Withdrawn and superseded ISO standards — page 162 of 246

14603,IS,,ISO 7752-3:1993,Cranes — Controls — Layout and characteristics — Part 3: Tower cranes,Appareils de levage à charge suspendue — Organes de service — Disposition et caractéristiques — Partie 3: Grues à tour,1993-12-23,1,['53.020.20'],ISO/TC 96/SC 7,9599,,[46494],"['en','fr']",3,"<p>Specifies the particular requirements for controls for tower cranes as defined in ISO 4306-1 and ISO 4306-3 and the arrangement of basic controls used for positioning loads. Applies to the controls of tower cranes for building and general construction work that can be dismantled, permanently erected tower cranes, hammerhead cranes, dockside and shipbuilders' tower cranes. Does not apply to the controls of

46494,IS,,ISO 7752-3:2010,Cranes — Control layout and characteristics — Part 3: Tower cranes,Appareils de levage à charge suspendue — Disposition et caractéristiques des commandes — Partie 3: Grues à tour,2010-05-11,2,['53.020.20'],ISO/TC 96/SC 7,9599,[14603],[62876],"['en','fr']",3,"<p>ISO 7752-3:2010 specifies the particular requirements for the controls of tower cranes as defined in ISO 4306-3 and the arrangement of those basic controls used for positioning loads. It is intended to be used in conjunction with ISO 7752-1, which gives general principles and requirements for the controls of all types of cranes.</p>"

14605,IS,,ISO 7752-5:1985,Lifting appliances — Controls — Layout and characteristics — Part 5: Overhead travelling cranes and portal bridge cranes,Appareils de levage — Organes de service — Disposition et caractéristiques — Partie 5: Ponts roulants et ponts portiques,1985-12-19,1,['53.020.20'],ISO/TC 96/SC 9,9599,,[76824],"['en','fr']",3,"<p>Establishes the arrangement, requirements and direction of movement of the basic controls for travelling, traversing, slewing, cab driving, lifting, hoisting and lowering operations for these cranes as defined in ISO 4306-1.</p>"

14606,IS,,ISO 7753:1987,Nuclear energy — Performance and testing requirements for criticality detection and alarm systems,Énergie nucléaire — Prescriptions relatives aux caractéristiques techniques et aux méthodes d'essai des systèmes de détection et d'alarme de criticité,1987-08-13,1,['27.120.10'],ISO/TC 85/SC 5,9599,,[81438],"['en','fr']",9,"<p>Is applicable to all operations with plutonium, uranium 233, uranium enriched in the 235 isotope, and other fissionable materials. Does not require separate additional instrumentation when the operating instrumentation of the facilities meets its requirements. Is principally concerned with gamma-radiation rate-sensing systems. Annex A refers to the

14608,IS,,ISO 7755-1:1984,Hardmetal burrs — Part 1: General specifications,Fraises-limes en métaux-durs — Partie 1: Spécifications générales,1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62910],"['en','fr']",4,"<p>Lays down the common characteristics of these burrs of varous styles, in solid construction or with brazed shank. The main dimensions of the cutting part of hardmetal burrs are dealt with individually in ISO 7755 part 2 to 12. Gives dimensions, directions of flute helix and direction of cut and designation. A table gives the types and the corresponding figures of the burrs.</p>"

14617,IS,,ISO 7755-10:1984,Hardmetal burrs — Part 10: Conical round- (ball-) nose burrs (style L),Fraises-limes en métaux-durs — Partie 10: Fraises-limes coniques à bout rond (forme L),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62919],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardmetal burrs of cone shape, with a round- (ball-) nose and designated by the symbol L. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14618,IS,,ISO 7755-11:1984,Hardmetal burrs — Part 11: Conical pointed-nose burrs (style M),Fraises-limes en métaux-durs — Partie 11: Fraises-limes coniques à bout pointu (forme M),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62920],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardmetal burrs of cone shape, with a pointed nose and designated by the symbol M. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1</p>"

14619,IS,,ISO 7755-12:1984,Hardmetal burrs — Part 12: Inverted cone burrs (style N),Fraises-limes en métaux-durs — Partie 12: Fraises-limes à cône inverse (forme N),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62921],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardmetal burrs of inverted con shape and designated by the symbol N. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14609,IS,,ISO 7755-2:1984,Hardmetal burrs — Part 2: Cylindrical burrs (style A),Fraises-limes en métaux-durs — Partie 2: Fraises-limes cylindriques (forme A),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62911],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardmetal burrs of cylindrical shape and designated by the symbol A. Tolerances on the cutting diameter, direction of helix and cut, diameter and lenth of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14610,IS,,ISO 7755-3:1984,Hardmetal burrs — Part 3: Cylindrical round- (ball-) nose burrs (style C),Fraises-limes en métaux-durs — Partie 3: Fraises-limes cylindriques à bout rond (forme C),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62912],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardmetal burrs of cylindrical shape, with a round- (ball-) nose and designated by the symbol C. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1</p>"

14611,IS,,ISO 7755-4:1984,Hardmetal burrs — Part 4: Spherical burrs (style D),Fraises-limes en métaux-durs — Partie 4: Fraises-limes sphériques (forme D),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62913],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardmetal burrs of spherical shape and designated by the symbol D. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14612,IS,,ISO 7755-5:1984,Hardmetal burrs — Part 5: Oval burrs (style E),Fraises-limes en métaux-durs — Partie 5: Fraises-limes ovales (forme E),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62914],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardmetal burrs of oval shape and designated by the symbol E. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14613,IS,,ISO 7755-6:1984,Hardmetal burrs — Part 6: Arch round- (ball-) nose burrs (style F),Fraises-limes en métaux-durs — Partie 6: Fraises-limes ogives à bout rond (forme F),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62915],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for harmetal burrs of arch shape, with a round- (ball-) nose and designated by the symbol F. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14614,IS,,ISO 7755-7:1984,Hardmetal burrs — Part 7: Arch pointed-nose burrs (style G),Fraises-limes en métaux-durs — Partie 7: Fraises-limes ogives à bout pointu (forme G),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62916],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main diemsnions of the cutting part for hardmetal burrs of arch shape , with a pointed nose and designated by the symbol G. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14615,IS,,ISO 7755-8:1984,Hardmetal burrs — Part 8: Flame burrs (style H),Fraises-limes en métaux-durs — Partie 8: Fraises-limes flammes (forme H),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62917],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardnmetal burrs of flame shape and designated by the symbol H. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14616,IS,,ISO 7755-9:1984,Hardmetal burrs — Part 9: 60 degrees and 90 degrees cone burrs (styles J and K),Fraises-limes en métaux-durs — Partie 9: Fraises-limes coniques 60 degrés et 90 degrés (formes J et K),1984-11-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[62918],"['en','fr']",1,"<p>This part of ISO 7755 lays down the main dimensions of the cutting part for hardmetal burrs of 60 cone and 90 cone shape and designated by the symbols J and K. Tolerances on the cutting diameter, direction of helix and cut, diameter and length of the cylindrical shank and designation of burrs are dealt with in ISO 7755-1.</p>"

14623,IS,,ISO 7759:1983,Anodizing of aluminium and its alloys — Measurement of reflectivity characteristics of aluminium surfaces using abridged goniophotometer or goniophotometer,Anodisation de l'aluminium et de ses alliages — Mesurage des caractéristiques de réflectivité des surfaces d'aluminium à l'aide d'un goniophotomètre simplifié ou normal,1983-12-01,1,['25.220.20'],ISO/TC 79/SC 2,9599,,[51494],"['en','fr']",5,"<p>Specifies a method for the measurement of the reflectivity characteristics responsible for the appearance of high-gloss metal surfaces. The method is not suitable for diffuse-finish metal surfaces, nor does it measure colour, which is another appearance attribute. Precision

5062,IS,,ISO 776:1982,Pulps — Determination of acid-insoluble ash,Pâtes — Détermination des cendres insolubles dans l'acide,1982-12-01,2,['85.040'],ISO/TC 6,9599,,[52672],"['en','fr']",2,<p>Is applicable to all kinds of pulps. The ash obtained is treated with hydrochloric acid.</p>

14624,IS,,ISO 7760:1986,Photographic processing waste — Determination of hydroquinone content — Spectrophotometric method,Déchets des traitements photographiques — Dosage de l'hydroquinone — Méthode spectrophotométrique,1986-04-17,1,"['37.040.30','13.030.30']",ISO/TC 42,9599,,"[20061,32495]","['en','fr']",3,<p>The method can be applied to samples containing hydroquinone in the concentration range of 200 to 4000 g/l. Aminophenols and phenylenediamines should also be determined by this method.</p>

14628,IS,,ISO 7764:1985,Iron ores — Preparation of predried test samples for chemical analysis,Minerais de fer — Préparation des échantillons préséchés pour analyse chimique,1985-04-11,1,['73.060.10'],ISO/TC 102/SC 2,9599,,[35007],"['en','fr']",2,

14630,IS,,ISO 7765-2:1994,Plastics film and sheeting — Determination of impact resistance by the free-falling dart method — Part 2: Instrumented puncture test,Film et feuille de plastiques — Détermination de la résistance au choc par la méthode par chute libre de projectile — Partie 2: Essai avec appareil de perforation,1994-08-04,1,['83.140.10'],ISO/TC 61/SC 11,9599,,[81986],"['en','fr']",10,"<p>The impact-penetration test described is used for the assessment of plastic films and thin sheets under an impact stress applied at right angles to the plane of the film. This part 2 is used if a force-deformation or a force-time diagram, recorded at practically constant velocity of the striker, is

81986,IS,,ISO 7765-2:2022,Plastics film and sheeting — Determination of impact resistance by the free-falling dart method — Part 2: Instrumented puncture test,Film et feuille de plastiques — Détermination de la résistance au choc par la méthode par chute libre de projectile — Partie 2: Essai avec appareil de perforation,2022-05-20,2,['83.140.10'],ISO/TC 61/SC 11,9599,[14630],[88049],['en'],15,"<p>This document specifies a test method for the determination of puncture impact properties of a plastic film using instruments for measuring force and deflection. It is applicable if a force-deflection or force-time diagram, recorded at nominally constant striker velocity, is required for detailed ch

14631,IS,,ISO 7766-1:1993,Photography — Processing wastes — Analysis of cyanides — Part 1: Determination of hexacyanoferrate(II) and hexacyanoferrate(III) by spectrometry,Photographie — Effluents de traitement — Analyse des cyanures — Partie 1: Détermination de l'hexacyanoferrate(II) et de l'hexacyanoferrate(III) par spectrométrie,1993-01-21,1,"['37.040.30','13.030.30']",ISO/TC 42,9599,,[34988],['en'],5,"<p>The principle of the test method specified is treating a sample of effluent, or diluted effluent, with a mixture of iron(II) and iron(III) ions. If Fe(CN)₆ is present, a blue suspension will form. In the range of 1,0 mg/l to 10,0 mg/l, this suspension is stable and its absorban

22622,IS,,ISO 7767:1997,Oxygen monitors for monitoring patient breathing mixtures — Safety requirements,Analyseurs d'oxygène pour le contrôle des mélanges gazeux respirés par le patient — Exigences de sécurité,1997-04-24,2,['11.040.10'],ISO/TC 121/SC 1,9599,,"[34637,33781]",['en'],30,

14635,IS,,ISO 7768:1985,Textiles — Method for assessing the appearance of durable press fabrics after domestic washing and drying,Textiles — Méthode d'essai pour l'évaluation de l'aspect des étoffes traitées 'pressage permanent' après le lavage et le séchage domestiques,1985-05-23,1,['59.080.30'],ISO/TC 38/SC 2,9599,,[38657],"['en','fr']",4,"<p>Specifies a method for assessing the retention of the original smooth appearance, after one or several domestic washing and drying treatments, of those fabrics intended for use in durable press (sometimes referred to as permanent press) products. Fabric specimens are subjected to procedures simulating domestic laundering practices. One of the washing

38657,IS,,ISO 7768:2006,Textiles — Test method for assessing the smoothness appearance of fabrics after cleansing,Textiles — Méthode d'essai pour l'évaluation de la régularité d'aspect des étoffes après nettoyage,2006-02-10,2,['59.080.30'],ISO/TC 38/SC 2,9599,[14635],[52694],"['en','fr']",6,"<p>ISO 7768:2006 specifies a method for assessing the retention of the original smooth appearance, after one or several cleansing treatments, of the fabrics tested.This method has been developed for use primarily with type B domestic washing machines, as defined in ISO 6330, in the cleansing process. However, it may be possible to use it with machines of type A. This test method could be used for judgin

14636,IS,,ISO 7769:1985,Textiles — Method for assessing the appearance of creases in durable press products after domestic washing and drying,Textiles — Méthode d'essai pour l'évaluation de l'aspect des plis des étoffes traitées 'pressage permanent' après le lavage et le séchage domestiques,1985-04-18,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[14637],"['en','fr']",4,

14637,IS,,ISO 7769:1992,Textiles — Method for assessing the appearance of creases in durable-press products after domestic washing and drying,Textiles — Méthode d'essai pour l'évaluation de l'aspect des plis des étoffes traitées 'plissage permanent' après le lavage et le séchage domestiques,1992-11-19,2,['59.080.30'],ISO/TC 38/SC 2,9599,[14636],[38681],"['en','fr']",6,<p>The method is based on subjecting the specimens to procedures simulating domestic laundering practices (one of the washing and drying procedures specified in ISO 6330 is usually used). Evaluation is performed by supplementing the overhead lighting arrangement with a spotlight suitably placed to highlight the creased area. Th

38681,IS,,ISO 7769:2006,Textiles — Test method for assessing the appearance of creases in fabrics after cleansing,Textiles — Méthode d'essai pour l'évaluation de l'aspect des plis des étoffes après nettoyage,2006-02-10,3,['59.080.30'],ISO/TC 38/SC 2,9599,[14637],[52693],"['en','fr']",8,"<p>ISO 7769:2006 specifies a test method for evaluating the retention of pressed-in creases in fabrics after one or several cleansing treatments. A technique for inserting creases is not included as this is controlled by fabric properties. This method has been developed for use primarily with type B domestic washing machines, as defined in ISO 6330, in the cleansing process. However, it may be possible to use

5063,IS,,ISO 777:1982,Pulps — Determination of calcium content — EDTA titrimetric and flame atomic absorption spectrometric methods,Pâtes — Détermination de la teneur en calcium — Méthode titrimétrique à l'EDTA et méthode par spectrométrie d'absorption atomique de flamme,1982-08-01,1,['85.040'],ISO/TC 6,9599,,[31803],"['en','fr']",5,

31803,IS,,ISO 777:2001,"Paper, board and pulp — Determination of calcium","Papier, carton et pâte — Détermination de la teneur en calcium",2001-05-24,2,['85.040'],ISO/TC 6,9599,[5063],[41587],"['en','fr']",6,

41587,IS,,ISO 777:2005,"Paper, board and pulp — Determination of acid-soluble calcium","Papier, carton et pâte — Détermination de la teneur en calcium soluble dans l'acide",2005-04-27,3,"['85.060','85.040']",ISO/TC 6,9599,[31803],[51848],"['en','fr','ru']",6,"<p>ISO 777:2005 specifies the procedure for the determination of acid-soluble calcium by atomic absorption spectrometry or by plasma emission spectrometry.</p><p>It is applicable to all kinds of paper, board and pulp.</p><p>It specifies a method to determine the acid-soluble part of the incineration residue, i.e. that part of the ignition residue obtained after incineration that is soluble in hydrochloric acid. If the residue is complet

14638,IS,,ISO 7770:1985,Textiles — Method for assessing the appearance of seams in durable press products after domestic washing and drying,Textiles — Méthodes d'essai pour l'évaluation de l'aspect des coutures sur les étoffes traitées 'pressage permanent' après le lavage et le séchage domestiques,1985-04-18,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[38682],"['en','fr']",4,<p>Seamed fabric specimens are subjected to procedures simulating domestic laundering practices. One of the washing and drying procedures specified in ISO 6330 shall be used. The specimens are compared visually with photographic standards under defined illumination.</p>

38682,IS,,ISO 7770:2006,Textiles — Test method for assessing the smoothness appearance of seams in fabrics after cleansing,Textiles — Méthode d'essai pour l'évaluation de la régularité d'aspect des coutures sur les étoffes après nettoyage,2006-02-10,2,['59.080.30'],ISO/TC 38/SC 2,9599,[14638],[52692],"['en','fr']",8,"<p>ISO 7770:2006 specifies a test method for evaluating the smoothness appearance of seams in fabrics, after one or several cleansing treatments. A seaming technique is not included, since the purpose is to evaluate existing seams. This method has been developed for use primarily with type B domestic washing machines, as defined in ISO 6330, in the cleansing process. However, it

14648,IS,,ISO 7775-1:1984,Securities — Standard scheme for message types — Part 1: Receipt/delivery,Valeurs mobilières — Plan de norme pour les types de messages — Partie 1: Réception/livraison,1984-10-01,1,['03.060'],ISO/TC 68,9599,,[14646],"['en','fr']",20,

14646,IS,,ISO 7775:1991,Securities — Scheme for message types,Valeurs mobilières — Types de messages,1991-11-14,1,['03.060'],ISO/TC 68,9599,"[14648,14649]","[26156,27999]","['en','fr']",51,

14649,IS,,ISO 7775-2:1986,Securities — Scheme for message types — Part 2: Order to buy/sell,Valeurs mobilières — Structure des types de messages — Partie 2: Ordre d'achat/de vente,1986-02-06,1,['03.060'],ISO/TC 68,9599,,[14646],"['en','fr']",16,

14652,IS,,ISO 7776:1986,Information processing systems — Data communications — High-level data link control procedures — Description of the X.25 LAPB-compatible DTE data link procedures,Téléinformatique — Procédures de commande de liaison de données à haut niveau — Description des procédures de liaison d'équipement terminal de transmission de données ETTD compatible X.25 LAPB,1986-12-30,1,['35.100.20'],ISO/IEC JTC 1/SC 6,9599,,[22172],"['en','fr']",23,

14653,IS,Amd,ISO 7776:1986/Amd 1:1992,Information processing systems — Data communications — High-level data link control procedures — Description of the X.25 LAPB-compatible DTE data link procedures — Amendment 1,Téléinformatique — Procédures de commande de liaison de données à haut niveau — Description des procédures de liaison d'équipement terminal de transmission de données ETTD compatible X.25 LAPB — Amendement 1,1992-12-30,1,['35.100.20'],ISO/IEC JTC 1/SC 6,9599,,[22172],['en'],12,

14654,IS,Cor,ISO 7776:1986/Cor 1:1989,Information processing systems — Data communications — High-level data link control procedures — Description of the X.25 LAPB-compatible DTE data link procedures — Technical Corrigendum 1,Téléinformatique — Procédures de commande de liaison de données à haut niveau — Description des procédures de liaison d'équipement terminal de transmission de données ETTD compatible X.25 LAPB — Rectificatif technique 1,1989-03-23,1,['35.100.20'],ISO/IEC JTC 1/SC 6,9599,,[22172],"['en','fr']",1,

14655,IS,Cor,ISO 7776:1986/Cor 2:1989,Information processing systems — Data communications — High-level data link control procedures — Description of the X.25 LAPB-compatible DTE data link procedures — Technical Corrigendum 2,Téléinformatique — Procédures de commande de liaison de données à haut niveau — Description des procédures de liaison d'équipement terminal de transmission de données ETTD compatible X.25 LAPB — Rectificatif technique 2,1989-08-31,1,['35.100.20'],ISO/IEC JTC 1/SC 6,9599,,[22172],['en'],1,

14656,IS,Cor,ISO 7776:1986/Cor 3:1991,Information processing systems — Data communications — High-level data link control procedures — Description of the X.25 LAPB-compatible DTE data link procedures — Technical Corrigendum 3,Téléinformatique — Procédures de commande de liaison de données à haut niveau — Description des procédures de liaison d'équipement terminal de transmission de données ETTD compatible X.25 LAPB — Rectificatif technique 3,1991-03-01,1,['35.100.20'],ISO/IEC JTC 1/SC 6,9599,,[22172],"['en','fr']",1,

14658,IS,,ISO 7778:1983,Steel plate with specified through-thickness characteristics,Tôles en acier avec caractéristiques garanties dans le sens de l'épaisseur,1983-09-01,1,['77.140.50'],ISO/TC 17/SC 3,9599,,[59632],"['en','fr']",4,"<p>Specifies the criteria which shall be satisfied by the qualities of steel plate and wide flats for which trough-tickness reduction of area properties are specified in the direction of thickness perpendicular to the surface, and also the test conditions. Applies to thicknesses between 15 mm and 150 mm inclusive of fully killed steel with a specified minimum yield strength equal to or less than 500 N/mm .</p>"

14659,IS,,ISO 7779:1988,Acoustics — Measurement of airborne noise emitted by computer and business equipment,Acoustique — Mesurage du bruit aérien émis par les équipements informatiques et de bureau,1988-06-23,1,"['35.020','17.140.20']",ISO/TC 43/SC 1,9599,,[24919],"['en','fr']",39,

24919,IS,,ISO 7779:1999,Acoustics — Measurement of airborne noise emitted by information technology and telecommunications equipment,Acoustique — Mesurage du bruit aérien émis par les équipements liés aux technologies de l'information et aux télécommunications,1999-08-12,2,"['35.020','17.140.20']",ISO/TC 43/SC 1,9599,[14659],[54363],"['en','fr']",61,

34559,IS,Amd,ISO 7779:1999/Amd 1:2003,Acoustics — Measurement of airborne noise emitted by information technology and telecommunications equipment — Amendment 1: Noise measurement specification for CD/DVD-ROM drives,Acoustique — Mesurage du bruit aérien émis par les équipements liés aux technologies de l'information et aux télécommunications — Amendement 1: Spécifications relatives au mesurage du bruit pour les lecteurs de CD/DVD-ROM,2003-03-05,2,"['35.020','17.140.20']",ISO/TC 43/SC 1,9599,,[54363],"['en','fr']",4,

54363,IS,,ISO 7779:2010,Acoustics — Measurement of airborne noise emitted by information technology and telecommunications equipment,Acoustique — Mesurage du bruit aérien émis par les équipements liés aux technologies de l'information et aux télécommunications,2010-07-29,3,"['35.020','17.140.20']",ISO/TC 43/SC 1,9599,"[34559,40137,24919]",[69857],"['en','fr']",62,"<p>ISO 7779:2010 specifies procedures for measuring and reporting the noise emission of information technology and telecommunications equipment.</p><p>The basic emission quantity is the A-weighted sound power level which may be used for comparing equipment of the same type but from different manufacturers, or for comparing differen

5064,IS,,ISO 778:1982,Pulps — Determination of copper content — Extraction-photometric and flame atomic absorption spectrometric methods,Pâtes — Détermination de la teneur en cuivre — Méthode par extraction et photométrie et méthode par spectrométrie d'absorption atomique de flamme,1982-08-01,1,['85.040'],ISO/TC 6,9599,,[31804],"['en','fr']",4,

31804,IS,,ISO 778:2001,"Paper, board and pulp — Determination of copper","Papier, carton et pâte — Détermination de la teneur en cuivre",2001-05-24,2,['85.040'],ISO/TC 6,9599,[5064],[41588],"['en','fr']",6,

41588,IS,,ISO 778:2005,"Paper, board and pulp — Determination of acid-soluble copper","Papier, carton et pâte — Détermination de la teneur en cuivre soluble dans l'acide",2005-04-27,3,"['85.060','85.040']",ISO/TC 6,9599,[31804],[51848],"['en','fr','ru']",6,"<p>ISO 778:2005 specifies the procedure for the determination of acid-soluble copper by atomic absorption spectrometry or by plasma emission spectrometry.</p><p>It is applicable to all types of paper, board and pulp.</p><p>It specifies a method to determine the acid-soluble part of the incineration residue, i.e. that part of the ignition residue obtained after incineration which is soluble in hydrochloric acid. If the residue is completel

14660,IS,,ISO 7780:1987,Rubbers and rubber latices — Determination of manganese content — Sodium periodate photometric methods,Caoutchoucs et latex de caoutchoucs — Dosage du manganèse — Méthodes photométriques au periodate de sodium,1987-05-21,1,"['83.060','83.040.10']",ISO/TC 45,9599,"[5983,6271]",[14661],"['en','fr']",6,

14662,IS,,ISO 7781:1986,"Rubber, raw styrene-butadiene — Soap and organic acid content — Determination",Caoutchouc butadiène-styrène brut — Détermination de la teneur en savons et acides organiques,1986-10-16,1,['83.040.10'],ISO/TC 45,9599,"[6763,6762]",[20153],"['en','fr']",4,

20153,IS,,ISO 7781:1996,"Rubber, raw styrene-butadiene — Determination of soap and organic-acid content",Caoutchouc butadiène-styrène brut — Détermination de la teneur en savons et acides organiques,1996-10-31,2,['83.040.10'],ISO/TC 45/SC 2,9599,[14662],[33841],"['en','fr']",4,<p>Describes a method for the determination of the soap and organic-acid content of raw styrene-butadiene rubber (SBR). The method depends on the extraction of the organic acids and soaps from the rubber by means of a solvent. Recommends to determine both contents on separate portions of the same solvent extract; gives only an approximative value. Replaces the first edition.</p>

33841,IS,,ISO 7781:2001,"Styrene-butadiene rubber, raw — Determination of soap and organic-acid content",Caoutchouc butadiène-styrène brut — Détermination de la teneur en savons et acides organiques,2001-12-06,3,['83.040.10'],ISO/TC 45/SC 2,9599,[20153],[45393],['en'],6,

45393,IS,,ISO 7781:2008,"Styrene-butadiene rubber, raw — Determination of soap and organic-acid content",Caoutchouc butadiène-styrène brut — Détermination de la teneur en savons et acides organiques,2008-03-20,4,['83.040.10'],ISO/TC 45/SC 3,9599,[33841],[68071],['en'],7,"<p>ISO 7781:2008 specifies methods for the determination of the soap and organic-acid content of raw styrene-butadiene rubber (SBR). Method A is the titration method using indicator reagent. Method B is the titration method using an autotitrator or pH-meter.</p><p>The methods depend on the extraction of the organic acids and soaps from the rubber by means of a specified solvent. In practice, therefore, it is convenient to d

14664,IS,,ISO 7783-1:1996,Paints and varnishes — Determination of water-vapour transmission rate — Part 1: Dish method for free films,Peintures et vernis — Détermination du coefficient de transmission de la vapeur d'eau — Partie 1: Méthode de la capsule pour feuils libres,1996-06-20,1,['87.040'],ISO/TC 35/SC 9,9599,,[46283],"['en','fr']",10,

30958,IS,Cor,ISO 7783-1:1996/Cor 1:1998,Paints and varnishes — Determination of water-vapour transmission rate — Part 1: Dish method for free films — Technical Corrigendum 1,Peintures et vernis — Détermination du coefficient de transmission de la vapeur d'eau — Partie 1: Méthode de la capsule pour feuils libres — Rectificatif technique 1,1998-09-17,1,['87.040'],ISO/TC 35/SC 9,9599,,[46283],"['en','fr']",1,

19456,IS,,ISO 7783-2:1999,Paints and varnishes — Coating materials and coating systems for exterior masonry and concrete — Part 2: Determination and classification of water-vapour transmission rate (permeability),Peintures et vernis — Produits de peinture et systèmes de revêtement pour maçonnerie et béton extérieurs — Partie 2: Détermination et classification du taux de transmission de la vapeur d'eau (perméabilité),1999-03-18,1,['87.040'],ISO/TC 35/SC 9,9599,,[46283],"['en','fr']",7,

46283,IS,,ISO 7783:2011,Paints and varnishes — Determination of water-vapour transmission properties — Cup method,Peintures et vernis — Détermination des propriétés de transmission de la vapeur d'eau — Méthode de la coupelle,2011-10-28,1,['87.040'],ISO/TC 35/SC 9,9599,"[14664,30958,19456]",[70904],"['en','fr','ru']",18,

14665,IS,,ISO 7784-1:1997,Paints and varnishes — Determination of resistance to abrasion — Part 1: Rotating abrasive-paper-covered wheel method,Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 1: Méthode utilisant une roue revêtue de papier abrasif,1997-02-06,1,['87.040'],ISO/TC 35/SC 9,9599,,[62344],"['en','fr']",9,"<p>Deals with the sampling and testing of paints, varnishes and related products. Gives a method for the determination of the resistance to abrasion of a dried coating, using abrasive paper attached to a wheel and abrading rotation.</p>"

62344,IS,,ISO 7784-1:2016,Paints and varnishes — Determination of resistance to abrasion — Part 1: Method with abrasive-paper covered wheels and rotating test specimen,Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 1: Méthode utilisant des roues revêtues de papier abrasif et une éprouvette rotative,2016-03-10,2,['87.040'],ISO/TC 35/SC 9,9599,[14665],[83327],"['en','fr']",7,"<p>ISO 7784-1:2016 specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive-paper covered wheels affect the coating of the rotating test specimens.</p>"

23237,IS,,ISO 7784-2:1997,Paints and varnishes — Determination of resistance to abrasion — Part 2: Rotating abrasive rubber wheel method,Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 2: Méthode utilisant une roue abrasive en caoutchouc,1997-02-06,1,['87.040'],ISO/TC 35/SC 9,9599,,[62345],"['en','fr']",10,"<p>Deals with the sampling and testing of paints, varnishes and related products. Gives a method for the determination of the resistance to abrasion of a dried coating, using an abrasive rubber wheel and abrading by rotation.</p>"

62345,IS,,ISO 7784-2:2016,Paints and varnishes — Determination of resistance to abrasion — Part 2: Method with abrasive rubber wheels and rotating test specimen,Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 2: Méthode utilisant des roues abrasives en caoutchouc et une éprouvette rotative,2016-03-10,2,['87.040'],ISO/TC 35/SC 9,9599,[23237],[83328],"['en','fr']",7,"<p>ISO 7784-2:2016 specifies a method for determining the resistance to abrasion of coatings, for which two loaded, freely rotatable but eccentrically arranged abrasive rubber wheels affect the coating of the rotating test specimen.</p>"

22383,IS,,ISO 7784-3:2000,Paints and varnishes — Determination of resistance to abrasion — Part 3: Reciprocating test panel method,Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 3: Méthode de panneau d'essai animé d'un mouvement de va-et-vient,2000-03-16,1,['87.040'],ISO/TC 35/SC 9,9599,,[64796],"['en','fr']",9,

64796,IS,,ISO 7784-3:2016,Paints and varnishes — Determination of resistance to abrasion — Part 3: Method with abrasive-paper covered wheel and linearly reciprocating test specimen,Peintures et vernis — Détermination de la résistance à l'abrasion — Partie 3: Méthode utilisant une roue revêtue de papier abrasif et une éprouvette animée d'un mouvement de va-et-vient linéaire,2016-03-10,2,['87.040'],ISO/TC 35/SC 9,9599,[22383],[83329],"['en','fr']",8,"<p>ISO 7784-3:2016 specifies a method for determining the resistance to abrasion of coatings, for which a loaded, rigid abrasive-paper covered wheel affects the coating of the linearly reciprocating test specimen.</p>"

14666,IS,,ISO 7785-1:1992,Dental handpieces — Part 1: High-speed air-turbine handpieces,Pièces à main dentaires — Partie 1: Pièces à main à turbines à air comprimé pour grandes vitesses,1992-12-17,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[22723],"['en','fr']",6,

22723,IS,,ISO 7785-1:1997,Dental handpieces — Part 1: High-speed air turbine handpieces,Pièces à main dentaires — Partie 1: Pièces à main à turbines à air comprimé pour grandes vitesses,1997-07-31,2,['11.060.20'],ISO/TC 106/SC 4,9599,[14666],[54805],"['en','fr']",10,

14667,IS,,ISO 7785-2:1991,Dental handpieces — Part 2: Straight and geared angle handpieces,Pièces à main dentaires — Partie 2: Pièces à main rectilignes et à contre-angles,1991-10-03,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[20415],"['en','fr']",6,

20415,IS,,ISO 7785-2:1995,Dental handpieces — Part 2: Straight and geared angle handpieces,Pièces à main dentaires — Partie 2: Pièces à main rectilignes et à contre-angles,1995-07-27,2,['11.060.20'],ISO/TC 106/SC 4,9599,[14667],[54805],"['en','fr']",7,"<p>Specifies requirements and test methods for straight and geared angle dental hand instruments for application to patients. Contains also specifications on manufacturer's instructions, marking and packaging.</p>"

14670,IS,,ISO 7786:1984,Dental rotary instruments — Laboratory abrasive instruments,Instruments rotatifs dentaires — Instruments abrasifs de laboratoire,1984-08-01,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[14671],"['en','fr']",4,

14671,IS,,ISO 7786:1990,Dental rotary instruments — Laboratory abrasive instruments,Instruments rotatifs dentaires — Instruments abrasifs de laboratoire,1990-08-23,2,['11.060.20'],ISO/TC 106/SC 4,9599,[14670],[26728],"['en','fr']",7,

14672,IS,,ISO 7787-1:1984,Dental rotary instruments — Cutters — Part 1: Steel laboratory cutters,Instruments rotatifs dentaires — Fraises techniques — Partie 1: Fraises techniques en acier,1984-12-01,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[66427],"['en','fr']",6,"<p>Specification of the dimensional and other requirements, that are considered important to ensure the interchangeability of these instruments, for the nine most commonly used steel cutters. Other characteristics of cutters, for example spiralled blades or cross-cut, are not included. Attention is drawn to ISO 6360 which specifies a 15 digit number for the identification of all types of these rotary instruments.</p>"

14673,IS,,ISO 7787-2:1984,Dental rotary instruments — Cutters — Part 2: Carbide laboratory cutters,Instruments rotatifs dentaires — Fraises techniques — Partie 2: Fraises techniques en carbure,1984-12-01,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[14674],"['en','fr']",6,

14674,IS,,ISO 7787-2:1992,Dental rotary instruments — Cutters — Part 2: Carbide laboratory cutters,Instruments rotatifs dentaires — Fraises techniques — Partie 2: Fraises techniques en carbure,1992-11-12,2,['11.060.20'],ISO/TC 106/SC 4,9599,[14673],[27139],"['en','fr']",11,

27139,IS,,ISO 7787-2:1998,Dental rotary instruments — Cutters — Part 2: Carbide laboratory cutters,Instruments rotatifs dentaires — Fraises techniques — Partie 2: Fraises techniques en carbure,1998-07-16,3,['11.060.20'],ISO/TC 106/SC 4,9599,[14674],[31247],"['en','fr']",12,

31247,IS,,ISO 7787-2:2000,Dental rotary instruments — Cutters — Part 2: Carbide laboratory cutters,Instruments rotatifs dentaires — Fraises techniques — Partie 2: Fraises techniques en carbure,2000-12-21,4,['11.060.20'],ISO/TC 106/SC 4,9599,[27139],[73459],"['en','fr']",10,

14675,IS,,ISO 7787-3:1991,Dental rotary instruments — Cutters — Part 3: Carbide laboratory cutters for milling machines,Instruments rotatifs dentaires — Fraises techniques — Partie 3: Fraises techniques en carbure pour machines de meulage,1991-12-05,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[68488],"['en','fr']",4,"<p>Specifies the dimensional and other requirements for the three most commonly used cutters with nominal sizes 010, 015, 023. A cylindrical cutter for side cutting only is shown in figure 1. A hemispherical, cylindrical cutter is shown in figure 2.</p>"

14676,IS,,ISO 7788:1985,Steel — Surface finish of hot-rolled plates and wide flats — Delivery requirements,Acier — État de surface des tôles et larges-plats laminés à chaud — Conditions de livraison,1985-12-19,1,['77.140.50'],ISO/TC 17/SC 3,9599,,[73845],"['en','fr']",8,"<p>These plates and wide flats are rolled on reversing mills. They have nominal thicknesses equal to or less than 150 mm. ISO 7788 specifies requirements, repair procedures, and in annex A definitions of products and discontinuities.</p>"

14677,IS,,ISO 7789:1998,"Hydraulic fluid power — Two-, three- and four-port screw-in cartridge valves — Cavities","Transmissions hydrauliques — Distributeurs à cartouche à visser à deux, trois et quatre orifices — Logements",1998-04-23,1,['23.100.50'],ISO/TC 131/SC 5,9599,,[40310],"['en','fr']",24,

31109,IS,Cor,ISO 7789:1998/Cor 1:1999,"Hydraulic fluid power — Two-, three- and four-port screw-in cartridge valves — Cavities — Technical Corrigendum 1","Transmissions hydrauliques — Distributeurs à cartouche à visser à deux, trois et quatre orifices — Logements — Rectificatif technique 1",1999-02-25,1,['23.100.50'],ISO/TC 131/SC 5,9599,,[40310],"['en','fr']",2,

5065,IS,,ISO 779:1982,"Pulps — Determination of iron content — 1,10-Phenanthroline photometric and flame atomic absorption spectrometric methods","Pâtes — Détermination de la teneur en fer — Méthode photométrique à la phénanthroline-1,10 et méthode par spectrométrie d'absorption atomique de flamme",1982-08-01,1,['85.040'],ISO/TC 6,9599,,[31805],"['en','fr']",4,

31805,IS,,ISO 779:2001,"Paper, board and pulp — Determination of iron","Papier, carton et pâte — Détermination de la teneur en fer",2001-05-24,2,['85.040'],ISO/TC 6,9599,[5065],[41589],"['en','fr']",6,

41589,IS,,ISO 779:2005,"Paper, board and pulp — Determination of acid-soluble iron","Papier, carton et pâte — Détermination de la teneur en fer soluble dans l'acide",2005-04-27,3,"['85.060','85.040']",ISO/TC 6,9599,[31805],[51848],"['en','fr','ru']",6,"<p>ISO 779:2005 specifies the procedure for the determination of acid-soluble iron by atomic absorption spectrometry or by plasma emission spectrometry. </p><p>It is applicable to all kinds of paper, board and pulp.</p><p>It specifies a method to determine the acid-soluble part of the incineration residue, i.e. that part of the ignition residue obtained after incineration which is soluble in hydrochloric acid. If the residue is completely solu

14678,IS,,ISO 7790:1986,"Hydraulic fluid power — Four-port modular stack valves and four-port directional control valves, sizes 03 and 05 — Clamping dimensions","Transmissions hydrauliques — Appareils empilables et distributeurs à quatre orifices, de tailles 03 et 05 — Dimensions de montage",1986-07-17,1,['23.100.50'],ISO/TC 131/SC 5,9599,,[14679],"['en','fr']",2,

14679,IS,,ISO 7790:1997,"Hydraulic fluid power — Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 — Clamping dimensions","Transmissions hydrauliques — Appareils empilables et distributeurs à quatre orifices, de tailles 02, 03 et 05 — Dimensions de montage",1997-12-11,2,['23.100.50'],ISO/TC 131/SC 5,9599,[14678],[53397],"['en','fr']",4,

14683,IS,,ISO 7792-1:1985,Plastics — Polyalkylene terephthalates — Part 1: Designation,Plastiques — Polyalkylène téréphtalates — Partie 1: Désignation,1985-12-19,1,['83.080.20'],ISO/TC 61/SC 9,9599,,"[25654,23948]","['en','fr']",5,

23948,IS,,ISO 7792-1:1995,Plastics — Poly(alkylene terephthalate) moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Poly(alkylène téréphtalates) pour moulage et extrusion — Partie 1: Système de désignation et base de spécification,1995-09-28,2,['83.080.20'],ISO/TC 61/SC 9,9599,[14683],[25654],"['en','fr']",7,

25654,IS,,ISO 7792-1:1997,Plastics — Thermoplastic polyester (TP) moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Polyesters thermoplastiques (TP) pour moulage et extrusion — Partie 1: Système de désignation et base de spécification,1997-12-18,3,['83.080.20'],ISO/TC 61/SC 9,9599,"[23948,14683]","[55479,50592]","['en','fr']",11,

55479,IS,,ISO 7792-1:2012,Plastics — Thermoplastic polyester (TP) moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Polyesters thermoplastiques (TP) pour moulage et extrusion — Partie 1: Système de désignation et base de spécification,2012-11-28,4,['83.080.20'],ISO/TC 61/SC 9,9599,[25654],[66866],"['en','fr']",14,"<p>ISO 7792-1:2012 establishes a system of designation for thermoplastic polyester (TP) material, which may be used as the basis for specifications. It covers polyester homopolymers for moulding and extrusion based on poly(ethylene terephthalate) (PET), poly(butylene terephthalate) (PBT), poly(cyclohexylenedimethylene terephtha

14684,IS,,ISO 7792-2:1988,Plastics — Polyalkylene terephthalates — Part 2: Preparation of test specimens and determination of properties,Plastiques — Polyalkylène téréphtalates — Partie 2: Préparation des éprouvettes et détermination des caractéristiques,1988-11-24,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[25184],"['en','fr']",3,

25184,IS,,ISO 7792-2:1997,Plastics — Thermoplastic polyester (TP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Polyesters thermoplastiques (TP) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés,1997-12-18,2,['83.080.20'],ISO/TC 61/SC 9,9599,[14684],"[55480,50593]","['en','fr']",6,

55480,IS,,ISO 7792-2:2012,Plastics — Thermoplastic polyester (TP) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Polyesters thermoplastiques (TP) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés,2012-11-28,3,['83.080.20'],ISO/TC 61/SC 9,9599,[25184],[66867],"['en','fr']",6,"<p>ISO 7792-2:2012 specifies the methods of preparation of test specimens and the standard test methods to be used in determining the properties of thermoplastic polyester moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding

14685,IS,,ISO 7793:1984,Cross-country skis — Binding mounting area — Stripping torque — Requirements and test method,Skis de fond — Zone de montage de la fixation — Résistance au foirage des vis — Spécifications et méthode d'essai,1984-04-01,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[16714],"['en','fr']",3,

14686,IS,,ISO 7794:1984,Cross-country skis — Ski binding screws — Requirements,Skis de fond — Vis de fixation — Spécifications,1984-05-01,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[14687],"['en','fr']",3,

14687,IS,,ISO 7794:1991,Cross-country skis — Ski binding screws — Requirements,Skis de fond — Vis de fixation — Spécifications,1991-07-18,2,['97.220.20'],ISO/TC 83/SC 4,9599,[14686],[55816],"['en','fr']",2,"<p>Specifies the dimensions, mechanical properties, and fastening characteristics of screws used for mounting ski bindings on cross-country skis. This second edition cancels and replaces the first edition (1984).</p>"

14688,IS,,ISO 7795:1984,Cross-country skis — Ski binding screws — Test methods,Skis de fond — Vis de fixation — Méthodes d'essai,1984-05-01,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[14689],"['en','fr']",5,

14689,IS,,ISO 7795:1994,Cross-country skis — Ski-binding screws — Test methods,Skis de fond — Vis de fixation — Méthodes d'essai,1994-07-21,2,['97.220.20'],ISO/TC 83/SC 4,9599,[14688],[55817],"['en','fr']",4,<p>Specifies test methods for the determination of the mounting and fastening characteristics of screws which are intended for fastening ski binding to cross-country skis. The results of these test methods characterize only the properties of the screw and give no information about the actual mounting and fastening characteristics of different ski models. Requirements are specified in ISO 7794.</p>

14692,IS,,ISO 7798:1984,Cross-country skis — Determination of fatigue indexes — Cyclic loading test,Skis de fond — Détermination des indices de fatigue — Essai en flexion alternée,1984-07-01,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[72501],"['en','fr']",5,"<p>Specifies a methode for the determination of the fatigue indexes, i.e. the resistance of the skis to changes of bottom camber height or irreversible damage, after a bending test with cyclic loading. Is applicable to cross-country skis with a nominal length of 160 cm to 215 cm.</p>"

3725,IS,,ISO 78-2:1982,Layouts for standards — Part 2: Standard for chemical analysis,Plans de normes — Partie 2: Norme d'analyse chimique,1982-04-01,1,['71.040.40'],ISO/TC 47,9599,,[3726],"['en','fr']",12,

3728,IS,,ISO 78-4:1983,Layouts for standards — Part 4: Standard for atomic absorption spectrometric analysis,Plans de normes — Partie 4: Norme d'analyse par spectrométrie d'absorption atomique,1983-02-01,1,['71.040.50'],ISO/TC 47,9599,,[21286],"['en','fr']",5,"<p>Establishes a layout for standard methods of analysis and gives some recommendations for their presentation and wording. This layout involves the use of appropriate terminology, indicated in ISO 6955. Supplements ISO 6956, which summarizes the principle of atomic absorption.</p>"