Withdrawn and superseded ISO standards — page 17 of 246

19120,IS,,ISO 11125-6:1993,Preparation of steel substrates before application of paints and related products — Test methods for metallic blast-cleaning abrasives — Part 6: Determination of foreign matter,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs métalliques destinés à la préparation par projection — Partie 6: Détermination des matières étrangères,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66702],"['en','fr']",3,"<p>Specifies a test method for the determination of particles with cracks, laminations, voids and shrinkage, of defectively shaped shot, grit and cylindrical particles, of microstructure. Annex

19121,IS,,ISO 11125-7:1993,Preparation of steel substrates before application of paints and related products — Test methods for metallic blast-cleaning abrasives — Part 7: Determination of moisture,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs métalliques destinés à la préparation par projection — Partie 7: Détermination de l'humidité,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66703],"['en','fr']",3,<p>Specifies a test method for the determination of the level of free moisture present determined by measuring the mass lost on heating. Annex A gives information on the international standards series for metall

19125,IS,,ISO 11126-1:1993,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 1: General introduction and classification,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 1: Introduction générale et classification,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66708],"['en','fr']",4,"<p>Describes a classification and specifies the characteristics which are required for the complete designation of such abrasives. Applies to abrasives supplied in the 'new' or

28334,IS,Cor,ISO 11126-1:1993/Cor 1:1997,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 1: General introduction and classification — Technical Corrigendum 1,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 1: Introduction générale et classification — Rectificatif technique 1,1997-02-13,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66708],"['en','fr']",2,<p>Replaces the existing table 1.</p>

28993,IS,Cor,ISO 11126-1:1993/Cor 2:1997,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 1: General introduction and classification — Technical Corrigendum 2,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 1: Introduction générale et classification — Rectificatif technique 2,1997-05-22,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66708],"['en','fr']",1,

66708,IS,,ISO 11126-1:2018,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 1: General introduction and classification,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 1: Introduction générale et classification,2018-08-24,2,['25.220.10'],ISO/TC 35/SC 12,9599,"[19125,28334,28993]",[87230],"['en','fr']",6,"<p>This document describes a classification of non-metallic blast-cleaning abrasives for the preparation of steel substrates before application of paints a

19135,IS,,ISO 11126-10:2000,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 10: Almandite garnet,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 10: Almandite,2000-08-17,1,['25.220.10'],ISO/TC 35/SC 12,9599,,"[60138,65967]","['en','fr']",4,

65967,IS,,ISO 11126-10:2017,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 10: Almandite garnet,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 10: Almandite,2017-11-06,2,['25.220.10'],ISO/TC 35/SC 12,9599,[19135],[88989],"['en','fr']",4,"<p>ISO 11126-10:2017 specifies requirements for almandite garnet abrasives, as supplied for blast-cleaning. It specifies ranges of particle sizes and values for apparent density, Mohs hardness, moisture content, conduct

19127,IS,,ISO 11126-3:1993,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 3: Copper refinery slag,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 3: Scories de raffinage du cuivre,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66709],"['en','fr']",4,"<p>Specifies requirements for copper refinery slag abrasives: designation, sampling, identification and marking, information to be supplied by the manufacturer or supplier, ranges of particle sizes and va

19128,IS,,ISO 11126-4:1993,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 4: Coal furnace slag,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 4: Cendres fondues,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66710],"['en','fr']",4,"<p>Specifies requirements for coal furnace slag abrasives: designation, sampling, identification and marking, information to be supplied by the manufacturer or supplier, ranges of particle sizes and values for apparent den

19129,IS,,ISO 11126-5:1993,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 5: Nickel refinery slag,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 5: Scories de raffinage du nickel,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66711],"['en','fr']",4,"<p>Specifies requirements for nickel refinery slag abrasives: designation, sampling, identification and marking, information to be supplied by the manufacturer or supplier, ranges of particle sizes and va

19130,IS,,ISO 11126-6:1993,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 6: Iron furnace slag,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 6: Scories de four de métallurgie,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66712],"['en','fr']",4,"<p>Specifies requirements for iron furnace slag abrasives: designation, sampling, identification and marking, information to be supplied by the manufacturer or supplier, ranges of particle sizes and values f

19131,IS,,ISO 11126-7:1995,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 7: Fused aluminium oxide,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 7: Oxyde d'aluminium fondu,1995-12-14,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66713],"['en','fr']",4,"<p>Gives requirements for blast-cleaning abrasives from fused aluminium oxide (corundum). Specifies ranges of particle sizes and values for apparent density, bulk density, Mohs hardness, moisture content, condu

31675,IS,Cor,ISO 11126-7:1995/Cor 1:1999,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 7: Fused aluminium oxide — Technical Corrigendum 1,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 7: Oxyde d'aluminium fondu — Rectificatif technique 1,1999-02-25,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66713],"['en','fr']",1,

19132,IS,,ISO 11126-8:1993,Preparation of steel substrates before application of paints and related products — Specifications for non-metallic blast-cleaning abrasives — Part 8: Olivine sand,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Spécifications pour abrasifs non métalliques destinés à la préparation par projection — Partie 8: Sable d'olivine,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[66714],"['en','fr']",4,"<p>Specifies requirements for olivine sand abrasives: designation, sampling, identification and marking, information to be supplied by the manufacturer or supplier, ranges of particle sizes and values for apparent density, Mohs

19137,IS,,ISO 11127-1:1993,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 1: Sampling,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 1: Échantillonnage,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[52003],"['en','fr']",5,<p>Specifies a method for the sampling from consignments and for the subdivision of the sample into quantities suitable for undertaking the appropriate test methods specified in other parts of ISO 11127.</p>

52003,IS,,ISO 11127-1:2011,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 1: Sampling,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 1: Échantillonnage,2011-12-06,2,['25.220.10'],ISO/TC 35/SC 12,9599,[19137],[75978],"['en','fr']",5,<p>ISO 11127-1:2011 specifies a method for the sampling of non-metallic blast-cleaning abrasives from consignments and for the subdivision of the sample into quantities suitable for undertaking the appropriate test methods sp

19138,IS,,ISO 11127-2:1993,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 2: Determination of particle size distribution,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 2: Analyse granulométrique,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[52004],"['en','fr']",3,"<p>The procedure includes weighing out a test portion of approximately 300 g of the sample, placing the test portion in the top sieve of a set of test sieves (including all the sieves list

52004,IS,,ISO 11127-2:2011,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 2: Determination of particle size distribution,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 2: Analyse granulométrique,2011-12-06,2,['25.220.10'],ISO/TC 35/SC 12,9599,[19138],[75979],"['en','fr']",4,<p>ISO 11127-2:2011 specifies a method for the determination of the particle size distribution of non-metallic blast-cleaning abrasives by sieving.</p>

19139,IS,,ISO 11127-3:1993,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 3: Determination of apparent density,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 3: Détermination de la masse volumique apparente,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[52005],"['en','fr']",3,"<p>The procedure includes drying a sufficient quantity of the sample by heating, allowing to cool to room temperature, adding distilled or deionized water to the cleaned, dried

52005,IS,,ISO 11127-3:2011,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 3: Determination of apparent density,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 3: Détermination de la masse volumique apparente,2011-12-06,2,['25.220.10'],ISO/TC 35/SC 12,9599,[19139],[75980],"['en','fr']",4,<p>ISO 11127-3:2011 specifies a method for the determination of the apparent density of non-metallic blast-cleaning abrasives.</p>

19141,IS,,ISO 11127-4:1993,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 4: Assessment of hardness by a glass slide test,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 4: Évaluation de la dureté au moyen d'un essai à la lame de verre,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[52006],"['en','fr']",3,"<p>The procedure includes examining a small quantity of the sample under the microscope and, if grains of different colours or diameter are present,

52006,IS,,ISO 11127-4:2011,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 4: Assessment of hardness by a glass slide test,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 4: Évaluation de la dureté au moyen d'un essai à la lame de verre,2011-12-06,2,['25.220.10'],ISO/TC 35/SC 12,9599,[19141],[75981],"['en','fr']",3,<p>ISO 11127-4:2011 specifies a method of assessing whether a non-metallic blast-cleaning abrasive has a minimum hardness of 6 on Mohs' scale.

19142,IS,,ISO 11127-5:1993,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 5: Determination of moisture,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 5: Détermination de l'humidité,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[52007],"['en','fr']",3,"<p>The procedure includes weighing a test portion of approximately 100 g into a container, placing the container with the test portion in an oven previously adjusted to 110 °C, leaving for at least 1 h,

52007,IS,,ISO 11127-5:2011,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 5: Determination of moisture,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 5: Détermination de l'humidité,2011-12-06,2,['25.220.10'],ISO/TC 35/SC 12,9599,[19142],[75982],"['en','fr']",3,<p>ISO 11127-5:2011 specifies a method for the determination of the level of free moisture present in non-metallic blast-cleaning abrasives. It is determined by measuring the mass lost on heating.

19143,IS,,ISO 11127-6:1993,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 6: Determination of water-soluble contaminants by conductivity measurement,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 6: Détermination des contaminants solubles dans l'eau par conductimétrie,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[52008],"['en','fr']",3,"<p>The procedure includes weighing a test portion of 100 g of the sample, adding 100 ml of the conductivity water,

52008,IS,,ISO 11127-6:2011,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 6: Determination of water-soluble contaminants by conductivity measurement,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 6: Détermination des contaminants solubles dans l'eau par conductimétrie,2011-12-06,2,['25.220.10'],ISO/TC 35/SC 12,9599,[19143],[75983],"['en','fr']",3,<p>ISO 11127-6:2011 specifies a method for the determination of water-soluble contaminants in non-metallic b

19144,IS,,ISO 11127-7:1993,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 7: Determination of water-soluble chlorides,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 7: Détermination des chlorures solubles dans l'eau,1993-12-09,1,['25.220.10'],ISO/TC 35/SC 12,9599,,[52009],"['en','fr']",3,"<p>The procedure includes weighing a test portion of 100 g of the sample, adding 100 ml of water, shaking, allowing to settle, filtering if necessary, adding sulfuric

52009,IS,,ISO 11127-7:2011,Preparation of steel substrates before application of paints and related products — Test methods for non-metallic blast-cleaning abrasives — Part 7: Determination of water-soluble chlorides,Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection — Partie 7: Détermination des chlorures solubles dans l'eau,2011-12-06,2,['25.220.10'],ISO/TC 35/SC 12,9599,[19144],[75984],"['en','fr']",3,<p>ISO 11127-7:2011 specifies a method for the determination of water-soluble chlorides in non-metallic blast-cleaning abrasives.</p>

19149,IS,,ISO 11130:1999,Corrosion of metals and alloys — Alternate immersion test in salt solution,Corrosion des métaux et alliages — Essai en immersions alternées en solution saline,1999-09-02,1,['77.060'],ISO/TC 156,9599,,[50380],"['en','fr']",12,

50380,IS,,ISO 11130:2010,Corrosion of metals and alloys — Alternate immersion test in salt solution,Corrosion des métaux et alliages — Essai en immersions alternées en solution saline,2010-06-01,2,['77.060'],ISO/TC 156,9599,[19149],[71867],"['en','fr','ru']",14,"<p>ISO 11130:2010 specifies a method for assessing the corrosion resistance of metals by an alternate immersion test in salt solution, with or without applied stress.</p><p>The test is particularly suitable for quality control during the manufacture of metals including aluminium alloys and ferrous materials, and also for assessment purposes during alloy development.</p><p>Depending upon the chemical composition of the test solution,

50124,IS,,ISO 11132:2012,Sensory analysis — Methodology — Guidelines for monitoring the performance of a quantitative sensory panel,Analyse sensorielle — Méthodologie — Lignes directrices pour le contrôle de la performance d'un jury sensoriel quantitatif,2012-10-29,1,['67.240'],ISO/TC 34/SC 12,9599,,[76669],"['en','fr','ru']",23,"<p>ISO 11132:2012 gives guidelines for monitoring and assessing the overall performance of a quantitative descriptive panel and the performance of each member.</p><p>A panel of assessors can be used as an instrument to assess the magnitude of sensory attributes.</p><p>Performance is the measure of the ability of a panel or an assessor to make valid attribute assessm

19153,IS,,ISO 11134:1994,Sterilization of health care products — Requirements for validation and routine control — Industrial moist heat sterilization,Stérilisation des produits de santé — Prescriptions pour la validation et le contrôle de routine — Stérilisation industrielle à la vapeur d'eau,1994-01-27,1,['11.080.01'],ISO/TC 198,9599,,"[31459,43187]",['en'],22,"<p>Specifies requirements for the use of moist heat in sterilization process development, validation of the sterilization process and control of routine sterilization. Covers all moist heat processes, including saturated steam and air-steam mixtures, and applies to all industrial manufacturers and all others who perform contract moi

43185,IS,,ISO 11135-1:2007,"Sterilization of health care products — Ethylene oxide — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices","Stérilisation des produits de santé — Oxyde d'éthylène — Partie 1: Exigences de développement, de validation et de contrôle de routine d'un processus de stérilisation pour des dispositifs médicaux",2007-04-27,1,['11.080.01'],ISO/TC 198,9599,"[24811,19154]",[56137],"['en','fr','ru']",41,"<p>ISO 11135-1:2007 specifies requirements for the development, validation and routine control of an ethylene oxide<i> </i>sterilization process for medical devices.</p><p>Sterilization processes validated and

19154,IS,,ISO 11135:1994,Medical devices — Validation and routine control of ethylene oxide sterilization,Dispositifs médicaux — Validation et contrôle de routine de la stérilisation à l'oxyde d'éthylène,1994-01-27,1,['11.080.01'],ISO/TC 198,9599,,"[43185,43186]","['en','fr']",24,"<p>Establishes requirements and guidance. Particular attention is drawn to the need for specific testing for safety, quality and efficacy, possibly exceeding the general requirements, which may be necessary for a speci

24811,IS,Cor,ISO 11135:1994/Cor 1:1994,Medical devices — Validation and routine control of ethylene oxide sterilization — Technical Corrigendum 1,Dispositifs médicaux — Validation et contrôle de routine de la stérilisation à l'oxyde d'éthylène — Rectificatif technique 1,1994-10-27,1,['11.080.01'],ISO/TC 198,9599,,"[43185,43186]",['en'],1,<p>Replaces the penultimate equation on page 20 by a new equation.</p>

33952,IS,,ISO 11137-1:2006,"Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices","Stérilisation des produits de santé — Irradiation — Partie 1: Exigences relatives à la mise au point, à la validation et au contrôle de routine d'un procédé de stérilisation pour les dispositifs médicaux",2006-04-19,1,['11.080.01'],ISO/TC 198,9599,"[19156,28900,33832]","[62175,81721]","['en','fr']",3

60165,IS,Amd,ISO 11137-1:2006/Amd 1:2013,"Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 1","Stérilisation des produits de santé — Irradiation — Partie 1: Exigences relatives à la mise au point, à la validation et au contrôle de routine d'un procédé de stérilisation pour les dispositifs médicaux — Amendement 1",2013-07-16,1,['11.080.01'],ISO/TC 198,9599,,"[62175,8

72106,IS,Amd,ISO 11137-1:2006/Amd 2:2018,"Sterilization of health care products — Radiation — Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices — Amendment 2: Revision to 4.3.4 and 11.2","Stérilisation des produits de santé — Irradiation — Partie 1: Exigences relatives à la mise au point, à la validation et au contrôle de routine d'un procédé de stérilisation pour les dispositifs médicaux — Amendement 2: Révision de 4.3.4 et de 1

19156,IS,,ISO 11137:1995,Sterilization of health care products — Requirements for validation and routine control — Radiation sterilization,Stérilisation des dispositifs médicaux — Prescriptions pour la validation et le contrôle de routine — Stérilisation par irradiation,1995-03-09,1,['11.080.01'],ISO/TC 198,9599,,"[33953,31460,33955,33952]","['en','fr']",61,"<p>Specifies requirements for validation, process control and routine monitoring in the radiation sterilization of health care products. Applies to continuous and batch type gamma irradiators using the radionuclides 60 Co and 137 Cs, and to irradiators using a beam from an electron or x-ray generator. Does not cover facility design, lice

33832,IS,Amd,ISO 11137:1995/Amd 1:2001,Sterilization of health care products — Requirements for validation and routine control — Radiation sterilization — Amendment 1: Selection of items for dose setting,Stérilisation des dispositifs médicaux — Prescriptions pour la validation et le contrôle de routine — Stérilisation par irradiation — Amendement 1: Sélection des articles pour le choix de la dose,2001-12-13,1,['11.080.01'],ISO/TC 198,9599,,"[33953,33955,33952]","['en','fr']",2,

28900,IS,Cor,ISO 11137:1995/Cor 1:1997,Sterilization of health care products — Requirements for validation and routine control — Radiation sterilization — Technical Corrigendum 1,Stérilisation des dispositifs médicaux — Prescriptions pour la validation et le contrôle de routine — Stérilisation par irradiation — Rectificatif technique 1,1997-05-22,1,['11.080.01'],ISO/TC 198,9599,,"[33953,31460,33955,33952]","['en','fr']",1,

33953,IS,,ISO 11137-2:2006,Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose,Stérilisation des produits de santé — Irradiation — Partie 2: Établissement de la dose stérilisante,2006-04-19,1,['11.080.01'],ISO/TC 198,9599,"[19156,28900,33832]",[51238],"['en','fr']",60,<p>ISO 11137-2:2006 specifies methods of determining the minimum dose needed to achieve a specified requirement for sterility and methods to substantiate the use of 25 kGy or 15 kGy as the sterilization dose to achieve a sterility assurance level (SAL) of 10^-6. It also specifies methods of dose auditing in order to demonstrate the continued effectiveness of the sterilizatio

53572,IS,Cor,ISO 11137-2:2006/Cor 1:2009,Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose — Technical Corrigendum 1,Stérilisation des produits de santé — Irradiation — Partie 2: Établissement de la dose stérilisante — Rectificatif technique 1,2009-02-10,1,['11.080.01'],ISO/TC 198,9599,,[51238],"['en','fr']",1,

51238,IS,,ISO 11137-2:2012,Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose,Stérilisation des produits de santé — Irradiation — Partie 2: Établissement de la dose stérilisante,2012-03-15,2,['11.080.01'],ISO/TC 198,9599,"[33953,53572]",[62442],"['en','fr']",70,"<p>ISO 11137-2:2011 specifies methods of determining the minimum dose needed to achieve a specified requirement for sterility and methods to substantiate the use of 25 kGy or 15 kGy as the sterilization dose to achieve a sterility assurance level, SAL, of 10^-6. ISO 11137-2:2011 also specifies methods of sterilization dose audit used to demonstrate the continued effectiveness of

33955,IS,,ISO 11137-3:2006,Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects,Stérilisation des produits de santé — Irradiation — Partie 3: Directives relatives aux aspects dosimétriques,2006-04-19,1,['11.080.01'],ISO/TC 198,9599,"[19156,28900,33832]",[63841],"['en','fr']",15,"<p>ISO 11137-3:2006 gives guidance on the requirements in ISO 11137 parts 1 and 2 relating to dosimetry. Dosimetry procedures related to the development, validation and routine control of a radiation sterilization process are described.</p>"

19157,IS,,ISO 11138-1:1994,Sterilization of health care products — Biological indicators — Part 1: General,Stérilisation des produits de santé — Indicateurs biologiques — Partie 1: Généralités,1994-10-06,1,['11.080.01'],ISO/TC 198,9599,,[33956],['en'],15,"<p>Specifies general production, labelling and performance requirements for the manufacture of biological indicators and suspensions intended for use in the validation and monitoring of sterilization cycles. Does not contain requirements for product directly inoculated with test organisms, or recovery procedures for such inoculated product.</p>"

33956,IS,,ISO 11138-1:2006,Sterilization of health care products — Biological indicators — Part 1: General requirements,Stérilisation des produits de santé — Indicateurs biologiques — Partie 1: Exigences générales,2006-06-26,2,['11.080.01'],ISO/TC 198,9599,[19157],[66442],"['en','fr']",38,"ISO 11138-1:2006 provides general requirements for production, labelling, test methods and performance characteristics of biological indicators, including inoculated carriers and suspensions, and their components, to be used in the validation and routine monitoring of sterilization processes.ISO 11138-1:2006 specifies basic and common requirements that are applicable to all subsequent parts of ISO 11138. R

20530,IS,,ISO 11138-2:1994,Sterilization of health care products — Biological indicators — Part 2: Biological indicators for ethylene oxide sterilization,Stérilisation des produits de santé — Indicateurs biologiques — Partie 2: Indicateurs biologiques pour stérilisation à l'oxyde d'éthylène,1994-10-06,1,['11.080.01'],ISO/TC 198,9599,,[33957],['en'],4,<p>Provides specific requirements for test organisms and biological indicators intended for use in assessing the performance of sterilizers employing pure ethylene oxide gas or admixtures of the gas with diluent gases at sterilizing temperatures within the range of 20 °C to 65 °C.</p>

33957,IS,,ISO 11138-2:2006,Sterilization of health care products — Biological indicators — Part 2: Biological indicators for ethylene oxide sterilization processes,Stérilisation des produits de santé — Indicateurs biologiques — Partie 2: Indicateurs biologiques pour la stérilisation à l'oxyde d'éthylène,2006-06-26,2,['11.080.01'],ISO/TC 198,9599,[20530],[66445],"['en','fr']",5,"<p>ISO 11138-2:2006 provides specific requirements for test organisms, suspensions, inoculated carriers, biological indicators and test methods intended for use in assessing the performance of sterilizers and sterilization processes employing ethylene oxide gas as the sterilizing agent, either as pure ethylene oxide g

20532,IS,,ISO 11138-3:1995,Sterilization of health care products — Biological indicators — Part 3: Biological indicators for moist heat sterilization,Stérilisation des produits de santé — Indicateurs biologiques — Partie 3: Indicateurs biologiques pour stérilisation à la vapeur d'eau,1995-09-21,1,['11.080.01'],ISO/TC 198,9599,,[33958],"['en','fr']",5,<p>Gives specific requirements for test organisms and biological indicators intended for use in assessing the performance of sterilizers employing moist heat as the sterilant.</p>

33958,IS,,ISO 11138-3:2006,Sterilization of health care products — Biological indicators — Part 3: Biological indicators for moist heat sterilization processes,Stérilisation des produits de santé — Indicateurs biologiques — Partie 3: Indicateurs biologiques pour la stérilisation à la chaleur humide,2006-06-26,2,['11.080.01'],ISO/TC 198,9599,[20532],[66446],"['en','fr']",8,"<p>ISO 11138-3:2006 provides specific requirements for test organisms, suspensions, inoculated carriers, biological indicators and test methods intended for use in assessing the performance of sterilization processes employing moist heat as the sterilizing agent.</p><p>Moist heat as the sterilizing agent is defined in ISO

33961,IS,,ISO 11138-4:2006,Sterilization of health care products — Biological indicators — Part 4: Biological indicators for dry heat sterilization processes,Stérilisation des produits de santé — Indicateurs biologiques — Partie 4: Indicateurs biologiques pour la stérilisation à la chaleur sèche,2006-06-26,1,['11.080.01'],ISO/TC 198,9599,,[66447],"['en','fr']",8,"<p>ISO 11138-4:2006 provides specific requirements for test organisms, suspensions, inoculated carriers, biological indicators, and test methods intended for use in assessing the performance of sterilization processes employing dry heat as the sterilizing agent at sterilizing temperatures within the range of 120 °C to 180 °C.</p>" 3

33960,IS,,ISO 11138-5:2006,Sterilization of health care products — Biological indicators — Part 5: Biological indicators for low-temperature steam and formaldehyde sterilization processes,Stérilisation des produits de santé — Indicateurs biologiques — Partie 5: Indicateurs biologiques pour la stérilisation à la vapeur d'eau et au formaldéhyde à basse température,2006-06-26,1,['11.080.01'],ISO/TC 198,9599,,[66448],"['en','fr']",7,"<p>ISO 11138-5:2006 provides specific requirements for test organisms, suspensions, inoculated carriers, biological indicators and test methods intended for use in assessing the performance of sterilization processes employing low-temperature steam and formaldehyde

5637,IS,,ISO 1114:1977,Cocoa beans — Cut test,Fèves de cacao — Épreuve à la coupe,1977-11-01,1,['67.140.30'],ISO/TC 34/SC 18,9599,,[68202],"['en','fr']",1,"<p>For the determination 300 beans shall be opened or cut lengthwise through the middle, so as to expose the maximum cut surface of cotyledones. Both halves of each bean shall be visually examined in full daylight or equivalent artificial light. Each defective type of bean shall be counted separately, and the result for each kind of defect shall be expressed as a percentage of the 300 beans examined.</p>"

19159,IS,,ISO 11140-1:1995,Sterilization of health care products — Chemical indicators — Part 1: General requirements,Stérilisation des produits de santé — Indicateurs chimiques — Partie 1: Prescriptions générales,1995-07-20,1,['11.080.01'],ISO/TC 198,9599,,[35046],"['en','fr']",7,<p>Specifies performance requirements for indicators that show exposure to sterilization processes by means of physical and/or chemical change of substances.</p>

28814,IS,Amd,ISO 11140-1:1995/Amd 1:1998,Sterilization of health care products — Chemical indicators — Part 1: General requirements — Amendment 1,Stérilisation des produits de santé — Indicateurs chimiques — Partie 1: Prescriptions générales — Amendement 1,1998-12-03,1,['11.080.01'],ISO/TC 198,9599,,[35046],['en'],1,

35046,IS,,ISO 11140-1:2005,Sterilization of health care products — Chemical indicators — Part 1: General requirements,Stérilisation des produits de santé — Indicateurs chimiques — Partie 1: Exigences générales,2005-07-20,2,['11.080.01'],ISO/TC 198,9599,"[19159,28814]",[55080],"['en','fr','ru']",27,"<p>ISO 11140-1:2005 specifies general requirements and test methods for indicators that show exposure to sterilization processes by means of physical and/or chemical change of substances, and which are used to monitor the attainment of one or more of the variables required for a sterilization process. They are not dependent for their action on the presence or absence of a living organism.</p><p>Th

21775,IS,,ISO 11140-2:1998,Sterilization of health care products — Chemical indicators — Part 2: Test equipment and methods,Stérilisation des produits de santé — Indicateurs chimiques — Partie 2: Appareillage et méthodes d'essai,1998-12-03,1,['11.080.01'],ISO/TC 198,9599,,[35047],['en'],7,

33750,IS,,ISO 11140-3:2000,Sterilization of health care products — Chemical indicators — Part 3: Class 2 indicators for steam penetration test sheets,Stérilisation des produits de santé — Indicateurs chimiques — Partie 3: Indicateur de classe 2 utilisé lors de l'essai de pénétration de la vapeur,2000-08-31,1,['11.080.01'],ISO/TC 198,9599,,"[40140,35048]",['en'],22,

33765,IS,,ISO 11140-4:2001,Sterilization of health care products — Chemical indicators — Part 4: Class 2 indicators for steam penetration test packs,Stérilisation des produits de santé — Indicateurs chimiques — Partie 4: Indicateurs de classe 2 pour paquets prépliés servant à l'essai de pénétration de la vapeur,2001-05-03,1,['11.080.01'],ISO/TC 198,9599,,[42129],['en'],33,

26035,IS,,ISO 11140-5:2000,Sterilization of health care products — Chemical indicators — Part 5: Class 2 indicators for air removal test sheets and packs,Stérilisation des produits de santé — Indicateurs chimiques — Partie 5: Indicateurs de classe 2 pour draps et paquets prépliés servant à l'essai d'enlèvement d'air,2000-11-02,1,['11.080.01'],ISO/TC 198,9599,,"[40141,35049]",['en'],13,

19162,IS,,ISO 11143:1999,Dental equipment — Amalgam separators,Matériel dentaire — Séparateurs d'amalgame,1999-12-02,1,['11.060.20'],ISO/TC 106/SC 6,9599,,[42288],"['en','fr']",23,

36957,IS,Cor,ISO 11143:1999/Cor 1:2002,Dental equipment — Amalgam separators — Technical Corrigendum 1,Matériel dentaire — Séparateurs d'amalgame — Rectificatif technique 1,2002-06-20,1,['11.060.20'],ISO/TC 106/SC 6,9599,,[42288],"['en','fr']",1,

19163,IS,,ISO 11144:1995,Dental equipment — Connections for supply and waste lines,Matériel dentaire — Raccordements pour lignes d'alimentation et d'évacuation,1995-04-27,1,"['13.030.40','11.060.20']",ISO/TC 106/SC 6,9599,,[59875],"['en','fr']",2,"<p>specifies requirements for the layout of the connections to the supply and waste lines for dental equipment, dental units, apparatus and devices, both as concerns the building plumbing and as mutually related to each other. Also lays down the relative positions, centres and minimum dimensions to accommodate the water, waste-water and suction supply lines, and adjacent spaces destined for electrical lines and compressed air lines for dental servi

2476,IS,,ISO 11145:1994,Optics and optical instruments — Lasers and laser-related equipment — Vocabulary and symbols,Optique et instruments d'optique — Lasers et équipements associés aux lasers — Vocabulaire et symboles,1994-11-24,1,"['31.260','01.040.31']",ISO/TC 172/SC 9,9599,,[28732],"['en','fr']",12,"<p>Defines basic terms, symbols and units of measurement for the field of laser technology in order to unify the terminology and to arrive at clear definitions and reproducible tests of beam parameters and laser-oriented product properties.</p>"

28732,IS,,ISO 11145:2001,Optics and optical instruments — Lasers and laser-related equipment — Vocabulary and symbols,Optique et instruments d'optique — Lasers et équipements associés aux lasers — Vocabulaire et symboles,2001-11-01,2,"['31.260','01.040.31','01.080.40']",ISO/TC 172/SC 9,9599,[2476],[43006],"['en','fr']",22,

43006,IS,,ISO 11145:2006,Optics and photonics — Lasers and laser-related equipment — Vocabulary and symbols,Optique et photonique — Lasers et équipements associés aux lasers — Vocabulaire et symboles,2006-05-10,3,"['31.260','01.040.31','01.080.40']",ISO/TC 172/SC 9,9599,"[40765,28732]",[65247],"['en','fr']",29,"<p>ISO 11145:2006 defines basic terms, symbols and units of measurement for the field of laser technology in order to unify the terminology and to arrive at clear definitions and reproducible tests of beam parameters and laser-oriented product properties.</p>"

65247,IS,,ISO 11145:2016,Optics and photonics — Lasers and laser-related equipment — Vocabulary and symbols,Optique et photonique — Lasers et équipements associés aux lasers — Vocabulaire et symboles,2016-02-25,4,"['31.260','01.040.31','01.080.40']",ISO/TC 172/SC 9,9599,[43006],[72944],"['en','fr']",20,"<p>ISO 11145:2016 defines basic terms, symbols, and units of measurement for the field of laser technology in order to unify the terminology and to arrive at clear definitions and reproducible tests of beam parameters and laser-oriented product properties.</p><p>NOTE The laser hierarchical vocabulary laid down in this International Standard differs from that given in IEC 60825?1. ISO

72944,IS,,ISO 11145:2018,Optics and photonics — Lasers and laser-related equipment — Vocabulary and symbols,Optique et photonique — Lasers et équipements associés aux lasers — Vocabulaire et symboles,2018-11-02,5,"['31.260','01.040.31','01.080.40']",ISO/TC 172/SC 9,9599,[65247],[87910],"['en','fr']",21,"<p>This document defines basic terms, symbols, and units of measurement for the field of laser technology in order to unify the terminology and to arrive at clear definitions and reproducible tests of beam parameters and laser-oriented product properties.</p><p>NOTE The laser hierarchical vocabulary laid down in this document differs from that given in IEC 60825?1. ISO and IEC have disc

33625,IS,,ISO 11146-1:2005,"Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles and beam propagation ratios — Part 1: Stigmatic and simple astigmatic beams","Lasers et équipements associés aux lasers — Méthodes d'essai des largeurs du faisceau, angles de divergence et facteurs de limite de diffraction — Partie 1: Faisceaux stigmatiques et astigmatiques simples",2005-01-05,1,['31.260'],ISO/TC 172/SC 9,9599,[2519],"[50332,77769]","['en','fr','ru']",16,"<p>ISO 11146-1:2005 specifies methods for measuring beam widths (diameter), divergence angles and beam propagation ratios of laser beams.</p><p>ISO 11146-1:2005 is only applicable for stigmatic and simple a

2519,IS,,ISO 11146:1999,"Lasers and laser-related equipment — Test methods for laser beam parameters — Beam widths, divergence angle and beam propagation factor","Lasers et équipements associés aux lasers — Méthodes d'essai des paramètres des faisceaux laser — Largeurs du faisceau, angle de divergence et facteur de propagation du faisceau",1999-05-20,1,['31.260'],ISO/TC 172/SC 9,9599,,"[31689,33625]","['en','fr']",26,

33626,IS,,ISO 11146-2:2005,"Lasers and laser-related equipment — Test methods for laser beam widths, divergence angles and beam propagation ratios — Part 2: General astigmatic beams","Lasers et équipements associés aux lasers — Méthodes d'essai des largeurs du faisceau, angles de divergence et facteurs de limite de diffraction — Partie 2: Faisceaux astigmatiques généraux",2005-02-18,1,['31.260'],ISO/TC 172/SC 9,9599,,"[50333,77770]","['en','fr','ru']",15,"<p>ISO 11146-2:2005 specifies methods for measuring beam widths (diameter), divergence angles and beam propagation ratios of laser beams. ISO 11146-2:2005 is applicable to general astigmatic beams or unknown types of beams. For stigmatic an

50132,IS,,ISO 11148-3:2010,Hand-held non-electric power tools — Safety requirements — Part 3: Drills and tappers,Machines portatives à moteur non électrique — Exigences de sécurité — Partie 3: Perceuses et taraudeuses,2010-09-23,1,['25.140.10'],ISO/TC 118/SC 3,9599,,[61679],"['en','fr']",27,"<p>ISO 11148-3:2010 applies to hand-held non-electric power tools (hereafter referred to as “drills and tappers”) intended for rotary drilling of holes in all kinds of material, e.g. wood, metal, concrete, plastics, etc., or for tapping and cleaning threads in metal and plastics. The drills and tappers can be powered by compressed air, hydraulic fluid or internal combustion engines and are intended for u

50133,IS,,ISO 11148-4:2010,Hand-held non-electric power tools — Safety requirements — Part 4: Non-rotary percussive power tools,Machines portatives à moteur non électrique — Exigences de sécurité — Partie 4: Machines portatives non rotatives à percussion,2010-09-23,1,['25.140.10'],ISO/TC 118/SC 3,9599,,[61680],"['en','fr']",29,"<p>ISO 11148-4:2010 applies to hand-held non-electric power tools (hereafter referred to as “non-rotary percussive power tools”) intended for chipping, riveting, breaking of concrete and asphalt, ramming, etc. The non-rotary percussive power tool can be powered by compressed air, hydraulic fluid or internal combustion engines and intended for use by one operator and s

50135,IS,,ISO 11148-6:2010,Hand-held non-electric power tools — Safety requirements — Part 6: Assembly power tools for threaded fasteners,Machines portatives à moteur non électrique — Exigences de sécurité — Partie 6: Machines d'assemblage pour éléments de fixation filetés,2010-09-23,1,['25.140.10'],ISO/TC 118/SC 3,9599,,[61681],"['en','fr']",32,"<p>ISO 11148-6:2010 applies to hand-held non-electric power tools (hereafter referred to as “assembly power tools for threaded fasteners”) intended for tightening or installing of threaded fasteners. The assembly power tools for threaded fasteners can be powered by compressed air, hydraulic fluid or internal combustion engines and are intended for u

2543,IS,,ISO 11151-1:2000,"Lasers and laser-related equipment — Standard optical components — Part 1: Components for the UV, visible and near-infrared spectral ranges","Lasers et équipements associés aux lasers — Composants optiques standards — Partie 1: Composants pour les plages spectrales UV, visible et proche de l'infrarouge",2000-06-22,1,['31.260'],ISO/TC 172/SC 9,9599,,[61833],"['en','fr']",12,

22246,IS,,ISO 11151-2:2000,Lasers and laser-related equipment — Standard optical components — Part 2: Components for the infrared spectral range,Lasers et équipements associés aux lasers — Composants optiques standards — Partie 2: Composants pour la plage spectrale infrarouge,2000-06-22,1,['31.260'],ISO/TC 172/SC 9,9599,,[61834],"['en','fr']",12,

19164,IS,,ISO 11154-1:1995,Road vehicles — Roof load carriers — Part 1: Roof bars,Véhicules routiers — Dispositifs porte-charges de toit — Partie 1: Barres porte-charges,1995-10-12,1,['43.040.60'],ISO/TC 22,9599,,[43941],"['en','fr']",14,"<p>Specifies the minimum safety requirements for roof bars intended for mounting on or above the roofs of passenger cars or light commercial vehicles with a maximum authorized total mass up to 3,5 t.</p>"

26213,IS,,ISO 11154-4:2004,Road vehicles — Roof load carriers — Part 4: Magnetic fixing devices,Véhicules routiers — Dispositifs porte-charges de toit — Partie 4: Dispositifs à fixation magnétique,2004-10-12,1,['43.040.60'],ISO/TC 22,9599,,[43941],"['en','fr']",26,"<p>ISO11154-4:2004 establishes technical specifications for the magnetic fixing devices of roof load carriers and specifies the minimum safety requirements, and test methods, for such devices, thus offering the occupants of those vehicles on which the carriers are mounted, as well as other road users and pedestrians, a minimum level of safety when the devices are used in accordance with the manufacturer's instructions. It is appli

19167,IS,,ISO 11157:1999,Road vehicles — Brake lining assemblies — Inertia dynamometer test method,Véhicules routiers — Ensembles de garniture de frein — Méthode d'essai sur banc dynamométrique à inertie,1999-10-21,1,['43.040.40'],ISO/TC 22,9599,,[36952],"['en','fr']",16,

19168,IS,,ISO 11158:1997,"Lubricants, industrial oils and related products (class L) — Family H (hydraulic systems) — Specifications for categories HH, HL, HM, HR, HV and HG","Lubrifiants, huiles industrielles et produits connexes (classe L) — Famille H (systèmes hydrauliques) — Spécifications des catégories HH, HL, HM, HR, HV et HG",1997-12-11,1,['75.120'],ISO/TC 28/SC 4,9599,,[40038],"['en','fr']",12,

40038,IS,,ISO 11158:2009,"Lubricants, industrial oils and related products (class L) — Family H (hydraulic systems) — Specifications for categories HH, HL, HM, HV and HG","Lubrifiants, huiles industrielles et produits connexes (classe L) — Famille H (systèmes hydrauliques) — Spécifications des catégories HH, HL, HM, HV et HG",2009-08-31,2,['75.120'],ISO/TC 28/SC 4,9599,[19168],"[81871,84812]","['en','fr']",15,"<p>ISO 11158:2009 specifies the minimum requirements for new mineral oil hydraulic fluids and is intended for hydraulic systems, particularly for hydrostatic hydraulic fluid power application. The purpose of ISO 11158:2009 is for the guidance of suppliers and end users of mineral oil h

5639,IS,,ISO 1116:1975,"Microcopying — 16 mm and 35 mm microfilms, spools and reels",Microcopie — Microfilms de 16 mm et de 35 mm et leurs bobines d'approvisionnement et de lecture,1975-11-01,1,['37.080'],ISO/TC 171/SC 2,9599,,[5640],"['en','fr']",6,

19171,IS,,ISO 11161:1994,Industrial automation systems — Safety of integrated manufacturing systems — Basic requirements,Systèmes d'automatisation industrielle — Sécurité des systèmes de fabrication intégrés — Prescriptions fondamentales,1994-03-24,1,['25.040.01'],ISO/TC 184,9599,,[35996],"['en','fr']",25,"<p>Specifies the safety requirements for integrated manufacturing systems that incorporate two or more industrial machines interconnected with and operated by a controller(s) capable of being reprogrammed for the manufacturing of discrete parts or assemblies. Describes the requirements and recommendations for the safe installation, programming, operation, maintenance, or repair of such sy

5641,IS,,ISO 1117:1975,Bonded abrasive products — Grinding-wheel dimensions (Part 2),Produits abrasifs agglomérés — Dimensions des meules (Deuxième partie),1975-05-01,1,['25.100.70'],ISO/TC 29/SC 5,9599,,"[2724,4713,4707,21897,4714,21898,4709,21899,4710,20536,2736,21900,4711,21632,4712,2715]","['en','fr']",21,

2000,IS,,ISO 11170:1995,Hydraulic fluid power — Filter elements — Procedure for verifying performance characteristics,Transmissions hydrauliques — Éléments filtrants — Procédure d'homologation,1995-11-09,1,['23.100.60'],ISO/TC 131/SC 6,9599,,[33394],"['en','fr']",4,"<p>Defines a procedure for verification of the performance characteristics of filter elements. It can be used to check their hydraulic, mechanical and separation characteristics.</p>"

33394,IS,,ISO 11170:2003,Hydraulic fluid power — Filter elements — Sequence of tests for verifying performance characteristics,Transmissions hydrauliques — Éléments filtrants — Ordre des essais pour la vérification des caractéristiques de performance,2003-08-21,2,['23.100.60'],ISO/TC 131/SC 6,9599,[2000],[55198],"['en','fr']",6,"<p>ISO 11170:2003 defines a sequence of tests for verifying filter elements. It can be used to check their hydraulic, mechanical and separation characteristics.</p><p>ISO 11170:2003 is not intended to qualify a filter for a particular duty or replicate conditions of service. This can only be done by a specific test protocol developed for the purpose, including actual

1919,IS,,ISO 11171:1999,Hydraulic fluid power — Calibration of automatic particle counters for liquids,Transmissions hydrauliques — Étalonnage des compteurs automatiques de particules en suspension dans les liquides,1999-12-09,1,['23.100.60'],ISO/TC 131/SC 6,9599,[10308],[46573],"['en','fr']",58,

35965,IS,Cor,ISO 11171:1999/Cor 1:2001,Hydraulic fluid power — Calibration of automatic particle counters for liquids — Technical Corrigendum 1,Transmissions hydrauliques — Étalonnage des compteurs automatiques de particules en suspension dans les liquides — Rectificatif technique 1,2001-09-27,1,['23.100.60'],ISO/TC 131/SC 6,9599,,[46573],"['en','fr']",1,

46573,IS,,ISO 11171:2010,Hydraulic fluid power — Calibration of automatic particle counters for liquids,Transmissions hydrauliques — Étalonnage des compteurs automatiques de particules en suspension dans les liquides,2010-10-25,2,['23.100.60'],ISO/TC 131/SC 6,9599,"[1919,35965]",[70291],"['en','fr']",50,"<p>ISO 11171:2010 specifies procedures for: a) primary particle-sizing calibration, sensor resolution and counting performance of automatic particle counters (APCs) for liquids capable of analysing bottle samples; b) secondary particle-sizing calibration using suspensions verified with a primary calibrated APC; c) establishing acceptable operation and performance limits; d) verifying particl

70291,IS,,ISO 11171:2016,Hydraulic fluid power — Calibration of automatic particle counters for liquids,Transmissions hydrauliques — Étalonnage des compteurs automatiques de particules en suspension dans les liquides,2016-10-05,3,['23.100.60'],ISO/TC 131/SC 6,9599,[46573],[72619],"['en','fr']",51,"<p>ISO 11171:2016 specifies procedures for the following:</p><p>a) primary particle-sizing calibration, sensor resolution and counting performance of automatic particle counters (APCs) for liquids capable of analysing bottle samples;</p><p>b) secondary particle-sizing calibration using suspensions verified with a primary calibrated APC;</p><p>c) establishing acceptable operation and perfor

72619,IS,,ISO 11171:2020,Hydraulic fluid power — Calibration of automatic particle counters for liquids,Transmissions hydrauliques — Étalonnage des compteurs automatiques de particules en suspension dans les liquides,2020-11-19,4,['23.100.60'],ISO/TC 131/SC 6,9599,[70291],[82850],"['en','fr']",52,"<p>This document specifies procedures for the following:</p><p>a) primary particle-sizing calibration for particle sizes 1 µm(c) and larger, sensor resolution and counting performance of liquid automatic particle counters that are capable of analysing bottle samples;</p><p>b) secondary particle-sizing calibration using suspensions verified with a primary calibrated APC;</p><p>c) establishing

19181,IS,,ISO 11174:1996,Workplace air — Determination of particulate cadmium and cadmium compounds — Flame and electrothermal atomic absorption spectrometric method,Air des lieux de travail — Dosage du cadmium particulaire et des composés particulaires du cadmium — Méthode par spectrométrie d'absorption atomique dans la flamme et méthode par spectrométrie d'absorption atomique avec atomisation électrothermique,1996-04-25,1,['13.040.30'],ISO/TC 146/SC 2,9599,,[82199],"['en','fr']",15,"<p>Specifies methods for the determination of the mass concentration of particulate cadmium and cadmium compounds in workplace air by electrothermal atomic absorption spectrometric method (ETAAS) applicable to

62853,IS,,ISO 11177:2016,Vitreous and porcelain enamels — Inside and outside enamelled valves and pressure pipe fittings for untreated and potable water supply — Quality requirements and testing,Émaux vitrifiés — Robinetterie émaillée à l'intérieur et à l'extérieur et raccords de tuyauterie pour conduites forcées destinées à l'alimentation en eau non traitée et en eau potable — Exigences de qualité et essais,2016-02-10,1,"['91.140.60','25.220.50']",ISO/TC 107,9599,,[74516],"['en','fr']",6,<p>ISO 11177:2016 specifies the requirements for product quality and product testing of enamelled valves and pressure pipe fittings for untreated and potable water supply. It is not applicable for chemical

5643,IS,,ISO 1119:1975,Series of conical tapers and taper angles,Série d'angles de cônes et de conicités,1975-06-01,1,['17.040.01'],ISO/TC 213,9599,,[28068],"['en','fr']",3,

28068,IS,,ISO 1119:1998,Geometrical Product Specifications (GPS) — Series of conical tapers and taper angles,Spécification géométrique des produits (GPS) — Série d'angles de cônes et de conicités,1998-09-03,2,['17.040.01'],ISO/TC 213,9599,[5643],[54835],"['en','fr']",6,

19191,IS,,ISO 11191:1997,Gas cylinders — 25E taper thread for connection of valves to gas cylinders — Inspection gauges,Bouteilles à gaz — Filetage conique 25E pour le raccordement des robinets sur les bouteilles à gaz — Calibres de vérification,1997-03-13,1,['23.020.35'],ISO/TC 58/SC 2,9599,,[50449],"['en','fr']",12,

33621,IS,,ISO 11193-1:2002,Single-use medical examination gloves — Part 1: Specification for gloves made from rubber latex or rubber solution,"Gants en caoutchouc pour examen, non réutilisables — Partie 1: Spécifications pour gants fabriqués à partir de latex de caoutchouc ou d'une solution de caoutchouc",2002-10-25,1,"['11.140','83.140.99']",ISO/TC 45/SC 4,9599,[19193],[50766],['en'],9,"<p>ISO 11193-1 specifies requirements for packaged sterile, or bulked non-sterile, rubber gloves intended for use in medical examinations and diagnostic or therapeutic procedures to protect the patient and the user from cross-contamination. It also covers rubber gloves intended for use in handling contaminat

43713,IS,Amd,ISO 11193-1:2002/Amd 1:2007,Single-use medical examination gloves — Part 1: Specification for gloves made from rubber latex or rubber solution — Amendment 1,"Gants en caoutchouc pour examen, non réutilisables — Partie 1: Spécifications pour gants fabriqués à partir de latex de caoutchouc ou d'une solution de caoutchouc — Amendement 1",2007-05-15,1,"['11.140','83.140.99']",ISO/TC 45/SC 4,9599,,[50766],['en'],2,