Withdrawn and superseded ISO standards — page 166 of 246

39357,IS,,ISO 8029:2007,"Plastics hose — General-purpose collapsible water hose, textile-reinforced — Specification",Tuyaux plastiques — Tuyaux d'eau écrasables d'usage général renforcés textiles — Spécifications,2007-06-04,2,['23.040.70'],ISO/TC 45/SC 1,9599,[15039],[59522],"['en','fr']",12,"<p>ISO 8029:2007 specifies the requirements for four types of textile-reinforced thermoplastics collapsible water hoses for general applications for use in the temperature range of -10 °C to +55 °C.</p><p>Such hoses are classified into four types, as follows:</p><ul><li>low pressure, designed for a maximum working pressure of up to 4,0 bar at 23 °C and up to 2,0 bar at 55 °C;</li><li>medium pressure, fo

5148,IS,,ISO 803:1976,Aluminium oxide primarily used for the production of aluminium — Determination of loss of mass at 300 degrees C (conventional moisture),Oxyde d'aluminium principalement utilisé pour la production de l'aluminium — Détermination de la perte de masse à 300 degrés C (humidité conventionnelle),1976-09-01,1,['71.100.10'],ISO/TC 226,9599,,"[36360,36721]","['en','fr']",2,

15040,IS,,ISO 8030:1987,Rubber and plastics hoses for underground mining — Method of test for flammability,Tuyaux en caoutchouc et en plastique pour les exploitations minières souterraines — Méthode d'essai d'inflammabilité,1987-12-03,1,"['83.140','73.100.30','13.220.40']",ISO/TC 45/SC 1,9599,,[21873],"['en','fr']",4,

21873,IS,,ISO 8030:1995,Rubber and plastics hoses — Method of test for flammability,Tuyaux en caoutchouc et en plastique — Méthode d'essai d'inflammabilité,1995-12-27,2,"['13.220.40','23.040.70']",ISO/TC 45/SC 1,9599,[15040],[62580],"['en','fr']",4,"<p>Specifies a method for assessing the flammability of hoses, except for hoses intended for use with petroleum fuels for combustion engines. Restricted to hoses of sizes up to and including 50 mm nominal bore. Replaces the first edition.</p>"

15041,IS,,ISO 8031:1987,Rubber and plastics hoses and hose assemblies — Determination of electrical resistance,Tuyaux et flexibles en caoutchouc et en plastique — Détermination de la résistance électrique,1987-12-03,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[21874],"['en','fr']",4,

21874,IS,,ISO 8031:1993,Rubber and plastics hoses and hose assemblies — Determination of electrical resistance,Tuyaux et flexibles en caoutchouc et en plastique — Détermination de la résistance électrique,1993-12-23,2,['23.040.70'],ISO/TC 45/SC 1,9599,[15041],[41795],"['en','fr']",4,"<p>Specifies methods for electrical tests on rubber and plastic hoses and hose assemblies to determine the resistance of conductive, antistatic and non-conductive hoses, the electrical continuity between fittings, and the electrical discontinuity.</p>"

41795,IS,,ISO 8031:2009,Rubber and plastics hoses and hose assemblies — Determination of electrical resistance and conductivity,Tuyaux et flexibles en caoutchouc et en plastique — Détermination de la résistance et de la conductivité électriques,2009-10-05,3,['23.040.70'],ISO/TC 45/SC 1,9599,[21874],[80489],"['en','fr','ru']",15,"<p>ISO 8031:2009 specifies electrical test methods for rubber and plastics hoses, tubing and hose assemblies to determine the resistance of conductive, antistatic and non-conductive hoses and the electrical continuity or discontinuity between metal end fittings.</p>"

15042,IS,,ISO 8032:1987,Rubber and plastics hose assemblies — Flexing combined with hydraulic impulse test (Half omega test),Flexibles hydrauliques en caoutchouc et en plastique — Essai de flexion combiné avec des impulsions de pression (Essai demi-oméga),1987-11-05,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[21875],['en'],3,

15043,IS,,ISO 8033:1985,Rubber and plastics hose — Determination of adhesion between components,Tuyaux en caoutchouc et en plastique — Détermination de l'adhérence entre éléments,1985-07-11,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[15044],"['en','fr']",8,

15044,IS,,ISO 8033:1991,Rubber and plastics hose — Determination of adhesion between components,Tuyaux en caoutchouc et en plastique — Détermination de l'adhérence entre éléments,1991-12-05,2,['23.040.70'],ISO/TC 45/SC 1,9599,[15043],[39356],"['en','fr']",9,"<p>Covers all bore sizes and the following construction types: woven textile fabric, braided yarns and wires, spirally yarns and wires, knitted yarns, circular woven yarns, textile cord fabric, hoses containing a supporting helix. This second edition cancels and replaces the first edition (1985).</p>"

39356,IS,,ISO 8033:2006,Rubber and plastics hoses — Determination of adhesion between components,Tuyaux en caoutchouc et en plastique — Détermination de l'adhérence entre éléments,2006-07-06,3,['23.040.70'],ISO/TC 45/SC 1,9599,[15044],[68055],"['en','fr']",11,"<p>Adequate adhesion between the various components of a hose is essential if it is to perform satisfactorily in service. ISO 8033:2006 specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection) and between lining and inner lamination (thin layer of ma

15047,IS,,ISO 8036-1:1986,Optics and optical instruments — Microscopes — Part 1: Immersion oil for general use in light microscopy,Optique et instruments d'optique — Microscopes — Partie 1: Huile d'immersion pour usage général en microscopie optique,1986-09-18,1,['37.020'],ISO/TC 172/SC 5,9599,,[26918],['en'],2,

26918,IS,,ISO 8036-1:1998,Optics and optical instruments — Microscopes — Part 1: Immersion oil for general use in light microscopy,Optique et instruments d'optique — Microscopes — Partie 1: Huile d'immersion pour usage général en microscopie optique,1998-03-05,2,['37.020'],ISO/TC 172/SC 5,9599,[15047],[39399],"['en','fr']",3,

39399,IS,,ISO 8036:2006,Optics and photonics — Microscopes — Immersion liquids for light microscopy,Optique et photonique — Microscopes — Liquides d'immersion pour microscopie optique,2006-05-16,1,['37.020'],ISO/TC 172/SC 5,9599,[26918],[67551],['en'],5,"<p>ISO 8036:2006 describes the characteristics of immersion liquids used in microscopy. It classifies immersion liquids according to their field of application and specifies requirements and test methods for each type.</p><p>The standard further specifies a system of designation for immersion liquids, the information to be included on container labels and the information to be supplied in technical data sheets.</p>"

45976,IS,,ISO 80369-1:2010,Small-bore connectors for liquids and gases in healthcare applications — Part 1: General requirements,Raccords de petite taille pour liquides et gaz utilisés dans le domaine de la santé — Partie 1: Exigences générales,2010-12-08,1,"['11.040.10','11.040.20']",ISO/TC 210,9599,,[64419],"['en','fr']",17,"<p>ISO 80369-1:2010 specifies general requirements for small-bore connectors, which convey liquids or gases in healthcare applications. These small-bore connectors are used in medical devices or accessories intended for use with a patient. </p><p>ISO 80369-1:2010 also specifies the healthcare fields in which these small-bore connectors are intended to be used.</p><p>T

64419,IS,,ISO 80369-1:2018,Small-bore connectors for liquids and gases in healthcare applications — Part 1: General requirements,Raccords de petite taille pour liquides et gaz utilisés dans le domaine de la santé — Partie 1: Exigences générales,2018-11-05,2,"['11.040.10','11.040.20']",ISO/TC 210,9599,[45976],[82071],"['en','fr']",31,"<p>This document specifies general requirements for small-bore connectors, which convey liquids or gases in healthcare applications. These small-bore connectors are used in medical devices or accessories intended for use with a patient.</p><p>This document also specifies the healthcare fields in which these small-bore connectors are intended to be used.</p><p>Th

63837,IS,,ISO 80369-20:2015,Small-bore connectors for liquids and gases in healthcare applications — Part 20: Common test methods,Raccords de petite taille pour liquides et gaz utilisés dans le domaine de la santé — Partie 20: Méthodes d'essai communes,2015-05-11,1,['11.040.25'],ISO/TC 210,9599,,[82712],"['en','fr']",29,<p>ISO 80369-20:2015 specifies the test methods to evaluate the performance requirements for small-bore connectors specified in the ISO 80369‑ series.</p>

50734,IS,,ISO 80369-6:2016,Small bore connectors for liquids and gases in healthcare applications — Part 6: Connectors for neuraxial applications,Raccords de petite taille pour liquides et gaz utilisés dans le domaine de la santé — Partie 6: Raccords destinés à des applications en contact avec le système nerveux (neuraxiales),2016-03-14,1,['11.040.25'],ISO/TC 210,9599,,[85462],"['en','fr']",45,"<p>ISO 80369-6:2016 specifies requirements for small-bore connectors intended to be used for connections in neuraxial applications. Neuraxial applications involve the use of medical devices intended to administer medications to neuraxial sites, wound infiltration anaesthesia delivery, and other region

58011,IS,,ISO 80369-7:2016,Small-bore connectors for liquids and gases in healthcare applications — Part 7: Connectors for intravascular or hypodermic applications,Raccords de petite taille pour liquides et gaz utilisés dans le domaine de la santé — Partie 7: Raccords à 6 % (Luer) destinés aux applications intravasculaires ou hypodermiques,2016-10-14,1,['11.040.25'],ISO/TC 210,9599,"[29540,4693]",[79173],"['en','fr']",43,"<p>ISO 80369-7:2016 specifies dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections in intravascular applications or hypodermic connections in hypodermic applications of medical devices and accesso

26919,IS,,ISO 8038-1:1997,Optics and optical instruments — Microscopes — Screw threads for objectives and related nosepieces — Part 1: Screw thread type RMS (4/5 in x 1/36 in),Optique et instruments d'optique — Microscopes — Filetages de fixation des objectifs et des porte-objectifs correspondants — Partie 1: Filetage de type RMS (4/5 in x 1/36 in),1997-12-11,1,['37.020'],ISO/TC 172/SC 5,9599,[15050],[53790],"['en','fr']",3,

15050,IS,,ISO 8038:1985,Optics and optical instruments — Microscopes — Screw thread for objectives,Optique et instruments d'optique — Microscopes — Filetage de fixation des objectifs,1985-11-14,1,['37.020'],ISO/TC 172/SC 5,9599,,[26919],"['en','fr']",2,

33192,IS,,ISO 8038-2:2001,"Optics and optical instruments — Screw threads for microscope objectives and related nosepieces — Part 2: Screw thread type M25 X 0,75 mm","Optique et instruments d'optique — Filetages de fixation des objectifs pour microscopes et des porte-objectifs correspondants — Partie 2: Filetage de type M25 X 0,75 mm",2001-01-25,1,['37.020'],ISO/TC 172/SC 5,9599,,[53790],"['en','fr']",2,

53790,IS,,ISO 8038:2011,Microscopes — Screw threads for objectives and related nosepieces,Microscopes — Filetages de fixation des objectifs et des porte-objectifs correspondants,2011-04-07,2,['37.020'],ISO/TC 172/SC 5,9599,"[26919,33192]",[62859],['en'],5,<p>ISO 8038:2011 specifies the dimensions of screw thread types for connecting a microscope objective to the nosepiece. </p>

62859,IS,,ISO 8038:2013,Microscopes — Screw threads for objectives and related nosepieces,Microscopes — Filetages de fixation des objectifs et des porte-objectifs correspondants,2013-10-23,3,['37.020'],ISO/TC 172/SC 5,9599,[53790],[70798],['en'],5,<p>ISO 8038:2013 specifies the dimensions of screw thread types for connecting a microscope objective to the nosepiece.</p>

15051,IS,,ISO 8039:1997,Optics and optical instruments — Microscopes — Magnification,Optique et instruments d'optique — Microscopes — Grossissement,1997-11-13,1,['37.020'],ISO/TC 172/SC 5,9599,,[50987],"['en','fr']",6,

50987,IS,,ISO 8039:2012,"Microscopes — Values, tolerances and symbols for magnification","Microscopes — Valeurs, tolérances et symboles de grossissement",2012-09-28,2,['37.020'],ISO/TC 172/SC 5,9599,[15051],[66260],['en'],3,"<p>ISO 8039:2012 specifies a series of values, tolerances and symbols for the magnification of imaging components of light microscopes and defines a number of imaging components and magnifying systems to which they apply.</p>"

15052,IS,,ISO 8040:1986,Optics and optical instruments — Microscopes — Connecting dimensions of tube slides and tube slots,Optique et instruments d'optique — Microscopes — Cotes de liaison entre les tirettes et leurs logements,1986-09-18,1,['37.020'],ISO/TC 172/SC 5,9599,,[29651],"['en','fr']",2,

15053,IS,,ISO 8041:1990,Human response to vibration — Measuring instrumentation,Réponse des individus aux vibrations — Appareillage de mesure,1990-07-12,1,['13.160'],ISO/TC 108,9599,,[30145],"['en','fr']",24,

27055,IS,Amd,ISO 8041:1990/Amd 1:1999,Human response to vibration — Measuring instrumentation — Amendment 1,Réponse des individus aux vibrations — Appareillage de mesure — Amendement 1,1999-11-04,1,['13.160'],ISO/TC 108,9599,,"[30145,40602]","['en','fr']",23,

22320,IS,Cor,ISO 8041:1990/Cor 1:1993,Human response to vibration — Measuring instrumentation — Technical Corrigendum 1,Réponse des individus aux vibrations — Appareillage de mesure — Rectificatif technique 1,1993-06-24,1,['13.160'],ISO/TC 108,9599,,"[30145,40602]","['en','fr']",3,"<p>Amends Foreword, subclauses 3.3.2, 4.3.2, 9.2, D.1, D.2, replaces figure D.1.</p>"

30145,IS,,ISO 8041:2005,Human response to vibration — Measuring instrumentation,Réponse des individus aux vibrations — Appareillage de mesure,2005-04-06,2,['13.160'],ISO/TC 108,9599,"[15053,22320,27055]",[70648],"['en','fr']",91,"<p>ISO 8041:2005 specifies the performance specifications and tolerance limits for instruments designed to measure vibration values, for the purpose of assessing human response to vibration. It includes requirements for pattern evaluation, periodic verification and <i>in-situ</i> checks, and the specification of vibration calibrators for <i>in-situ</i> checks.</p><p>Vibration instruments specified in ISO 8041:2005 can be single instruments, combinations of instrumen

50575,IS,Cor,ISO 8041:2005/Cor 1:2007,Human response to vibration — Measuring instrumentation — Technical Corrigendum 1,Réponse des individus aux vibrations — Appareillage de mesure — Rectificatif technique 1,2007-11-05,2,['13.160'],ISO/TC 108,9599,,[70648],"['en','fr']",2,

15056,IS,,ISO 8044:1986,Corrosion of metals and alloys — Terms and definitions,Corrosion des métaux et alliages — Termes et définitions,1986-12-22,1,"['01.040.77','77.060']",ISO/TC 156,9599,,[15057],"['en','fr','ru']",,

15057,IS,,ISO 8044:1989,Corrosion of metals and alloys — Vocabulary,Corrosion des métaux et alliages — Vocabulaire,1989-12-14,2,"['01.040.77','77.060']",ISO/TC 156,9599,[15056],[26132],"['en','fr','ru']",17,

15059,IS,Amd,ISO 8044:1989/Amd 1:1993,Corrosion of metals and alloys — Vocabulary — Amendment 1,Corrosion des métaux et alliages — Vocabulaire — Amendement 1,1993-05-13,2,"['01.040.77','77.060']",ISO/TC 156,9599,,[26132],"['en','fr']",5,

26132,IS,,ISO 8044:1999,Corrosion of metals and alloys — Basic terms and definitions,Corrosion des métaux et alliages — Termes principaux et définitions,1999-12-16,3,"['01.040.77','77.060']",ISO/TC 156,9599,"[15059,15057]",[66233],"['en','fr','ru']",65,

66233,IS,,ISO 8044:2015,Corrosion of metals and alloys — Basic terms and definitions,Corrosion des métaux et alliages — Termes principaux et définitions,2015-08-25,4,"['01.040.77','77.060']",ISO/TC 156,9599,[26132],[71134],"['en','fr']",24,"<p>ISO 8044:2015 defines terms relating to corrosion that are widely used in modern science and technology. In addition, some definitions are supplemented with short explanations.</p><p>NOTE 1 Throughout the document IUPAC rules for electrode potential signs are applied. The term 'metal' is also used to include alloys and other metallic materials.</p><p>NOTE 2 Terms and definitions related to inorganic surface treatment of metals are given in

71134,IS,,ISO 8044:2020,Corrosion of metals and alloys — Vocabulary,Corrosion des métaux et alliages — Vocabulaire,2020-02-07,5,"['01.040.77','77.060']",ISO/TC 156,9599,[66233],[83222],"['en','fr']",29,"<p>This document defines terms relating to corrosion that are widely used in modern science and technology. In addition, some definitions are supplemented with short explanations.</p><p>NOTE 1 Throughout the document, IUPAC rules for electrode potential signs are applied. The term 'metal' is also used to include alloys and other metallic materials.</p><p>NOTE 2 Terms and definitions related to the inorganic surface treatment of metals are given in ISO 2080.</p>"

15063,IS,,ISO 8048:1984,"Technical drawings — Construction drawings — Representation of views, sections and cuts","Dessins techniques — Dessins de construction — Représentation des vues, des sections et des coupes",1984-12-01,1,['01.100.30'],ISO/TC 10/SC 8,9599,,"[41426,63795]","['en','fr']",5,"<p>General rules are layed down for marking, designation, placing and orientation and the position of text in relation to figures. For all general rules reference is made to ISO 128. As regards relative positions of views, the method using reference arrows according to ISO 128 is applied.</p>"

15064,IS,,ISO 8049:1988,Ferronickel shot — Sampling for analysis,Ferro-nickel en grenailles — Échantillonnage pour analyse,1988-12-15,1,['77.100'],ISO/TC 155,9599,,[65091],"['en','fr']",19,<p>Applies to ferronickel lots in the form of shot as specified in ISO 6501 in those cases where lots are constituted either heat by heat or by taking from blendes stock. The purpose is to determine the contents of the various elements either from slugs by physical analysis methods or from chips by dry methods or chemical analysis.</p>

15066,IS,,ISO 8051:1989,Long shank taps with nominal diameters from M3 to M10 — Taps with reinforced shank and recess,"Tarauds à machine, à queue longue, de diamètre nominal M3 à M10 — Tarauds à queue pleine, à gorge",1989-10-19,1,['25.100.50'],ISO/TC 29,9599,,[28556],"['en','fr']",2,

28556,IS,,ISO 8051:1999,Long shank taps with nominal diameters from M3 to M10 — Full-diameter shank taps with recess,"Tarauds à machine, à queue longue, de diamètre nominal M3 à M10 — Tarauds à queue pleine, à gorge",1999-03-04,2,['25.100.50'],ISO/TC 29/SC 9,9599,[15066],[60700],"['en','fr']",4,

15067,IS,,ISO 8052:1984,Road vehicles — Mopeds — D.C. flasher units,Véhicules routiers — Cyclomoteurs — Centrales clignotantes en courant continu,1984-10-01,1,['43.140'],ISO/TC 22,9599,,[15068],['en'],5,

15069,IS,,ISO 8053:1986,Rubber and latex — Determination of copper content — Photometric method,Caoutchouc et latex — Dosage du cuivre — Méthode photométrique Caoutchouc et latex — Dosage du cuivre — Méthode photométrique,1986-11-20,1,"['83.060','83.040.10']",ISO/TC 45,9599,"[6270,5982]",[20154],"['en','fr']",4,

15070,IS,,ISO 8054:1988,"Rubber, compounded or vulcanized — Determination of sulfide sulfur content — Iodometric method",Caoutchouc vulcanisé ou non vulcanisé — Dosage du soufre sous forme de sulfure — Méthode iodométrique,1988-11-24,1,['83.060'],ISO/TC 45,9599,,[24255],"['en','fr']",5,

15076,IS,,ISO 8058:1985,Air cargo equipment — Air mode insulated containers — Thermal efficiency requirements,Équipement pour le fret aérien — Conteneurs isothermes pour transport aérien — Caractéristiques de rendement thermique,1985-05-16,1,['55.180.30'],ISO/TC 20/SC 9,9599,,[1522],"['en','fr']",7,

5151,IS,,ISO 806:1976,Aluminium oxide primarily used for the production of aluminium — Determination of loss of mass at 1 000 degrees C and 1 200 degrees C,Oxyde d'aluminium principalement utilisé pour la production de l'aluminium — Détermination de la perte de masse à 1 000 degrés C et à 1 200 degrés C,1976-09-01,1,['71.100.10'],ISO/TC 226,9599,,[36360],"['en','fr']",3,"<p>The temperatures are arbitrarily selected and specified because there is no specific calcination temperature. There is no criterion for the state of calcination. Therefore, ignition of two test portions taken from the same sample and previously dried in a muffle furnace for 2 h. Calculation by difference in mass. Replaces

51141,IS,,ISO 80601-2-12:2011,Medical electrical equipment — Part 2-12: Particular requirements for basic safety and essential performance of critical care ventilators,Appareils électromédicaux — Partie 2-12: Exigences particulières relatives à la sécurité de base et aux performances essentielles des ventilateurs pulmonaires pour utilisation en soins intensifs,2011-04-07,1,['11.040.10'],ISO/TC 121/SC 3,9599,[23914],[72069],"['en','fr']",78,"<p>ISO 80601-2-12:2011 applies to the basic safety and essential performance of a ventilator in combination with its accessories, hereafter referred to as me equipment: </p><ul><li>intended to be attended by a professional operator for those patients who

60254,IS,Cor,ISO 80601-2-12:2011/Cor 1:2011,Medical electrical equipment — Part 2-12: Particular requirements for basic safety and essential performance of critical care ventilators — Technical Corrigendum 1,Appareils électromédicaux — Partie 2-12: Exigences particulières relatives à la sécurité de base et aux performances essentielles des ventilateurs pulmonaires pour utilisation en soins intensifs — Rectificatif technique 1,2011-10-11,1,['11.040.10'],ISO/TC 121/SC 3,9599,,[72069],"['en','fr']",4,

72069,IS,,ISO 80601-2-12:2020,Medical electrical equipment — Part 2-12: Particular requirements for basic safety and essential performance of critical care ventilators,Appareils électromédicaux — Partie 2-12: Exigences particulières relatives à la sécurité de base et aux performances essentielles des ventilateurs pulmonaires pour utilisation en soins intensifs,2020-02-25,2,['11.040.10'],ISO/TC 121/SC 3,9599,"[60254,51141]",[82707],"['en','fr']",138,"<p>This document applies to the <i>basic safety</i> and <i>essential performance</i> of a <i>ventilator</i> in combination with its <i>accessories</i>, hereafter referred to as <i>ME equipment:</i> </p><ul><li> intended for use in an environme

51285,IS,,ISO 80601-2-13:2011,Medical electrical equipment — Part 2-13: Particular requirements for basic safety and essential performance of an anaesthetic workstation,Appareils électromédicaux — Partie 2-13: Exigences particulières de sécurité de base et de performances essentielles pour les postes de travail d'anesthésie,2011-08-08,1,['11.040.10'],ISO/TC 121/SC 1,9599,"[56123,35202,43235,35203,39199,31657,41114]",[76679],"['en','fr']",99,"<p>ISO/IEC 80601-2-13:2011 is applicable to the basic safety and essential performance of an anaesthetic workstation for administering inhalational anaesthesia whilst continuously attended by a professional operator. </p><p>ISO/IEC 80601-2-13:2011 specif

61685,IS,Amd,ISO 80601-2-13:2011/Amd 1:2015,Medical electrical equipment — Part 2-13: Particular requirements for basic safety and essential performance of an anaesthetic workstation — Amendment 1,Appareils électromédicaux — Partie 2-13: Exigences particulières de sécurité de base et de performances essentielles pour les postes de travail d'anesthésie — Amendement 1,2015-03-06,1,['11.040.10'],ISO/TC 121/SC 1,9599,,[76679],"['en','fr']",11,

71537,IS,Amd,ISO 80601-2-13:2011/Amd 2:2018,Medical electrical equipment — Part 2-13: Particular requirements for basic safety and essential performance of an anaesthetic workstation — Amendment 2,Appareils électromédicaux — Partie 2-13: Exigences particulières de sécurité de base et de performances essentielles pour les postes de travail d'anesthésie — Amendement 2,2018-07-19,1,['11.040.10'],ISO/TC 121/SC 1,9599,,[76679],"['en','fr']",2,

52211,IS,,ISO 80601-2-55:2011,Medical electrical equipment — Part 2-55: Particular requirements for the basic safety and essential performance of respiratory gas monitors,Appareils électromédicaux — Partie 2-55: Exigences particulières relatives à la sécurité de base et aux performances essentielles des moniteurs de gaz respiratoires,2011-12-15,1,['11.040.10'],ISO/TC 121/SC 1,9599,"[34637,42637]",[67241],"['en','fr']",52,"<p>ISO 80601-2-55:2011 specifies particular requirements for the basic safety and essential performance of a respiratory gas monitor (RGM) intended for continuous operation for use with a patient.</p><p>ISO 80601-2-55:2011 specifies requirements for:</p><ul><li> anaes

44106,IS,,ISO 80601-2-56:2009,Medical electrical equipment — Part 2-56: Particular requirements for basic safety and essential performance of clinical thermometers for body temperature measurement,Appareils électromédicaux — Partie 2-56: Exigences particulières relatives à la sécurité fondamentale et aux performances essentielles des thermomètres médicaux pour mesurer la température de corps,2009-09-30,1,['11.040.55'],ISO/TC 121/SC 3,9599,,[67348],"['en','fr','ru']",46,"<p>ISO 80601-2-56:2009 applies to the basic safety and essential performance of a clinical thermometer in combination with its accessories, referred to as ME equipment. ISO 80601-2-56:2009 specifies the general and technical

51847,IS,,ISO 80601-2-61:2011,Medical electrical equipment — Part 2-61: Particular requirements for basic safety and essential performance of pulse oximeter equipment,Appareils électromédicaux — Partie 2-61: Exigences particulières pour la sécurité de base et les performances essentielles pour les oxymètres de pouls,2011-03-16,1,['11.040.10'],ISO/TC 121/SC 3,9599,[33780],[67963],"['en','fr','ru']",83,"<p>ISO 80601-2-61:2011 applies to the basic safety and essential performance of pulse oximeter equipment intended for use on humans, hereafter referred to as ME equipment. This includes any part necessary for normal use, including the pulse oximeter monitor, pulse oximeter probe, and probe cabl

67963,IS,,ISO 80601-2-61:2017,Medical electrical equipment — Part 2-61: Particular requirements for basic safety and essential performance of pulse oximeter equipment,Appareils électromédicaux — Partie 2-61: Exigences particulières pour la sécurité de base et les performances essentielles pour les oxymètres de pouls,2017-12-15,2,['11.040.10'],ISO/TC 121/SC 3,9599,[51847],[84595],"['en','fr']",90,"<p>ISO 80601-2-61:2017 applies to the basic safety and essential performance of pulse oximeter equipment intended for use on humans, hereafter referred to as me equipment. This includes any part necessary for normal use, including the pulse oximeter monitor, pulse oximeter probe, and probe cable ext

46478,IS,,ISO 80601-2-67:2014,Medical electrical equipment — Part 2-67: Particular requirements for basic safety and essential performance of oxygen-conserving equipment,Appareils électromédicaux — Partie 2-67: Exigences particulières pour la sécurité de base et les performances essentielles dee économiseurs d'oxygène,2014-05-14,1,['11.040.10'],ISO/TC 121/SC 3,9599,[38872],[75945],"['en','fr']",43,"<p>ISO 80601-2-67:2014 is applicable to the basic safety and essential performance of oxygen conserving equipment, hereafter referred to as me equipment, in combination with its accessories intended to conserve supplemental oxygen by delivering gas intermittently and synchronized with the patient'

75945,IS,,ISO 80601-2-67:2020,Medical electrical equipment — Part 2-67: Particular requirements for basic safety and essential performance of oxygen-conserving equipment,Appareils électromédicaux — Partie 2-67: Exigences particulières pour la sécurité de base et les performances essentielles des économiseurs d'oxygène,2020-10-30,2,['11.040.10'],ISO/TC 121/SC 3,9599,[46478],[87163],"['en','fr']",57,"<p>This document is applicable to the <i>basic safety</i> and <i>essential performance</i> of oxygen <i>conserving equipment</i>, hereafter referred to as <i>ME equipment,</i> in combination with its <i>accessories </i>intended to conserve supplemental oxygen by delivering gas intermittently and s

59978,IS,,ISO 80601-2-69:2014,Medical electrical equipment — Part 2-69: Particular requirements for basic safety and essential performance of oxygen concentrator equipment,Appareils électromédicaux — Partie 2-69: Exigences particulières pour la sécurité de base et les performances essentielles des dispositifs concentrateurs d'oxygène,2014-07-15,1,['11.040.10'],ISO/TC 121/SC 3,9599,"[22625,60989]",[75946],"['en','fr']",42,"<p>ISO 80601-2-69:2014 specifies requirements for the basic safety and essential performance of an oxygen concentrator in combination with its accessories, hereafter referred to as ME equipment, intended to increase the oxygen concentration of gas intended to be delivered t

75946,IS,,ISO 80601-2-69:2020,Medical electrical equipment — Part 2-69: Particular requirements for the basic safety and essential performance of oxygen concentrator equipment,Appareils électromédicaux — Partie 2-69: Exigences particulières pour la sécurité de base et les performances essentielles des dispositifs concentrateurs d'oxygène,2020-11-06,2,['11.040.10'],ISO/TC 121/SC 3,9599,[59978],[87164],"['en','fr']",62,"<p>This document specifies requirements for the <i>basic safety</i> and <i>essential performance</i> of an <i>oxygen</i> <i>concentrator</i> in combination with its <i>accessories</i>, hereafter referred to as <i>ME equipment, </i>intended to increase the oxygen concentration o

60049,IS,,ISO 80601-2-70:2015,Medical electrical equipment — Part 2-70: Particular requirements for basic safety and essential performance of sleep apnoea breathing therapy equipment,Appareils électromédicaux — Partie 2-70: Exigences particulières pour la sécurité de base et les performances essentielles du matériel de traitement respiratoire de l'apnée du sommeil,2015-01-12,1,['11.040.10'],ISO/TC 121/SC 3,9599,[41615],[75947],"['en','fr']",46,"<p>ISO 80601-2-70:2015 is applicable to the basic safety and essential performance of sleep apnoea breathing therapy equipment, hereafter referred to as me equipment, intended to alleviate the symptoms of patients who suffer from obstructive sleep apn

75947,IS,,ISO 80601-2-70:2020,Medical electrical equipment — Part 2-70: Particular requirements for the basic safety and essential performance of sleep apnoea breathing therapy equipment,Appareils électromédicaux — Partie 2-70: Exigences particulières pour la sécurité de base et les performances essentielles de l'équipement de thérapie respiratoire pour l'apnée du sommeil,2020-11-17,2,['11.040.10'],ISO/TC 121/SC 3,9599,[60049],[87160],"['en','fr']",68,"<p>This document is applicable to the <i>basic safety</i> and <i>essential performance</i> of <i>sleep apnoea breathing therapy equipment</i>, hereafter referred to as <i>ME equipment, </i>intended to alleviate the symptoms of <i>patients</i>

61389,IS,,ISO 80601-2-72:2015,Medical electrical equipment — Part 2-72: Particular requirements for basic safety and essential performance of home healthcare environment ventilators for ventilator-dependent patients,Appareils électromédicaux — Partie 2-72: Exigences particulières pour la sécurité de base et les performances essentielles des ventilateurs utilisés dans l'environnement des soins à domicile pour les patients ventilo-dépendants,2015-09-01,1,['11.040.10'],ISO/TC 121/SC 3,9599,[35973],[83464],"['en','fr']",87,"<p>ISO 80601-2-72:2015 applies to the basic safety and essential performance of a ventilator in combination with its accessories, hereafter referred to as me equipment:</p><u

65008,IS,,ISO 80601-2-74:2017,Medical electrical equipment — Part 2-74: Particular requirements for basic safety and essential performance of respiratory humidifying equipment,Appareils électromédicaux — Partie 2-74: Exigences particulières pour la sécurité de base et les performances essentielles des équipements d'humidification respiratoire,2017-05-18,1,['11.040.10'],ISO/TC 121/SC 3,9599,[38527],[81613],"['en','fr']",88,"<p>ISO 80601-2-74:2017 applies to the basic safety and essential performance of a humidifier, also hereafter referred to as me equipment, in combination with its accessories, the combination also hereafter referred to as me system.</p><p>ISO 80601-2-74:2017 is also applica

81613,IS,,ISO 80601-2-74:2021,Medical electrical equipment — Part 2-74: Particular requirements for basic safety and essential performance of respiratory humidifying equipment,Appareils électromédicaux — Partie 2-74: Exigences particulières pour la sécurité de base et les performances essentielles des équipements d'humidification respiratoire,2021-07-13,2,['11.040.10'],ISO/TC 121/SC 3,9599,[65008],[87155],"['en','fr']",99,"<p>This document applies to the <em>basic safety</em> and <em>essential performance</em> of a <em>humidifier</em>, also hereafter referred to as <em>ME equipment,</em> in combination with its <em>accessories</em>, the combination also hereafter referred to as <em>ME system

68843,IS,,ISO 80601-2-79:2018,Medical electrical equipment — Part 2-79: Particular requirements for basic safety and essential performance of ventilatory support equipment for ventilatory impairment,Appareils électromédicaux — Partie 2-79: Exigences particulières pour la sécurité de base et les performances essentielles des équipements d'assistance ventilatoire en cas de trouble ventilatoire,2018-07-18,1,['11.040.10'],ISO/TC 121/SC 3,9599,[35974],[83465],"['en','fr']",76,"<p>This document applies to the basic safety and essential performance of ventilatory support equipment, as defined in 201.3.205, for ventilatory impairment, as defined in 201.3.202, hereafter also referred to as me equipme

68844,IS,,ISO 80601-2-80:2018,Medical electrical equipment — Part 2-80: Particular requirements for basic safety and essential performance of ventilatory support equipment for ventilatory insufficiency,Appareils électromédicaux — Partie 2-80: Exigences particulières pour la sécurité de base et les performances essentielles des équipements d'assistance ventilatoire en cas d'insuffisance ventilatoire,2018-07-18,1,['11.040.10'],ISO/TC 121/SC 3,9599,[35974],[83466],"['en','fr']",85,"<p>This document applies to the basic safety and essential performance of ventilatory support equipment, as defined in 201.3.205, for ventilatory insufficiency, as defined in 201.3.204, hereafter also referred to as

72441,IS,,ISO 80601-2-84:2020,Medical electrical equipment — Part 2-84: Particular requirements for the basic safety and essential performance of ventilators for the emergency medical services environment,Appareils électromédicaux — Partie 2-84: Exigences particulières relatives à la sécurité de base et aux performances essentielles des ventilateurs utilisés dans l'environnement des services médicaux d'urgence,2020-07-21,1,['11.040.10'],ISO/TC 121/SC 3,9599,[21436],[83438],"['en','fr']",110,"<p>This document applies to the <i>basic safety</i> and <i>essential performance</i> of an <i>EMS</i> <i>ventilator</i> in combination with its <i>accessories</i>, hereafter also referred to as <i>ME equ

80858,IS,,ISO 80601-2-90:2021,Medical electrical equipment — Part 2-90: Particular requirements for basic safety and essential performance of respiratory high-flow therapy equipment,Appareils électromédicaux — Partie 2-90: Exigences particulières pour la sécurité de base et les performances essentielles des équipements de thérapie respiratoire à haut débit,2021-08-30,1,['11.040.10'],ISO/TC 121/SC 3,9599,,[87151],"['en','fr']",89,"<p>This document applies to the <em>basic safety</em> and <em>essential performance</em> of <em>respiratory high-flow therapy equipment,</em> as defined in 201.3.220, hereafter also referred to as <em>ME equipment </em>or<em> ME system,</em> in combination with its

15080,IS,,ISO 8061:1984,Alpine skis — Ski bindings — Methods for the selection of release torque values,Skis alpins — Fixations — Méthodes de sélection des valeurs du couple de déclenchement,1984-03-01,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[15081],"['en','fr']",4,

15081,IS,,ISO 8061:1991,Alpine ski-bindings — Selection of release torque values,Fixations de skis alpins — Sélection des valeurs du couple de déclenchement,1991-08-15,2,['97.220.20'],ISO/TC 83/SC 4,9599,[15080],[36307],"['en','fr']",4,<p>Gives information necessary to determine the release torques. The methods apply to torque-measuring binding test machines. This second edition cancels and replaces the first edition (1984). Annex A is for information only.</p>

36307,IS,,ISO 8061:2004,Alpine ski-bindings — Selection of release torque values,Fixations de skis alpins — Sélection des valeurs du couple de déclenchement,2004-03-30,3,['97.220.20'],ISO/TC 83/SC 4,9599,[15081],[68518],"['en','fr']",6,"<p>ISO 8061:2004 specifies methods for the selection of the release torques for alpine ski-bindings in current use, and gives information necessary to determine the release torques.</p><p>It applies to torque-measuring binding-test machines.</p><p>It may be inappropriate for non-mechanical bindings or bindings used with boots which reach more than half-way up the lower leg.</p>"

42732,IS,Amd,ISO 8061:2004/Amd 1:2006,Alpine ski-bindings — Selection of release torque values — Amendment 1,Fixations de skis alpins — Sélection des valeurs du couple de déclenchement — Amendement 1,2006-10-17,3,['97.220.20'],ISO/TC 83/SC 4,9599,,[68518],"['en','fr']",2,

68518,IS,,ISO 8061:2015,Alpine ski-bindings — Selection of release torque values,Fixations de skis alpins — Sélection des valeurs du couple de déclenchement,2015-12-03,4,['97.220.20'],ISO/TC 83/SC 4,9599,"[36307,42732]",[75609],"['en','fr']",5,"<p>ISO 8061:2015 specifies methods for the selection of the release torques for alpine ski-bindings. It gives information necessary to determine the release torques; these are to be recommended for use by ski-binding manufacturers in their instructions for installation and use, and by ski shops for the adjustment of already mounted ski-bindings.</p><p>It applies to alpine ski-bindings in current use.</p><p>It might be inappropriate for non-mechanical

15082,IS,,ISO 8062:1984,Castings — System of dimensional tolerances,Pièces moulées — Système de tolérances dimensionnelles,1984-10-01,1,['17.040.10'],ISO/TC 213,9599,,[15083],"['en','fr']",5,

15083,IS,,ISO 8062:1994,Castings — System of dimensional tolerances and machining allowances,Pièces moulées — Système de tolérances dimensionnelles et surépaisseurs d'usinage,1994-03-24,2,['17.040.10'],ISO/TC 213,9599,[15082],"[40496,40494,40495]","['en','fr']",13,<p>Applies to cast metals and their alloys produced by various casting manufacturing processes. Is applicable both to general tolerances and/or required machining allowances given on a drawing and to individual tolerances and/or required machining allowances which are shown immediately following a specific dimension. The system specified applies when the foundry provides the pattern or die equipment or accepts responsibility for pr

40495,IS,,ISO 8062-3:2007,Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings,Spécification géométrique des produits (GPS) — Tolérances dimensionnelles et géométriques des pièces moulées — Partie 3: Tolérances dimensionnelles et géométriques générales et surépaisseurs d'usinage pour les pièces moulées,2007-05-31,1,['17.040.10'],ISO/TC 213,9599,[15083],[77952],"['en','fr']",30,"<p>ISO 8062-3:2007 specifies general dimensional and geometrical tolerances, as well as machining allowance grades, for castings as delivered to the purchaser in accordance with

52988,IS,Cor,ISO 8062-3:2007/Cor 1:2009,Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 3: General dimensional and geometrical tolerances and machining allowances for castings — Technical Corrigendum 1,Spécification géométrique des produits (GPS) — Tolérances dimensionnelles et géométriques des pièces moulées — Partie 3: Tolérances dimensionnelles et géométriques générales et surépaisseurs d'usinage pour les pièces moulées — Rectificatif technique 1,2009-01-14,1,['17.040.10'],ISO/TC 213,9599,,[77952],"['en','fr']",2,

60774,IS,,ISO 8062-4:2017,Geometrical product specifications (GPS) — Dimensional and geometrical tolerances for moulded parts — Part 4: General tolerances for castings using profile tolerancing in a general datum system,Spécification géométrique des produits (GPS) — Tolérances dimensionnelles et géométriques pour les pièces moulées — Partie 4: Tolérances générales pour les pièces moulées par tolérancement de profil dans un système général de références spécifiées,2017-07-31,1,['17.040.10'],ISO/TC 213,9599,,[77154],['en'],25,"<p>ISO 8062-4:2017 specifies general geometrical tolerances using surface profile tolerances related to a general datum system that remains on the final part. It also sp

15088,IS,,ISO 8067:1989,Flexible cellular polymeric materials — Determination of tear strength,Matériaux polymères alvéolaires souples — Détermination de la résistance au déchirement,1989-10-05,1,['83.100'],ISO/TC 45/SC 4,9599,,[42716],"['en','fr']",3,<p>Specifies a method for the determination of the tear strength of flexibility cellular polymeric materials having a thickness of more than 24.0 mm. The procedure described produces a value which may be regarded as a measure of the tear resistance of foam under the conditions of this particular test.</p>

42716,IS,,ISO 8067:2008,Flexible cellular polymeric materials — Determination of tear strength,Matériaux polymères alvéolaires souples — Détermination de la résistance au déchirement,2008-11-17,2,['83.100'],ISO/TC 45/SC 4,9599,[15088],[72855],"['en','fr']",8,"<p>ISO 8067:2008 specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:</p><ul><li>method A, using a trouser test piece;</li><li>method B, using an angle test piece without a nick.</li></ul>"

15089,IS,,ISO 8068:1987,Petroleum products and lubricants — Petroleum lubricating oils for turbines (categories ISO-L-TSA and ISO-L-TGA) — Specifications,Produits pétroliers et lubrifiants — Huiles lubrifiantes de pétrole pour turbines (catégories ISO-L-TSA et ISO-L-TGA) — Spécifications,1987-06-18,1,['75.100'],ISO/TC 28/SC 4,9599,,[40037],"['en','fr']",4,"<p>Specifies required characteristics of mineral oils as delivered that are primarily intended for use as lubricants and control fluids for steam turbine systems requiring oils of category TSA and that may be used for gas turbines using oils of category TGA and for water turbines. These oils are not intended for service when extreme pressu

40037,IS,,ISO 8068:2006,"Lubricants, industrial oils and related products (class L) — Family T (Turbines) — Specification for lubricating oils for turbines","Lubrifiants, huiles industrielles et produits connexes (classe L) — Famille T (Turbines) — Spécifications pour les huiles lubrifiantes pour turbines",2006-09-22,2,['75.100'],ISO/TC 28/SC 4,9599,[15089],[85619],"['en','fr','ru']",16,"<p>ISO 8068:2006 specifies the minimum requirements for turbine lubricants, as delivered. It specifies the requirements for a wide variety of turbines for power generation, including steam turbines, gas turbines, combined-cycle turbines with a common lubrication system and hydraulic (water driven) turbines.

75354,IS,Amd,ISO 8068:2006/Amd 1:2019,"Lubricants, industrial oils and related products (class L) — Family T (Turbines) — Specification for lubricating oils for turbines — Amendment 1: Filterability tests according to ISO 13357-1 and ISO 13357-2 — Requirements related to the stage of the test method","Lubrifiants, huiles industrielles et produits connexes (classe L) — Famille T (Turbines) — Spécifications pour les huiles lubrifiantes pour turbines — Amendement 1: Essais de filtrabilité selon les normes ISO 13357-1 et ISO 13357-2 — Exigences relatives au stade de la méthode d'essai",2019-03-04,2,['75.100'],ISO/TC 28/SC 4,9599,,[85619],"['en','fr']",5,

15090,IS,,ISO 8069:1986,Dried milk — Determination of lactic acid and lactates content — Enzymatic method,Lait sec — Determination de la teneur en acide lactique et en lactates — Méthode enzymatique,1986-06-05,1,['67.100.10'],ISO/TC 34/SC 5,9599,[8846],[36686],"['en','fr']",4,<p>Applies to all types of dried milk. The sampling shall be made according to ISO 707. The method specified is mainly based on `Methods of enzymatic food analysis: UV-method for the determination of L-lactic acid and D-lactic acid in foodstuffs' by Boehringer Mannheim GmbH.</p>

15091,IS,,ISO 8070:1987,Dried milk — Determination of sodium and potassium contents — Flame emission spectrometric method,Lait sec — Détermination des teneurs en sodium et potassium — Méthode par spectrométrie d'émission de flamme,1987-03-12,1,['67.100.10'],ISO/TC 34/SC 5,9599,,"[44079,38485]","['en','fr']",3,<p>Covers all types of dried milk. The sampling shall be made as specified in ISO 707. A table gives information as to preparating and composition of 7 different sodium and potassium reference solutions.</p>

15093,IS,,ISO 8072:1986,Information processing systems — Open Systems Interconnection — Transport service definition,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Service de transport en mode connexion,1986-06-26,1,['35.100.40'],ISO/IEC JTC 1/SC 6,9599,,[21414],"['en','fr']",16,

15095,IS,Cor,ISO 8072:1986/Cor 1:1991,Information processing systems — Open Systems Interconnection — Transport service definition — Technical Corrigendum 1,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Service de transport en mode connexion — Rectificatif technique 1,1991-07-18,1,['35.100.40'],ISO/IEC JTC 1/SC 6,9599,,[21414],['en'],1,

15096,IS,,ISO 8073:1986,Information processing systems — Open Systems Interconnection — Connection oriented transport protocol specification,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Protocole de transport en mode connexion,1986-07-24,1,['35.100.70'],ISO/IEC JTC 1/SC 6,9599,,[15097],['fr'],,

15107,IS,,ISO 8074:1985,Aerospace — Surface treatment of austenitic stainless steel parts,Aéronautique et espace — Traitement de surface des éléments en acier inoxydable austénitique,1985-08-01,1,['49.040'],ISO/TC 20/SC 18,9599,,[84866],"['en','fr']",5,<p>Gives the requirements to be met. Provides practical methods for removing contaminants and for obtaining suitable corrosion resistance. The surface treatments required during manufacture are mandatory for all surfaces. The final surface treatments are mandatory except when a surface coating is specified.</p>

15108,IS,,ISO 8075:1985,Aerospace — Surface treatment of hardenable stainless steel parts,Aéronautique et espace — Traitement de surface des éléments en acier inoxydable à durcissement structural,1985-08-01,1,['49.040'],ISO/TC 20/SC 18,9599,,[84867],"['en','fr']",6,"<p>Specifies the requirements for parts made from martensitic, precipitation hardening and maraging stainless steels. Provides practical methods for removing contaminants and for obtaining suitable corrosion resistance for aerospace applications. The final surface treatments are mandatory except when a surface coating is specified.</p>"

15111,IS,,ISO 8078:1984,"Aerospace process — Anodic treatment of aluminium alloys — Sulfuric acid process, undyed coating",Procédés de traitement dans l'industrie aérospatiale — Traitement anodique des alliages d'aluminium — Traitement à l'acide sulfurique pour revêtement non teinté,1984-10-01,1,['49.040'],ISO/TC 20/SC 18,9599,,[84864],"['en','fr']",3,"<p>Specifies requirements for producing and testing a coating on aluminium alloys. The anodizing process is applied in the manufacture of aerospace products to improve paint adhesion and resistance to corrosion. Gives technical requirements, quality assurance provisions, packaging and delivery.</p>"

15112,IS,,ISO 8079:1984,"Aerospace process — Anodic treatment of aluminium alloys — Sulfuric acid process, dyed coating",Procédés de traitement dans l'industrie aérospatiale — Traitement anodique des alliages d'aluminium — Traitement à l'acide sulfurique pour revêtement coloré,1984-10-01,1,['49.040'],ISO/TC 20/SC 18,9599,,[84865],"['en','fr']",3,"<p>Includes requirements for producing and testing a coating on aluminium alloys where the coating is not required to withstand prolonged exposure to weathering and direct sunlight. The anodizing process is applied in the manufacture of aerospace products to improve resistance to corrosion, produce coloured surfaces for aesthetic reasons or to colou

15113,IS,,ISO 8080:1985,Aerospace — Anodic treatment of titanium and titanium alloys — Sulfuric acid process,Aéronautique et espace — Traitement anodique du titane et de ses alliages — Traitement à l'acide sulfurique,1985-05-09,1,['49.040'],ISO/TC 20/SC 18,9599,,[75445],"['en','fr']",2,"<p>Specifies the requirements for producing and testing. The coating is used with solid film lubricants for protection of titanium fasteners against galling, for limited protection of less noble metals against galvanic corrosion when in contact with titanium or for other approved uses. Gives information on technical requirements, quality assurance provisions, packaging and delivery.</p>"

15114,IS,,ISO 8081:1985,Aerospace process — Chemical conversion coating for aluminium alloys — General purpose,Procédés de traitement dans l'industrie aérospatiale — Revêtement par conversion chimique des alliages d'aluminium — Utilisation courante,1985-01-17,1,['49.040'],ISO/TC 20/SC 18,9599,,[75446],"['en','fr']",4,"<p>Describes the requirements for producing and testing. The coating specified is used in the manufacture of aerospace products in order to improve paint adhesion and resistance to corrosion. This process may also be used for touch-up of anodic coatings. Gives information on technical requirements, quality assurance provisions, packaging and delivery.</p>"

15115,IS,,ISO 8082:1994,Self-propelled machinery for forestry — Roll-over protective structures — Laboratory tests and performance requirements,Machines forestières automotrices — Structures de protection au retournement — Essais de laboratoire et critères de performance,1994-02-03,1,['65.060.80'],ISO/TC 23/SC 15,9599,,[31059],"['en','fr']",12,"<p>Establishes a consistent, reproducible means of evaluating force-deflection characteristics of roll-over protective structures under static loading, and prescribes performance requirements for a representative specimen under such loading. Applies to mobile and self-propelled specially designed machinery for forestry as defined in ISO 6814.</p>" 151

31059,IS,,ISO 8082:2003,Self-propelled machinery for forestry — Roll-over protective structures — Laboratory tests and performance requirements,Machines forestières automotrices — Structures de protection au retournement — Essais de laboratoire et exigences de performance,2003-03-25,2,['65.060.80'],ISO/TC 23/SC 15,9599,[15115],[53412],"['en','fr']",15,"<p>ISO 8082:2003 establishes a consistent, reproducible means of evaluating the force-deflection characteristics of roll-over protective structures (ROPS) on self-propelled forestry machines under static loading, and prescribes performance requirements for a representative specimen under such loading. It is applicable to forwarders, skidders,

15116,IS,,ISO 8083:1989,Machinery for forestry — Falling-object protective structures — Laboratory tests and performance requirements,Matériel forestier — Structures de protection contre les chutes d'objets — Essais de laboratoire et critères de performance,1989-12-21,1,['65.060.80'],ISO/TC 23/SC 15,9599,,[39099],"['en','fr']",6,"<p>Establishes a consistent, repeatable means of evaluating characteristics of protective structures under loading. Applies to mobile or self-propelled specially-designed machines as defined in ISO 6814. Some figures illustrate the drop test objekt and drop test impact points. Annex A gives a standard test report; annex B contains additional information for originat

15117,IS,,ISO 8084:1993,Machinery for forestry — Operator protective structures — Laboratory tests and performance requirements,Machines forestières — Structures de protection de l'opérateur — Essais de laboratoire et critères de performance,1993-12-23,1,['65.060.80'],ISO/TC 23/SC 15,9599,,[31626],"['en','fr']",3,"<p>Establishes a consistent repeatable means of evaluating characteristics of an operator protective structure under loading, and prescribes performance requirements for this structure under such loading in a representative test. Applies to mobile forestry machines and equipment defined in ISO 6814.</p>"