Withdrawn and superseded ISO standards — page 177 of 246

56454,IS,,ISO 8765:2011,Hexagon head bolts with metric fine pitch thread — Product grades A and B,Vis à tête hexagonale à filetage métrique à pas fin partiellement filetées — Grades A et B,2011-03-15,3,['21.060.10'],ISO/TC 2/SC 11,9599,[26381],[72583],"['en','fr']",11,"<p>ISO 8765:2011 specifies the characteristics of hexagon head bolts with metric fine pitch thread with nominal thread diameters, <i>d</i>,<i> </i>from 8 mm to 64 mm, of product grade A for nominal thread diameters,<i> d</i>,<i> </i>from 8 mm to 24 mm and nominal lengths, <i>l</i>, up to and including 10<i>d</i> or 150 mm, whichever is the shorter, and of product grade B for nominal thread diameters,<i> </i><i>d</i>, over 24 m

16179,IS,,ISO 8767:1992,Passenger car tyres — Methods of measuring rolling resistance,Pneumatiques pour voitures particulières — Méthodes de mesure de la résistance au roulement,1992-07-23,1,['83.160.10'],ISO/TC 31/SC 3,9599,,[33328],"['en','fr']",11,"<p>Specifies the following test methods for new pneumatic tyres: force method, torque method, power method, deceleration method. Annex A considers test equipment tolerances, Annex B optional test conditions, Annex C measurement methods of moment of inertia for drum and tyre assembly for the deceleration method.</p>"

16182,IS,,ISO 8769:1988,"Reference sources for the calibration of surface contamination monitors — Beta-emitters (maximum beta energy greater than 0,15 MeV) and alpha-emitters","Sources de référence pour l'étalonnage des moniteurs de contamination de surface — Émetteurs bêta (énergie bêta maximale supérieure à 0,15 MeV) et émetteurs alpha",1988-06-23,1,['17.240'],ISO/TC 85/SC 2,9599,,"[41230,45992]","['en','fr']",5,"<p>Specifies the characteristics of reference sources and reference radiations which take the form of adequately characterized large-area sources specified in terms of activity (per unit area) and surface emission rate. Regulatory documents refer to surface contamination in terms

16183,IS,,ISO 8769-2:1996,"Reference sources for the calibration of surface contamination monitors — Part 2: Electrons of energy less than 0,15 MeV and photons of energy less than 1,5 MeV","Sources de référence destinées à l'étalonnage de sondes de contamination de surface — Partie 2: Électrons d'énergie inférieure à 0,15 MeV et photons d'énergie inférieure à 1,5 MeV",1996-11-21,1,['17.240'],ISO/TC 85/SC 2,9599,,[45992],"['en','fr']",10,"<p>Specifies the characteristics of reference sources for the calibration of surface contamination monitors that are traceable to national measurement standards. Relates to a series of sources emitting electrones of energy less than 0,15 MeV and photons of e

45992,IS,,ISO 8769:2010,"Reference sources — Calibration of surface contamination monitors — Alpha-, beta- and photon emitters","Sources de référence — Étalonnage des contrôleurs de contamination de surface — Émetteurs alpha, bêta et photoniques",2010-09-03,2,['17.240'],ISO/TC 85/SC 2,9599,"[16182,16183]",[63915],"['en','fr']",12,"<p>ISO 8769:2010 specifies the characteristics of reference sources of radioactive surface contamination, traceable to national measurement standards, for the calibration of surface contamination monitors. ISO 8769:2010 relates to alpha-emitters, beta-emitters and photon emitters of maximum photon energy not greater than 1,5 MeV. It does not describe the procedures

63915,IS,,ISO 8769:2016,"Reference sources — Calibration of surface contamination monitors — Alpha-, beta- and photon emitters","Sources de référence — Étalonnage des contrôleurs de contamination de surface — Émetteurs alpha, bêta et photoniques",2016-01-04,3,['17.240'],ISO/TC 85/SC 2,9599,[45992],[76014],"['en','fr']",14,"<p>ISO 8769:2016 specifies the characteristics of reference sources of radioactive surface contamination, traceable to national measurement standards, for the calibration of surface contamination monitors. This International Standard relates to alpha-emitters, beta-emitters, and photon emitters of maximum photon energy not greater than 1,5 MeV. It does not describe the pro

41657,IS,,ISO 877-1:2009,Plastics — Methods of exposure to solar radiation — Part 1: General guidance,Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 1: Lignes directrices générales,2009-05-29,1,['83.080.01'],ISO/TC 61/SC 6,9599,[5263],"[67567,85969]","['en','fr','ru']",13,"<p>ISO 877-1:2009 provides information and general guidance on the selection and use of the methods of exposure to solar radiation described in detail in subsequent parts of ISO 877. These methods of exposure to solar radiation are applicable to plastics materials of all kinds as well as to products and portions of products.</p><p>It also specifies methods for determining radiant exposure.</p><p>It does

5262,IS,,ISO 877:1976,Plastics — Determination of resistance to change upon exposure under glass to daylight,Matières plastiques — Détermination de la résistance aux changements de propriétés par exposition sous verre à la lumière du jour,1976-09-01,1,['83.080'],ISO/TC 61,9599,,[5263],"['en','fr']",8,

5263,IS,,ISO 877:1994,"Plastics — Methods of exposure to direct weathering, to weathering using glass-filtered daylight, and to intensified weathering by daylight using Fresnel mirrors","Plastiques — Méthodes d'exposition directe aux intempéries, ou d'exposition indirecte sous verre, et à la lumière du jour intensifiée par des miroirs de Fresnel",1994-08-04,2,['83.080.01'],ISO/TC 61/SC 6,9599,"[10542,5262]","[41657,43425,41658]","['en','fr']",20,"<p>Cancels and replaces the first edition (1976). Specifies methods of exposing plastics to solar radiation, either by direct exposure to natural weathering (Method A), to indirect solar radiation by modification of its spectral distribution with gl

41658,IS,,ISO 877-2:2009,Plastics — Methods of exposure to solar radiation — Part 2: Direct weathering and exposure behind window glass,Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 2: Exposition directe et exposition derrière une vitre en verre,2009-05-29,1,['83.080.01'],ISO/TC 61/SC 6,9599,[5263],"[85971,67568]","['en','fr','ru']",6,<p>ISO 877-2:2009 specifies a method for the direct exposure of plastics to solar radiation and a method for the exposure of plastics to glass-filtered solar radiation (exposure behind window glass). The purpose is to assess property changes produced after specified stages of such exposures.</p>

43425,IS,,ISO 877-3:2009,Plastics — Methods of exposure to solar radiation — Part 3: Intensified weathering using concentrated solar radiation,Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 3: Exposition intensifiée par rayonnement solaire concentré,2009-05-29,1,['83.080.01'],ISO/TC 61/SC 6,9599,[5263],[67566],"['en','fr','ru']",11,<p>ISO 877-3:2009 specifies a method for exposing plastics to concentrated solar radiation using reflecting concentrators to accelerate the weathering processes. The purpose is to assess property changes produced after specified stages of such exposures.</p>

67566,IS,,ISO 877-3:2018,Plastics — Methods of exposure to solar radiation — Part 3: Intensified weathering using concentrated solar radiation,Plastiques — Méthodes d'exposition au rayonnement solaire — Partie 3: Exposition intensifiée par rayonnement solaire concentré,2018-04-13,2,['83.080.01'],ISO/TC 61/SC 6,9599,[43425],[88062],"['en','fr']",11,"<p>ISO 877-3:2018 specifies a method for exposing plastics to concentrated solar radiation using reflecting concentrators to accelerate the weathering processes. The purpose is to assess property changes produced after specified stages of such exposures. The reflecting concentrators used in these exposures are sometimes referred to as 'Fresnel ref

16185,IS,,ISO 8770:1991,High-density polyethylene (PE-HD) pipes and fittings for soil and waste discharge (low and high temperature) systems inside buildings — Specifications,Tubes et raccords en polyéthylène haute densité (PE-HD) pour les systèmes d'évacuation d'eaux usées et d'eaux-vannes (à basse et à haute température) à l'intérieur des bâtiments — Spécifications,1991-06-13,1,"['91.140.80','83.140.30']",ISO/TC 138/SC 1,9599,,[33706],"['en','fr']",18,

16187,IS,,ISO 8772:1991,High-density polyethylene (PE-HD) pipes and fittings for buried drainage and sewerage systems — Specifications,Tubes et raccords en polyéthylène haute densité (PE-HD) pour les systèmes d'assainissement enterrés et les égouts souterrains — Spécifications,1991-05-16,1,"['93.030','23.040.45','91.140.80','23.040.20']",ISO/TC 138/SC 1,9599,,[39901],"['en','fr']",15,

16188,IS,,ISO 8773:1991,Polypropylene (PP) pipes and fittings for buried drainage and sewerage systems — Specifications,Tubes et raccords en polypropylène (PP) pour les systèmes d'assainissement enterrés et les égouts souterrains — Spécifications,1991-05-16,1,"['93.030','23.040.45','91.140.80','23.040.20']",ISO/TC 138/SC 1,9599,,[39902],"['en','fr']",15,

16191,IS,,ISO 8776:1988,Photography — Photographic film — Determination of folding endurance,Photographie — Film photographique — Détermination de la résistance au pliage,1988-06-16,1,['37.040.20'],ISO/TC 42,9599,,[31932],"['en','fr']",4,

16193,IS,,ISO 8778:1990,Pneumatic fluid power — Standard reference atmosphere,Transmissions pneumatiques — Atmosphère normale de référence,1990-08-23,1,['23.100.01'],ISO/TC 131,9599,,[26559],"['en','fr']",1,

16194,IS,,ISO 8779:1992,Polyethylene (PE) pipes for irrigation laterals — Specifications,Tubes en polyéthylène (PE) pour branchements d'irrigation — Spécifications,1992-07-02,1,"['65.060.35','83.140.30']",ISO/TC 138/SC 2,9599,,[29778],"['en','fr']",5,"<p>Specifies the test methods and required properties for the pipes: material, dimensions and pressures, resistance to internal pressure, longitudinal reversion, susceptibility to environmental stress-cracking.</p>"

29778,IS,,ISO 8779:2001,Polyethylene (PE) pipes for irrigation laterals — Specifications,Tubes en polyéthylène (PE) pour branchements d'irrigation — Spécifications,2001-09-06,2,"['23.040.20','65.060.35']",ISO/TC 138/SC 2,9599,[16194],[45550],"['en','fr']",7,

45550,IS,,ISO 8779:2010,Plastics piping systems — Polyethylene (PE) pipes for irrigation — Specifications,Systèmes de canalisations en plastique — Tubes en polyéthylène (PE) pour l'irrigation — Spécifications,2010-02-23,3,"['23.040.20','65.060.35']",ISO/TC 138/SC 2,9599,[29778],[70102],"['en','fr']",14,"<p>ISO 8779:2010 specifies the pipes (mains, sub-mains and laterals) with nominal outside diameters from 12 mm up to and including 63 mm made from polyethylene (PE) intended to be used for the conveyance of water for irrigation.</p><p>It also specifies the general properties of PE and the test parameters for the pipes designated as PE 32 and PE 40 by checking referenced points, to be used und

64585,IS,Amd,ISO 8779:2010/Amd 1:2014,Plastics piping systems — Polyethylene (PE) pipes for irrigation — Specifications — Amendment 1,Systèmes de canalisations en plastique — Tubes en polyéthylène (PE) pour l'irrigation — Spécifications — Amendement 1,2014-06-02,3,"['23.040.20','65.060.35']",ISO/TC 138/SC 2,9599,,[70102],"['en','fr']",1,

16204,IS,,ISO 8782-1:1998,"Safety, protective and occupational footwear for professional use — Part 1: Requirements and test methods","Chaussures de sécurité, de protection et de travail à usage professionnel — Partie 1: Exigences et méthodes d'essai",1998-12-17,1,['13.340.50'],ISO/TC 94/SC 3,9599,,"[32389,32330]","['en','fr']",68,

16205,IS,,ISO 8782-2:1998,"Safety, protective and occupational footwear for professional use — Part 2: Specification for safety footwear","Chaussures de sécurité, de protection et de travail à usage professionnel — Partie 2: Spécifications pour chaussures de sécurité",1998-12-17,1,['13.340.50'],ISO/TC 94/SC 3,9599,,"[32331,32390]","['en','fr']",6,

16206,IS,,ISO 8782-3:1998,"Safety, protective and occupational footwear for professional use — Part 3: Specification for protective footwear","Chaussures de sécurité, de protection et de travail à usage professionnel — Partie 3: Spécifications pour chaussures de protection",1998-12-17,1,['13.340.50'],ISO/TC 94/SC 3,9599,,"[32332,32391]","['en','fr']",6,

22112,IS,,ISO 8782-4:1998,"Safety, protective and occupational footwear for professional use — Part 4: Specification for occupational footwear","Chaussures de sécurité, de protection et de travail à usage professionnel — Partie 4: Spécifications pour chaussures de travail",1998-12-17,1,['13.340.50'],ISO/TC 94/SC 3,9599,,"[32334,32392]","['en','fr']",6,

30343,IS,,ISO 8782-5:2000,"Safety, protective and occupational footwear for professional use — Part 5: Additional requirements and test methods","Chaussures de sécurité, de protection et de travail à usage professionnel — Partie 5: Exigences additionnelles et méthodes d'essai",2000-03-02,1,['13.340.50'],ISO/TC 94/SC 3,9599,,[42259],"['en','fr']",15,

30344,IS,,ISO 8782-6:2000,"Safety, protective and occupational footwear for professional use — Part 6: Additional specifications for safety footwear","Chaussures de sécurité, de protection et de travail à usage professionnel — Partie 6: Spécifications additionnelles pour chaussures de sécurité",2000-03-02,1,['13.340.50'],ISO/TC 94/SC 3,9599,,[42260],"['en','fr']",6,

30345,IS,,ISO 8782-7:2000,"Safety, protective and occupational footwear for professional use — Part 7: Additional specifications for protective footwear","Chaussures de sécurité, de protection et de travail à usage professionnel — Partie 7: Spécifications additionnelles pour chaussures de protection",2000-03-02,1,['13.340.50'],ISO/TC 94/SC 3,9599,,[42261],"['en','fr']",3,

30346,IS,,ISO 8782-8:2000,"Safety, protective and occupational footwear for professional use — Part 8: Additional specifications for occupational footwear","Chaussures de sécurité, de protection et de travail à usage professionnel — Partie 8: Spécifications additionnelles pour chaussures de travail",2000-03-02,1,['13.340.50'],ISO/TC 94/SC 3,9599,,[42262],"['en','fr']",2,

29963,IS,,ISO 8783:1999,Alpine skis — Guidelines for conducting slope performance tests,Skis alpins — Principes directeurs pour la réalisation d'essais de performance sur piste,1999-06-24,1,['97.220.20'],ISO/TC 83/SC 4,9599,[16207],[65972],"['en','fr']",4,

65972,IS,,ISO 8783:2015,Alpine skis — Guidelines for conducting slope performance tests,Skis alpins — Principes directeurs pour la réalisation d'essais de performance sur piste,2015-07-24,2,['97.220.20'],ISO/TC 83/SC 4,9599,[29963],[92509],"['en','fr']",4,<p>ISO 8783:2015 provides guidelines for carrying out comparative testing of alpine skis with the objective of evaluating the performance characteristics.</p><p>It is applicable to alpine skis in accordance with ISO 6289.</p>

16208,IS,,ISO 8784-1:1987,Paper and board — Determination of microbiological properties — Part 1: Total bacterial count,Papier et carton — Détermination des propriétés microbiologiques — Partie 1: Dénombrement bactériologique total,1987-01-29,1,"['07.100.99','85.060']",ISO/TC 6/SC 2,9599,,[29895],"['en','fr']",5,"<p>Is applicable to most kinds of paper and board, especially food grades, and is not suitable for materials such as vegetable parchment or wet-strength paper which cannot be readily disintegrated.</p>"

29895,IS,,ISO 8784-1:2005,"Pulp, paper and board — Microbiological examination — Part 1: Total count of bacteria, yeast and mould based on disintegration","Pâte, papier et carton — Analyse microbienne — Partie 1: Dénombrement total des bactéries, levures et moisissures basé sur la désintégration",2005-06-30,2,"['07.100.99','85.060','85.040']",ISO/TC 6/SC 2,9599,[16208],[53064],"['en','fr','ru']",9,"<p>ISO 8784-1:2005 specifies a method for determining the total number of colony-forming units of bacteria, yeast and moulds in dry market pulp, paper and paperboard after disintegration. The enumeration relates to specific media.</p><p>ISO 8784-1:2005 is applicable to most kinds of paper and pape

16212,IS,,ISO 8788:1987,Aerospace — Fasteners — Tolerances of form and position for nuts,Aéronautique et espace — Éléments de fixation — Tolérances de forme et de position des écrous,1987-06-25,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[21423],"['en','fr','ru']",10,

21423,IS,,ISO 8788:2000,"Aerospace — Nuts, metric — Tolerances of form and position",Aéronautique et espace — Écrous métriques — Tolérances de forme et de position,2000-06-08,2,['49.030.30'],ISO/TC 20/SC 4,9599,[16212],[77133],"['en','fr']",22,"<p>This International Standard defines the tolerances of</p><p>form and position of metric nuts meant for aerospace</p><p>construction. These tolerances comply with ISO 1101,</p><p>ISO 2692 and ISO 5459.</p>"

16213,IS,,ISO 8789:1994,Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles — Specification,Tuyaux et flexibles en caoutchouc pour circulation de gaz de pétrole liquéfié dans les véhicules à moteur — Spécifications,1994-10-06,1,"['43.060.40','83.140.40']",ISO/TC 45/SC 1,9599,,[43706],"['en','fr']",3,"<p>Lays down the requirements for rubber hoses and hose assemblies, up to a maximum bore of 20 mm, for use in motor vehicles with liquefied petroleum gas installations. The hoses are designed for use up to a maximum pressure of 2,5 MPa and a working temperature between -40 °C and +80 °C.</p>"

43706,IS,,ISO 8789:2009,Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles — Specification,Tuyaux et flexibles en caoutchouc pour circulation de gaz de pétrole liquéfié dans les véhicules à moteur — Spécifications,2009-12-14,2,"['43.060.40','83.140.40']",ISO/TC 45/SC 1,9599,[16213],[68037],"['en','fr','ru']",8,"<p>ISO 8789:2009 specifies the requirements for rubber hoses and hose assemblies, up to a maximum hose size of 19, for use in motor vehicles with liquefied petroleum gas (LPG) installations. The hoses are designed for use up to a maximum working pressure of 3,0 MPa (30 bar) and at working temperatures from -40 °C up to and including +80 °C.</p>"

68037,IS,,ISO 8789:2018,Rubber hoses and hose assemblies for liquefied petroleum gas in motor vehicles — Specification,Tuyaux et flexibles en caoutchouc pour circulation de gaz de pétrole liquéfié dans les véhicules à moteur — Spécifications,2018-08-03,3,"['43.060.40','83.140.40']",ISO/TC 45/SC 1,9599,[43706],[77512],['en'],8,"<p>This document specifies the requirements for rubber hoses and hose assemblies, up to a maximum hose size of 19, for use in motor vehicles with liquefied petroleum gas (LPG) installations. The hoses are designed for use up to a maximum working pressure of 3,0 MPa (30 bar) and at working temperatures from −40 °C up to and including +80 °C.</p>"

16215,IS,,ISO 8791-1:1986,Paper and board — Determination of roughness/smoothness (air leak methods) — Part 1: General method,Papier et carton — Détermination de la rugosité/du lissé (méthodes du débit d'air) — Partie 1: Méthode générale,1986-09-11,1,['85.060'],ISO/TC 6/SC 2,9599,,"[45579,28521]","['en','fr']",2,"<p>Is applicable to most paper and board, and is not applicable to embossed or creped papers, or papers which will not lie flat under the conditions of test, or high air permeance papers which allow a significiant flow of air through the sheet. The Gurley instrument is excluded from this method.</p>"

16216,IS,,ISO 8791-2:1990,Paper and board — Determination of roughness/smoothness (air leak methods) — Part 2: Bendtsen method,Papier et carton — Détermination de la rugosité/du lissé (méthodes du débit d'air) — Partie 2: Méthode Bendtsen,1990-05-03,1,['85.060'],ISO/TC 6/SC 2,9599,[7417],"[51265,38050]","['en','fr']",8,

16217,IS,,ISO 8791-3:1990,Paper and board — Determination of roughness/smoothness (air leak methods) — Part 3: Sheffield method,Papier et carton — Détermination de la rugosité/du lissé (méthodes du débit d'air) — Partie 3: Méthode Sheffield,1990-05-03,1,['85.060'],ISO/TC 6/SC 2,9599,[7417],[27980],"['en','fr']",9,

27980,IS,,ISO 8791-3:2005,Paper and board — Determination of roughness/smoothness (air leak methods) — Part 3: Sheffield method,Papier et carton — Détermination de la rugosité/du lissé (méthodes du débit d'air) — Partie 3: Méthode Sheffield,2005-02-17,2,['85.060'],ISO/TC 6/SC 2,9599,[16217],"[53063,69064]","['en','ru']",12,"<p>ISO 8791-3:2005 specifies a method for the determination of the roughness of paper and board using the Sheffield apparatus.</p><p>The method is applicable to papers and boards which have Sheffield roughness values between 10 and about 3 000 ml per min. It is not suitable for soft papers which allow the lands of the test head to indent the surface, or for high air-perme

16218,IS,,ISO 8791-4:1992,Paper and board — Determination of roughness/smoothness (air leak methods) — Part 4: Print-surf method,Papier et carton — Détermination de la rugosité/du lissé (méthodes du débit d'air) — Partie 4: Méthode Print-surf,1992-04-30,1,['85.060'],ISO/TC 6/SC 2,9599,,[38049],"['en','fr']",12,"<p>Should be read in conjunction with ISO 8791-1. Applicable to all printing papers and boards with which it is possible to form a substantially airtight seal against the guard lands of the measuring head. Annex A gives a method of calculation of roughness, Annex B specifies maintenance of the roughness testers, Annex D its calibration against ISO reference standards.</p>"

38049,IS,,ISO 8791-4:2007,Paper and board — Determination of roughness/smoothness (air leak methods) — Part 4: Print-surf method,Papier et carton — Détermination de la rugosité/du lissé (méthodes du débit d'air) — Partie 4: Méthode Print-surf,2007-11-07,2,['85.060'],ISO/TC 6/SC 2,9599,[16218],"[76350,60353]",['en'],22,"<p>ISO 8791-4:2007 specifies a method for determining the roughness of paper and board using an apparatus which complies with the Print-surf method, as defined in ISO 8791-4:2007. It is applicable to all printing papers and boards with which it is possible to form a substantially airtight seal against the guard lands of the measuring head.</p>"

16221,IS,,ISO 8794:1986,Steel wire ropes — Spliced eye terminations for slings,Câbles en acier — Oeils épissés pour élingues,1986-12-11,1,['77.140.65'],ISO/TC 105,9599,,[74043],"['en','fr']",5,<p>Specifies minimum requirements for spliced eye terminations for wire rope slings. Prototype tests covering the type acceptance of splice methods are also specified.</p>

16222,IS,,ISO 8795:1990,Plastics pipes for the transport of water intended for human consumption — Extractability of constituents — Test method,Tubes en matières plastiques pour l'alimentation en eau destinée à la consommation humaine — Extractabilité des constituants — Méthode d'essai,1990-12-13,1,"['91.140.60','83.140.30']",ISO/TC 138/SC 5,9599,,[26617],"['en','fr']",4,

26617,IS,,ISO 8795:1998,Plastics piping systems for the conveyance of water intended for human consumption — Migration assessment — Determination of migration values for plastics pipes,Systèmes de canalisations en plastiques pour le transport d'eau destinée à la consommation humaine — Evaluation de la migration — Détermination des valeurs de migration des tubes plastiques,1998-04-09,2,"['23.040.20','91.140.60']",ISO/TC 138/SC 5,9599,[16222],[31311],"['en','fr']",16,

16223,IS,,ISO 8796:1989,Polyethylene (PE) 25 pipes for irrigation laterals — Susceptibility to environmental stress-cracking induced by insert-type fittings — Test method and specification,Tubes en polyéthylène (PE) 25 pour branchements d'irrigation — Sensibilité à la fissuration sous contrainte produite par les raccords à insert — Méthode d'essai et spécifications,1989-08-10,1,"['65.060.35','83.140.30']",ISO/TC 138/SC 2,9599,,[29645],"['en','fr']",2,

16225,IS,,ISO 8798:1987,Acoustics — Reference levels for narrow-band masking noise,Acoustique — Niveaux de référence pour bruit de masque en bande étroite,1987-12-17,1,['13.140'],ISO/TC 43,9599,,[22496],"['en','fr']",5,

16226,IS,,ISO 8799:1988,Surface active agents — Sulfated ethoxylated alcohols and alkylphenols — Determination of content of unsulfated matter,Agents de surface — Sulfates d'alcools et d'alkylphénols éthoxylés — Détermination de la teneur en matière insulfatée,1988-03-31,1,['71.100.40'],ISO/TC 91,9599,,[52126],"['en','fr']",2,"<p>From a methanolic solution of the test portion, the unsulfated matter is separated on an ion-exchange column (filled with a mixture of cation-exchange resins and anion-exchange resins). The unsulfated matter is recovered from the eluate by evaporation and weighing of the residue.</p>"

16235,IS,,ISO 8802-3:1989,Information processing systems — Local and metropolitan area networks — Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications,Systèmes de traitement de l'information — Réseaux locaux et métropolitains — Partie 3: Accès multiple par surveillance du signal et détection de collision et spécifications pour la couche physique,1989-03-23,1,['35.110'],ISO/IEC JTC 1/SC 6,9599,,"[16236,16242]",['en'],,

16261,IS,,ISO 8812:1999,Earth-moving machinery — Backhoe loaders — Definitions and commercial specifications,Engins de terrassement — Chargeuses-pelleteuses — Définitions et spécifications commerciales,1999-12-16,1,"['01.040.53','53.100']",ISO/TC 127/SC 4,9599,,[62355],"['en','fr']",19,

16269,IS,,ISO 8819:1987,Liquified petroleum gases — Detection of hydrogen sulfide — Lead acetate method,Gaz de pétrole liquéfiés — Détection de l'acide sulfhydrique — Méthode à l'acétate de plomb,1987-10-15,1,['75.160.30'],ISO/TC 28,9599,,[22575],['en'],3,

5268,IS,,ISO 882:1980,Cardamoms — Specification,"Cardamome de Malabar, Cardamome de Ceylan — Spécifications",1980-10-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,"[5269,5270]","['en','fr']",3,

16270,IS,,ISO 8820-1:1994,"Road vehicles — Blade-type electric fuse-links — Part 1: Rated current, identification, test procedures and performance requirements","Véhicules routiers — Fusibles électriques plats — Partie 1: Intensité nominale, identification, méthodes d'essai et exigences de performance",1994-07-28,1,['43.040.10'],ISO/TC 22,9599,,[28286],"['en','fr']",10,"<p>Establishes the rated current, identification, test procedures and performance requirements for blade-type electric fuse-links with rated currents up to and including 30 A, used to protect on-board wiring harnesses and electrical equipment, with a rated voltage up to and including 32 V, of road vehicles and similar applica

28286,IS,,ISO 8820-1:2002,Road vehicles — Fuse-links — Part 1: Definitions and general test requirements,Véhicules routiers — Liaisons fusibles — Partie 1: Définitions et exigences générales d'essai,2002-06-13,2,['43.040.10'],ISO/TC 22,9599,[16270],[41936],"['en','fr']",8,"<p>This part of ISO 8820 defines terms and specifies general test requirements for low-voltage fuse-links with a rated voltage of 32 V and a breaking capacity of 1000 A intended for use in road vehicles at a nominal voltage of 12 V or 24 V. It establishes, for each fuse-link type, the characteristics, construction, operating conditions, marking and test conditions, so that an initial investigation of the fuse-link can be p

41936,IS,,ISO 8820-1:2008,Road vehicles — Fuse-links — Part 1: Definitions and general test requirements,Véhicules routiers — Liaisons fusibles — Partie 1: Définitions et exigences générales d'essai,2008-11-11,3,['43.040.10'],ISO/TC 22/SC 32,9599,[28286],[61777],['en'],10,"<p>ISO 8820-1:2008 defines terms and specifies general test requirements for fuse-links for electrical systems of road vehicles. </p><p>ISO 8820-1:2008 is intended to be used in conjunction with other parts of ISO 8820, to which its requirements are applicable except where modified by the particular requirements of another part.</p><p>ISO 8820-1:2008 is not applicable to fuse holders used in the vehicles.</p>"

62020,IS,,ISO 8820-10:2015,Road vehicles — Fuse-links — Part 10: Fuse-links with tabs Type L (high current miniature),Véhicules routiers — Liaisons fusibles — Partie 10: Liaisons fusibles à languette (type plat) type L (courant fort miniature),2015-03-16,1,['43.040.10'],ISO/TC 22/SC 32,9599,,"[77556,69415]",['en'],12,"<p>ISO 8820-10:2015 specifies fuse-links with tabs (blade type) Type L (high current miniature) for use in road vehicles. It establishes, for this fuse-link type, the rated current, test procedures, performance requirements, and dimensions.</p><p>ISO 8820-10:2015 is applicable for fuse-links with a rated voltage of 32 V, a current rating of ≤60 A, and a breaking capacity of 1 0

16271,IS,,ISO 8820-2:1994,Road vehicles — Blade-type electric fuse-links — Part 2: Dimensions,Véhicules routiers — Fusibles électriques plats — Partie 2: Dimensions,1994-07-28,1,['43.040.10'],ISO/TC 22,9599,,"[34258,27186]","['en','fr']",3,"<p>Establishes the requirements for the overall dimensions of blade-type electric fuse-links with rated currents up to and including 30 A, used to protect on-board wiring harnesses and electrical equipment, with a rated voltage up to and including 32 V, of road vehicles and similar applications from overcurrent. Interruption of the circuit is achieved as a result of the fuse element melting. Rated current, identification, test procedures and performance o

34258,IS,,ISO 8820-2:2005,Road vehicles — Fuse-links — Part 2: User's guide,Véhicules routiers — Liaisons fusibles — Partie 2: Guide de l'utilisateur,2005-04-15,2,['43.040.10'],ISO/TC 22,9599,[16271],[55050],"['en','fr']",11,<p>8820-2:2005 gives guidance for the choice and application of automotive fuse-links. It describes the various parameters which have to be taken into account when selecting fuse-links.</p><p>8820-2:2005 is intended to be used in conjunction with ISO 8820-1 and the other parts of ISO 8820.</p>

16272,IS,,ISO 8820-3:1994,Road vehicles — Blade-type electric fuse-links — Part 3: Test fixture,Véhicules routiers — Fusibles électriques plats — Partie 3: Module d'essai,1994-07-28,1,['43.040.10'],ISO/TC 22,9599,,[27186],"['en','fr']",7,"<p>Establishes the overall dimensions, materials, finish and coatings for the test fixture to perform electrical tests on blade-type electric fuse-links as specified in ISO 8820-1, for road vehicles. Rated current, identification, test procedures and performance of blade-type electric fuse-links are specified in ISO 8820-1, and dimensions in ISO 8820-2.</p>"

27186,IS,,ISO 8820-3:2002,Road vehicles — Fuse-links — Part 3: Fuse-links with tabs (blade type),Véhicules routiers — Liaisons fusibles — Partie 3: Liaisons fusibles à languette (type plat),2002-11-19,2,['43.040.10'],ISO/TC 22,9599,"[16272,16271]",[41910],"['en','fr']",15,"<p>ISO 8820-3:2002 specifies low-voltage fuse-links with tabs (blade type) for fuses in road vehicles. It establishes, for this fuse-link type, the rated current, test procedures, performance requirements and dimensions. It is applicable to those fuse-links with a rated voltage of 32 V, a current rating of less than or equal to 80 A and a breaking capacity of 1 000 A, intended for use in road vehicles at a nominal voltage

41910,IS,,ISO 8820-3:2010,"Road vehicles — Fuse-links — Part 3: Fuse-links with tabs (blade type) Type C (medium), Type E (high current) and Type F (miniature)","Véhicules routiers — Liaisons fusibles — Partie 3: Liaisons fusibles à languette (type plat) type C (moyen), type E (courant fort) et type F (miniature)",2010-05-21,3,['43.040.10'],ISO/TC 22/SC 32,9599,[27186],[58088],['en'],16,"<p>ISO 8820-3:2010 specifies fuse-links with tabs (blade-type) Type C (medium), Type E (high current) and Type F (miniature) for use in road vehicles. It establishes, for these fuse-link types, the rated current, test procedures, performance requirements and dimensions. </p><p>ISO 8820-3:2010 is applicable f

58088,IS,,ISO 8820-3:2015,"Road vehicles — Fuse-links — Part 3: Fuse-links with tabs (blade type) Type C (medium), Type E (high current) and Type F (miniature)","Véhicules routiers — Liaisons fusibles — Partie 3: Liaisons fusibles cavalier (Type à lame), Type C (moyen), Type E (courant élevé) et Type F (miniature)",2015-09-08,4,['43.040.10'],ISO/TC 22/SC 32,9599,[41910],"[69852,85282]",['en'],17,"<p>ISO 8820-3:2015 specifies fuse-links with tabs (blade-type) Type C (medium), Type E (high current), and Type F (miniature) for use in road vehicles. It establishes, for these fuse-link types, the rated current, test procedures, performance requirements, and dimensions.</p><p>ISO 8820-3:2015 is ap

28287,IS,,ISO 8820-4:2002,Road vehicles — Fuse-links — Part 4: Fuse-links with female contacts (type A) and bolt-in contacts (type B) and their test fixtures,Véhicules routiers — Liaisons fusibles — Partie 4: Liaisons fusibles avec contacts femelles (type A) et contacts boulonnés (type B) et leurs montages d'essai,2002-04-11,1,['43.040.10'],ISO/TC 22,9599,,[41911],"['en','fr']",17,

41911,IS,,ISO 8820-4:2010,Road vehicles — Fuse-links — Part 4: Fuse-links with female contacts (type A) and bolt-in contacts (type B) and their test fixtures,Véhicules routiers — Liaisons fusibles — Partie 4: Liaisons fusibles avec contacts femelles (type A) et contacts boulonnés (type B) et leurs montages d'essai,2010-12-03,2,['43.040.10'],ISO/TC 22/SC 32,9599,[28287],[64604],['en'],16,"<p>ISO 8820‑4:2010 specifies fuse-links with female contacts (type A) and bolt-in contacts (type B) for use in road vehicles. It establishes, for these fuse-link types, the rated current, test procedures, performance requirements and dimensions.</p><p>ISO 8820‑4:2010 is applicable to fuse-links with a rated

35381,IS,,ISO 8820-5:2007,Road vehicles — Fuse-links — Part 5: Fuse-links with axial terminals (Strip fuse-links) Types SF 30 and SF 51 and test fixtures,"Véhicules routiers — Liaisons fusibles — Partie 5: Liaisons fusibles avec languettes axiales (liaisons fusibles électriques) des types SF 30 et SF 51, et montages d'essai",2007-02-28,1,['43.040.10'],ISO/TC 22/SC 32,9599,,[61249],['en'],13,"<p>ISO 8820-5:2007 specifies fuse-links with axial terminals (Strip fuse-links) Type SF30 and SF51 and test fixtures for fuses in road vehicles. It establishes, for these fuse-link types, the rated current, test procedures, performance requirements and dimensions. </p><p>ISO 8820-5:2007 is applicable to

39053,IS,,ISO 8820-6:2007,Road vehicles — Fuse-links — Part 6: Single-bolt fuse-links,Véhicules routiers — Liaisons fusibles — Partie 6: Liaisons fusibles à poste singulier,2007-02-28,1,['43.040.10'],ISO/TC 22/SC 32,9599,,[71948],['en'],10,"<p>ISO 8820-6:2007 specifies single-bolt fuse-links in road vehicles. It establishes, for this fuse-link type, the rated current, test procedures, performance requirements and dimensions. </p><p>ISO 8820-6:2007 is applicable to those fuse-links with a rated voltage of 58 V, a current rating of u 300 A and a breaking capacity of 2 000 A intended for use in road vehicles at a nominal voltage of 12 V, 24 V and/or 42 V.</p>"

52434,IS,,ISO 8820-8:2012,Road vehicles — Fuse-links — Part 8: Fuse-links with bolt-in contacts (Type H and J) with rated voltage of 450 V,Véhicules routiers — Liaisons fusibles — Partie 8: Liaisons fusibles avec contacts boulonnés (type H et J) à tension nominale de 450 V,2012-07-25,1,['43.040.10'],ISO/TC 22/SC 32,9599,,[76591],['en'],12,"<p>ISO 8820-8:2012 specifies fuse-links with bolt-in contacts (Type H and J) and test fixtures for the fuse-links for use in road vehicles. It establishes, for these fuse-link types, the rated current, test procedures, performance requirements and dimensions.</p><p>ISO 8820-8:2012 is applicable to fuse-links with a rated voltage of 450 V d.c., a current ra

16273,IS,,ISO 8821:1989,Mechanical vibration — Balancing — Shaft and fitment key convention,Vibrations mécaniques — Équilibrage — Convention relative aux clavettes d'arbres et aux éléments rapportés,1989-05-18,1,['21.120.40'],ISO/TC 108/SC 2,9599,,[56564],"['en','fr']",12,<p>Is intended to provide compatibility of all balanced components so that when they are assembled they will meet the overall balance and/or vibration tolerance levels for that assembly.</p>

16274,IS,,ISO 8822:1988,Information processing systems — Open Systems Interconnection — Connection oriented presentation service definition,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Définition du service de présentation en mode connexion,1988-08-18,1,['35.100.60'],ISO/IEC JTC 1,9599,,[24365],"['en','fr']",30,

16276,IS,Amd,ISO 8822:1988/Amd 1:1991,Information processing systems — Open Systems Interconnection — Connection oriented presentation service definition — Amendment 1,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Définition du service de présentation en mode connexion — Amendement 1,1991-09-19,1,['35.100.60'],ISO/IEC JTC 1,9599,,[24365],"['en','fr']",4,

16279,IS,Amd,ISO 8822:1988/Amd 5:1992,Information processing systems — Open Systems Interconnection — Connection oriented presentation service definition — Amendment 5,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Définition du service de présentation en mode connexion — Amendement 5,1992-12-30,1,['35.100.60'],ISO/IEC JTC 1,9599,,[24365],['en'],1,

16280,IS,,ISO 8823:1988,Information processing systems — Open Systems Interconnection — Connection oriented presentation protocol specification,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Spécification du protocole de présentation en mode connexion,1988-08-18,1,['35.100.60'],ISO/IEC JTC 1,9599,,[24364],"['en','fr']",54,

16285,IS,Amd,ISO 8823:1988/Amd 5:1992,Information processing systems — Open Systems Interconnection — Connection oriented presentation protocol specification — Amendment 5,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Spécification du protocole de présentation en mode connexion — Amendement 5,1992-12-30,1,['35.100.60'],ISO/IEC JTC 1,9599,,[24364],['en'],3,

16287,IS,,ISO 8824:1987,Information processing systems — Open Systems Interconnection — Specification of Abstract Syntax Notation One (ASN.1),Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Spécification de la notation de syntaxe abstraite numéro 1 (ASN.1),1987-12-17,1,['35.100.60'],ISO/IEC JTC 1,9599,,[16288],['fr'],,

16293,IS,,ISO 8825:1987,Information processing systems — Open Systems Interconnection — Specification of Basic Encoding Rules for Abstract Syntax Notation ONE (ASN.1),Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Spécification des règles de codage de base pour la notation de syntaxe abstraite numéro 1 (ASN.1),1987-10-29,1,['35.100.60'],ISO/IEC JTC 1,9599,,[16294],"['en','fr']",,

16302,IS,,ISO 8828:1988,Implants for surgery — Guidance on care and handling of orthopaedic implants,Implants chirurgicaux — Principes directeurs pour l'entretien et la manipulation des implants orthopédiques,1988-10-20,1,['11.040.40'],ISO/TC 150,9599,,[59234],"['en','fr']",3,"<p>This standard gives guidance on the procedures for receiving, storing, transporting, handling, cleaning and sterilization of the implants in the clinical range. Guidance on cautions necessary for preparing implants for the use are also outlined. It does not apply to the implant manufacturer.</p>"

16303,IS,,ISO 8829:1990,Aerospace — Polytetrafluoroethylene (PTFE) hose assemblies — Test methods,Aéronautique et espace — Tuyauteries flexibles en polytétrafluoréthylène (PTFE) — Méthodes d'essai,1990-02-08,1,"['83.140.40','49.080']",ISO/TC 20/SC 10,9599,,[40693],"['en','fr']",11,"<p>Specifies procedures for flexible hose and hose assemblies used in fluid systems in the pressure and temperature ranges covered by pressure classes B, D and E, and temperature types I, II and III as specified in ISO 6771. Applies to the hose and the hose coupling. The tests and assembly requirements for the connecting and fittings are covered in the procurement specification. Is applicable when reference is mad

5271,IS,,ISO 883:1976,Indexable (throwaway) carbide inserts without fixation hole — Dimensions,"Plaquettes amovibles en carbures métalliques, sans trou de fixation — Dimensions",1976-12-01,2,['25.100.01'],ISO/TC 29,9599,,[5272],"['en','fr']",12,

5272,IS,,ISO 883:1985,"Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole — Dimensions","Plaquettes amovibles en métaux-durs (carbures métalliques) avec arrondi de pointe, sans trou de fixation — Dimensions",1985-07-18,3,['25.100.01'],ISO/TC 29/SC 9,9599,[5271],[62905],"['en','fr']",7,

16306,IS,,ISO 8831:1989,Information processing systems — Open Systems Interconnection — Job transfer and manipulation concepts and services,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Concepts et services pour le transfert et manipulation de travaux,1989-06-01,1,['35.100.70'],ISO/IEC JTC 1,9599,,[20425],['en'],78,

16307,IS,,ISO 8832:1989,Information processing systems — Open Systems Interconnection — Specification of the Basic Class Protocol for Job Transfer and Manipulation,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Spécifications du protocole de base pour le transfert et manipulation de travaux,1989-06-01,1,['35.100.70'],ISO/IEC JTC 1,9599,,[16308],['en'],62,

16312,IS,,ISO 8835-2:1993,Inhalational anaesthesia systems — Part 2: Anaesthetic circle breathing systems,Systèmes d'anesthésie par inhalation — Partie 2: Circuits respiratoires fermés d'anesthésie,1993-10-21,1,['11.040.10'],ISO/TC 121/SC 1,9599,,[25636],"['en','fr']",17,

25636,IS,,ISO 8835-2:1999,Inhalational anaesthesia systems — Part 2: Anaesthetic breathing systems for adults,Systèmes d'anesthésie par inhalation — Partie 2: Systèmes respiratoires d'anesthésie pour adultes,1999-05-06,2,['11.040.10'],ISO/TC 121/SC 1,9599,[16312],[41114],['en'],22,

41114,IS,,ISO 8835-2:2007,Inhalational anaesthesia systems — Part 2: Anaesthetic breathing systems,Systèmes d'anesthésie par inhalation — Partie 2: Systèmes respiratoires d'anesthésie,2007-08-13,3,['11.040.10'],ISO/TC 121/SC 1,9599,[25636],[51285],"['en','fr']",22,"<p>ISO 8835-2:2007 specifies requirements for anaesthetic breathing systems that are supplied either assembled by the manufacturer or for assembly by the user in accordance with the manufacturer's instructions.</p><p>ISO 8835-2:2007 also covers circle absorber assemblies, exhaust valves, inspiratory and expiratory valves and, in some designs, those parts of an anaesthetic breathing system that are incorporated within an inhalation

16313,IS,,ISO 8835-3:1997,Inhalational anaesthesia systems — Part 3: Anaesthetic gas scavenging systems — Transfer and receiving systems,Systèmes d'anesthésie par inhalation — Partie 3: Systèmes d'évacuation des gaz d'anesthésie — Systèmes de transfert et de réception,1997-01-22,1,['11.040.10'],ISO/TC 121/SC 1,9599,,[39199],['en'],16,<p>Specifies requirements for transfer and receiving systems of active anaesthetic gas scavenging systems (AGSS) intended to reduce the exposure of hospital personnel to anaesthetic gases and vapours.</p>

39199,IS,,ISO 8835-3:2007,Inhalational anaesthesia systems — Part 3: Transfer and receiving systems of active anaesthetic gas scavenging systems,Systèmes d'anesthésie par inhalation — Partie 3: Systèmes de transfert et de réception des systèmes d'évacuation des gaz d'anesthésie,2007-08-13,2,['11.040.10'],ISO/TC 121/SC 1,9599,[16313],[51285],"['en','fr']",23,<p>ISO 8835-3:2007 specifies requirements for transfer and receiving systems of active anaesthetic gas scavenging systems (active AGSSs) intended to reduce exposure of healthcare personnel to anaesthetic gases and vapours while providing patient protection (e.g. against excessive flow and pressure).</p><p>ISO 8835-3:2007 also specifies re

56123,IS,Amd,ISO 8835-3:2007/Amd 1:2010,Inhalational anaesthesia systems — Part 3: Transfer and receiving systems of active anaesthetic gas scavenging systems — Amendment 1,Systèmes d'anesthésie par inhalation — Partie 3: Systèmes de transfert et de réception des systèmes d'évacuation des gaz d'anesthésie — Amendement 1,2010-09-29,2,['11.040.10'],ISO/TC 121/SC 1,9599,,[51285],"['en','fr']",2,

35202,IS,,ISO 8835-4:2004,Inhalational anaesthesia systems — Part 4: Anaesthetic vapour delivery devices,Systèmes d'anesthésie par inhalation — Partie 4: Dispositifs d'administration de vapeur anesthésique,2004-06-03,1,['11.040.10'],ISO/TC 121/SC 1,9599,,[51285],"['en','fr']",18,"<p>For the purposes of ISO 8835-4:2004, the requirements in IEC 60601-1:1988, Clause 1 apply except as follows.</p><p><i>Addition</i>:</p><p>ISO 8835-4:2004 specifies particular requirements for the essential performance of anaesthetic vapour delivery devices (AVDDs), as defined in 3.1. ISO 8835-4:2004 is applicable to AVDDs which are a component of an anaesthetic system and are intended to be continuously operator-

35203,IS,,ISO 8835-5:2004,Inhalational anaesthesia systems — Part 5: Anaesthetic ventilators,Systèmes d'anesthésie par inhalation — Partie 5: Ventilateurs d'anesthésie,2004-05-12,1,['11.040.10'],ISO/TC 121/SC 1,9599,,[51285],"['en','fr']",16,"<p>ISO 8835-5:2004 specifies particular requirements for the essential performance of anaesthetic ventilators (as defined in 3.1). ISO 8835-5:2004 is applicable to anaesthetic ventilators which are always a component of an anaesthetic system and are intended to be continuously attended by an operator.</p><p>ISO 8835-5:2004 is not applicable to anaesthetic ventilators intended for use with flammable anaesthetics, as determined by Annex BB.</p><p>The requ

16314,IS,,ISO 8836:1988,Suction catheters for use in respiratory tract,Sondes d'aspiration pour les voies respiratoires,1988-12-15,1,['11.040.10'],ISO/TC 121/SC 2,9599,,[23578],"['en','fr']",8,

23578,IS,,ISO 8836:1997,Suction catheters for use in the respiratory tract,Sondes d'aspiration pour les voies respiratoires,1997-11-06,2,['11.040.10'],ISO/TC 121/SC 2,9599,[16314],[43013],['en'],12,

43013,IS,,ISO 8836:2007,Suction catheters for use in the respiratory tract,Sondes d'aspiration pour les voies respiratoires,2007-08-29,3,"['11.040.10','11.040.25']",ISO/TC 121/SC 2,9599,[23578],[59236],"['en','fr','ru']",11,"<p>ISO 8836:2007 specifies requirements for suction catheters made of plastic materials and intended for use in suction of the respiratory tract.</p><p>Specialized suction catheters, e.g. those with more than one lumen and suction catheters without a terminal orifice, are excluded from the scope of this International Standard.</p><p>Angled-tip suction catheters (e.g. Coudé catheters) and suction catheters with aspirator collectors are not considered to be specialized and

59236,IS,,ISO 8836:2014,Suction catheters for use in the respiratory tract,Sondes d'aspiration pour les voies respiratoires,2014-10-15,4,"['11.040.10','11.040.25']",ISO/TC 121/SC 2,9599,[43013],[73496],"['en','fr']",27,"<p>ISO 8836:2014 specifies requirements for suction catheters, including closed suction catheters, made of flexible materials and intended for use in suctioning of the respiratory tract.</p><p>Angled-tip suction catheters (e.g. Coudé catheters) and suction catheters with aspirator collectors are not considered to be specialized and are therefore included in the scope of ISO 8836:2014.</p>"

16316,IS,,ISO 8839:1986,"Mechanical properties of fasteners — Bolts, screws, studs and nuts made of non-ferrous metals","Caractéristiques mécaniques des éléments de fixation — Vis, goujons et écrous en métaux non ferreux",1986-12-11,1,"['21.060.10','21.060.20']",ISO/TC 2/SC 11,9599,,[46236],"['en','fr']",4,"<p>Specifies the mechanical properties of products: with nominal thread diameters from M 1,6 to M 39 inclusive, with metric ISO thread in accordance with ISO 261, made of copper and copper alloys or aluminium and aluminium alloys; it does not apply to products with special property requirements.</p>"

16317,IS,,ISO 8840:1987,Refractory materials — Determination of bulk density of granular materials (grain density),Matériaux réfractaires — Détermination de la masse volumique apparente des matériaux en grains (masse volumique des grains),1987-09-03,1,['81.080'],ISO/TC 33,9599,,"[78298,38366]","['en','fr']",5,"<p>Two methods for the determination of the bulk density of granular refractory materials (grain density) having a grain size larger than 2mm are specified. Method 1 (mercury method with vacuum) is intended as a referee method. Method 2 is the arrested water absorption method. The two methods may give different results. Any statement of the value of a bilk density shall therefore be ac

16320,IS,,ISO 8843:1991,Aircraft — Crimp-removable contacts for electrical connectors — Identification system,Aéronefs — Contacts à sertir amovibles pour connecteurs électriques — Système d'identification,1991-12-05,1,"['01.070','49.060']",ISO/TC 20/SC 1,9599,,[37435],"['en','fr']",2,"<p>The system specified consists of two colour bands around the external diameter of the crimp barrel and, for thermocouple contacts, of additional letters or of a colour point.</p>"

16323,IS,,ISO 8846:1990,Small craft — Electrical devices — Protection against ignition of surrounding flammable gases,Navires de plaisance — Équipements électriques — Protection contre l'inflammation des gaz inflammables environnants,1990-11-29,1,['47.080'],ISO/TC 188,9599,,[87197],"['en','fr']",7,<p>Describes test methods and requirements for the design of electrical devices to be used on small craft so that they may be operated in an explosive atmosphere without igniting surrounding flammable gases.</p>

16324,IS,,ISO 8847:1987,Small craft — Steering gear — Wire rope and pulley systems,Navires de plaisance — Appareils à gouverner — Systèmes à drosses et réas,1987-10-15,1,['47.080'],ISO/TC 188,9599,,[38439],"['en','fr']",3,"<p>Specifies the minimum level of requirements for construction, operation and installation of wire rope and pulley steering systems on sailing craft, with or without an auxiliary engine. Sets requirements for the design and construction of all components of a steering system from the wheel to, and including, the steering arm.</p>"