,,[57872],['en'],56,"<p>ISO 13856-3:2006 gives basic requirements for those pressure-sensitive protective devices, with or without an external reset facility, that are not specified in either ISO 13856-1 or ISO 13856-2, the majority of wh

39255,IS,,ISO 13857:2008,Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs,Sécurité des machines — Distances de sécurité empêchant les membres supérieurs et inférieurs d'atteindre les zones dangereuses,2008-03-03,1,['13.110'],ISO/TC 199,9599,"[22577,22597]",[69569],"['en','fr']",17,"<p>ISO 13857:2007 establishes values for safety distances in both industrial and non-industrial environments to prevent machinery hazard zones being reached. The safety distances are appropriate for protective structures. It also gives information about distances to impede free access by the lower limbs. It covers people of 14 years and older (the 5^th

23098,IS,,ISO 13860:2000,"Machinery for forestry — Forwarders — Terms, definitions and commercial specifications","Matériel forestier — Débardeuses — Termes, définitions et spécifications commerciales",2000-04-13,1,"['65.060.80','01.040.65']",ISO/TC 23/SC 15,9599,,[63993],"['en','fr']",9,

23099,IS,,ISO 13861:2000,"Machinery for forestry — Wheeled skidders — Terms, definitions and commercial specifications","Matériel forestier — Débusqueuses à roues — Termes, définitions et spécifications commerciales",2000-04-13,1,"['65.060.80','01.040.65']",ISO/TC 23/SC 15,9599,,"[82426,70952]","['en','fr']",9,<p>This International Standard specifies terminology and required information as a general framework for identifying</p><p>and describing the main dimensions and features of wheeled skidders.</p><p>It is applicable to articulated wheeled cable and grapple skidders as defined in ISO 6814.</p><p>NOTE The terminology and requirements given in this International Standard will not necessar

23100,IS,,ISO 13862:2000,"Machinery for forestry — Feller-bunchers — Terms, definitions and commercial specifications","Matériel forestier — Abatteuses-groupeuses — Termes, définitions et spécifications commerciales",2000-04-13,1,"['65.060.80','01.040.65']",ISO/TC 23/SC 15,9599,,"[70953,82427]","['en','fr']",7,<p>This International Standard specifies terminology and required information as a general framework for identifying</p><p>and describing the main dimensions and features of feller-bunchers.</p><p>It is applicable to tracked and wheeled feller-bunchers as defined in ISO 6814.</p><p>NOTE The terminology and requirements given in this International Standard will not necessarily all apply

54338,IS,,ISO 13876:2013,Soil quality — Determination of polychlorinated biphenyls (PCB) by gas chromatography with mass selective detection (GC-MS) and gas chromatography with electron-capture detection (GC-ECD),Qualité du sol — Détermination des polychlorobiphényles (PCB) par chromatographie en phase gazeuse avec détection sélective de masse (GC-MS) et chromatographie en phase gazeuse avec détection par capture d'électrons (GC-ECD),2013-11-04,1,['13.080.10'],ISO/TC 190/SC 3,9599,,[84177],['en'],29,"<p>ISO 13876:2013 specifies a method for quantitative determination of seven selected polychlorinated biphenyls (PCB28, PCB52, PCB101, PCB118, PCB138, PCB153, and PCB180) in sludge, treated biow

23178,IS,,ISO 13885-1:1998,Binders for paints and varnishes — Gel permeation chromatography (GPC) — Part 1: Tetrahydrofuran (THF) as eluent,Liants pour peintures et vernis — Chromatographie par perméation de gel (GPC) — Partie 1: Utilisation de tétrahydrofurane (THF) comme éluant,1998-12-10,1,['87.060.20'],ISO/TC 35,9599,,[44648],"['en','fr']",24,

44648,IS,,ISO 13885-1:2008,Binders for paints and varnishes — Gel permeation chromatography (GPC) — Part 1: Tetrahydrofuran (THF) as eluent,Liants pour peintures et vernis — Chromatographie par perméation de gel (GPC) — Partie 1: Utilisation de tétrahydrofurane (THF) comme éluant,2008-07-21,2,['87.060.20'],ISO/TC 35,9599,[23178],[73850],"['en','ru']",23,"<p>ISO 13885-1:2008 describes the determination of the molar-mass distribution, number-average molar mass <i>M</i>_n and mass-average molar mass <i>M</i>_w of polymers that are soluble in THF (tetrahydrofuran) by gel permeation chromatography (GPC)[also known as size exclusion chromatography (SEC)].</p><p>It i

23184,IS,,ISO 13887:1995,Cold-reduced steel sheet of higher yield strength with improved formability,Tôles laminées à froid en acier à limite d'élasticité et aptitude au formage accrues,1995-12-21,1,['77.140.50'],ISO/TC 17/SC 12,9599,,[34629],"['en','fr']",8,"<p>Applies to cold-reduced steel sheet of higher strength which is made from killed steel, and may contain phosphorus up to 0,12 % (m/m) maximum. Intended for applications where parts are to be fabricated requiring better formability than is provided by normal high yield strength steel sheet. Suitable for applications where the surface of the sheet is of prime importance.</p>"

34629,IS,,ISO 13887:2004,Cold-reduced steel sheet of higher yield strength with improved formability,Tôles laminées à froid en acier à limite d'élasticité et aptitude au formage accrues,2004-04-30,2,['77.140.50'],ISO/TC 17/SC 12,9599,[23184],[55949],"['en','fr']",11,"<p>ISO 13887:2004 establishes a system of testing for improved formability and strength of cold-reduced steel sheet in the seven grades listed in Table 1. It is suitable for applications where the surface of the sheet is of prime importance.</p><p>This International Standard is not applicable to steels designated as commercial quality or drawing qualities (see ISO 3574), steels of structural quality (see ISO 4997) or steels of h

55949,IS,,ISO 13887:2011,Cold-reduced steel sheet of higher yield strength with improved formability,Tôles laminées à froid en acier à limite d'élasticité et aptitude au formage accrues,2011-11-09,3,['77.140.50'],ISO/TC 17/SC 12,9599,[34629],[70238],['en'],7,

23253,IS,,ISO 13895:1996,Adhesives — Guidelines for the surface preparation of plastics,Adhésifs — Guide pour la préparation de surface des plastiques,1996-10-24,1,['83.180'],ISO/TC 61/SC 11,9599,,[38283],"['en','fr']",7,"<p>Describes mechanical, chemical and electrical methods of surface preparation for plastics adherends to be used prior to adhesive bonding.</p>"

35153,IS,,ISO 13897:2003,Dentistry — Amalgam capsules,Art dentaire — Capsules pour amalgame,2003-03-04,1,['11.060.10'],ISO/TC 106/SC 6,9599,,[68819],"['en','fr']",6,<p>ISO 13897:2003 specifies requirements and test methods for predosed capsules and for reusable capsules used for mixing dental amalgam alloys and mercury.</p>

39810,IS,Cor,ISO 13897:2003/Cor 1:2003,Dentistry — Amalgam capsules — Technical Corrigendum 1,Art dentaire — Capsules pour amalgame — Rectificatif technique 1,2003-12-11,1,['11.060.10'],ISO/TC 106/SC 6,9599,,[68819],"['en','fr']",1,