Withdrawn and superseded ISO standards — page 176 of 246

16069,IS,,ISO 8670-2:1991,Ostomy collection bags — Part 2: Determination of freedom from leakage,Poches de recueil pour stomie — Partie 2: Détermination de l'absence de fuites,1991-12-12,1,['11.180'],ISO/TC 173/SC 3,9599,,[20228],"['en','fr']",2,

16072,IS,,ISO 8672:1993,Air quality — Determination of the number concentration of airborne inorganic fibres by phase contrast optical microscopy — Membrane filter method,Qualité de l'air — Détermination de la concentration en nombre de fibres inorganiques en suspension dans l'air par microscopie optique en contraste de phase — Méthode du filtre à membrane,1993-01-28,1,['13.040.30'],ISO/TC 146/SC 2,9599,,[53413],"['en','fr']",25,"<p>The principle of the method specified is collecting a sample by drawing a measured quantity of air through a membrane filter by means of a battery-powered sampling pump, transforming the filter from an opaque membrane into a homogeneous optically transparent spec

16073,IS,,ISO 8673:1988,"Hexagon nuts, style 1, with metric fine pitch thread — Product grades A and B","Écrous hexagonaux, style 1, à filetage métrique à pas fin — Grades A et B",1988-04-21,1,['21.060.20'],ISO/TC 2,9599,,[26387],"['en','fr']",4,

26387,IS,,ISO 8673:1999,"Hexagon nuts, style 1, with metric fine pitch thread — Product grades A and B","Écrous hexagonaux, style 1, à filetage métrique à pas fin — Grades A et B",1999-08-26,2,['21.060.20'],ISO/TC 2/SC 12,9599,[16073],[61673],"['en','fr']",5,

61673,IS,,ISO 8673:2012,Hexagon regular nuts (style 1) with metric fine pitch thread — Product grades A and B,Écrous hexagonaux normaux (style 1) à filetage métrique à pas fin — Grades A et B,2012-12-14,3,['21.060.20'],ISO/TC 2/SC 12,9599,[26387],"[66082,75027]","['en','fr']",6,<p>ISO 8673:2012 specifies the geometry of hexagon nuts with nominal thread diameter from 8 mm up to and including 64 mm and the mechanical properties of hexagon regular nuts (style 1) with metric fine pitch thread in product grade A for nominal thread diameters 8 mm less than or equal to <i>D</i> less than or equal to 16 mm and in product grade B for nominal diameters 16 mm less than <i>D</i> less than or equal to 39

16074,IS,,ISO 8674:1988,"Hexagon nuts, style 2, with metric fine pitch thread — Product grades A and B","Écrous hexagonaux, style 2, à filetage métrique à pas fin — Grades A et B",1988-04-14,1,['21.060.20'],ISO/TC 2,9599,,[26388],"['en','fr']",3,

26388,IS,,ISO 8674:1999,"Hexagon nuts, style 2, with metric fine pitch thread — Product grades A and B","Écrous hexagonaux, style 2, à filetage métrique à pas fin — Grades A et B",1999-08-26,2,['21.060.20'],ISO/TC 2/SC 12,9599,[16074],[61674],"['en','fr']",5,

61674,IS,,ISO 8674:2012,Hexagon high nuts (style 2) with metric fine pitch thread — Product grades A and B,Écrous hexagonaux hauts (style 2) à filetage métrique à pas fin — Grades A et B,2012-12-14,3,['21.060.20'],ISO/TC 2/SC 12,9599,[26388],"[66081,75028]","['en','fr']",5,"<p>ISO 8674:2012 specifies the characteristics of hexagon high nuts (style 2) with metric fine pitch thread, with nominal thread diameters from 8 mm up to and including 36 mm, with product grade A for sizes <i>D </i>≤ 16 mm and product grade B for sizes <i>D</i> &gt; 16 mm.</p><p>Coarse thread hexagon nuts, style 2, according to ISO 4033 are intended to be the first choice.</p>"

16075,IS,,ISO 8675:1988,Hexagon thin nuts with metric fine pitch thread — Product grades A and B,Écrous bas hexagonaux à filetage métrique à pas fin — Grades A et B,1988-04-14,1,['21.060.20'],ISO/TC 2,9599,,[26389],"['en','fr']",4,

26389,IS,,ISO 8675:1999,Hexagon thin nuts (chamfered) with metric fine pitch thread — Product grades A and B,Écrous bas hexagonaux (chanfreinés) à filetage métrique à pas fin — Grades A et B,1999-09-02,2,['21.060.20'],ISO/TC 2/SC 12,9599,[16075],[61675],"['en','fr']",6,

61675,IS,,ISO 8675:2012,Hexagon thin nuts chamfered (style 0) with metric fine pitch thread — Product grades A and B,Écrous bas hexagonaux chanfreinés (style 0) à filetage métrique à pas fin — Grades A et B,2012-12-14,3,['21.060.20'],ISO/TC 2/SC 12,9599,[26389],"[75029,66080]","['en','fr']",5,"<p>ISO 8675:2012 specifies the characteristics of chamfered hexagon thin nuts (style 0), with metric fine pitch thread, with nominal thread diameters from 8 mm up to and including 64 mm, with product grade A for sizes <i>D</i> ≤ 16 mm and product grade B for sizes <i>D</i> &gt; 16 mm.</p>"

16076,IS,,ISO 8676:1988,Hexagon head screws with metric fine pitch thread — Product grades A and B,Vis à tête hexagonale à filetage métrique à pas fin entièrement filetées — Grades A et B,1988-09-22,1,['21.060.10'],ISO/TC 2,9599,,[26380],"['en','fr']",8,

26380,IS,,ISO 8676:1999,Hexagon head screws with metric fine pitch thread — Product grades A and B,Vis à tête hexagonale à filetage métrique à pas fin entièrement filetées — Grades A et B,1999-08-26,2,['21.060.10'],ISO/TC 2/SC 11,9599,[16076],[56453],"['en','fr']",12,

56453,IS,,ISO 8676:2011,Hexagon head screws with metric fine pitch thread — Product grades A and B,Vis à tête hexagonale à filetage métrique à pas fin entièrement filetées — Grades A et B,2011-04-01,3,['21.060.10'],ISO/TC 2/SC 11,9599,[26380],[72582],"['en','fr']",11,"<p>ISO 8676:2011 specifies the characteristics of hexagon head screws with metric fine pitch thread with nominal thread diameters, <i>d</i>, from 8 mm to 64 mm, of product grade A for nominal thread diameters, <i>d</i>, from 8 mm to 24 mm and nominal lengths, <i>l</i>, up to and including 10<i>d</i><i> </i>or 150 mm, whichever is the shorter, and of product grade B for nominal thread diameters, <i>d</i>, over 24 mm or nominal l

5251,IS,,ISO 868:1978,Plastics — Determination of indentation hardness by means of a durometer (Shore hardness),Plastiques — Détermination de la dureté par pénétration au moyen d'un duromètre (dureté Shore),1978-05-01,1,['83.080.01'],ISO/TC 61,9599,,[5252],"['en','fr']",3,

5252,IS,,ISO 868:1985,Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness),Plastiques et ébonite — Détermination de la dureté par pénétration au moyen d'un duromètre (dureté Shore),1985-09-26,2,['83.080.01'],ISO/TC 61/SC 2,9599,[5251],[34804],"['en','fr']",3,<p>Specification of a method for the determination of the indentation hardness by means of two types of durometers: Type A for softer materials and type B for harder materials. The method permits measurement either of the initial indentation or of the indentation after a specified time of recovery. This method is an empirical test and primarily intended for control purposes.</p>

16086,IS,,ISO 8686-1:1989,Cranes — Design principles for loads and load combinations — Part 1: General,Appareils de levage à charge suspendue — Principes de calcul des charges et des combinaisons de charge — Partie 1: Généralités,1989-11-16,1,['53.020.20'],ISO/TC 96/SC 10,9599,,[59417],"['en','fr']",28,"<p>Establishes general methods for calculating loads and principles to be used to select load combinations for proof of competence for the structural and mechanical components for cranes as defined in ISO 4306-1. Is based on rigid-body kinetic analysis and elasto-static analysis. Provides the general form, content and range of parameter values for more specific standards and also a framework

35970,IS,,ISO 8686-2:2004,Cranes — Design principles for loads and load combinations — Part 2: Mobile cranes,Appareils de levage à charge suspendue — Principes de calcul des charges et des combinaisons de charge — Partie 2: Grues mobiles,2004-09-01,1,['53.020.20'],ISO/TC 96/SC 6,9599,,[71572],"['en','fr']",17,"<p>ISO 8686-2:2004 applies the principles set forth in ISO 8686-1 to mobile cranes, as defined in ISO 4306-2, and presents loads and load combinations appropriate for use in proof-of-competence calculations for the steel structures of mobile cranes.</p><p>ISO 8686-2:2004 is applicable to mobile cranes used for normal service and to mobile cranes used for duty cycle service.</p><p>NOTE

2665,IS,,ISO 8686-3:1998,Cranes — Design principles for loads and load combinations — Part 3: Tower cranes,Appareils de levage à charge suspendue — Principes de calcul des charges et des combinaisons de charge — Partie 3: Grues à tour,1998-10-29,1,['53.020.20'],ISO/TC 96/SC 7,9599,,[66765],"['en','fr']",5,

16088,IS,,ISO 8686-5:1992,Cranes — Design principles for loads and load combinations — Part 5: Overhead travelling and portal bridge cranes,Appareils de levage à charge suspendue — Principes de calcul des charges et des combinaisons de charges — Partie 5: Ponts roulants et ponts portiques,1992-08-06,1,['53.020.20'],ISO/TC 96/SC 9,9599,,[68813],"['en','fr']",4,"<p>Establishes the application of ISO 8686-1 to overhead travelling and portal bridge cranes as defined in ISO 4306-1, and gives specific values for the factors to be used.</p>"

16094,IS,,ISO 8690:1988,Decontamination of radioactively contaminated surfaces — Method for testing and assessing the ease of decontamination,Décontamination des surfaces contaminées par radioactivité — Méthode d'essai et de détermination de l'aptitude à la décontamination,1988-07-28,1,['13.280'],ISO/TC 85/SC 2,9599,,[74178],"['en','fr']",19,"<p>Is designed to obtain data allowing the comparison of the ease of decontamination of different surface materials and can be used for comparative tests with any radionuclide in aqueous solution. Comparison is based on the mean residual pulse rates. In order to allow the general qualifications of a surface material as a single product, a method based o

74178,IS,,ISO 8690:2020,Measurement of radioactivity — Gamma ray and beta emitting radionuclides — Test method to assess the ease of decontamination of surface materials,Mesurage de la radioactivité — Radionucléides émetteurs gamma et bêta — Méthode d'essai pour évaluer l'aptitude à la décontamination des matériaux de surface,2020-09-01,2,['13.280'],ISO/TC 85/SC 2,9599,[16094],[86827],"['en','fr']",34,"<p>This document applies to the testing of surfaces that may become contaminated by radioactive materials.</p><p>The ease of decontamination is a property of a surface and an important criterion for selecting surface materials used in the nuclear industry, interim storage or disposal facilitie

16096,IS,,ISO 8692:1989,Water quality — Fresh water algal growth inhibition test with Scenedesmus subspicatus and Selenastrum capricornutum,Qualité de l'eau — Essai d'inhibition de la croissance des algues d'eau douce avec Scenedesmus subspicatus et Selenastrum capricornutum,1989-11-09,1,['13.060.70'],ISO/TC 147/SC 5,9599,,[29924],"['en','fr']",6,<p>Gives a method for the determination of the toxic effects of chemical compounds on the growth of planktonic freshwater algae. The test can be used for readily water-soluble substances which are not significantly degraded or eliminated from the test system.</p>

29924,IS,,ISO 8692:2004,Water quality — Freshwater algal growth inhibition test with unicellular green algae,Qualité de l'eau — Essai d'inhibition de la croissance des algues d'eau douce avec des algues vertes unicellulaires,2004-09-22,2,['13.060.70'],ISO/TC 147/SC 5,9599,[16096],[54150],"['en','fr']",15,"<p>ISO 8692:2004 specifies a method for the determination of the growth inhibition of unicellular green algae by substances and mixtures contained in water or by wastewater. The method is applicable for substances that are easily soluble in water.</p><p>With modifications to this method, as described in ISO 14442 and ISO 5667-16, the inhibitory effects of poorly soluble organic and inorgani

16097,IS,,ISO 8693:1987,Tools for moulding — Flat ejector pins,Outillage de moulage — Éjecteurs à lame,1987-08-20,1,['25.120.30'],ISO/TC 29/SC 8,9599,,[23315],"['en','fr']",2,

23315,IS,,ISO 8693:1998,Tools for moulding — Flat ejector pins,Outillage de moulage — Éjecteurs lames,1998-11-05,2,['25.120.30'],ISO/TC 29/SC 8,9599,[16097],[57876],"['en','fr']",6,

16098,IS,,ISO 8694:1987,Tools for moulding — Shouldered ejector pins,Outillage de moulage — Éjecteurs épaulés,1987-08-20,1,['25.120.30'],ISO/TC 29/SC 8,9599,,[24801],"['en','fr']",2,

24801,IS,,ISO 8694:1998,Tools for moulding — Shouldered ejector pins,Outillage de moulage — Éjecteurs épaulés,1998-07-02,2,['25.120.30'],ISO/TC 29/SC 8,9599,[16098],[57877],"['en','fr']",4,

16099,IS,,ISO 8695:1987,Tools for pressing — Punches — Nomenclature and terminology,Outillage de presse — Poinçons — Nomenclature et terminologie,1987-09-24,1,"['25.120.10','01.040.25']",ISO/TC 29/SC 8,9599,,[52941],"['en','fr']",8,

16109,IS,,ISO 8705:1991,Mopeds — Measurement method for location of centre of gravity,Cyclomoteurs — Méthode de mesure de l'emplacement du centre de gravité,1991-02-21,1,['43.140'],ISO/TC 22,9599,,[36705],"['en','fr']",5,<p>Concerns the stability of a moped as an important element of the active safety. The determination of the kinetic characteristics of the moped/rider combination is to be considered an important part of the design parameters of the vehicle itself. The test procedure described in ISO 8705 deals with one aspect of the kinetic characteristics (the determination of the centre of gravity). Other measuring methods can be used if it is demonstrated that their results are equivalen

16112,IS,,ISO 8709:1995,Mopeds — Brakes and braking devices — Tests and measurement methods,Cyclomoteurs — Freins et dispositifs de freinage — Méthodes d'essai et de mesure,1995-06-15,1,['43.140'],ISO/TC 22,9599,,[45868],"['en','fr']",14,"<p>Specifies tests and measurement methods for brakes and braking of mopeds with two or three wheels, as defined in ISO 3833, which are intended for use on public roads, in order to establish uniform worldwide test procedures for braking systems. Reference is made to 'L-category' vehicles. Does not cover mopeds which are controlled by a pedestrian; designed for the special use of handicapped persons. Sets out: static tests, dynamic tests (basic tests, wet b

30355,IS,Cor,ISO 8709:1995/Cor 1:1998,Mopeds — Brakes and braking devices — Tests and measurement methods — Technical Corrigendum 1,Cyclomoteurs — Freins et dispositifs de freinage — Méthodes d'essai et de mesure — Rectificatif technique 1,1998-05-21,1,['43.140'],ISO/TC 22,9599,,[45868],"['en','fr']",3,

5255,IS,,ISO 871:1980,Plastics — Determination of temperature of evolution of flammable gases (decomposition temperature) from a small sample of pulverized material,Plastiques — Détermination de la température d'émission de gaz inflammables (température de décomposition) d'un petit échantillon de matériau pulvérisé,1980-07-01,1,"['83.080.01','13.220.40']",ISO/TC 61/SC 4,9599,,[5256],"['en','fr']",3,

5256,IS,,ISO 871:1996,Plastics — Determination of ignition temperature using a hot-air furnace,Plastiques — Détermination de la température d'allumage au moyen d'un four à air chaud,1996-09-19,2,"['83.080.01','13.220.40']",ISO/TC 61/SC 4,9599,[5255],"[40775,36263]","['en','fr']",7,<p>Gives a laboratory method for determining the flash-ignition temperature and spontaneous-ignition temperature of plastics using a hot-air furnace. Does not give a direct measure of the combustability or rate of burning of plastics. Replaces the first edition.</p>

40775,IS,,ISO 871:2006,Plastics — Determination of ignition temperature using a hot-air furnace,Plastiques — Détermination de la température d'allumage au moyen d'un four à air chaud,2006-11-15,3,"['83.080.01','13.220.40']",ISO/TC 61/SC 4,9599,[5256],[79709],['en'],7,"<p>ISO 871:2006 specifies a laboratory method for determining the flash-ignition temperature and spontaneous-ignition temperature of plastics using a hot-air furnace. It is one of a number of methods in use for evaluating the reaction of plastics to the effects of ignition sources.</p><p>The method described does not give a direct measure of the combustibility or rate of burning of a material or any definition of the safe upper

16113,IS,,ISO 8710:1995,Motorcycles — Brakes and braking devices — Tests and measurement methods,Motocyles — Freins et dispositifs de freinage — Méthodes d'essai et de mesure,1995-08-10,1,['43.140'],ISO/TC 22,9599,,[50875],"['en','fr']",15,<p>Specifies tests and measurement methods for brakes and braking systems for motorcycles with two or three wheels which are intended for use on public roads. Supplies uniform worldwide test procedures for braking systems.</p>

33749,IS,,ISO 8713:2002,Electric road vehicles — Vocabulary,Véhicules routiers électriques — Vocabulaire,2002-06-06,1,"['43.120','01.040.43']",ISO/TC 22,9599,,[38307],"['en','fr']",13,"<p>This International Standard establishes a terminology for the components of electric road vehicles and related terms. It is not applicable to all vehicle parts, but concentrates primarily on defining those components and terms specific to electric road vehicles.</p>"

38307,IS,,ISO 8713:2005,Electric road vehicles — Vocabulary,Véhicules routiers électriques — Vocabulaire,2005-04-12,2,"['43.120','01.040.43']",ISO/TC 22,9599,[33749],[55745],"['en','fr']",16,"<p>ISO 8713:2005 establishes a vocabulary of terms used in International Standards generally in relation to electric road vehicles. It is not intended to give definitions of all parts within a vehicle, but focuses on terms specific to electric road vehicles.</p>"

34087,IS,,ISO 8714:2002,Electric road vehicles — Reference energy consumption and range — Test procedures for passenger cars and light commercial vehicles,Véhicules routiers électriques — Consommation d'énergie de référence et autonomie de référence — Modes opératoires d'essai pour voitures particulières et véhicules utilitaires légers,2002-11-08,1,['43.120'],ISO/TC 22/SC 37,9599,,[81395],"['en','fr']",25,<p>This International Standard specifies test procedures for measuring the reference energy consumption and reference range of purely electrically propelled passenger cars and commercial vehicles of a maximum authorized total mass of 3 500 kg and maximum speed greater than or equal to 70 km

16118,IS,,ISO 8715:2001,Electric road vehicles — Road operating characteristics,Véhicules routiers électriques — Caractéristiques routières,2001-06-28,1,['43.120'],ISO/TC 22,9599,,[90693],"['en','fr']",17,"<p>This International Standard specifies the procedures for measuring the road performance of purely electrically</p><p>propelled passenger cars and commercial vehicles of a maximum authorized total mass of 3 500 kg1_.</p><p>The road performance comprises road operating characteristics such as speed, acceleration and hill climbing ability.</p>"

16119,IS,,ISO 8716:1988,Commercial road vehicles — Fifth wheel coupling pins — Strength tests,Véhicules routiers utilitaires — Pivot d'attelage — Essais de résistance,1988-10-06,1,['43.040.70'],ISO/TC 22,9599,,[34024],"['en','fr']",2,"<p>Establishes test conditions and strength requirements to be met by 50 and 90 fifth wheel coupling pins. Gives the equation to be used to calculate the F_hvalue (expressed in kN), shows the application of test load (figure 1), and describes the loading cycle and the selected frequency as well as strength criteria.</p>"

16120,IS,,ISO 8717:1988,Commercial road vehicles — Fifth wheel couplings — Strength tests,Véhicules routiers utilitaires — Sellettes d'attelage — Essais de résistance,1988-06-23,1,['43.040.70'],ISO/TC 22,9599,,[23028],"['en','fr']",3,

16121,IS,,ISO 8718:1988,Commercial road vehicles — Drawbar couplings and eyes for hinged drawbars — Strength test,Véhicules routiers utilitaires — Pivots et anneaux pour barres d'attelage articulées — Essai de résistance,1988-10-20,1,['43.040.70'],ISO/TC 22,9599,,[34025],"['en','fr']",2,"<p>Establishes test conditions and strength requirements to be met by 40 mm and 50 mm drawbar couplings, and the corresponding drawbar eyes. Gives the equation to be used to calculate the F-value (expressed in kN), shows the application of horizontal test load (figure 1), and describes the loading cycle and the selected frequency as well as strength criteria.</p>"

16124,IS,,ISO 8721:1987,Road vehicles — Measurement techniques in impact tests — Optical instrumentation,Véhicules routiers — Techniques de mesurage lors des essais de chocs — Instrumentation optique,1987-09-24,1,['43.020'],ISO/TC 22,9599,,[46279],"['en','fr']",3,"<p>Defines performance criteria for an optical data channel used in impact tests on road vehicles, when numerical time and space data are taken from the images to analyse impact test results. The requirements are to facilitate comparison between results obtained by different laboratories.</p>"

46279,IS,,ISO 8721:2010,Road vehicles — Measurement techniques in impact tests — Optical instrumentation,Véhicules routiers — Techniques de mesure lors des essais de chocs — Instrumentation optique,2010-09-03,2,['43.020'],ISO/TC 22/SC 36,9599,[16124],[72232],['en'],47,"<p>ISO 8721:2010 defines performance criteria for an optical data channel used in impact tests on road vehicles, when numerical time and space data are taken from images to analyse impact test results.</p><p>The objective of ISO 8721:2010 is to facilitate comparison between results obtained by different laboratories by specifying minimum quality criteria.</p>"

16127,IS,,ISO 8724:1989,Cork decorative panels — Specification,Panneaux décoratifs à base de liège — Spécifications,1989-06-29,1,['79.100'],ISO/TC 87,9599,,[44780],"['en','fr']",3,"<p>Applies to panels intended for covering internal walls which may be grouped into five classes according to their constitution (siehe ISO 633). Specifies the following characteristics: dimensions, squareness and straightness of edges, moisture content, handling behaviour, resistance to boiling water and resistance of glued joint which shall in the classes IV and V not show any unglueing when tested in accordance with Annex A.</p>"

16131,IS,,ISO 8728:1987,Shipbuilding — Marine gyro-compasses,Construction navale — Compas gyroscopiques à usage marin,1987-09-03,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[16132],"['en','fr']",6,

16132,IS,,ISO 8728:1997,Ships and marine technology — Marine gyro-compasses,Navires et technologie maritime — Compas gyroscopiques à usage marin,1997-06-19,2,['47.020.70'],ISO/TC 8/SC 6,9599,[16131],[62176],"['en','fr']",10,

62176,IS,,ISO 8728:2014,Ships and marine technology — Marine gyro-compasses,Navires et technologie maritime — Compas gyroscopiques à usage marin,2014-07-25,3,['47.020.70'],ISO/TC 8/SC 6,9599,[16132],[82079],['en'],14,"<p>ISO 8728:2014 specifies the construction, performance, and type testing for gyro-compasses required by Regulation 12 of Chapter V of SOLAS 1974 (as amended).</p>"

16133,IS,,ISO 8729:1987,Shipbuilding — Marine radar reflectors,Construction navale — Réflecteurs radars de marine,1987-10-15,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[16134],['en'],6,

16134,IS,,ISO 8729:1997,Ships and marine technology — Marine radar reflectors,Navires et technologie maritime — Réflecteurs radars de marine,1997-06-19,2,['47.020.70'],ISO/TC 8/SC 6,9599,[16133],[51331],"['en','fr']",7,

16135,IS,,ISO 8730:1986,Banking — Requirements for message authentication (wholesale),Opérations bancaires — Spécifications liées à la normalisation de l'authentification des messages,1986-11-13,1,['35.240.40'],ISO/TC 68/SC 2,9599,,[16136],"['en','fr']",,

16136,IS,,ISO 8730:1990,Banking — Requirements for message authentication (wholesale),Opérations bancaires — Spécifications liées à l'authentification des messages (service aux entreprises),1990-05-24,2,['35.240.40'],ISO/TC 68/SC 2,9599,[16135],[30381],"['en','fr']",25,<p>Operation implies acceptance of the responsibility for their MAC (message authentication code) by the correspondent financial institutions. Specifies the method by which authentication algorithms are to be approved for inclusion in ISO 8731. It specifies a technique for protecting either the whole of the message or specified elements within it. The authentication of messages is independent of the transmission process used.

33170,IS,Cor,ISO 8730:1990/Cor 1:1999,Banking — Requirements for message authentication (wholesale) — Technical Corrigendum 1: .,Opérations bancaires — Spécifications liées à l'authentification des messages (service aux entreprises) — Rectificatif technique 1: .,1999-12-16,2,['35.240.40'],ISO/TC 68/SC 2,9599,,[30381],"['en','fr']",1,

16137,IS,,ISO 8731-1:1987,Banking — Approved algorithms for message authentication — Part 1: DEA,Banque — Algorithmes approuvés pour l'authentification des messages — Partie 1: DEA,1987-05-21,1,['35.240.40'],ISO/TC 68/SC 2,9599,,[30381],"['en','fr']",2,<p>This part ISO 8731 deals with the Data Encryption Algorithm (DEA) as a method for use in the calculation of the Message Authentication Code (MAC). It meets the requirements specified in ISO 8730.</p>

16138,IS,,ISO 8731-2:1987,Banking — Approved algorithm for message authentication — Part 2: Message authenticator algorithms,Banque — Algorithmes approuvés pour l'authentification des messages — Partie 2: Algorithme d'authentification des messages,1987-12-17,1,['35.240.40'],ISO/TC 68/SC 2,9599,,[16139],"['en','fr']",8,

16139,IS,,ISO 8731-2:1992,Banking — Approved algorithms for message authentication — Part 2: Message authenticator algorithm,Banque — Algorithmes approuvés pour l'authentification des messages — Partie 2: Algorithme authentificateur de message,1992-09-03,2,['35.240.40'],ISO/TC 68/SC 2,9599,[16138],"[30515,30381]","['en','fr']",19,"<p>The algorithm described is specifically designed for high-speed authentication using a mainframe computer. It is also suitable for use with a programmable calculator. It works on the principle of a Message Authentication Code (MAC), a number sent with a message, so that a check can be made by the receiver of the message that it has not been altered since it left

16142,IS,,ISO 8733:1986,"Parallel pins with internal thread, unhardened","Goupilles cylindriques à trou taraudé, non trempées",1986-10-23,1,['21.060.50'],ISO/TC 2,9599,,[21793],"['en','fr']",3,

16143,IS,,ISO 8734:1987,"Parallel pins, hardened (Dowel pins)",Goupilles cylindriques trempées,1987-11-19,1,['21.060.50'],ISO/TC 2,9599,,[20002],"['en','fr']",3,

16144,IS,,ISO 8735:1987,"Parallel pins with internal thread, hardened","Goupilles cylindriques à trou taraudé, trempées",1987-10-22,1,['21.060.50'],ISO/TC 2,9599,,[21794],"['en','fr']",4,

16148,IS,,ISO 8739:1986,"Grooved pins — Full-length parallel grooved, with pilot","Goupilles cannelées à cannelures constantes sur toute la longueur débouchantes, à bout pilote",1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20003],"['en','fr']",3,

20003,IS,,ISO 8739:1997,"Grooved pins — Full-length parallel grooved, with pilot","Goupilles cannelées à cannelures constantes sur toute la longueur débouchantes, à bout pilote",1997-10-30,2,['21.060.50'],ISO/TC 2,9599,[16148],"[77711,84081]","['en','fr']",3,

16149,IS,,ISO 8740:1986,"Grooved pins — Full length parallel grooved, with chamfer","Goupilles cannelées à cannelures constantes sur toute la longueur débouchantes, à chanfrein",1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20006],"['en','fr']",3,

20006,IS,,ISO 8740:1997,"Grooved pins — Full-length parallel grooved, with chamfer","Goupilles cannelées à cannelures constantes sur toute la longueur débouchantes, à chanfrein",1997-10-30,2,['21.060.50'],ISO/TC 2,9599,[16149],"[77712,84083]","['en','fr']",3,

16150,IS,,ISO 8741:1986,Grooved pins — Half-length reverse taper grooved,Goupilles cannelées à cannelures progressives renversées sur la moitié de la longueur non débouchantes,1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20007],"['en','fr']",3,

20007,IS,,ISO 8741:1997,Grooved pins — Half-length reverse-taper grooved,Goupilles cannelées à cannelures progressives renversées sur la moitié de la longueur non débouchantes,1997-10-30,2,['21.060.50'],ISO/TC 2,9599,[16150],"[84096,77713]","['en','fr']",3,

16151,IS,,ISO 8742:1986,Grooved pins — Third-length centre grooved,Goupilles cannelées à cannelures centrales constantes sur le tiers de la longueur non débouchantes,1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20008],"['en','fr']",3,

20008,IS,,ISO 8742:1997,Grooved pins — One-third-length centre grooved,Goupilles cannelées à cannelures centrales constantes sur le tiers de la longueur non débouchantes,1997-10-30,2,['21.060.50'],ISO/TC 2,9599,[16151],"[77715,84097,90788]","['en','fr']",3,

16152,IS,,ISO 8743:1986,Grooved pins — Half-length centre grooved,Goupilles cannelées à cannelures centrales constantes sur la moitié de la longueur non débouchantes,1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20009],"['en','fr']",3,

20009,IS,,ISO 8743:1997,Grooved pins — Half-length centre grooved,Goupilles cannelées à cannelures centrales constantes sur la moitié de la longueur non débouchantes,1997-10-30,2,['21.060.50'],ISO/TC 2,9599,[16152],"[90789,77716,84098]","['en','fr']",3,

16153,IS,,ISO 8744:1986,Grooved pins — Full-length taper grooved,Goupilles cannelées à cannelures progressives sur toute la longueur (débouchantes),1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20010],"['en','fr']",3,

20010,IS,,ISO 8744:1997,Grooved pins — Full-length taper grooved,Goupilles cannelées à cannelures progressives sur toute la longueur (débouchantes),1997-10-30,2,['21.060.50'],ISO/TC 2,9599,[16153],"[84100,77717]","['en','fr']",3,

16154,IS,,ISO 8745:1986,Grooved pins — Half-length taper grooved,Goupilles cannelées à cannelures progressives sur la moitié de la longueur (débouchantes),1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20013],"['en','fr']",3,

20013,IS,,ISO 8745:1997,Grooved pins — Half-length taper grooved,Goupilles cannelées à cannelures progressives sur la moitié de la longueur (débouchantes),1997-11-06,2,['21.060.50'],ISO/TC 2,9599,[16154],"[84101,77718]","['en','fr']",3,

16155,IS,,ISO 8746:1986,Grooved pins with round head,Clous cannelés à tête ronde,1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20014],"['en','fr']",3,

20014,IS,,ISO 8746:1997,Grooved pins with round head,Clous cannelés à tête ronde,1997-11-06,2,['21.060.50'],ISO/TC 2,9599,[16155],"[77719,84102]","['en','fr']",4,

16156,IS,,ISO 8747:1986,Grooved pins with countersunk head,Clous cannelés à tête fraisée,1986-11-06,1,['21.060.50'],ISO/TC 2,9599,,[20015],"['en','fr']",3,

20015,IS,,ISO 8747:1997,Grooved pins with countersunk head,Clous cannelés à tête fraisée,1997-11-06,2,['21.060.50'],ISO/TC 2,9599,[16156],"[84103,77720]","['en','fr']",4,

16157,IS,,ISO 8748:1987,"Spring-type straight pins — Coiled, heavy duty",Goupilles élastiques spiralées — Série épaisse,1987-11-19,1,['21.060.50'],ISO/TC 2,9599,,[20016],"['en','fr']",3,

20016,IS,,ISO 8748:1997,"Spring-type straight pins — Coiled, heavy duty",Goupilles élastiques spiralées — Série épaisse,1997-11-06,2,['21.060.50'],ISO/TC 2,9599,[16157],[40661],"['en','fr']",5,

5260,IS,,ISO 875:1981,Essential oils — Evaluation of miscibility in ethanol,Huiles essentielles — Évaluation de la miscibilité à l'éthanol,1981-07-01,1,['71.100.60'],ISO/TC 54,9599,,[25312],"['en','fr']",3,

16159,IS,,ISO 8750:1987,"Spring-type straight pins — Coiled, standard duty",Goupilles élastiques spiralées — Série moyenne,1987-11-19,1,['21.060.50'],ISO/TC 2,9599,,[20017],"['en','fr']",3,

20017,IS,,ISO 8750:1997,"Spring-type straight pins — Coiled, standard duty",Goupilles élastiques spiralées — Série moyenne,1997-11-20,2,['21.060.50'],ISO/TC 2,9599,[16159],[40660],"['en','fr']",5,

16160,IS,,ISO 8751:1987,"Spring-type straight pins — Coiled, light duty",Goupilles élastiques spiralées — Série mince,1987-11-19,1,['21.060.50'],ISO/TC 2,9599,,[20019],['en'],3,

20019,IS,,ISO 8751:1997,"Spring-type straight pins — Coiled, light duty",Goupilles élastiques spiralées — Série mince,1997-11-20,2,['21.060.50'],ISO/TC 2,9599,[16160],[40659],"['en','fr']",5,

16161,IS,,ISO 8752:1987,"Spring-type straight pins, slotted","Goupilles cylindriques creuses, dites goupilles élastiques",1987-11-05,1,['21.060.50'],ISO/TC 2,9599,,[20020],"['en','fr']",4,

20020,IS,,ISO 8752:1997,"Spring-type straight pins — Slotted, heavy duty","Goupilles cylindriques creuses, dites goupilles élastiques — Série épaisse",1997-11-20,2,['21.060.50'],ISO/TC 2,9599,[16161],[40658],"['en','fr']",6,

16162,IS,,ISO 8753:1987,Iron ores — Determination of lead and/or zinc content — Flame atomic absorption spectrometric method,Minerais de fer — Dosage du plomb et/ou du zinc — Méthode par spectrométrie d'absorption atomique dans la flamme,1987-05-07,1,['73.060.10'],ISO/TC 102/SC 2,9599,,"[21680,21681]","['en','fr']",10,

16163,IS,,ISO 8754:1992,Petroleum products — Determination of sulfur content — Energy-dispersive X-ray fluorescence method,Produits pétroliers — Détermination de la teneur en soufre — Méthode par spectrométrie de fluorescence X dispersive en énergie,1992-05-07,1,['75.080'],ISO/TC 28,9599,,[30062],"['en','fr']",3,"<p>The method specified for the determination of the sulfur content of hydrocarbons is applicable to products having sulfur contents in the range 0,01 % (m/m) to 5 % (m/m). Samples containing heavy-metal additives interfere with the method. Elements such as silicon, phosphorus, calcium, potassium and halides interfere if present in concentrations of more than a few hundred milligram

30062,IS,,ISO 8754:2003,Petroleum products — Determination of sulfur content — Energy-dispersive X-ray fluorescence spectrometry,Produits pétroliers — Détermination de la teneur en soufre — Spectrométrie de fluorescence de rayons X dispersive en énergie,2003-07-25,2,['75.080'],ISO/TC 28,9599,[16163],[83051],"['en','fr']",7,"<div id='MathJax_Message' style='display: none;'></div><p>ISO 8754:2003 specifies a method for the determination of the sulfur content of petroleum products, such as naphthas, unleaded motor gasolines, middle distillates, residual fuel oils, base lubricating oils and components. The method is applicable to products having sulfur contents in the range 0,03 % (by mass) to 5

16164,IS,,ISO 8755:1986,Commercial road vehicles — Mechanical connections between towing vehicles and trailers — 40 mm drawbar coupling,Véhicules routiers utilitaires — Liaisons mécaniques entre véhicules tracteurs et remorques — Dispositifs d'attelage de 40 mm,1986-12-18,1,['43.040.70'],ISO/TC 22,9599,,"[30353,20556]","['en','fr']",5,"<p>Specifies the essential dimensions of a 40 mm drawbar coupling and a 40 mm drawbar eye to permit interchangeability between towing vehicles and trailers equipped with these connections. These connections are not interchangeable with the 50 mm couplings specified in ISO 1102. Applies to connections designed for commercial vehicles and trailers, the maximum t

16168,IS,,ISO 8759-1:1985,Agricultural wheeled tractors — Front-mounted linkage and power take-off — Part 1: Power take-off,Tracteurs agricoles à roues — Attelage et prise de force montés à l'avant — Partie 1: Prise de force,1985-12-12,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[21073],"['en','fr']",1,

21073,IS,,ISO 8759-1:1998,Agricultural wheeled tractors — Front-mounted equipment — Part 1: Power take-off and three- point linkage,Tracteurs agricoles à roues — Équipement monté à l'avant — Partie 1: Prise de force et attelage trois points,1998-03-19,2,['65.060.10'],ISO/TC 23/SC 4,9599,"[16168,16169]","[68671,69784,69785,69783,62219]","['en','fr']",5,

16169,IS,,ISO 8759-2:1985,Agricultural wheeled tractors — Front-mounted linkage and power take-off — Part 2: Front linkage,Tracteurs agricoles à roues — Attelage et prise de force montés à l'avant — Partie 2: Attelage avant,1985-11-14,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[21073],"['en','fr']",4,

16175,IS,,ISO 8764-1:1992,Screwdrivers for cross-recessed head screws — Part 1: Driver points,Tournevis pour vis à empreinte cruciforme — Partie 1: Extrémités de tournevis,1992-11-25,1,['25.140.30'],ISO/TC 29/SC 10,9599,[16174],[27267],"['en','fr']",9,

27267,IS,,ISO 8764-1:1999,Assembly tools for screws and nuts — Screwdrivers for cross-recessed head screws — Part 1: Driver points,Outils de manoeuvre pour vis et écrous — Tournevis pour vis à empreinte cruciforme — Partie 1: Extrémités de tournevis,1999-09-30,2,['25.140.30'],ISO/TC 29/SC 10,9599,[16175],[37562],"['en','fr']",21,

16174,IS,,ISO 8764:1989,Driver points to fit cross-recessed head screws,Extrémités de tournevis pour vis à empreinte cruciforme,1989-09-07,1,['25.140.30'],ISO/TC 29/SC 10,9599,,[16175],"['en','fr']",9,

16176,IS,,ISO 8764-2:1992,"Screwdrivers for cross-recessed head screws — Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers","Tournevis pour vis à empreinte cruciforme — Partie 2: Spécifications générales, longueurs des lames et marquage des tournevis à main",1992-11-19,1,['25.140.30'],ISO/TC 29/SC 10,9599,,[37556],"['en','fr']",3,<p>The requirements and marking specified apply to screwdrivers for H and Z cross-recessed head screws. Requirements for blade tips are given in ISO 8764-1.</p>

16177,IS,,ISO 8765:1988,Hexagon head bolts with metric fine pitch thread — Product grades A and B,Vis à tête hexagonale à filetage métrique à pas fin partiellement filetées — Grades A et B,1988-06-02,1,['21.060.10'],ISO/TC 2,9599,,[26381],"['en','fr']",8,

26381,IS,,ISO 8765:1999,Hexagon head bolts with metric fine pitch thread — Product grades A and B,Vis à tête hexagonale à filetage métrique à pas fin partiellement filetées — Grades A et B,1999-09-09,2,['21.060.10'],ISO/TC 2/SC 11,9599,[16177],[56454],"['en','fr']",12,