Withdrawn and superseded ISO standards — page 145 of 246

4778,IS,,ISO 647:1974,"Brown coals and lignites — Determination of the yields of tar, water, gas and coke residue by low temperature distillation","Charbons bruns et lignites — Détermination des rendements en goudron, en eau, en gaz et en résidu de coke par distillation à basse température",1974-11-01,1,['73.040'],ISO/TC 27/SC 5,9599,,[70840],"['en','fr']",6,"<p>The sample is heated in an aluminium retort to a temperatur of 520 °C. The products of decomposition pass into a water-cooled receiver; the tar and water are condensed while gaseous products pass to atmosphere. The coke residue and the receiver and its contents are weighed. The mass of tar is obtained by difference to the mass of wat

12829,IS,,ISO 6471:1983,"Rubber, vulcanized — Determination of crystallization effects under compression",Caoutchouc vulcanisé — Détermination des effets de la cristallisation sous compression,1983-12-01,1,['83.060'],ISO/TC 45/SC 2,9599,,[12830],"['en','fr']",6,

12831,IS,,ISO 6472:1986,Rubber compounding ingredients — Abbreviations,Ingrédients de mélange du caoutchouc — Abréviations,1986-05-01,1,['83.040.20'],ISO/TC 45,9599,,[2286],"['en','fr']",2,

2286,IS,,ISO 6472:1994,Rubber compounding ingredients — Abbreviations,Ingrédients de mélange du caoutchouc — Abréviations,1994-07-14,2,['83.040.20'],ISO/TC 45,9599,[12831],[33980],"['en','fr']",9,"<p>Establishes unambiguous abbreviations for commonly used rubber compounding ingredients, other than polymers, derived from a consensus of world opinion.</p>"

23790,IS,Amd,ISO 6472:1994/Amd 1:1999,Rubber compounding ingredients — Abbreviations — Amendment 1: New materials,Ingrédients de mélange du caoutchouc — Abréviations — Amendement 1: Nouveaux matériaux,1999-04-01,2,['83.040.20'],ISO/TC 45,9599,,[33980],"['en','fr']",5,

33980,IS,,ISO 6472:2004,Rubber compounding ingredients — Abbreviations,Ingrédients de mélange du caoutchouc — Abréviations,2004-02-11,3,['83.040.20'],ISO/TC 45,9599,"[23790,2286]",[51262],"['en','fr']",17,"<p>ISO 6472:2004 establishes unambiguous abbreviations for commonly used rubber compounding ingredients of known, specific chemical composition.</p><p>The abbreviations are derived from common usage in industry and commerce rather than from any systematic nomenclature. The list is not intended to conflict with, but rather to act as a supplement to, existing trade-names and trademarks.</p><p>The list does not purport to be comprehensive, and abbreviations for other compounding ingredients w

51262,IS,,ISO 6472:2010,Rubber compounding ingredients — Symbols and abbreviated terms,Ingrédients de mélange du caoutchouc — Symboles et termes abrégés,2010-09-16,4,"['01.040.83','83.040.20']",ISO/TC 45,9599,[33980],[70337],"['en','fr','ru']",17,"<p>ISO 6472:2010 establishes unambiguous symbols and abbreviated terms for commonly used rubber compounding ingredients of known, specific chemical composition.</p>"

70337,IS,,ISO 6472:2017,Rubber compounding ingredients — Abbreviated terms,Ingrédients de mélange du caoutchouc — Termes abrégés,2017-06-30,5,"['01.040.83','83.040.20']",ISO/TC 45,9599,[51262],[86380],"['en','fr']",17,"<p>ISO 6472:2017 establishes unambiguous abbreviated terms for commonly used rubber compounding ingredients of known, specific chemical composition.</p>"

45577,IS,,ISO 6474-1:2010,Implants for surgery — Ceramic materials — Part 1: Ceramic materials based on high purity alumina,Implants chirurgicaux — Produits céramiques — Partie 1: Produits céramiques à base d'alumine de haute pureté,2010-01-28,1,['11.040.40'],ISO/TC 150/SC 1,9599,[12837],[69906],"['en','fr','ru']",9,"<p>ISO 6474-1:2010 specifies the characteristics of, and corresponding test methods for, a bio-compatible and bio-stable ceramic bone substitute material based on high purity alumina for use as bone spacers, bone replacements and components of orthopaedic joint prostheses.</p>"

12836,IS,,ISO 6474:1981,Implants for surgery — Ceramic materials based on alumina,Implants chirurgicaux — Produits céramiques à base d'alumine,1981-02-01,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[12837],"['en','fr']",3,

12837,IS,,ISO 6474:1994,Implants for surgery — Ceramic materials based on high purity alumina,Implants chirurgicaux — Produits céramiques à base d'alumine de haute pureté,1994-02-03,2,['11.040.40'],ISO/TC 150/SC 1,9599,[12836],"[34585,45577]","['en','fr']",6,<p>Specification of characteristics and corresponding test methods for biocompatible and bio-stable ceramic bone substitutes based on high purity alumina.</p>

50699,IS,,ISO 6474-2:2012,Implants for surgery — Ceramic materials — Part 2: Composite materials based on a high-purity alumina matrix with zirconia reinforcement,Implants chirurgicaux — Produits céramiques — Partie 2: Matériaux composites à matrice alumine de haute pureté renforcée par des grains de zircone,2012-04-16,1,['11.040.40'],ISO/TC 150/SC 1,9599,,[72592],"['en','fr']",12,

12839,IS,,ISO 6475-1:1980,"Implants for surgery — Metal bone screws — Mechanical requirements and methods of test — Part 1: Screws with asymmetrical thread, variable fitting (spherical), stainless steel","Implants chirurgicaux — Vis métalliques pour os — Propriétés mécaniques et méthodes d'essai — Partie 1: Vis à filet asymétrique, embase (sphérique) variable, en acier inoxydable",1980-10-01,1,['11.040.40'],ISO/TC 150/SC 5,9599,,[12838],"['en','fr']",2,

12840,IS,,ISO 6475-2:1980,"Implants for surgery — Metal bone screws — Mechanical requirements and methods of test — Part 2: Screws with asymmetrical thread, constant fitting (spherical), stainless steel","Implants chirurgicaux — Vis métalliques pour os — Propriétés mécaniques et méthodes d'essai — Partie 2: Vis à filet asymétrique, embase (sphérique) constante, en acier inoxydable",1980-10-01,1,['11.040.40'],ISO/TC 150/SC 5,9599,,[12838],"['en','fr']",2,

4779,IS,,ISO 648:1977,Laboratory glassware — One-mark pipettes,Verrerie de laboratoire — Pipettes à un trait,1977-12-01,1,['17.060'],ISO/TC 48,9599,,[44142],"['en','fr']",7,"<p>The basis of adjustment, volumetric accuracy and capacity are considered and the series of capacities is given specified with and without bulbs. The limits of volumetric error, the construction and dimensions, delivery time and inscription are defined. The specified details comply with ISO 384.</p>"

12844,IS,,ISO 6480:1983,Conditions of acceptance for horizontal internal broaching machines — Testing of the accuracy,Conditions de réception des machines horizontales à brocher les intérieurs — Contrôle de la précision,1983-04-01,2,['25.080.30'],ISO/TC 39/SC 2,9599,,"[71541,73815]","['en','fr']",9,"<p>Specifies geometrical tests for these general purpose and normal accuracy broaching machines and gives the corresponding permissible deviations apply. Gives also the terminology used for the main elements of the machine (in English, French and Russian as well as the equivalent terms in German and Italian). It deals only with the verification of accuracy of the machine. It does not apply to the

12845,IS,,ISO 6481:1981,Acceptance conditions for vertical surface type broaching machines — Testing of accuracy,Conditions de réception des machines verticales à brocher les extérieurs — Contrôle de la précision,1981-10-01,1,['25.080.30'],ISO/TC 39/SC 2,9599,,"[71542,73811]","['en','fr']",9,"<p>specifies both preliminary levelling and geometrical tests for these general purpose and normal accuracy broaching machines, and gives the corresponding permissible deviations which apply. Gives also the terminology used for the main elements of the machine (in English, French and Russian as well as the equivalent terms in German and Italian). It deals only with the verification of accuracy of the ma

12846,IS,,ISO 6482:1980,Shipbuilding — Deck machinery — Warping end profiles,Construction navale — Auxiliaires de pont — Profils de poupée,1980-10-01,1,['47.020.50'],ISO/TC 8/SC 4,9599,,[67862],"['en','fr']",3,"<p>Specifies the types, nominal sizes, dimensions and designation of warping end profiles mounted on extensions of vertical or horizontal shafts and intended for windlasses, capstans, mooring winches and various shipboard winches including winches used for fishery and for hauling in steel wire rope and ropes of natural and man-made fibre.</p>"

12848,IS,,ISO 6484:1980,Earth-moving machinery — Elevating scrapers — Volumetric rating,Engins de terrassement — Décapeuses élévatrices — Évaluation volumétrique,1980-10-01,1,['53.100'],ISO/TC 127/SC 1,9599,,[12849],"['en','fr']",4,

12851,IS,,ISO 6486-1:1981,Ceramic ware in contact with food — Release of lead and cadmium — Part 1: Method of test,Articles en céramique en contact avec les aliments — Émission de plomb et de cadmium — Partie 1: Méthode d'essai,1981-06-01,1,"['81.060.20','97.040.60','67.250']",ISO/TC 166,9599,,[27280],"['en','fr']",4,

27280,IS,,ISO 6486-1:1999,"Ceramic ware, glass-ceramic ware and glass dinnerware in contact with food — Release of lead and cadmium — Part 1: Test method","Vaisselle en céramique, vaisselle en vitrocéramique et vaisselle de table en verre en contact avec les aliments — Émission de plomb et de cadmium — Partie 1: Méthode d'essai",1999-12-16,2,"['81.060.20','81.040.30','97.040.60','67.250']",ISO/TC 166,9599,[12851],[67561],"['en','fr']",11,

12852,IS,,ISO 6486-2:1981,Ceramic ware in contact with food — Release of lead and cadmium — Part 2: Permissible limits,Articles en céramique en contact avec les aliments — Émission de plomb et de cadmium — Partie 2: Limites admissibles,1981-08-01,1,"['81.060.20','97.040.60','67.250']",ISO/TC 166,9599,,[27281],"['en','fr']",2,

12853,IS,,ISO 6487:1980,Road vehicles — Techniques of measurement in impact tests — Instrumentation,Véhicules routiers — Techniques de mesurage lors des essais de chocs — Instrumentation,1980-10-01,1,['43.020'],ISO/TC 22,9599,,[12854],"['en','fr']",5,

12854,IS,,ISO 6487:1987,Road vehicles — Measurement techniques in impact tests — Instrumentation,Véhicules routiers — Techniques de mesurage lors des essais de chocs — Instrumentation,1987-06-25,2,['43.020'],ISO/TC 22,9599,[12853],[22193],"['en','fr']",6,

22193,IS,,ISO 6487:2000,Road vehicles — Measurement techniques in impact tests — Instrumentation,Véhicules routiers — Techniques de mesurage lors des essais de chocs — Instrumentation,2000-05-04,3,['43.020'],ISO/TC 22,9599,[12854],[35448],"['en','fr']",13,

35448,IS,,ISO 6487:2002,Road vehicles — Measurement techniques in impact tests — Instrumentation,Véhicules routiers — Techniques de mesurage lors des essais de chocs — Instrumentation,2002-10-17,4,['43.020'],ISO/TC 22,9599,[22193],[52058],"['en','fr']",12,"<p>ISO 6487 gives requirements and recommendations for measurement techniques involving the instrumentation used in impact tests carried out on road vehicles. Its requirements are aimed at facilitating comparisons between results obtained by different testing laboratories, while its recommendations will assist such laboratories in meeting those requirements. It is applicable to instrumentation including that used in the impact testing of v

45461,IS,Amd,ISO 6487:2002/Amd 1:2008,Road vehicles — Measurement techniques in impact tests — Instrumentation — Amendment 1: .,Véhicules routiers — Techniques de mesurage lors des essais de chocs — Instrumentation — Amendement 1: .,2008-07-10,4,['43.020'],ISO/TC 22,9599,,[52058],"['en','fr']",3,

52058,IS,,ISO 6487:2012,Road vehicles — Measurement techniques in impact tests — Instrumentation,Véhicules routiers — Techniques de mesurage lors des essais de chocs — Instrumentation,2012-09-24,5,['43.020'],ISO/TC 22/SC 36,9599,"[35448,45461]",[64041],"['en','fr']",16,

12856,IS,,ISO 6488-1:1997,Tobacco — Determination of water content — Part 1: Karl Fischer method,Tabac — Détermination de la teneur en eau — Partie 1: Méthode de Karl Fischer,1997-12-25,1,['65.160'],ISO/TC 126,9599,,[36240],"['en','fr']",5,

36240,IS,,ISO 6488:2004,Tobacco and tobacco products — Determination of water content — Karl Fischer method,Tabac et produits du tabac — Détermination de la teneur en eau — Méthode de Karl Fischer,2004-02-09,2,['65.160'],ISO/TC 126,9599,[12856],[79003],"['en','fr']",8,<p>ISO 6488:2004 specifies a method for the determination of water content by the Karl Fischer method. It is applicable to raw tobacco as well as tobacco taken from finished products. The method is suitable for water contents ranging from a mass fraction of at least 2 % to 55 %.</p>

51801,IS,Cor,ISO 6488:2004/Cor 1:2008,Tobacco and tobacco products — Determination of water content — Karl Fischer method — Technical Corrigendum 1,Tabac et produits du tabac — Détermination de la teneur en eau — Méthode de Karl Fischer — Rectificatif technique 1,2008-06-11,2,['65.160'],ISO/TC 126,9599,,[79003],"['en','fr']",1,

12857,IS,,ISO 6489-1:1980,Agricultural vehicles — Mechanical connections on towing vehicles — Part 1: Hook type — Dimensions,Véhicules agricoles — Liaisons mécaniques sur véhicules remorquants — Partie 1: Type crochet — Dimensions,1980-10-01,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[12858],"['en','fr']",1,

12858,IS,,ISO 6489-1:1991,Agricultural vehicles — Mechanical connections on towing vehicles — Part 1: Hook type,Véhicules agricoles — Liaisons mécaniques sur véhicules remorquants — Partie 1: Type crochet,1991-09-12,2,['65.060.10'],ISO/TC 23/SC 4,9599,[12857],[21074],"['en','fr']",2,

12859,IS,,ISO 6489-2:1980,Agricultural vehicles — Mechanical connections on towing vehicles — Part 2: Clevis type — Dimensions,Véhicules agricoles — Liaisons mécaniques sur véhicules remorquants — Partie 2: Type chape — Dimensions,1980-10-01,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[31683],"['en','fr']",2,

12860,IS,,ISO 6489-3:1992,Agricultural vehicles — Mechanical connections on towing vehicles — Part 3: Tractor drawbar,Véhicules agricoles — Liaisons mécaniques sur véhicules remorquants — Partie 3: Barre d'attelage du tracteur,1992-12-03,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[29687],"['en','fr']",3,"<p>Specifies the dimensional requirements, location and vertical static loads. Annex A gives drawbar locations for special applications.</p>"

29687,IS,,ISO 6489-3:2004,Agricultural vehicles — Mechanical connections between towed and towing vehicles — Part 3: Tractor drawbar,Véhicules agricoles — Liaisons mécaniques entre véhicules remorqueurs et véhicules remorqués — Partie 3: Barre d'attelage du tracteur,2004-06-02,2,['65.060.10'],ISO/TC 23/SC 4,9599,"[12860,30397]","[73563,69763]","['en','fr']",7,"<p>ISO 6489-3:2004 specifies the dimensional requirements and location for category 0, 1, 2, 3, 4 and 5 drawbars mounted on the rear of agricultural tractors.</p>"

51409,IS,,ISO 6489-5:2011,Agricultural vehicles — Mechanical connections between towed and towing vehicles — Part 5: Specifications for non-swivel clevis couplings,Véhicules agricoles — Liaisons mécaniques entre véhicules remorqueurs et véhicules remorqués — Partie 5: Spécifications pour attelages de type chape non rotatifs,2011-07-14,1,['65.060.10'],ISO/TC 23/SC 4,9599,,"[69764,72748]","['en','fr']",8,<p>ISO 6489-5:2011 specifies the requirements for non-swivel clevis couplings used for the attachment of agricultural trailers and implements equipped with a swivel hitch ring as specified in ISO 5692-3 to the rear of self-propelled agricultural vehicles.</p>

12863,IS,,ISO 6491:1980,Animal feeding stuffs — Determination of total phosphorus content — Spectrophotometric method,Aliments des animaux — Détermination de la teneur en phosphore total — Méthode spectrophotométrique,1980-08-01,1,['65.120'],ISO/TC 34/SC 10,9599,,[12864],"['en','fr']",3,

12868,IS,,ISO 6495:1980,Animal feeding stuffs — Determination of water-soluble chlorides content,Aliments des animaux — Détermination de la teneur en chlorures solubles dans l'eau,1980-09-01,1,['65.120'],ISO/TC 34/SC 10,9599,,[12869],"['en','fr']",3,

12869,IS,,ISO 6495:1999,Animal feeding stuffs — Determination of water-soluble chlorides content,Aliments des animaux — Détermination de la teneur en chlorures solubles dans l'eau,1999-04-15,2,['65.120'],ISO/TC 34/SC 10,9599,[12868],"[45505,60533,45506,61992]","['en','fr']",7,

12870,IS,,ISO 6496:1983,Animal feeding stuffs — Determination of moisture content,Aliments des animaux — Détermination de la teneur en eau,1983-08-01,1,['65.120'],ISO/TC 34/SC 10,9599,,[12871],"['en','fr']",3,

12873,IS,,ISO 6498:1983,Animal feeding stuffs — Preparation of test samples,Aliments des animaux — Préparation des échantillons pour essai,1983-10-01,1,['65.120'],ISO/TC 34/SC 10,9599,,[12874],"['en','fr']",6,

12874,IS,,ISO 6498:1998,Animal feeding stuffs — Preparation of test samples,Aliments des animaux — Préparation des échantillons pour essai,1998-11-12,2,['65.120'],ISO/TC 34/SC 10,9599,[12873],"[52285,41808]","['en','fr']",8,

12875,IS,,ISO 6500:1980,Powered industrial trucks — Service brakes — Component strength-performance requirements,Chariots de manutention automoteurs — Freins de service — Exigences de résistance mécanique pour les composants,1980-04-01,1,['53.060'],ISO/TC 110,9599,,[12576],"['en','fr']",1,

12877,IS,,ISO 6501:1988,Ferronickel — Specification and delivery requirements,Ferro-nickel — Spécifications et conditions de livraison,1988-12-01,1,['77.100'],ISO/TC 155,9599,,"[65949,77250]","['en','fr']",3,"<p>Specifies the technical delivery requirements for various forms of ferronickel (ingots, pieces, shot) usually delivered to foundries and steel-melting shops. Specifies furthermore definition, information for ordering, control, dispatch and storage.</p>"

70967,IS,,ISO 6502-1:2018,Rubber — Measurement of vulcanization characteristics using curemeters — Part 1: Introduction,Caoutchouc — Mesure des caractéristiques de vulcanisation à l'aide de rhéomètres — Partie 1: Introduction,2018-07-24,1,['83.060'],ISO/TC 45/SC 2,9599,[68356],[88769],"['en','fr']",14,<p>This document provides an introduction to the determination of vulcanization characteristics of rubber compounds by means of curemeters.</p>

12878,IS,,ISO 6502:1983,Rubber — Measurement of vulcanization characteristics with rotorless curemeters,Caoutchouc — Détermination des caractéristiques de vulcanisation à l'aide de rhéomètres sans rotor,1983-12-01,1,['83.060'],ISO/TC 45/SC 2,9599,,[12879],"['en','fr']",8,

12879,IS,,ISO 6502:1991,Rubber — Measurement of vulcanization characteristics with rotorless curemeters,Caoutchouc — Détermination des caractéristiques de vulcanisation à l'aide de rhéomètres sans rotor,1991-05-09,2,['83.060'],ISO/TC 45/SC 2,9599,[12878],[20179],"['en','fr']",7,

20179,IS,,ISO 6502:1999,Rubber — Guide to the use of curemeters,Caoutchouc — Guide pour l'emploi des rhéomètres,1999-12-02,3,['83.060'],ISO/TC 45/SC 2,9599,[12879],[68356],['en'],19,

70968,IS,,ISO 6502-2:2018,Rubber — Measurement of vulcanization characteristics using curemeters — Part 2: Oscillating disc curemeter,Caoutchouc — Mesure des caractéristiques de vulcanisation à l'aide de rhéomètres — Partie 2: Rhéomètre à disque oscillant,2018-07-24,1,['83.060'],ISO/TC 45/SC 2,9599,[42239],[88770],"['en','fr']",13,<p>This document specifies a method for determining selected vulcanization characteristics of a rubber compound by means of an oscillating disc curemeter. The introduction to the use of curemeters is described in ISO 6502‑1.</p>

68356,IS,,ISO 6502:2016,Rubber — Guide to the use of curemeters,Caoutchouc — Guide pour l'emploi des rhéomètres,2016-01-12,4,['83.060'],ISO/TC 45/SC 2,9599,[20179],[70967],"['en','fr']",21,<p>ISO 6502:2016 provides guidance on the determination of vulcanization characteristics of rubber compounds by means of curemeters.</p>

70969,IS,,ISO 6502-3:2018,Rubber — Measurement of vulcanization characteristics using curemeters — Part 3: Rotorless curemeter,Caoutchouc — Mesure des caractéristiques de vulcanisation à l'aide de rhéomètres — Partie 3: Rhéomètre sans rotor,2018-07-24,1,['83.060'],ISO/TC 45/SC 2,9599,,[83177],"['en','fr']",20,<p>This document specifies a method for determining selected vulcanization characteristics of a rubber compound by means of a rotorless curemeter. The introduction to the use of curemeters is given in ISO 6502‑1.</p>

12882,IS,,ISO 6504-1:1983,Paints and varnishes — Determination of hiding power — Part 1: Kubelka-Munk method for white and light-coloured paints,Peintures et vernis — Détermination du pouvoir masquant — Partie 1: Méthode de Kubelka-Munk pour les peintures blanches et les peintures claires,1983-05-01,1,['87.040'],ISO/TC 35/SC 9,9599,,"[70902,39403,23248]","['en','fr']",31,"<p>Specifies a method to be used for determining the spreading rate necessary to give a contrast ratio of 98 % of coating materials. The method is restricted to paint films having the tri-stimulus value of Y 70; it is not applicable to fluorescent or metallic paint materials. The principle of the method is based on the Kube

1985,IS,,ISO 6504-3:1998,Paints and varnishes — Determination of hiding power — Part 3: Determination of contrast ratio (opacity) of light-coloured paints at a fixed spreading rate,Peintures et vernis — Détermination du pouvoir masquant — Partie 3: Détermination du rapport de contraste (pouvoir masquant) des peintures claires à un rendement surfacique déterminé,1998-07-16,1,['87.040'],ISO/TC 35/SC 9,9599,"[9525,9522,9523,9524]",[39402],"['en','fr']",6,

39402,IS,,ISO 6504-3:2006,Paints and varnishes — Determination of hiding power — Part 3: Determination of contrast ratio of light-coloured paints at a fixed spreading rate,Peintures et vernis — Détermination du pouvoir masquant — Partie 3: Détermination du rapport de contraste des peintures claires à un rendement surfacique déterminé,2006-02-13,2,['87.040'],ISO/TC 35/SC 9,9599,[1985],[70903],"['en','fr','ru']",7,"<p>ISO 6504-3:2006 describes methods for determining the opacity (by contrast ratio measurement) given by paint films of white or light colours of tristimulus value <i>Y</i> greater than 25, applied at a spreading rate of 20 m²/l to a black and white chart or to colourles

12884,IS,,ISO 6505:1984,"Rubber, vulcanized — Determination of adhesion to, and corrosion of, metals",Caoutchouc vulcanisé — Détermination de l'adhérence aux métaux et de la corrosion des métaux,1984-12-01,1,['83.060'],ISO/TC 45/SC 2,9599,,[2282],"['en','fr']",4,

2282,IS,,ISO 6505:1997,"Rubber, vulcanized or thermoplastic — Determination of tendency to adhere to and to corrode metals",Caoutchouc vulcanisé ou thermoplastique — Détermination de la tendance à adhérer sur les métaux et à corroder les métaux,1997-06-12,2,['83.060'],ISO/TC 45/SC 2,9599,[12884],[36982],"['en','fr']",6,

36982,IS,,ISO 6505:2005,"Rubber, vulcanized or thermoplastic — Determination of tendency to adhere to and corrode metals","Caoutchouc, vulcanisé ou thermoplastique — Détermination de la tendance à adhérer aux métaux et à les corroder",2005-10-03,3,['83.060'],ISO/TC 45/SC 2,9599,[2282],[65922],"['en','fr']",13,<p>ISO 6505:2005 specifies a method for the determination of the tendency of vulcanized or thermoplastic rubbers to adhere to and to corrode metals when exposed to a specified test environment.</p>

65922,IS,,ISO 6505:2015,"Rubber, vulcanized or thermoplastic — Determination of tendency to adhere to and corrode metals","Caoutchouc, vulcanisé ou thermoplastique — Détermination de la tendance à adhérer aux métaux et à les corroder",2015-03-16,4,['83.060'],ISO/TC 45/SC 2,9599,[36982],[82443],"['en','fr']",12,<p>ISO 6505:2015 specifies a method for the determination of the tendency of vulcanized or thermoplastic rubbers to adhere to and to corrode metals when exposed to a specified test environment.</p>

27572,IS,,ISO 6506-1:1999,Metallic materials — Brinell hardness test — Part 1: Test method,Matériaux métalliques — Essai de dureté Brinell — Partie 1: Méthode d'essai,1999-09-16,1,['77.040.10'],ISO/TC 164/SC 3,9599,"[4417,12885]","[37742,37739]","['en','fr']",16,

37739,IS,,ISO 6506-1:2005,Metallic materials — Brinell hardness test — Part 1: Test method,Matériaux métalliques — Essai de dureté Brinell — Partie 1: Méthode d'essai,2005-12-06,2,['77.040.10'],ISO/TC 164/SC 3,9599,[27572],[59671],"['en','fr']",15,<p>ISO 6506-1:2005 specifies the method for the Brinell hardness test for metallic materials and is applicable up to the limit of 650 HBW.</p>

12885,IS,,ISO 6506:1981,Metallic materials — Hardness test — Brinell test,Matériaux métalliques — Essai de dureté — Essai Brinell,1981-09-01,1,['77.040.10'],ISO/TC 164/SC 3,9599,"[3729,4041,4403]",[27572],"['en','fr']",4,

27573,IS,,ISO 6506-2:1999,Metallic materials — Brinell hardness test — Part 2: Verification and calibration of testing machines,Matériaux métalliques — Essai de dureté Brinell — Partie 2: Vérification et étalonnage des machines d'essai,1999-09-16,1,['77.040.10'],ISO/TC 164/SC 3,9599,[3986],[37740],"['en','fr']",6,

37740,IS,,ISO 6506-2:2005,Metallic materials — Brinell hardness test — Part 2: Verification and calibration of testing machines,Matériaux métalliques — Essai de dureté Brinell — Partie 2: Vérification et étalonnage des machines d'essai,2005-12-06,2,['77.040.10'],ISO/TC 164/SC 3,9599,[27573],[59681],"['en','fr']",13,"<p>ISO 6506-2:2005 specifies a method of verification and calibration of testing machines used for determining Brinell hardness in accordance with ISO 6506-1.</p><p>ISO 6506-2:2005 specifies a direct method for checking the main functions of machine operation and an indirect method suitable for the overall checking of the machine. The indirect method may be used independently for

59681,IS,,ISO 6506-2:2014,Metallic materials — Brinell hardness test — Part 2: Verification and calibration of testing machines,Matériaux métalliques — Essai de dureté Brinell — Partie 2: Vérification et étalonnage des machines d'essai,2014-09-25,3,['77.040.10'],ISO/TC 164/SC 3,9599,[37740],[69774],"['en','fr']",15,"<p>ISO 6506-2:2014 specifies methods of direct and indirect verification of testing machines used for determining Brinell hardness in accordance with ISO 6506‑1, and also specifies when these two types of verification has to be performed.</p><p>The direct verification involves checking that individual machine performance parameters fall within specified limits whereas the indirec

27574,IS,,ISO 6506-3:1999,Metallic materials — Brinell hardness test — Part 3: Calibration of reference blocks,Matériaux métalliques — Essai de dureté Brinell — Partie 3: Étalonnage des blocs de référence,1999-09-16,1,['77.040.10'],ISO/TC 164/SC 3,9599,[4960],[37741],"['en','fr']",4,

37741,IS,,ISO 6506-3:2005,Metallic materials — Brinell hardness test — Part 3: Calibration of reference blocks,Matériaux métalliques — Essai de dureté Brinell — Partie 3: Étalonnage des blocs de référence,2005-12-06,2,['77.040.10'],ISO/TC 164/SC 3,9599,[27574],[59682],"['en','fr']",9,<p>ISO 6506-3:2005 specifies a method for the calibration of reference blocks to be used for use in the indirect verification of Brinell hardness testing machines as described in ISO 6506-2.</p>

37742,IS,,ISO 6506-4:2005,Metallic materials — Brinell hardness test — Part 4: Table of hardness values,Matériaux métalliques — Essai de dureté Brinell — Partie 4: Tableau des valeurs de dureté,2005-12-06,1,['77.040.10'],ISO/TC 164/SC 3,9599,[27572],[59684],"['en','fr']",12,<p>ISO 6506-4:2005 gives a table of the Brinell hardness values for use in tests on flat surfaces.</p>

12886,IS,,ISO 6507-1:1982,Metallic materials — Hardness test — Vickers test — Part 1: HV 5 to HV 100,Matériaux métalliques — Essai de dureté — Essai Vickers — Partie 1: HV 5 à HV 100,1982-07-01,1,['77.040.10'],ISO/TC 164/SC 3,9599,"[4042,3731,4399]",[24832],"['en','fr']",6,

24832,IS,,ISO 6507-1:1997,Metallic materials — Vickers hardness test — Part 1: Test method,Matériaux métalliques — Essai de dureté Vickers — Partie 1: Méthode d'essai,1997-11-20,2,['77.040.10'],ISO/TC 164/SC 3,9599,"[4414,12887,4415,4416,12888,12886]","[37746,37749]","['en','fr']",107,

37746,IS,,ISO 6507-1:2005,Metallic materials — Vickers hardness test — Part 1: Test method,Matériaux métalliques — Essai de dureté Vickers — Partie 1: Méthode d'essai,2005-12-08,3,['77.040.10'],ISO/TC 164/SC 3,9599,[24832],[64065],"['en','fr']",19,"<p>ISO 6507-1:2005 specifies the Vickers hardness test method for the three different ranges of test force for metallic materials.</p><p>The Vickers hardness test is specified in ISO 6507-1:2005 for lengths of indentation diagonals between 0,020 mm and 1,400 mm.</p>"

64065,IS,,ISO 6507-1:2018,Metallic materials — Vickers hardness test — Part 1: Test method,Matériaux métalliques — Essai de dureté Vickers — Partie 1: Méthode d'essai,2018-01-10,4,['77.040.10'],ISO/TC 164/SC 3,9599,[37746],"[83897,83898]","['en','fr']",30,<p>ISO 6507-1:2018 specifies the Vickers hardness test method for the three different ranges of test force for metallic materials including hardmetals and other cemented carbides.</p>

12887,IS,,ISO 6507-2:1983,"Metallic materials — Hardness test — Vickers test — Part 2: HV 0,2 to less than HV 5","Matériaux métalliques — Essai de dureté — Essai Vickers — Partie 2: HV 0,2 à HV 5 exclu",1983-09-01,1,['77.040.10'],ISO/TC 164/SC 3,9599,,[24832],"['en','fr']",6,

24833,IS,,ISO 6507-2:1997,Metallic materials — Vickers hardness test — Part 2: Verification of testing machines,Matériaux métalliques — Essai de dureté Vickers — Partie 2: Vérification des machines d'essai,1997-11-20,2,['77.040.10'],ISO/TC 164/SC 3,9599,"[3975,3974]",[37747],"['en','fr']",10,

37747,IS,,ISO 6507-2:2005,Metallic materials — Vickers hardness test — Part 2: Verification and calibration of testing machines,Matériaux métalliques — Essai de dureté Vickers — Partie 2: Vérification et étalonnage des machines d'essai,2005-12-08,3,['77.040.10'],ISO/TC 164/SC 3,9599,[24833],[64066],"['en','fr']",16,<p>ISO 6507-2:2005 specifies a method of verification of testing machines for determining Vickers hardness in accordance with ISO 6507-1. </p>

12888,IS,,ISO 6507-3:1989,"Metallic materials — Hardness test — Vickers test — Part 3: Less than HV 0,2","Matériaux métalliques — Essai de dureté — Essai Vickers — Partie 3: Inférieure à HV 0,2",1989-10-26,1,['77.040.10'],ISO/TC 164/SC 3,9599,,[24832],"['en','fr']",5,

24834,IS,,ISO 6507-3:1997,Metallic materials — Vickers hardness test — Part 3: Calibration of reference blocks,Matériaux métalliques — Essai de dureté Vickers — Partie 3: Étalonnage des blocs de référence,1997-11-20,2,['77.040.10'],ISO/TC 164/SC 3,9599,"[4770,4769]",[37748],"['en','fr']",5,

37748,IS,,ISO 6507-3:2005,Metallic materials — Vickers hardness test — Part 3: Calibration of reference blocks,Matériaux métalliques — Essai de dureté Vickers — Partie 3: Étalonnage des blocs de référence,2005-12-08,3,['77.040.10'],ISO/TC 164/SC 3,9599,[24834],[64067],"['en','fr']",9,"<p>ISO 6507-3:2005 specifies a method for the calibration of reference blocks to be used for the indirect verification of Vickers hardness testing machines, as specified in ISO 6507-2.</p><p>The method is applicable only for indentations with diagonals greater than or equal to 0,020 mm.</p>"

37749,IS,,ISO 6507-4:2005,Metallic materials — Vickers hardness test — Part 4: Tables of hardness values,Matériaux métalliques — Essai de dureté Vickers — Partie 4: Tableaux des valeurs de dureté,2005-12-08,1,['77.040.10'],ISO/TC 164/SC 3,9599,[24832],[64068],"['en','fr']",82,<p>ISO 6507-4:2005 gives tables of Vickers hardness for use in tests made on flat surfaces.</p>

26047,IS,,ISO 6508-1:1999,"Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T)","Matériaux métalliques — Essai de dureté Rockwell — Partie 1: Méthode d'essai (échelles A, B, C, D, E, F, G, H, K, N, T)",1999-09-09,1,['77.040.10'],ISO/TC 164/SC 3,9599,"[12889,5496]",[37743],"['en','fr']",15,

37743,IS,,ISO 6508-1:2005,"Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T)","Matériaux métalliques — Essai de dureté Rockwell — Partie 1: Méthode d'essai (échelles A, B, C, D, E, F, G, H, K, N, T)",2005-12-09,2,['77.040.10'],ISO/TC 164/SC 3,9599,[26047],[59686],"['en','fr']",24,<p>ISO 6508-1:2005 specifies the method for Rockwell and Rockwell superficial hardness tests for metallic materials.</p>

59686,IS,,ISO 6508-1:2015,Metallic materials — Rockwell hardness test — Part 1: Test method,Matériaux métalliques — Essai de dureté Rockwell — Partie 1: Méthode d'essai,2015-02-25,3,['77.040.10'],ISO/TC 164/SC 3,9599,[37743],[70460],"['en','fr']",33,"<p>ISO 6508-1:2015 specifies the method for Rockwell regular and Rockwell superficial hardness tests (scales and applicable range of application according to Table 1) for metallic materials and is applicable to stationary and portable hardness testing machines.</p><p>For specific materials and/or products, other specific International Standards apply (for instance, ISO 3738‑1 and ISO 4498).</p><p>NOTE Attention is drawn to the fact that the us

70460,IS,,ISO 6508-1:2016,Metallic materials — Rockwell hardness test — Part 1: Test method,Matériaux métalliques — Essai de dureté Rockwell — Partie 1: Méthode d'essai,2016-08-08,4,['77.040.10'],ISO/TC 164/SC 3,9599,[59686],[84343],"['en','fr']",32,"<p>ISO 6508-1:2016 specifies the method for Rockwell regular and Rockwell superficial hardness tests for scales A, B, C, D, E, F, G, H, K, 15N, 30N, 45N, 15T, 30T, and 45T for metallic materials and is applicable to stationary and portable hardness testing machines.</p><p>For specific materials and/or products, other specific International Standards apply (for instance, ISO 3738‑1 and ISO 4498).</p>"

12889,IS,,ISO 6508:1986,Metallic materials — Hardness test — Rockwell test (scales A - B - C - D - E - F - G - H - K),Matériaux métalliques — Essai de dureté — Essai Rockwell (échelles A - B - C - D - E - F - G - H - K),1986-11-13,1,['77.040.10'],ISO/TC 164/SC 3,9599,"[7681,3730]",[26047],"['en','fr']",8,

26048,IS,,ISO 6508-2:1999,"Metallic materials — Rockwell hardness test — Part 2: Verification and calibration of testing machines (scales A, B, C, D, E, F, G, H, K, N, T)","Matériaux métalliques — Essai de dureté Rockwell — Partie 2: Vérification et étalonnage des machines d'essai (échelles A, B, C, D, E, F, G, H, K, N, T)",1999-09-16,1,['77.040.10'],ISO/TC 164/SC 3,9599,"[5576,4937]",[37744],"['en','fr']",10,

37744,IS,,ISO 6508-2:2005,"Metallic materials — Rockwell hardness test — Part 2: Verification and calibration of testing machines (scales A, B, C, D, E, F, G, H, K, N, T)","Matériaux métalliques — Essai de dureté Rockwell — Partie 2: Vérification et étalonnage des machines d'essai (échelles A, B, C, D, E, F, G, H, K, N, T)",2005-12-09,2,['77.040.10'],ISO/TC 164/SC 3,9599,[26048],[59685],"['en','fr']",18,"<p>ISO 6508-2:2005 specifies a method of verification of testing machines for determining Rockwell hardness (scales A, B, C, D, E, F, G, H, K, N, T) in accordance with ISO 6508-1.</p>"

59685,IS,,ISO 6508-2:2015,Metallic materials — Rockwell hardness test — Part 2: Verification and calibration of testing machines and indenters,Matériaux métalliques — Essai de dureté Rockwell — Partie 2: Vérification et étalonnage des machines d'essai et des pénétrateurs,2015-02-25,3,['77.040.10'],ISO/TC 164/SC 3,9599,[37744],[83888],"['en','fr']",24,"<p>ISO 6508-2:2015 specifies two separate methods of verification of testing machines (direct and indirect) for determining Rockwell hardness in accordance with ISO 6508‑1:2015, together with a method for verifying Rockwell hardness indenters.</p><p>The direct verification method is used to determine whether the main parameters associated with

26049,IS,,ISO 6508-3:1999,"Metallic materials — Rockwell hardness test — Part 3: Calibration of reference blocks (scales A, B, C, D, E, F, G, H, K, N, T)","Matériaux métalliques — Essai de dureté Rockwell — Partie 3: Étalonnage des blocs de référence (échelles A, B, C, D, E, F, G, H, K, N, T)",1999-09-02,1,['77.040.10'],ISO/TC 164/SC 3,9599,"[4840,5913]",[37745],"['en','fr']",7,

37745,IS,,ISO 6508-3:2005,"Metallic materials — Rockwell hardness test — Part 3: Calibration of reference blocks (scales A, B, C, D, E, F, G, H, K, N, T)","Matériaux métalliques — Essai de dureté Rockwell — Partie 3: Étalonnage des blocs de référence (échelles A, B, C, D, E, F, G, H, K, N, T)",2005-12-12,2,['77.040.10'],ISO/TC 164/SC 3,9599,[26049],[59687],"['en','fr']",12,"<p>ISO 6508-3:2005 specifies a method for the calibration of reference blocks to be used for the indirect verification of Rockwell hardness testing machines (scales A, B, C, D, E, F, G, H, K, N, T), as specified in ISO 6508-2.</p>"

59687,IS,,ISO 6508-3:2015,Metallic materials — Rockwell hardness test — Part 3: Calibration of reference blocks,Matériaux métalliques — Essai de dureté Rockwell — Partie 3: Étalonnage des blocs de référence,2015-02-25,3,['77.040.10'],ISO/TC 164/SC 3,9599,[37745],[83893],"['en','fr']",17,"<p>ISO 6508-3:2015 specifies a method for the calibration of reference blocks to be used for the indirect and daily verification of Rockwell hardness testing machines, as specified in ISO 6508‑2:2015.</p><p>Attention is drawn to the fact that the use of hard metal for ball indenters is considered to be the standard type of Rockwell indenter ball. Steel indenter balls can be used only when complying with ISO

12890,IS,,ISO 6509:1981,Corrosion of metals and alloys — Determination of dezincification resistance of brass,Corrosion des métaux et alliages — Détermination de la résistance à la dézincification du laiton,1981-07-01,1,['77.060'],ISO/TC 156,9599,,"[59999,63079]","['en','fr']",3,"<p>The method applies to brass exposed to frech or saline waters. May be used for control or research purposes, but the field of application is not specified. The method consists of exposure of test pieces to copper(II) chloride solution followed by microscopic examination.</p>"

4784,IS,,ISO 651:1975,Solid-stem calorimeter thermometers,Thermomètres sur tige pour calorimètres,1975-09-01,1,['17.200.20'],ISO/TC 48,9599,,[74919],"['en','fr']",4,"<p>Specifies thermometers of the mercury-in-glass solid-stem type of short range with enamel back. They are used in bomb calorimetry and for other purposes where an accurate measurement of a change of temperature is required. They are not suited for measurement of the absolute temperature because they are not provided with auxiliary scales. The requirements specify material, construction, scale, and accuracy.</p>"

12893,IS,,ISO 6512:1982,Building construction — Modular coordination — Storey heights and room heights,Construction immobilière — Coordination modulaire — Hauteurs d'étage et hauteurs de pièce,1982-02-01,1,['91.060.10'],ISO/TC 59,9599,[6421],[71507],"['en','fr']",2,<p>Specifies sizes of modular storey heights and modular room heights for all types of buildings in accordance with the principles and rules of modular coordination as laid down in ISO 2848 and ISO 6511. Gives rules for determining the sizes of vertical modular dimensions in buildings. Establishes the storey height as the generally preferred vertical modular dimension.</p>

12894,IS,,ISO 6513:1982,Building construction — Modular coordination — Series of preferred multimodular sizes for horizontal dimensions,Construction immobilière — Coordination modulaire — Séries de valeurs multimodulaires pour dimensions horizontales,1982-02-01,1,['91.010.30'],ISO/TC 59,9599,,[71507],"['en','fr']",2,<p>Specifies series of preferred multimodular sizes for horizontal dimensions in building and gives guidance for their use. Applies to buildings of all types designed in accordance with the principles and rules of modular coordination as laid down in ISO 2848.</p>

12895,IS,,ISO 6514:1982,Building construction — Modular coordination — Sub-modular increments,Construction immobilière — Coordination modulaire — Accroissements inframodulaires,1982-03-01,1,['91.010.30'],ISO/TC 59,9599,,[71507],"['en','fr']",1,<p>Establishes the values of submodular increments for use in modular coordination in buildings. Applies to the construction of buildings of all types in accordance with the principles and rules of modular coordination as laid down in ISO 2848. A submodular increment is an increment of size the value of which is a selected fraction of the basic module.</p>

12898,IS,,ISO 6517:1982,Aircraft — Containers — Base-restrained certified containers for the lower deck of high capacity aircraft,Aéronefs — Conteneurs certifiés à retenue par la base pour le pont inférieur des aéronefs à grande capacité,1982-02-01,1,['55.180.30'],ISO/TC 20/SC 9,9599,,[12899],"['en','fr']",19,

12899,IS,,ISO 6517:1992,Air cargo equipment — Base-restrained certified containers exclusively for the lower deck of high-capacity aircraft,Équipement pour le fret aérien — Conteneurs certifiés à retenue par la base pour le pont inférieur des aéronefs à grande capacité exclusivement,1992-08-12,2,['55.180.30'],ISO/TC 20/SC 9,9599,[12898],[54746],"['en','fr']",13,"<p>Covers the design, fabrication, performance and testing requirements for the containers. Basic functions of containers are the unitization of baggage, cargo or mail during ground handling and transportation, and the restraint of its contents in flight.</p>"

12900,IS,,ISO 6518-1:1980,Ignition systems — Part 1: Vocabulary,Systèmes d'allumage — Partie 1: Vocabulaire,1980-10-01,1,"['43.060.50','01.040.43']",ISO/TC 22,9599,,[21751],"['en','fr','ru']",4,

21751,IS,,ISO 6518-1:1997,Road vehicles — Ignition systems — Part 1: Vocabulary,Véhicules routiers — Systèmes d'allumage — Partie 1: Vocabulaire,1997-04-24,2,"['43.060.50','01.040.43']",ISO/TC 22,9599,[12900],[35016],"['en','fr']",10,

35016,IS,,ISO 6518-1:2002,Road vehicles — Ignition systems — Part 1: Vocabulary,Véhicules routiers — Systèmes d'allumage — Partie 1: Vocabulaire,2002-06-20,3,"['43.060.50','01.040.43']",ISO/TC 22/SC 32,9599,"[7487,21751]",[85281],"['en','fr']",12,