Withdrawn and superseded ISO standards — page 143 of 246

32461,IS,Cor,ISO 6336-3:1996/Cor 1:1999,Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength — Technical Corrigendum 1,Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 3: Calcul de la résistance à la flexion en pied de dent — Rectificatif technique 1,1999-09-09,1,['21.200'],ISO/TC 60/SC 2,9599,,[36329],['en'],2,

36329,IS,,ISO 6336-3:2006,Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength,Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 3: Calcul de la résistance à la flexion en pied de dent,2006-09-04,2,['21.200'],ISO/TC 60/SC 2,9599,"[32461,12634]",[63822],"['en','fr']",42,<p>ISO 6336-3:2006 specifies the fundamental formulae for use in tooth bending stress calculations for involute external or internal spur and helical gears.</p>

51338,IS,Cor,ISO 6336-3:2006/Cor 1:2008,Calculation of load capacity of spur and helical gears — Part 3: Calculation of tooth bending strength — Technical Corrigendum 1,Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 3: Calcul de la résistance à la flexion en pied de dent — Rectificatif technique 1,2008-05-26,2,['21.200'],ISO/TC 60/SC 2,9599,,[63822],"['en','fr']",2,

12636,IS,,ISO 6336-5:1996,Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials,Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 5: Résistance et qualité des matériaux,1996-06-13,1,['21.200'],ISO/TC 60/SC 2,9599,,[32503],"['en','fr']",34,<p>Describes contact and tooth-root stresses and gives numerical values for both limit stress numbers.</p>

32503,IS,,ISO 6336-5:2003,Calculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials,Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 5: Résistance et qualité des matériaux,2003-06-27,2,['21.200'],ISO/TC 60/SC 2,9599,[12636],[55353],"['en','fr']",43,"<p>ISO 6336-5:2003 describes contact and tooth-root stresses, and gives numerical values for both limit stress numbers. It specifies requirements for material quality and heat treatment and comments on their influences on both limit stress numbers. Values in accordance with it are suitable for use with the calculation procedures provided in ISO 6336-2 an

38788,IS,,ISO 6336-6:2006,Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load,Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 6: Calcul de la durée de vie en service sous charge variable,2006-08-14,1,['21.200'],ISO/TC 60/SC 2,9599,[18564],[63823],"['en','fr']",24,"<p>ISO 6336-6:2006 specifies the information and standardized conditions necessary for the calculation of the service life (or safety factors for a required life) of gears subject to variable loading. While the method is presented in the context of ISO 6336 and calculation of the load capacity of spur and helical gears

46474,IS,Cor,ISO 6336-6:2006/Cor 1:2007,Calculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load — Technical Corrigendum 1,Calcul de la capacité de charge des engrenages cylindriques à dentures droite et hélicoïdale — Partie 6: Calcul de la durée de vie en service sous charge variable — Rectificatif technique 1,2007-07-23,1,['21.200'],ISO/TC 60/SC 2,9599,,[63823],"['en','fr']",1,

12638,IS,,ISO 6340:1995,Water quality — Detection and enumeration of Salmonella,Qualité de l'eau — Recherche et dénombrement de Salmonella,1995-11-23,1,['07.100.20'],ISO/TC 147/SC 4,9599,,"[43448,34079]","['en','fr']",11,"<p>Specifies a method for the detection of Salmonella in water samples for monitoring purposes. Applicable to all kinds of water, except raw sewage.</p>"

12639,IS,,ISO 6341:1982,"Water quality — Determination of the inhibition of the mobility of Daphnia magna Straus (Cladocera, Crustacea)","Qualité de l'eau — Détermination de l'inhibition de la mobilité de Daphnia magna Straus (Cladocera, Crustacea)",1982-03-01,1,['13.060.70'],ISO/TC 147/SC 5,9599,,[12640],['en'],9,

12640,IS,,ISO 6341:1989,"Water quality — Determination of the inhibition of the mobility of Daphnia magna Straus (Cladocera, Crustacea)","Qualité de l'eau — Détermination de l'inhibition de la mobilité de Daphnia magna Straus (Cladocera, Crustacea)",1989-09-21,2,['13.060.01'],ISO/TC 147/SC 5,9599,[12639],[21923],"['en','fr']",7,

21923,IS,,ISO 6341:1996,"Water quality — Determination of the inhibition of the mobility of Daphnia magna Straus (Cladocera, Crustacea) — Acute toxicity test","Qualité de l'eau — Détermination de l'inhibition de la mobilité de Daphnia magna Straus (Cladocera, Crustacea) — Essai de toxicité aiguë",1996-03-07,3,['13.060.70'],ISO/TC 147/SC 5,9599,[12640],[54614],"['en','fr']",9,"<p>Describes a method for the determination of the acute toxicity to Daphnia magna Straus (Cladocera, Crustacea) of chemical substances which are soluble under the conditions of test or can be maintained as a stable suspension or dispersion, treated or untreated sewage effluents, surface or ground waters. Replaces the s

30429,IS,Cor,ISO 6341:1996/Cor 1:1998,"Water quality — Determination of the inhibition of the mobility of Daphnia magna Straus (Cladocera, Crustacea) — Acute toxicity test — Technical Corrigendum 1","Qualité de l'eau — Détermination de l'inhibition de la mobilité de Daphnia magna Straus (Cladocera, Crustacea) — Essai de toxicité aiguë — Rectificatif technique 1",1998-06-04,3,['13.060.70'],ISO/TC 147/SC 5,9599,,[54614],"['en','fr']",1,

12641,IS,,ISO 6342:1993,Micrographics — Aperture cards — Method of measuring thickness of buildup area,Micrographie — Cartes à fenêtre — Méthode de mesurage de la zone de surépaisseur,1993-08-05,1,['37.080'],ISO/TC 171/SC 2,9599,,[35521],"['en','fr']",3,<p>The method specified determines the buildup thickness of the aperture card as the difference between the thickness of the buildup area and the thickness of the card both measured using a micrometer.</p>

12643,IS,,ISO 6344-1:1998,Coated abrasives — Grain size analysis — Part 1: Grain size distribution test,Abrasifs appliqués — Granulométrie — Partie 1: Contrôle de la distribution granulométrique,1998-04-09,1,['25.100.70'],ISO/TC 29/SC 5,9599,,"[78220,78219]","['en','fr']",6,

12644,IS,,ISO 6344-2:1998,Coated abrasives — Grain size analysis — Part 2: Determination of grain size distribution of macrogrits P12 to P220,Abrasifs appliqués — Granulométrie — Partie 2: Détermination de la distribution granulométrique des macrograins P12 à P220,1998-04-16,1,['25.100.70'],ISO/TC 29/SC 5,9599,,[78220],"['en','fr']",10,

12645,IS,,ISO 6344-3:1998,Coated abrasives — Grain size analysis — Part 3: Determination of grain size distribution of microgrits P240 to P2500,Abrasifs appliqués — Granulométrie — Partie 3: Détermination de la distribution granulométrique des micrograins P240 à P2500,1998-05-28,1,['25.100.70'],ISO/TC 29/SC 5,9599,,"[56010,54164]","['en','fr']",9,

31106,IS,Cor,ISO 6344-3:1998/Cor 1:1999,Coated abrasives — Grain size analysis — Part 3: Determination of grain size distribution of microgrits P240 to P2500 — Technical Corrigendum 1,Abrasifs appliqués — Granulométrie — Partie 3: Détermination de la distribution granulométrique des micrograins P240 à P2500 — Rectificatif technique 1,1999-03-11,1,['25.100.70'],ISO/TC 29/SC 5,9599,,"[56010,54164]",['en'],1,

56010,IS,,ISO 6344-3:2013,Coated abrasives — Grain size analysis — Part 3: Determination of grain size distribution of microgrits P240 to P2500,Abrasifs appliqués — Granulométrie — Partie 3: Détermination de la distribution granulométrique des micrograins P240 à P2500,2013-05-08,2,['25.100.70'],ISO/TC 29/SC 5,9599,"[12645,31106]",[78219],"['en','fr']",25,<p>ISO 6344:2013 specifies a method for determining or testing the grain size distribution of electro-fused aluminium oxide and silicon carbide microgrits P240 to P2500 for coated abrasives as defined in ISO 6344-1.</p><p>It applies both to those grits used in the manufacture of coated abrasive products and to those grits taken from products

12647,IS,,ISO 6346:1981,"Freight containers — Coding, identification and marking","Conteneurs pour le transport de marchandises — Codage, identification et marquage",1981-09-01,1,['55.180.10'],ISO/TC 104,9599,,[12648],['en'],28,

12648,IS,,ISO 6346:1984,"Freight containers — Coding, identification and marking","Conteneurs pour le transport de marchandises — Codage, identification et marquage",1984-08-01,2,['55.180.10'],ISO/TC 104,9599,"[12647,5125,7685]",[20453],"['en','fr']",30,

12649,IS,Amd,ISO 6346:1984/Amd 1:1988,"Freight containers — Coding, identification and marking — Amendment 1","Conteneurs pour le transport de marchandises — Codage, identification et marquage — Amendement 1",1988-02-04,2,['55.180.10'],ISO/TC 104,9599,,[20453],['en'],10,

20453,IS,,ISO 6346:1995,"Freight containers — Coding, identification and marking","Conteneurs pour le transport de marchandises — Codage, identification et marquage",1995-11-23,3,['55.180.10'],ISO/TC 104/SC 4,9599,"[12648,12649]","[30196,83558,40805,55522]","['en','fr']",23,"<p>Provides a system for general application for the identification and presentation of information about freight containers. Specifies a identification system with mandatory marks for visual interpretation and optional features for automatic identification and electronic data interchange and a coding system for data on container size and type. Replaces the second edition, which has been technically revised.</p>"

59778,IS,Amd,ISO 6346:1995/Amd 3:2012,"Freight containers — Coding, identification and marking — Amendment 3","Conteneurs pour le transport de marchandises — Codage, identification et marquage — Amendement 3",2012-11-26,3,['55.180.10'],ISO/TC 104/SC 4,9599,,[83558],"['en','fr']",5,

12650,IS,,ISO 6347:1989,Textile floor coverings — Consumer information,Revêtements de sol textiles — Information du consommateur,1989-11-09,1,['97.150'],ISO/TC 219,9599,,[34167],"['en','fr']",4,"<p>Applicable to textile floor coverings of all types. Specifies the technical matters forming the basis for the provision of information, at the point of sale, for the guidance of the consumer prior to and after the purchase of a textile floor covering. This information shall be provided with the textile floor coverings at all stages from manufacturer to consumer.</p>"

34167,IS,,ISO 6347:2004,Textile floor coverings — Consumer information,Revêtements de sol textiles — Information du consommateur,2004-09-03,2,['97.150'],ISO/TC 219,9599,[12650],[66731],['en'],4,"<p>ISO 6347:2004 specifies the technical subjects that form the basis for the provision of information, at the point of sale, for the guidance of the consumer prior to and after the purchase of a textile floor covering. It is applicable to textile floor coverings of all types.</p>"

12652,IS,,ISO 6349:1979,Gas analysis — Preparation of calibration gas mixtures — Permeation method,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthode par perméation,1979-12-01,1,['71.040.40'],ISO/TC 158,9599,,[25916],"['en','fr']",6,"<p>Describes the principles of the method, which is a continuous dynamic method, for the preparation of gas mixtures in which the components that is desired to use generally have a concentration between 10-9 and 10-5 (by volume) with an achievable accuracy of 2 % of the concentration of the component.</p>"

12660,IS,,ISO 6354:1982,Adhesives — Vocabulary,Adhésifs — Vocabulaire,1982-05-01,1,"['01.040.83','83.180']",ISO/TC 61/SC 1,9599,,[4501],"['en','fr']",7,

12661,IS,,ISO 6355:1988,Textile glass — Vocabulary,Verre textile — Vocabulaire,1988-08-18,2,"['59.100.10','01.040.59']",ISO/TC 61/SC 1,9599,,[4501],"['en','fr']",,

12663,IS,,ISO 6356:2000,Textile floor coverings — Assessment of static electrical propensity — Walking test,Revêtements de sol textiles — Évaluation de la propension à l'accumulation des charges électrostatiques — Essai du marcheur,2000-03-16,1,['97.150'],ISO/TC 219,9599,[12662],[46258],"['en','fr']",14,

12666,IS,,ISO 6358:1989,Pneumatic fluid power — Components using compressible fluids — Determination of flow-rate characteristics,Transmissions pneumatiques — Éléments traversés par un fluide compressible — Détermination des caractéristiques de débit,1989-09-21,1,['23.100.01'],ISO/TC 131/SC 8,9599,,"[56612,56616,56613,21631,43560]","['en','fr']",14,"<p>Specifies a method for testing components which use gases to enable their flow-characteristics under steady-state conditions to be compared. Specifies also requirements for the test installation, the test procedure, and the presentation of results. Accuracy of measurement is divided into two classes (A and B) which are explained in annex A. Ge

56613,IS,,ISO 6358-2:2013,Pneumatic fluid power — Determination of flow-rate characteristics of components using compressible fluids — Part 2: Alternative test methods,Transmissions pneumatiques — Détermination des caractéristiques de débit des composants traversés par un fluide compressible — Partie 2: Méthodes d'essai alternatives,2013-05-08,1,['23.100.01'],ISO/TC 131/SC 5,9599,"[12666,43562,43563]",[71270],"['en','fr']",43,"<p>ISO 6358-2:2013 specifies a discharge test and a charge test as alternative methods for testing pneumatic fluid power components that use compressible fluids, i.e. gases, and that have internal flow passages that can be either fixed or variable in size to determine

4761,IS,,ISO 636:1975,Withdrawal of ISO 636-1975,Annulation de l'ISO 636-1975,1975-06-01,1,['25.160.20'],ISO/TC 44,9599,,[4762],"['en','fr']",2,

4762,IS,,ISO 636:1989,"Bare solid filler rods for oxy-acetylene and tungsten inert gas arc (TIG) welding, depositing an unalloyed or low alloyed steel — Codification","Baguettes métalliques nues massives pour le soudage oxyacétylénique et le soudage à l'arc en atmosphère inerte avec électrode en tungstène (TIG), déposant un acier non allié ou faiblement allié — Codification",1989-06-15,2,['25.160.20'],ISO/TC 44/SC 3,9599,[4761],[32143],"['en','fr']",2,"<p>Establishes the identification code, which comprises symbols referring to the welding process used and the chemical composition of the filler materials. Covers also the test for chemical composition.</p>"

32143,IS,,ISO 636:2004,"Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification",Produits consommables pour le soudage — Baguettes et fils pour dépôts par soudage TIG des aciers non alliés et des aciers à grains fins — Classification,2004-05-21,3,['25.160.20'],ISO/TC 44/SC 3,9599,[4762],[64567],"['en','fr']",11,"<p>ISO 636:2004 specifies requirements for classification of rods and wires in the as-welded condition and in the post-weld heat-treated condition for tungsten inert gas welding of non-alloy and fine grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa.</p><

64567,IS,,ISO 636:2015,"Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification",Produits consommables pour le soudage — Baguettes et fils pour dépôts par soudage TIG des aciers non alliés et des aciers à grains fins — Classification,2015-11-18,4,['25.160.20'],ISO/TC 44/SC 3,9599,[32143],[72419],"['en','fr']",12,<p>ISO 636:2015 specifies requirements for classification of rods and wires in the as-welded condition and in the post-weld heat-treated condition for tungsten inert gas welding of non-alloy and fine-grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa.</p><

72419,IS,,ISO 636:2017,"Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification",Produits consommables pour le soudage — Baguettes et fils pour dépôts par soudage TIG des aciers non alliés et des aciers à grains fins — Classification,2017-05-29,5,['25.160.20'],ISO/TC 44/SC 3,9599,[64567],[86714],"['en','fr']",13,<p>ISO 636:2017 specifies requirements for classification of rods and wires in the as-welded condition and in the post-weld heat-treated condition for tungsten inert gas welding of non-alloy and fine-grain steels with a minimum yield strength of up to 500 MPa or a minimum tensile strength of up to 570 MPa.</p><

12668,IS,,ISO 6360-1:1985,Dental rotary instruments — Number coding system — Part 1: General characteristics,Instruments rotatifs dentaires — Système de codification numérique — Partie 1: Caractéristiques générales,1985-07-25,1,['11.060.20'],ISO/TC 106/SC 4,9599,,"[29757,37301,19988]","['en','fr']",20,"<p>Specification of a number coding system for all dental rotary instruments and for several accessories used with the instruments. This standard contains the terms in English, French, Russian and German and illustrates the basic form of the instruments.</p>"

12669,IS,Add,ISO 6360-1:1985/Add 1:1988,Dental rotary instruments — Number coding system — Part 1: General characteristics — Addendum 1,Instruments rotatifs dentaires — Système de codification numérique — Partie 1: Caractéristiques générales — Additif 1,1988-04-21,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[37301],"['en','fr']",3,

12671,IS,,ISO 6360-2:1986,Dental rotary instruments — Number coding system — Part 2: Shape and specific characteristics,Instruments rotatifs dentaires — Système de codification numérique — Partie 2: Forme et caractéristiques spécifiques de réalisation,1986-04-24,1,['11.060.20'],ISO/TC 106/SC 4,9599,[12670],"[37302,29767]","['en','fr']",78,"<p>Specification of a number coding system for all dental rotary instruments and for several accessories used with the instruments. This standard contains the terms in English, French, Russian and German and illustrates the basic form of the instruments.</p>"

12672,IS,Amd,ISO 6360-2:1986/Amd 1:1991,Dental rotary instruments — Number coding system — Part 2: Shape and specific characteristics — Amendment 1,Instruments rotatifs dentaires — Système de codification numérique — Partie 2: Forme et caractéristiques spécifiques de réalisation — Amendement 1,1991-06-13,1,['11.060.20'],ISO/TC 106/SC 4,9599,,"[37302,29767]","['en','fr']",21,

12675,IS,,ISO 6361-1:1986,"Wrought aluminium and aluminium alloy sheets, strips and plates — Part 1: Technical conditions for inspection and delivery","Tôles, bandes et tôles épaisses en aluminium et alliages d'aluminium corroyés — Partie 1: Conditions techniques de contrôle et de livraison",1986-11-20,1,['77.150.10'],ISO/TC 79/SC 6,9599,[11197],"[28577,51842]","['en','fr']",3,"<p>The conditions apply to flat rolled products for general engineering applications. This part of ISO 6361 specifies among other things requirements to manufacturing process, quality control, chemical composition, mechanical properties, surface finish, dimensional tolerances, conformity with standards, marking, packi

12676,IS,,ISO 6361-2:1987,"Wrought aluminium and aluminium alloy sheets, strips and plates — Part 2: Mechanical properties","Tôles, bandes et tôles épaisses en aluminium et alliages d'aluminium corroyés — Partie 2: Caractéristiques mécaniques",1987-08-13,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[12677],"['en','fr']",,

12677,IS,,ISO 6361-2:1990,"Wrought aluminium and aluminium alloy sheets, strips and plates — Part 2: Mechanical properties","Tôles, bandes et tôles épaisses en aluminium et alliages d'aluminium corroyés — Partie 2: Caractéristiques mécaniques",1990-02-01,2,['77.150.10'],ISO/TC 79/SC 6,9599,"[6927,12676]","[51843,22884]","['en','fr']",14,"<p>The mechanical properties apply to flat rolled products for general engineering applications. This part of ISO 6361 gives in the tables 1 to 20 the tensile strength, 0,2 % proof stress, percentage elongation after rupture to various materials of wrought aluminium and aluminium alloy.</p>"

51843,IS,,ISO 6361-2:2011,"Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 2: Mechanical properties","Aluminium et alliages d'aluminium corroyés — Tôles, bandes et tôles épaisses — Partie 2: Propriétés mécaniques",2011-08-12,3,['77.150.10'],ISO/TC 79/SC 6,9599,[12677],[65056],"['en','ru']",54,"<p>In conjunction with ISO 6361-1, ISO 6361-2:2011 specifies the mechanical properties of wrought aluminium and aluminium alloy sheets, strip and plates for general engineering applications.</p><p>It applies to flat-rolled products.</p><p>The chemical composition of these materials is given in ISO 6361-5.</p><p>The designations of aluminium and aluminium alloys and the temper

12678,IS,,ISO 6361-3:1985,"Wrought aluminium and aluminium alloy sheets, strips and plates — Part 3: Strips — Tolerances on shape and dimensions","Tôles, bandes et tôles épaisses en aluminium et en alliages d'aluminium corroyés — Partie 3: Bandes — Tolérances sur forme et dimensions",1985-10-24,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[51844],"['en','fr']",3,"<p>This part of ISO 6361 specifies to strips for thicknesses up to and including 6,3 mm in accordance with the definition in ISO 3134-3, tolerances on thickness, width and lateral curvature.</p>"

51844,IS,,ISO 6361-3:2011,"Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 3: Strips: Tolerances on shape and dimensions","Aluminium et alliages d'aluminium corroyés — Tôles, bandes et tôles épaisses — Partie 3: Bandes: Tolérances sur forme et dimensions",2011-08-12,2,['77.150.10'],ISO/TC 79/SC 6,9599,[12678],[65057],"['en','ru']",4,"<p>ISO 6361-3:2011 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy strip by cold-rolling for general engineering applications.</p><p>It applies to products with a thickness over 0,15 mm up to and including 16 mm.</p><p>It does not apply to semi-finished rolled products in coiled form to be subj

12679,IS,,ISO 6361-4:1988,"Wrought aluminium and aluminium alloy sheets, strips and plates — Part 4: Sheets and plates — Tolerances on form and dimensions","Tôles, bandes et tôles épaisses en aluminium et en alliages d'aluminium corroyés — Partie 4: Tôles et tôles épaisses — Tolérances sur forme et dimensions",1988-03-31,1,['77.150.10'],ISO/TC 79/SC 6,9599,[14573],[51845],"['en','fr']",9,"<p>This part of ISO 6361 specifies the tolerances on thickness, width, length, lateral curvature, flatness and squareness for sheet, according to the definition in ISO 3134-3.</p>"

51845,IS,,ISO 6361-4:2011,"Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 4: Sheets and plates: Tolerances on shape and dimensions","Aluminium et alliages d'aluminium corroyés — Tôles, bandes et tôles épaisses — Partie 4: Tôles et tôles épaisses: Tolérances sur forme et dimensions",2011-08-12,2,['77.150.10'],ISO/TC 79/SC 6,9599,[12679],[65058],"['en','ru']",12,"<p>ISO 6361-4:2011 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy sheet and plate by hot-rolling or cold-rolling for general engineering applications.</p><p>It applies to products with a thickness over 0,15 mm up to and including 203 mm.</p><p>It does not apply to

12681,IS,,ISO 6362-1:1986,"Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 1: Technical conditions for inspection and delivery","Barres, tubes et profilés filés en aluminium et alliages d'aluminium corroyés — Partie 1: Conditions techniques de contrôle et de livraison",1986-11-20,1,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,[11197],[52235],"['en','fr']",3,"<p>The conditions apply to extruded products for general engineering applications. This part of ISO 6362 specifies among other things requirements to manufacturing process, quality control, chemical composition, mechanical properties, surface finish, dimensional tolerances, conformity with standards

52235,IS,,ISO 6362-1:2012,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 1: Technical conditions for inspection and delivery","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 1: Conditions techniques de contrôle et de livraison",2012-06-22,2,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,[12681],[76705],['en'],13,"<p>This part of ISO 6362 specifies the technical conditions for inspection and delivery of wrought aluminium and</p><p>aluminium alloy rods/bars, tubes and profiles for general engineering applications.</p><p>It applies to extruded products, but does not apply to the following:</p><p>— forging stock;</p

12682,IS,,ISO 6362-2:1987,"Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 2: Mechanical properties","Barres, tubes et profilés filés en aluminium et alliages d'aluminium corroyés — Partie 2: Caractéristiques mécaniques",1987-08-13,1,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,,[12683],"['en','fr']",,

12683,IS,,ISO 6362-2:1990,"Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 2: Mechanical properties","Barres, tubes et profilés en aluminium et alliages d'aluminium corroyés — Partie 2: Caractéristiques mécaniques",1990-03-08,2,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,[12682],"[22883,52236]","['en','fr']",12,"<p>The mechanical properties apply to extruded products for general engineering applications. This part of ISO 6362 gives in the tables 1 to 16 the tensile strength, 0,2 % proof stress, elongation to various product forms.</p>"

52236,IS,,ISO 6362-2:2012,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 2: Mechanical properties","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 2: Caractéristiques mécaniques",2012-06-22,3,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,[12683],[65059],['en'],26,

65059,IS,,ISO 6362-2:2014,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 2: Mechanical properties","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 2: Caractéristiques mécaniques",2014-09-10,4,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,[52236],[76706],['en'],25,"<p>ISO 6362-2:2014 specifies the mechanical properties of wrought aluminium and aluminium alloy extruded rods/bars, tubes, and profiles for general engineering applications. It applies to extruded products.</p>"

12684,IS,,ISO 6362-3:1990,"Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 3: Extruded rectangular bars — Tolerances on dimensions and form","Barres, tubes et profilés filés en aluminium et alliages d'aluminium corroyés — Partie 3: Barres rectangulaires filées — Tolérances sur dimensions et de forme",1990-11-22,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[28995],"['en','fr']",5,

28995,IS,,ISO 6362-3:2001,"Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 3: Extruded rectangular bars — Tolerances on shape and dimensions","Barres, tubes et profilés filés en aluminium et alliages d'aluminium corroyés — Partie 3: Barres rectangulaires filées — Tolérances sur dimensions et forme",2001-03-29,2,['77.150.10'],ISO/TC 79/SC 6,9599,[12684],[52237],"['en','fr']",8,

52237,IS,,ISO 6362-3:2012,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 3: Extruded rectangular bars — Tolerances on shape and dimensions","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 3: Barres rectangulaires filées — Tolérances sur forme et dimensions",2012-06-22,3,['77.150.10'],ISO/TC 79/SC 6,9599,[28995],[76707],['en'],7,"<p>This part of ISO 6362 specifies the tolerances on dimensions and shape of wrought aluminium and aluminium</p><p>alloy extruded rectangular bars, having thicknesses in the range from 2 mm up to 240 mm and widths in the</p><p>range from 10 mm up to 600 mm.</p><p>It applies to extruded re

12685,IS,,ISO 6362-4:1988,"Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 4: Extruded profiles — Tolerances on shape and dimensions","Barres, tubes et profilés filés en aluminium et en alliages d'aluminium corroyés — Partie 4: Profilés filés — Tolérances sur forme et dimensions",1988-04-28,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[52238],"['en','fr']",8,"<p>This part of ISO 6362 specifies among other things the tolerances on cross-sectional dimensions, on lengths, on the permissible contour and angular, twist, flatness tolerances. The tolerances apply to extruded profiles with cross-sectional dimensions given by a circumscribing circle not greater than 600 mm

52238,IS,,ISO 6362-4:2012,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 4: Profiles — Tolerances on shape and dimensions","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 4: Profilés — Tolérances sur forme et dimensions",2012-06-22,2,['77.150.10'],ISO/TC 79/SC 6,9599,[12685],[76708],['en'],17,<p>This part of ISO 6362 specifies the tolerances on dimensions and shape of wrought aluminium and aluminium</p><p>alloy extruded profiles with a cross-section contained within a circumscribing circle not greater than 800 mm.</p><p>This part of ISO 6362 applies to extruded profiles for general engineering applications only.

12686,IS,,ISO 6362-5:1991,"Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 5: Extruded round, square and hexagonal bars — Tolerances on form and dimensions","Barres, tubes et profilés filés en aluminium et alliages d'aluminium corroyés — Partie 5: Barres rondes, carrées et hexagonales filées — Tolérances sur forme et dimensions",1991-12-12,1,['77.150.10'],ISO/TC 79/SC 6,9599,[13931],[28576],"['en','fr']",4,

28576,IS,,ISO 6362-5:2001,"Wrought aluminium and aluminium alloy extruded rods/bars, tubes and profiles — Part 5: Extruded round, square and hexagonal bars — Tolerances on shape and dimensions","Barres, tubes et profilés filés en aluminium et alliages d'aluminium corroyés — Partie 5: Barres rondes, carrées et hexagonales filées — Tolérances sur dimensions et forme",2001-04-12,2,['77.150.10'],ISO/TC 79/SC 6,9599,[12686],[52239],"['en','fr']",7,

52239,IS,,ISO 6362-5:2012,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 5: Round, square and hexagonal bars — Tolerances on shape and dimensions","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 5: Barres rondes, carrées et hexagonales — Tolérances sur forme et dimensions",2012-06-22,3,['77.150.10'],ISO/TC 79/SC 6,9599,[28576],[76709],['en'],5,"<p>This part of ISO 6362 specifies the tolerances on dimensions and shape of the following:</p><p>— wrought aluminium and aluminium alloy extruded round bars, having diameters in the range from 8 mm</p><p>up to 350 mm;</p><p>— wrought aluminium and aluminium alloy extruded

52240,IS,,ISO 6362-6:2012,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 6: Round, square, rectangular and hexagonal tubes — Tolerances on shape and dimensions","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 6: Tubes ronds, carrés, rectangulaires et hexagonaux — Tolérances sur forme et dimensions",2012-06-22,1,['77.150.10'],ISO/TC 79/SC 6,9599,,"[76760,84607]",['en'],16,"<p>This part of ISO 6362 specifies the tolerances on dimensions and shape of wrought aluminium and aluminium</p><p>alloy extruded round bars having diameters in the range from 8 mm up to 350 mm; and square and hexagonal</p><p>bars having widths

52241,IS,,ISO 6362-7:2012,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 7: Chemical composition","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 7: Composition chimique",2012-06-22,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[65060],['en'],6,

65060,IS,,ISO 6362-7:2014,"Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 7: Chemical composition","Aluminium et alliages d'aluminium corroyés — Barres, tubes et profilés filés — Partie 7: Composition chimique",2014-09-17,2,['77.150.10'],ISO/TC 79/SC 6,9599,[52241],[76710],['en'],6,"<p>ISO 6362-7:2014 specifies the chemical composition of wrought aluminium and aluminium alloys. The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminium Association (known as the 'Teal Sheets'), for the corresponding alloys.</p>"

12690,IS,,ISO 6363-1:1988,Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes — Part 1: Technical conditions for inspection and delivery,Barres et tubes étirés à froid en aluminium et alliages d'aluminium corroyés — Partie 1: Conditions techniques de contrôle et de livraison,1988-12-01,1,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,[11197],[54486],"['en','fr']",4,"<p>This part of ISO 6363 applies to products for general engineering applications which are extruded and then cold-drawn. It does not apply to products which are rolled and then cold-drawn, including seam-welded tubes.</p>"

54486,IS,,ISO 6363-1:2012,"Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 1: Technical conditions for inspection and delivery","Aluminium et alliages d'aluminium corroyés — Barres, tubes et fils étirés à froid — Partie 1: Conditions techniques de contrôle et de livraison",2012-07-12,2,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,"[12690,12696]",[76711],['en'],14,"<p>This part of ISO 6363 specifies the technical conditions for the inspection and delivery of wrought aluminium and aluminium alloys rods/bars, tubes and wires for general engineering applications.</p><p>It applies to products which are extruded and then cold drawn.</p><p>It does not apply

12691,IS,,ISO 6363-2:1993,Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes — Part 2: Mechanical properties,Barres et tubes étirés à froid en aluminium et alliages d'aluminium corroyés — Partie 2: Caractéristiques mécaniques,1993-10-07,1,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,[7760],[54488],"['en','fr']",10,"<p>The following properties are specified: dimensions, tensile strength, 0,2 % proof stress, elongation. Does not apply to electrical conductors. The designations of aluminium and aluminium alloys and the temper designations are in accordance with ISO 2092, ISO 2107 and annex B respectively.</p>"

54488,IS,,ISO 6363-2:2012,Wrought aluminium and aluminium alloys — Cold-drawn rods/bars and tubes and wires — Part 2: Mechanical properties,"Aluminium et alliages d'aluminium corroyés — Barres, tubes et fils étirés à froid — Partie 2: Caractéristiques mécaniques",2012-07-12,2,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,[12691],[76712],['en'],18,"<p>This part of ISO 6363 specifies the mechanical properties of wrought aluminium and aluminium alloy rods/bars, tubes and wires for general engineering applications (except aeronautical rivets).</p><p>It applies to products which are extruded and then cold drawn.</p><p>It does not apply to:</p><p>— products which are rolled and then cold drawn,

54489,IS,,ISO 6363-3:2012,"Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 3: Drawn round bars and wires — Tolerances on form and dimensions (symmetric plus and minus tolerances on diameter)","Aluminium et alliages d'aluminium corroyés — Barres, tubes et fils étirés à froid — Partie 3: Barres rondes et fils étirés — Tolérances sur forme et dimensions (tolérances de diamètre symétriques en plus et en moins)",2012-07-12,1,['77.150.10'],ISO/TC 79/SC 6,9599,[11198],[76713],['en'],3,<p>ISO 6363-3:2012 specifies tolerances on form and dimensions for wrought aluminium and aluminium alloy drawn round bars and wires having diameters in the range of from 1 mm to 1

12692,IS,,ISO 6363-4:1991,Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes — Part 4: Drawn rectangular bars — Tolerances on form and dimensions,Barres et tubes étirés à froid en aluminium et alliages d'aluminium corroyés — Partie 4: Barres rectangulaires étirées — Tolérances sur forme et dimensions,1991-10-17,1,['77.150.10'],ISO/TC 79/SC 6,9599,,"[54490,28575]","['en','fr']",4,<p>Specifies tolerances for bars with thicknesses ranging from 2 mm up to 40 mm and widths up to 200 mm. The ratio of the largest section to the smallest one is up to 10 (see ISO 3134-3).</p>

54490,IS,,ISO 6363-4:2012,"Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 4: Drawn rectangular bars and wires — Tolerances on form and dimensions","Aluminium et alliages d'aluminium corroyés — Barres, tubes et fils étirés à froid — Partie 4: Barres rectangulaires et fils étirés — Tolérances sur forme et dimensions",2012-07-12,2,['77.150.10'],ISO/TC 79/SC 6,9599,[12692],[76714],['en'],7,"<p>This part of ISO 6363 specifies the tolerances on form and dimensions of wrought aluminium and aluminium alloy drawn rectangular bars and wires with thicknesses ranging from 2 mm up to and including 60 mm and widths up to and including 200 mm.</p><p>For wires, this pa

12693,IS,,ISO 6363-5:1992,Wrought aluminium and aluminium alloy cold-drawn rods/bars and tubes — Part 5: Drawn square and hexagonal bars — Tolerances on form and dimensions,Barres et tubes étirés à froid en aluminium et alliages d'aluminium corroyés — Partie 5: Barres carrées et hexagonales étirées — Tolérances sur forme et dimensions,1992-11-19,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[54491],"['en','fr']",2,"<p>Specifies the tolerances on form (straightness, twist) and dimensions (on width across flats, on fixed-length bars) of bars with width across flats up to and including 80 mm.</p>"

54491,IS,,ISO 6363-5:2012,"Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 5: Drawn square and hexagonal bars and wires — Tolerances on form and dimensions","Aluminium et alliages d'aluminium corroyés — Barres, tubes et fils étirés à froid — Partie 5: Barres carrées et hexagonales et fils étirés — Tolérances sur forme et dimensions",2012-07-12,2,['77.150.10'],ISO/TC 79/SC 6,9599,[12693],[76715],['en'],5,<p>ISO 6363-5:2012 specifies the tolerances on form and dimensions of wrought aluminium and aluminium alloy drawn square and hexagonal bars and wires with widths across flats up to and including 100 mm.</p>

54493,IS,,ISO 6363-6:2012,"Wrought aluminium and aluminium alloys — Cold-drawn rods/bars, tubes and wires — Part 6: Drawn round tubes — Tolerances on form and dimensions","Aluminium et alliages d'aluminium corroyés — Barres, tubes et fils étirés à froid — Partie 6: Tubes ronds étirés — Tolérances sur forme et dimensions",2012-07-12,1,"['23.040.15','77.150.10']",ISO/TC 79/SC 6,9599,,[76717],['en'],7,<p>This part of ISO 6363 specifies the tolerances on form and dimensions of wrought aluminium and aluminium alloy drawn round tubes (seamless and porthole).</p><p>This part of ISO 6363 applies to cold-drawn round tubes.</p>

12696,IS,,ISO 6365-1:1988,Wrought aluminium and aluminium alloy cold-drawn wire — Part 1: Technical conditions for inspection and delivery,Fils étirés à froid en aluminium et alliages d'aluminium corroyés — Partie 1: Conditions techniques de contrôle et de livraison,1988-12-08,1,['77.150.10'],ISO/TC 79/SC 6,9599,[11197],[54486],"['en','fr']",2,"<p>This part of ISO 6365 applies to products for general engineering applications. It does not apply to electrical wire. ISO 6365 will be consist of four parts. This part specifies for instance requirements to manufacturing process and quality control, the chemical composition, mechanical properties, surface finish, dimension and form tolerances, conf

12700,IS,,ISO 6370-2:1991,Vitreous and porcelain enamels — Determination of the resistance to abrasion — Part 2: Loss in mass after sub-surface abrasion,Émaux vitrifiés — Détermination de la résistance à l'abrasion — Partie 2: Perte de masse après abrasion de la couche superficielle,1991-11-28,1,['25.220.50'],ISO/TC 107,9599,,[59478],"['en','fr']",6,"<p>Specifies a test method for determining the resistance of enamel coats to abrasion by rubbing, grinding or other mechanical effects. Annexes A, B and C are for information only.</p>"

59478,IS,,ISO 6370-2:2011,Vitreous and porcelain enamels — Determination of the resistance to abrasion — Part 2: Loss in mass after sub-surface abrasion,Émaux vitrifiés — Détermination de la résistance à l'abrasion — Partie 2: Perte de masse après abrasion de la couche superficielle,2011-10-31,2,['25.220.50'],ISO/TC 107,9599,[12700],[75429],['en'],8,

12702,IS,,ISO 6372-1:1989,Nickel and nickel alloys — Terms and definitions — Part 1: Materials,Nickel et alliages de nickel — Termes et définitions — Partie 1: Matériaux,1989-06-22,1,"['01.040.77','77.120.40']",ISO/TC 155,9599,,[69352],"['en','fr']",2,<p>Terms and definitions listed in this part of ISO 6372 have been approved by the CCC (Customs Co-operation Council) to form the basis for the revision of chapter 75 'Nickel' of the CCC-Nomenclature. The three parts have been published bilingual (E/F). This part of ISO 6372 gives general terms for and definitions of materials. Contains a classification of nickel and nickel alloys.</p>

12703,IS,,ISO 6372-2:1989,Nickel and nickel alloys — Terms and definitions — Part 2: Refinery products,Nickel et alliages de nickel — Termes et définitions — Partie 2: Produits de raffinage,1989-06-22,1,"['01.040.77','77.120.40']",ISO/TC 155,9599,,[69352],"['en','fr']",2,"<p>Terms and definitions listed in this part of ISO 6372 have been approved by the CCC (Customs Co-operation Council) to form the basis for the revision of chapter 75 'Nickel' of the CCC-Nomenclature. The three parts have been published bilingual (E/F). This part of ISO 6372 gives terms for and definitions of refinery shapes and intermediate products of metallurgy, in the field of nickel and nickel alloys.</p>"

12704,IS,,ISO 6372-3:1989,Nickel and nickel alloys — Terms and definitions — Part 3: Wrought products and castings,Nickel et alliages de nickel — Termes et définitions — Partie 3: Produits corroyés et produits moulés,1989-05-25,1,"['77.150.40','01.040.77']",ISO/TC 155,9599,,[69352],"['en','fr']",7,<p>Terms and definitions listed in this part of ISO 6372 have been approved by the CCC (Customs Co-operation Council) to form the basis for the revision of chapter 75 'Nickel' of the CCC-Nomenclature. The three parts have been published bilingual (E/F). This part of ISO 6372 gives terms for and definitions of wrought products and castings of nickel and nickel alloys.</p>

77399,IS,,ISO 638-1:2021,"Paper, board, pulps and cellulosic nanomaterials — Determination of dry matter content by oven-drying method — Part 1: Materials in solid form","Papiers, cartons, pâtes et nanomatériaux cellulosiques — Détermination de la teneur en matières sèches par séchage à l'étuve — Partie 1: Matériaux sous forme solide",2021-05-06,1,"['85.060','85.040']",ISO/TC 6,9599,[42267],[83614],"['en','fr']",10,"<p>This document specifies an oven-drying method for the determination of the dry matter content in paper, board, pulp and cellulosic nanomaterials in solid form, which all can be produced from virgin and /or recycled materials.</p><p>It is also applicable to the determination of

4764,IS,,ISO 638:1978,Pulps — Determination of dry matter content,Pâtes — Détermination de la teneur en matières sèches,1978-10-01,1,['85.040'],ISO/TC 6,9599,,[42267],"['en','fr']",2,"<p>Applies to moist and air-dry pulp which does not contain any appreciable quantity of matter, other than water, volatile at the temperature specified for the drying, and is not applicable to the dry matter content of slush pulp or to the determination of the saleable mass of pulp lots.</p>"

77400,IS,,ISO 638-2:2021,"Paper, board, pulps and cellulosic nanomaterials — Determination of dry matter content by oven-drying method — Part 2: Suspensions of cellulosic nanomaterials","Papiers, cartons, pâtes et nanomatériaux cellulosiques — Détermination de la teneur en matières sèches par séchage à l'étuve — Partie 2: Suspensions de nanomatériaux cellulosiques",2021-05-06,1,"['85.060','85.040']",ISO/TC 6,9599,[42267],[83615],"['en','fr']",9,"<p>This document specifies an oven-drying method for the determination of the dry matter content in suspensions of cellulosic nanomaterials. The procedure is applicable to cellulosic nanomaterial suspensions which do not contain any appreciable quant

42267,IS,,ISO 638:2008,"Paper, board and pulps — Determination of dry matter content — Oven-drying method","Papiers, cartons et pâtes — Détermination de la teneur en matières sèches — Méthode par séchage à l'étuve",2008-09-16,2,"['85.060','85.040']",ISO/TC 6,9599,[4764],"[77400,77399]","['en','fr']",6,"<p>ISO 638:2008 specifies an oven-drying method for the determination of the dry matter in paper, board and pulp.</p><p>The procedure is applicable to paper, board and pulp which does not contain any appreciable quantities of materials other than water that are volatile at the temperature of 105 °C ± 2 °C. It is used, for example, in the case of pulp, paper and board samples taken for chemical

12715,IS,,ISO 6383-1:1983,Plastics — Film and sheeting — Determination of tear resistance — Part 1: Trouser tear method,Plastiques — Film et feuille — Détermination de la résistance au déchirement — Partie 1: Méthode de déchirement pantalon,1983-06-01,1,['83.140.10'],ISO/TC 61/SC 11,9599,,[67565],"['en','fr']",4,"<p>Specifies a method of determing the tear resistance of plastic film or sheet less than 1 mm thick, tested under defined conditions. A rectangular test specimen having a longitudinal slit extending over its half length is subjected to a tensile test on the 'trouser legs' formed by the slit. The average force required to tear the specimen completely along its length is used to calc

12718,IS,,ISO 6385:1981,Ergonomic principles in the design of work systems,Principes ergonomiques de la conception des systèmes de travail,1981-06-01,1,['13.180'],ISO/TC 159,9599,,"[12719,35885]","['en','fr']",4,"<p>Establishes these principles as basic guidelines. They apply for designing optimal working conditions with regard to human well-being, safety and health, taking into account technological and economic efficiency.</p>"

35885,IS,,ISO 6385:2004,Ergonomic principles in the design of work systems,Principes ergonomiques de la conception des systèmes de travail,2004-01-13,2,['13.180'],ISO/TC 159/SC 1,9599,[12718],[63785],"['en','fr']",11,"<p>ISO 6385:2004 establishes the fundamental principles of ergonomics as basic guidelines for the design of work systems and defines relevant basic terms. It describes an integrated approach to the design of work systems, where ergonomists will cooperate with others involved in the design, with attention to the human, the social and the technical requirements in a balanced manner during the design process.</p><p>While the principles in ISO 6385:2004 are oriented to the design o

12722,IS,,ISO 6388:1983,Surface active agents — Determination of flow properties using a rotational viscometer,Agents de surface — Détermination des propriétés d'écoulement au moyen d'un viscosimètre rotatif,1983-08-01,1,['71.100.40'],ISO/TC 91,9599,,[12723],"['en','fr']",7,

22109,IS,,ISO 639-1:2002,Codes for the representation of names of languages — Part 1: Alpha-2 code,Codes pour la représentation des noms de langue — Partie 1: Code alpha-2,2002-07-18,1,['01.140.20'],ISO/TC 37/SC 2,9599,[4766],[74575],"['en','fr']",37,"<p>This part of ISO 639 provides a code consisting of language code elements comprising two-letter language identifiers for the representation of names of languages. The language identifiers according to this part of ISO 639 were devised originally for use in terminology, lexicography and linguistics, but may be adopted for any application requiring the expression of language in two-letter coded form, especially in computerized systems. The alp

4766,IS,,ISO 639:1988,Code for the representation of names of languages,Code pour la représentation des noms de langue,1988-03-31,1,['01.140.20'],ISO/TC 37,9599,,[22109],"['en','fr']",17,"<p>Gives a two-letter lower-case code. The symbols were devised primarily for use in terminology, lexicography and linguistic, but they may be used for any application. It also includes guidance on the use of language symbols in some of these applications. The annex includes a classified list of languages and their symbols arranged by families.</p>"

4767,IS,,ISO 639-2:1998,Codes for the representation of names of languages — Part 2: Alpha-3 code,Codes pour la représentation des noms de langue — Partie 2: Code alpha-3,1998-10-22,1,['01.140.20'],ISO/TC 37/SC 2,9599,,[74575],"['en','fr']",66,

39534,IS,,ISO 639-3:2007,Codes for the representation of names of languages — Part 3: Alpha-3 code for comprehensive coverage of languages,Codes pour la représentation des noms de langues — Partie 3: Code alpha-3 pour un traitement exhaustif des langues,2007-02-05,1,['01.140.20'],ISO/TC 37/SC 2,9599,,[74575],"['en','fr']",12,"<p>ISO 639-3:2007 provides a code, published by the Registration Authority of ISO 639-3, consisting of language code elements comprising three-letter language identifiers for the representation of languages. The language identifiers according to this ISO 639-3:2007 were devised for use in a wide range of applications, especially in computer systems, where there is poten

39535,IS,,ISO 639-4:2010,"Codes for the representation of names of languages — Part 4: General principles of coding of the representation of names of languages and related entities, and application guidelines","Codes pour la représentation des noms de langue — Partie 4: Principes généraux pour le codage de la représentation des noms de langue et d'entités connexes, et lignes directrices pour la mise en oeuvre",2010-07-16,1,['01.140.20'],ISO/TC 37/SC 2,9599,,[74575],"['en','fr']",28,"<p>ISO 639-4:2010 gives the general principles of language coding using the codes that are specified in the other parts of ISO 639 and their combination with other codes. It also lays down guidelines for the use

39536,IS,,ISO 639-5:2008,Codes for the representation of names of languages — Part 5: Alpha-3 code for language families and groups,Codes pour la représentation des noms de langue — Partie 5: Code alpha-3 pour les familles de langues et groupes de langues,2008-05-15,1,['01.140.20'],ISO/TC 37/SC 2,9599,,[74575],"['en','fr']",23,"<p>ISO 639-5:2008 provides a code consisting of language code elements comprising three-letter language identifiers for the representation of names of living and extinct language families and groups. Languages designed exclusively for machine use, such as computer-programming languages, are not included in this code.</p>"

12724,IS,,ISO 6391:1988,Meat and meat products — Enumeration of Escherichia coli — Colony count technique at 44 degrees C using membranes,Viande et produits à base de viande — Dénombrement des Escherichia coli — Méthode par comptage des colonies obtenues sur membranes à 44 degrés C,1988-11-24,1,['07.100.30'],ISO/TC 34/SC 6,9599,,[24601],"['en','fr']",5,

12726,IS,,ISO 6392:1980,Earth-moving machinery — Lubrication fittings — Nipple type,Engins de terrassement — Raccords de graissage — Type à embout,1980-09-01,1,['53.100'],ISO/TC 127/SC 3,9599,,"[2125,12727]","['en','fr']",4,

12728,IS,,ISO 6393:1985,Acoustics — Measurement of airborne noise emitted by earth-moving machinery — Method for determining compliance with limits for exterior noise — Stationary test condition,Acoustique — Mesurage du bruit aérien émis par les engins de terrassement — Méthode de vérification de la conformité en ce qui concerne les limites de bruit extérieur — Condition d'essai statique,1985-05-09,1,"['17.140.20','53.100']",ISO/TC 43/SC 1,9599,,[1377],"['en','fr']",7,

1377,IS,,ISO 6393:1998,Acoustics — Measurement of exterior noise emitted by earth-moving machinery — Stationary test conditions,Acoustique — Mesurage du bruit émis à l'extérieur par les engins de terrassement — Conditions d'essai statiques,1998-11-19,2,"['17.140.20','53.100']",ISO/TC 43/SC 1,9599,[12728],[38481],['en'],11,

12729,IS,,ISO 6394:1985,Acoustics — Measurement of airborne noise emitted by earth-moving machinery — Operator's position — Stationary test condition,Acoustique — Mesurage du bruit aérien émis par les engins de terrassement — Poste de conduite — Condition d'essai statique,1985-05-16,1,"['17.140.20','53.100']",ISO/TC 43/SC 1,9599,,[21769],"['en','fr']",5,