Withdrawn and superseded ISO standards — page 144 of 246

21769,IS,,ISO 6394:1998,Acoustics — Measurement at the operator's position of noise emitted by earth-moving machinery — Stationary test conditions,Acoustique — Mesurage du bruit émis par les engins de terrassement au poste de conduite — Conditions d'essai statiques,1998-11-19,2,"['17.140.20','53.100']",ISO/TC 43/SC 1,9599,[12729],[38482],['en'],9,

12730,IS,,ISO 6395:1988,Acoustics — Measurement of exterior noise emitted by earth-moving machinery — Dynamic test conditions,Acoustique — Mesurage du bruit émis à l'extérieur par les engins de terrassement — Conditions d'essai dynamiques,1988-09-01,1,"['17.140.20','53.100']",ISO/TC 43/SC 1,9599,,[38487],"['en','fr']",13,"<p>Describes a method for determining the noise emission in terms of the A-weigthed sound power level. Is applicable to excavators (hydraulic or rope-operated), tractors with dozer equipment, loaders, and backhoe loaders.</p>"

12731,IS,Amd,ISO 6395:1988/Amd 1:1996,Acoustics — Measurement of exterior noise emitted by earth-moving machinery — Dynamic test conditions — Amendment 1,Acoustique — Mesurage du bruit émis à l'extérieur par les engins de terrassement — Conditions d'essai dynamiques — Amendement 1,1996-12-19,1,"['17.140.20','53.100']",ISO/TC 43/SC 1,9599,,[38487],"['en','fr']",4,<p>Contains a number of amendments regarding the wording of some clauses and adds the annex E.</p>

12732,IS,,ISO 6396:1992,Acoustics — Measurement at the operator's position of noise emitted by earth-moving machinery — Dynamic test conditions,Acoustique — Mesurage du bruit émis par les engins de terrassement au poste de conduite — Conditions d'essai dynamiques,1992-10-15,1,"['17.140.20','53.100']",ISO/TC 43/SC 1,9599,,[38488],"['en','fr']",6,"<p>Describes a method for determining in terms of the equivalent continuous A-weighted sound pressure level, while the machine is operating. Applies to the following machines: excavators, tractors with dozer equipment, loaders, backhoe loaders (excavator-loaders).</p>"

3702,IS,,ISO 64:1974,Withdrawal of ISO 64-1974,Annulation de l'ISO 64-1974,1974-05-01,1,['23.040.10'],ISO/TC 5,9599,,[9985],['en'],1,

4769,IS,,ISO 640:1984,"Metallic materials — Hardness test — Calibration of standardized blocks to be used for Vickers hardness testing machines HV 0,2 to HV 100","Matériaux métalliques — Essai de dureté — Étalonnage des blocs de référence à utiliser pour les machines d'essai de dureté Vickers HV 0,2 à HV 100",1984-11-01,1,['77.040.10'],ISO/TC 164/SC 3,9599,,[24834],"['en','fr']",3,

4770,IS,,ISO 640-2:1993,"Metallic materials — Calibration of standardized blocks to be used for Vickers hardness testing machines — Part 2: Less than HV 0,2","Matériaux métalliques — Étalonnage des blocs de référence à utiliser pour les machines d'essai de dureté Vickers — Partie 2: Inférieure à HV 0,2",1993-07-08,1,['77.040.10'],ISO/TC 164/SC 3,9599,,[24834],"['en','fr']",4,

12737,IS,,ISO 6401:1985,Plastics — Homopolymer and copolymer resins of vinyl chloride — Determination of residual vinyl chloride monomer — Gas chromatographic method,Plastiques — Résines d'homopolymères et de copolymères de chlorure de vinyle — Détermination du chlorure de vinyle monomère résiduel — Méthode par chromatographie en phase gazeuse,1985-02-14,1,['83.080.20'],ISO/TC 61/SC 5,9599,,[38253],"['en','fr']",4,"<p>Dissolution or suspension of a test portion in a suitable solvent, for example N,N-demethylacetamide, N,N-dimethylformamide, tetrahydrofurane or dichloroethane, free of any impurity with the same chromatographic retention time as vinyl chloride under the conditions of test. Det

38253,IS,,ISO 6401:2008,Plastics — Poly(vinyl chloride) — Determination of residual vinyl chloride monomer — Gas-chromatographic method,Plastiques — Poly(chlorure de vinyle) — Détermination du chlorure de vinyle monomère résiduel — Méthode par chromatographie en phase gazeuse,2008-08-21,2,['83.080.20'],ISO/TC 61/SC 5,9599,[12737],[83909],"['en','fr']",6,"<p>ISO 6401:2008 specifies a method for the determination of vinyl chloride monomer in homopolymer and copolymer resins of vinyl chloride and compounded materials. The method is based on sample dissolution and headspace gas chromatography. Concentrations of vinyl chloride in the range 0,1 mg/kg to 3,0 mg/kg can be determined.</p><p>A 'dry me

12738,IS,,ISO 6402-1:1990,"Plastics — Impact-resistant acrylonitrile/styrene moulding and extrusion materials (ASA, AES, ACS), excluding butadiene-modified materials — Part 1: Designation","Plastiques — Thermoplastiques à base d'acrylonitrile/styrène sans butadiène (ASA, AES, ACS), résistants au choc, pour moulage et extrusion — Partie 1: Désignation",1990-09-27,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[26809],"['en','fr']",5,

26809,IS,,ISO 6402-1:1997,"Plastics — Impact-resistant acrylonitrile/styrene (ASA, AES, ACS) moulding and extrusion materials, excluding butadiene-modified materials — Part 1: Designation system and basis for specifications","Plastiques — Acrylonitrile/styrène sans butadiène résistant au choc (ASA, AES, ACS) pour moulage et extrusion — Partie 1: Système de désignation et base de spécification",1997-07-03,2,['83.080.20'],ISO/TC 61/SC 9,9599,[12738],[28377],"['en','fr']",7,

28377,IS,,ISO 6402-1:2001,"Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 1: Designation system and basis for specifications","Plastiques — Matériaux pour moulage et extrusion à base d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile-(éthylène-propylène-diène)-styrène (AEPDS) et d'acrylonitrile-(polyéthylène chloré)-styrène (ACS) — Partie 1: Système de désignation et base de spécifications",2001-02-08,3,['83.080.20'],ISO/TC 61/SC 9,9599,[26809],[33998],"['en','fr']",8,

33998,IS,,ISO 6402-1:2002,"Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 1: Designation system and basis for specifications","Plastiques — Matériaux pour moulage et extrusion à base d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile-(éthylène-propylène-diène)-styrène (AEPDS) et d'acrylonitrile-(polyéthylène chloré)-styrène (ACS) — Partie 1: Système de désignation et base de spécifications",2002-10-10,4,['83.080.20'],ISO/TC 61/SC 9,9599,[28377],[63849],"['en','fr']",8,"<p><b>1.1 </b>ISO 6402-1:2002 establishes a system of designati

12739,IS,,ISO 6402-2:1994,"Plastics — Impact-resistant acrylonitrile/styrene (ASA, AES, ACS) moulding and extrusion materials, excluding butadiene-modified materials — Part 2: Preparation of test specimens and determination of properties","Plastiques — Thermoplastiques à base d'acrylonitrile/styrène sans butadiène (ASA, AES, ACS), résistants au choc, pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés",1994-10-20,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[33336],"['en','fr']",6,"<p>Lays down the methods of preparation of test specimens and the test methods to be used in determining the properties of ASA, AES, ACS moulding and extrusion materials. Give

33336,IS,,ISO 6402-2:2003,"Plastics — Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties","Plastiques — Matériaux pour moulage et extrusion à base d'acrylonitrile-styrène-acrylate (ASA), d'acrylonitrile-(éthylène-propylène-diène)-styrène (AEPDS) et d'acrylonitrile-(polyéthylène chloré)-styrène (ACS) — Partie 2: Préparation des éprouvettes et détermination des propriétés",2003-11-28,2,['83.080.20'],ISO/TC 61/SC 9,9599,[12739],"[53030,70488]","['en','fr']",7,"<p>ISO 6402-2:2003 specifies

12741,IS,,ISO 6404:1985,Hydraulic fluid power — Servovalves — Test methods,Transmissions hydrauliques — Servodistributeurs — Méthodes d'essai,1985-12-18,1,['23.100.50'],ISO/TC 131/SC 8,9599,,"[22770,1757]","['en','fr']",23,

12743,IS,,ISO 6405-1:1991,Earth-moving machinery — Symbols for operator controls and other displays — Part 1: Common symbols,Engins de terrassement — Symboles pour les commandes de l'opérateur et autres indications — Partie 1: Symboles communs,1991-11-28,1,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,[12742],[30310],"['en','fr']",30,<p>Gives 140 symbols which are presented with 32 % of original size and defines the various colours to be used. This first edition cancels and replaces ISO 6405:1982.</p>

24231,IS,Amd,ISO 6405-1:1991/Amd 1:1997,Earth-moving machinery — Symbols for operator controls and other displays — Part 1: Common symbols — Amendment 1: Common symbols,Engins de terrassement — Symboles pour les commandes de l'opérateur et autres indications — Partie 1: Symboles communs — Amendement 1: Symboles supplémentaires,1997-11-20,1,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,,[30310],"['en','fr']",9,

28706,IS,Amd,ISO 6405-1:1991/Amd 2:1999,Earth-moving machinery — Symbols for operator controls and other displays — Part 1: Common symbols — Amendment 2: Additional symbols,Engins de terrassement — Symboles pour les commandes de l'opérateur et autres indications — Partie 1: Symboles communs — Amendement 2: Symboles supplémentaires,1999-05-06,1,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,,[30310],"['en','fr']",2,

30310,IS,,ISO 6405-1:2004,Earth-moving machinery — Symbols for operator controls and other displays — Part 1: Common symbols,Engins de terrassement — Symboles pour les commandes de l'opérateur et autres indicateurs — Partie 1: Symboles communs,2004-11-12,2,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,"[28706,12743,24231]","[68551,60308]","['en','fr']",38,<p>ISO 6405-1:2004 establishes the common symbols for use on operator controls and other displays on earth-moving machinery as defined in ISO 6165. It is also applicable to other types of self-propelled work machines designed to operate off public roads.</p>

54417,IS,Amd,ISO 6405-1:2004/Amd 1:2010,Earth-moving machinery — Symbols for operator controls and other displays — Part 1: Common symbols — Amendment 1: Additional symbols,Engins de terrassement — Symboles pour les commandes de l'opérateur et autres indicateurs — Partie 1: Symboles communs — Amendement 1: Symboles supplémentaires,2010-12-10,2,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,,"[68551,60308]","['en','fr']",2,

12742,IS,,ISO 6405:1982,Earth-moving machinery — Symbols — Operator controls and others,Engins de terrassement — Symboles pour les commandes et autres,1982-06-01,1,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,,[12743],"['en','fr']",13,

12744,IS,,ISO 6405-2:1993,"Earth-moving machinery — Symbols for operator controls and other displays — Part 2: Specific symbols for machines, equipment and accessories","Engins de terrassement — Symboles pour les commandes de l'opérateur et autres indications — Partie 2: Symboles spécifiques aux engins, équipements et accessoires",1993-12-16,1,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,,"[60305,68552]","['en','fr']",34,"<p>Establishes 142 symbols uniquely for use on operator controls and other displays on earth-moving machinery as defined in ISO 6165. The symbols given apply to controls and displays specific to backhoe loaders, dozers, loaders, graders, scrapers, excavators and dumpers, a

24232,IS,Amd,ISO 6405-2:1993/Amd 1:1997,"Earth-moving machinery — Symbols for operator controls and other displays — Part 2: Specific symbols for machines, equipment and accessories — Amendment 1","Engins de terrassement — Symboles pour les commandes de l'opérateur et autres indications — Partie 2: Symboles spécifiques aux engins, équipements et accessoires — Amendement 1",1997-08-14,1,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,,"[60305,68552]","['en','fr']",12,

33825,IS,Amd,ISO 6405-2:1993/Amd 2:2004,"Earth-moving machinery — Symbols for operator controls and other displays — Part 2: Specific symbols for machines, equipment and accessories — Amendment 2: Additional symbols","Engins de terrassement — Symboles pour les commandes de l'opérateur et autres indications — Partie 2: Symboles spécifiques aux engins, équipements et accessoires — Amendement 2: Symboles supplémentaires",2004-12-02,1,"['01.080.20','53.100']",ISO/TC 127/SC 3,9599,,"[60305,68552]","['en','fr']",2,

12745,IS,,ISO 6406:1992,Periodic inspection and testing of seamless steel gas cylinders,Contrôle et essais périodiques des bouteilles à gaz en acier sans soudure,1992-02-19,1,['23.020.35'],ISO/TC 58/SC 4,9599,,[29921],"['en','fr']",22,"<p>Specifies the minimum requirements. Applies to cylinders intended for compressed, liquefied or dissolved gases under pressure (excluding acetylene), of water capacity from 0,5 litres up to 150 litres.</p>"

29921,IS,,ISO 6406:2005,Gas cylinders — Seamless steel gas cylinders — Periodic inspection and testing,Bouteilles à gaz — Bouteilles à gaz en acier sans soudure — Contrôles et essais périodiques,2005-02-10,2,['23.020.35'],ISO/TC 58/SC 4,9599,[12745],[61505],['en'],41,"<p>ISO 6406:2005 deals with seamless steel transportable gas cylinders (single or those that comprise a bundle) intended for compressed and liquefied gases under pressure, of water capacity from 0,5 l up to 150 l; it also applies, as far as practical, to cylinders of less than 0,5 l water capacity.</p><p>ISO 6406:2005 specifies the requirements for periodic inspection and testing to verify the integrity of such gas cylinders to

12746,IS,,ISO 6407:1992,Photography — Film dimensions — Graphic arts,Photographie — Dimensions des films arts graphiques,1992-01-23,1,"['37.040.20','37.100.20']",ISO/TC 42,9599,,"[28007,29449,30844]","['en','fr']",7,

12747,IS,,ISO 6408:1990,Photography — Paper dimensions — Rolls for photocomposition,Photographie — Dimensions des papiers — Rouleaux pour appareils de photocomposition,1990-12-20,1,"['37.040.20','37.100.20']",ISO/TC 42,9599,,[28007],"['en','fr']",7,

12749,IS,,ISO 6410:1981,Technical drawings — Conventional representation of threaded parts,Dessins techniques — Représentation conventionnelle des filetages,1981-11-01,1,['01.100.20'],ISO/TC 10,9599,[3937],"[12752,12750,12751]","['en','fr']",2,

12752,IS,,ISO 6410-3:1993,Technical drawings — Screw threads and threaded parts — Part 3: Simplified representation,Dessins techniques — Filetages et pièces filetées — Partie 3: Représentation simplifiée,1993-05-06,1,"['21.040.01','01.100.20']",ISO/TC 10/SC 6,9599,[12749],[81378],"['en','fr']",3,"<p>Establishes rules for the simplified representation of threaded parts, with the exception of screw thread inserts, which are covered in ISO 6410-2. This representation is applicable when it is not necessary to show the exact shape and details of the parts (see ISO 6410-1), e.g. in assembly drawings.</p>"

12754,IS,,ISO 6412-1:1989,Technical drawings — Simplified representation of pipelines — Part 1: General rules and orthogonal representation,Dessins techniques — Représentation simplifiée des tuyaux et lignes de tuyauteries — Partie 1: Règles générales et représentation orthogonale,1989-10-19,1,"['01.100.99','23.040.01']",ISO/TC 10/SC 10,9599,,[73352],"['en','fr']",9,<p>This part deals with rules common to orthogonal and isometric representation. Rules applicable only to isometric representation are given in part 2. All sorts of pipe materials (rigid and flexible) are covered. The figures only illustrate the text and should not be considered dessign examples Annex A contain the bibliography a

12755,IS,,ISO 6412-2:1989,Technical drawings — Simplified representation of pipelines — Part 2: Isometric projection,Dessins techniques — Représentation simplifiée des tuyaux et lignes de tuyauteries — Partie 2: Projection isométrique,1989-10-19,1,"['01.100.99','23.040.01']",ISO/TC 10/SC 10,9599,,[73353],"['en','fr']",9,"<p>This part specifies supplementary rules, in addition to the general rules given in part 1, applicable to the isometric representation which shall be used where the essential features are to be shown clearly in three dimensions (for tenders, manufacturing and erection in pipeline construction as well as in machine construction and the construction industry). For the presen

12756,IS,,ISO 6412-3:1993,Technical drawings — Simplified representation of pipelines — Part 3: Terminal features of ventilation and drainage systems,Dessins techniques — Représentation simplifiée des tuyaux et lignes de tuyauteries — Partie 3: Accessoires pour les systèmes de ventilation et de drainage,1993-01-21,1,"['01.100.99','23.040.01']",ISO/TC 10/SC 10,9599,,[73354],"['en','fr']",4,<p>Gives simplified representations for 10 terminal features. The simplified representations may be combined with graphical symbols.</p>

12757,IS,,ISO 6413:1988,Technical drawings — Representation of splines and serrations,Dessins techniques — Représentation des cannelures et des dentelures,1988-11-24,1,"['21.120.30','01.100.20']",ISO/TC 10/SC 6,9599,,[66650],"['en','fr']",5,<p>Rules and graphical symbols are given which are applicable to detail drawings of the parts (shafts and hubs) and to assembly drawings of joints. Both methods of the true and simplified representation are specifed. Annex A gives the proportions and dimensions of graphical symbols.</p>

12758,IS,,ISO 6414:1982,Technical drawings for glassware,Dessins techniques de verrerie,1982-02-01,1,['01.100.99'],ISO/TC 10/SC 6,9599,,"[74192,66651]","['en','fr']",6,<p>The rules and conventions established are intended for particular use with drawings for laboratory glassware or glassware in other technical fields. Optical parts are not included. The figures merely illustrate the text and should not be considered design examples. They are simplified and not to ecale.</p>

12759,IS,,ISO 6415:1981,Internal combustion engines — Spin-on filters for lubricating oil — Dimensions,Moteurs à combustion interne — Filtres à huile vissés — Dimensions,1981-02-01,1,['43.060.30'],ISO/TC 22,9599,,[12760],"['en','fr']",4,

12760,IS,,ISO 6415:1990,Internal combustion engines — Spin-on filters for lubricating oil — Dimensions,Moteurs à combustion interne — Filtres à huile vissés — Dimensions,1990-12-13,2,['43.060.30'],ISO/TC 22,9599,[12759],[35017],"['en','fr']",4,<p>Specifies the essential dimensions necessary for interchangeability of oil filters. Gives also the designation and marking of these filters.</p>

12761,IS,,ISO 6416:1985,Liquid flow measurement in open channels — Measurement of discharge by the ultrasonic (acoustic) method,Mesure de débit des liquides dans les canaux découverts — Mesure de débit à l'aide de la méthode ultrasonique (acoustique),1985-03-21,1,['17.120.20'],ISO/TC 113/SC 1,9599,,[12762],"['en','fr']",20,

12762,IS,,ISO 6416:1992,Measurement of liquid flow in open channels — Measurement of discharge by the ultrasonic (acoustic) method,Mesure de débit des liquides dans les canaux découverts — Mesure du débit à l'aide de la méthode ultrasonique (acoustique),1992-09-17,2,['17.120.20'],ISO/TC 113/SC 1,9599,"[12761,12763]",[34374],"['en','fr']",28,"<p>Describes the establishment and operation of an ultrasonic gauging station for the measurement of discharge in a river, an open channel, or a closed conduit with a free water surface. Is limited to the 'time of travel of acoustic pulses' technique. Annex A describes the determination of flow direction.</p>"

34374,IS,,ISO 6416:2004,Hydrometry — Measurement of discharge by the ultrasonic (acoustic) method,Hydrométrie — Mesure du débit à l'aide de la méthode ultrasonique (acoustique),2004-06-28,3,['17.120.20'],ISO/TC 113/SC 1,9599,[12762],"[62152,55742]",['en'],50,"<p>ISO 6416:2004 describes the establishment and operation of an ultrasonic (transit-time) gauging station for the continuous measurement of discharge in a river, an open channel or a closed conduit. It also describes the basic principles on which the method is based, the operation and performance of associated instrumentation and procedures for commissioning.</p><p>It is limited to the transit time of ultrasonic pulses technique, and i

12763,IS,,ISO 6418:1985,Liquid flow measurement in open channels — Ultrasonic (acoustic) velocity meters,Mesure de débit des liquides dans les canaux découverts — Compteurs ultrasoniques (acoustiques) de vitesse,1985-02-21,1,['17.120.20'],ISO/TC 113/SC 5,9599,,[12762],"['en','fr']",13,

12764,IS,,ISO 6419-1:1984,Hydrometric data transmission systems — Part 1: General,Systèmes de transmission de données hydrométriques — Partie 1: Généralités,1984-12-01,1,['17.120.20'],ISO/TC 113/SC 5,9599,,[12765],"['en','fr']",18,

4772,IS,,ISO 642:1979,Steel — Hardenability test by end quenching (Jominy test),Acier — Essai de trempabilité par trempe en bout (essai Jominy),1979-11-01,1,['77.040.99'],ISO/TC 17/SC 7,9599,,[1228],"['en','fr']",11,

1228,IS,,ISO 642:1999,Steel — Hardenability test by end quenching (Jominy test),Acier — Essai de trempabilité par trempe en bout (essai Jominy),1999-09-09,2,['77.040.99'],ISO/TC 17/SC 7,9599,[4772],"[85868,77114]","['en','fr']",18,

12768,IS,,ISO 6420:1984,Liquid flow measurement in open channels — Position fixing equipment for hydrometric boats,Mesure de débit des liquides dans les canaux découverts — Équipement de localisation de bateaux hydrométriques,1984-12-01,1,['17.120.20'],ISO/TC 113/SC 5,9599,,[65501],"['en','fr']",9,"<p>Specifies methods of determining the position of hydrometric boats with respect to known points on the banks of rivers or estuaries. Applies to conventional surveying techniques and, in recognition of the availability of more sophisticated equipment, describes the principles of operation of currently available electronic positioning equipment.</p>"

12770,IS,,ISO 6422:1985,Layout key for trade documents,Formule-cadre pour les documents commerciaux,1985-10-17,1,['01.140.30'],ISO/TC 154,9599,,[54844],"['en','fr']",4,"<p>A common description for documents relating to administrative, commercial, productive and distributive activities constituting trade irrespective whether these documents are completed in handwriting, by mechanical or automatic equipment or by reproduction. Intended particularly for the designing of alligned series of forms employing a reproducible master in a one-run method of document preparation.</p>"

12772,IS,,ISO 6425:1982,Divers' watches,Montres de plongée,1982-12-01,1,"['39.040.10','97.220.40']",ISO/TC 114/SC 3,9599,,"[12773,12774]","['en','fr']",4,

12773,IS,,ISO 6425:1984,Divers' watches,Montres de plongée,1984-05-01,2,['39.040.10'],ISO/TC 114,9599,[12772],[12774],"['en','fr']",4,

12774,IS,,ISO 6425:1996,Divers' watches,Montres de plongée,1996-07-11,3,"['39.040.10','97.220.40']",ISO/TC 114/SC 3,9599,"[12773,12772]",[66517],"['en','fr']",7,

12776,IS,,ISO 6426-2:1984,Horological vocabulary — Part 2: Technico-commercial definitions,Vocabulaire horloger — Partie 2: Définitions technico-commerciales,1984-04-01,1,"['01.040.39','39.040.01']",ISO/TC 114,9599,,"[24995,37066]","['en','fr']",19,"<p>The 136 definitions are intended more particulary to the general public and have been simplified especially with regard to rate of a time measuring instrument. They apply to time measuring instruments and related devices. In detail, the definitions are concerned with: general terms; time measuring instruments; rate of a time measuring instrument; essential devices and parts; functions, indications and additional devices; components and miscell

37066,IS,,ISO 6426-2:2002,Horological vocabulary — Part 2: Technical and commercial definitions,Vocabulaire horloger — Partie 2: Définitions technico-commerciales,2002-10-03,2,"['01.040.39','39.040.01']",ISO/TC 114/SC 9,9599,"[35283,12776]",[88512],"['en','fr']",31,<p>ISO 6426-2:2002 defines the principal technical and commercial terms used in the horological industry.</p><p>The terms and definitions apply to time-measuring instruments and related devices.</p>

54753,IS,Amd,ISO 6426-2:2002/Amd 1:2012,Horological vocabulary — Part 2: Technical and commercial definitions — Amendment 1,Vocabulaire horloger — Partie 2: Définitions technico-commerciales — Amendement 1,2012-08-08,2,"['01.040.39','39.040.01']",ISO/TC 114/SC 9,9599,,[88512],"['en','fr']",2,

38576,IS,Cor,ISO 6426-2:2002/Cor 1:2003,Horological vocabulary — Part 2: Technical and commercial definitions — Technical Corrigendum 1,Vocabulaire horloger — Partie 2: Définitions technico-commerciales — Rectificatif technique 1,2003-05-13,2,"['01.040.39','39.040.01']",ISO/TC 114/SC 9,9599,,[88512],"['en','fr']",1,

12777,IS,,ISO 6427:1982,Plastics — Determination of matter extractable by organic solvents (conventional methods),Plastiques — Détermination des matières extractibles avec des solvants organiques (méthodes conventionnelles),1982-12-01,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[12778],"['en','fr']",9,

12778,IS,,ISO 6427:1992,Plastics — Determination of matter extractable by organic solvents (conventional methods),Plastiques — Détermination des matières extractibles par des solvants organiques (Méthodes conventionnelles),1992-12-17,2,['83.080.01'],ISO/TC 61/SC 5,9599,"[4702,12777]",[62009],"['en','fr']",9,"<p>Specifies methods for the determination of components in plastics that can be extracted by hot organic liquids near their boiling point. For one special case a so-called cold extraction method is given in annex B. The extractable components can be monomers, oligomers, polymers, plasticizers, stabilizers, etc.</p>"

62009,IS,,ISO 6427:2013,Plastics — Determination of matter extractable by organic solvents (conventional methods),Plastiques — Détermination des matières extractibles par des solvants organiques (Méthodes conventionnelles),2013-01-22,3,['83.080.01'],ISO/TC 61/SC 5,9599,[12778],[88109],"['en','fr']",15,"<p>ISO 6427:2013 specifies methods for the determination of components in plastics that can be extracted by hot organic liquids near their boiling points. For one special case, a so-called cold-extraction method is given.</p><p>The extractable components can be monomers, oligomers, polymers, plasticizers, stabilizers, etc. The kind and percentage of extractable matter influence the properties

12780,IS,,ISO 6429:1983,Information processing — ISO 7-bit and 8-bit coded character sets — Additional control functions for character-imaging devices,Traitement de l'information — Jeux ISO de caractères codés à 7 et à 8 éléments — Fonctions de commande supplémentaires pour les dispositifs de visualisation de caractères,1983-05-01,1,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,"[12782,12781]","['en','fr']",37,

12781,IS,,ISO 6429:1988,Information processing — Control functions for 7-bit and 8-bit coded character sets,Traitement de l'information — Fonctions de commande pour jeux de caractères codés à 7 et à 8 éléments,1988-11-10,2,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,[12780],[12782],['en'],51,

4773,IS,,ISO 643:1983,Steels — Micrographic determination of the ferritic or austenitic grain size,Aciers — Détermination micrographique de la grosseur du grain ferritique ou austénitique des aciers,1983-09-01,1,['77.040.99'],ISO/TC 17/SC 7,9599,,[30694],"['en','fr']",27,"<p>Specifies the methods for revealing the grain and for estimating the mean size of the grain revealed. Includes a counting method (annex A) and determination of grain size by using of standard charts (annnexes B and C) taken from an AFNOR Standard and an ASTM document, respectively.</p>"

30694,IS,,ISO 643:2003,Steels — Micrographic determination of the apparent grain size,Aciers — Détermination micrographique de la grosseur de grain apparente,2003-02-06,2,['77.040.99'],ISO/TC 17/SC 7,9599,[4773],[61697],"['en','fr']",35,"<p>ISO 643 specifies a micrographic method of determining apparent ferritic or austenitic grain size in steels. It describes the methods of revealing grain boundaries and of estimating the mean grain size of specimens with unimodal size distribution.</p><p>Although grains are three-dimensional in shape, the metallographic sectioning plane can cut through a grain at any point from a grain corner, to the maximum diameter of the grain, thus producing a range of

61697,IS,,ISO 643:2012,Steels — Micrographic determination of the apparent grain size,Aciers — Détermination micrographique de la grosseur de grain apparente,2012-12-10,3,['77.040.99'],ISO/TC 17/SC 7,9599,[30694],"[72193,65406]","['en','fr']",35,"<p>ISO 643:2012 specifies a micrographic method of determining apparent ferritic or austenitic grain size in steels. It describes the methods of revealing grain boundaries and of estimating the mean grain size of specimens with unimodal size distribution. Although grains are three-dimensional in shape, the metallographic sectioning plane can cut through a grain at any point from a grain corner, to the maximum diameter of the grain, thus producing a

72193,IS,,ISO 643:2019,Steels — Micrographic determination of the apparent grain size,Aciers — Détermination micrographique de la grosseur de grain apparente,2019-12-12,4,['77.040.99'],ISO/TC 17/SC 7,9599,[61697],[82221],"['en','fr']",21,"<p>This document specifies a micrographic method of determining apparent ferritic or austenitic grain size in steels. It describes the methods of revealing grain boundaries and of estimating the mean grain size of specimens with unimodal size distribution. Although grains are three-dimensional in shape, the metallographic sectioning plane can cut through a grain at any point from a grain corner, to the maximum diameter of the grain, thus producing a range o

12783,IS,,ISO 6430:1983,Pneumatic fluid power — Single rod cylinders with integral mountings — 10 bar (1 000 kPa) series — Bores from 32 to 250 mm — Mounting dimensions,Transmissions pneumatiques — Vérins à simple tige à fixations intégrées — Série 10 bar (1 000 kPa) — Alésages de 32 à 250 mm — Dimensions de montage,1983-04-01,1,['23.100.20'],ISO/TC 131/SC 3,9599,,[12784],['en'],9,

12785,IS,,ISO 6431:1983,Pneumatic fluid power — Single rod cylinders with detachable mountings — 10 bar (1 000 kPa) series — Bores from 32 to 320 mm — Mounting dimensions,Transmissions pneumatiques — Vérins à simple tige à fixations détachables — Série 10 bar (1 000 kPa) — Alésages de 32 à 320 mm — Dimensions de montage,1983-03-01,1,['23.100.20'],ISO/TC 131/SC 3,9599,,[12786],"['en','fr']",9,

12786,IS,,ISO 6431:1992,"Pneumatic fluid power — Single rod cylinders, 1 000 kPa (10 bar) series, with detachable mountings, bores from 32 mm to 320 mm — Mounting dimensions","Transmissions pneumatiques — Vérins 1 000 kPa (10 bar) à simple tige, à fixations détachables, de diamètres d'alésage 32 mm à 320 mm — Dimensions d'interchangeabilité",1992-05-21,2,['23.100.20'],ISO/TC 131/SC 3,9599,[12785],[26284],"['en','fr']",11,"<p>Establishes a metric series of mounting dimensions (basic dimensions, nominal stroke and tolerances, bore sizes, mounting styles, piston rod characteristics) required for interchangeability of commonly used pneumatic cylinders for a maximum working pressure of 1 000 kPa

12787,IS,,ISO 6432:1985,Pneumatic fluid power — Single rod cylinders — 10 bar (1 000 kPa) series — Bores from 8 to 25 mm — Mounting dimensions,Transmissions pneumatiques — Vérins à simple tige — Série 10 bar (1 000 kPa) — Alésages de 8 à 25 mm — Dimensions de montage,1985-06-06,1,['23.100.20'],ISO/TC 131/SC 3,9599,,"[61759,64054]","['en','fr']",5,"<p>Establishes metric mounting dimensions for cylinders as required for interchangeability of commonly used hydraulic cylinders. Includes the bore sizes as follows: 8, 10, 12, 16, 20, 25 mm. Gives the following mounting styles: MR3, MP3, MS3, MF8 (tables 2 and 3, figures 2 and 3). Figure 1 and table 1 contain the basic dimensions.</p>"

12788,IS,,ISO 6433:1981,Technical drawings — Item references,Dessins techniques — Repères des éléments,1981-08-01,1,['01.100.01'],ISO/TC 10/SC 1,9599,,[51527],"['en','fr']",2,<p>General rules for application and presentation are given. In the context of this standard the purpose of item references is restricted to the identification of component parts of assemblies and/or the identification of individual items detailed in the same drawing.</p>

12794,IS,,ISO 6439:1984,Water quality — Determination of phenol index — 4-Aminoantipyrine spectrometric methods after distillation,Qualité de l'eau — Détermination de l'indice phénol — Méthode spectrométrique à l'amino-4 antipyrine après distillation,1984-06-01,1,['13.060.50'],ISO/TC 147/SC 2,9599,,[12795],"['en','fr']",7,

12796,IS,,ISO 6440:1985,"Wheelchairs — Nomenclature, terms and definitions","Fauteuils roulants — Nomenclature, termes et définitions",1985-12-12,1,"['11.180.10','01.040.11']",ISO/TC 173/SC 1,9599,,"[44224,33527]","['en','fr']",10,"<p>Definitions and illustrations of the basic elements of wheelchairs (manual, electric and any others). The dimensions commonly used to describe the wheelchair's physical characteristics are also shown. The list of accessories given is not exhaustive.</p>"

12797,IS,,ISO 6441:1984,Paints and varnishes — Indentation test (spherical or pyramidal),Peintures et vernis — Essai d'indentation (sphérique ou pyramidal),1984-08-01,1,['87.040'],ISO/TC 35/SC 9,9599,,"[26982,28783,26983]","['en','fr']",3,<p>The test method is applicable on a single or multi-coat system. The result is expressed as the depth of indentation produced when an indentor of specified or between the interested parties agreed size and shape is applied to the coating under defined conditions. The method is applicable if the identation does not exceed approximately 10 % of the total coating thickness. The indentation apparatus shall be constructed so that the contact load and the test

12798,IS,,ISO 6442:1981,Door leaves — Measurement of defects of general flatness,Vantaux de portes — Mesurage des défauts de planéité générale,1981-01-01,1,['91.060.50'],ISO/TC 162,9599,,[42855],"['en','fr']",2,

12799,IS,,ISO 6443:1980,Door leaves — Measurement of dimensions and of defects of squareness,Vantaux de portes — Mesurage des dimensions et des défauts d'équerrage,1980-12-01,1,['91.060.50'],ISO/TC 162,9599,,[42856],"['en','fr']",2,

12800,IS,,ISO 6444:1980,Door leaves — Test of behaviour under humidity variations (successive uniform climates),Vantaux de portes — Essai de comportement aux variations d'humidité (climats uniformes successifs),1980-12-01,1,['91.060.50'],ISO/TC 162,9599,,[42857],"['en','fr']",1,

12801,IS,,ISO 6445:1989,Doors and doorsets — Test of behaviour between two different climates,Portes et blocs-portes — Essai de comportement entre deux climats différents,1989-12-21,1,['91.060.50'],ISO/TC 162,9599,,[42858],"['en','fr']",3,

12803,IS,,ISO 6447:1983,Rubber seals — Joint rings used for gas supply pipes and fittings — Specification for material,Caoutchouc — Garnitures d'étanchéité pour joints de canalisations de gaz — Spécifications des matériaux,1983-10-01,1,"['83.140.50','91.140.40','75.200']",ISO/TC 45/SC 4,9599,,"[2142,40110]","['en','fr']",4,"<p>Specification refers to operating temperatures up to 50 °C. Other requirements, particularly functional tests for the actual sealing materials, shall be specified in national standards. Applicable to joint rings for all pipeline materials including iron, steel, copper, plastics. The standard does not include joint rings made from cellular rubbers or with enclosed voids

12804,IS,,ISO 6448:1985,Rubber seals — Joint rings used for petroleum product supply pipes and fittings — Specification for material,Caoutchouc — Garnitures d'étanchéité pour joints de canalisations de produits pétroliers — Spécifications des matériaux,1985-04-18,1,"['83.140.50','75.200']",ISO/TC 45/SC 4,9599,,[40110],"['en','fr']",4,"<p>Specifies requirements, but does not apply to the mentioned product with an aromatic content higher than 30 % and liquids polluted by petroleum traces. Other requirements shall be specified in national standards. Iron, steel, copper, plastics are included as pipeline materials. Not included are joint rings made of cellular rubbers. 2 tables with general and

37848,IS,,ISO 6450:2005,Rubber- or plastics-coated fabrics — Determination of resistance to liquids,Supports textiles revêtus de caoutchouc ou de plastique — Détermination de la résistance aux liquides,2005-08-26,1,['59.080.40'],ISO/TC 45/SC 4,9599,,[77553],['en'],10,"<p>ISO 6450:2005 specifies two methods (methods 1 and 2) of evaluating the resistance of fabrics coated with plastics or with vulcanized rubber to the action of liquids by measurement of selected properties of the materials before and after immersion in selected liquids.</p><p>The difference between the two methods is as follows:</p><ul><li>In method 1, excess liquid is removed from the test pieces, after immersion, by wiping.<

12808,IS,,ISO 6452:2000,Rubber- or plastics-coated fabrics — Determination of fogging characteristics of trim materials in the interior of automobiles,Supports textiles revêtus de caoutchouc ou de plastique — Détermination des caractéristiques de ternissement des matériaux constitutifs des garnitures utilisées dans l'habitacle des automobiles,2000-07-06,1,"['43.040.60','59.080.40']",ISO/TC 45/SC 4,9599,,[43716],['en'],11,

43716,IS,,ISO 6452:2007,Rubber- or plastics-coated fabrics — Determination of fogging characteristics of trim materials in the interior of automobiles,Textiles revêtus de caoutchouc ou de plastique — Détermination des caractéristiques d'embuage des matériaux de garnissage utilisés dans l'habitacle automobile,2007-05-30,2,"['43.040.60','59.080.40']",ISO/TC 45/SC 4,9599,[12808],[77554],"['en','fr']",12,"<p>ISO 6452:2007 specifies a test method which is intended to determine the fogging characteristics of rubber- or plastics-coated fabrics that are used as trim materials in the interior of motor vehicles.</p><p>The method may also be applicable to fluid, pasty, powdered or solid raw materials w

12811,IS,,ISO 6455:1983,Unplasticized polyvinyl chloride (PVC) fittings with elastic sealing ring type joints for pipes under pressure — Dimensions of laying lengths — Metric series,"Raccords en polychlorure de vinyle (PVC) non plastifié avec joints d'étanchéité élastiques, pour tubes avec pression — Dimensions de montage — Série métrique",1983-01-01,1,['23.040.45'],ISO/TC 138/SC 2,9599,,[50363],"['en','fr']",7,"<p>Specifies the series of diameters to be used and the dimensions, which are common to those types of fittings regardless their method of manufacture and composition. The current types and sizes of fittings are listed and should be used as a guide.</p>"

12812,IS,,ISO 6457:1982,Textile machinery and accessories — Heald carrying rod for 'C' shaped end loop of flat steel healds — Dimensions,Matériel pour l'industrie textile — Tringle porte-lisses pour boucle d'extrémité en forme de 'C' des lisses en acier plat — Dimensions,1982-06-01,1,['59.120.30'],ISO/TC 72/SC 3,9599,,[23977],"['en','fr']",1,

4776,IS,,ISO 646:1983,Information processing — ISO 7-bit coded character set for information interchange,Traitement de l'information — Jeu ISO de caractères codés à 7 éléments pour l'échange d'information,1983-07-01,2,['35.040.10'],ISO/IEC JTC 1/SC 2,9599,,[4777],['en'],15,

43294,IS,,ISO 6460-1:2007,Motorcycles — Measurement method for gaseous exhaust emissions and fuel consumption — Part 1: General test requirements,Motocycles — Méthode de mesure des émissions de gaz d'échappement et de la consommation de carburant — Partie 1: Exigences générales d'essai,2007-07-30,1,"['13.040.50','43.140']",ISO/TC 22/SC 38,9599,"[12815,20174]",[76925],['en'],51,"<p>ISO 6460-1:2007 specifies the general test requirements for measurement for the gaseous exhaust emissions from motorcycles, and for determining the fuel consumption of motorcycles as defined in ISO 3833. It is applicable to motorcycles equipped with a spark ignition engine (4-stroke engine, 2-stroke engine or rotar

65507,IS,Amd,ISO 6460-1:2007/Amd 1:2015,Motorcycles — Measurement method for gaseous exhaust emissions and fuel consumption — Part 1: General test requirements — Amendment 1,Motocycles — Méthode de mesure des émissions de gaz d'échappement et de la consommation de carburant — Partie 1: Exigences générales d'essai — Amendement 1,2015-11-06,1,"['13.040.50','43.140']",ISO/TC 22/SC 38,9599,,[76925],['en'],1,

12815,IS,,ISO 6460:1981,Road vehicles — Measurement method of gaseous pollutants emitted by motorcycles equipped with a controlled ignition engine,Véhicules routiers — Méthode de mesurage des émissions de gaz polluants par les motocycles équipés de moteurs à allumage commandé,1981-06-01,1,"['43.140','13.040.50']",ISO/TC 22,9599,,"[43295,43296,43294]","['en','fr']",14,"<p>Specifies methods of measurement for gaseous pollutants emitted by motorcycles as defined in ISO 3833, equipped with a 4-stroke, a 2-stroke or a rotary controlled ignition engine. Defines a driving cycle in accordance with the requirements of different types of motorcycles and provides specifications of the collecting method

43295,IS,,ISO 6460-2:2007,Motorcycles — Measurement method for gaseous exhaust emissions and fuel consumption — Part 2: Test cycles and specific test conditions,Motocycles — Méthode de mesure des émissions de gaz d'échappement et de la consommation de carburant — Partie 2: Conditions d'essai spécifiques et cycles d'essai,2007-07-23,1,"['13.040.50','43.140']",ISO/TC 22,9599,"[12815,20174]",[62685],['en'],21,"<p>ISO 6460-2:2007 defines test cycles for measurement for the gaseous emissions from motorcycles, as well as for determining the fuel consumption of motorcycles as defined in ISO 3833, equipped with a spark ignition engine (four-stroke engine, two-stroke engine or rotary piston engine) o

12820,IS,,ISO 6462:1983,Face milling cutters with indexable inserts — Dimensions,"Fraises à surfacer et à surfacer et dresser, à plaquettes amovibles — Dimensions",1983-02-01,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[44803],"['en','fr']",7,

12823,IS,,ISO 6465:1984,Whole cumin (Cuminum cyminum Linnaeus) — Specification,Cumin entier (Cuminum cyminum Linnaeus) — Spécifications,1984-05-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[40677],"['en','fr']",3,"<p>Covers the requirements for this product with regard to whole-sale purposes, describes sampling, methods of test, and packing and marking. Grades and chemical requirements are indicated in two tables. An annex includes recommandations relating to storage and transport conditions.</p>"

12825,IS,,ISO 6467:1980,Ferrovanadium — Determination of vanadium content — Potentiometric method,Ferro-vanadium — Dosage du vanadium — Méthode potentiométrique,1980-07-01,1,['77.100'],ISO/TC 132,9599,,[65347],"['en','fr']",3,"<p>The method applies to alloys having a vanadium content less than or equal to 85 % (m/m). Specifies principle, reagents, apparatus, sample, procedure, expression of results, repeatability and test report.</p>"

27116,IS,,ISO 6469-1:2001,Electric road vehicles — Safety specifications — Part 1: On-board electrical energy storage,Véhicules routiers électriques — Spécifications de sécurité — Partie 1: Stockage de l'énergie électrique à bord du véhicule,2001-11-22,1,['43.120'],ISO/TC 22,9599,,[45477],"['en','fr']",15,

45477,IS,,ISO 6469-1:2009,Electrically propelled road vehicles — Safety specifications — Part 1: On-board rechargeable energy storage system (RESS),Véhicules routiers électriques — Spécifications de sécurité — Partie 1: Système de stockage d'énergie rechargeable à bord du véhicule (RESS),2009-09-14,2,['43.120'],ISO/TC 22/SC 37,9599,[27116],[68665],"['en','fr']",9,"<p>ISO 6469-1:2009 specifies requirements for the on-board rechargeable energy storage systems (RESS) of electrically propelled road vehicles, including battery-electric vehicles (BEVs), fuel-cell vehicles (FCVs) and hybrid electric vehicles (HEVs), for the protection of persons inside and outside the vehicle and the vehicle envir

27117,IS,,ISO 6469-2:2001,Electric road vehicles — Safety specifications — Part 2: Functional safety means and protection against failures,Véhicules routiers électriques — Spécifications de sécurité — Partie 2: Mesures de sécurité fonctionelle et protection contre les défaillances,2001-11-22,1,['43.120'],ISO/TC 22,9599,,[45478],"['en','fr']",6,

45478,IS,,ISO 6469-2:2009,Electrically propelled road vehicles — Safety specifications — Part 2: Vehicle operational safety means and protection against failures,Véhicules routiers électriques — Spécifications de sécurité — Partie 2: Mesures de sécurité fonctionelle et protection contre les défaillances du véhicule,2009-09-14,2,['43.120'],ISO/TC 22/SC 37,9599,[27117],[68666],"['en','fr']",6,"<p>ISO 6469-2:2009 specifies requirements for operational safety means and protection against failures related to hazards specific to electrically propelled road vehicles, including battery-electric vehicles (BEVs), fuel-cell vehicles (FCVs) and hybrid electric vehicles (HEVs), for the protection of per

68666,IS,,ISO 6469-2:2018,Electrically propelled road vehicles — Safety specifications — Part 2: Vehicle operational safety,Véhicules routiers électriques — Spécifications de sécurité — Partie 2: Sécurité fonctionelle du véhicule,2018-01-25,3,['43.120'],ISO/TC 22/SC 37,9599,[45478],[81346],['en'],6,"<p>ISO 6469-2:2018 specifies requirements for operational safety specific to electrically propelled road vehicles, for the protection of persons inside and outside the vehicle.</p><p>NOTE 1 Relevant requirements for motorcycles and mopeds are described in ISO 13063.</p><p>ISO 6469-2:2018 does not provide comprehensive safety information for manufacturing, maintenance and repair personnel.</p>

27118,IS,,ISO 6469-3:2001,Electric road vehicles — Safety specifications — Part 3: Protection of persons against electric hazards,Véhicules routiers électriques — Spécifications de sécurité — Partie 3: Protection des personnes contre les dangers électriques,2001-11-22,1,['43.120'],ISO/TC 22,9599,,[45479],"['en','fr']",12,

38383,IS,Cor,ISO 6469-3:2001/Cor 1:2003,Electric road vehicles — Safety specifications — Part 3: Protection of persons against electric hazards — Technical Corrigendum 1,Véhicules routiers électriques — Spécifications de sécurité — Partie 3: Protection des personnes contre les dangers électriques — Rectificatif technique 1,2003-05-13,1,['43.120'],ISO/TC 22,9599,,[45479],"['en','fr']",2,

45479,IS,,ISO 6469-3:2011,Electrically propelled road vehicles — Safety specifications — Part 3: Protection of persons against electric shock,Véhicules routiers électriques — Spécifications de sécurité — Partie 3: Protection des personnes contre les chocs électriques,2011-12-05,2,['43.120'],ISO/TC 22/SC 37,9599,"[38383,27118]",[68667],"['en','fr']",14,"<p>ISO 6469-3:2011 specifies requirements for the electric propulsion systems and conductively connected auxiliary electric systems, if any, of electrically propelled road vehicles for the protection of persons inside and outside the vehicle against electric shock.</p><p>ISO 6469-3:2011 does not apply to motorcycles and vehicles not primarily

68667,IS,,ISO 6469-3:2018,Electrically propelled road vehicles — Safety specifications — Part 3: Electrical safety,Véhicules routiers électriques — Spécifications de sécurité — Partie 3: Sécurité électrique,2018-09-26,3,['43.120'],ISO/TC 22/SC 37,9599,[45479],[81746],['en'],20,"<p>This document specifies electrical safety requirements for voltage class B electric circuits of electric propulsion systems and conductively connected auxiliary electric systems of electrically propelled road vehicles.</p><p>It specifies electrical safety requirements for protection of persons against electric shock and thermal incidents.</p><p>It does not provide comprehensive safety information for manufacturing,

76885,IS,Amd,ISO 6469-3:2018/Amd 1:2020,Electrically propelled road vehicles — Safety specifications — Part 3: Electrical safety — Amendment 1: Withstand voltage test for electric power sources,Véhicules routiers électriques — Spécifications de sécurité — Partie 3: Sécurité électrique — Amendement 1: Essai de tension de tenue pour les sources d'alimentation électrique,2020-03-12,3,['43.120'],ISO/TC 22/SC 37,9599,,[81746],['en'],4,