Withdrawn and superseded ISO standards — page 178 of 246

38439,IS,,ISO 8847:2004,Small craft — Steering gear — Cable and pulley systems,Petits navires — Appareils à gouverner — Systèmes à drosses et réas,2004-04-30,2,['47.080'],ISO/TC 188,9599,[16324],[75809],"['en','fr']",7,"<p>ISO 8847:2004 specifies the minimum level of requirements for operation, construction and installation of cable and pulley steering systems on sailing craft of hull length up to 24 m , with or without an auxiliary engine.</p><p>ISO 8847:2004 sets requirements for the design and construction of all components of a steering system from the wheel to, and including, the steering arm. It applies only to cable and pulley steering systems, whether for pedestal or bulkhead types.

16325,IS,,ISO 8848:1990,Small craft — Remote steering systems,Navires de plaisance — Appareils à gouverner commandés à distance,1990-12-20,1,['47.080'],ISO/TC 188,9599,,"[75540,75467]","['en','fr']",9,"<p>Lays down requirements and test methods for remote push-pull cable steering systems and their major component items, used for small craft with single and twin installations of outboard motors of over 15 kW power, and all inboard motors, inboard motor-outdrives, and waterjet drives.</p>"

75540,IS,,ISO 8848:2020,Small craft — Remote mechanical steering systems,Petits navires — Appareils à gouverner commandés à distance,2020-12-14,2,['47.080'],ISO/TC 188,9599,"[16325,17637,28595]",[83512],"['en','fr']",21,"<p>This document specifies design, construction, installation and test requirements for remote mechanical cable steering systems and the output ram interface point to rudders, jet drives, outboard and sterndrive engines for small craft.</p><p>It is applicable to three distinct classes of steering systems for use on various types of craft:</p><p>— standard duty steering systems, for small craft with single and twin installations of outboard engines with a total over 15 kW

16326,IS,,ISO 8849:1990,Small craft — Electrically operated bilge-pumps,Navires de plaisance — Pompes de cale à moteur électrique,1990-12-13,1,['47.080'],ISO/TC 188,9599,,[34174],"['en','fr']",2,<p>Specifies requirements for electrically operated pumps intended for use in removing bilge-water from small craft. Applies to electrically operated bilge-pumps rated for less than 50 V d.c.</p>

34174,IS,,ISO 8849:2003,Small craft — Electrically operated direct-current bilge pumps,Petits navires — Pompes de cale à moteur électrique en courant continu,2003-10-14,2,['47.080'],ISO/TC 188,9599,[16326],[72107],"['en','fr']",3,<p>ISO 8849:2003 specifies requirements for electrically operated direct-current bilge pumps intended for use in removing bilge water from small craft with a hull length up to 24 m. It applies to electrically operated bilge pumps rated for less than 50 V direct current (d.c.). It does not cover pumps intended for damage control.</p>

5274,IS,,ISO 885:1976,General purpose bolts and screws — Metric series — Radii under the head,Boulons et vis d'application générale — Série métrique — Rayon d'arrondi sous tête,1976-05-01,1,['21.060.10'],ISO/TC 2/SC 7,9599,,[32402],"['en','fr']",1,

16331,IS,,ISO 8854:1988,Road vehicles — Alternators with regulators — Test methods and general requirements,Véhicules routiers — Alternateurs avec régulateur — Méthodes d'essai et conditions générales,1988-01-21,1,['43.060.50'],ISO/TC 22,9599,,[55075],"['en','fr']",4,"<p>Specifies test methods and general requirements for the determination of the electrical characteristic data of alternators for road vehicles. Applies to alternators, cooled according to the manufacturer's instructions, mounted on internal combustion engines. Figure 1 shows a diagram for alternator testing.</p>"

16332,IS,,ISO 8855:1991,Road vehicles — Vehicle dynamics and road-holding ability — Vocabulary,Véhicules routiers — Dynamique des véhicules et tenue de route — Vocabulaire,1991-12-16,1,"['43.020','01.040.43']",ISO/TC 22,9599,,"[37216,51180]","['en','fr']",22,<p>Specifies 129 terms and definitions in English and French. Contains the alphabetical indexes in English and French. Annexes A and B are for information only.</p>

16333,IS,Add,ISO 8855:1991/Add 1:1992,Road vehicles — Vehicle dynamics and road-holding ability — Vocabulary — Addendum 1: Russian language version,Véhicules routiers — Dynamique des véhicules et tenue de route — Vocabulaire — Additif 1: Version en langue russe,1992-10-01,1,"['43.020','01.040.43']",ISO/TC 22,9599,,"[37216,51180]",['ru'],,

16334,IS,,ISO 8856:1988,Road vehicles — Starter motors — Test methods and general requirements,Véhicules routiers — Démarreurs — Méthodes d'essai et conditions générales,1988-01-21,1,['43.060.50'],ISO/TC 22,9599,,[16335],"['en','fr']",5,

16335,IS,,ISO 8856:1995,Road vehicles — Electrical performance of starter motors — Test methods and general requirements,Véhicules routiers — Caractéristiques électriques des démarreurs — Méthodes d'essai et conditions générales,1995-11-16,2,['43.060.50'],ISO/TC 22,9599,[16334],[61337],"['en','fr']",9,<p>Lays down test methods and general requirements for the determination of the electrical characteristics of d.c. starter motors intended to start internal combustion engines of road vehicles.</p>

28431,IS,Amd,ISO 8856:1995/Amd 1:1997,Road vehicles — Electrical performance of starter motors — Test methods and general requirements — Amendment 1,Véhicules routiers — Caractéristiques électriques des démarreurs — Méthodes d'essai et conditions générales — Amendement 1,1997-12-25,2,['43.060.50'],ISO/TC 22,9599,,[61337],"['en','fr']",1,

16337,IS,,ISO 8858-1:1990,Hard coal — Froth flotation testing — Part 1: Laboratory procedure,Houille — Essais de flottation — Partie 1: Méthode de laboratoire,1990-08-30,1,['73.040'],ISO/TC 27/SC 1,9599,,[75885],['en'],10,

34889,IS,Cor,ISO 8858-1:1990/Cor 1:2001,Hard coal — Froth flotation testing — Part 1: Laboratory procedure — Technical Corrigendum 1,Houille — Essais de flottation — Partie 1: Méthode de laboratoire — Rectificatif technique 1,2001-04-12,1,['73.040'],ISO/TC 27/SC 1,9599,,[75885],['en'],1,

34310,IS,,ISO 8858-2:2004,Hard coal — Froth flotation testing — Part 2: Sequential evaluation,Houille — Essais de flottation — Partie 2: Évaluation séquentielle,2004-08-05,1,['73.040'],ISO/TC 27/SC 1,9599,,[87992],['en'],13,"<p>ISO 8858-2:2004 sets out a laboratory sequential procedure for the froth flotation testing of fine coal, e.g. coal having a particle size of less than 0,5 mm. The procedure provides a means of evaluating for a coal the flotation characteristics (expressed as a yield/ash relationship) that may be expected from the froth flotation process.</p><p>Pulp samples that cannot be dewatered without the use of heat or chemical additives are not covered by this part of ISO 8858;

34311,IS,,ISO 8858-3:2004,Hard coal — Froth flotation testing — Part 3: Release evaluation,Houille — Essais de flottation — Partie 3: Évaluation des émissions,2004-08-09,1,['73.040'],ISO/TC 27/SC 1,9599,,[87993],['en'],9,"<p>ISO 8858-3:2004 describes a laboratory method for release evaluation of the froth flotation characteristics of hard coal, of particle size less than 0.5 mm. It is applicable to coal in powder form or in the form of a slurry.</p>"

16338,IS,,ISO 8859-1:1987,Information processing — 8-bit single-byte coded graphic character sets — Part 1: Latin alphabet No. 1,Traitement de l'information — Jeux de caractères graphiques codés sur un seul octet — Partie1 : Alphabet latin no. 1,1987-02-12,1,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,[28245],"['en','fr']",7,

16339,IS,,ISO 8859-2:1987,Information processing — 8-bit single byte coded graphic character sets — Part 2: Latin alphabet No. 2,Traitement de l'information — Jeux de caractères graphiques codés sur un seul octet — Partie 2: Alphabet latin no. 2,1987-02-12,1,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,[28246],"['en','fr']",6,

16340,IS,,ISO 8859-3:1988,Information processing — 8-bit single-byte coded graphic character sets — Part 3: Latin alphabet No. 3,Traitement de l'information — Jeux de caractères graphiques codés sur un seul octet — Partie 3: Alphabet latin No 3,1988-03-24,1,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,[28247],"['en','fr']",5,

16341,IS,,ISO 8859-4:1988,Information processing — 8-bit single-byte coded graphic character sets — Part 4: Latin alphabet No. 4,Traitement de l'information — Jeux de caractères graphiques codés sur un seul octet — Partie 4: Alphabet latin No 4,1988-03-24,1,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,[28248],"['en','fr']",5,

16343,IS,,ISO 8859-6:1987,Information processing — 8-Bit single-byte coded graphic character sets — Part 6: Latin/Arabic alphabet,Traitement de l'information — Jeux de caractères graphiques codés sur un seul octet — Partie 6: Alphabet latin/arabe,1987-07-30,1,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,[28250],"['en','fr']",5,

16344,IS,,ISO 8859-7:1987,Information processing — 8-bit single-byte coded graphic character sets — Part 7: Latin/Greek alphabet,Traitement de l'information — Jeux de caractères graphiques codés sur un octet — Partie 7: Alphabet latin/grec,1987-11-12,1,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,"[38580,28251]",['en'],5,"<p>This part of ISO 8859 defines a set of 185 graphic characters identified as the Latin/Greek alphabet, and specifies the coded representation of each of these characters by means of a single 8-bit byte. None of these characters are 'non-spacing'.</p><p>The use of control functions, such as BACKSPACE or CARRIAGE RETURN for the coded representation of com­posite characters is pr

16345,IS,,ISO 8859-8:1988,Information processing — 8-bit single-byte coded graphic character sets — Part 8: Latin/Hebrew alphabet,Traitement de l'information — Jeux de caractères graphiques codés sur un seul octet — Partie 8: Alphabet Latin/Hébreu,1988-06-02,1,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,[28252],['en'],5,

16352,IS,,ISO 8861:1988,Shipbuilding — Engine-room ventilation in diesel-engined ships — Design requirements and basis of calculations,Construction navale — Ventilation du compartiment machines des navires à moteurs diesel — Exigences de conception et bases de calcul,1988-10-20,1,['47.020.90'],ISO/TC 8/SC 3,9599,,[25519],"['en','fr']",9,

16353,IS,,ISO 8862:1987,Air-conditioning and ventilation of machinery control-rooms on board ships — Design conditions and basis of calculations,Conditionnement d'air et ventilation des salles de contrôle des machines à bord des navires — Conditions de conception et bases de calcul,1987-03-05,1,['47.020.90'],ISO/TC 8/SC 3,9599,,[76611],"['en','fr']",2,<p>Applies to seagoing merchant ships for all conditions except those encountered in extremely cold or hot climates. Applicable parts of this Standard can be used for similar spaces. The annex provides guidance and details of good practice in the design of ventilation and air-conditioning systems for machinery control rooms.</p>

16354,IS,,ISO 8863:1987,Ship's wheelhouse windows — Heating by hot air of glass panes,Fenêtres de la timonerie des navires — Chauffage à l'air chaud des vitrages,1987-03-19,1,['47.020.90'],ISO/TC 8/SC 3,9599,,[76611],"['en','fr']",1,<p>Is based on an outdoor air temperature of -20 °C and applies to all conditions except those encountered in extremely cold climates. Applies to seagoing merchant ships. The annex gives recommendations regarding the air jets.</p>

16355,IS,,ISO 8864:1987,Air-conditioning and ventilation of wheelhouse on board ships — Design conditions and basis of calculations,Conditionnement d'air et ventilation de la timonerie à bord des navires — Conditions de conception et bases de calcul,1987-03-12,1,['47.020.90'],ISO/TC 8/SC 3,9599,,[76611],"['en','fr']",2,<p>Applies to all conditions except those encountered in extremely cold or hot climate.</p>

5276,IS,,ISO 887:1983,"Plain washers for metric bolts, screws and nuts — General plan",Rondelles plates pour boulonnerie métrique — Plan général,1983-09-01,1,['21.060.30'],ISO/TC 2,9599,,[5277],"['en','fr']",3,

16366,IS,,ISO 8871:1988,Elastomeric parts for aqueous parenteral preparations,Éléments en élastomère pour préparations aqueuses parentérales,1988-11-10,1,['11.040.20'],ISO/TC 76,9599,,[16367],"['en','fr']",,

16367,IS,,ISO 8871:1990,Elastomeric parts for aqueous parenteral preparations,Éléments en élastomère pour préparations aqueuses parentérales,1990-08-23,2,['11.040.20'],ISO/TC 76,9599,[16366],"[33771,28945,33787,33770,38107]","['en','fr']",15,"<p>The elastomeric parts generally called 'rubber' may vary considerably in their composition with regard to fillers, softeners, pigments and other auxiliary ingredients. This standard defines procedures for identifying and classifying elastomeric parts for primary packs and medical devices used in direct contact with the preparations. To avoid any affection of the preparations the 12 normative annexes specify test methods for individual applications.</

23039,IS,Amd,ISO 8871:1990/Amd 1:1995,Elastomeric parts for aqueous parenteral preparations — Amendment 1,Éléments en élastomère pour préparations aqueuses parentérales — Amendement 1,1995-10-05,2,['11.040.20'],ISO/TC 76,9599,,"[33771,28945,33787,33770,38107]","['en','fr']",5,<p>Contains minor amendments and adds two new annexes.</p>

28945,IS,,ISO 8871-2:2003,Elastomeric parts for parenterals and for devices for pharmaceutical use — Part 2: Identification and characterization,Éléments en élastomère pour administration parentérale et dispositifs à usage pharmaceutique — Partie 2: Identification et caractérisation,2003-09-19,1,['11.040.20'],ISO/TC 76,9599,"[23039,34989,16367]",[76110],"['en','fr','ru']",20,"<p>ISO 8871-2:2003 specifies evaluation procedures applicable to elastomeric parts used for drug containers and medical devices in order to guarantee the product identity between the samples evaluated in the (suitability test) acceptance process and the current supplies. The physical and chemical test procedures specifi

39803,IS,Amd,ISO 8871-2:2003/Amd 1:2005,Elastomeric parts for parenterals and for devices for pharmaceutical use — Part 2: Identification and characterization — Amendment 1,Éléments en élastomère pour administration parentérale et dispositifs à usage pharmaceutique — Partie 2: Identification et caractérisation — Amendement 1,2005-07-22,1,['11.040.20'],ISO/TC 76,9599,,[76110],"['en','fr','ru']",3,

38107,IS,,ISO 8871-5:2005,Elastomeric parts for parenterals and for devices for pharmaceutical use — Part 5: Functional requirements and testing,Éléments en élastomère pour administration parentérale et dispositifs à usage pharmaceutique — Partie 5: Exigences fonctionnelles et essais,2005-08-15,1,['11.040.20'],ISO/TC 76,9599,"[23039,16367]",[68560],"['en','fr','ru']",10,<p>ISO 8871-5:2005 specifies requirements and test methods for functional parameters of elastomeric closures used in combination with vials and when pierced by an injection needle. </p>

68560,IS,,ISO 8871-5:2016,Elastomeric parts for parenterals and for devices for pharmaceutical use — Part 5: Functional requirements and testing,Éléments en élastomère pour administration parentérale et dispositifs à usage pharmaceutique — Partie 5: Exigences fonctionnelles et essais,2016-10-13,2,['11.040.20'],ISO/TC 76,9599,[38107],[85863],"['en','fr']",10,<p>ISO 8871-5:2016 specifies requirements and test methods for functional parameters of elastomeric closures used in combination with vials and when pierced by an injection needle.</p><p>NOTE Functional testing with spikes is specified in ISO 8536‑2 and in ISO 8536‑6.</p>

16368,IS,,ISO 8872:1988,"Aluminium caps for transfusion, infusion and injection bottles — General requirements and test methods","Capsules en aluminium pour flacons de transfusion, perfusion et injection — Spécifications générales et méthodes d'essai",1988-12-08,1,['11.040.20'],ISO/TC 76,9599,,[35060],"['en','fr']",5,"<p>In opposition to vials and the elastomeric parts the caps are not considered as primary packaging materials that will come into direct contact with pharmaceutical preparations or blood. Thus, the tests are mainly related to their mechanical protection characteristics.</p>"

35060,IS,,ISO 8872:2003,"Aluminium caps for transfusion, infusion and injection bottles — General requirements and test methods","Capsules en aluminium pour flacons de transfusion, perfusion et injection — Spécifications générales et méthodes d'essai",2003-03-14,2,['11.040.20'],ISO/TC 76,9599,[16368],"[79680,82226]","['en','fr']",6,"<p>ISO 8872:2003 specifies general requirements and test methods for aluminium caps for injection vials, and for infusion and transfusion bottles.</p>"

16369,IS,,ISO 8873:1987,"Cellular plastics, rigid — Spray-applied polyurethane foam for thermal insulation of buildings — Specification",Plastiques alvéolaires rigides — Mousse de polyuréthanne projetée utilisée dans l'isolation thermique des bâtiments — Spécifications,1987-11-19,1,['83.100'],ISO/TC 61/SC 10,9599,,"[28879,39406,39378,39407]","['en','fr']",5,<p>Specifies the rquirements and test methods for spray- applied rigid polyurethane cellular plastics used as thermal insulation in two loadbearing categories. The foam may be either produce on site or in a manufactoring facility. The test samples shall be representative of the in place finshed material and of sufficient quantity and size

39407,IS,,ISO 8873-3:2007,Rigid cellular plastics — Spray-applied polyurethane foam for thermal insulation — Part 3: Test methods,Plastiques alvéolaires rigides — Mousse de polyuréthanne projetée pour l'isolation thermique — Partie 3: Méthodes d'essai,2007-05-04,1,['83.100'],ISO/TC 61/SC 10,9599,[16369],[45304],['en'],17,<p>ISO 8873-3:2007 specifies the test procedures that are to be used when testing spray-applied polyurethane foam materials to verify that they meet the requirements given in ISO 8873-1:2006.</p>

16371,IS,,ISO 8875:1988,Fluorspar — Determination of moisture content of a lot,Spaths fluor — Détermination de l'humidité d'un lot,1988-12-01,1,['73.080'],ISO/TC 175,9599,,[16372],"['en','fr']",3,

16375,IS,,ISO 8877:1987,Information processing systems — Interface connector and contact assignments for ISDN basic access interface located at reference points S and T,Systèmes de traitement de l'information — Connecteur d'interface et affectation des contacts pour l'interface d'accès de base au RNIS située aux points de référence S et T,1987-07-30,1,['35.100.10'],ISO/IEC JTC 1/SC 6,9599,,[21311],"['en','fr']",9,

16376,IS,Amd,ISO 8877:1987/Amd 1:1991,Information processing systems — Interface connector and contact assignments for ISDN basic access interface located at reference points S and T — Amendment 1,Systèmes de traitement de l'information — Connecteur d'interface et affectation des contacts pour l'interface d'accès de base au RNIS située aux points de référence S et T — Amendement 1,1991-05-23,1,['35.100.10'],ISO/IEC JTC 1/SC 6,9599,,[21311],['en'],2,

16377,IS,,ISO 8878:1987,Information processing systems — Data communications — Use of X.25 to provide the OSI connection-mode network service,Systèmes de traitement de l'information — Communication de données — Utilisation du protocole X.25 pour fournir le service de réseau OSI en mode connexion,1987-09-01,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[16385],['en'],63,

16379,IS,Add,ISO 8878:1987/Add 2:1990,Information processing systems — Data communications — Use of X.25 to provide the OSI connection-mode network service — Addendum 2,Systèmes de traitement de l'information — Communication de données — Utilisation du protocole X.25 pour fournir le service de réseau OSI en mode connexion — Additif 2,1990-06-20,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[16386],['en'],5,

16380,IS,Amd,ISO 8878:1987/Amd 3:1991,Information processing systems — Data communications — Use of X.25 to provide the OSI connection-mode network service — Amendment 3,Systèmes de traitement de l'information — Communication de données — Utilisation du protocole X.25 pour fournir le service de réseau OSI en mode connexion — Amendement 3,1991-06-20,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[16385],['en'],6,

16381,IS,Cor,ISO 8878:1987/Cor 1:1990,Information processing systems — Data communications — Use of X.25 to provide the OSI connection-mode network service — Technical Corrigendum 1,Systèmes de traitement de l'information — Communication de données — Utilisation du protocole X.25 pour fournir le service de réseau OSI en mode connexion — Rectificatif technique 1,1990-02-22,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[16385],['en'],1,

16386,IS,Cor,ISO 8878:1987/Cor 1:1991,Information processing systems — Data communications — Use of X.25 to provide the OSI connection-mode network service — Technical Corrigendum 1,Systèmes de traitement de l'information — Communication de données — Utilisation du protocole X.25 pour fournir le service de réseau OSI en mode connexion — Rectificatif technique 1,1991-05-16,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,[16379],[16385],,,

16382,IS,Cor,ISO 8878:1987/Cor 2:1990,Information processing systems — Data communications — Use of X.25 to provide the OSI connection-mode network service — Technical Corrigendum 2,Systèmes de traitement de l'information — Communication de données — Utilisation du protocole X.25 pour fournir le service de réseau OSI en mode connexion — Rectificatif technique 2,1990-06-21,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[16385],['en'],2,

16383,IS,Cor,ISO 8878:1987/Cor 3:1990,Information processing systems — Data communications — Use of X.25 to provide the OSI connection-mode network service — Technical Corrigendum 3,Systèmes de traitement de l'information — Communication de données — Utilisation du protocole X.25 pour fournir le service de réseau OSI en mode connexion — Rectificatif technique 3,1990-09-03,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[16385],['en'],3,

16384,IS,Cor,ISO 8878:1987/Cor 4:1991,Information processing systems — Data communications — Use of X.25 to provide the OSI connection-mode network service — Technical Corrigendum 4,Systèmes de traitement de l'information — Communication de données — Utilisation du protocole X.25 pour fournir le service de réseau OSI en mode connexion — Rectificatif technique 4,1991-04-25,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[16385],['en'],2,

5278,IS,,ISO 888:1976,"Bolts, screws and studs — Nominal lengths, and thread lengths for general purpose bolts","Boulons, vis et goujons — Longueurs de tige nominales, et longueurs filetées des boulons d'application générale",1976-05-01,1,['21.060.10'],ISO/TC 2/SC 7,9599,,[50946],"['en','fr']",2,<p>Specifies the nominal lengths from 2 mm up to and including 300 mm as well as from 1/16 inch up to and including 12 inch resp.; gives the coordination for thread lengths/diameters for the dimensions in millimeters and inches.</p>

16403,IS,,ISO 8884:1989,Information processing — Text and office systems — Keyboards for multiple Latin-alphabet languages — Layout and operation,Traitement de l'information — Systèmes bureautiques — Claviers pour des langues à l'alphabet latin multiples — Disposition et opération,1989-08-31,1,['35.180'],ISO/IEC JTC 1,9599,,"[17914,17910,17911,17915,17912,17909,17913]",['en'],10,

16404,IS,,ISO 8885:1987,Information processing systems — Data communication — High-level data link control procedures — General purpose XID frame information field content and format,Systèmes de traitement de l'information — Communications de données — Format et contenu du champ d'information de XID pour application générale,1987-07-30,1,['35.100.20'],ISO/IEC JTC 1/SC 6,9599,,[16405],['en'],,

16417,IS,,ISO 8891:1990,Dental casting alloys with noble metal content of 25 % up to but not including 75 %,Alliages dentaires à couler avec une teneur en métaux précieux comprise entre 25 % et 75 %,1990-02-01,1,['11.060.10'],ISO/TC 106/SC 2,9599,,[20962],"['en','fr']",5,

20962,IS,,ISO 8891:1993,Dental casting alloys with noble metal content of 25 % up to but not including 75 %,Alliages dentaires à couler avec une teneur en métaux précieux comprise entre 25 % et 75 %,1993-12-02,2,['11.060.10'],ISO/TC 106/SC 2,9599,[16417],[24817],"['en','fr']",5,

24817,IS,,ISO 8891:1998,Dental casting alloys with noble metal content of at least 25 % but less than 75 %,Alliages dentaires à couler avec une teneur en métaux précieux supérieure ou égale à 25 % et strictement inférieure à 75 %,1998-12-20,3,['11.060.10'],ISO/TC 106/SC 2,9599,[20962],[36412],"['en','fr']",10,

16419,IS,,ISO 8893:1989,Forestry machinery — Portable brush-saws — Engine performance and fuel consumption,Machines forestières — Débroussailleuses portatives — Puissance et consommation du moteur,1989-10-19,1,['65.060.80'],ISO/TC 23/SC 17,9599,,[25974],"['en','fr']",3,

25974,IS,,ISO 8893:1997,Forestry machinery — Portable brush-cutters and grass-trimmers — Engine performance and fuel consumption,Machines forestières — Débroussailleuses et coupe-herbe portatifs — Puissance et consommation de carburant du moteur,1997-12-18,2,['65.060.80'],ISO/TC 23/SC 17,9599,[16419],[79636],"['en','fr']",5,

79636,IS,,ISO 8893:2021,Forestry machinery — Portable brush-cutters and grass-trimmers — Engine performance and fuel consumption,Machines forestières — Débroussailleuses et coupe-herbe portatifs — Puissance et consommation de carburant du moteur,2021-10-22,3,['65.060.80'],ISO/TC 23/SC 17,9599,[25974],[86335],"['en','fr']",5,<p>This document specifies a method for testing the performance and fuel consumption of internal combustion engines used to power portable brush-cutters and grass trimmers.</p>

16420,IS,,ISO 8894-1:1987,Refractory materials — Determination of thermal conductivity — Part 1: Hot-wire method (cross-array),Matériaux réfractaires — Détermination de la conductivité thermique — Partie 1: Méthode du fil chaud (croisillon),1987-03-26,1,['81.080'],ISO/TC 33,9599,,[50737],"['en','fr']",6,"<p>Belongs to a series of standard and specifies a hot-wire method for the determination of the thermal conductivety of refractory products. The method is applicable at temperatures not higher than 1250 °C and to materials whose thermal conductivity is less than 1,5 W/(m.k) and whose thermal diffusivity is less than 10-6 m2/s. Subject to the limits in 1.2, the method is applicable to powdere

16421,IS,,ISO 8894-2:1990,Refractory materials — Determination of thermal conductivity — Part 2: Hot-wire method (parallel),Matériaux réfractaires — Détermination de la conductivité thermique — Partie 2: Méthode du fil chaud (parallèle),1990-11-15,1,['81.080'],ISO/TC 33,9599,,"[26566,44465]","['en','fr']",9,<p>Specifies a hot-wire method for the determination of the thermal conductivity of refractory products and materials. Is applicable at temperatures up to and including 1250°C and to materials with a thermal conductivity less than 25 W/(m.K); does not apply to electrically conducting materials.</p>

16422,IS,,ISO 8895:1986,Shaped insulating refractory products — Determination of cold crushing strength,Produits réfractaires isolants façonnés — Détermination de la résistance à l'écrasement à température ambiante,1986-10-09,1,['81.080'],ISO/TC 33,9599,,"[20291,36214]","['en','fr']",2,

16423,IS,,ISO 8896:1987,Oil of caraway (Carum carvi Linnaeus),Huile essentielle de carvi (Carum carvi Linnaeus),1987-06-18,1,['71.100.60'],ISO/TC 54,9599,,"[66253,53438]","['en','fr']",3,"<p>The Standard specifies the following characteristics of the oil. Appearance: Mobile liquid. Colour: Almost colourless to amber-yellow. Odour: Characteristic, aromatic. Taste: Reminiscent of anise, aromatic. Relative density at 20/20 °C: 0,901 - 0,920. Refractive index at 20 °C: 1,4840 - 1,4890. Optical rotation at 20 °C: Between + 67 and + 80 . Miscibility with 80 % (V/V) ethanol at 20 °C: 1 : 8. Acid value: Maximum 1,0. Carbonyl value: 179 - 243. Chromatographic profile: A typical chromatogram is given.

16424,IS,,ISO 8897:1991,Oil of juniper berry (Juniperus communis Linnaeus),Huile essentielle de baies de genévrier (Juniperus communis Linnaeus),1991-10-17,1,['71.100.60'],ISO/TC 54,9599,,[46552],"['en','fr']",5,"<p>Specifies certain characteristics in order to facilitate the assessment of quality. Describes requirements, sampling, methods of test, packaging, labelling, and marking. Annex A is for information only.</p>"

16426,IS,,ISO 8899:1991,Oil of lemon petitgrain [Citrus limon (Linnaeus) N.L.Burman],Huile essentielle de petitgrain citronnier [Citrus limon (Linnaeus) N.L.Burman],1991-06-20,1,['71.100.60'],ISO/TC 54,9599,,[34432],"['en','fr']",5,

3739,IS,,ISO 89:1974,Steel — Tensile testing of wire,Acier — Essai de traction des fils,1974-08-01,1,"['77.140.65','77.040.10']",ISO/TC 164/SC 1,9599,,[13414],"['en','fr']",6,

16427,IS,,ISO 8900:1987,Oil of bergamot petitgrain (Citrus aurantium (Linnaeus) ssp. bergamia (Wight et Arnott) Engler),Huile essentielle de petitgrain bergamotier (Citrus aurantium (Linnaeus) ssp. bergamia (Wight et Arnott) Engler),1987-10-15,1,['71.100.60'],ISO/TC 54,9599,,[37052],"['en','fr']",3,"<p>The Standard specifies the following characteristics of the oil. Appearance: Clear liquid. Colour: Amber. Odour: Characteristic. Relative density at 20/20 °C: 0,886 - 0,894. Refractive index at 20 °C: 1,4600 - 1,4650. Optical rotation at 20 °C: Between - 4 and + 3 . Miscibility with 70 % (V/V) ethanol at 20 °C: 1 : 3. Acid value: Maximum 2,0. Ester value: 115 - 195. Ester value after acetylati

16428,IS,,ISO 8901:1987,Oil of bitter orange petitgrain (Citrus aurantium Linnaeus ssp. aurantium),Huile essentielle de petitgrain bigaradier (Citrus aurantium Linnaeus ssp. aurantium),1987-06-11,1,['71.100.60'],ISO/TC 54,9599,,[28586],"['en','fr']",4,"<p>The Standard specifies the following characteristics of the oil. Appearance: Clear liquid. Colour: Pale yellow to amber-yellow.with a slight blue fluorescence. Odour: Characteristic, ethereal and pleasant. Relative density at 20/20 °C: 0,888 - 0,898. Refractive index at 20 °C: 1,4560 - 1,4720. Optical rotation at 20 °C: - 6 and + 1 . Miscibility with 70 % (V/V) ethanol at 20 °C: 1 : 1,5. Acid value: Maximum 2,0. Ester value: 140 - 217. Chro

16429,IS,,ISO 8902:1987,Oil of lavandin grosso (Lavandula angustifolia P. Miller x Lavandula latifolia (Linnaeus f.) Medikus),Huile essentielle de lavandin grosso (Lavandula angustifolia P. Miller x Lavandula latifolia (Linnaeus f.) Medikus),1987-11-12,1,['71.100.60'],ISO/TC 54,9599,,[24651],"['en','fr']",4,

24651,IS,,ISO 8902:1999,"Oil of lavandin Grosso (Lavandula angustifolia Miller x Lavandula latifolia (L.f.) Medikus), French type","Huile essentielle de lavandin Grosso (Lavandula angustifolia Miller x Lavandula latifolia (L.f.) Medikus), type France",1999-11-11,2,['71.100.60'],ISO/TC 54,9599,[16429],[45332],"['en','fr']",5,

45332,IS,,ISO 8902:2009,"Oil of lavandin Grosso (Lavandula angustifolia Mill. x Lavandula latifolia Medik.), French type","Huile essentielle de lavandin Grosso (Lavandula angustifolia Mill. x Lavandula latifolia Medik.), type France",2009-03-16,3,['71.100.60'],ISO/TC 54,9599,[24651],[88590],"['en','fr']",8,"<p>ISO 8902:2009 specifies certain characteristics of the essential oil of lavandin Grosso [<i>Lavandula angustifolia </i>Mill. x <i>Lavandula latifolia </i>Medik.] French type, intended for facilitating the assessment of its quality.</p>"

16430,IS,,ISO 8903:1994,Broadleaved sawn timber — Nominal sizes,Sciages de bois feuillus — Dimensions nominales,1994-10-20,1,['79.040'],ISO/TC 218,9599,,[62871],"['en','fr']",1,"<p>Specifies nominal sizes of unplaned, square-edged and unedged, broadleaved sawn timber.</p>"

16432,IS,,ISO 8905:1988,Sawn timber — Test methods — Determination of ultimate strength in shearing parallel to grain,Bois sciés — Méthodes d'essai — Détermination de la contrainte de rupture en cisaillement parallèle aux fibres,1988-06-23,1,['79.040'],ISO/TC 218,9599,,[52511],"['en','fr']",2,<p>This International Standard specifies a method of testing sawn timber of coniferous and broadleaved species in shearing parallel to the grain to determine the ultimate strength. </p>

16436,IS,,ISO 8909-1:1994,Forage harvesters — Part 1: Vocabulary,Récolteuses-hacheuses-chargeuses de fourrage — Partie 1: Vocabulaire,1994-03-03,1,"['01.040.65','65.060.50']",ISO/TC 23/SC 7,9599,,[77755],"['en','fr']",17,"<p>Specifies, in English and French, 70 terms and definitions relating to forage harvesters and their component parts: general terms, characteristics of functional components, machine and functional component characteristics, crop terminology, performance terms. In association with ISO 8909-2, which lays down methods of measuring characteristics and performance requirements for the term defined, this part identifies dimensions and other characteristics aimed at allowing com

22380,IS,,ISO 8909-2:1994,Forage harvesters — Part 2: Specification of characteristics and performance,Récolteuses-hacheuses-chargeuses de fourrage — Partie 2: Spécification des caractéristiques et des performances,1994-03-03,1,['65.060.50'],ISO/TC 23/SC 7,9599,,[77756],"['en','fr']",4,"<p>Specifies the methods and requirements in assessing the dimensions and performance of a forage harvester, as defined in ISO 8909-1, and its functional components. Also allows comparison of forage harvester performance through comparative testing.</p>"

16437,IS,,ISO 8909-3:1994,Forage harvesters — Part 3: Test methods,Récolteuses-hacheuses-chargeuses de fourrage — Partie 3: Méthodes d'essai,1994-03-03,1,['65.060.50'],ISO/TC 23/SC 7,9599,,[77757],"['en','fr']",11,"<p>Specifies test methods for evaluations of forage harvester function and performance, covering forage harvesters which cut the crop directly at full width or from spaced-apart plant rows, or which pickup precut crop. Applies to forage harvesters with driven knives for chopping and which deliver the chopped crop into a container or a separate vehicle or trailer. The harvesters may be tractor-mounted, trailed or self-propelled.</p>"

16438,IS,,ISO 8910:1987,Machinery and equipment for working the soil — Mouldboard ploughs — Working elements — Vocabulary,Matériel de travail du sol — Charrues à socs — Pièces travaillantes — Vocabulaire,1987-09-24,1,"['01.040.65','65.060.20']",ISO/TC 23,9599,,[16439],"['en','fr','ru']",8,

16441,IS,,ISO 8913:1989,"Aerospace — Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 204 degrees C/21 000 kPa — Procurement specification","Aéronautique et espace — Tuyauteries flexibles en polytétrafluoréthylène (PTFE), série légère, classification 204 degrés C/21 000 kPa — Spécification d'approvisionnement",1989-12-07,1,"['83.140','49.080']",ISO/TC 20/SC 10,9599,,[16442],"['en','fr']",12,

16443,IS,Cor,ISO 8913:1989/Cor 1:1990,"Aerospace — Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 204 degrees C/21 000 kPa — Procurement specification — Technical Corrigendum 1","Aéronautique et espace — Tuyauteries flexibles en polytétrafluoréthylène (PTFE), série légère, classification 204 degrés C/21 000 kPa — Spécification d'approvisionnement — Rectificatif technique 1",1990-09-06,1,['49.080'],ISO/TC 20/SC 10,9599,,[16442],['en'],2,

16442,IS,,ISO 8913:1994,"Aerospace — Lightweight polytetrafluoroethylene (PTFE) hose assemblies, classification 204 degrees C/21 000 kPa — Procurement specification","Aéronautique et espace — Tuyauteries flexibles en polytétrafluoroéthylène (PTFE), série légère, classification 204 degrés C/21 000 kPa — Spécification d'approvisionnement",1994-12-08,2,"['83.140.40','49.080']",ISO/TC 20/SC 10,9599,"[16443,16441]","[40696,31751]","['en','fr']",15,<p>Cancels and replaces the first edition (1989). Specifies requirements for lightweight polytetrafluoroethylene hose assemblies for use in aircraft hydraulic systems at temperatures between -55 °C and +204 °C and at a nominal pressure up to 21 000 kPa.

5283,IS,,ISO 893:1978,Surface active agents — Technical sodium alkane sulphonates — Methods of analysis,Agents de surface — Alkylsulfonates de sodium techniques — Méthode d'analyse,1978-11-01,1,['71.100.40'],ISO/TC 91,9599,,[5284],"['en','fr']",6,

16459,IS,,ISO 8930:1987,General principles on reliability for structures — List of equivalent terms,Principes généraux de la fiabilité des constructions — Liste de termes équivalents,1987-12-17,1,"['91.080.01','01.040.91']",ISO/TC 98/SC 1,9599,,"[44605,74452,26779,36006]","['en','fr','ru']",20,"<p>Fixes the equivalence of the principal terms used in the field of reliability of structures, in different languages (English, French, Russian and German). An annex contains approximate but simple definitions of, and commentary on, the terms listed, gives indications about their use and quotes the corresponding symbols and subscripts.</p>"

16461,IS,,ISO 8936:1988,Caravan awnings — Safety requirements,Auvents de caravane — Exigences de sécurité,1988-08-18,1,"['97.200.30','43.100']",ISO/TC 83,9599,,[34790],"['en','fr']",2,"<p>Specifies the technical requirements of safety for awning frame and pegs, zip fasteners, safety ventilation, fire precautions, means of escape and safety instructions for caravans. For functional requirements see ISO 8937. The notice giving simple fire prevention advice inside the awning is given in English and French.</p>"

34790,IS,,ISO 8936:2003,Caravan awnings — Safety requirements,Auvents de caravane — Exigences de sécurité,2003-01-30,2,"['97.200.30','43.100']",ISO/TC 83,9599,[16461],[39981],"['en','fr']",3,"<p>ISO 8936:2003 specifies the technical requirements of safety for awnings for rigid caravans, folding caravans, trailer tents and motor caravans as defined in ISO 7418.</p>"

39981,IS,,ISO 8936:2007,Awnings for leisure accommodation vehicles — Requirements and test methods,Auvents pour véhicules de loisirs habitables — Exigences et méthodes d'essai,2007-09-10,3,"['97.200.30','43.100']",ISO/TC 83,9599,"[34790,29737]",[63114],"['en','fr']",13,"<p>ISO 8936:2007 specifies requirements and test methods for awnings for leisure accommodation vehicles. It applies to awnings of residential, touring or winter types.</p>"

16462,IS,,ISO 8937:1991,Caravan awnings — Functional requirements and test methods,Auvents de caravane — Exigences de fonctionnement et méthodes d'essai,1991-10-31,1,"['97.200.30','43.100']",ISO/TC 83,9599,,[29737],"['en','fr']",8,

29737,IS,,ISO 8937:2000,Caravan awnings — Functional requirements and test methods,Auvents de caravane — Exigences de fonctionnement et méthodes d'essai,2000-02-10,2,"['97.200.30','43.100']",ISO/TC 83,9599,[16462],[39981],"['en','fr']",11,

16464,IS,,ISO 8940:1988,"Aerospace — Nuts, anchor, self-locking, sealing, floating, two-lug, with counterbore, classifications 900 MPa/120 degrees C, 900 MPa/175 degrees C and 900 MPa/235 degrees C — Dimensions","Aéronautique et espace — Écrous à river à freinage interne, étanches, flottants, double patte, avec chambrage, classifications 900 MPa/120 degrés C, 900 MPa/175 degrés C et 900 MPa/235 degrés C — Dimensions",1988-05-19,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[31734],"['en','fr']",2,"<p>Establishes these values for nuts, with a self-locking feature achieved by forming the upper portion of the nut element out-of-round, having these classifications and into which a sealing ring is incorpo

16467,IS,,ISO 8943:1991,Refrigerated light hydrocarbon fluids — Sampling of liquefied natural gas — Continuous method,Hydrocarbures liquides légers réfrigérés — Échantillonnage de gaz naturel liquéfié — Méthode continue,1991-11-21,1,['75.060'],ISO/TC 28/SC 5,9599,,[41508],"['en','fr']",11,"<p>Describes the sampling system, the apparatus, the sampling procedure, and the contents of the sampling report. Gives precautions. Specifies 15 terms and definitions. Annex A is for information only.</p>"

41508,IS,,ISO 8943:2007,Refrigerated light hydrocarbon fluids — Sampling of liquefied natural gas — Continuous and intermittent methods,Hydrocarbures liquides légers réfrigérés — Échantillonnage de gaz naturel liquéfié — Méthodes en continu et par intermittence,2007-03-01,2,['75.060'],ISO/TC 28/SC 5,9599,[16467],[84462],"['en','fr','ru']",20,<p>ISO 8943:2007 specifies methods for the continuous and the intermittent sampling of LNG while it is being transferred through an LNG transfer line.</p>

16484,IS,,ISO 8960:1991,"Refrigerators, frozen-food storage cabinets and food freezers for household and similar use — Measurement of emission of airborne acoustical noise","Réfrigérateurs, conservateurs et congélateurs à usage ménager et analogue — Mesure de l'émission du bruit aérien",1991-07-18,1,['97.040.30'],ISO/TC 86,9599,,[45556],"['en','fr']",5,<p>The heading 'Replacement' indicates that the text given in this standard replaces the relevant text in IEC 704-1; similarly the heading 'Addition' indicates that the text given in this standard supplements the relevant text in IEC 704-1. Annexes A and B are for information only.</p>

16485,IS,,ISO 8962:1987,Plastics — Polymer dispersions — Determination of density,Plastiques — Dispersions de polymères — Détermination de la masse volumique,1987-10-08,1,['83.080.01'],ISO/TC 61/SC 9,9599,,"[2455,25478]","['en','fr']",5,

16488,IS,,ISO 8965:1987,Logging industry — Technology — Terms and definitions,Exploitation forestière — Techniques — Termes et définitions,1987-11-05,1,"['79.020','01.040.79']",ISO/TC 218,9599,,"[37126,52488]","['en','fr','ru']",8,"<p>Relates to production operations. The standard is a trilingual edition and includes an alphabetical index in English, French and Russian.</p>"

52488,IS,,ISO 8965:2013,Logging industry — Technology — Terms and definitions,Exploitation forestière — Techniques — Termes et définitions,2013-10-15,2,"['79.020','01.040.79']",ISO/TC 218,9599,[16488],[74837],"['en','ru']",26,<p>ISO 8365:2013 defines terms relating to technological operations in the logging industry.</p>

16489,IS,,ISO 8966:1987,Logging industry — Products — Terms and definitions,Exploitation forestière — Produits — Termes et définitions,1987-10-29,1,"['79.020','01.040.79']",ISO/TC 218,9599,,"[37126,52502]","['en','fr','ru']",7,"<p>Covers products used in various fields, e.g. logs for the pulp and paper industry, board production and chemical processing as well as fuel-woods. Is a trilingual edition and includes an alphabetical index in English, French, and Russian.</p>"

16490,IS,,ISO 8967:1992,Dried milk and dried milk products — Determination of bulk density,Lait sec et produits laitiers en poudre — Détermination de la masse volumique,1992-01-23,1,['67.100.10'],ISO/TC 34/SC 5,9599,,[42701],"['en','fr']",4,"<p>Specifies the principle, the apparatus, the sampling and preparation of the test sample, the test procedure, the expression of results, the precision and the test report.</p>"

35120,IS,,ISO 8968-1:2001,Milk — Determination of nitrogen content — Part 1: Kjeldahl method,Lait — Détermination de la teneur en azote — Partie 1: Méthode Kjeldahl,2001-12-20,1,['67.100.10'],ISO/TC 34/SC 5,9599,,[61020],"['en','fr']",11,"<p>ISO 8968-1|IDF 20-1:2001 specifies a method for the determination of the nitrogen content of liquid milk, whole or skimmed, by the Kjeldahl principle.</p>"

35121,IS,,ISO 8968-2:2001,Milk — Determination of nitrogen content — Part 2: Block-digestion method (Macro method),Lait — Détermination de la teneur en azote — Partie 2: Méthode de minéralisation en bloc (Méthode macro),2001-12-20,1,['67.100.10'],ISO/TC 34/SC 5,9599,,[61020],"['en','fr']",9,"<p>ISO 8968-2|IDF 20-2:2001 specifies a method for the determination of the nitrogen content of liquid milk, whole or skimmed, by the block-digestion principle.</p>"

35122,IS,,ISO 8968-4:2001,Milk — Determination of nitrogen content — Part 4: Determination of non-protein-nitrogen content,Lait — Détermination de la teneur en azote — Partie 4: Détermination de la teneur en azote non protéique,2001-12-20,1,['67.100.10'],ISO/TC 34/SC 5,9599,,[60386],"['en','fr']",6,"<p>ISO 8968-4|IDF 20-4:2001 specifies a method for the determination of the non-protein nitrogen content of liquid milk, whole or skimmed.</p>"

60537,IS,Cor,ISO 8968-4:2001/Cor 1:2011,Milk — Determination of nitrogen content — Part 4: Determination of non-protein-nitrogen content — Technical Corrigendum 1,Lait — Détermination de la teneur en azote — Partie 4: Détermination de la teneur en azote non protéique — Rectificatif technique 1,2011-11-03,1,['67.100.10'],ISO/TC 34/SC 5,9599,,"[61020,60386]",['fr'],,