Withdrawn and superseded ISO standards — page 160 of 246

20991,IS,,ISO 7539-9:2003,Corrosion of metals and alloys — Stress corrosion testing — Part 9: Preparation and use of pre-cracked specimens for tests under rising load or rising displacement,Corrosion des métaux et alliages — Essais de corrosion sous contrainte — Partie 9: Préparation et utilisation des éprouvettes préfissurées pour essais sous charge croissante ou sous déplacement croissant,2003-04-14,1,['77.060'],ISO/TC 156,9599,,[80434],"['en','fr']",27,"<p>ISO 7539-9:2003 covers procedures for designing, preparing and using pre-cracked specimens for investigating the susceptibility of metal to stress corrosion cracking by means of tests conducted under rising load or rising displacement.

14322,IS,,ISO 7540:1984,Ground (powdered) paprika (Capsicum annuum Linnaeus) — Specification,Paprika (Capsicum annuum Linnaeus) en poudre — Spécifications,1984-12-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[39054],"['en','fr']",4,"<p>Specifies the requirements for this product, describes sampling, methods of test, and packing and marking. Annex A details quatity grades of principal producing countries, while recommendations relating to storage and transport conditions are given in Annex B.</p>"

39054,IS,,ISO 7540:2006,Ground paprika (Capsicum annuum L.) — Specification,Paprika (Capsicum annuum L.) en poudre — Spécifications,2006-10-23,2,['67.220.10'],ISO/TC 34/SC 7,9599,[14322],[70871],"['en','fr','ru']",11,<p>ISO 7540:2006 defines the requirements for ground paprika.</p><p>A method for the determination of the moisture content of ground paprika is given in Annex A. Recommendations relative to storage and transport conditions are given in Annex B. A list of terms used in different countries for paprika (<i>Capsicum annuum </i>L.) is given in Annex C.</p><p>This International Standard is not applicable to ground chillies and capsicums.</p>

14324,IS,,ISO 7541:1989,Ground (powdered) paprika — Determination of total natural colouring matter content,Epices — Paprika en poudre — Détermination de la teneur en matières colorantes naturelles,1989-11-30,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[70872],"['en','fr']",3,"<p>The method consists in extracting of the natural colouring matter content with acetone, measuring of the absorbance of the solution obtained using a spectrometer at a wavelength of 460 nm.</p>"

14331,IS,,ISO 7547:1985,Air-conditioning and ventilation of accommodation spaces on board ships — Design conditions and basis of calculations,Conditionnement d'air et ventilation des emménagements à bord des navires — Conditions de conception et bases de calcul,1985-11-07,1,"['47.020.80','47.020.90']",ISO/TC 8/SC 3,9599,,[27017],"['en','fr']",8,<p>Applies also to the radio cabin on board seagoing merchant ships and to all conditions except those encountered in extremely cold or hot climates.</p>

27017,IS,,ISO 7547:2002,Ships and marine technology — Air-conditioning and ventilation of accommodation spaces — Design conditions and basis of calculations,Navires et technologie maritime — Conditionnement d'air et ventilation des emménagements — Conditions de conception et bases de calcul,2002-09-26,2,"['47.020.80','47.020.90']",ISO/TC 8/SC 3,9599,[14331],[76611],"['en','fr','ru']",13,

52280,IS,Cor,ISO 7547:2002/Cor 1:2008,Ships and marine technology — Air-conditioning and ventilation of accommodation spaces — Design conditions and basis of calculations — Technical Corrigendum 1,Navires et technologie maritime — Conditionnement d'air et ventilation des emménagements — Conditions de conception et bases de calcul — Rectificatif technique 1,2008-09-01,2,"['47.020.80','47.020.90']",ISO/TC 8/SC 3,9599,,[76611],"['en','ru']",2,

14335,IS,,ISO 7551:1996,Dental absorbent points,Cônes absorbants à usage dentaire,1996-12-12,1,['11.060.10'],ISO/TC 106/SC 1,9599,,[80109],"['en','fr']",7,<p>Specifies requirements and test methods for dental absorbent points used in endodontic procedures.</p>

14342,IS,,ISO 7560:1983,Cucumbers — Guide to storage and refrigerated transport,Concombres — Guide pour l'entreposage et le transport réfrigérés,1983-10-01,1,['67.080.20'],ISO/TC 34,9599,,[14343],"['en','fr']",2,

14349,IS,,ISO 7566:1987,Acoustics — Standard reference zero for the calibration of pure-tone bone conduction audiometers,Acoustique — Zéro normal de référence pour l'étalonnage des audiomètres à sons purs en conduction osseuse,1987-04-09,1,['13.140'],ISO/TC 43,9599,,[22495],"['en','fr']",9,

14355,IS,,ISO 7572:1984,Conditions of acceptance and installation for work-holding fixed tables of machine tools,Conditions de réception et d'installation des taques porte-pièces pour machines-outils,1984-05-01,1,['25.060.20'],ISO/TC 39/SC 2,9599,,[27644],"['en','fr']",8,"<p>It also describes with reference to ISO 230, both geometrical tests and the conditions of installation of these fixed tables and gives the corresponding permissible deviation which apply for two classes of accuracy (qualities A and B).</p>"

14356,IS,,ISO 7573:1983,Technical drawings — Item lists,Dessins techniques — Nomenclatures de définition,1983-10-01,1,['01.100.01'],ISO/TC 10/SC 1,9599,,"[33259,26948,43883]","['en','fr']",2,"<p>The guidelines and recommendations given are restricted to item lists as a means for cross-referencing item references (see ISO 6433). Such item lists provide necessary information for the production or procurement of the items and form the basis for establishing other lists for different purposes, as for example time-keeping, stock-taking, etc. Such additional lists should not be included in, nor form part of, end-product drawings.</p>"

14361,IS,,ISO 7575:1984,Road vehicles — Wheels for commercial vehicles — Flat attachment — Fixing nuts,Véhicules routiers — Roues pour véhicules utilitaires — Attache plate — Écrous de fixation,1984-12-01,1,['43.080'],ISO/TC 22,9599,,[14362],"['en','fr']",2,

14363,IS,,ISO 7576:1982,Road vehicles — Heads for two-stage fuel filters for compression ignition engines — Mounting and connecting dimensions,Véhicules routiers — Têtes pour filtres à combustible à deux étages pour moteurs à combustion interne à allumage par compression — Dimensions de montage et de raccordement,1982-11-01,1,['43.060.40'],ISO/TC 22,9599,,[14364],"['en','fr']",2,

14366,IS,,ISO 7578:1982,"Road vehicles — Glow plugs, sheath type — General requirements and test methods",Véhicules routiers — Bougies de préchauffage du type à fourreau — Caractéristiques générales et méthodes d'essai,1982-12-01,1,['43.060.50'],ISO/TC 22,9599,,[14367],"['en','fr']",2,

14367,IS,,ISO 7578:1986,Road vehicles — Sheath-type glow-plugs — General requirements and test methods,Véhicules routiers — Bougies de préchauffage du type à fourreau — Caractéristiques générales et méthodes d'essai,1986-11-27,2,['43.060.50'],ISO/TC 22,9599,[14366],[29434],"['en','fr']",3,

29434,IS,,ISO 7578:2001,Road vehicles — Sheath-type glow-plugs — General requirements and test methods,Véhicules routiers — Bougies de préchauffage du type à fourreau — Exigences générales et méthodes d'essai,2001-05-17,3,['43.060.50'],ISO/TC 22,9599,[14367],[43934],"['en','fr']",5,

43934,IS,,ISO 7578:2008,Road vehicles — Sheath-type glow-plugs — General requirements and test methods,Véhicules routiers — Bougies de préchauffage du type à fourreau — Exigences générales et méthodes d'essai,2008-12-08,4,['43.060.50'],ISO/TC 22/SC 32,9599,[29434],"[59789,59790,63265]",['en'],5,"<p>ISO 7578:2008 specifies general requirements and test methods for sheath-type glow-plugs. Detailed test condition(s) and/or requirement(s) are agreed between the glow-plug manufacturers and the engine manufacturer. It is applicable to those sheath-type glow-plugs conforming to ISO 6550‑1, ISO 6550‑2, ISO 6550‑3 and ISO 6550‑4, used in compression ignition (diesel) engines.</p>"

14368,IS,,ISO 7579:1990,Dyestuffs — Determination of solubility in organic solvents — Gravimetric method,Colorants — Détermination de la solubilité dans les solvants organiques — Méthode gravimétrique,1990-06-14,1,['87.060.10'],ISO/TC 256,9599,,"[45302,26980]","['en','fr']",8,

14370,IS,,ISO 7583:1986,Anodizing of aluminium and its alloys — Vocabulary,Anodisation de l'aluminium et de ses alliages — Vocabulaire,1986-11-20,1,"['25.220.20','01.040.25']",ISO/TC 79/SC 2,9599,,[57434],"['en','fr','ru']",34,"<p>ISO 7583 defines terms concerning anodized aluminium. In addition to terms in the three official ISO languages (English, French and Russian), this International Standard gives the equivalent terms and definitions in the German and Italian languages.</p>"

14375,IS,,ISO 7588:1983,Road vehicles — Relays and flashers — Mounting and positioning dimensions of male tabs and socket apertures for relays and flashers,Véhicules routiers — Relais et centrales clignotantes — Dimensions de montage et de positionnement des languettes et des ouvertures sur le socle pour relais et centrales clignotantes,1983-04-01,1,"['43.040.20','43.040.10']",ISO/TC 22,9599,,"[24778,24782,14376]","['en','fr']",3,

14377,IS,,ISO 7589:1984,Photography — Illuminants for sensitometry — Specifications for daylight and incandescent tungsten,Photographie — Illuminants sensitométriques — Spécifications pour la lumière du jour et la lumière artificielle,1984-10-01,1,['37.040.10'],ISO/TC 42,9599,"[7051,7048,7052]",[33979],"['en','fr']",10,"<p>Specifies the spectral characteristics of illuminants for sensitometry appropriate for evaluating camera films used for pictorial photography in natural daylight, studio tungsten, and photoflood, including both reversal and negative colour and black-and-white films. Describes also a method for evaluating the acceptability of illuminants for sensitometry.</p>"

14378,IS,,ISO 7590:1988,Steel cord conveyor belts — Cover thickness measurement,Courroies transporteuses à câbles d'acier — Mesurage de l'épaisseur des revêtements,1988-08-18,2,['53.040.20'],ISO/TC 41/SC 3,9599,,[14379],"['en','fr']",,

14379,IS,,ISO 7590:1990,Steel cord conveyor belts — Cover thickness measurement,Courroies transporteuses à câbles d'acier — Mesurage de l'épaisseur des revêtements,1990-09-06,3,['53.040.20'],ISO/TC 41/SC 3,9599,[14378],[22090],"['en','fr']",3,

22090,IS,,ISO 7590:2001,Steel cord conveyor belts — Methods for the determination of total thickness and cover thickness,Courroies transporteuses à câbles d'acier — Méthodes de détermination de l'épaisseur totale de la courroie et de l'épaisseur des revêtements,2001-03-22,4,['53.040.20'],ISO/TC 41/SC 3,9599,[14379],[45313],"['en','fr']",6,

45313,IS,,ISO 7590:2009,Steel cord conveyor belts — Methods for the determination of total thickness and cover thickness,Courroies transporteuses à câbles d'acier — Méthodes de détermination de l'épaisseur totale et de l'épaisseur des revêtements,2009-01-05,5,['53.040.20'],ISO/TC 41/SC 3,9599,[22090],[70498],"['en','fr']",7,"<p>ISO 7590:2009 specifies three methods for the measurement of total belt thickness and the thickness of covers of steel cord conveyor belts.</p><p>Methods A1 and A2 (micrometer methods) can be used for all steel cord conveyor belts for the measurement of both total belt thickness and cover thickness.</p><p>Method B (optical method) is recommended for the measurement of

14383,IS,,ISO 7595:1984,Socketing procedures for wire ropes — Molten metal socketing,Procédés de terminaison des câbles métalliques — Manchonnage à l'aide de métal fondu,1984-10-01,1,['77.140.65'],ISO/TC 105,9599,,"[35960,38408,35030]","['en','fr']",6,"<p>Provides guidance on recommended practices for the metal socketing. When socketing ropes which have wire tensile grades greater than 1 960 MPa, special precautions may be necessary and the rope supplier should be consulted. Rope terminations made by ISO 7595 may be used for determining the breaking load of wire ropes in accordance with ISO 3108.</p>"

14385,IS,,ISO 7597:1987,Forged steel lifting hooks with point and eye for use with steel chains of grade T(8),Crochets de levage forgés en acier à bec et à oeil destinés à être utilisés avec des chaînes en acier de classe T(8),1987-04-09,1,['53.020.30'],ISO/TC 111/SC 3,9599,,[57337],"['en','fr']",5,"<p>Specifies requirements for lifting hooks as shown in the figure, in a range of sizes having performance compatibility with the corresponding nominal sizes of grade T(8) chain. Performance compatibility encompasses component strength and the necessary physical dimensions.</p>"

14386,IS,,ISO 7598:1982,Stainless steel tubes suitable for screwing in accordance with ISO 7/1,Tubes en acier inoxydable filetables selon l'ISO 7/1,1982-11-01,1,['23.040.10'],ISO/TC 5/SC 1,9599,,[14387],"['en','fr']",3,

14388,IS,Amd,ISO 7598:1982/Amd 1:1984,Stainless steel tubes suitable for screwing in accordance with ISO 7/1 — Amendment 1,Tubes en acier inoxydable filetables selon l'ISO 7/1 — Amendement 1,1984-04-01,1,['23.040.10'],ISO/TC 5/SC 1,9599,,[14387],['en'],1,

14389,IS,,ISO 7599:1983,Anodizing of aluminium and its alloys — General specifications for anodic oxide coatings on aluminium,Anodisation de l'aluminium et de ses alliages — Spécifications générales pour couches anodiques sur aluminium,1983-09-01,1,['25.220.20'],ISO/TC 79/SC 2,9599,,"[46061,1195,42227]","['en','fr']",7,"<p>These specifications specify the characteristic properties of anodic oxide coatings, methods of test for checking the properties, minimum performance requirements, information on the grades of aluminium suitable for anodizing and the importance of pretreatment. ISO 7599 is applicable to coatings, which are formed on aluminium by an electrolytic oxidation process in which

46061,IS,,ISO 7599:2010,Anodizing of aluminium and its alloys — General specifications for anodic oxidation coatings on aluminium,Anodisation de l'aluminium et de ses alliages — Spécifications générales pour couches anodiques sur aluminium,2010-06-16,2,['25.220.20'],ISO/TC 79/SC 2,9599,[14389],[70156],"['en','fr']",22,"<p>ISO 7599:2010 lays down a method for specifying decorative and protective anodic oxidation coatings on aluminium (including aluminium-based alloys). It defines the characteristic properties of anodic oxidation coatings, lists methods of test for checking the characteristic properties, provides minimum performance requirements, and gives information on the grades of aluminiu

3720,IS,,ISO 76:1978,Rolling bearings — Static load ratings,Roulements — Charges statiques de base,1978-06-01,1,['21.100.20'],ISO/TC 4,9599,,[3721],"['en','fr']",4,

3721,IS,,ISO 76:1987,Rolling bearings — Static load ratings,Roulements — Charges statiques de base,1987-02-05,2,['21.100.20'],ISO/TC 4/SC 8,9599,[3720],[38101],"['en','fr']",5,"<p>This second edition cancels and replaces the first edition (ISO 76 : 1978), of which it constitutes a technical revision. Specifies methods of calculating. Does not apply to designs where the rolling elements operate directly on a shaft or housing surface.</p>"

29762,IS,Amd,ISO 76:1987/Amd 1:1999,Rolling bearings — Static load ratings — Amendment 1: Annex A (informative) — Discontinuities in the calculation of basic static load ratings,Roulements — Charges statiques de base — Amendement 1: Annexe A (informative) — Discontinuités dans le calcul des charges statiquesde base,1999-11-04,2,['21.100.20'],ISO/TC 4/SC 8,9599,,[38101],"['en','fr']",4,

14398,IS,,ISO 7610:1985,Oil of sandalwood — Determination of santalols content (in the form of their trimethylsilyl derivative) — Gas chromatographic method on capillary columns,Huile essentielle de bois de santal — Détermination de la teneur en santalols (sous forme de leur dérivé triméthylsilylé) — Méthode par chromatographie en phase gazeuse sur colonne capillaire,1985-11-14,1,['71.100.60'],ISO/TC 54,9599,,[32037],"['en','fr']",4,<p>A small quantity of the oil is analyzed under specified conditions. The santalols content is determined by using the internal standard method after their transformation into the corresponding trimethylsilyl ethers. Polyethylene glycol 20 000 is used as station

14399,IS,,ISO 7611:1985,"Oils of lemon and petitgrain citronnier, and oil of lime obtained by a mechanical process — Determination of citral (neral + geranial) content — Gas chromatographic method on capillary columns",Huiles essentielles de citron et de petitgrain citronnier et huile essentielle de lime obtenue par des procédés mécaniques — Détermination de la teneur en citral (néral + géranial) — Méthode par chromatographie en phase gazeuse sur colonne capillaire,1985-12-18,1,['71.100.60'],ISO/TC 54,9599,,"[34432,37623,32042]","['en','fr']",5,"<p>The method consists in analyzing a small quantity of essential oil on a column of small diameter but great length under specified conditions. The

14401,IS,,ISO 7612:1983,Base mounted in-line fuel injection pumps,Pompes d'injection en ligne à fixation par base plane,1983-07-01,1,['43.060.40'],ISO/TC 22,9599,,[22736],"['en','fr']",4,

22736,IS,,ISO 7612:1994,Diesel engines — Base-mounted in-line fuel injection pumps — Mounting dimensions,Moteurs diesels — Pompes d'injection en ligne à fixation par base plane — Dimensions de montage,1994-12-22,2,['43.060.40'],ISO/TC 22,9599,[14401],[34824],"['en','fr']",6,<p>Cancels and replaces the first edition (1983). Specifies dimensional requirements for base-mounted in-line fuel injection pumps for diesel (compression-ignition) engines.</p>

34824,IS,,ISO 7612:2006,Diesel engines — Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems — Mounting dimensions,Moteurs diesels — Pompes d'injection en ligne à fixation par base plane et pompes d'alimentation à haute pression pour systèmes d'injection de carburant à rampe commune — Dimensions de montage,2006-01-20,3,['43.060.40'],ISO/TC 22,9599,[22736],[51565],['en'],10,<p>ISO 7612:2005 specifies dimensional requirements for base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems for diesel (compression-ignition) engines.</p>

51565,IS,,ISO 7612:2009,Diesel engines — Base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems — Mounting dimensions,Moteurs diesels — Pompes d'injection en ligne à fixation par base plane et pompes d'alimentation à haute pression pour systèmes d'injection de carburant à rampe commune — Dimensions de montage,2009-10-05,4,['43.060.40'],ISO/TC 22/SC 34,9599,[34824],[75805],['en'],9,<p>ISO 7612:2009 specifies dimensional requirements for base-mounted in-line fuel injection pumps and high-pressure supply pumps for common rail fuel injection systems for diesel (compression-ignition) engines.</p>

14407,IS,,ISO 7617-1:1988,Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics,Supports textiles revêtus de plastique pour ameublement et garniture — Partie 1: Spécifications des étoffes tricotées revêtues de PVC,1988-07-21,1,"['83.140','97.140']",ISO/TC 45,9599,,[22508],"['en','fr']",10,

22508,IS,,ISO 7617-1:1994,Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics,Supports textiles revêtus de plastique pour ameublement et garniture — Partie 1: Spécifications des étoffes tricotées revêtues de PVC,1994-10-13,2,"['97.140','59.080.40']",ISO/TC 45/SC 4,9599,[14407],[23794],"['en','fr']",13,"<p>Cancels and replaces the first edition (1988). Specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a single jersey weft-knitted base cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride.</p

23794,IS,,ISO 7617-1:2001,Plastics-coated fabrics for upholstery — Part 1: Specification for PVC-coated knitted fabrics,Supports textiles revêtus de plastique pour ameublement et garniture — Partie 1: Spécifications des étoffes tricotées revêtues de PVC,2001-12-20,3,"['97.140','59.080.40']",ISO/TC 45/SC 4,9599,[22508],[84079],['en'],17,"<p>This part of ISO 7617 specifies technical requirements for coated fabrics for upholstered furniture for interior use,</p><p>obtained by applying to one side of a weft-knitted base cloth a substantially continuous coating of a suitably</p><p>plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings

14408,IS,,ISO 7617-2:1988,Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics,Supports textiles revêtus de plastique pour ameublement et garniture — Partie 2: Spécifications des tissus revêtus de PVC,1988-06-16,1,"['83.140','97.140']",ISO/TC 45,9599,,[22509],"['en','fr']",6,

22509,IS,,ISO 7617-2:1994,Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics,Supports textiles revêtus de plastique pour ameublement et garniture — Partie 2: Spécifications des tissus revêtus de PVC,1994-10-13,2,"['97.140','59.080.40']",ISO/TC 45/SC 4,9599,[14408],[37012],"['en','fr']",7,"<p>Cancels and replaces the first edition (1988). Specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride.</p>"

37012,IS,,ISO 7617-2:2003,Plastics-coated fabrics for upholstery — Part 2: Specification for PVC-coated woven fabrics,Supports textiles revêtus de plastique pour ameublement et garniture — Partie 2: Spécifications pour les tissus revêtus de PVC,2003-08-19,3,"['97.140','59.080.40']",ISO/TC 45/SC 4,9599,[22509],[89291],['en'],8,"<p>ISO 7617-2:2003 specifies requirements for coated fabrics for upholstered furniture, manufactured by applying to one side of a woven cloth a substantially continuous coating of a suitably plasticized polymer of vinyl chloride, or a copolymer the major constituent of which is vinyl chloride. Such coatings are known as poly(vinyl chloride) (PVC) coatings. The present

31078,IS,,ISO 7619-1:2004,"Rubber, vulcanized or thermoplastic — Determination of indentation hardness — Part 1: Durometer method (Shore hardness)",Caoutchouc vulcanisé ou thermoplastique — Détermination de la dureté par pénétration — Partie 1: Méthode au duromètre (dureté Shore),2004-05-28,1,['83.060'],ISO/TC 45/SC 2,9599,[20170],[50756],"['en','fr']",8,"<p>ISO 7619-1:2004 specifies a method for determining the indentation hardness (Shore hardness) of vulcanized or thermoplastic rubber using durometers with the A scale for rubbers in the normal hardness range, the D scale for those in the high hardness range, the AO scale for those in the low hardness range and cellular rubbers, and the AM

44397,IS,Amd,ISO 7619-1:2004/Amd 1:2008,"Rubber, vulcanized or thermoplastic — Determination of indentation hardness — Part 1: Durometer method (Shore hardness) — Amendment 1: Precision data",Caoutchouc vulcanisé ou thermoplastique — Détermination de la dureté par pénétration — Partie 1: Méthode au duromètre (dureté Shore) — Amendement 1: Données de fidélité,2008-07-23,1,['83.060'],ISO/TC 45/SC 2,9599,,[50756],"['en','fr']",4,

50756,IS,,ISO 7619-1:2010,"Rubber, vulcanized or thermoplastic — Determination of indentation hardness — Part 1: Durometer method (Shore hardness)",Caoutchouc vulcanisé ou thermoplastique — Détermination de la dureté par pénétration — Partie 1: Méthode au duromètre (dureté Shore),2010-09-23,2,['83.060'],ISO/TC 45/SC 2,9599,"[31078,44397]",[74969],"['en','fr','ru']",10,<p>ISO 7619-1:2010 specifies a method for determining the indentation hardness (Shore hardness) of vulcanized or thermoplastic rubber by means of durometers using the A scale for rubbers in the normal-hardness range; the D scale for rubbers in the high-hardness range; the AO scale for rubbers in the low-hardness range and for c

14411,IS,,ISO 7619:1986,Rubber — Determination of indentation hardness by means of pocket hardness meters,Caoutchouc — Détermination de la dureté par pénétration au moyen d'un duromètre de poche,1986-08-14,1,['83.060'],ISO/TC 45/SC 2,9599,,[20170],"['en','fr']",4,

20170,IS,,ISO 7619:1997,Rubber — Determination of indentation hardness by means of pocket hardness meters,Caoutchouc — Détermination de la dureté par pénétration au moyen d'un duromètre de poche,1997-04-10,2,['83.060'],ISO/TC 45/SC 2,9599,[14411],"[31078,37309]","['en','fr']",9,

37309,IS,,ISO 7619-2:2004,"Rubber, vulcanized or thermoplastic — Determination of indentation hardness — Part 2: IRHD pocket meter method",Caoutchouc vulcanisé ou thermoplastique — Détermination de la dureté par pénétration — Partie 2: Méthode au duromètre de poche étalonné en DIDC,2004-05-27,1,['83.060'],ISO/TC 45/SC 2,9599,[20170],[50757],"['en','fr']",5,<p>ISO 7619-2:2004 specifies a method for determining the indentation hardness of vulcanized or thermoplastic rubber by means of a pocket hardness meter calibrated in IRHD.</p>

50757,IS,,ISO 7619-2:2010,"Rubber, vulcanized or thermoplastic — Determination of indentation hardness — Part 2: IRHD pocket meter method",Caoutchouc vulcanisé ou thermoplastique — Détermination de la dureté par pénétration — Partie 2: Méthode au duromètre de poche étalonné en DIDC,2010-09-23,2,['83.060'],ISO/TC 45/SC 2,9599,[37309],[74970],"['en','fr','ru']",5,"<p>ISO 7619-2:2010 specifies a method for determining the indentation hardness of vulcanized or thermoplastic rubber by means of a pocket hardness meter calibrated in IRHD. The use of such meters is primarily intended for control, not specification, purposes.</p>"

5039,IS,,ISO 762:1982,Fruit and vegetable products — Determination of mineral impurities content,Produits dérivés des fruits et légumes — Détermination de la teneur en impuretés minérales d'origine terreuse,1982-02-01,1,['67.080.01'],ISO/TC 34/SC 3,9599,,"[29785,35850]","['en','fr']",2,"<p>The method consists in separating of organic matter by flotation and of heavy impurities by sedimentation, incineration of the sediment at approximately 600 °C, and weihing of the residue obtained. It cancels and replaces ISO Recommendation R 762-1968, of which it constitutes a technical revision.</p>"

14414,IS,,ISO 7622-1:1984,Steel cord conveyor belts — Longitudinal traction test — Part 1: Measurement of elongation,Courroies transporteuses à câbles d'acier — Essai de traction dans le sens longitudinal — Partie 1: Mesurage de l'allongement,1984-12-01,1,['53.040.20'],ISO/TC 41/SC 3,9599,,[61036],"['en','fr']",2,"<p>This part specifies a method for the determination of the elongation of steel cords constituting the carcase of conveyor belts, when subjected to a force corresponding to 10 % and to 60 % of the specified tensile strength. Applies exclusively to conveyor belts with a steel carcase.</p>"

14415,IS,,ISO 7622-2:1984,Steel cord conveyor belts — Longitudinal traction test — Part 2: Measurement of tensile strength,Courroies transporteuses à câbles d'acier — Essai de traction dans le sens longitudinal — Partie 2: Mesurage de la résistance à la rupture,1984-12-01,1,['53.040.20'],ISO/TC 41/SC 3,9599,,[61037],"['en','fr']",3,"<p>This part specifies a method for the determination of the tensile strength, in the longitudinal direction, of conveyor belts with a steel carcase. Some figures illustrate shapes and reference quantities of concern. Applies exclusively to conveyor belts with a steel carcase.</p>"

61037,IS,,ISO 7622-2:2015,Steel cord conveyor belts — Longitudinal traction test — Part 2: Measurement of tensile strength,Courroies transporteuses à câbles d'acier — Essai de traction dans le sens longitudinal — Partie 2: Mesurage de la résistance à la rupture,2015-10-26,2,['53.040.20'],ISO/TC 41/SC 3,9599,[14415],[84317],"['en','fr']",5,"<p>ISO 7622-2:2015 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.</p><p>It applies exclusively to conveyor belts with a steel carcass.</p><p>NOTE A method for the determination of elongation is specified in ISO 7622‑1.</p>"

14416,IS,,ISO 7623:1984,Steel cord conveyor belts — Cord-to-coating bond test,Courroies transporteuses à câbles d'acier — Essai d'adhérence des câbles dans l'enrobage,1984-12-01,1,['53.040.20'],ISO/TC 41/SC 3,9599,,[14417],"['en','fr']",2,

14417,IS,,ISO 7623:1996,Steel cord conveyor belts — Cord-to-coating bond test — Initial test and after thermal treatment,Courroies transporteuses à câbles d'acier — Adhérence des câbles dans l'enrobage — Essais à l'état original et après traitement thermique,1996-05-23,2,['53.040.20'],ISO/TC 41/SC 3,9599,[14416],[65573],"['en','fr']",3,"<p>Provides a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment. Replaces the first edition.</p>"

65573,IS,,ISO 7623:2015,Steel cord conveyor belts — Cord-to-coating bond test — Initial test and after thermal treatment,Courroies transporteuses à câbles d'acier — Adhérence des câbles dans l'enrobage — Essais à l'état original et après traitement thermique,2015-10-09,3,['53.040.20'],ISO/TC 41/SC 3,9599,[14417],[84328],"['en','fr']",5,"<p>ISO 7623:2015 specifies a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment.</p><p>It applies exclusively to metal-carcass conveyor belts.</p>"

14419,IS,,ISO 7625:1983,"Sintered metal materials, excluding hardmetals — Preparation of samples for chemical analysis for determination of carbon content","Matériaux métalliques frittés, à l'exclusion des métaux-durs — Préparation des échantillons pour analyse en vue du dosage du carbone",1983-10-01,1,['77.160'],ISO/TC 119/SC 3,9599,,[33550],"['en','fr']",2,"<p>Applies to the chemical determination of free or total carbon content in parts in which carbon is uniformly distributed and present in the forms shown in table 1. Combined carbon is determined as the difference between total and free carbon. The presence of carbonaceous materials in the pores or on the surface interferes with the det

33550,IS,,ISO 7625:2006,"Sintered metal materials, excluding hardmetals — Preparation of samples for chemical analysis for determination of carbon content","Matériaux métalliques frittés, à l'exclusion des métaux-durs — Préparation des échantillons pour analyse chimique en vue du dosage du carbone",2006-09-11,2,['77.160'],ISO/TC 119/SC 3,9599,[14419],[57412],"['en','fr']",3,"<p>ISO 7625:2006 specifies methods for preparing a sample from one or more sintered parts of materials to be analysed for free or total carbon content. Combined carbon is determined as the difference between total and free carbon. This standard covers the preparation of samples for the determination of carbon by a chemic

14420,IS,,ISO 7626-1:1986,Vibration and shock — Experimental determination of mechanical mobility — Part 1: Basic definitions and transducers,Vibrations et chocs — Détermination expérimentale de la mobilité mécanique — Partie 1: Définitions fondamentales et transducteurs,1986-08-28,1,['17.160'],ISO/TC 108,9599,,"[30106,50426]","['en','fr']",23,"<p>Provides basic concepts with comments and identifies the calibration tests, environmental tests and physical measurements necessary to determine the suitability of impedance heads, force transducers and response transducers. Is limited to information which is basic to various types of driving point and transfer mobility, accelerance and dynamic com

14421,IS,,ISO 7626-2:1990,Vibration and shock — Experimental determination of mechanical mobility — Part 2: Measurements using single-point translation excitation with an attached vibration exciter,"Vibrations et chocs — Détermination expérimentale de la mobilité mécanique — Partie 2: Mesurages avec utilisation d'une excitation de translation en un seul point, au moyen d'un générateur de vibrations solidaire de ce point",1990-02-08,1,['17.160'],ISO/TC 108,9599,,"[24138,62483]","['en','fr']",21,"<p>Specifies procedures for measuring the quantity and other frequency-response functions of structures, such as buildings, machines and vehicles. Is applicable to measurements of mobility, acceleranc

14424,IS,,ISO 7626-5:1994,Vibration and shock — Experimental determination of mechanical mobility — Part 5: Measurements using impact excitation with an exciter which is not attached to the structure,Vibrations et chocs — Détermination expérimentale de la mobilité mécanique — Partie 5: Mesurages à partir d'une excitation par choc appliquée par un excitateur non solidaire de la structure,1994-06-30,1,['17.160'],ISO/TC 108,9599,,[68735],"['en','fr']",22,"<p>Specifies procedures for measuring mechanical mobility and other frequency-response functions of structures excited by means of a translational impulsive force generated by an exciter which is not attached to the structure under test. Is ap

14433,IS,,ISO 7628-1:1985,Road vehicles — Thermoplastic tubing for use in air braking systems — Part 1: Dimensions and marking,Véhicules routiers — Tuyauteries thermoplastiques pour freinage pneumatique — Partie 1: Dimensions et marquage,1985-03-21,1,"['43.040.40','83.140.30']",ISO/TC 22,9599,,[14434],"['en','fr']",1,

14434,IS,,ISO 7628-1:1998,Road vehicles — Thermoplastics tubing for air braking systems — Part 1: Dimensions and marking,Véhicules routiers — Tuyauteries thermoplastiques pour dispositifs de freinage pneumatique — Partie 1: Dimensions et marquage,1998-08-20,2,"['43.040.40','83.140.30']",ISO/TC 22,9599,[14433],[50497],"['en','fr']",2,

14436,IS,,ISO 7628-2:1998,Road vehicles — Thermoplastics tubing for air braking systems — Part 2: Mounting on vehicle and test methods,Véhicules routiers — Tuyauteries thermoplastiques pour dispositifs de freinage pneumatique — Partie 2: Conditions de montage sur le véhicule et méthodes d'essai,1998-08-20,1,"['43.040.40','83.140.30']",ISO/TC 22,9599,[14435],[50497],"['en','fr']",25,

31314,IS,Cor,ISO 7628-2:1998/Cor 1:1999,Road vehicles — Thermoplastics tubing for air braking systems — Part 2: Mounting on vehicle and test methods — Technical Corrigendum 1,Véhicules routiers — Tuyauteries thermoplastiques pour dispositifs de freinage pneumatique — Partie 2: Conditions de montage sur le véhicule et méthodes d'essai — Rectificatif technique 1,1999-03-04,1,"['43.040.40','83.140.30']",ISO/TC 22,9599,,[50497],"['en','fr']",2,

5040,IS,,ISO 763:1982,Fruit and vegetable products — Determination of ash insoluble in hydrochloric acid,Produits dérivés des fruits et légumes — Détermination des cendres insolubles dans l'acide chlorhydrique,1982-03-01,1,['67.080.01'],ISO/TC 34/SC 3,9599,,"[37150,21495]","['en','fr']",2,"<p>The method serves for the determination of siliceous impurities, together with the silica endogenous to the plant. It cancels and replaces ISO Recommendation R 763-1971, of which it constitutes a technical revision. It consists in incinerating of a test portion at 525 °C, and separating of the mineral matter insoluble in dilute hydrochloric acid solution. The method for the determination of mineral impu

14442,IS,,ISO 7634:1995,Towed road vehicles — Compressed-air braking systems — Measurement of braking performance,Véhicules routiers remorqués — Dispositifs de freinage à air comprimé — Mesurage des performances de freinage,1995-04-20,1,['43.040.40'],ISO/TC 22,9599,,[27127],"['en','fr']",30,"<p>Specifies a uniform test method for braking systems of full trailers, semi-trailers and centre-axle trailers with compressed-air braking systems, pending the harmonization of national and international braking standards, regulations and directives. The brake test procedure specified herein applies to these trailers corresponding to vehicle category 0 in UN-ECE Regulation No. 13.</p>"

27127,IS,,ISO 7634:2003,Road vehicles — Compressed-air braking systems — Test procedures,Véhicules routiers — Dispositifs de freinage à air comprimé — Modes opératoires d'essai,2003-05-20,2,['43.040.40'],ISO/TC 22,9599,[14442],"[44051,36968]",['en'],45,"<p>ISO 7634:2003 specifies procedures for testing the compressed-air braking systems of full trailers, semi-trailers and centre-axle trailers, with and without antilock braking system (ABS), corresponding to road vehicles of Category O as defined in UNECE R.E. 3. </p>"

14443,IS,,ISO 7635:1991,Road vehicles — Air or air over hydraulic braking systems — Measurement of braking performance,Véhicules routiers — Dispositifs de freinage à transmission pneumatique ou hydropneumatique — Mesurage des performances de freinage,1991-10-10,1,['43.040.40'],ISO/TC 22,9599,,[27125],"['en','fr']",18,<p>Specifies the test method for braking systems of vehicles of categories M and N according to UN-ECE Regulation No. 13. Annex A forms an integral part of this standard.</p>

27125,IS,,ISO 7635:2003,Road vehicles — Air or air-over hydraulic braking systems for motor vehicles (including those with electronic control functions) — Test procedures,Véhicules routiers — Dispositifs de freinage à air comprimé ou hydropneumatiques pour automobiles (y compris ceux à fonctions de commande électronique) — Mode opératoire d'essai,2003-11-07,2,['43.040.40'],ISO/TC 22,9599,[14443],[36970],['en'],35,<p>ISO 7635:2003 specifies procedures for testing the air or air-over hydraulic braking systems of vehicles of categories M and N (excluding M₁ and N₁) as defined in UNECE R.E.3. </p>

14446,IS,,ISO 7637-0:1990,Road vehicles — Electrical disturbance by conduction and coupling — Part 0: Definitions and general,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 0: Définitions et généralités,1990-08-09,1,"['43.040.10','01.040.43']",ISO/TC 22,9599,[14445],[28534],"['en','fr']",2,

14448,IS,,ISO 7637-1:1990,Road vehicles — Electrical disturbance by conduction and coupling — Part 1: Passenger cars and light commercial vehicles with nominal 12 V supply voltage — Electrical transient conduction along supply lines only,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 1: Voitures particulières et véhicules utilitaires légers à tension nominale de 12 V — Transmission des perturbations électriques par conduction uniquement le long des lignes d'alimentation,1990-06-07,1,['43.040.10'],ISO/TC 22,9599,[14447],[28533],"['en','fr']",13,

28534,IS,,ISO 7637-1:2002,Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 1: Définitions et généralités,2002-03-21,2,"['43.040.10','01.040.43']",ISO/TC 22/SC 32,9599,[14446],[63098],"['en','fr']",6,"<p>This part of ISO 7637 defines the basic terms relating to electrical disturbances from conduction and coupling used in its other parts, and gives general information on the whole of ISO 7637 and common to all parts.</p>"

45930,IS,Amd,ISO 7637-1:2002/Amd 1:2008,Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations — Amendment 1,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 1: Définitions et généralités — Amendement 1,2008-01-22,2,"['43.040.10','01.040.43']",ISO/TC 22/SC 32,9599,,[63098],"['en','fr']",4,

63098,IS,,ISO 7637-1:2015,Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 1: Définitions et généralités,2015-10-20,3,"['43.040.10','01.040.43']",ISO/TC 22/SC 32,9599,"[45930,28534]",[83230],['en'],10,<p>ISO 7637-1:2015 defines the basic terms relating to electrical disturbances from conduction and coupling used in the other parts of ISO 7637. It also gives general information on the whole ISO 7637 series.</p>

14449,IS,,ISO 7637-2:1990,Road vehicles — Electrical disturbance by conduction and coupling — Part 2: Commercial vehicles with nominal 24 V supply voltage — Electrical transient conduction along supply lines only,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 2: Véhicules utilitaires à tension nominale de 24 V — Transmission des perturbations électriques par conduction uniquement le long des lignes d'alimentation,1990-06-07,1,['43.040.10'],ISO/TC 22,9599,,[28533],"['en','fr']",12,

28533,IS,,ISO 7637-2:2004,Road vehicles — Electrical disturbances from conduction and coupling — Part 2: Electrical transient conduction along supply lines only,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 2: Transmission des perturbations électriques transitoires par conduction uniquement le long des lignes d'alimentation,2004-06-28,2,['43.040.10'],ISO/TC 22,9599,"[14448,14449]",[50925],"['en','fr']",36,"<p>ISO 7637-2:2004 specifies bench tests for testing the compatibility to conducted electrical transients of equipment installed on passenger cars and light commercial vehicles fitted with a 12 V electrical system or commercial vehicles fitted with

45931,IS,Amd,ISO 7637-2:2004/Amd 1:2008,Road vehicles — Electrical disturbances from conduction and coupling — Part 2: Electrical transient conduction along supply lines only — Amendment 1,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 2: Transmission des perturbations électriques transitoires par conduction uniquement le long des lignes d'alimentation — Amendement 1,2008-01-22,2,['43.040.10'],ISO/TC 22,9599,,[50925],"['en','fr']",3,

14450,IS,,ISO 7637-3:1995,Road vehicles — Electrical disturbance by conduction and coupling — Part 3: Vehicles with nominal 12 V or 24 V supply voltage — Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 3: Véhicules à tension nominale de 12 V ou 24 V — Transmission des perturbations électriques par couplage capacitif ou inductif le long des lignes autres que les lignes d'alimentation,1995-07-20,1,['43.040.10'],ISO/TC 22,9599,,[40581],"['en','fr']",10,"<p>Establishes a basis for the evaluation of the EMC of electronic instruments, devices and equipment

26421,IS,Cor,ISO 7637-3:1995/Cor 1:1995,Road vehicles — Electrical disturbance by conduction and coupling — Part 3: Vehicles with nominal 12 V or 24 V supply voltage — Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines — Technical Corrigendum 1,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 3: Véhicules à tension nominale de 12 V ou 24 V — Transmission des perturbations électriques par couplage capacitif ou inductif le long des lignes autres que les lignes d'alimentation — Rectificatif technique 1,1995-11-02,1,['43.040.10'],ISO/TC 22,9599,,[40581],"['en','fr']",1,<p>Replaces existing tables A.1 and

40581,IS,,ISO 7637-3:2007,Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 3: Transmission des perturbations électriques par couplage capacitif ou inductif le long des lignes autres que les lignes d'alimentation,2007-07-03,2,['43.040.10'],ISO/TC 22/SC 32,9599,"[26421,14450]",[59603],"['en','fr']",24,"<p>ISO 7637-3:2007 establishes a bench top test for the evaluation of the immunity of devices under test (DUTs) to transient transmission by coupling via lines other than suppl

21340,IS,,ISO 7638-1:1997,Road vehicles — Electrical connectors for braking systems — Part 1: Connectors for 24 V nominal supply voltage,Véhicules routiers — Connecteurs électriques pour dispositifs de freinage — Partie 1: Connecteurs pour systèmes à tension nominale de 24 V,1997-10-02,1,"['43.040.10','43.040.40']",ISO/TC 22,9599,[14453],[30209],"['en','fr']",12,

30374,IS,Cor,ISO 7638-1:1997/Cor 1:1998,Road vehicles — Electrical connectors for braking systems — Part 1: Connectors for 24 V nominal supply voltage — Technical Corrigendum 1,Véhicules routiers — Connecteurs électriques pour dispositifs de freinage — Partie 1: Connecteurs pour systèmes à tension nominale de 24 V — Rectificatif technique 1,1998-05-07,1,"['43.040.10','43.040.40']",ISO/TC 22,9599,,[30209],"['en','fr']",1,

30209,IS,,ISO 7638-1:2003,Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Part 1: Connectors for braking systems and running gear of vehicles with 24 V nominal supply voltage,Véhicules routiers — Connecteurs pour liaisons électriques entre véhicules tracteurs et véhicules tractés — Partie 1: Connecteurs pour les équipements de freinage et les organes de roulement des véhicules à tension nominale de 24 V,2003-11-14,2,"['43.040.10','43.040.40']",ISO/TC 22/SC 32,9599,"[30374,21340]",[70639],"['en','fr']",9,"<p>ISO 7638-1:2003 gives the dimensions of, and specifies the contact allocation and tests and test requirements for, connectors for the electrical co

14453,IS,,ISO 7638:1985,Road vehicles — Brake anti-lock device connector,Véhicules routiers — Prise pour dispositif d'antiblocage du frein,1985-02-07,1,"['43.040.10','43.040.40']",ISO/TC 22,9599,,"[25682,21340]","['en','fr']",11,

25682,IS,,ISO 7638-2:1997,Road vehicles — Electrical connectors for braking systems — Part 2: Connectors for 12 V nominal supply voltage,Véhicules routiers — Connecteurs électriques pour dispositifs de freinage — Partie 2: Connecteurs pour systèmes à tension nominale de 12 V,1997-10-02,1,"['43.040.10','43.040.40']",ISO/TC 22,9599,[14453],[30208],"['en','fr']",12,

30375,IS,Cor,ISO 7638-2:1997/Cor 1:1998,Road vehicles — Electrical connectors for braking systems — Part 2: Connectors for 12 V nominal supply voltage — Technical Corrigendum 1,Véhicules routiers — Connecteurs électriques pour dispositifs de freinage — Partie 2: Connecteurs pour systèmes à tension nominale de 12 V — Rectificatif technique 1,1998-05-07,1,"['43.040.10','43.040.40']",ISO/TC 22,9599,,[30208],"['en','fr']",1,

30208,IS,,ISO 7638-2:2003,Road vehicles — Connectors for the electrical connection of towing and towed vehicles — Part 2: Connectors for braking systems and running gear of vehicles with 12 V nominal supply voltage,Véhicules routiers — Connecteurs pour liaisons électriques entre véhicules tracteurs et véhicules tractés — Partie 2: Connecteurs pour les équipements de freinage et les organes de roulement des véhicules à tension nominale de 12 V,2003-11-14,2,"['43.040.10','43.040.40']",ISO/TC 22/SC 32,9599,"[25682,30375]",[70640],"['en','fr']",9,"<p>ISO 7638-2:2003 gives the dimensions of, and specifies the contact allocation and tests and test requirements for, connectors for the electrical co

5041,IS,,ISO 764:1973,'Antimagnetic' watches for general purpose use,Montres 'antimagnétiques' pour usage courant,1973-07-01,1,['39.040.10'],ISO/TC 114,9599,,[5042],"['en','fr']",1,

5042,IS,,ISO 764:1984,Horology — Antimagnetic watches,Horlogerie — Montres antimagnétiques,1984-04-01,2,['39.040.10'],ISO/TC 114/SC 12,9599,[5041],[23033],"['en','fr']",2,<p>Specifies the minimum requirements and describes the corresponding method of test. It based on the simulation of the accidental exposure of a watch to a macnetic field of 4800 A/m.</p>

23033,IS,,ISO 764:2002,Horology — Magnetic resistant watches,Horlogerie — Montres antimagnétiques,2002-07-18,3,['39.040.10'],ISO/TC 114/SC 12,9599,[5042],[70610],"['en','fr']",5,<p>ISO 764 specifies the minimum requirements and test methods for magnetic resistant watches.</p><p>It is based on the simulation of an accidental exposure of a watch to a direct current magnetic field of 4 800 A/m.</p><p>Annex A deals with watches designated as magnetic resistant with an additional indication of intensity of a magnetic field exceeding 4 800 A/m.</p>

14456,IS,,ISO 7641-1:1983,Road vehicles — Caravans and light trailers — Calculation of the mechanical strength of the drawbar — Part 1: Steel drawbars,Véhicules routiers — Caravanes et remorques légères — Calcul de résistance des timons — Partie 1: Cas des timons en acier,1983-10-01,1,['43.040.70'],ISO/TC 22,9599,,"[51861,40332,26743,21122]","['en','fr']",3,<p>Gives a simplified procedure for the calculation of the mechanical strength of drawbars where the vertical static load on the coupling head does not exceed the limits specified in ISO/TR 4114. Applies only to steel drawbars of welded and other than welded construction. The welding procedure requirements given by the manufacturer shall

14457,IS,,ISO 7642:1983,Road vehicles — Caravans and light trailers — Trailers of categories 01 and 02 — Inertia bench test procedures for overrun brakes,Véhicules routiers — Caravanes et remorques légères — Remorques des catégories 01 et 02 freinées par inertie — Procédures d'essai de frein sur banc à masse d'inertie,1983-04-01,1,['43.040.40'],ISO/TC 22,9599,,[14458],"['en','fr']",4,

14459,IS,,ISO 7643:1983,Road vehicles — Caravans and light trailers — Bench test methods for brake controls for inertia braked trailers of categories 01 and 02,Véhicules routiers — Caravanes et remorques légères — Méthodes d'essai au banc des dispositifs de commande de freinage pour remorques de catégories 01 et 02 freinées par inertie,1983-12-01,1,['43.040.40'],ISO/TC 22,9599,,[14460],"['en','fr']",4,

5043,IS,,ISO 765:1976,Pesticides considered not to require common names,Pesticides considérés comme ne nécessitant pas de nom commun,1976-12-01,1,['65.100.01'],ISO/TC 81,9599,[5622],"[57854,5044]","['en','fr','ru']",13,"<p>Gives a list of certain pesticide chemicals with reasonably short and distinctive chemical names or trivial name already known, to which it is deemed unnecessary to assign recommended common names at present. This standard is a trilingual edition (Englisch-French-Russian).</p>"