Withdrawn and superseded ISO standards — page 36 of 246

37429,IS,,ISO 13448-1:2005,Acceptance sampling procedures based on the allocation of priorities principle (APP) — Part 1: Guidelines for the APP approach,Règles d'échantillonnage pour acceptation fondées sur le principe d'attribution de priorités (APP) — Partie 1: Lignes directrices relatives à l'approche APP,2005-03-17,1,['03.120.30'],ISO/TC 69/SC 5,9599,,[64631],"['en','fr']",25,"<p>ISO 13448-1:2005 provides guidelines specifying the organizational principles of acceptance sampling in situations where the contract or the legislation provides for successive inspection to be carried out by different parties: the supplier, the customer and/or a third party. </p><p>These guidelines are design

37430,IS,,ISO 13448-2:2004,Acceptance sampling procedures based on the allocation of priorities principle (APP) — Part 2: Coordinated single sampling plans for acceptance sampling by attributes,Règles d'échantillonnage pour acceptation fondées sur le principe d'attribution de priorités (APP) — Partie 2: Plans d'échantillonnage simple coordonnés pour l'échantillonnage pour acceptation par attributs,2004-12-08,1,['03.120.30'],ISO/TC 69/SC 5,9599,,[69416],"['en','fr']",50,"<p>ISO 13448-2:2004 provides attributes sampling procedures and single sampling plans for successive independent inspections of the same lot conducted by the supplier, consumer and/or a third party. </p><p>ISO 13448-2:2004 ad

22026,IS,,ISO 13457:2000,Agricultural irrigation equipment — Water-driven chemical injector pumps,Matériel agricole d'irrigation — Pompes doseuses à moteur hydraulique pour l'injection de produits chimiques,2000-05-04,1,['65.060.35'],ISO/TC 23/SC 18,9599,,[43993],"['en','fr']",12,

43993,IS,,ISO 13457:2008,Agricultural irrigation equipment — Water-driven chemical injector pumps,Matériel agricole d'irrigation — Pompes doseuses à moteur hydraulique pour l'injection de produits chimiques,2008-07-30,2,['65.060.35'],ISO/TC 23/SC 18,9599,[22026],[80102],['en'],12,"<p>ISO 13457:2008 specifies the construction, operational requirements and test methods for water‑driven chemical injector pumps, used to inject chemicals into irrigation systems. The chemicals include liquid fertilizers and solutions of fertilizers and other soluble agricultural chemicals such as acids and pesticides.</p><p>ISO 13457:2008 is applicable to those pumps intended to operate at water temperatures of up

22029,IS,,ISO 13459:1997,Earth-moving machinery — Dumpers — Trainer seat/enclosure,Engins de terrassement — Tombereaux — Enceinte/siège de l'instructeur,1997-04-03,1,['53.100'],ISO/TC 127/SC 2,9599,,[51976],"['en','fr']",4,

5909,IS,,ISO 1346:1975,Ropes and cordage — Three-strand (hawser-laid) and eight-strand (plaited) polypropylene monofilament or film ropes — Required characteristics,Cordages en monofilaments et en lames textiles de polypropylène à trois torons câblés et à huit torons tressés — Caractéristiques requises,1975-10-01,1,['59.080.50'],ISO/TC 38,9599,,[5910],['en'],2,

5910,IS,,ISO 1346:1990,Ropes — Polypropylene — Specification,Cordages — Polypropylène — Spécifications,1990-11-01,2,['59.080.50'],ISO/TC 38,9599,[5909],[36583],"['en','fr']",4,"<p>Specifies the main characteristics of 3- and 4-strand laid ropes and 8-strand plaited ropes and gives rules for their designation. Relates to the definitions given in ISO 1968. The main characteristics are shown in tables. This second edition cancels and replaces the first edition ISO 1346:1975, of which it constitutes a technical revision.</p>"

36583,IS,,ISO 1346:2004,"Fibre ropes — Polypropylene split film, monofilament and multifilament (PP2) and polypropylene high tenacity multifilament (PP3) — 3-, 4- and 8-strand ropes","Cordages en fibres — Film fibrillé, monofilament et multifilament de polypropylène (PP2) et multifilament de polypropylène haute ténacité (PP3) — Cordages à 3, 4 et 8 torons",2004-10-26,3,['59.080.50'],ISO/TC 38,9599,[5910],[56632],"['en','fr']",6,<p>ISO 1346:2004 specifies requirements for 3-strand hawser-laid and 4-strand shroud laid ropes and 8-strand braided ropes for general service made of polypropylene and gives rules for their designation.</p>

56632,IS,,ISO 1346:2012,"Fibre ropes — Polypropylene split film, monofilament and multifilament (PP2) and polypropylene high-tenacity multifilament (PP3) — 3-, 4-, 8- and 12-strand ropes","Cordages en fibres — Film fibrillé, monofilament et multifilament de polypropylène (PP2) et multifilament de polypropylène haute ténacité (PP3) — Cordages à 3, 4, 8 et 12 torons",2012-07-26,4,['59.080.50'],ISO/TC 38,9599,[36583],[76536],"['en','fr']",7,"<p>ISO 1346:2012 specifies requirements for 3-strand hawser-laid and 4-strand shroud-laid ropes, 8-strand braided ropes and 12-strand braided ropes for general service made of polypropylene and gives rules for their designation.</p>"

22032,IS,,ISO 13460:1998,Agricultural irrigation equipment — Plastics saddles for polyethylene pressure pipes,Matériel agricole d'irrigation — Selles de dérivation en matière plastique pour le raccordement de tuyau en polyéthylène utilisé sous pression,1998-12-03,1,['65.060.35'],ISO/TC 23/SC 18,9599,,[61890],"['en','fr']",10,

22036,IS,,ISO 13465:1997,Determination of neptunium in nitric acid solutions by molecular absorption spectrophotometry,Détermination du neptunium dans les solutions d'acide nitrique par spectrophotométrie d'absorption moléculaire,1997-05-29,1,['27.120.30'],ISO/TC 85/SC 5,9599,,[44275],"['en','fr']",6,

44275,IS,,ISO 13465:2009,Nuclear energy — Nuclear fuel technology — Determination of neptunium in nitric acid solutions by spectrophotometry,Énergie nucléaire — Technologie du combustible nucléaire — Détermination du neptunium dans les solutions d'acide nitrique par spectrophotométrie,2009-05-05,2,['27.120.30'],ISO/TC 85/SC 5,9599,[22036],[86852],"['en','fr']",6,"<p>ISO 13465:2009 specifies an analytical method for determining the neptunium concentration by spectrophotometry, with a standard deviation of about 5 %, in nitric acid solutions of nuclear reactor irradiated fuels, at different steps of the process in a nuclear fuel reprocessing plant. The method is applicable to aliquots containi

22055,IS,,ISO 13468-1:1996,Plastics — Determination of the total luminous transmittance of transparent materials — Part 1: Single-beam instrument,Plastiques — Détermination du facteur de transmission du flux lumineux total des matériaux transparents — Partie 1: Instrument à faisceau unique,1996-08-08,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[77312],"['en','fr']",7,"<p>Deals with the determination of the total luminous transmittance, in the visible region of the spectrum, of planar transparent and substantially colourless plastics, using a single-beam photometer with a specified CIE standard light source and photodetector. Does not apply to plastics which contain fluorescent substances.</p>" 2205

22056,IS,,ISO 13468-2:1999,Plastics — Determination of the total luminous transmittance of transparent materials — Part 2: Double-beam instrument,Plastiques — Détermination du facteur de transmission du flux lumineux total des matériaux transparents — Partie 2: Instrument à double faisceau,1999-05-13,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[81839],"['en','fr']",6,"<p>This part of ISO 13468 covers the determination of the total luminous transmittance, in the visible region of the</p><p>spectrum, of planar transparent and substantially colourless plastics, using a double-beam scanning spectrophotometer.</p><p>This part of ISO 13468 cannot be used for plastics which contain fluorescent materials.<

35387,IS,,ISO 13472-1:2002,Acoustics — Measurement of sound absorption properties of road surfaces in situ — Part 1: Extended surface method,Acoustique — Mesurage in situ des propriétés d'absorption acoustique des revêtements de chaussées — Partie 1: Méthode de la surface étendue,2002-06-27,1,"['17.140.30','93.080.20']",ISO/TC 43/SC 1,9599,,[77032],"['en','fr']",26,"<p>This part of ISO 13472 describes a test method for measuring <i>in situ </i>the sound absorption coefficient of road</p><p>surfaces as a function of frequency in the range from to .</p><p>Normal incidence is assumed. However, the test method can be applied at oblique incidence although with some</p><p>limitations (see annex F)

32304,IS,,ISO 13472-2:2010,Acoustics — Measurement of sound absorption properties of road surfaces in situ — Part 2: Spot method for reflective surfaces,Acoustique — Mesurage in situ des propriétés d'absorption acoustique des revêtements de chaussées — Partie 2: Méthode ponctuelle pour les surfaces réfléchissantes,2010-04-28,1,"['17.140.30','93.080.20']",ISO/TC 43/SC 1,9599,,"[77372,84925]",['en'],20,"<p>ISO 13472-2:2010 specifies a test method for measuring <i>in situ</i> the sound absorption coefficient of road surfaces for the one-third-octave-band frequencies ranging from 250 Hz to 1 600 Hz under normal incidence conditions. For special purposes, the frequency range can be changed by mod

25637,IS,,ISO 13473-1:1997,Characterization of pavement texture by use of surface profiles — Part 1: Determination of Mean Profile Depth,Caractérisation de la texture d'un revêtement de chaussée à partir de relevés de profils de la surface — Partie 1: Détermination de la profondeur moyenne du profil,1997-09-04,1,"['17.140.30','93.080.20']",ISO/TC 43/SC 1,9599,,[45111],"['en','fr']",19,

40280,IS,,ISO 13473-5:2009,Characterization of pavement texture by use of surface profiles — Part 5: Determination of megatexture,Caractérisation de la texture d'un revêtement de chaussée à partir de relevés de profils de la surface — Partie 5: Détermination de la mégatexture,2009-03-19,1,"['17.140.30','93.080.20']",ISO/TC 43/SC 1,9599,,[84853],"['en','fr']",29,"<p>ISO 13473-5:2009 specifies procedures for determining the average depth or level of pavement surface megatexture by measuring the profile curve of a surface and calculating megatexture descriptors from this profile. The technique is designed to give meaningful and accurate measurement and description of pavement megatexture charac

22076,IS,,ISO 13477:1997,Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test),Tubes en matières thermoplastiques pour le transport des fluides — Détermination de la résistance à la propagation rapide de la fissure (RCP) — Essai à petite échelle (S4),1997-10-02,1,['23.040.20'],ISO/TC 138/SC 5,9599,[30350],[39858],"['en','fr']",9,

22077,IS,,ISO 13478:1997,Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST),Tubes en matières thermoplastiques pour le transport des fluides — Détermination de la résistance à la propagation rapide de la fissure (RCP) — Essai grandeur nature (FST),1997-04-24,1,['23.040.20'],ISO/TC 138/SC 5,9599,,"[39859,30351]","['en','fr']",11,

22078,IS,,ISO 13479:1997,Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes (notch test),Tubes en polyoléfines pour le transport des fluides — Résistance à la propagation de la fissure — Méthode d'essai de la propagation lente de la fissure d'un tube entaillé (essai d'entaille),1997-04-24,1,['23.040.20'],ISO/TC 138/SC 5,9599,,[45812],"['en','fr']",9,

45812,IS,,ISO 13479:2009,Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes,Tubes en polyoléfines pour le transport des fluides — Détermination de la résistance à la propagation de la fissure — Méthode d'essai de la propagation lente de la fissure d'un tube entaillé (essai d'entaille),2009-09-03,2,['23.040.20'],ISO/TC 138/SC 5,9599,[22078],[76770],"['en','fr','ru']",9,"<p>ISO 13479:2009 specifies a test method for determining the resistance to slow crack growth of polyolefin pipes, expressed in terms of time to failure in a hydrostatic pressure test on a pipe with machined longitudinal notches

22098,IS,,ISO 13485:1996,Quality systems — Medical devices — Particular requirements for the application of ISO 9001,Systèmes qualité — Dispositifs médicaux — Exigences particulières relatives à l'application de l'ISO 9001,1996-12-26,1,"['03.100.70','11.040.01']",ISO/TC 210,9599,,[36786],"['en','fr']",10,"<p>Specifies, in conjunction with the application of ISO 9001, the quality system requirements for the design/development and, when relevant, installation and servicing of medical devices.</p>"

36786,IS,,ISO 13485:2003,Medical devices — Quality management systems — Requirements for regulatory purposes,Dispositifs médicaux — Systèmes de management de la qualité — Exigences à des fins réglementaires,2003-07-03,2,"['03.100.70','11.040.01']",ISO/TC 210,9599,[22098],[59752],"['en','fr','ru']",57,"<p>ISO 13485:2003 specifies requirements for a quality management system where an organization needs to demonstrate its ability to provide medical devices and related services that consistently mee

54724,IS,Cor,ISO 13485:2003/Cor 1:2009,Medical devices — Quality management systems — Requirements for regulatory purposes — Technical Corrigendum 1,Dispositifs médicaux — Systèmes de management de la qualité — Exigences à des fins réglementaires — Rectificatif technique 1,2009-07-17,2,"['03.120.10','11.040.01']",ISO/TC 210,9599,,[59752],"['en','fr','ru']",1,

19521,IS,,ISO 13491-1:1998,"Banking — Secure cryptographic devices (retail) — Part 1: Concepts, requirements and evaluation methods","Banque — Dispositifs cryptographiques de sécurité (services aux particuliers) — Partie 1: Concepts, prescriptions et méthodes d'évaluation",1998-06-11,1,['35.240.40'],ISO/TC 68/SC 2,9599,,[41214],"['en','fr']",21,

41214,IS,,ISO 13491-1:2007,"Banking — Secure cryptographic devices (retail) — Part 1: Concepts, requirements and evaluation methods","Banque — Dispositifs cryptographiques de sécurité (services aux particuliers) — Partie 1: Concepts, exigences et méthodes d'évaluation",2007-06-11,2,['35.240.40'],ISO/TC 68/SC 2,9599,[19521],[61137],['en'],30,"<p>ISO 13491-1:2007 specifies the requirements for secure cryptographic devices (SCDs) based on the cryptographic processes defined in ISO 9564, ISO 16609 and ISO 11568.</p><p>ISO 13491-1:2007 has two primary purposes:</p><ul><li> to state the requirements concerning both the operational characteristics of SCDs and the management of such devices th

61137,IS,,ISO 13491-1:2016,"Financial services — Secure cryptographic devices (retail) — Part 1: Concepts, requirements and evaluation methods","Services financiers — Dispositifs cryptographiques de sécurité (services aux particuliers) — Partie 1: Concepts, exigences et méthodes d'évaluation",2016-03-17,3,['35.240.40'],ISO/TC 68/SC 2,9599,[41214],[81967],['en'],33,"<p>ISO 13491-1:2016 specifies the security characteristics for secure cryptographic devices (SCDs) based on the cryptographic processes defined in ISO 9564, ISO 16609, and ISO 11568.</p><p>ISO 13491-1:2016 has two primary purposes:</p><p>- to state the security characteristics concerning both the operational characteristics o

28370,IS,,ISO 13491-2:2000,Banking — Secure cryptographic devices (retail) — Part 2: Security compliance checklists for devices used in magnetic stripe card systems,Banque — Dispositifs cryptographiques de sécurité (services aux particuliers) — Partie 2: Listes de contrôle de conformité de sécurité pour les dispositifs utilisés dans les systèmes de cartes à bande magnétique,2000-10-26,1,['35.240.40'],ISO/TC 68/SC 2,9599,,[39671],['en'],30,

39671,IS,,ISO 13491-2:2005,Banking — Secure cryptographic devices (retail) — Part 2: Security compliance checklists for devices used in financial transactions,Banque — Dispositifs cryptographiques de sécurité (services aux particuliers) — Partie 2: Listes de contrôle de conformité de sécurité pour les dispositifs utilisés dans les transactions financières,2005-06-15,2,['35.240.40'],ISO/TC 68/SC 2,9599,[28370],[61163],['en'],31,"<p>ISO 13491-2:2005 specifies checklists to be used to evaluate secure cryptographic devices (SCDs) incorporating cryptographic processes, as specified in parts 1 and 2 of ISO 9564, ISO 16609 and parts 1 to 6 of ISO 11568, in the financial services environment. IC pay

61163,IS,,ISO 13491-2:2016,Financial services — Secure cryptographic devices (retail) — Part 2: Security compliance checklists for devices used in financial transactions,Services financiers — Dispositifs cryptographiques de sécurité (services aux particuliers) — Partie 2: Listes de contrôle de conformité de sécurité pour les dispositifs utilisés dans les transactions financières,2016-03-17,3,['35.240.40'],ISO/TC 68/SC 2,9599,[39671],[72178],['en'],39,"<p>ISO 13491-2:2016 specifies checklists to be used to evaluate secure cryptographic devices (SCDs) incorporating cryptographic processes as specified in H.5, ISO 9564‑2, ISO 16609, ISO 11568‑1, ISO 11568‑2, and ISO 11568‑4 in the financial ser

72178,IS,,ISO 13491-2:2017,Financial services — Secure cryptographic devices (retail) — Part 2: Security compliance checklists for devices used in financial transactions,Services financiers — Dispositifs cryptographiques de sécurité (services aux particuliers) — Partie 2: Listes de contrôle de conformité de sécurité pour les dispositifs utilisés dans les transactions financières,2017-03-23,4,['35.240.40'],ISO/TC 68/SC 2,9599,[61163],[82277],['en'],39,"<p>ISO 13491-2:2017 specifies checklists to be used to evaluate secure cryptographic devices (SCDs) incorporating cryptographic processes as specified in ISO 9564‑1, ISO 9564‑2, ISO 16609, ISO 11568‑1, ISO 11568‑2, and ISO 11568‑4 in the financ

20746,IS,,ISO 13492:1998,Banking — Key management related data element (retail),Banque — Élément de données lié à la gestion des clés (services aux particuliers),1998-05-14,1,['35.240.40'],ISO/TC 68/SC 2,9599,,[39668],"['en','fr']",10,

39668,IS,,ISO 13492:2007,Financial services — Key management related data element — Application and usage of ISO 8583 data elements 53 and 96,Services financiers — Élément de données lié à la gestion des clés — Application et utilisation des éléments de données 53 et 96 de l'ISO 8583,2007-12-06,2,['35.240.40'],ISO/TC 68/SC 2,9599,[20746],[73992],['en'],10,"<p>ISO 13492:2007 describes a key management related data element that can be transmitted either in transaction messages to convey information about cryptographic keys used to secure the current transaction, or in cryptographic service messages to convey information about cryptographic keys to be used to secure future transactions.</p><p>I

21238,IS,,ISO 13493:1998,Meat and meat products — Determination of chloramphenicol content — Method using liquid chromatography,Viande et produits à base de viande — Dosage du chloramphénicol — Méthode par chromatographie en phase liquide,1998-09-03,1,['67.120.10'],ISO/TC 34/SC 6,9599,,[76930],['en'],8,

21237,IS,,ISO 13496:2000,Meat and meat products — Detection of colouring agents — Method using thin-layer chromatography,Viande et produits à base de viande — Détection des agents colorants — Méthode par chromatographie en couche mince,2000-03-02,1,['67.120.10'],ISO/TC 34/SC 6,9599,,[76933],"['en','fr']",11,"<p>This International Standard specifies a thin-layer chromatographic method for the detection of synthetic, watersoluble</p><p>colouring agents in meat and meat products.</p><p>The following colouring agents can be detected with the method:</p><p>Tartrazine Patent Blue V</p><p>Quinoline Yellow Indigotine</p><p>Sunset Yellow FCF Brilliant Black PN</p><p>Amaranth Black 7984</p><p>Ponceau

22132,IS,,ISO 13500:1998,Petroleum and natural gas industries — Drilling fluid materials — Specifications and tests,Industries du pétrole et du gaz naturel — Produits pour fluides de forage — Spécifications et essais,1998-07-16,1,['75.180.10'],ISO/TC 67/SC 3,9599,,[40032],"['en','fr']",66,

40032,IS,,ISO 13500:2006,Petroleum and natural gas industries — Drilling fluid materials — Specifications and tests,Industries du pétrole et du gaz naturel — Produits pour fluides de forage — Spécifications et essais,2006-02-09,2,['75.180.10'],ISO/TC 67/SC 3,9599,[22132],[46560],['en'],74,"<p>ISO 13500:2006 covers physical properties and test procedures for materials manufactured for use in oil-and gas-well drilling fluids. The materials covered are barite, haematite, bentonite, nontreated bentonite, OCMA grade bentonite, attapulgite, sepiolite, technical grade low-viscosity carboxymethylcellulose (CMC-LVT), technical grade high-viscosity carboxymethylcellulose (CMC-HVT), and starch. ISO 135

41493,IS,,ISO 13501:2005,Petroleum and natural gas industries — Drilling fluids — Processing systems evaluation,Industries du pétrole et du gaz naturel — Fluides de forage — Évaluation des systèmes de traitement,2005-11-25,1,['75.180.10'],ISO/TC 67/SC 3,9599,,[55304],"['en','fr']",51,<p>ISO 13501:2005 provides a standard procedure for assessing and modifying performance of solids control equipment systems commonly used in the field in petroleum and natural gas drilling fluids processing.</p><p>ISO 13501:2005 is not intended for the comparison of similar types of individual pieces of equipment.</p>

22135,IS,,ISO 13503-1:2003,Petroleum and natural gas industries — Completion fluids and materials — Part 1: Measurement of viscous properties of completion fluids,Industries du pétrole et du gaz naturel — Fluides de complétion et matériaux — Partie 1: Mesurage des propriétés visqueuses des fluides de complétion,2003-08-21,1,['75.100'],ISO/TC 67/SC 3,9599,,[55302],"['en','fr']",20,"<p>ISO 13503-1:2003 provides consistent methodology for determining the viscosity of completion fluids used in the petroleum and natural gas industries. For certain cases, methods are also provided to determine the rheological properties of a fluid.</p>"

43528,IS,Cor,ISO 13503-1:2003/Cor 1:2005,Petroleum and natural gas industries — Completion fluids and materials — Part 1: Measurement of viscous properties of completion fluids — Technical Corrigendum 1,Industries du pétrole et du gaz naturel — Fluides de complétion et matériaux — Partie 1: Mesurage des propriétés visqueuses des fluides de complétion — Rectificatif technique 1,2005-11-11,1,['75.100'],ISO/TC 67/SC 3,9599,,[55302],['fr'],,

36976,IS,,ISO 13503-2:2006,Petroleum and natural gas industries — Completion fluids and materials — Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations,Industries du pétrole et du gaz naturel — Fluides de complétion et matériaux — Partie 2: Mesurage des propriétés des matériaux de soutènement utilisés dans les opérations de fracturation hydraulique et de remplissage de gravier,2006-10-26,1,['75.100'],ISO/TC 67/SC 3,9599,,[86808],"['en','fr','ru']",28,"<p>ISO 13503-2:2006 provides standard testing procedures for evaluating proppants used in hydraulic fracturing and gravel-packing operations.</p><p>'Proppants' mentioned henceforth in ISO 13

44977,IS,Amd,ISO 13503-2:2006/Amd 1:2009,Petroleum and natural gas industries — Completion fluids and materials — Part 2: Measurement of properties of proppants used in hydraulic fracturing and gravel-packing operations — Amendment 1: Addition of Annex B: Proppand specification,Industries du pétrole et du gaz naturel — Fluides de complétion et matériaux — Partie 2: Mesurage des propriétés des matériaux de soutènement utilisés dans les opérations de fracturation hydraulique et de remplissage de gravier — Amendement 1: Ajout de l'Annexe B: Spécifications relatives aux matériaux de soutènement,2009-10-20,1,['75.100'],ISO/TC 67/SC 3,9599,,[86808],"['en','fr']",5,

39154,IS,,ISO 13503-3:2005,Petroleum and natural gas industries — Completion fluids and materials — Part 3: Testing of heavy brines,Industries du pétrole et du gaz naturel — Fluides de complétion et matériaux — Partie 3: Essais de saumures denses,2005-12-07,1,['75.100'],ISO/TC 67/SC 3,9599,,[79583],"['en','fr']",44,"<p>ISO 13503-3:2005 covers the physical properties, potential contaminants and test procedures for heavy brine fluids manufactured for use in oil and gas well drilling, completion and workover fluids.</p><p>ISO 13503-3:2005 provides methods for assessing the performance and physical characteristics of heavy brines for use in field operations. It includes procedures for evaluating

63839,IS,,ISO 13506-1:2017,Protective clothing against heat and flame — Part 1: Test method for complete garments — Measurement of transferred energy using an instrumented manikin,Vêtements de protection contre la chaleur et les flammes — Partie 1: Méthode d'essai pour vêtements complets — Mesurage de l'énergie transférée à l'aide d'un mannequin instrumenté,2017-07-14,1,['13.340.10'],ISO/TC 94/SC 13,9599,[41154],[75863],"['en','fr']",47,"<p>ISO 13506-1:2017 specifies the overall requirements, equipment and calculation methods to provide results that can be used for evaluating the performance of complete garments or protective clothing ensembles exposed to short duration flame engulfment.</p>

63840,IS,,ISO 13506-2:2017,Protective clothing against heat and flame — Part 2: Skin burn injury prediction — Calculation requirements and test cases,Vêtements de protection contre la chaleur et les flammes — Partie 2: Prédiction de blessure par brûlure de la peau — Exigences de calculs et cas d'essai,2017-07-14,1,['13.340.10'],ISO/TC 94/SC 13,9599,[41154],[75864],['en'],18,"<p>ISO 13506-2:2017 provides technical details for calculating predicted burn injury to human skin when its surface is subject to a varying heat flux, such as may occur due to energy transmitted through and by a garment or protective clothing ensemble exposed to flames. A series of test cases are provided against which t

41154,IS,,ISO 13506:2008,Protective clothing against heat and flame — Test method for complete garments — Prediction of burn injury using an instrumented manikin,Vêtements de protection contre la chaleur et la flamme — Méthode d'essai pour vêtements complets — Estimation de la probabilité de brûlure à l'aide d'un mannequin instrumenté,2008-04-15,1,['13.340.10'],ISO/TC 94/SC 13,9599,,"[63839,63840,55841]","['en','fr']",26,"<p>ISO 13506:2008 provides the general principles of a test method for evaluating the performance of complete garments or protective clothing ensembles in a flash fire or other short duration exposures. This test method characterizes the thermal protection provided by garme

53972,IS,,ISO 13517:2013,Metallic powders — Determination of flowrate by means of a calibrated funnel (Gustavsson flowmeter),Poudres métalliques — Détermination du temps d'écoulement au moyen d'un entonnoir calibré (cône d'écoulement de Gustavsson),2013-05-02,1,['77.160'],ISO/TC 119/SC 2,9599,,[77185],"['en','fr']",6,"<p>ISO 13517:2013 specifies a method for determining the flow rate of metallic powders, including powders for hardmetals and mixes of metallic powders and organic additives such as lubricants, by means of a calibrated funnel (Gustavsson flowmeter).</p><p>The method is applicable only to powders which flow freely through the specified test orifice.</p>"

5911,IS,,ISO 1352:1977,Steel — Torsional stress fatigue testing,Acier — Essais de fatigue par contrainte de torsion,1977-12-01,1,['77.040.10'],ISO/TC 164,9599,,[42814],"['en','fr']",4,"<p>The tests are carried out at room temperature, in air, by applying to the test piece a pure couple about its longitudinal axid. Test piece diameters are between 5 mm and 12,5 mm. The proparation, form and testing of test pieces of circular cross-section are specified. Does not specify component testing and high strain torsional fatigue tests, which lead to failure in a few thousand cycles.</p>"

42814,IS,,ISO 1352:2011,Metallic materials — Torque-controlled fatigue testing,Matériaux métalliques — Essais de fatigue par couple de torsion commandé,2011-04-12,2,['77.040.10'],ISO/TC 164/SC 4,9599,[5911],[79576],"['en','ru']",23,"<p>ISO 1352:2011 specifies the conditions for performing torsional, constant-amplitude, nominally elastic stress fatigue tests on metallic specimens without deliberately introducing stress concentrations. The tests are carried out at ambient temperature (ideally at between 10 °C and 35 °C) in air by applying a pure couple to the specimen about its longitudinal axis. </p><p>While the form, preparation and testing of specimens of circular cross-section and tubular

20837,IS,,ISO 13520:2002,Determination of ferrite content in austenitic stainless steel castings,Détermination de la teneur en ferrite dans les pièces moulées en acier inoxydable austénitique,2002-10-03,1,['77.140.80'],ISO/TC 17/SC 11,9599,,[59273],"['en','fr']",9,"<p>In ISO 13520 procedures are covered for estimating ferrite content in certain grades of austenitic iron-chromium-nickel alloy castings that have compositions balanced to create the formation of ferrite as a second phase in amounts controlled within specified limits. Methods are described for estimating ferrite content by chemical, magnetic and metallographic means.</p>"

59273,IS,,ISO 13520:2015,Determination of ferrite content in austenitic stainless steel castings,Détermination du taux de ferrite des pièces moulées en acier inoxydable austénitique,2015-10-01,2,['77.140.80'],ISO/TC 17/SC 11,9599,[20837],[84907],"['en','fr']",9,"<p>ISO 13520:2015 specifies procedures which are covered for estimating ferrite content in certain grades of austenitic iron-chromium-nickel alloy castings that have compositions balanced to create the formation of ferrite as a second phase in amounts controlled within specified limits. Methods are described for estimating ferrite content by chemical, magnetic and metallographic means.</p>"

20836,IS,,ISO 13521:1999,Austenitic manganese steel castings,Pièces moulées en acier austénitique au manganèse,1999-12-16,1,['77.140.80'],ISO/TC 17/SC 11,9599,,[59274],"['en','fr']",3,

59274,IS,,ISO 13521:2015,Austenitic manganese steel castings,Pièces moulées en acier austénitique au manganèse,2015-10-01,2,['77.140.80'],ISO/TC 17/SC 11,9599,[20836],[84908],['en'],4,<p>ISO 13521:2015 specifies austenitic manganese cast steels for wear-resistant service. The grades covered by this International Standard will experience maximum service life in applications where the surface of the casting is subject to impact.</p>

35664,IS,,ISO 13528:2005,Statistical methods for use in proficiency testing by interlaboratory comparisons,Méthodes statistiques utilisées dans les essais d'aptitude par comparaisons interlaboratoires,2005-09-15,1,['03.120.30'],ISO/TC 69/SC 6,9599,,[56125],"['en','fr']",66,"<p>ISO 13528:2005 complements ISO Guide 43 (all parts) by providing detailed descriptions of sound statistical methods for organizers to use to analyse the data obtained from proficiency testing schemes, and by giving recommendations on their use in practice by participants in such schemes and by accreditation bodies.</p><p>ISO 13528:2005 can be applied to demonstrate that the measurement results obtained by laboratories

56125,IS,,ISO 13528:2015,Statistical methods for use in proficiency testing by interlaboratory comparison,Méthodes statistiques utilisées dans les essais d'aptitude par comparaison interlaboratoires,2015-07-28,2,['03.120.30'],ISO/TC 69/SC 6,9599,[35664],[78879],"['en','fr']",89,"<p>ISO 13528:2015 provides detailed descriptions of statistical methods for proficiency testing providers to use to design proficiency testing schemes and to analyse the data obtained from those schemes. It provides recommendations on the interpretation of proficiency testing data by participants in such schemes and by accreditation bodies.</p><p>The procedures in ISO 13528:2015 can be applied to demonstrate that the

22178,IS,,ISO 13534:2000,"Petroleum and natural gas industries — Drilling and production equipment — Inspection, maintenance, repair and remanufacture of hoisting equipment","Industries du pétrole et du gaz naturel — Équipement de forage et de production — Vérification, maintenance, réparation et fabrication à partir de matériaux recyclés du matériel de levage",2000-11-30,1,['75.180.10'],ISO/TC 67/SC 4,9599,,"[72242,41929,61983]",['en'],12,"<p>La présente Norme internationale donne des lignes directrices et établit les exigences relatives au contrôle, à la maintenance, à la réparation et au reconditionnement des éléments des équipements de levage afin de maintenir ce type d'équipement en éta

22180,IS,,ISO 13536:1995,"Soil quality — Determination of the potential cation exchange capacity and exchangeable cations using barium chloride solution buffered at pH = 8,1","Qualité du sol — Détermination de la capacité d'échange cationique potentielle et des teneurs en cations échangeables en utilisant une solution tampon de chlorure de baryum à pH = 8,1",1995-06-01,1,['13.080.10'],ISO/TC 190/SC 3,9599,,[85886],"['en','fr']",7,"<p>Specifies a method for the determination of the potential cation exchange capacity (CEC) of soil buffered at pH = 8,1 and of the determination of the content of exchangeable sodium, potassium, calcium and magnesium in soil. Applicable to all types of air-dried s

53987,IS,,ISO 13541:2010,Space data and information transfer systems — Attitude data messages,Systèmes de transfert des informations et données spatiales — Messages de données d'attitude,2010-09-10,1,['49.140'],ISO/TC 20/SC 13,9599,,[74559],['en'],54,"<p>ISO 13541:2010 specifies two standard message formats for use in transferring spacecraft attitude information between space agencies: the attitude parameter message (APM) and the attitude ephemeris message (AEM). Such exchanges are used for: preflight planning for tracking or attitude estimation support; scheduling attitude and data processing support; carrying out attitude operations; performing attitude comparisons; carrying out attitude p

22185,IS,,ISO 13542:1995,Paper and board — Specification for internal diameters of cores for reels,Papier et carton — Spécification des diamètres intérieurs des mandrins pour bobines,1995-04-27,1,['85.060'],ISO/TC 6,9599,,[36633],"['en','fr']",1,<p>Gives the internal diameters and tolerances for cores recommended for general use with reels of paper and board in international trade.</p>

21522,IS,,ISO 13543:1996,"Copper, lead and zinc sulfide concentrates — Determination of mass of contained metal in a lot","Concentrés sulfurés de cuivre, de plomb et de zinc — Détermination de la masse de métal contenu dans un lot",1996-06-20,1,['73.060.99'],ISO/TC 183,9599,,[63363],['en'],5,

5913,IS,,ISO 1355:1989,"Metallic materials — Hardness test — Calibration of standardized blocks to be used for Rockwell superficial hardness testing machines (scales 15N, 30N, 45N, 15T, 30T and 45T)","Matériaux métalliques — Essai de dureté — Étalonnage des blocs de référence à utiliser pour les machines d'essai de dureté superficielle Rockwell (échelles 15N, 30N, 45N, 15T, 30T et 45T)",1989-11-09,1,['23.040.10'],ISO/TC 164/SC 3,9599,,[26049],"['en','fr']",4,

22199,IS,,ISO 13553:1994,Textile machinery and accessories — Weaver's beams — Specification for connections for automation of beam changing,Matériel pour l'industrie textile — Ensouples de tissage — Caractéristiques dimensionnelles de raccordement pour changement automatisé des ensouples,1994-09-29,1,['59.120.20'],ISO/TC 72/SC 3,9599,,[43666],"['en','fr']",2,<p>Provides specifications for the connections of weaver's beams for the purposes of automation of beam changing. This permits the beams on different weaving machines to be changed in a uniform manner.</p>

29057,IS,,ISO 13562-2:2001,Industrial variable-reach trucks — Part 2: Additional stability tests for trucks handling freight containers of 6 m length and above,Chariots de manutention à portée variable — Partie 2: Essais de stabilité supplémentaires pour les chariots manutentionnant des conteneurs de fret de 6 m de long et plus,2001-01-25,1,['53.060'],ISO/TC 110/SC 2,9599,,[59941],"['en','fr']",12,

22277,IS,,ISO 13563-1:2001,Single side loading fork-lift trucks — Part 1: Stability tests,Chariots élévateurs à fourche à chargement latéral sur un côté — Partie 1: Essais de stabilité,2001-03-15,1,['53.060'],ISO/TC 110/SC 2,9599,,[60406],"['en','fr']",11,

22280,IS,,ISO 13565-2:1996,Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 2: Height characterization using the linear material ratio curve,Spécification géométrique des produits (GPS) — État de surface: Méthode du profil; surfaces ayant des propriétés fonctionnelles différentes suivant les niveaux — Partie 2: Caractérisation des hauteurs par la courbe de taux de longueur portante,1996-12-05,1,['17.040.20'],ISO/TC 213,9599,,[72226],"['en','fr']",6,<p>Contains the evaluation process for determining parameters from the linear representation of the material ratio curve which describes the increase of the materia

29879,IS,Cor,ISO 13565-2:1996/Cor 1:1998,Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 2: Height characterization using the linear material ratio curve — Technical Corrigendum 1,Spécification géométrique des produits (GPS) — État de surface: Méthode du profil; surfaces ayant des propriétés fonctionnelles différentes suivant les niveaux — Partie 2: Caractérisation des hauteurs par la courbe de taux de longueur portante — Rectificatif technique 1,1998-06-04,1,['17.040.20'],ISO/TC 213,9599,,[72226],"['en','fr']",1,

26280,IS,,ISO 13565-3:1998,Geometrical Product Specifications (GPS) — Surface texture: Profile method; Surfaces having stratified functional properties — Part 3: Height characterization using the material probability curve,Spécification géométrique des produits (GPS) — État de surface: Méthode du profil; surfaces ayant des propriétés fonctionnelles différentes suivant les niveaux — Partie 3: Caractérisation des hauteurs par la courbe de probabilité de matière,1998-12-03,1,['17.040.20'],ISO/TC 213,9599,,[72226],"['en','fr']",20,

22281,IS,,ISO 13567-1:1998,Technical product documentation — Organization and naming of layers for CAD — Part 1: Overview and principles,Documentation technique de produits — Organisation et dénomination des couches de CAO — Partie 1: Vue d'ensemble et principes,1998-02-26,1,"['35.240.10','01.110']",ISO/TC 10/SC 8,9599,,[70181],"['en','fr']",3,

26766,IS,,ISO 13567-2:1998,"Technical product documentation — Organization and naming of layers for CAD — Part 2: Concepts, format and codes used in construction documentation","Documentation technique de produits — Organisation et dénomination des couches de CAO — Partie 2: Concepts, format et codes utilisés dans la documentation pour la construction",1998-03-12,1,"['35.240.10','01.110']",ISO/TC 10/SC 8,9599,,[70182],"['en','fr']",10,

42967,IS,,ISO 13571:2007,Life-threatening components of fire — Guidelines for the estimation of time available for escape using fire data,"Composants dangereux du feu — Lignes directrices pour l'estimation du temps disponible pour l'évacuation, utilisant les caractéristiques du feu",2007-06-15,1,['13.220.01'],ISO/TC 92/SC 3,9599,[37003],[56172],"['en','ru']",20,"<p>ISO 13571:2007 is only one of many tools available for use in fire safety engineering. It is intended to be used in conjunction with models for analysis of the initiation and development of fire, fire spread, smoke formation and movement, chemical species generation, transport and decay and people movement, as well as fire detecti

54032,IS,,ISO 13577-1:2012,Industrial furnaces and associated processing equipment — Safety — Part 1: General requirements,Fours industriels et équipements associés — Sécurité — Partie 1: Exigences générales,2012-06-01,1,"['13.100','25.180.01']",ISO/TC 244,9599,,[68019],['en'],45,"<p>ISO 13577-1:2012 specifies the general safety requirements common to industrial furnaces and associated processing equipment (TPE). It details significant hazards associated with TPE, and specifies the appropriate preventive measures for reduction or elimination of these hazards.</p><p>ISO 13577-1:2012 gives general principles and general safety requirements for the reduction of risks associated with TPE.</p><p>

54033,IS,,ISO 13577-2:2014,Industrial furnaces and associated processing equipment — Safety — Part 2: Combustion and fuel handling systems,Fours industriels et équipements associés — Sécurité — Partie 2: Équipement de combustion et de manutention des combustibles,2014-09-08,1,"['13.100','25.180.01']",ISO/TC 244,9599,,[80533],['en'],95,"<p>ISO 13577-2:2014 specifies the safety requirements for combustion and fuel handling systems that are part of industrial furnaces and associated processing equipment (TPE). It deals with significant hazards, hazardous situations and events relevant to combustion and fuel handling systems, when used as intended and under the conditions foreseen by the manufac

57989,IS,,ISO 13577-4:2014,Industrial furnace and associated processing equipment — Safety — Part 4: Protective systems,Fours industriels et équipements associés — Sécurité — Partie 4: Systèmes de protection,2014-08-22,1,"['13.100','25.180.01']",ISO/TC 244,9599,,[80534],['en'],71,<p>ISO 13577-4:2014 specifies the requirements for protective systems used in industrial furnaces and associated processing equipment (TPE). The functional requirements to which the protective systems apply are specified in the other parts of ISO 13577.</p>

22043,IS,,ISO 13583-1:2000,Centrifugally cast steel and alloy products — Part 1: General testing and tolerances,Produits en acier et alliages moulés par centrifugation — Partie 1: Conditions générales d'essais et tolérances,2000-12-07,1,['77.140.80'],ISO/TC 17/SC 11,9599,,[59275],"['en','fr']",7,

59275,IS,,ISO 13583-1:2015,Centrifugally cast steel and alloy products — Part 1: General testing and tolerances,Produits en acier et alliages moulés par centrifugation — Partie 1: Conditions générales d'essais et tolérances,2015-09-08,2,['77.140.80'],ISO/TC 17/SC 11,9599,[22043],[84507],['en'],7,<p>ISO 13583-1:2015 specifies the requirements for horizontal and vertical centrifugally cast steel and alloy products to be used in the following applications:</p><p>a) heat resisting;</p><p>b) corrosion resisting;</p><p>c) general engineering.</p>

27977,IS,,ISO 13583-2:2003,Centrifugally cast steel and alloy products — Part 2: Heat resistant materials,Produits en acier et alliages moulés par centrifugation — Partie 2: Aciers moulés réfractaires,2003-09-08,1,['77.140.80'],ISO/TC 17/SC 11,9599,,[59276],['en'],7,<p>ISO 13583-2:2003 specifies cast steel and alloy grades for elevated temperature service pieces manufactured by centrifugal casting.</p>

59276,IS,,ISO 13583-2:2015,Centrifugally cast steel and alloy products — Part 2: Heat-resistant materials,Produits en acier et alliages moulés par centrifugation — Partie 2: Aciers moulés réfractaires,2015-09-08,2,['77.140.80'],ISO/TC 17/SC 11,9599,[27977],[84508],['en'],9,<p>ISO 13583-2:2015 specifies cast steel and nickel alloy grades for elevated temperature service products manufactured by centrifugal casting.</p>

22332,IS,,ISO 13584-42:1998,Industrial automation systems and integration — Parts library — Part 42: Description methodology: Methodology for structuring part families,Systèmes d'automatisation industrielle et intégration — Bibliothèque de composants — Partie 42: Méthodologie descriptive: Méthodologie appliquée à la structuration des familles de pièces,1998-07-16,1,['25.040.40'],ISO/TC 184/SC 4,9599,,[43423],['en'],132,

37889,IS,Cor,ISO 13584-42:1998/Cor 1:2003,Industrial automation systems and integration — Parts library — Part 42: Description methodology: Methodology for structuring part families — Technical Corrigendum 1,Systèmes d'automatisation industrielle et intégration — Bibliothèque de composants — Partie 42: Méthodologie descriptive: Méthodologie appliquée à la structuration des familles de pièces — Rectificatif technique 1,2003-01-09,1,['25.040.40'],ISO/TC 184/SC 4,9599,,[43423],['en'],22,

54051,IS,,ISO 13585:2012,Brazing — Qualification test of brazers and brazing operators,Brasage fort — Essais de qualification des braseurs et des opérateurs braseurs en brasage fort,2012-06-07,1,['25.160.01'],ISO/TC 44/SC 11,9599,,"[74305,75561]","['en','fr']",17,"<p>ISO 13585:2012 specifies basic requirements for the qualification testing of brazers and brazing operators providing conditions for brazing, testing, examination, acceptance criteria and range of qualification for certificates.</p>"

22321,IS,,ISO 13586:2000,Plastics — Determination of fracture toughness (GIC and KIC) — Linear elastic fracture mechanics (LEFM) approach,Plastiques — Détermination de la ténacité à la rupture (GIC et KIC) — Application de la mécanique linéaire élastique de la rupture (LEFM),2000-03-09,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[67721],"['en','fr']",16,

33807,IS,Amd,ISO 13586:2000/Amd 1:2003,Plastics — Determination of fracture toughness (GIC and KIC) — Linear elastic fracture mechanics (LEFM) approach — Amendment 1: Guidelines for the testing of injection-moulded plastics containing discontinuous reinforcing fibres,Plastiques — Détermination de la ténacité à la rupture (GIC et KIC) — Application de la mécanique linéaire élastique de la rupture (LEFM) — Amendement 1: Lignes directrices relatives à l'essai des matériaux plastiques moulés par injection contenant des fibres de renfort discontinues,2003-06-18,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[67721],"['en','fr']",6,

54054,IS,,ISO 13588:2012,Non-destructive testing of welds — Ultrasonic testing — Use of automated phased array technology,Contrôle non destructif des assemblages soudés — Contrôle par ultrasons — Utilisation de la technique multi-éléments automatisés,2012-09-28,1,['25.160.40'],ISO/TC 44/SC 5,9599,,[72747],"['en','fr']",17,"<p>ISO 13588:2012 specifies the application of the phased array technology for the semi- or fully automated ultrasonic testing of fusion-welded joints in metallic materials of minimum thickness 6 mm. It applies to full penetration welded joints of simple geometry in plates, pipes, and vessels, where both the weld and parent material are low-alloyed carbon steel.</p><p>Wher

22348,IS,,ISO 13590:1997,Small craft — Personal watercraft — Construction and system installation requirements,Navires de plaisance — Motos aquatiques — Exigences de construction et d'installation des systèmes,1997-09-18,1,['47.080'],ISO/TC 188,9599,,[35253],"['en','fr']",16,

35253,IS,,ISO 13590:2003,Small craft — Personal watercraft — Construction and system installation requirements,Petits navires — Motos aquatiques — Exigences de construction et d'installation des systèmes,2003-12-04,2,['47.080'],ISO/TC 188,9599,[22348],[76684],"['en','fr']",21,"<p>ISO 13590:2003 applies to personal watercraft, for the construction and installation of builder's plate, permanently installed petrol fuel systems, electrical systems, steering systems, ventilation, hull structure and floatation, and requirements for stability, freeboard and owner's manual.</p>"

3949,IS,,ISO 136:1972,Steel — Simple torsion testing of wire,Acier — Essai de torsion simple des fils,1972-12-01,1,"['77.140.65','77.040.10']",ISO/TC 164/SC 2,9599,,[14694],"['en','fr']",2,

40784,IS,,ISO 13606-1:2008,Health informatics — Electronic health record communication — Part 1: Reference model,Informatique de santé — Communication du dossier de santé informatisé — Partie 1: Modèle de référence,2008-02-07,1,['35.240.80'],ISO/TC 215,9599,,[67868],"['en','fr']",83,"<p>ISO 13606-1:2008 specifies the communication of part or all of the electronic health record (EHR) of a single identified subject of care between EHR systems, or between EHR systems and a centralized EHR data repository.</p><p>It may also be used for EHR communication between an EHR system or repository and clinical applications or middleware components (such as decision support components) that need to access

50119,IS,,ISO 13606-2:2008,Health informatics — Electronic health record communication — Part 2: Archetype interchange specification,Informatique de santé — Communication du dossier de santé informatisé — Partie 2: Spécification d'échange d'archétype,2008-11-25,1,['35.240.80'],ISO/TC 215,9599,,[62305],['en'],124,"<p>ISO 13606-2:2008 specifies the information architecture required for interoperable communications between systems and services that need or provide EHR data. ISO 13606-2:2008 is not intended to specify the internal architecture or database design of such systems.</p><p>The subject of the record or record extract to be communicated is an individual person, and the scope of the com

50120,IS,,ISO 13606-3:2009,Health informatics — Electronic health record communication — Part 3: Reference archetypes and term lists,Informatique de santé — Communication du dossier de santé informatisé — Partie 3: Archétypes de référence et listes de termes,2009-01-14,1,['35.240.80'],ISO/TC 215,9599,,[62303],['en'],46,"<p>ISO 13606-3:2009 is for the communication of part or all of the electronic health record (EHR) of a single identified subject of care between EHR systems, or between EHR systems and a centralized EHR data repository. It may also be used for EHR communication between an EHR system or repository and clinical applications or middleware components (such as decision support co

50122,IS,,ISO 13606-5:2010,Health informatics — Electronic health record communication — Part 5: Interface specification,Informatique de santé — Communication du dossier de santé informatisé — Partie 5: Spécification d'interfaces,2010-02-23,1,['35.240.80'],ISO/TC 215,9599,,[62304],"['en','fr']",15,"<p>ISO 13606-5:2010 specifies the information architecture required for interoperable communications between systems and services that need or provide EHR data.</p><p>The subject of the record or record extract to be communicated is an individual person, and the scope of the communication is predominantly with respect to that person's care.</p><p>ISO 13606-5:2010 defines a set of interfaces to req

54080,IS,,ISO 13609:2014,Wood-based panels — Plywood — Blockboards and battenboards,Panneaux à base de bois — Contreplaqués — Panneaux lattés avec lattes étroites et avec lattes larges,2014-02-03,1,['79.060.99'],ISO/TC 89/SC 3,9599,,[80857],['en'],6,"<p>ISO 13609:2014 establishes requirements for the specifications of blockboards and battenboards for general use, in dry, tropic dry/humid, and high-humid/exterior conditions. It includes requirements of materials, lay-up, physical and mechanical properties, bonding quality, formaldehyde release, conformity verification, and marking.</p><p>The values listed in ISO 13609:2014 relate to product properties, but they are not characteristic values t

5914,IS,,ISO 1361:1983,Light gauge metal containers — Open-top cans — Round cans — Internal diameters,Récipients métalliques légers — Boîtes serties — Boîtes rondes — Diamètres intérieurs,1983-11-01,3,['55.120'],ISO/TC 52,9599,,[22786],"['en','fr']",2,

54082,IS,,ISO 13611:2014,Interpreting — Guidelines for community interpreting,Interprétation — Lignes directrices pour l'interprétation en milieu social,2014-11-26,1,['01.020'],ISO/TC 37/SC 5,9599,,[82387],"['en','fr']",15,"<p>ISO 13611:2014 establishes criteria and recommendations for community interpreting during oral and signed communication that enables access to services for people who have limited proficiency in the language of such services. Community interpreting occurs in a wide variety of private and public settings and supports equal access to community and/or public services.</p><p>ISO 13611:2014 addresses community interpreting as a profession, not as an informal practice such a

41031,IS,,ISO 13616-1:2007,Financial services - International bank account number (IBAN) — Part 1: Structure of the IBAN,Services financiers — Numéro de compte bancaire international (IBAN) — Partie 1: Structure de l'IBAN,2007-02-23,1,['03.060'],ISO/TC 68/SC 8,9599,[38213],"[73994,81090]",['en'],8,"<p>ISO 13616-1:2007 specifies the elements of an international bank account number (IBAN) used to facilitate the processing of data internationally in data interchange, in financial environments as well as within and between other industries. The IBAN is designed for automated processing, but can also be used conveniently in other media interchange when appropriate (e.g. paper document exchange, e

21228,IS,,ISO 13616:1997,Banking and related financial services — International Bank Account Number (IBAN),Banque et services financiers connexes — Numéro de compte bancaire international (IBAN),1997-09-25,1,['03.060'],ISO/TC 68,9599,,[38213],['en'],5,

41032,IS,,ISO 13616-2:2007,Financial services - International bank account number (IBAN) — Part 2: Role and responsibilities of the Registration Authority,Services financiers — Numéro de compte bancaire international (IBAN) — Partie 2: Rôle et responsabilités de l'organisation d'enregistrement,2007-02-23,1,['03.060'],ISO/TC 68/SC 8,9599,[38213],[81091],['en'],6,"<p>ISO 13616-2:2007 describes the Registration Authority (RA) responsible for the registry of IBAN formats that are compliant with ISO 13616-1, the procedures for registering ISO 13616-compliant IBAN formats and the structure of the registry.</p>"

38213,IS,,ISO 13616:2003,Banking and related financial services — International bank account number (IBAN),Banque et services financiers connexes — Numéro de compte bancaire international (IBAN),2003-07-24,2,['03.060'],ISO/TC 68,9599,[21228],"[39852,41031,41032]",['en'],7,"<p>ISO 13616:2003 specifies the elements of an international bank account number (IBAN), used to facilitate the processing of data in data interchange internationally -- in financial environments as well as within and between other industries. The IBAN is designed for automated processing, but can also be conveniently used in other media interchange when appropriate (paper document exchange, etc.). ISO 13616 does not speci

22400,IS,,ISO 13617:1995,Shipbuilding — Shipboard incinerators — Requirements,Construction navale — Incinérateurs de bord pour navires — Exigences,1995-08-17,1,"['13.030.40','47.020.99']",ISO/TC 8/SC 3,9599,,[31725],"['en','fr']",20,<p>Lays down the requirements for shipboard incinerators. The requirements originate from the IMO resolution MEPC.59(33).</p>

31725,IS,,ISO 13617:2001,Ships and marine technology — Shipboard incinerators — Requirements,Navires et technologie maritime — Incinérateurs de bord pour navires — Exigences,2001-11-15,2,"['13.030.40','47.020.99']",ISO/TC 8/SC 2,9599,[22400],[66932],['en'],20,