Withdrawn and superseded ISO standards — page 159 of 246

14180,IS,,ISO 7441:1984,Corrosion of metals and alloys — Determination of bimetallic corrosion in outdoor exposure corrosion tests,Corrosion des métaux et alliages — Détermination de la corrosion bimétallique par des essais de corrosion en milieu extérieur,1984-12-01,1,['77.060'],ISO/TC 156,9599,,[53633],"['en','fr']",12,"<p>Applies to metals and alloys, and metals and alloys with metallic and non-metallic non-organic coatings. The methods are intended for the determination of the amount and type of corrosion effect, arising in natural atmospheres, caused by contact with different metals (coated metals), and for the evaluation of the effectiveness of bimetallic corrosion protection treatment

14181,IS,,ISO 7442:1982,Tyre valves — ISO core chamber No. 1,Valves pour pneumatiques — Logement du mécanisme ISO no 1,1982-10-01,1,['83.160.01'],ISO/TC 31/SC 9,9599,,[34212],"['en','fr']",4,"<p>Specifies the interchangeability dimensions of an core chamber, and applies principally to core chambers of valves used on tyres for agricultural machines, earth-moving machines, road vehicles and civil aircraft. Figure 1 shows the details the core chamber. Figure 2 gives the tolerances for the core pin head position. An annex gives counterbore dimensions.</p>"

14186,IS,,ISO 7451:1983,Earth-moving machinery — Hydraulic excavators — Hoe type buckets — Volumetric ratings,Engins de terrassement — Godets de pelles hydrauliques travaillant en rétro — Évaluations volumétriques,1983-06-01,1,['53.100'],ISO/TC 127/SC 1,9599,,[1827],"['en','fr']",5,

1827,IS,,ISO 7451:1997,Earth-moving machinery — Volumetric ratings for hydraulic excavator buckets and backhoe loader buckets,Engins de terrassement — Évaluations volumétriques des godets de pelles hydrauliques travaillant en rétro,1997-07-03,2,['53.100'],ISO/TC 127/SC 1,9599,[14186],[39808],"['en','fr']",8,

29964,IS,Cor,ISO 7451:1997/Cor 1:1998,Earth-moving machinery — Volumetric ratings for hydraulic excavator buckets and backhoe loader buckets — Technical Corrigendum 1,Engins de terrassement — Évaluations volumétriques des godets de pelles hydrauliques travaillant en rétro — Rectificatif technique 1,1998-02-19,2,['53.100'],ISO/TC 127/SC 1,9599,,[39808],"['en','fr']",1,

14187,IS,,ISO 7452:1984,Hot-rolled structural steel plates — Tolerances on dimensions and shape,Tôles en acier de construction laminées à chaud — Tolérances sur dimensions et forme,1984-12-01,1,['77.140.50'],ISO/TC 17/SC 3,9599,,"[36900,25859]","['en','fr']",5,"<p>Applies to hot-rolled, non-alloyed, alloyed and stainless steel plates of nominal thickness up to 150 mm and of width up to 4 000 mm whose specified minimum yield stress is equal to or less than 700 N/mm . Does not include round plate, custom-made plate, checker plate or bulb plate for flooring or wide flats.</p>"

36900,IS,,ISO 7452:2002,Hot-rolled structural steel plates — Tolerances on dimensions and shape,Tôles en acier de construction laminées à chaud — Tolérances sur les dimensions et la forme,2002-10-22,2,"['77.140.70','77.140.50']",ISO/TC 17/SC 3,9599,[14187],[54403],"['en','fr']",14,<p>ISO 7452:2002 specifies requirements for tolerances for hot-rolled steel plates made on a reversing mill (excluding stainless steels) with the following characteristics:</p><ol><li>nominal thickness not less than 4 mm but no greater than 400 mm;</li><li>nominal width not less than 600 mm;</li><li>specified minimum yield strength not less than 700 N/mm².</li></ol>

14192,IS,,ISO 7457:1983,Earth-moving machinery — Measurement of turning dimensions of wheeled machines,Engins de terrassement — Mesurage des dimensions de braquage des engins à roues,1983-08-01,1,['53.100'],ISO/TC 127/SC 1,9599,,[23692],"['en','fr']",7,

14193,IS,,ISO 7458:1984,Glass containers — Internal pressure resistance — Test methods,Récipients en verre — Résistance à la pression interne — Méthodes d'essai,1984-12-01,1,['55.100'],ISO/TC 63,9599,,[35606],"['en','fr']",2,"<p>Two methods are specified for the determination: In method A an uniform internal pressure is used for a predetermined period and in method B an internal pressure increasing at a constant rate will be applied. For both methods the procedure, apparatus and test report, resp., are specified.</p>"

14194,IS,,ISO 7459:1984,Glass containers — Thermal shock resistance and thermal shock endurance — Test methods,Récipients en verre — Résistance au choc thermique et endurance au choc thermique — Méthodes d'essai,1984-12-01,1,['55.100'],ISO/TC 63,9599,,[35615],"['en','fr']",2,"<p>The containers are subjected to a sudden change temperature, i.e. to cold and hot bath, for determing their performance. Apparatus, sampling and procedures are specified. The requirements apply only to containers made of soda-silica glass.</p>"

14198,IS,,ISO 7463:1990,Shipbuilding and marine structures — Symbols for computer applications,Construction navale et structures maritimes — Symboles pour les applications informatiques,1990-09-20,1,"['35.240.50','01.075','47.020.01']",ISO/TC 8/SC 6,9599,,[30919],['en'],29,

14200,IS,,ISO 7465:1983,Passenger lifts and service lifts — Guide rails for lifts and counterweights — T-type,Ascenseurs et monte-charge — Guides de cabine et de contrepoids — Profils en T,1983-02-01,1,['91.140.90'],ISO/TC 178,9599,,[14201],"['en','fr']",9,

14201,IS,,ISO 7465:1997,Passenger lifts and service lifts — Guide rails for lifts and counterweights — T-type,Ascenseurs et monte-charge — Guides de cabine et de contrepoids — Profils en T,1997-09-11,2,['91.140.90'],ISO/TC 178,9599,[14200],[31424],"['en','fr']",14,

31424,IS,,ISO 7465:2001,Passenger lifts and service lifts — Guide rails for lift cars and counterweights — T-type,Ascenseurs et monte-charge — Guides de cabine et de contrepoids — Profils en T,2001-12-06,3,['91.140.90'],ISO/TC 178,9599,[14201],[43008],"['en','fr']",16,

43008,IS,,ISO 7465:2007,Passenger lifts and service lifts — Guide rails for lift cars and counterweights — T-type,Ascenseurs et monte-charges — Guides de cabine et de contrepoids — Profils en T,2007-11-07,4,['91.140.90'],ISO/TC 178,9599,[31424],"[60950,71221]","['en','fr']",16,"<p>ISO 7456:2007 specifies the grades and quality, the dimensional characteristics, the dimensional and geometrical tolerances, and the surface finish of standardized guide rails and their fishplates.</p><p>In addition, ISO 7456:2007 defines a designation system for guide rails.</p><p>ISO 7456:2007 is applicable to guide rails used in passenger lift and service lift installations to provide guiding for the car and the

14213,IS,,ISO 7475:1984,Balancing machines — Enclosures and other safety measures,Machines à équilibrer — Enceintes et autres mesures de sécurité,1984-11-01,1,['21.120.40'],ISO/TC 108,9599,,[25813],"['en','fr']",8,"<p>Specifies requirements used to minimize hazards associated with the operation of these machines under a variety of rotor and balancing conditions. Defines different classes of protection and describes the limits of applicability for each class of protection. Noise reduction, windage reduction or vacuum are not covered.</p>"

33239,IS,Cor,ISO 7475:1984/Cor 1:1999,Balancing machines — Enclosures and other safety measures — Technical Corrigendum 1,Machines à équilibrer — Enceintes et autres mesures de sécurité — Rectificatif technique 1,1999-10-28,1,['21.120.40'],ISO/TC 108,9599,,[25813],"['en','fr']",2,

25813,IS,,ISO 7475:2002,Mechanical vibration — Balancing machines — Enclosures and other protective measures for the measuring station,Vibrations mécaniques — Machines à équilibrer — Enceintes et autres mesures de protection pour le poste de mesurage,2002-03-07,2,['21.120.40'],ISO/TC 108/SC 2,9599,"[33239,14213]",[54075],['en'],23,"<p>This International Standard specifies requirements for enclosures and other protective measures used to minimize mechanical hazards produced by the rotor in the unbalance measuring station of centrifugal (rotational) balancing machines. The hazards are associated with the operation of balancing machines under a variety of rotor and balancing conditions. This In

14214,IS,,ISO 7476:1990,Determination of uranium in uranyl nitrate solutions of nuclear grade quality — Gravimetric method,Détermination de l'uranium dans les solutions de nitrate d'uranyle de qualité nucléaire — Méthode gravimétrique,1990-12-06,1,['27.120.30'],ISO/TC 85/SC 5,9599,,[34544],"['en','fr']",4,"<p>Gives a precise and accurate gravimetric method for determining the uranium content. Non-volatile impurities influence the accuracy of the method. Specifies principle, interferences, reagents, apparatus, procedure, expression of results and test report.</p>"

14219,IS,,ISO 7479:1982,Textile machinery and accessories — Metal reeds with plastic baulk,Matériel pour l'industrie textile — Peignes métalliques avec ligature plastique,1982-12-01,1,['59.120.30'],ISO/TC 72/SC 3,9599,,[4339],"['en','fr']",1,

5002,IS,,ISO 748:1979,Liquid flow measurement in open channels — Velocity-area methods,Mesure de débit des liquides dans les canaux découverts — Méthodes d'exploration du champ des vitesses,1979-04-01,2,['17.120.20'],ISO/TC 113,9599,,[5003],"['en','fr']",23,

5003,IS,,ISO 748:1997,Measurement of liquid flow in open channels — Velocity-area methods,Mesure de débit des liquides dans les canaux découverts — Méthodes d'exploration du champ des vitesses,1997-07-31,3,['17.120.20'],ISO/TC 113/SC 1,9599,[5002],[37573],"['en','fr']",41,

37573,IS,,ISO 748:2007,Hydrometry — Measurement of liquid flow in open channels using current-meters or floats,Hydrométrie — Mesurage du débit des liquides dans les canaux découverts au moyen de moulinets ou de flotteurs,2007-10-11,4,['17.120.20'],ISO/TC 113/SC 1,9599,[5003],[72754],"['en','fr']",46,"<p>ISO 748:2007 specifies methods for determining the velocity and cross‑sectional area of water flowing in open channels without ice cover, and for computing the discharge therefrom.</p><p>ISO 748:2007 covers methods of employing current‑meters or floats to measure the velocities. It deals only with single measurements of the discharge; the continuous recording of discharges over a period of ti

14220,IS,,ISO 7480:1984,Information processing — Start-stop transmission signal quality at DTE/DCE interfaces,Traitement de l'information — Qualité des signaux de transmission arythmique aux interfaces ETTD/ETCD,1984-09-01,1,['35.100.10'],ISO/IEC JTC 1/SC 6,9599,,[14221],"['en','fr']",10,

14222,IS,,ISO 7481:1984,Aerospace — Fasteners — Self-locking nuts with maximum operating temperature less than or equal to 425 degrees C — Test methods,Aéronautique et espace — Éléments de fixation — Écrous à freinage interne dont la température maximale d'utilisation est inférieure ou égale à 425 degrés C — Méthodes de contrôle et d'essai,1984-05-01,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[14223],"['en','fr']",11,

14223,IS,,ISO 7481:2000,"Aerospace — Nuts, self-locking, with maximum operating temperature less than or equal to 425 degrees C — Test methods",Aéronautique et espace — Écrous à freinage interne dont la température maximale d'utilisation est inférieure ou égale à 425 degrés C — Méthodes de contrôle et d'essai,2000-02-03,2,['49.030.30'],ISO/TC 20/SC 4,9599,[14222],"[68577,84018]","['en','fr']",19,"<p>This International Standard specifies test methods for metric self-locking nuts with MJ threads intended for use in</p><p>aerospace construction at maximum operating temperatures less than or equal to 425 °C. It describes the test</p><p>device and the method for each test.</p><p>It applies to sel

14234,IS,,ISO 7487-1:1985,"Information processing — Data interchange on 130 mm (5.25 in) flexible disk cartridges using modified frequency modulation recording at 7 958 ftprad, 1,9 tpmm (48 tpi), on both sides — Part 1: Dimensional, physical and magnetic characteristics","Traitement de l'information — Échange de données sur cartouches à disquette de 130 mm (5,25 in) utilisant un enregistrement à modulation de fréquence modifiée à 7 958 ftprad, 1,9 tpmm (48 tpi), sur deux faces — Partie 1: Caractéristiques dimensionnelles, physiques et magnétiques",1985-03-21,1,['35.220.20'],ISO/IEC JTC 1,9599,,[20896],"['en','fr']",16,

14236,IS,,ISO 7487-3:1984,"Information processing — Data interchange on 130 mm (5.25 in) flexible disk cartridges using modified frequency modulation recording at 7 958 ftprad, 1,9 tpmm (48 tpi), on two sides — Part 3: Track format B","Traitement de l'information — Échange de données sur cartouches à disquette de 130 mm (5,25 in) utilisant un enregistrement à modulation de fréquence modifiée à 7 958 ftprad, 1,9 tpmm (48 tpi), sur deux faces — Partie 3: Schéma de piste B",1984-11-01,1,['35.220.21'],ISO/IEC JTC 1,9599,,[14237],"['en','fr']",10,

14239,IS,,ISO 7488:1991,Dental amalgamators,Amalgamateurs dentaires,1991-05-30,1,['11.060.20'],ISO/TC 106/SC 6,9599,,[68818],"['en','fr']",4,

14240,IS,,ISO 7489:1986,Dental glass polyalkenoate cements,Ciments dentaires au polyalkénoate de verre,1986-05-15,1,['11.060.10'],ISO/TC 106/SC 1,9599,,[17800],"['en','fr']",10,

14241,IS,,ISO 7490:1990,Dental gypsum-bonded casting investments for gold alloys,Revêtements à couler à liant-plâtre dentaire pour les alliages d'or,1990-06-14,1,['11.060.10'],ISO/TC 106/SC 2,9599,,[24011],"['en','fr']",16,

24011,IS,,ISO 7490:2000,Dental gypsum-bonded casting investments,Revêtements à couler dentaires à liant-plâtre,2000-12-20,2,['11.060.10'],ISO/TC 106/SC 2,9599,[14241],[37646],"['en','fr']",9,

14242,IS,,ISO 7491:1985,Dental materials — Determination of colour stability of dental polymeric materials,Produits dentaires — Détermination de la stabilité de couleur des produits dentaires à base de polymères,1985-08-15,1,['11.060.10'],ISO/TC 106/SC 2,9599,,[26857],"['en','fr']",2,

14243,IS,,ISO 7492:1983,Dental explorers,Sondes exploratrices dentaires,1983-12-01,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[14244],"['en','fr']",3,

14244,IS,,ISO 7492:1997,Dental explorers,Sondes exploratrices dentaires,1997-02-13,2,['11.060.20'],ISO/TC 106/SC 4,9599,[14243],[66689],"['en','fr']",15,<p>Specifies the dimensions and performance requirements for dental explorers. Replaces the first edition.</p>

66689,IS,,ISO 7492:2018,Dentistry — Dental explorer,Médecine bucco-dentaire — Sondes exploratrices dentaires,2018-02-01,3,['11.060.20'],ISO/TC 106/SC 4,9599,[14244],[76995],"['en','fr']",8,<p>ISO 7492:2018 specifies the dimensions and performance requirements for dental explorers.</p><p>ISO 7492:2018 is not applicable to endodontic explorers.</p>

14245,IS,,ISO 7493:1985,Dental operator's stool,Siège d'opérateur dentaire,1985-11-28,1,['11.060.20'],ISO/TC 106/SC 6,9599,,[14246],"['en','fr']",5,

14246,IS,,ISO 7493:1997,Dental operator's stool,Siège d'opérateur dentaire,1997-05-01,2,['11.060.20'],ISO/TC 106/SC 6,9599,[14245],[39815],"['en','fr']",7,

31409,IS,Cor,ISO 7493:1997/Cor 1:1999,Dental operator's stool — Technical Corrigendum 1,Siège d'opérateur dentaire — Rectificatif technique 1,1999-07-01,2,['11.060.20'],ISO/TC 106/SC 6,9599,,[39815],"['en','fr']",1,

40534,IS,,ISO 7494-1:2004,Dentistry — Dental units — Part 1: General requirements and test methods,Art dentaire — Units dentaires — Partie 1: Exigences et méthodes d'essai générales,2004-11-17,1,['11.060.20'],ISO/TC 106/SC 6,9599,[14248],[50324],"['en','fr']",15,"<p>ISO 7494-1:2004 specifies requirements and test methods for dental units, regardless of whether or not they are electrically powered.</p><p>ISO 7494-1:2004 also specifies requirements for manufacturer's instructions, marking and packaging.</p>"

50324,IS,,ISO 7494-1:2011,Dentistry — Dental units — Part 1: General requirements and test methods,Médecine bucco-dentaire — Units dentaires — Partie 1: Exigences générales et méthodes d'essai,2011-08-05,2,['11.060.20'],ISO/TC 106/SC 6,9599,[40534],[69100],"['en','fr']",7,"<p>ISO 7494-1:2011 specifies requirements and test methods for dental units, regardless of whether or not they are electrically powered.</p><p>ISO 7494-1:2011 also specifies requirements for manufacturer's instructions, marking and packaging.</p>"

14247,IS,,ISO 7494:1990,Dental unit,Unit dentaire,1990-04-05,1,['11.060.20'],ISO/TC 106/SC 6,9599,,[14248],"['en','fr']",9,

14248,IS,,ISO 7494:1996,Dental units,Units dentaires,1996-03-07,2,['11.060.20'],ISO/TC 106/SC 6,9599,[14247],"[33826,40534]","['en','fr']",11,"<p>Is one of a series of International Standards based on IEC 601-1. Specifies requirements and test methods for dental units, regardless of their construction and regardless of whether or not they are electrically powered. Contains also the requirements for manufacturer's instructions, marking and packaging. Replaces the first edition.</p>"

33826,IS,,ISO 7494-2:2003,Dentistry — Dental units — Part 2: Water and air supply,Art dentaire — Units dentaires — Partie 2: Alimentation en eau et en air,2003-03-06,1,['11.060.20'],ISO/TC 106/SC 6,9599,[14248],[59875],"['en','fr']",8,"<p>ISO 7494-2:2003 specifies requirements and test methods for the materials, design and construction of the water and air supply within dental units in order to ensure that the compressed water and air supplied via the dental unit are of appropriate quality. It includes provisions for the prevention of retraction of oral fluids into the water supply of the dental unit.</p><p>ISO 7494-2:2003 does not address prevention of contamination and/or proliferation of

59875,IS,,ISO 7494-2:2015,"Dentistry — Stationary dental units — Part 2: Air, water, suction and wastewater systems","Médecine bucco-dentaire — Units dentaires fixes — Partie 2: Systèmes d'alimentation en air et en eau, d'aspiration et d'évacuation des eaux usées",2015-03-26,2,['11.060.20'],ISO/TC 106/SC 6,9599,"[33826,19163]",[74497],"['en','fr']",24,"<p>ISO 7494-2:2015 specifies requirements and test methods concerning</p><p>a) the configuration of dental unit connections to the compressed air supply, water supply, suction supply, and wastewater drain plumbing,</p><p>b) the materials, design, and construction of the compressed air and water system within the dental unit,</p><p>c)

14249,IS,,ISO 7495:1990,Wheat flour — Determination of wet gluten content by mechanical means,Farines de blé tendre — Détermination du gluten humide par des moyens mécaniques,1990-07-12,1,['67.060'],ISO/TC 34/SC 4,9599,,"[37804,26705]","['en','fr']",5,

14252,IS,,ISO 7498:1984,Information processing systems — Open Systems Interconnection — Basic Reference Model,Systèmes de traitement de l'information — Interconnexion des systèmes ouverts — Modèle de Référence de base,1984-10-01,1,['35.100.01'],ISO/IEC JTC 1,9599,,[20269],"['en','fr']",40,

14255,IS,Cor,ISO 7498:1984/Cor 1:1988,Information processing systems — Open Systems Interconnection — Basic Reference Model — Technical Corrigendum 1,Systèmes de traitement de l'information — Interconnexion des systèmes ouverts — Modèle de Référence de base — Rectificatif technique 1,1988-12-22,1,['35.100'],ISO/IEC JTC 1,9599,,[20269],['en'],1,

14257,IS,,ISO 7498-3:1989,Information processing systems — Open Systems Interconnection — Basic Reference Model — Part 3: Naming and addressing,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Modèle de référence de base — Partie 3: Dénomination et adressage,1989-03-09,1,['35.100.01'],ISO/IEC JTC 1,9599,,[25022],"['en','fr']",20,

3717,IS,,ISO 75-1:1993,Plastics — Determination of temperature of deflection under load — Part 1: General test method,Plastiques — Détermination de la température de fléchissement sous charge — Partie 1: Méthode générale d'essai,1993-08-26,1,['83.080.01'],ISO/TC 61/SC 2,9599,[3716],[31255],"['en','fr']",5,"<p>The principle of the method specified is subjecting a standard test specimen to a bending stress under three-point loading to produce one of the nominal surface stresses in the relevant part of this standard, raising the temperature at a uniform rate, measuring the temperature, at which a specified deflection occurs. The results obtained do not necessarily represent maximum use temperat

31255,IS,,ISO 75-1:2004,Plastics — Determination of temperature of deflection under load — Part 1: General test method,Plastiques — Détermination de la température de fléchissement sous charge — Partie 1: Méthode d'essai générale,2004-05-12,2,['83.080.01'],ISO/TC 61/SC 2,9599,[3717],[57703],"['en','fr']",10,<p>ISO 75-1:2004 specifies a general test method for the determination of the temperature of deflection under load (flexural stress under three-point loading) of plastics. Different types of test specimen and different constant loads are defined to suit different types of material.</p>

57703,IS,,ISO 75-1:2013,Plastics — Determination of temperature of deflection under load — Part 1: General test method,Plastiques — Détermination de la température de fléchissement sous charge — Partie 1: Méthode d'essai générale,2013-04-09,3,['83.080.01'],ISO/TC 61/SC 2,9599,[31255],[77576],"['en','fr','ru']",9,<p>ISO 75-1:2013 gives a general test method for the determination of the temperature of deflection under load (flexural stress under three-point loading) of plastics. Different types of test specimen and different constant loads are defined to suit different types of material.</p>

3715,IS,,ISO 75:1974,Plastics and ebonite — Determination of temperature of deflection under load,Matières plastiques et ébonite — Détermination de la température de fléchissement sous charge,1974-11-01,1,['83.080.01'],ISO/TC 61,9599,,[3716],"['en','fr']",3,

3716,IS,,ISO 75:1987,Plastics and ebonite — Determination of temperature of deflection under load,Plastiques et ébonite — Détermination de la température de fléchissement sous charge,1987-03-26,2,['83.080'],ISO/TC 61/SC 2,9599,[3715],"[3718,3719,3717]","['en','fr']",4,

3718,IS,,ISO 75-2:1993,Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite,Plastiques — Détermination de la température de fléchissement sous charge — Partie 2: Plastiques et ébonite,1993-08-26,1,['83.080.10'],ISO/TC 61/SC 2,9599,[3716],[31256],"['en','fr']",3,"<p>The principle of the method specified is subjecting a standard test specimen to a bending stress to produce one of the nominal surface stresses (method A: 1,80 MPa, method B: 0,45 MPa, method C: 8,00 MPa), raising the temperature at a uniform rate, measuring the temperature, at which a specified deflection occurs. The test specimens are tested in one of two positions, flatwise or edgewise

31256,IS,,ISO 75-2:2004,Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite,Plastiques — Détermination de la température de fléchissement sous charge — Partie 2: Plastiques et ébonite,2004-05-12,2,['83.080.10'],ISO/TC 61/SC 2,9599,[3718],[55653],"['en','fr']",10,"<p>ISO 75-2:2004 specifies three methods, using different values of constant flexural stress, that can be used for the determination of the temperature of deflection under load of plastics (including filled plastics and fibre-reinforced plastics in which the fibre length, prior to processing, is up to 7,5 mm) and ebonite:</p><ul><li>method A, using a flexural stress of 1,80 MPa;</li><li>me

3719,IS,,ISO 75-3:1993,Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics,Plastiques — Détermination de la température de fléchissement sous charge — Partie 3: Stratifiés thermodurcissables à haute résistance et plastiques renforcés de fibres longues,1993-08-26,1,"['83.120','83.080.10']",ISO/TC 61/SC 2,9599,[3716],[31257],"['en','fr']",3,"<p>The principle of the method specified is subjecting a standard test specimen to a bending stress equal to 1/10 of a specified or measured flexural strength, raising the temperature at a uniform rate, measuring the temperature, at which a specified deflection

31257,IS,,ISO 75-3:2004,Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics,Plastiques — Détermination de la température de fléchissement sous charge — Partie 3: Stratifiés thermodurcissables à haute résistance et plastiques renforcés de fibres longues,2004-05-12,2,"['83.120','83.080.10']",ISO/TC 61/SC 2,9599,[3719],[85824],"['en','fr']",5,"<p>ISO 75-3:2004 specifies a method for the determination of the temperature of deflection under load of high-strength thermosetting laminates and compression-moulded long-fibre-reinforced plastics in which the fibre length is greater than 7,5 mm. The flexural

5006,IS,,ISO 750:1981,Fruit and vegetable products — Determination of titratable acidity,Produits dérivés des fruits et légumes — Détermination de l'acidité titrable,1981-11-01,1,['67.080.01'],ISO/TC 34/SC 3,9599,,[22569],"['en','fr']",3,

14260,IS,,ISO 7500-1:1986,Metallic materials — Verification of static uniaxial testing machines — Part 1: Tensile testing machines,Matériaux métalliques — Vérification des machines pour essais statiques uniaxiaux — Partie 1: Machines d'essai de traction,1986-03-20,1,['77.040.10'],ISO/TC 164/SC 1,9599,[3976],[28602],"['en','fr']",7,

28602,IS,,ISO 7500-1:1999,Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system,Matériaux métalliques — Vérification des machines pour essais statiques uniaxiaux — Partie 1: Machines d'essai de traction/compression — Vérification et étalonnage du système de mesure de charge,1999-09-23,2,['77.040.10'],ISO/TC 164/SC 1,9599,[14260],[34821],"['en','fr']",13,

34821,IS,,ISO 7500-1:2004,Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system,Matériaux métalliques — Vérification des machines pour essais statiques uniaxiaux — Partie 1: Machines d'essai de traction/compression — Vérification et étalonnage du système de mesure de force,2004-08-13,3,['77.040.10'],ISO/TC 164/SC 1,9599,[28602],[62997],"['en','fr']",17,"<p>ISO 7500-1:2004 specifies the verification of tension/compression testing machines. The verification consists of a general inspection of the testing machine, including its accessories for the force application and a c

51673,IS,Cor,ISO 7500-1:2004/Cor 1:2008,Metallic materials — Verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Verification and calibration of the force-measuring system — Technical Corrigendum 1,Matériaux métalliques — Vérification des machines pour essais statiques uniaxiaux — Partie 1: Machines d'essai de traction/compression — Vérification et étalonnage du système de mesure de force — Rectificatif technique 1,2008-06-11,3,['77.040.10'],ISO/TC 164/SC 1,9599,,[62997],"['en','fr']",2,

62997,IS,,ISO 7500-1:2015,Metallic materials — Calibration and verification of static uniaxial testing machines — Part 1: Tension/compression testing machines — Calibration and verification of the force-measuring system,Matériaux métalliques — Étalonnage et vérification des machines pour essais statiques uniaxiaux — Partie 1: Machines d'essai de traction/compression — Étalonnage et vérification du système de mesure de force,2015-12-07,4,['77.040.10'],ISO/TC 164/SC 1,9599,"[51673,34821]",[72572],"['en','fr']",18,"<p>ISO 7500-1:2015 specifies the calibration and verification of tension/compression testing machines.</p><p>The verification consists of:</p><p>- a general inspection of the te

14261,IS,,ISO 7500-2:1996,Metallic materials — Verification of static uniaxial testing machines — Part 2: Tension creep testing machines — Verification of the applied load,Matériaux métalliques — Vérification des machines pour essais statiques uniaxiaux — Partie 2: Machines d'essai de fluage en traction — Vérification de la charge appliquée,1996-10-03,1,['77.040.10'],ISO/TC 164/SC 1,9599,,[36338],"['en','fr']",9,

14265,IS,,ISO 7503-1:1988,"Evaluation of surface contamination — Part 1: Beta-emitters (maximum beta energy greater than 0,15 MeV) and alpha-emitters","Évaluation de la contamination de surface — Partie 1: Émetteurs bêta (énergie bêta maximale supérieure à 0,15 MeV) et émetteurs alpha",1988-08-11,1,['13.280'],ISO/TC 85/SC 2,9599,,"[40870,60522]","['en','fr']",11,"<p>Applies to surfaces of equipment and facilities, containers of radioactive materials and sealed sources, does not apply to the skin and contamination of clothing. Gives direct and indirect methods of measurement (the latter by means of smear tests). Is restricted to beta- and alpha-emitters, the production rate of which, with reg

14266,IS,,ISO 7503-2:1988,Evaluation of surface contamination — Part 2: Tritium surface contamination,Évaluation de la contamination de surface — Partie 2: Contamination de surface par le tritium,1988-08-11,1,['13.280'],ISO/TC 85/SC 2,9599,,[60056],"['en','fr']",4,"<p>Applies to surfaces of equipment and facilities, containers of radioactive materials and sealed sources, does not apply to the skin and contamination of clothing. Gives a method of direct measurement and an indirect method for removable surface contamination. Evaluation of surface contaminations from beta-emitters (maximum beta energy greater than 0,15 MeV) and alpha-emitters is dealt with in ISO 7503-1, other radionuclides of

2634,IS,,ISO 7503-3:1996,"Evaluation of surface contamination — Part 3: Isomeric transition and electron capture emitters, low energy beta-emitters (E bêtamax less than 0,15 MeV)","Évaluation de la contamination de surface — Partie 3: Émetteurs à transition isomérique et capture électronique, émetteurs bêta basse énergie (E bêtamax inférieur à 0,15 MeV)",1996-11-14,1,['13.280'],ISO/TC 85/SC 2,9599,,[61532],"['en','fr']",28,"<p>Applicable to the evaluation of contamination on surfaces of facilities and equipment, containers of radioactive materials and sealed sources by low energy beta-emitters (&lt;0,15 MeV) in terms of activity per unit area. Does not apply to the evaluation of contaminatio

14267,IS,,ISO 7504:1984,Gas analysis — Vocabulary,Analyse des gaz — Vocabulaire,1984-09-01,1,"['71.040.40','01.040.71']",ISO/TC 158,9599,,[24662],"['en','fr']",27,"<p>Defines terms relating to gas analysis, in English and in French. The vocabulary is restricted to the presentation of the methods most currently used in gas analysis. Alphabetical indexes in english and french languages are also given.</p>"

24662,IS,,ISO 7504:2001,Gas analysis — Vocabulary,Analyse des gaz — Vocabulaire,2001-11-22,2,"['71.040.40','01.040.71']",ISO/TC 158,9599,[14267],[53596],"['en','fr']",27,

14268,IS,,ISO 7505:1986,Forestry machinery — Chain saws — Measurement of hand-transmitted vibration,Machines forestières — Scies à chaîne — Mesurage des vibrations transmises aux mains,1986-05-08,1,"['65.060.80','13.160']",ISO/TC 23/SC 17,9599,,[35166],"['en','fr']",8,<p>Specifies general methods for data acquisition and processing concerning vibrations induced by chain saws. The methods are valid irrespective of how the chain saw is operated during the test. Figures illustrate the meaning of the description. An annex contains the frequency range and weigthing filter.</p>

14270,IS,,ISO 7507-1:1993,Petroleum and liquid petroleum products — Calibration of vertical cylindrical tanks — Part 1: Strapping method,Pétrole et produits pétroliers liquides — Jaugeage des réservoirs cylindriques verticaux — Partie 1: Méthode par ceinturage,1993-07-22,1,['75.180.30'],ISO/TC 28/SC 2,9599,,"[33726,37004]","['en','fr']",29,"<p>Applies to tanks with cylindrical courses that are substantially vertical. Provides a method suitable for use as a working method, a reference method or a referee method for measuring a tank using a steel strapping tape. The operation of strapping, the corrections to be made and the calculations leading to the compilation of the tank capacity table are

14271,IS,,ISO 7507-2:1993,Petroleum and liquid petroleum products — Calibration of vertical cylindrical tanks — Part 2: Optical-reference-line method,Pétrole et produits pétroliers liquides — Jaugeage des réservoirs cylindriques verticaux — Partie 2: Méthode par ligne de référence optique,1993-07-22,1,['75.180.30'],ISO/TC 28/SC 2,9599,,"[38912,33727]","['en','fr']",10,<p>Applies to tanks above 8 m in diameter with cylindrical courses that are substantially vertical. Provides a method for determining the volumetric quantity contained within a tank at gauged liquid levels using an optical plummet. The measurement required to determine the circumference may be made internally or externally. For

38912,IS,,ISO 7507-2:2005,Petroleum and liquid petroleum products — Calibration of vertical cylindrical tanks — Part 2: Optical-reference-line method,Pétrole et produits pétroliers liquides — Jaugeage des réservoirs cylindriques verticaux — Partie 2: Méthode par ligne de référence optique,2005-06-15,2,['75.180.30'],ISO/TC 28/SC 2,9599,[14271],[81047],"['en','fr','ru']",26,"<p>ISO 7507-2:2005 specifies a method for the calibration of tanks above eight metres in diameter with cylindrical courses that are substantially vertical. It provides a method for determining the volumetric quantity contained within a tank at gauged liquid levels.</p><p>The optical (offset) measurements required to determ

14272,IS,,ISO 7507-3:1993,Petroleum and liquid petroleum products — Calibration of vertical cylindrical tanks — Part 3: Optical-triangulation method,Pétrole et produits pétroliers liquides — Jaugeage des réservoirs cylindriques verticaux — Partie 3: Méthode par triangulation optique,1993-07-22,1,['75.180.30'],ISO/TC 28/SC 2,9599,,"[33728,38913]","['en','fr']",16,<p>Applies to tanks above 8 m in diameter with cylindrical courses that are substantially vertical. Provides a method for determining the volumetric quantity contained within a tank at gauged liquid levels by optical triangulation using theodolites and laser beams. The measurement required to determine the radius may be made internal

14274,IS,,ISO 7507-4:1995,Petroleum and liquid petroleum products — Calibration of vertical cylindrical tanks — Part 4: Internal electro-optical distance-ranging method,Pétrole et produits pétroliers liquides — Jaugeage des réservoirs cylindriques verticaux — Partie 4: Méthode par mesurage électro-optique interne de la distance,1995-06-29,1,['75.180.30'],ISO/TC 28/SC 2,9599,,[43660],"['en','fr']",10,"<p>Specifies a method for the calibration of vertical cylindrical tanks having diameters greater than 5 m by means of internal measurements using an electro-optical distance-ranging instrument (EODR), and for the subsequent compilation of tank capacity tables. Not applicable to the calibration o

14276,IS,,ISO 7509:2000,Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of time to failure under sustained internal pressure,Systèmes de canalisations en plastiques — Tubes en plastiques thermodurcissables renforcés de verre (PRV) — Détermination du temps mis jusqu'à la défaillance sous une pression interne constante,2000-07-06,1,['23.040.20'],ISO/TC 138/SC 6,9599,,[61012],['en'],5,

5007,IS,,ISO 751:1981,Fruit and vegetable products — Determination of water-insoluble solids content,Produits dérivés des fruits et légumes — Détermination de la teneur en résidu sec insoluble dans l'eau,1981-10-01,1,['67.080.01'],ISO/TC 34/SC 3,9599,,[22567],"['en','fr']",2,

14277,IS,,ISO 7510:1997,Plastics piping systems — Glass-reinforced plastics (GRP) components — Determination of the amounts of constituents using the gravimetric method,Systèmes de canalisations en matières plastiques — Composants plastiques renforcés de verre (PRV) — Détermination des teneurs des constituants par la méthode gravimétrique,1997-01-22,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,,[65189],"['en','fr']",6,"<p>Method for the determination of constituents of a test sample cut from glass-reinforced plastics. It includes the determination of resin, glass, aggregate and filler contents. Technically identical to EN 637:1994.</p>"

14288,IS,,ISO 7519:1991,Technical drawings — Construction drawings — General principles of presentation for general arrangement and assembly drawings,Dessins techniques — Dessins de construction — Principes généraux de présentation pour des dessins d'ensemble et d'assemblage,1991-11-21,1,['01.100.30'],ISO/TC 10/SC 8,9599,,[83163],"['en','fr']",8,"<p>Establishes general requirements, thicknesses of lines, and the simplified representation of doors and windows. Describes the conventional representation, and gives arrow symbols. Annex A is for information only.</p>"

83163,IS,,ISO 7519:2024,Technical product documentation (TPD) — Construction documentation — General principles of presentation for general arrangement and assembly drawings,Documentation technique de produits (TPD) — Documentation de construction — Principes généraux de présentation pour les dessins de disposition générale et d’assemblage,2024-03-15,2,['01.100.30'],ISO/TC 10/SC 8,9599,[14288],[89718],"['en','fr']",26,"<p class='MsoBodyText'><span lang='EN-GB'>This document establishes general principles of presentation to be applied to construction drawings for general arrangement and assembly, mainly within the field of building and architectural drawings.</span></p>"

5008,IS,,ISO 752:1981,Zinc ingots,Zinc en lingots,1981-04-01,1,['77.120.60'],ISO/TC 18,9599,,[32445],"['en','fr']",1,"<p>Specifies the designations and chemical compositions of qualities of zinc ingots with a minimum zinc content of 98,5 % (m/m), obtained by treatment of ores or of other zinc-bearing materials by a process of chemical or electrolytic reduction or by distillation.</p>"

14293,IS,,ISO 7524:1985,"Nickel, ferronickel and nickel alloys — Determination of carbon content — Infra-red absorption method after induction furnace combustion","Nickel, ferro-nickel et alliages de nickel — Dosage du carbone — Méthode par absorption dans l'infrarouge après combustion dans un four à induction",1985-12-19,1,"['77.100','77.120.40']",ISO/TC 155,9599,,"[72111,65093]","['en','fr']",8,"<p>Applies to carbon content of nickel and ferronickel in the range 0.001 to 2.0 % (m/m), and of nickel alloys in the range 0.001 to 0.5 % (m/m). Specifies principle, reagents and materials, apparatus, sampling and samples, procedure, expression of results, some notes and test report. Examples of c

14295,IS,,ISO 7526:1985,"Nickel, ferronickel and nickel alloys — Determination of sulfur content — Infra-red absorption method after induction furnace combustion","Nickel, ferro-nickel et alliages de nickel — Dosage du soufre — Méthode par absorption dans l'infrarouge après combustion dans un four à induction",1985-12-19,1,"['77.100','77.120.40']",ISO/TC 155,9599,,"[65094,72112]","['en','fr']",7,"<p>Applies to the determination of sulfur content of nickel and ferronickel in the range 0,001 to 0,3 % (m/m), and of nickel alloys in the range 0,001 to 0,1 % (m/m). Specifies principle, reagents and materials, apparatus, sampling and samples, procedure, expression of results, some notes and test r

14298,IS,,ISO 7529:1989,Nickel alloys — Determination of chromium content — Potentiometric titration method with ammonium iron(II) sulfate,Alliages de nickel — Dosage du chrome — Méthode par titrage potentiométrique avec le sulfate de fer(II) et d'ammonium,1989-10-26,1,['77.120.40'],ISO/TC 155,9599,,[70202],"['en','fr']",5,"<p>Applies to the determination of 1 % (m/m) to 25 % (m/m) chromium content in nickel alloys which do not contain insoluble chromium carbides, and which have a vanadium content of less than 0,2 % (m/m). Specifies principle, reagents, apparatus, sampling and sample preparation, procedure, expression of results, special cases and test report. Examples of composition of some

14299,IS,,ISO 7530-1:1990,Nickel alloys — Flame atomic absorption spectrometric analysis — Part 1: General requirements and sample dissolution,Alliages de nickel — Analyse par spectrométrie d'absorption atomique dans la flamme — Partie 1: Caractéristiques générales et mise en solution de l'échantillon,1990-12-06,1,['77.120.40'],ISO/TC 155,9599,,[65092],"['en','fr']",7,"<p>Specifies methods for the determination of up to 4 % (m/m) of cobalt, chromium, copper, iron, manganese and aluminium, up to 2 % (m/m) of silicon and from 0,05 % (m/m) to 1 % (m/m) of vanadium in nickel alloys. Typical compositions of some nickel alloys are given in annex B. This part of ISO 7530 specifies the general requi

14300,IS,,ISO 7530-2:1990,Nickel alloys — Flame atomic absorption spectrometric analysis — Part 2: Determination of cobalt content,Alliages de nickel — Analyse par spectrométrie d'absorption atomique dans la flamme — Partie 2: Dosage du cobalt,1990-12-06,1,['77.120.40'],ISO/TC 155,9599,,[65092],"['en','fr']",3,"<p>The method is applicable to cobalt contents between 0,01 % (m/m) and 4 % (m/m). The general requirements concerning the apparatus, sampling, dissolution of the test sample, atomic absorption measurements, calculations and test report are given in ISO 7530-1. Specifies principle, reagents, apparatus, sampling and sample preparation, procedure, expression of results and test report.<

14301,IS,,ISO 7530-3:1990,Nickel alloys — Flame atomic absorption spectrometric analysis — Part 3: Determination of chromium content,Alliages de nickel — Analyse par spectrométrie d'absorption atomique dans la flamme — Partie 3: Dosage du chrome,1990-12-06,1,['77.120.40'],ISO/TC 155,9599,,[65092],"['en','fr']",3,"<p>The method is applicable to chromium contents between 0,01 % (m/m) and 4 % (m/m). The general requirements concerning the apparatus, sampling, dissolution of the test sample, atomic absorption measurements, calculations and test report are given in ISO 7530-1. Specifies principle, reagents, apparatus, sampling and sample preparation, procedure, expression of results and test repo

14302,IS,,ISO 7530-4:1990,Nickel alloys — Flame atomic absorption spectrometric analysis — Part 4: Determination of copper content,Alliages de nickel — Analyse par spectrométrie d'absorption atomique dans la flamme — Partie 4: Dosage du cuivre,1990-12-06,1,['77.120.40'],ISO/TC 155,9599,,[65092],"['en','fr']",3,"<p>The method is applicable to copper contents between 0,01 and 4 % (m/m). The general requirements concerning the apparatus, sampling, dissolution of the test sample, atomic absorption measurements, calculations and test report are given in ISO 7530-1. Specifies principle, reagents, apparatus, sampling and sample preparation, procedure, expression of results and test report.</p>" 143

14303,IS,,ISO 7530-5:1990,Nickel alloys — Flame atomic absorption spectrometric analysis — Part 5: Determination of iron content,Alliages de nickel — Analyse par spectrométrie d'absorption atomique dans la flamme — Partie 5: Dosage du fer,1990-12-06,1,['77.120.40'],ISO/TC 155,9599,,[65092],"['en','fr']",3,"<p>The method is applicable to iron contents between 0,01 and 4 % (m/m). The general requirements concerning the apparatus, sampling, dissolution of the test sample, atomic absorption measurements, calculations and test report are given in ISO 7530-1. Specifies principle, reagents, apparatus, sampling and sample preparation, procedure, expression of results and test report.</p>"

14304,IS,,ISO 7530-6:1990,Nickel alloys — Flame atomic absorption spectrometric analysis — Part 6: Determination of manganese content,Alliages de nickel — Analyse par spectrométrie d'absorption atomique dans la flamme — Partie 6: Dosage du manganèse,1990-12-06,1,['77.120.40'],ISO/TC 155,9599,,[65092],"['en','fr']",3,"<p>The method is applicable to manganese contents between 0,01 % (m/m) and 4 % (m/m). The general requirements concerning the apparatus, sampling, dissolution of the test sample, atomic absorption measurements, calculations and test report are given in ISO 7530-1. Specifies principle, reagents, apparatus, sampling and sample preparation, procedure, expression of results and test

14309,IS,,ISO 7532:1985,Instant coffee — Size analysis,Café soluble — Analyse granulométrique,1985-10-31,1,['67.140.20'],ISO/TC 34/SC 15,9599,,[26856],"['en','fr']",2,"<p>The method consists in separating of a test portion into fractions according to particle size, by manual or mechanical sieving, using test sieves, and expression of results as percentages by mass.</p>"

14310,IS,,ISO 7534:1985,Instant coffee — Determination of insoluble matter content,Café soluble — Détermination des matières insolubles,1985-11-07,1,['67.140.20'],ISO/TC 34/SC 15,9599,,[28400],"['en','fr']",3,

14313,IS,,ISO 7537:1989,Petroleum products — Determination of total acid number — Semi-micro colour-indicator titration method,Produits pétroliers — Détermination de l'indice d'acide total — Semi-microméthode de titrage par indicateur coloré,1989-09-21,1,['75.080'],ISO/TC 28,9599,,[26477],"['en','fr']",6,

14314,IS,,ISO 7539-1:1987,Corrosion of metals and alloys — Stress corrosion testing — Part 1: General guidance on testing procedures,Corrosion des métaux et alliages — Essais de corrosion sous contrainte — Partie 1: Guide général des méthodes d'essai,1987-08-20,1,['77.060'],ISO/TC 156,9599,,"[54369,40859]","['en','fr']",11,<p>Descsribes the general considerations which apply when designing and conducting tests to assess susceptibility of metals to stress corrosion. Particular methods of test are not treated in detail in this document. These are specified in the additional parts of ISO 7539.</p>

55856,IS,,ISO 7539-10:2013,Corrosion of metals and alloys — Stress corrosion testing — Part 10: Reverse U-bend method,Corrosion des métaux et alliages — Essais de corrosion sous contrainte — Partie 10: Méthode d'essai par cintrage en U inversé,2013-03-05,1,['77.060'],ISO/TC 156,9599,,[77214],"['en','fr']",11,"<p>ISO 7539-10:2013 covers procedures for designing, preparing and using reversed U-bend (RUB) test specimens for investigating the susceptibility of the metal to stress corrosion cracking. The term 'metal' as used in this standard includes alloys.</p>"

14319,IS,,ISO 7539-6:1989,Corrosion of metals and alloys — Stress corrosion testing — Part 6: Preparation and use of pre-cracked specimens,Corrosion des métaux et alliages — Essais de corrosion sous contrainte — Partie 6: Préparation et utilisation des éprouvettes préfissurées,1989-12-21,1,['77.060'],ISO/TC 156,9599,,[37001],"['en','fr']",30,"<p>Covers procedures for designing, preparing and using pre cracked specimens . Recommendations concerning notched specimens are given in annex A. These specimens are not suitable for the evaluation of thin product (sheet or wire); they are generally used for plate, bar and forgings. Their advantage is that they allow date to be acquired from which crit

37001,IS,,ISO 7539-6:2003,Corrosion of metals and alloys — Stress corrosion testing — Part 6: Preparation and use of pre-cracked specimens for tests under constant load or constant displacement,Corrosion des métaux et alliages — Essais de corrosion sous contrainte — Partie 6: Préparation et utilisation des éprouvettes préfissurées pour essais sous charge constante ou sous déplacement constant,2003-02-06,2,['77.060'],ISO/TC 156,9599,[14319],[57621],"['en','fr']",38,"<p>ISO 7539-6:2002 covers procedures for designing, preparing and using pre-cracked specimens for investigating susceptibility to stress corrosion. It gives recommendations for the design, preparation and use of pre-cracked specim

57621,IS,,ISO 7539-6:2011,Corrosion of metals and alloys — Stress corrosion testing — Part 6: Preparation and use of precracked specimens for tests under constant load or constant displacement,Corrosion des métaux et alliages — Essais de corrosion sous contrainte — Partie 6: Préparation et utilisation des éprouvettes préfissurées pour essais sous charge constante ou sous déplacement constant,2011-10-10,3,['77.060'],ISO/TC 156,9599,[37001],[74172],"['en','fr']",38,"<p>ISO 7539-6:2011 covers procedures for designing, preparing and using precracked specimens for investigating susceptibility to stress corrosion. It gives recommendations for the design, preparation and use of precracked specimens

14320,IS,,ISO 7539-7:1989,Corrosion of metals and alloys — Stress corrosion testing — Part 7: Slow strain rate testing,Corrosion des métaux et alliages — Essais de corrosion sous contrainte — Partie 7: Essais à faible vitesse de déformation,1989-12-07,1,['77.060'],ISO/TC 156,9599,,[34209],"['en','fr']",4,"<p>Covers procedures for conducting slow strain rate tests for investigating susceptibility to stress corrosion cracking, including hydrogen-induced failure. They are adaptable for testing a wide variety of product forms. Their advantage is the rapidity with which susceptibility to stress corrosion cracking of a particular metal/environment combination can be assessed.</p>"