Withdrawn and superseded ISO standards — page 35 of 246

21706,IS,,ISO 13320-1:1999,Particle size analysis — Laser diffraction methods — Part 1: General principles,Analyse granulométrique — Méthodes par diffraction laser — Partie 1: Principes généraux,1999-11-11,1,['19.120'],ISO/TC 24/SC 4,9599,,[44929],"['en','fr']",34,

44929,IS,,ISO 13320:2009,Particle size analysis — Laser diffraction methods,Analyse granulométrique — Méthodes par diffraction laser,2009-09-18,1,['19.120'],ISO/TC 24/SC 4,9599,[21706],[69111],['en'],51,"<p>ISO 13320:2009 provides guidance on instrument qualification and size distribution measurement of particles in many two-phase systems (e.g. powders, sprays, aerosols, suspensions, emulsions and gas bubbles in liquids) through the analysis of their light-scattering properties. It does not address the specific requirements of particle size measurement of specific materials.</p><p>ISO 13320:2009 is applicable to particle sizes ranging from approximately 0,1 µm to 3 mm. With special instrume

21707,IS,,ISO 13321:1996,Particle size analysis — Photon correlation spectroscopy,Analyse granulométrique — Spectroscopie par corrélation de photons,1996-07-11,1,['19.120'],ISO/TC 24/SC 4,9599,,[65410],"['en','fr']",20,

38664,IS,,ISO 13322-1:2004,Particle size analysis — Image analysis methods — Part 1: Static image analysis methods,Analyse granulométrique — Méthodes par analyse d'images — Partie 1: Méthodes par analyse d'images statiques,2004-12-02,1,['19.120'],ISO/TC 24/SC 4,9599,,[51257],['en'],39,"<p>ISO 13322:2004 is applicable to the analysis of images for the purpose of determining particle size distributions. The particles are appropriately dispersed and fixed on an optical or electron microscope sample stage such as glass slides, stubs, filters, etc. Image analysis can recover particle images directly from microscopes or from photomicrographs.</p><p>Even though automation of the analysis is possibl

38665,IS,,ISO 13322-2:2006,Particle size analysis — Image analysis methods — Part 2: Dynamic image analysis methods,Analyse granulométrique — Méthodes par analyse d'images — Partie 2: Méthodes par analyse d'images dynamiques,2006-10-25,1,['19.120'],ISO/TC 24/SC 4,9599,,[72566],['en'],24,"<p>ISO 13322-2:2006 describes methods for controlling the position of moving particles in a liquid or gas and on a conveyor, as well as the image capture and image analysis of the particles. These methods are used to measure the particle sizes and their distributions, the particles being appropriately dispersed in the liquid or gas medium or on the conveyor. The practical limitations of the derived particle

21709,IS,,ISO 13323-1:2000,Determination of particle size distribution — Single-particle light interaction methods — Part 1: Light interaction considerations,Détermination de la distribution granulométrique — Méthodes d'interaction lumineuse de particules uniques — Partie 1: Considérations relatives à l'interaction lumineuse,2000-11-02,1,['19.120'],ISO/TC 24/SC 4,9599,,"[40275,40276,40274]",['en'],15,

35528,IS,,ISO 13325:2003,Tyres — Coast-by methods for measurement of tyre-to-road sound emission,Pneumatiques — Méthodes en roue libre pour le mesurage de l'émission acoustique issue du contact pneumatique/chaussée,2003-01-22,1,"['17.140.30','83.160.10']",ISO/TC 31,9599,,[71034],"['en','fr']",23,"<p>ISO 13325:2003 specifies methods for measuring tyre-road sound emissions from tyres fitted on a motor vehicle or towed trailer under coast-by conditions -- i.e. when the vehicle or trailer is in free-rolling, non-powered operation, with transmission in the neutral position and the engine as well as all auxiliary systems not necessary for safe driving switched off.</p>"

21716,IS,,ISO 13327:1998,Motorcycle tyres — Method of measuring rolling resistance,Pneumatiques pour motocycles — Méthode de mesure de la résistance au roulement,1998-09-03,1,['83.160.10'],ISO/TC 31/SC 10,9599,,[33328],"['en','fr']",17,

21729,IS,,ISO 13332:2000,Reciprocating internal combustion engines — Test code for the measurement of structure-borne noise emitted from high-speed and medium-speed reciprocating internal combustion engines measured at the engine feet,"Moteurs alternatifs à combustion interne — Code d'essai pour le mesurage du bruit solidien émis par les moteurs alternatifs à combustion interne à vitesse élevée et à vitesse moyenne, mesuré aux pieds du moteur",2000-11-23,1,"['27.020','17.140.20']",ISO/TC 70,9599,,[88177],"['en','fr']",13,

21734,IS,,ISO 13337:1997,"Spring-type straight pins — Slotted, light duty","Goupilles cylindriques creuses, dites goupilles élastiques — Série mince",1997-11-06,1,['21.060.50'],ISO/TC 2,9599,,[40657],"['en','fr']",6,

21740,IS,,ISO 13338:1995,Determination of tissue corrosiveness of a gas or gas mixture,Détermination de la corrosivité des gaz ou mélanges de gaz sur les tissus,1995-11-09,1,['71.100.20'],ISO/TC 58/SC 2,9599,,[65112],"['en','fr']",10,<p>Gives a complete list of the corrosiveness for pure gases and a calculation method relating to the corrosiveness of gas mixtures which is applicable in the absence of experimental data to each of their components.</p>

65112,IS,,ISO 13338:2017,Gas cylinders — Gases and gas mixtures — Determination of tissue corrosiveness for the selection of cylinder valve outlets,Bouteilles à gaz — Gaz et mélanges de gaz — Détermination de la corrosivité sur les tissus pour le choix des raccords de sortie de robinets,2017-06-01,2,['71.100.20'],ISO/TC 58/SC 2,9599,[21740],[81926],"['en','fr']",8,"<p>ISO 13338:2017 provides:</p><p>- for pure gases and some liquids, a complete list indicating their corrosiveness;</p><p>- for gas mixtures, a calculation method, in the absence of experimental data, relating to the corrosiveness of each of their components;</p><p>in order to determine the corrosiveness of gases and ga

21742,IS,,ISO 13340:2001,Transportable gas cylinders — Cylinders valves for non-refillable cylinders — Specification and prototype testing,Bouteilles à gaz transportables — Robinets pour bouteilles non rechargeables — Spécifications et essais de prototype,2001-04-05,1,['23.020.35'],ISO/TC 58/SC 2,9599,,[45767],"['en','fr']",8,

21743,IS,,ISO 13341:1997,Transportable gas cylinders — Fitting of valves to gas cylinders,Bouteilles à gaz transportables — Montage des robinets sur les bouteilles à gaz,1997-10-16,1,['23.020.35'],ISO/TC 58/SC 2,9599,,[50503],"['en','fr']",7,

30563,IS,Cor,ISO 13341:1997/Cor 1:1998,Transportable gas cylinders — Fitting of valves to gas cylinders — Technical Corrigendum 1,Bouteilles à gaz transportables — Montage des robinets sur les bouteilles à gaz — Rectificatif technique 1,1998-08-20,1,['23.020.35'],ISO/TC 58/SC 2,9599,,[50503],"['en','fr']",2,

50503,IS,,ISO 13341:2010,Gas cylinders — Fitting of valves to gas cylinders,Bouteilles à gaz — Montage des robinets sur les bouteilles à gaz,2010-09-30,2,['23.020.35'],ISO/TC 58,9599,"[21743,30563]",[85996],"['en','fr']",8,<p>ISO 13341:2010 specifies the procedures to be followed when connecting cylinder valves to gas cylinders. It specifically applies to all valve and cylinder combinations connected with ISO screw threads as specified in ISO 10920 and ISO 11363-1. It defines routines for inspection and preparation prior to valving for both taper and parallel screw threads.</p><p>Torque values are given for steel and aluminium gas cylinders including composite cylinders with steel or alumini

59968,IS,Amd,ISO 13341:2010/Amd 1:2015,Gas cylinders — Fitting of valves to gas cylinders — Amendment 1,Bouteilles à gaz — Montage des robinets sur les bouteilles à gaz — Amendement 1,2015-05-29,2,['23.020.35'],ISO/TC 58,9599,,[85996],"['en','fr']",1,

21617,IS,,ISO 13344:1996,Determination of the lethal toxic potency of fire effluents,Détermination du pouvoir toxique létal des effluents du feu,1996-12-12,1,['13.220.99'],ISO/TC 92/SC 3,9599,,[37850],"['en','fr']",12,"<p>Provides a means for estimating the lethal toxic potency of the fire effluents produced from a material, while exposed to the specific combustion conditions of a laboratory fire model.</p>"

37850,IS,,ISO 13344:2004,Estimation of the lethal toxic potency of fire effluents,Détermination du pouvoir toxique létal des effluents du feu,2004-10-14,2,['13.220.99'],ISO/TC 92/SC 3,9599,[21617],[68029],['en'],14,"<p>ISO 13344:2004 provides a means for estimating the lethal toxic potency of the fire effluents produced from a material while exposed to the specific combustion conditions of a physical fire model. The lethal toxic potency values are specifically related to the fire model selected, the exposure scenario and the material evaluated.</p><p>Lethal toxic potency values associated with 30-min exposures of rats are predicted using calculations which employ combustion atmosphere analyt

34435,IS,,ISO 13347-1:2004,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 1: General overview,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 1: Présentation générale,2004-08-17,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87805],"['en','fr']",34,"<p>ISO 13347:2004 deals with the determination of the acoustic performance of industrial fans. In addition, it may be used to determine the acoustic performance of fans combined with an ancillary device such as a roof cowl or damper or, where the fan is fitted with a silencer, the sound pow

56775,IS,Amd,ISO 13347-1:2004/Amd 1:2010,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 1: General overview — Amendment 1,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 1: Présentation générale — Amendement 1,2010-11-05,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87805],"['en','fr']",1,

44485,IS,Cor,ISO 13347-1:2004/Cor 1:2006,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 1: General overview — Technical Corrigendum 1,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 1: Présentation générale — Rectificatif technique 1,2006-10-19,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87805],"['en','fr']",1,

29752,IS,,ISO 13347-2:2004,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 2: Reverberant room method,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 2: Méthode de la salle réverbérante,2004-08-17,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87806],"['en','fr']",22,"<p>ISO 13347-2:2004 gives a detailed description of reverberant room methods for the determination of fan sound power levels. It is for use under standardized laboratory conditions and recognises that tests in situ are subject to increased uncertainty. These test procedure

44484,IS,Cor,ISO 13347-2:2004/Cor 1:2006,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 2: Reverberant room method — Technical Corrigendum 1,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 2: Méthode de la salle réverbérante — Rectificatif technique 1,2006-10-12,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87806],"['en','fr']",1,

29753,IS,,ISO 13347-3:2004,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 3: Enveloping surface methods,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 3: Méthodes de la surface enveloppante,2004-08-17,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87807],"['en','fr']",22,"<p>ISO 13347-3:2004 applies to industrial fans as defined in ISO 5801 and ISO 13349. It is limited to the determination of airborne sound emission for the specified set-ups. Vibration is not measured, nor is the sensitivity of airborne sound emission to vibration eff

56776,IS,Amd,ISO 13347-3:2004/Amd 1:2010,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 3: Enveloping surface methods — Amendment 1,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 3: Méthodes de la surface enveloppante — Amendement 1,2010-11-05,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87807],"['en','fr']",1,

44121,IS,Cor,ISO 13347-3:2004/Cor 1:2006,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 3: Enveloping surface methods — Technical Corrigendum 1,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 3: Méthodes de la surface enveloppante — Rectificatif technique 1,2006-11-10,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87807],"['en','fr']",4,

29754,IS,,ISO 13347-4:2004,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 4: Sound intensity method,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 4: Méthode de l'intensité acoustique,2004-08-17,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87808],"['en','fr']",25,"<p>ISO 13347-4:2004 applies to industrial fans as defined in ISO 5801 and ISO 13349. It is limited to the determination of airborne sound emission for the specified set-ups. Vibration is not measured, nor is the sensitivity of airborne sound emission to vibration effects d

44483,IS,Cor,ISO 13347-4:2004/Cor 1:2006,Industrial fans — Determination of fan sound power levels under standardized laboratory conditions — Part 4: Sound intensity method — Technical Corrigendum 1,Ventilateurs industriels — Détermination des niveaux de puissance acoustique des ventilateurs dans des conditions de laboratoire normalisées — Partie 4: Méthode de l'intensité acoustique — Rectificatif technique 1,2006-11-01,1,"['23.120','17.140.20']",ISO/TC 117,9599,,[87808],"['en','fr']",2,

39161,IS,,ISO 13348:2006,"Industrial fans — Tolerances, methods of conversion and technical data presentation","Ventilateurs industriels — Tolérances, méthodes de conversion et présentation des données techniques",2006-02-28,1,['23.120'],ISO/TC 117,9599,,[45118],"['en','fr']",53,"<p>ISO 13348:2006 specifies performance tolerances and the technical data presentation of industrial fans of all types. It does not apply for fans designed solely for low-volume air circulation, such as those used for household or similar purposes (ceiling and table fans, extractor fans, etc.). </p><p>ISO 13348:2006 covers the four installation categories defined in ISO 5801:A, free inlet, free outlet; B, free inlet

45118,IS,,ISO 13348:2007,"Industrial fans — Tolerances, methods of conversion and technical data presentation","Ventilateurs industriels — Tolérances, méthodes de conversion et présentation des données techniques",2007-01-15,2,['23.120'],ISO/TC 117,9599,[39161],"[73004,87615]","['en','fr']",53,"<p>ISO 13348:2007 specifies performance tolerances and the technical data presentation of industrial fans of all types. It does not apply for fans designed solely for low-volume air circulation, such as those used for household or similar purposes (ceiling and table fans, extractor fans, etc.). </p><p>ISO 13348:2007 covers the four installation categories defined in ISO 5801: A, free inlet, free outle

21759,IS,,ISO 13349:1999,Industrial fans — Vocabulary and definitions of categories,Ventilateurs industriels — Vocabulaire et définitions des catégories,1999-10-14,1,"['23.120','01.040.23']",ISO/TC 117,9599,,[46450],"['en','fr']",39,

46450,IS,,ISO 13349:2010,Fans — Vocabulary and definitions of categories,Ventilateurs — Vocabulaire et définitions des catégories,2010-06-22,2,"['23.120','01.040.23']",ISO/TC 117,9599,[21759],"[84496,81042]","['en','fr']",43,<p>ISO 13349:2010 defines terms and categories in the field of fans used for all purposes.</p><p>It is not applicable to electrical safety.</p>

21760,IS,,ISO 13350:1999,Industrial fans — Performance testing of jet fans,Ventilateurs industriels — Essai de performance des ventilateurs accélérateurs,1999-10-14,1,['23.120'],ISO/TC 117,9599,,[62033],"['en','fr']",27,

21761,IS,,ISO 13351:1996,Industrial fans — Dimensions,Ventilateurs industriels — Dimensions,1996-06-20,1,['23.120'],ISO/TC 117,9599,,[52816],"['en','fr']",10,

52816,IS,,ISO 13351:2009,Fans — Dimensions,Ventilateurs — Dimensions,2009-11-04,2,['23.120'],ISO/TC 117,9599,"[21761,41116]","[86061,78383]","['en','fr']",13,"<p>ISO 13351:2009 specifies the dimensions of the circular and rectangular flanges of general‑purpose fans, as well as the fan size designations. It is not applicable to cross‑flow fans or to fan appliances used for individual household or similar applications.</p>"

35211,IS,,ISO 13355:2001,"Packaging — Complete, filled transport packages and unit loads — Vertical random vibration test",Emballages — Emballages d'expédition complets et pleins et charges unitaires — Essais de vibration verticale aléatoire,2001-11-15,1,['55.180.40'],ISO/TC 122/SC 3,9599,,[62098],"['en','fr']",5,

21234,IS,,ISO 13356:1997,Implants for surgery — Ceramic materials based on yttria-stabilized tetragonal zirconia (Y-TZP),Implants chirurgicaux — Produits céramiques à base de zircone tétragonale stabilisée à l'oxyde d'yttrium,1997-09-11,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[40166],"['en','fr']",7,

40166,IS,,ISO 13356:2008,Implants for surgery — Ceramic materials based on yttria-stabilized tetragonal zirconia (Y-TZP),Implants chirurgicaux — Produits céramiques à base de zircone tétragonal stabilisé à l'oxyde d'yttrium (Y-TZP),2008-05-19,2,['11.040.40'],ISO/TC 150/SC 1,9599,[21234],[62373],"['en','fr']",13,"<p>ISO 13356:2008 specifies the characteristics of, and corresponding test methods for, a biocompatible and biostable ceramic bone-substitute material based on yttria-stabilized tetragonal zirconia (yttria tetragonal zirconia polycrystal, Y-TZP) for use as material for surgical implants.</p>"

21051,IS,,ISO 13357-1:2002,Petroleum products — Determination of the filterability of lubricating oils — Part 1: Procedure for oils in the presence of water,Produits pétroliers — Détermination de la filtrabilité des huiles lubrifiantes — Partie 1: Méthode pour les huiles en présence d'eau,2002-06-13,1,['75.100'],ISO/TC 28,9599,,[66352],"['en','fr','ru']",9,"<p>This part of ISO 13357 specifies a procedure for the evaluation of the filterability of lubricating oils, particularly those designed for hydraulic applications, in the presence of water. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) may not be compatible w

66352,IS,,ISO 13357-1:2017,Petroleum products — Determination of the filterability of lubricating oils — Part 1: Procedure for oils in the presence of water,Produits pétroliers — Détermination de la filtrabilité des huiles lubrifiantes — Partie 1: Méthode pour les huiles en présence d'eau,2017-05-09,2,['75.100'],ISO/TC 28,9599,[21051],[86969],['en'],12,"<p>ISO 13357-1:2017 specifies a procedure for the evaluation of the filterability of lubricating oils, particularly those designed for hydraulic applications, in the presence of water. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) may not be compatible with the sp

22471,IS,,ISO 13357-2:1998,Petroleum products — Determination of the filterability of lubricating oils — Part 2: Procedure for dry oils,Produits pétroliers — Détermination de la filtrabilité des huiles lubrifiantes — Partie 2: Méthode pour les huiles non polluées par de l'eau,1998-05-28,1,['75.100'],ISO/TC 28,9599,,[42258],"['en','fr']",9,

42258,IS,,ISO 13357-2:2005,Petroleum products — Determination of the filterability of lubricating oils — Part 2: Procedure for dry oils,Produits pétroliers — Détermination de la filtrabilité des huiles lubrifiantes — Partie 2: Méthode pour les huiles non polluées par de l'eau,2005-10-17,2,['75.100'],ISO/TC 28,9599,[22471],[66353],"['en','fr','ru']",10,"<p>This part of ISO 13357:2005 specifies a procedure for the evaluation of the filterability of dry lubricating oils, particularly those designed for hydraulic applications. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) might not be compatible with the specified te

66353,IS,,ISO 13357-2:2017,Petroleum products — Determination of the filterability of lubricating oils — Part 2: Procedure for dry oils,Produits pétroliers — Détermination de la filtrabilité des huiles lubrifiantes — Partie 2: Méthode pour les huiles non polluées par de l'eau,2017-05-09,3,['75.100'],ISO/TC 28,9599,[42258],[86970],['en'],12,"<p>ISO 13357-2:2017 specifies a procedure for the evaluation of the filterability of dry lubricating oils, particularly those designed for hydraulic applications. The procedure only applies to mineral-based oils, since fluids manufactured from other materials (e.g. fire-resistant fluids) might not be compatible with the specified test membranes. The range

2863,IS,,ISO 13359:1998,Measurement of conductive liquid flow in closed conduits — Flanged electromagnetic flowmeters — Overall length,Mesurage du débit des liquides conducteurs dans les conduites fermées — Débitmètres électromagnétiques à brides — Longueur d'installation,1998-07-02,1,['17.120.10'],ISO/TC 30/SC 5,9599,,"[56131,68092]","['en','fr']",4,

34469,IS,,ISO 13363:2004,Rubber and plastics hoses for marine-engine wet-exhaust systems — Specification,Tuyaux d'échappement en caoutchouc et en plastique pour moteurs de bateaux de plaisance — Spécifications,2004-02-24,1,"['83.140.40','47.080']",ISO/TC 45/SC 1,9599,,[63963],['en'],9,"<p>ISO 13363:2004 specifies requirements for three types and two classes of hose. The hoses are intended for use in marine-engine wet-exhaust systems (where the exhaust gases are mixed with the discharge of cooling water). The standard does not apply to outboard-motor/personal water craft.</p><p>The three types are:</p><ol><li>type 1: a softwall hose, made of oil-resistant material, with a synthetic-fabric rei

51190,IS,Cor,ISO 13363:2004/Cor 1:2008,Rubber and plastics hoses for marine-engine wet-exhaust systems — Specification — Technical Corrigendum 1,Tuyaux d'échappement en caoutchouc et en plastique pour moteurs de bateaux de plaisance — Spécifications — Rectificatif technique 1,2008-02-18,1,"['83.140.40','47.080']",ISO/TC 45/SC 1,9599,,[63963],['en'],1,"<p>ISO 13363:2004 specifies requirements for three types and two classes of hose. The hoses are intended for use in marine-engine wet-exhaust systems (where the exhaust gases are mixed with the discharge of cooling water). The standard does not apply to outboard-motor/personal water craft.</p><p>The three types are:</p><ol><li>type 1: a softwal

53718,IS,,ISO 13365:2011,"Leather — Chemical tests — Determination of the preservative (TCMTB, PCMC, OPP, OIT) content in leather by liquid chromatography","Cuir — Essais chimiques — Dosage des agents de conservation (TCMTB, PCMC, OPP, OIT) dans le cuir par chromatographie en phase liquide",2011-01-11,1,['59.140.30'],IULTCS,9599,,"[73699,73700]","['en','fr']",5,<p>ISO 13365:2011 specifies a test method for the determination of the content of the following preservative agents: </p><p>2-(thiocyanomethylthio)-benzothiazole (TCMTB); </p><p>4-chloro-3-methylphenol (PCMC); </p><p>2-phenylphenol (OPP);</p><p>2-octylisothiazol-3(2H)-one (OIT);</p><p>in leather by liquid chromatography. </p><p>Preser

21796,IS,,ISO 13366-1:1997,Milk — Enumeration of somatic cells — Part 1: Microscopic method,Lait — Dénombrement des cellules somatiques — Partie 1: Méthode au microscope,1997-06-12,1,['67.100.10'],ISO/TC 34/SC 5,9599,,[40259],"['en','fr']",6,

21797,IS,,ISO 13366-2:1997,Milk — Enumeration of somatic cells — Part 2: Electronic particle counter method,Lait — Dénombrement des cellules somatiques — Partie 2: Méthode au compteur électronique de particules,1997-06-12,1,['67.100.10'],ISO/TC 34/SC 5,9599,,[40260],"['en','fr']",6,

21798,IS,,ISO 13366-3:1997,Milk — Enumeration of somatic cells — Part 3: Fluoro-opto-electronic method,Lait — Dénombrement des cellules somatiques — Partie 3: Méthode fluoro-opto-électronique,1997-06-12,1,['67.100.10'],ISO/TC 34/SC 5,9599,,[40260],"['en','fr']",13,

21813,IS,,ISO 13370:1998,Thermal performance of buildings — Heat transfer via the ground — Calculation methods,Performance thermique des bâtiments —Transfert de chaleur par le sol — Méthodes de calcul,1998-10-22,1,['91.120.10'],ISO/TC 163/SC 2,9599,,[40965],"['en','fr']",47,

40965,IS,,ISO 13370:2007,Thermal performance of buildings — Heat transfer via the ground — Calculation methods,Performance thermique des bâtiments — Transfert de chaleur par le sol — Méthodes de calcul,2007-12-05,2,['91.120.10'],ISO/TC 163/SC 2,9599,[21813],[65716],"['en','fr']",48,"<p>ISO 13370:2007 provides methods of calculation of heat transfer coefficients and heat flow rates for building elements in thermal contact with the ground, including slab-on-ground floors, suspended floors and basements. It applies to building elements, or parts of them, below a horizontal plane in the bounding walls of the building situated</p><ul><li> for slab-on-ground floors, suspended floors and unhe

21830,IS,,ISO 13372:2004,Condition monitoring and diagnostics of machines — Vocabulary,Surveillance et diagnostic des machines — Vocabulaire,2004-05-27,1,"['01.040.17','17.160']",ISO/TC 108/SC 5,9599,,[52256],"['en','fr']",10,<p>ISO 13372:2004 specifies definitions of terms used in condition monitoring and diagnostics of machines. It is intended to provide users and manufacturers of condition monitoring and diagnostics systems with a common vocabulary.</p>

33163,IS,,ISO 13373-2:2005,"Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 2: Processing, analysis and presentation of vibration data","Surveillance et diagnostic d'état des machines — Surveillance des vibrations — Partie 2: Traitement, analyse et présentation des données vibratoires",2005-07-27,1,['17.160'],ISO/TC 108/SC 2,9599,,[68128],"['en','fr']",32,"<p>ISO 13373-2:2005 recommends procedures for processing and presenting vibration data and analysing vibration signatures for the purpose of monitoring the vibration condition of rotating machinery, and performing diagnostics as appropriate. Different techniques are described for different applicati

39836,IS,,ISO 13379-1:2012,Condition monitoring and diagnostics of machines — Data interpretation and diagnostics techniques — Part 1: General guidelines,Surveillance et diagnostic d'état des machines — Interprétation des données et techniques de diagnostic — Partie 1: Lignes directrices générales,2012-05-03,1,['17.160'],ISO/TC 108/SC 5,9599,[21839],[88027],"['en','fr']",33,"<p>This part of ISO 13379 gives guidelines for the data interpretation and diagnostics of machines. It is intended to</p><p>— allow the users and manufacturers of condition monitoring and diagnostics systems to share common</p><p>concepts in the fields of machine diagnostics;</p><p>— enable users to prepare the necessary

21839,IS,,ISO 13379:2003,Condition monitoring and diagnostics of machines — General guidelines on data interpretation and diagnostics techniques,Surveillance et diagnostic d'état des machines — Lignes directrices générales sur l'interprétation des données et les techniques de diagnostic,2003-08-19,1,['17.160'],ISO/TC 108/SC 5,9599,,[39836],"['en','fr']",25,"<p>ISO 13379:2003 gives guidance for data interpretation and diagnostics of machines. It is intended to allow the users and manufacturers of condition monitoring and diagnostics systems to share common concepts in the fields of machine diagnostics; to enable users to prepare the necessary technical characteristics that will be used for th

21840,IS,,ISO 13380:2002,Condition monitoring and diagnostics of machines — General guidelines on using performance parameters,Surveillance et diagnostic d'état des machines — Recommandations générales sur l'utilisation des paramètres de performance,2002-04-25,1,['17.160'],ISO/TC 108/SC 5,9599,,[39912],"['en','fr']",19,"<p>This International Standard describes the general conditions and procedures for recording, assessment, evaluation and diagnostics of machine condition by measuring parameters related to machine performance, condition and safety, including thermal, electrical and hydraulic parameters where applicable.</p><p>The procedures relate to operational monitoring of machines, and i

21841,IS,,ISO 13381-1:2004,Condition monitoring and diagnostics of machines — Prognostics — Part 1: General guidelines,Surveillance et diagnostic des machines — Pronostic — Partie 1: Lignes directrices générales,2004-11-08,1,['17.160'],ISO/TC 108/SC 5,9599,,[51436],"['en','fr']",20,"<p>ISO 13381-1:2004 provides guidance for the development of prognosis processes. It is intended to allow the users and manufacturers of condition monitoring and diagnostics systems to share common concepts in the fields of machinery fault prognosis; to enable users to determine the necessary data, characteristics and behaviour necessary for accurate prognosis; to outline an appropriate approach to prognosis de

51436,IS,,ISO 13381-1:2015,Condition monitoring and diagnostics of machines — Prognostics — Part 1: General guidelines,Surveillance et diagnostic des machines — Pronostic — Partie 1: Lignes directrices générales,2015-09-29,2,['17.160'],ISO/TC 108/SC 5,9599,[21841],[88029],"['en','fr']",21,"<p>ISO 13381-1:2015 provides guidance for the development and application of prognosis processes. It is intended to</p><p>- allow developers, providers, users and manufacturers to share common concepts of prognostics,</p><p>- enable users to determine the data, characteristics, processes and behaviours necessary for accurate prognosis,</p><p>- outline appropriate approaches and processes t

42799,IS,,ISO 13385-1:2011,Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Callipers; Design and metrological characteristics,Spécification géométrique des produits (GPS) — Équipement de mesurage dimensionnel — Partie 1: Pieds à coulisse; caractéristiques de conception et caractéristiques métrologiques,2011-07-14,1,['17.040.30'],ISO/TC 213,9599,"[9019,13425]",[71149],"['en','fr']",21,<p>ISO 13385-1:2011 provides the most important design and metrological characteristics of callipers with analogue indication [vernier scale or circular scale (dial)] and with digital indication (digital display).</p>

42801,IS,,ISO 13385-2:2011,Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 2: Calliper depth gauges; Design and metrological characteristics,Spécification géométrique des produits (GPS) — Équipement de mesurage dimensionnel — Partie 2: Jauges de profondeur; caractéristiques de conception et caractéristiques métrologiques,2011-07-14,1,['17.040.30'],ISO/TC 213,9599,"[9019,13425]",[77153],"['en','fr']",16,<p>ISO 13385-2:2011 provides the most important design and metrological characteristics of calliper depth gauges with analogue indication [vernier scale or circular scale (dial)] and with digital indication (digital display).</p>

21886,IS,,ISO 13397-2:1996,"Periodontal curettes, dental scalers and excavators — Part 2: Periodontal curettes — Gr-type","Curettes parodontales, instruments dentaires pour détartrage et excavateurs dentaires — Partie 2: Curettes parodontales — Type Gr",1996-08-29,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[34572],"['en','fr']",3,<p>Gives the dimensions for Gr-type periodontal curettes.</p>

29881,IS,Cor,ISO 13397-2:1996/Cor 1:1997,"Periodontal curettes, dental scalers and excavators — Part 2: Periodontal curettes — Gr-type — Technical Corrigendum 1","Curettes parodontales, instruments dentaires pour détartrage et excavateurs dentaires — Partie 2: Curettes parodontales — Type Gr — Rectificatif technique 1",1997-12-25,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[34572],"['en','fr']",2,

23078,IS,,ISO 13397-4:1997,"Periodontal curettes, dental scalers and excavators — Part 4: Dental excavators — Discoid-type","Curettes parodontales, instruments dentaires pour détartrage et excavateurs dentaires — Partie 4: Excavateurs dentaires — Type discoïde",1997-12-11,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[77398],"['en','fr']",5,

21888,IS,,ISO 13398:1997,Refrigerated light hydrocarbon fluids — Liquefied natural gas — Procedure for custody transfer on board ship,Hydrocarbures légers réfrigérés — Gaz naturels liquéfiés — Procédure de transfert de garde à bord des navires,1997-11-27,1,['03.220.40'],ISO/TC 28/SC 5,9599,,[46482],"['en','fr']",11,

3947,IS,,ISO 134:1973,Withdrawal of ISO 134-1973,Annulation de l'ISO 134-1973,1973-09-01,1,['23.040.10'],ISO/TC 5,9599,,[9985],['en'],2,

53765,IS,,ISO 13400-1:2011,Road vehicles — Diagnostic communication over Internet Protocol (DoIP) — Part 1: General information and use case definition,Véhicules routiers — Communication de diagnostic au travers du protocole internet (DoIP) — Partie 1: Informations générales et définition de cas d'usage,2011-10-18,1,"['43.040.10','43.180']",ISO/TC 22/SC 31,9599,,[73793],['en'],15,"<p>ISO 13400-1:2011 describes the general use cases and communication scenarios which are covered by an Internet Protocol-based vehicle communication standard. Each use case drives specific communication capabilities of the vehicle communication interface, for instance in order to be interoperable in an existing co

53766,IS,,ISO 13400-2:2012,Road vehicles - Diagnostic communication over Internet Protocol (DoIP) — Part 2: Transport protocol and network layer services,Véhicules routiers — Communication de diagnostic au travers du protocole internet (DoIP) — Partie 2: Protocole de transport et services de la couche réseau,2012-06-04,1,"['43.040.10','43.180']",ISO/TC 22/SC 31,9599,,[74785],['en'],68,"<p>ISO 13400-2:2012 specifies the requirements for diagnostic communication between external test equipment and vehicle electronic components using Internet Protocol (IP) as well as the transmission control protocol (TCP) and user datagram protocol (UDP). This includes the definition of vehicle gateway require

74785,IS,,ISO 13400-2:2019,Road vehicles — Diagnostic communication over Internet Protocol (DoIP) — Part 2: Transport protocol and network layer services,Véhicules routiers — Communication de diagnostic au travers du protocole internet (DoIP) — Partie 2: Protocole de transport et services de la couche réseau,2019-12-13,2,"['43.040.10','43.180']",ISO/TC 22/SC 31,9599,[53766],[87961],['en'],78,"<p>This document specifies the requirements for secured and unsecured diagnostic communication between client DoIP entity and server(s) installed in the vehicle using Internet protocol (IP) as well as the transmission control protocol (TCP) and user datagram protocol (UDP). This includes the definition

84208,IS,Amd,ISO 13400-2:2019/Amd 1:2023,Road vehicles — Diagnostic communication over Internet Protocol (DoIP) — Part 2: Transport protocol and network layer services — Amendment 1,Véhicules routiers — Communication de diagnostic au travers du protocole internet (DoIP) — Partie 2: Protocole de transport et services de la couche réseau — Amendement 1,2023-07-24,2,"['43.040.10','43.180']",ISO/TC 22/SC 31,9599,,[87961],['en'],16,

53767,IS,,ISO 13400-3:2011,Road vehicles — Diagnostic communication over Internet Protocol (DoIP) — Part 3: Wired vehicle interface based on IEEE 802.3,Véhicules routiers — Communication de diagnostic au travers du protocole internet (DoIP) — Partie 3: Interface du véhicule câblé sur la base de l'IEEE802.3,2011-12-06,1,"['43.040.10','43.180']",ISO/TC 22/SC 31,9599,,[68424],['en'],13,

21241,IS,,ISO 13402:1995,"Surgical and dental hand instruments — Determination of resistance against autoclaving, corrosion and thermal exposure","Instruments chirurgicaux et dentaires à main — Détermination de la résistance au passage à l'autoclave, à la corrosion et à l'exposition à la chaleur",1995-07-27,1,"['11.060.20','11.040.30']",ISO/TC 170,9599,,[85618],"['en','fr']",4,"<p>Describes test methods to determine the resistance of stainless steel surgical and dental hand instruments against autoclaving, corrosion and thermal exposure.</p>"

41480,IS,,ISO 13404:2007,Prosthetics and orthotics — Categorization and description of external orthoses and orthotic components,Prothèses et orthèses — Classification et description des orthèses externes et des composants d'orthèses,2007-06-18,1,['11.040.40'],ISO/TC 168,9599,,[85316],"['en','ru']",7,<p>ISO 13404:2007 establishes a means of classifying and describing external orthoses and the components from which they are assembled.</p>

21915,IS,,ISO 13405-1:1996,Prosthetics and orthotics — Classification and description of prosthetic components — Part 1: Classification of prosthetic components,Prothèses et orthèses — Classification et description des composants de prothèses — Partie 1: Classification des composants de prothèses,1996-10-24,1,['11.040.40'],ISO/TC 168,9599,,[42289],"['en','fr']",3,<p>Contains a means of classifying the components of limb prostheses and their construction.</p>

21916,IS,,ISO 13405-2:1996,Prosthetics and orthotics — Classification and description of prosthetic components — Part 2: Description of lower-limb prosthetic components,Prothèses et orthèses — Classification et description des composants de prothèses — Partie 2: Description des composants de prothèses des membres inférieurs,1996-10-24,1,['11.040.40'],ISO/TC 168,9599,,[42290],"['en','fr']",9,<p>Establishes a method for describing lower-limb prosthetic components.</p>

21917,IS,,ISO 13405-3:1996,Prosthetics and orthotics — Classification and description of prosthetic components — Part 3: Description of upper-limb prosthetic components,Prothèses et orthèses — Classification et description des composants de prothèses — Partie 3: Description des composants de prothèses des membres supérieurs,1996-10-24,1,['11.040.40'],ISO/TC 168,9599,,[42291],"['en','fr']",12,<p>Establishes a method for describing upper-limb prosthetic components.</p>

25671,IS,,ISO 13406-1:1999,Ergonomic requirements for work with visual displays based on flat panels — Part 1: Introduction,Exigences ergonomiques pour travail sur écrans de visualisation à panneaux plats — Partie 1: Introduction,1999-10-07,1,"['13.180','35.180']",ISO/TC 159/SC 4,9599,,"[40100,40097]","['en','fr']",3,

25670,IS,,ISO 13406-2:2001,Ergonomic requirements for work with visual displays based on flat panels — Part 2: Ergonomic requirements for flat panel displays,Exigences ergonomiques pour travail sur écrans de visualisation à panneau plat — Partie 2: Exigences ergonomiques des écrans à panneau plat,2001-12-20,1,"['13.180','35.180']",ISO/TC 159/SC 4,9599,,"[40098,40102,40100,40097]","['en','fr']",147,

21197,IS,,ISO 13407:1999,Human-centred design processes for interactive systems,Processus de conception centrée sur l'opérateur humain pour les systèmes interactifs,1999-06-10,1,['13.180'],ISO/TC 159/SC 4,9599,,[52075],"['en','fr']",26,

21925,IS,,ISO 13408-1:1998,Aseptic processing of health care products — Part 1: General requirements,Traitement aseptique des produits de santé — Partie 1: Exigences générales,1998-07-23,1,['11.080.01'],ISO/TC 198,9599,,[37842],"['en','fr']",31,

37842,IS,,ISO 13408-1:2008,Aseptic processing of health care products — Part 1: General requirements,Traitement aseptique des produits de santé — Partie 1: Exigences générales,2008-06-10,2,['11.080.01'],ISO/TC 198,9599,[21925],[77151],"['en','fr','ru']",45,"<p>ISO 13408-1:2008 specifies the general requirements for, and offers guidance on, processes, programmes and procedures for development, validation and routine control of the manufacturing process for aseptically-processed health care products.</p><p>ISO 13408-1:2008 includes requirements and guidance relative to the overall topic of aseptic processing. Specific requirements and guidance on various specialized processes and methods relat

59475,IS,Amd,ISO 13408-1:2008/Amd 1:2013,Aseptic processing of health care products — Part 1: General requirements — Amendment 1,Traitement aseptique des produits de santé — Partie 1: Exigences générales — Amendement 1,2013-04-17,2,['11.080.01'],ISO/TC 198,9599,,[77151],"['en','fr','ru']",8,

30058,IS,,ISO 13408-2:2003,Aseptic processing of health care products — Part 2: Filtration,Traitement aseptique des produits de santé — Partie 2: Filtration,2003-03-26,1,['11.080.01'],ISO/TC 198,9599,,[66452],"['en','fr']",11,"<p>ISO 13408-2:2003 specifies requirements for sterilizing filtration as part of aseptic processing of health care products. It also offers guidance to filter users concerning general requirements for set-up, validation and routine operation of a sterilizing filtration process, to be used for aseptic processing of health care products. </p><p>ISO 13408-2:2003 is not applicable to removal of viruses. Sterilizing filtration is not applicable to fluids containing particle

39782,IS,,ISO 13408-6:2005,Aseptic processing of health care products — Part 6: Isolator systems,Traitement aseptique des produits de santé — Partie 6: Systèmes isolateurs,2005-06-20,1,['11.080.01'],ISO/TC 198,9599,,[72836],"['en','fr']",17,"<p>ISO 13408-6:2005 specifies the requirements for isolator systems used for aseptic processing and offers guidance on qualification, bio-decontamination, validation, operation and control of isolator systems used for aseptic processing of health care products.</p><p>ISO 13408-6:2005 is focused on the use of isolator systems to maintain aseptic conditions; this may include applications for hazardous materials.</p><p>ISO 13408-6:2005 does not supersede or

59476,IS,Amd,ISO 13408-6:2005/Amd 1:2013,Aseptic processing of health care products — Part 6: Isolator systems — Amendment 1,Traitement aseptique des produits de santé — Partie 6: Systèmes isolateurs — Amendement 1,2013-03-12,1,['11.080.01'],ISO/TC 198,9599,,[72836],"['en','fr']",4,

21968,IS,,ISO 13419:1997,Space data and information transfer systems — Packet telemetry,Systèmes de transfert des informations et données spatiales — Télémesure par paquets,1997-12-25,1,['49.140'],ISO/TC 20/SC 13,9599,,[36479],"['en','fr']",34,

5908,IS,,ISO 1342:1988,Oil of rosemary (Rosmarinus officinalis Linnaeus),Huile essentielle de romarin (Rosmarinus officinalis Linnaeus),1988-12-15,1,['71.100.60'],ISO/TC 54,9599,[5907],[25315],"['en','fr']",10,

25315,IS,,ISO 1342:2000,Oil of rosemary (Rosmarinus officinalis L.),Huile essentielle de romarin (Rosmarinus officinalis L.),2000-11-02,2,['71.100.60'],ISO/TC 54,9599,[5908],[56521],"['en','fr']",8,

21969,IS,,ISO 13420:1997,Space data and information transfer systems — Advanced orbiting systems — Networks and data links — Architectural specification,Systèmes de transfert des informations et données spatiales — Systèmes perfectionnés sur orbite — Réseaux et liaisons de données — Spécification de l'architecture,1997-12-25,1,['49.140'],ISO/TC 20/SC 13,9599,,[36450],"['en','fr']",165,

36937,IS,,ISO 13426-1:2003,Geotextiles and geotextile-related products — Strength of internal structural junctions — Part 1: Geocells,Géotextiles et produits apparentés — Résistance des liaisons de structures internes — Partie 1: Géosynthétiques alvéolaires,2003-01-09,1,['59.080.70'],ISO/TC 221,9599,,[69497],['en'],13,

36938,IS,,ISO 13426-2:2005,Geotextiles and geotextile-related products — Strength of internal structural junctions — Part 2: Geocomposites,Géotextiles et produits apparentés — Résistance des liaisons de structures internes — Partie 2: Géocomposites,2005-04-15,1,['59.080.70'],ISO/TC 221,9599,,[82435],"['en','fr']",10,<p>ISO 13426-2:2005 describes index tests for determining the strength of the internal structural junctions of all geocomposites and of clay geosynthetic barriers.</p>

21992,IS,,ISO 13427:1998,Geotextiles and geotextile-related products — Abrasion damage simulation (sliding block test),Géotextiles et produits apparentés — Simulation de l'endommagement par abrasion (essai du bloc glissant),1998-08-27,1,['59.080.70'],ISO/TC 221,9599,,[57244],"['en','fr']",6,

36713,IS,,ISO 13428:2005,Geosynthetics — Determination of the protection efficiency of a geosynthetic against impact damage,Géosynthétiques — Détermination de l'efficacité de protection d'un géosynthétique contre l'effet d'un impact,2005-02-10,1,['59.080.70'],ISO/TC 221,9599,,[82436],"['en','fr']",9,"<p>ISO 13428:2005 describes an index test for the determination of the protection efficiency of a geosynthetic on a hard surface, exposed to the impact load of a hemispherical object.</p><p>The index test measures the change in thickness of a thin lead plate lying between the geosynthetic and a rigid support. </p>"

21996,IS,,ISO 13431:1999,Geotextiles and geotextile-related products — Determination of tensile creep and creep rupture behaviour,Géotextiles et produits apparentés — Détermination du comportement au fluage en traction et de la rupture au fluage en traction,1999-08-26,1,['59.080.70'],ISO/TC 221,9599,,[83579],"['en','fr']",16,

36718,IS,,ISO 13433:2006,Geosynthetics — Dynamic perforation test (cone drop test),Géosynthétiques — Essai de perforation dynamique (essai par chute d'un cône),2006-08-07,1,['59.080.70'],ISO/TC 221,9599,,[83580],"['en','fr']",6,"<p>ISO 13433:2006 specifies a method to determine the resistance of geosynthetics to penetration by a steel cone dropped from a fixed height. The degree of penetration is an indication of the behaviour of the geosynthetic when sharp stones are dropped on its surface. </p><p>The method is generally applicable to geosynthetics. However, the validity of this test for some types of products should be considered carefully, as the test principle may not be applicable.</p>"

25121,IS,,ISO 13437:1998,"Geotextiles and geotextile-related products — Method for installing and extracting samples in soil, and testing specimens in laboratory",Géotextiles et produits apparentés — Méthode pour l'installation et l'extraction d'échantillons dans le sol et pour la réalisation d'essais en laboratoire sur les éprouvettes,1998-08-27,1,['59.080.70'],ISO/TC 221,9599,,[72245],"['en','fr']",9,

36898,IS,,ISO 13438:2004,Geotextiles and geotextile-related products — Screening test method for determining the resistance to oxidation,Géotextiles et produits apparentés — Méthode de détermination de la résistance à l'oxydation,2004-10-29,1,['59.080.70'],ISO/TC 221,9599,[22003],[65541],"['en','fr']",9,<p>ISO 13438:2004 specifies a screening test method for determining the resistance of geotextiles and geotextile-related products to oxidation. The test is applicable to polypropylene- and polyethylene-based products.</p><p>The data are suitable for screening purposes but not for deriving performance data such as lifetime unless supported by further evidence.</p>

37524,IS,,ISO 13442:2004,Tyres and rims for construction machines,Pneumatiques et jantes pour engins de construction,2004-03-30,1,"['91.220','83.160.99']",ISO/TC 31/SC 6,9599,,[63458],"['en','fr']",12,"<p>ISO 13442:2004 sets the designation, dimensions, load ratings and reference speeds for tyres and rims fitted to construction machines (backhoe loaders, small dumpers, loaders, excavators etc.) operating on building sites under loading and transport conditions.</p>"

22013,IS,,ISO 13445:1995,Adhesives — Determination of shear strength of adhesive bonds between rigid substrates by the block-shear method,Adhésifs — Détermination de la résistance en cisaillement d'adhésifs de joints collés par la méthode de cisaillement entre éléments massiques,1995-08-03,1,['83.180'],ISO/TC 61/SC 11,9599,,[34853],"['en','fr']",4,<p>Describes a method for the determination of the shear strength of adhesive bonds between materials with elastic moduli higher than the elastic modulus of the adhesive. Allows an estimation of the shear strength of an adhesive on machinable and non-machinable materials.</p>