Withdrawn and superseded ISO standards — page 172 of 246

15631,IS,,ISO 8444:1985,"Pipework — Double overlap flexible metal hoses (copper packing, limited tightness, circular section, in protected carbon steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage double (joint cuivre, étanchéité limitée, section circulaire, en acier non allié protégé)",1985-10-03,1,['23.040.70'],ISO/TC 5/SC 11,9599,,[27752],"['en','fr']",2,"<p>Specifies diameters of hoses and given requirements to be verified in accordance with ISO 7658. Applies to uncoated hoses used under low pressure with permissible leakage, at temperatures from -20 to +600 C. A figure illustrates the meaning of the text. Gives an example of designation. The table includes nominal sizes from

15632,IS,,ISO 8445:1985,"Pipework — Double overlap flexible metal hoses (asbestos packing, leakproof, circular section, in protected carbon steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage double (joint amiante, étanches, section circulaire, en acier non allié protégé)",1985-09-26,1,['23.040.70'],ISO/TC 5/SC 11,9599,,[22838],"['en','fr']",2,

22838,IS,,ISO 8445:1995,"Pipework — Double overlap flexible metal hoses (with packing, leakproof, circular section, in protected carbon steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage double (avec joint, étanches, de section circulaire, en acier non allié protégé)",1995-02-23,2,['23.040.70'],ISO/TC 5/SC 11,9599,[15632],[27752],"['en','fr']",3,"<p>Cancels and replaces the first edition (1985). Specifies the diameters of double overlap leakproof flexible metal hoses with packing, of circular section, in protected carbon steel. The packing should not be asbestos. Suitable materials include, for example, cotton, fibre-glass, nylon, Kevlar, polyamide, polyester etc. Applies to flex

15633,IS,,ISO 8446:1985,"Pipework — Double overlap flexible metal hoses (asbestos packing, leakproof, circular section, in austenitic stainless steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage double (joint amiante, étanches, section circulaire, en acier inoxydable austénitique)",1985-10-03,1,['23.040.70'],ISO/TC 5/SC 11,9599,,[22839],"['en','fr']",2,

22839,IS,,ISO 8446:1995,"Pipework — Double overlap flexible metal hoses (with packing, leakproof, circular section, in austenitic stainless steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage double (avec joint, étanches, de section circulaire, en acier inoxydable austénitique)",1995-02-23,2,['23.040.70'],ISO/TC 5/SC 11,9599,[15633],[27752],"['en','fr']",3,"<p>Cancels and replaces the first edition (1985). Specifies the diameters of double overlap leakproof flexible metal hoses with packing, of circular section, in austenitic stainless steel. The packing should not be asbestos. Suitable materials include, for example, cotton, fibre-glass, nylon, Kevlar, polyamide, polyester etc. A

15634,IS,,ISO 8447:1986,"Pipework — Single overlap flexible metal hoses (rubber packing, limited tightness, circular or polygonal section, in protected carbon steel)","Tuyauteries — Tuyaux métalliques fexibles à agrafage simple (joint caoutchouc, étanchéité limitée, section circulaire ou polygonale, en acier non allié protégé)",1986-11-27,1,['23.040.70'],ISO/TC 5/SC 11,9599,,[27752],"['en','fr']",2,"<p>Specifies diameters of hoses and given requirements to be verified in accordance with ISO 7658. Applies to uncoated hoses used under low pressure with permissible leakage, at temperatures from -20 to +60 C. A figure illustrates the meaning of the text. Gives an example of designation. The tabl

15635,IS,,ISO 8448:1986,"Pipework — Double overlap flexible metal hoses (unpacked, limited tightness, circular or polygonal section, in protected carbon steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage double (sans joint, étanchéité limitée, section circulaire ou polygonale, en acier non allié protégé)",1986-11-27,1,['23.040.70'],ISO/TC 5/SC 11,9599,,"[25836,27752]","['en','fr']",2,"<p>Specifies diameters of hoses and gives requirements to be verified in accordance with ISO 7658. Applies to uncoated hoses under low pressure with permissible leakage, at temperatures from -20 to +600 C. A figure illustrates the meaning of the text. Gives an example of designation. The table inclu

15636,IS,,ISO 8449:1986,"Pipework — Single overlap flexible metal hoses (asbestos packing, limited tightness, circular or polygonal section, in protected carbon steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage simple (joint amiante, étanchéité limitée, section circulaire ou polygonale, en acier non allié protégé)",1986-11-27,1,['23.040.70'],ISO/TC 5/SC 11,9599,,[22840],"['en','fr']",2,

22840,IS,,ISO 8449:1995,"Pipework — Single overlap flexible metal hoses (with packing, limited tightness, circular or polygonal section, in protected carbon steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage simple (avec joint, à étanchéité limitée, de section circulaire ou polygonale, en acier non allié protégé)",1995-01-26,2,['23.040.70'],ISO/TC 5/SC 11,9599,[15636],[27752],"['en','fr']",2,"<p>Specifies the diameters of the flexible metal hoses in accordance with ISO 7657 and tested in accordance with ISO 7658 without external coating (as defined in ISO 7369:1983, 4.1.10), used under low pressure, with permissible leakage, at temperatures between - 20 °C and a maximum of 230 °C

5217,IS,,ISO 845:1977,Cellular rubbers and plastics — Determination of apparent density,Caoutchoucs et plastiques alvéolaires — Détermination de la masse volumique apparente,1977-12-01,1,['83.100'],ISO/TC 61,9599,,[5218],"['en','fr']",2,

5218,IS,,ISO 845:1988,Cellular plastics and rubbers — Determination of apparent (bulk) density,Caoutchoucs et plastiques alvéolaires — Détermination de la masse volumique apparente,1988-11-24,2,['83.100'],ISO/TC 61/SC 10,9599,"[6523,5217]","[39408,33340]","['en','fr']",3,"<p>Specification of a method for determining the apparent density or the bulk density of rigid, semi-rigid or flexible cellular plastics and rubbers. If the material to be tested includes skins formed during moulding, the apparent overall density or the apparent core density may be determined. Each test piece shall be of a shape, that its volume can be easily calculated.</p>"

15637,IS,,ISO 8450:1986,"Pipework — Single overlap flexible metal hoses (unpacked, no tightness, circular or polygonal section, in protected carbon steel)","Tuyauteries — Tuyaux métalliques flexibles à agrafage simple (sans joint, non étanches, section circulaire ou polygonale, en acier non allié protégé)",1986-11-27,1,['23.040.70'],ISO/TC 5/SC 11,9599,,[27752],"['en','fr']",2,<p>Specifies diameters of hoses and gives requirements to be verified in accordance with ISO 7658. Applies to uncoated hoses. A figure illustrates the meaning of the text. Gives an example of designation. The table includes nominal size from DN 6 up to and including DN 300.</p>

15642,IS,,ISO 8454:1987,Cigarettes — Determination of carbon monoxide in the vapour phase of smoke (NDIR method),Cigarettes — Dosage du monoxyde de carbone dans la phase gazeuse de la fumée de cigarette (Méthode IRND),1987-08-20,1,['65.160'],ISO/TC 126,9599,,[15643],"['en','fr']",5,

15643,IS,,ISO 8454:1995,Cigarettes — Determination of carbon monoxide in the vapour phase of cigarette smoke — NDIR method,Cigarettes — Dosage du monoxyde de carbone dans la phase gazeuse de fumée de cigarette — Méthode IRND,1995-11-02,2,['65.160'],ISO/TC 126,9599,[15642],"[34674,41168]","['en','fr']",5,"<p>Specifies a method for the determination of carbon monoxide (CO) in the vapour phase of cigarette smoke. Replaces the first edition, of which it constitutes a technical revision.</p>"

41168,IS,,ISO 8454:2007,Cigarettes — Determination of carbon monoxide in the vapour phase of cigarette smoke — NDIR method,Cigarettes — Dosage du monoxyde de carbone dans la phase gazeuse de la fumée de cigarette — Méthode IRND,2007-06-01,3,['65.160'],ISO/TC 126,9599,[15643],[85345],"['en','fr']",7,<p>ISO 8454:2007 specifies a method for the determination of carbon monoxide (CO) in the vapour phase of cigarette smoke.</p>

53045,IS,Amd,ISO 8454:2007/Amd 1:2009,Cigarettes — Determination of carbon monoxide in the vapour phase of cigarette smoke — NDIR method — Amendment 1,Cigarettes — Dosage du monoxyde de carbone dans la phase gazeuse de la fumée de cigarette — Méthode IRND — Amendement 1,2009-10-09,3,['65.160'],ISO/TC 126,9599,,[85345],"['en','fr']",1,

76550,IS,Amd,ISO 8454:2007/Amd 2:2019,Cigarettes — Determination of carbon monoxide in the vapour phase of cigarette smoke — NDIR method — Amendment 2,Cigarettes — Dosage du monoxyde de carbone dans la phase gazeuse de la fumée de cigarette — Méthode IRND — Amendement 2,2019-07-30,3,['65.160'],ISO/TC 126,9599,,[85345],"['en','fr']",1,

15644,IS,,ISO 8455:1986,Green coffee in bags — Guidance on storage and transport,Café vert en sacs — Lignes directrices pour l'entreposage et le transport,1986-03-13,1,['67.140.20'],ISO/TC 34/SC 15,9599,,[44601],"['en','fr']",3,"<p>General guidance on the conditions for minimizing the risks of infestation, contamination and quality deterioration. It describes conditions of putting into storage, conditions for storage and of maritime transit.</p>"

15646,IS,,ISO 8457-1:1989,Steel wire rod — Part 1: Dimensions and tolerances,Fil-machine en acier — Partie 1: Dimensions et tolérances,1989-06-29,1,['77.140.65'],ISO/TC 17/SC 17,9599,,[36074],"['en','fr']",4,<p>Applies to unalloyed steel wire rods for conversion to wire and to wire rods for the manufacture of welding electrodes.</p>

15647,IS,,ISO 8457-2:1989,Steel wire rod — Part 2: Quality requirements for unalloyed steel wire rods for conversion to wire,Fil-machine en acier — Partie 2: Prescriptions de qualité pour fil-machine en acier non allié destiné à la fabrication de fils,1989-08-24,1,['77.140.65'],ISO/TC 17/SC 17,9599,,"[30152,26563,30153,30150,30151]","['en','fr']",9,"<p>Applies to round, half-round, square, hexagonal, rectangular and flat wire rods with diameters of 5 mm and more for conversion to wire by cold-drawing or cold-rolling. Does not apply to wire rods intended for cold heading intended for the manufacture of welding electrodes and wire rods intended for quenching and tempering or surface hardening.

15649,IS,,ISO 8458-1:1989,Steel wire for mechanical springs — Part 1: General requirements,Fils en acier pour ressorts mécaniques — Partie 1: Caractéristiques générales,1989-06-08,1,['77.140.25'],ISO/TC 17/SC 17,9599,,[26562],"['en','fr']",3,"<p>Applies to uncoated steel spring wire of round cross-section, suitable for the manufacture of coiled springs. This part of ISO 8458 is not applicable to uncoated steel spring wire intended for use in upholstery springs or automotive valve springs.</p>"

26562,IS,,ISO 8458-1:2002,Steel wire for mechanical springs — Part 1: General requirements,Fils en acier pour ressorts mécaniques — Partie 1: Exigences générales,2002-08-15,2,['77.140.25'],ISO/TC 17/SC 17,9599,[15649],[92335],"['en','fr']",7,"<p>ISO 8458-1 specifies general requirements for steel spring wire of round cross-section, suitable for the manufacture of mechanical springs.</p>"

15650,IS,,ISO 8458-2:1989,Steel wire for mechanical springs — Part 2: Cold-drawn carbon steel wire,Fils en acier pour ressorts mécaniques — Partie 2: Fils en acier au carbone étirés à froid,1989-06-22,1,['77.140.25'],ISO/TC 17/SC 17,9599,,[30088],"['en','fr']",5,"<p>Includes carbon steel wire suitable for the manufacture of loaded springs corresponding to the general requirements of ISO 8458, part 1. Applies to certain ranges of wire diameters and tensile strength grades.</p>"

30088,IS,,ISO 8458-2:2002,Steel wire for mechanical springs — Part 2: Patented cold-drawn non-alloy steel wire,"Fils en acier pour ressorts mécaniques — Partie 2: Fils en acier non allié, patentés, tréfilés à froid",2002-08-15,2,['77.140.25'],ISO/TC 17/SC 17,9599,[15650],[92336],"['en','fr']",9,"<p>ISO 8458-2 specifies requirements for cold-drawn non-alloy steel wire for the manufacture of mechanical springs for static duty and dynamic duty applications, complying with the general requirements of ISO 8458-1.</p>"

15651,IS,,ISO 8458-3:1992,Steel wire for mechanical springs — Part 3: Oil-hardened and tempered wire,Fils en acier pour ressorts mécaniques — Partie 3: Fils trempés à l'huile et revenus,1992-11-25,1,['77.140.25'],ISO/TC 17/SC 17,9599,,[30087],"['en','fr']",7,"<p>Specifies requirements and test methods (surface condition, chemical composition, tensile strength, ductility, surface quality) for wires intended for static duty and dynamic duty applications. Wire diameters range from 0,50 mm to 15,00 mm.</p>"

30087,IS,,ISO 8458-3:2002,Steel wire for mechanical springs — Part 3: Oil-hardened and tempered wire,Fils en acier pour ressorts mécaniques — Partie 3: Fils trempés à l'huile et revenus,2002-10-25,2,['77.140.25'],ISO/TC 17/SC 17,9599,[15651],[92337],"['en','fr']",7,"<p>ISO 8458-3 specifies requirements for oil-hardened and tempered carbon and low alloy steel wire, for the manufacture of mechanical springs for static duty and dynamic duty applications, complying with the general requirements of ISO 8458-1.</p>"

15652,IS,,ISO 8459-1:1988,Documentation — Bibliographic data element directory — Part 1: Interloan applications,Documentation — Répertoire des éléments de données bibliographiques — Partie 1: Applications au prêt-inter,1988-07-07,1,['35.240.30'],ISO/TC 46/SC 4,9599,,[44937],"['en','fr']",22,<p>Specifies and describes the data elements required in the interchange of data between interlending institutions. Identifies also messages and their data elements which are used in interloan transactions. Is intended for messages communicated both by preprinted forms having the specified data element names as headings and by automated interchange processes.</p>

15653,IS,,ISO 8459-2:1992,Information and documentation — Bibliographic data element directory — Part 2: Acquisitions applications,Information et documentation — Répertoire des éléments de données bibliographique — Partie 2: Applications aux acquisitions,1992-12-03,1,['35.240.30'],ISO/TC 46/SC 4,9599,,[44937],"['en','fr']",33,"<p>Specifies and describes data elements required in the interchange of data between institutions involved in the acquisition of bibliographic materials. Also identifies messages and their data elements which are used in the acquisitions process. The data elements are presented as a data element directory, as an index consisting of names, keywords and synonyms for data

15654,IS,,ISO 8459-3:1994,Information and documentation — Bibliographic data element directory — Part 3: Information retrieval applications,Information et documentation — Répertoire des éléments de données bibliographiques — Partie 3: Applications à la recherche documentaire,1994-12-22,1,['35.240.30'],ISO/TC 46/SC 4,9599,,[44937],"['en','fr']",34,<p>Specifies and describes data elements required in the interchange of data between information retrieval systems. Also identifies messages and their data elements which are used in information retrieval transactions. Intended to support both batch and interactive information retrieval transactions.</p>

25909,IS,,ISO 8459-4:1998,Information and documentation — Bibliographic data element directory — Part 4: Circulation applications,Information et documentation — Répertoire des éléments de données bibliographiques — Partie 4: Applications à la circulation,1998-08-06,1,['35.240.30'],ISO/TC 46/SC 4,9599,,[44937],"['en','fr']",61,

27176,IS,,ISO 8459-5:2002,Information and documentation — Bibliographic data element directory — Part 5: Data elements for the exchange of cataloguing and metadata,Information et documentation — Répertoire des éléments de données bibliographiques — Partie 5: Éléments de données pour l'échange de catalogues et de métadonnées,2002-06-13,1,['35.240.30'],ISO/TC 46/SC 4,9599,,[44937],"['en','fr']",72,

5219,IS,,ISO 846:1978,Plastics — Determination of behaviour under the action of fungi and bacteria — Evaluation by visual examination or measurement of change in mass or physical properties,Plastiques — Détermination du comportement sous l'action des champignons et des bactéries — Évaluation par estimation visuelle ou par mesurage des variations de masse ou de caractéristiques physiques,1978-09-01,1,"['83.080.01','07.100.99']",ISO/TC 61/SC 6,9599,,[20578],"['en','fr']",10,

20578,IS,,ISO 846:1997,Plastics — Evaluation of the action of microorganisms,Plastiques — Évaluation de l'action des micro-organismes,1997-06-12,2,"['83.080.01','07.100.99']",ISO/TC 61/SC 6,9599,[5219],"[70278,74599]","['en','fr']",22,

15664,IS,,ISO 8466-1:1990,Water quality — Calibration and evaluation of analytical methods and estimation of performance characteristics — Part 1: Statistical evaluation of the linear calibration function,Qualité de l'eau — Étalonnage et évaluation des méthodes d'analyse et estimation des caractères de performance — Partie 1: Évaluation statistique de la fonction linéaire d'étalonnage,1990-03-01,1,['13.060.01'],ISO/TC 147/SC 2,9599,,[77139],"['en','fr']",8,<p>Describes the steps to be taken in evaluating the statistical characteristics of this function. It is applicable to methods requiring a calibration. In order to derive comparable analytical results and as a basis for analytical quality

15665,IS,,ISO 8466-2:1993,Water quality — Calibration and evaluation of analytical methods and estimation of performance characteristics — Part 2: Calibration strategy for non-linear second order calibration functions,Qualité de l'eau — Étalonnage et évaluation des méthodes d'analyse et estimation des caractères de performance — Partie 2: Stratégie d'étalonnage pour fonctions d'étalonnage non linéaires du second degré,1993-05-13,1,['13.060.01'],ISO/TC 147/SC 2,9599,,[34816],"['en','fr']",12,"<p>Is intended for use in method development and may not necessarily be applicable to all routine analyses. It is not always possible to accurately describe the relationship between a set of calibration

15668,IS,,ISO 8467:1986,Water quality — Determination of permanganate index,Qualité de l'eau — Détermination de l'indice de permanganate,1986-06-19,1,['13.060.50'],ISO/TC 147/SC 2,9599,,[15669],"['en','fr']",3,

15670,IS,,ISO 8468:1987,Ship's bridge layout and associated equipment — Requirements and guidelines,Aménagement de la passerelle d'un navire et disposition de ses équipements annexes — Exigences et directives,1987-05-28,1,['47.020.10'],ISO/TC 8/SC 6,9599,,[15671],"['en','fr']",,

15671,IS,,ISO 8468:1990,Ship's bridge layout and associated equipment — Requirements and guidelines,Aménagement de la passerelle d'un navire et disposition de ses équipements annexes — Exigences et directives,1990-11-01,2,['47.020.10'],ISO/TC 8/SC 6,9599,[15670],[43040],"['en','fr']",17,"<p>Specifies basic functional requirements for bridge configuration, bridge arrangement, bridge equipment and bridge environment. Applies to seagoing ships where bridge duty is regularly maintained. This second edition cancels and replaces the first edition (1987).</p>"

15672,IS,,ISO 8469:1994,Small craft — Non-fire-resistant fuel hoses,"Navires de plaisance — Tuyaux souples non résistants au feu, pour carburant",1994-12-22,1,['47.080'],ISO/TC 188,9599,,[37498],"['en','fr']",5,"<p>Specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol and diesel oil at low pressure, designed for a working pressure not exceeding 0,34 MPa for hoses with nominal bore up to and including 10 mm, and 0,25 MPa for hoses with a larger bore. Applies to hoses for small craft of up to 24 m length of hull with permanently installed inboard engines.</p>"

37498,IS,,ISO 8469:2006,Small craft — Non-fire-resistant fuel hoses,"Petits navires — Tuyaux souples non résistants au feu, pour carburant",2006-06-21,2,['47.080'],ISO/TC 188,9599,[15672],[59438],"['en','fr']",7,"<p>ISO 8469:2006 specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol end diesel oil designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of hull length up to 24 m.</p><p>ISO 8469:2006 applies to hoses for small craft with permanently installed fuel systems.</p><p>Specifications for fire-resistant hoses are laid down in I

59438,IS,,ISO 8469:2013,Small craft — Non-fire-resistant fuel hoses,Petits navires — Tuyaux souples pour carburant non résistants au feu,2013-07-16,3,['47.080'],ISO/TC 188,9599,[37498],[79098],"['en','fr']",8,"<p>ISO 8469:2013 specifies general requirements and physical tests for non-fire-resistant hoses for conveying petrol or petrol blended with ethanol and diesel fuel or diesel fuel blended with FAME, designed for a working pressure not exceeding 0,34 MPa for hoses with inner diameter up to and including 10 mm and 0,25 MPa for hoses up to 63 mm inner diameter in craft of hull length up to 24 m.</p><p>It applies to hoses for small craft with permanently installed fuel systems.</p><p>Specif

15673,IS,,ISO 8470:1990,"Road vehicles — M14 x 1,25 spark-plugs with flat seating and 16 mm hexagon and their cylinder head housing","Véhicules routiers — Bougies d'allumage M14 x 1,25 à siège plat et à hexagone de 16 mm et leur logement dans la culasse",1990-09-13,1,['43.060.50'],ISO/TC 22,9599,,[27838],"['en','fr']",5,

15674,IS,Amd,ISO 8470:1990/Amd 1:1993,"Road vehicles — M14 x 1,25 spark-plugs with flat seating and 16 mm hexagon and their cylinder head housing — Amendment 1","Véhicules routiers — Bougies d'allumage M14 x 1,25 à siège plat et à hexagone de 16 mm et leur logement dans la culasse — Amendement 1",1993-01-21,1,['43.060.50'],ISO/TC 22,9599,,[27838],"['en','fr']",2,

27838,IS,,ISO 8470:2001,"Road vehicles — M14 x 1,25 spark-plugs with flat seating and 16 mm hexagon and their cylinder head housings","Véhicules routiers — Bougies d'allumage M14 x 1,25 à siège plat et à hexagone de 16 mm et leurs logements dans la culasse",2001-04-05,2,['43.060.50'],ISO/TC 22,9599,"[15674,15673]",[39146],"['en','fr']",6,

15675,IS,,ISO 8471:1987,Information processing systems — Data communication — High-level data link control balanced classes of procedures — Data-link layer address resolution/negotiation in switched environments,Systèmes de traitement de l'information — Communication de données — Classes équilibrées de procédures de commande de liaison de données à haut niveau — Détermination/négociation d'adresse de couche liaison de données en environnement commuté,1987-03-26,1,['35.100.20'],ISO/IEC JTC 1/SC 6,9599,,[21474],"['en','fr']",3,

15677,IS,,ISO 8473:1988,Information processing systems — Data communications — Protocol for providing the connectionless-mode network service,Systèmes de traitement de l'information — Communications de données — Protocole fournissant le service de réseau en mode sans connexion,1988-12-29,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[20790],['en'],51,

21510,IS,Cor,ISO 8473:1988/Cor 1:1992,Information processing systems — Data communications — Protocol for providing the connectionless-mode network service — Technical Corrigendum 1,Systèmes de traitement de l'information — Communications de données — Protocole fournissant le service de réseau en mode sans connexion — Rectificatif technique 1,1992-12-10,1,['35.100.30'],ISO/IEC JTC 1/SC 6,9599,,[20790],"['en','fr']",1,

15685,IS,,ISO 8478:1996,Photography — Camera lenses — Measurement of ISO spectral transmittance,Photographie — Objectifs photographiques — Mesurage du facteur spectral de transmission ISO,1996-11-28,1,['37.040.10'],ISO/TC 172/SC 1,9599,,[72599],['en'],7,<p>Gives a method for measuring the spectral transmittance of camera lenses. Describes particular conditions for measuring the axial spectral transmittance over a wavelength range from 350 nm to 700 nm of camera lenses which are to be used mainly for taking pictures of very distant objects.</p>

15687,IS,,ISO 8480:1987,Information processing — Data communication — DTE/DCE interface back-up control operation using the 25-pole connector,Traitement de l'information — Communication de données — Dispositif de secours à la jonction ETTD/ETCD réalisé à l'aide du connecteur à 25 broches,1987-11-05,1,['35.100.10'],ISO/IEC JTC 1/SC 6,9599,,[24074],"['en','fr']",7,

15688,IS,,ISO 8481:1986,Data communication — DTE to DTE physical connection using X.24 interchange circuits with DTE provided timing,Communication de données — Connexion physique d'ETTD vers ETTD utilisant les circuits de jonction X.24 avec une base de temps fournie par l'ETTD,1986-09-18,1,['35.100.10'],ISO/IEC JTC 1/SC 6,9599,,[26137],"['en','fr']",3,

15689,IS,,ISO 8482:1987,Information processing systems — Data communication — Twisted pair multipoint interconnections,Systèmes de traitement de l'information — Communication de données — Interconnexions multipoints par paire torsadée,1987-11-12,1,['35.100.10'],ISO/IEC JTC 1/SC 6,9599,,[20954],['en'],16,

33015,IS,,ISO 8483:2003,Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints,Tubes et raccords en plastiques thermodurcissables renforcés de verre (PRV) — Méthode d'essai pour confirmer la conception des assemblages à brides boulonnées,2003-11-21,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,,[67697],['en'],11,"<p>ISO 8483:2003 specifies methods of test for bolted flange joints for plastics piping systems made of glass-reinforced thermosetting plastics (GRP). This standard is only applicable to the joint, and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subj

56678,IS,Amd,ISO 8483:2003/Amd 1:2012,Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints — Amendment 1,Tubes et raccords en plastiques thermodurcissables renforcés de verre (PRV) — Méthode d'essai pour confirmer la conception des assemblages à brides boulonnées — Amendement 1,2012-01-24,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,,[67697],['en'],2,

15691,IS,,ISO 8484:1987,Magnetic stripes on savingsbooks,Zone magnétique des livrets d'épargne,1987-07-02,1,['35.240.40'],ISO/IEC JTC 1/SC 17,9599,,[39700],"['en','fr']",6,"<p>Specifies the location, dimensions, electromanetic properties, recording characteristics, character coding and character set of magnetic stripes on savingsbooks used in interchange. Describes features of the savingsbook cover i.e. stiffness, minimum dimensions, surface irregularities, roughness as well as the interaction between cover material and magnetic stripe. References: ISO 7811-2 and -5, TAPPI T489 os-76.</p>"

15693,IS,,ISO 8486:1986,Bonded abrasives — Grain size analysis — Designation and determination of grain size distribution of macrogrits F4 to F220,Abrasifs agglomérés — Granulométrie — Désignation et détermination de la distribution granulométrique des macrograins de F4 à F220,1986-03-27,1,['25.100.70'],ISO/TC 29/SC 5,9599,,"[15695,15696]",['en'],3,

15696,IS,,ISO 8486-2:1996,Bonded abrasives — Determination and designation of grain size distribution — Part 2: Microgrits F230 to F1200,Abrasifs agglomérés — Détermination et désignation de la distribution granulométrique — Partie 2: Micrograins F230 à F1200,1996-08-15,1,['25.100.70'],ISO/TC 29/SC 5,9599,[15693],[42206],"['en','fr']",25,<p>Contains a method for the determination or for checking the size distribution of macrogrits from F230 to F1200 in fused aluminium oxide and silicon carbide used in the manufacture of bonded abrasives.</p>

15699,IS,,ISO 8489-1:1985,"Textile machinery and accessories — Cones for cross-wound winding — Part 1: Values of half-angles, lengths and large inner diameters","Matériel pour l'industrie textile — Cônes pour bobinage croisé — Partie 1: Valeurs des demi-angles, longueurs et grands diamètres intérieurs",1985-07-18,1,['59.120.20'],ISO/TC 72/SC 1,9599,,[21960],"['en','fr']",2,

15700,IS,,ISO 8490:1986,Metallic materials — Sheet and strip — Modified Erichsen cupping test,Matériaux métalliques — Tôles et bandes — Essai d'emboutissage Erichsen modifié,1986-10-02,1,['77.040.10'],ISO/TC 164/SC 2,9599,[3978],[34186],"['en','fr']",4,"<p>Specifies a method for determining the ability of sheets and strips having a thickness from 0,2 up to 2 mm and a width of 90 mm or more to undergo plastic deformation in stretch drawing, The test is referred to as the modified Erichsen cupping test as, in the test as originally introduced, no blank holder pressure was used but, in the interests of obtaining greater consistency of results, this was changed.</p>"

15701,IS,,ISO 8491:1986,Metallic materials — Tube (in full section) — Bend test,Matériaux métalliques — Tubes — Essai de cintrage sur tronçon,1986-10-02,1,['77.040.10'],ISO/TC 164/SC 2,9599,[4001],[30444],"['en','fr']",2,

15702,IS,,ISO 8492:1986,Metallic materials — Tube — Flattening test,Matériaux métalliques — Tubes — Essai d'aplatissement,1986-10-02,1,['77.040.10'],ISO/TC 164/SC 2,9599,"[6146,4067,5379]",[30445],"['en','fr']",2,

30445,IS,,ISO 8492:1998,Metallic materials — Tube — Flattening test,Matériaux métalliques — Tubes — Essai d'aplatissement,1998-10-22,2,['77.040.10'],ISO/TC 164/SC 2,9599,"[22828,15702]",[63853],"['en','fr']",2,

15703,IS,,ISO 8493:1986,Metallic materials — Tube — Drift-expanding test,Matériaux métalliques — Tubes — Essai d'évasement,1986-10-02,1,['77.040.10'],ISO/TC 164/SC 2,9599,"[5377,4049,4000]",[30446],['en'],2,

15704,IS,,ISO 8494:1986,Metallic materials — Tube — Flanging test,Matériaux métalliques — Tubes — Essai de rabattement de collerette,1986-10-16,1,['77.040.10'],ISO/TC 164/SC 2,9599,[3999],[30447],"['en','fr']",2,

30447,IS,,ISO 8494:1998,Metallic materials — Tube — Flanging test,Matériaux métalliques — Tubes — Essai de rabattement de collerette,1998-10-22,2,['77.040.10'],ISO/TC 164/SC 2,9599,"[22830,15704]",[63854],"['en','fr']",3,

15705,IS,,ISO 8495:1986,Metallic materials — Tube — Ring-expanding test,Matériaux métalliques — Tubes — Essai de dilatation d'anneaux,1986-10-02,1,['77.040.10'],ISO/TC 164/SC 2,9599,[4350],[30448],"['en','fr']",2,

30448,IS,,ISO 8495:1998,Metallic materials — Tube — Ring-expanding test,Matériaux métalliques — Tubes — Essai de dilatation d'anneaux,1998-10-22,2,['77.040.10'],ISO/TC 164/SC 2,9599,"[15705,25539]",[63855],"['en','fr']",3,

15706,IS,,ISO 8496:1986,Metallic materials — Tube — Ring tensile test,Matériaux métalliques — Tubes — Essai de traction sur anneaux,1986-10-09,1,['77.040.10'],ISO/TC 164/SC 2,9599,,[30449],"['en','fr']",2,

30449,IS,,ISO 8496:1998,Metallic materials — Tube — Ring tensile test,Matériaux métalliques — Tubes — Essai de traction sur anneaux,1998-10-22,2,['77.040.10'],ISO/TC 164/SC 2,9599,"[25540,15706]",[63856],"['en','fr']",2,

15709,IS,,ISO 8499:1990,Knitted fabrics — Description of defects — Vocabulary,Étoffes tricotées — Description des défauts — Vocabulaire,1990-03-08,1,"['59.080.30','01.040.59']",ISO/TC 38/SC 20,9599,,[37071],"['en','fr']",16,

15711,IS,,ISO 8501-1:1988,Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Évaluation visuelle de la propreté d'un subjectile — Partie 1: Degrés de rouille et degrés de préparation des subjectiles d'acier non recouverts et des subjectiles d'acier après décapage sur toute la surface des revêtements précédents,1988-12-29,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[43426],"['en','fr','ru']",134

15713,IS,Suppl,ISO 8501-1:1988/Suppl:1994,Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings — Supplement: Representative photographic examples of the change of appearance imparted to steel when blast-cleaned with different abrasives,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Évaluation visuelle de la propreté d'un subjectile — Partie 1: Degrés de rouille et degrés de préparation des subjectiles d'acier non recouverts et des subje

21193,IS,,ISO 8501-3:2001,"Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 3: Preparation grades of welds, cut edges and other areas with surface imperfections","Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Évaluation visuelle de la propreté d'un subjectile — Partie 3: Degrés de préparation des soudures, arêtes de coupe et autres zones présentant des imperfections",2001-12-20,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[41021],"['en','fr']",5,

41021,IS,,ISO 8501-3:2006,"Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 3: Preparation grades of welds, edges and other areas with surface imperfections","Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Évaluation visuelle de la propreté d'un subjectile — Partie 3: Degrés de préparation des soudures, arêtes et autres zones présentant des imperfections",2006-03-03,2,['25.220.10'],ISO/TC 35/SC 12,9599,[21193],[78818],"['en','fr']",6,"<p>ISO 8501-3:2006 describes preparation grades of welds, cut edges and other areas, on steel surfaces with imperfections. Such imp

38146,IS,,ISO 8501-4:2006,"Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting","Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Évaluation visuelle de la propreté d'un subjectile — Partie 4: États de surface initiaux, degrés de préparation et degrés de fleurette de rouille après décapage à l'eau sous haute pression",2006-12-19,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[73861],"['de','en','fr','ru']",92,"<p>ISO 8501-4:2006 is a hardback A5-format book in

27606,IS,,ISO 8502-11:2006,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 11: Field method for the turbidimetric determination of water-soluble sulfate,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 11: Méthode in situ pour la détermination turbidimétrique des sulfates hydrosolubles,2006-03-20,1,['25.220.10'],ISO/TC 35/SC 12,9599,,"[59854,78816]","['en','fr','ru']",5,<p>ISO 8502-11:2006 describes a field method for the assessment of the surface density of water-soluble sulfate on steel surfaces befo

27607,IS,,ISO 8502-12:2003,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 12: Field method for the titrimetric determination of water-soluble ferrous ions,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 12: Méthode in situ pour la détermination titrimétrique des ions ferreux hydrosolubles,2003-02-12,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[60140],"['en','fr','ru']",4,"<p>ISO 8502:2003 describes a field method for the determination, by drop titration, of soluble ferrous ions on steel surfaces before and

15716,IS,,ISO 8502-2:1992,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 2: Laboratory determination of chloride on cleaned surfaces,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'un subjectile — Partie 2: Recherche des chlorures sur les surfaces nettoyées,1992-06-11,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[37491],"['en','fr']",3,<p>Describes a method for assessment of chloride-containing salts that are readily soluble in water and are present on a steel surface or on a previously coated surface. The method cannot be used

37491,IS,,ISO 8502-2:2005,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 2: Laboratory determination of chloride on cleaned surfaces,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 2: Recherche en laboratoire des chlorures sur les surfaces nettoyées,2005-10-14,2,['25.220.10'],ISO/TC 35/SC 12,9599,[15716],[58058],"['en','fr','ru']",6,"<p>ISO 8502-2:2005 describes a method for the determination of chloride-containing salts that are readily soluble in water and are present on a steel surface. The method

15717,IS,,ISO 8502-3:1992,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method),Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'un subjectile — Partie 3: Évaluation de la poussière sur les surfaces d'acier préparées pour la mise en peinture (méthode du ruban adhésif sensible à la pression),1992-10-01,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[58060],"['en','fr']",8,"<p>Provides pictorial ratings for the assessment of the average quantity

15718,IS,,ISO 8502-4:1993,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 4: Guidance on the estimation of the probability of condensation prior to paint application,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 4: Principes directeurs pour l'estimation de la probabilité de condensation avant application de peinture,1993-04-08,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[58061],"['en','fr']",14,"<p>May be used to establish whether conditions at the job site are suitable for painting or not. The method spe

21031,IS,,ISO 8502-5:1998,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 5: Measurement of chloride on steel surfaces prepared for painting (ion detection tube method),Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 5: Mesurage des chlorures sur les surfaces d'acier préparées pour la mise en peinture (méthode du tube détecteur d'ions),1998-02-05,1,['25.220.10'],ISO/TC 35/SC 12,9599,,"[63163,83009,78817]","['en','fr']",5,

21032,IS,,ISO 8502-6:1995,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 6: Extraction of soluble contaminants for analysis — The Bresle method,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 6: Extraction des contaminants solubles en vue de l'analyse — Méthode de Bresle,1995-12-21,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[42962],"['en','fr']",6,"<p>Describes a method of extraction, intended for analysis, of soluble contaminants from a surface by means of adhesive patches which can be attached to any su

42962,IS,,ISO 8502-6:2006,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 6: Extraction of soluble contaminants for analysis — The Bresle method,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 6: Extraction des contaminants solubles en vue de l'analyse — Méthode de Bresle,2006-06-21,2,['25.220.10'],ISO/TC 35/SC 12,9599,[21032],"[73862,59852]","['en','fr','ru']",7,"<p>ISO 8502-6:2006 describes a method of extracting, for analysis, soluble contaminants from a surface by use of flexible cells in the form

20047,IS,,ISO 8502-8:2001,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 8: Field method for the refractometric determination of moisture,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 8: Méthode in situ pour la détermination réfractométrique de l'humidité,2001-08-23,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[60141],"['en','fr','ru']",6,

2833,IS,,ISO 8502-9:1998,Preparation of steel substrates before application of paints and related products — Tests for the assessment of surface cleanliness — Part 9: Field method for the conductometric determination of water-soluble salts,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Essais pour apprécier la propreté d'une surface — Partie 9: Méthode in situ pour la détermination des sels solubles dans l'eau par conductimétrie,1998-04-23,1,['25.220.10'],ISO/TC 35/SC 12,9599,,"[58062,73863]","['en','fr']",5,

15720,IS,,ISO 8503-1:1988,Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Caractéristiques de rugosité des subjectiles d'acier décapés — Partie 1: Spécifications et définitions relatives aux échantillons de comparaison viso-tactile ISO pour caractériser les surfaces préparées par projection d'abrasif,1988-01-28,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[51979],"['en','fr']

15721,IS,,ISO 8503-2:1988,Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Caractéristiques de rugosité des subjectiles d'acier décapés — Partie 2: Méthode pour caractériser un profil de surface en acier décapée par projection d'abrasif — Utillisation d'échantillons de comparaison viso-tactile ISO,1988-01-28,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[51980],"['en','fr']",3,<p>Describes a visual an

15722,IS,,ISO 8503-3:1988,Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Focusing microscope procedure,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Caractéristiques de rugosité des subjectiles d'acier décapés — Partie 3: Méthode pour étalonner les échantillons de comparaison viso-tactile ISO et pour caractériser un profil de surface — Utilisation d'un microscope optique,1988-01-28,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[5198

15723,IS,,ISO 8503-4:1988,Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Stylus instrument procedure,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Caractéristiques de rugosité des subjectiles d'acier décapés — Partie 4: Méthode pour étalonner les échantillons de comparaison viso-tactile ISO et pour caractériser un profil de surface — Utilisation d'un appareil à palpeur,1988-01-28,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[51982]

28622,IS,,ISO 8503-5:2003,Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 5: Replica tape method for the determination of the surface profile,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Caractéristiques de rugosité des subjectiles d'acier décapés — Partie 5: Méthode de l'empreinte sur ruban adhésif pour la détermination du profil de surface,2003-07-15,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[60139],"['en','fr']",7,"<p>ISO 8503-5:2003 describes a field method for measuring the surface profile produced by any of the abrasive blast-cleani

15725,IS,,ISO 8504-1:1992,Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 1: General principles,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes de préparation des subjectiles — Partie 1: Principes généraux,1992-12-03,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[29750],"['en','fr']",4,

29750,IS,,ISO 8504-1:2000,Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 1: General principles,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes de préparation des subjectiles — Partie 1: Principes généraux,2000-03-09,2,['25.220.10'],ISO/TC 35/SC 12,9599,[15725],[72938],"['en','fr']",6,<p>This part of ISO 8504 describes the general principles for the selection of methods for the preparation of steel surfaces before application of paints and related products. It also contains information on features that must be taken into account before certain surface preparation meth

15726,IS,,ISO 8504-2:1992,Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 2: Abrasive blast-cleaning,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes de préparation des subjectiles — Partie 2: Décapage par projection d'abrasif,1992-12-03,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[29751],"['en','fr']",9,

29751,IS,,ISO 8504-2:2000,Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 2: Abrasive blast-cleaning,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes de préparation des subjectiles — Partie 2: Décapage par projection d'abrasif,2000-03-09,2,['25.220.10'],ISO/TC 35/SC 12,9599,[15726],[72939],"['en','fr']",13,"<p>This part of ISO 8504 describes abrasive blast-cleaning methods for the preparation of steel surfaces before coating with paints and related products. It also contains information on the effectiveness of the individual methods and their fields of application.</p>

15727,IS,,ISO 8504-3:1993,Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 3: Hand- and power-tool cleaning,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes de préparation des subjectiles — Partie 3: Nettoyage à la main et à la machine,1993-07-29,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66696],"['en','fr']",4,"<p>Describes the equipment to be used and the procedure to be followed. Applies both to new steelwork and to steel surfaces that have been coated previously and that show areas of breakdown requiring maintenance painting. Annexes A and B describe types of hand tools

15730,IS,,ISO 8507:1986,Agglomerated cork discs — Methods of test,Disques en aggloméré composé de liège — Méthodes d'essai,1986-12-11,1,['79.100'],ISO/TC 87,9599,,[21018],"['en','fr']",5,

15733,IS,,ISO 8510-1:1990,Adhesives — Peel test for a flexible-bonded-to-rigid test specimen assembly — Part 1: 90 degree peel,Adhésifs — Essai de pelage pour un assemblage collé flexible-sur-rigide — Partie 1: Pelage à 90 degrés,1990-12-13,1,['83.180'],ISO/TC 61/SC 11,9599,,[43774],"['en','fr']",5,"<p>Particularly suitable for use with less flexible adherends for which a 180 ° peel test is not suitable because the adherends crack, break or delaminate. A bonded assembly of two adherends is prepared using the adhesive under test. The adherends are then pulled apart at a steady rate, starting at the open end of the bond, in such a way that separation occurs progressively along the length of th

15734,IS,,ISO 8510-2:1990,Adhesives — Peel test for a flexible-bonded-to-rigid test specimen assembly — Part 2: 180 degree peel,Adhésifs — Essai de pelage pour un assemblage collé flexible-sur-rigide — Partie 2: Pelage à 180 degrés,1990-12-13,1,['83.180'],ISO/TC 61/SC 11,9599,,[43775],"['en','fr']",5,"<p>Suitable for use with less flexible adherends. The principle consists in preparing a bonded assembly of two adherends, using the adhesive under test. The adherends are then pulled apart at a steady rate, starting at the open end of the bond, in such a way that separation occurs progressively along the length of the bonded adherends. The force is applied substantially parallel to the plane of

15735,IS,,ISO 8511:1987,Rubber compounding ingredients — Carbon black — Determination of pellet size distribution,Ingrédients de mélange du caoutchouc — Noir de carbone — Détermination de la distribution granulométrique,1987-06-18,1,['83.040.20'],ISO/TC 45/SC 3,9599,,[21881],"['en','fr']",2,

21881,IS,,ISO 8511:1995,Rubber compounding ingredients — Carbon black — Determination of pellet size distribution,Ingrédients de mélange du caoutchouc — Noir de carbone — Détermination de la distribution granulométrique,1995-11-09,2,['83.040.20'],ISO/TC 45/SC 3,9599,[15735],[57933],"['en','fr']",4,<p>Gives a method for the determination of the pellet size distribution of carbon black. Replaces the first edition which has been technically revised.</p>