Withdrawn and superseded ISO standards — page 140 of 246

12362,IS,,ISO 6133:1981,Rubber and plastics — Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength,Caoutchouc et plastiques — Analyse des tracés multi-pics obtenus lors des déterminations de la résistance au déchirement et de la force d'adhérence,1981-04-01,1,"['83.080.01','83.060']",ISO/TC 45/SC 2,9599,,[12363],"['en','fr']",3,

12363,IS,,ISO 6133:1998,Rubber and plastics — Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength,Caoutchouc et plastiques — Analyse des tracés multi-pics obtenus lors des déterminations de la résistance au déchirement et de la force d'adhérence,1998-02-26,2,"['83.080.01','83.060']",ISO/TC 45/SC 2,9599,[12362],[65921],"['en','fr']",5,

12364,IS,,ISO 6134:1981,Rubber hoses for steam — Specification,Tuyaux en caoutchouc pour la vapeur — Spécifications,1981-07-01,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[12365],"['en','fr']",3,

12365,IS,,ISO 6134:1992,Rubber hoses and hose assemblies for steam — Specification,Tuyaux et flexibles en caoutchouc pour la vapeur — Spécifications,1992-07-09,2,['23.040.70'],ISO/TC 45/SC 1,9599,[12364],[41169],"['en','fr']",4,"<p>Specifies the minimum requirements for two classes (non-oil-resistant cover and oil-resistant cover) and five types of rubber steam hoses and hose assemblies. Hoses complying with this standard are not suitable for use in the preparation of foodstuffs, e.g. by steam cooking, or for special service applications, e.g. as in pile drivers.</p>"

41169,IS,,ISO 6134:2005,Rubber hoses and hose assemblies for saturated steam — Specification,Tuyaux et flexibles en caoutchouc pour vapeur saturée — Spécification,2005-03-09,3,['23.040.70'],ISO/TC 45/SC 1,9599,[12365],[65367],"['en','fr']",13,"<p>ISO 6134:2005 specifies requirements for two types of hose and hose assembly, low pressure with a maximum working pressure of 6 bar and high pressure with a maximum working pressure of 18 bar, made of rubber with hose fittings made of metal, designed to convey saturated steam and hot water condensate.</p><p>Each type is divided into two classes having either an oil-resistant or a non-oil-resistant cover.</p><p>Information is also given on the freque

65367,IS,,ISO 6134:2017,Rubber hoses and hose assemblies for saturated steam — Specification,Tuyaux et flexibles en caoutchouc pour vapeur saturée — Spécification,2017-01-10,4,['23.040.70'],ISO/TC 45/SC 1,9599,[41169],[86387],"['en','fr']",12,"<p>ISO 6134:2017 specifies requirements for two types of hoses and hose assemblies, low pressure with a maximum working pressure of 6 bar and high pressure with a maximum working pressure of 18 bar, made of rubber and hose fittings made of metal, designed to convey saturated steam and hot water condensate.</p><p>Each type is divided into two classes having either an oil resistant or non-oil resistant cover.</p><p>NOTE Information on the freque

4732,IS,,ISO 614:1976,Shipbuilding — Toughened safety glass panes for ships' side scuttles and ships' rectangular windows — Punch method of non-destructive strength testing,Construction navale — Verres de sécurité trempés pour hublots et fenêtres rectangulaires de navires — Méthode du poinçon pour les essais non destructifs de résistance,1976-09-01,2,"['47.020.10','81.040.30']",ISO/TC 8/SC 8,9599,,[4733],"['en','fr']",3,

4733,IS,,ISO 614:1989,Shipbuilding and marine structures — Toughened safety glass panes for rectangular windows and side scuttles — Punch method of non-destructive strength testing,Construction navale et structures maritimes — Verres de sécurité trempés pour hublots et fenêtres rectangulaires de navires — Méthode du poinçon pour les essais non destructifs de résistance,1989-09-21,3,"['47.020.10','81.040.30']",ISO/TC 8/SC 8,9599,[4732],[54514],"['en','fr']",3,<p>Specifies the appropiate method for testing complying with ISO 3254 and ISO 1095.</p>

12370,IS,,ISO 6141:1979,Gas analysis — Calibration gas mixtures — Certificate of mixture preparation,Analyse des gaz — Mélanges de gaz pour étalonnage — Certificat de préparation du mélange,1979-04-01,1,['71.040.40'],ISO/TC 158,9599,,[12371],"['en','fr']",2,

12371,IS,,ISO 6141:1984,Gas analysis — Calibration gas mixtures — Certificate of mixture preparation,Analyse des gaz — Mélanges de gaz pour étalonnage — Certificat de préparation du mélange,1984-12-01,2,['71.040.40'],ISO/TC 158,9599,[12370],[24664],"['en','fr']",2,

24664,IS,,ISO 6141:2000,Gas analysis — Requirements for certificates for calibration gases and gas mixtures,Analyse des gaz — Prescriptions relatives aux certificats de gaz et mélanges de gaz pour étalonnage,2000-05-18,3,['71.040.40'],ISO/TC 158,9599,[12371],[53597],"['en','fr']",8,

12372,IS,,ISO 6142:1981,Gas analysis — Preparation of calibration gas mixtures — Weighing methods,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthodes pondérales,1981-07-01,1,['71.040.40'],ISO/TC 158,9599,,[24663],"['en','fr']",7,

12373,IS,Add,ISO 6142:1981/Add 1:1983,Gas analysis — Preparation of calibration gas mixtures — Weighing methods — Addendum 1,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthodes pondérales — Additif 1,1983-05-01,1,['71.040.40'],ISO/TC 158,9599,,[24663],"['en','fr']",3,

24663,IS,,ISO 6142:2001,Gas analysis — Preparation of calibration gas mixtures — Gravimetric method,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthode gravimétrique,2001-04-12,2,['71.040.40'],ISO/TC 158,9599,"[12372,12373]",[59631],"['en','fr']",37,

44764,IS,Amd,ISO 6142:2001/Amd 1:2009,Gas analysis — Preparation of calibration gas mixtures — Gravimetric method — Amendment 1: Liquid introduction,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthode gravimétrique — Amendement 1: Introduction de liquides,2009-05-20,2,['71.040.40'],ISO/TC 158,9599,,[59631],"['en','fr']",8,

12374,IS,,ISO 6143:1981,Gas analysis — Determination of composition of calibration gas mixtures — Comparison methods,Analyse des gaz — Détermination de la composition de mélanges de gaz pour étalonnage — Méthodes par comparaison,1981-06-01,1,['71.040.40'],ISO/TC 158,9599,,[24665],"['en','fr']",4,

24665,IS,,ISO 6143:2001,Gas analysis — Comparison methods for determining and checking the composition of calibration gas mixtures,Analyse des gaz — Méthodes comparatives pour la détermination et la vérification de la composition des mélanges de gaz pour étalonnage,2001-05-31,2,['71.040.40'],ISO/TC 158,9599,[12374],[85579],"['en','fr']",33,"<p>This International Standard provides methods for</p><p>_ determining the composition of a calibration gas mixture by comparison with appropriate reference gas</p><p>mixtures,</p><p>_ calculating the uncertainty of the composition of a calibration gas mixture in relation to the known uncertainty of</p><p>the composition of the reference gas mixtures wit

12375,IS,,ISO 6144:1981,Gas analysis — Preparation of calibration gas mixtures — Static volumetric methods,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthodes volumétriques statiques,1981-07-01,1,['71.040.40'],ISO/TC 158,9599,,[24666],"['en','fr']",13,<p>Describes principles for non continuous preparation of mixtures at or near atmosphere pressure and procedure for calculation of errors. Applies to mixtures in the range from 10-6 to 10 -1 (V/V) for which the relative uncertainty is between 10-3 and 10-2.</p>

12376,IS,,ISO 6145-1:1986,Gas analysis — Preparation of calibration gas mixtures — Dynamic volumetric methods — Part 1: Methods of calibration,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthodes volumétriques dynamiques — Partie 1: Méthodes d'étalonnage,1986-10-09,1,['71.040.40'],ISO/TC 158,9599,,[24667],"['en','fr']",21,<p>Describes various methods and given a brief and non-exhaustivepresentation of examples of techniques and error calculations which are described in more detail in other parts of ISO 6145. Tabulates examples of influence of temperature and pressure variations. Seven figures illustrate different equipment.</p>

24667,IS,,ISO 6145-1:2003,Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 1: Methods of calibration,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage à l'aide de méthodes volumétriques dynamiques — Partie 1: Méthodes d'étalonnage,2003-11-12,2,['71.040.40'],ISO/TC 158,9599,[12376],[53598],"['en','fr']",32,<p>ISO 6145-1:2003 specifies the calibration methods involved in the preparation of gas mixtures by dynamic volumetric techniques. It also gives a brief presentation of a non-exhaustive list of examples of dynamic volumetric techniques which are described in more detail in other parts of ISO 6145.</p>

33361,IS,,ISO 6145-2:2001,Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 2: Volumetric pumps,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage à l'aide de méthodes volumétriques dynamiques — Partie 2: Pompes volumétriques,2001-07-05,1,['71.040.40'],ISO/TC 158,9599,,[45866],"['en','fr']",8,

12379,IS,,ISO 6145-4:1986,Gas analysis — Preparation of calibration gas mixtures — Dynamic volumetric methods — Part 4: Continuous injection method,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthodes volumétriques dynamiques — Partie 4: Méthode d'injection continue,1986-10-09,1,['71.040.40'],ISO/TC 158,9599,,[36478],"['en','fr']",5,"<p>Describes the preparation of mixtures by continuos mixing of volume flows, whereby the precision of the concentration of each constituent in the range from 10 000 to 10 ppm (V/V) amounts to about 5%. Includes a practical example with figure.</p>"

33362,IS,,ISO 6145-5:2001,Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 5: Capillary calibration devices,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage à l'aide de méthodes volumétriques dynamiques — Partie 5: Dispositifs d'étalonnage par capillaires,2001-04-19,1,['71.040.40'],ISO/TC 158,9599,,[45470],"['en','fr']",10,

12381,IS,,ISO 6145-6:1986,Gas analysis — Preparation of calibration gas mixtures — Dynamic volumetric methods — Part 6: Sonic orifices,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthodes volumétriques dynamiques — Partie 6: Orifices avec écoulement sonique,1986-10-09,1,['71.040.40'],ISO/TC 158,9599,,[28433],"['en','fr']",6,"<p>Describes the method using mixtures with one or more component(s), with a volume radio equal to or greater than 0,1 %, the repeatability of which on the concentration of each of the components is approximalety 0,5 % in relative value.</p>"

28433,IS,,ISO 6145-6:2003,Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 6: Critical orifices,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage à l'aide de méthodes volumétriques dynamiques — Partie 6: Orifices critiques,2003-05-08,2,['71.040.40'],ISO/TC 158,9599,[12381],[60247],"['en','fr']",11,"<p>ISO 6145-6:2003 specifies a method for the continuous production of calibration gas mixtures, containing two or more components, from pure gases or other gas mixtures by use of critical orifice systems. By selection of appropriate combinations of orifices and with the use of pure gases, the volume fraction of the calibration componen

33363,IS,,ISO 6145-7:2001,Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 7: Thermal mass-flow controllers,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage à l'aide de méthodes volumétriques dynamiques — Partie 7: Régulateurs thermiques de débit-masse,2001-04-19,1,['71.040.40'],ISO/TC 158,9599,,[45471],"['en','fr']",12,

45471,IS,,ISO 6145-7:2009,Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 7: Thermal mass-flow controllers,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage à l'aide de méthodes volumétriques dynamiques — Partie 7: Régulateurs thermiques de débit massique,2009-03-18,2,['71.040.40'],ISO/TC 158,9599,[33363],[73212],"['en','fr']",15,"<p>ISO 6145-7:2009 specifies a method for continuous production of calibration gas mixtures, containing two or more components, from pure gases or other gas mixtures by use of commercially available thermal mass-flow controllers. </p><p>If this method is employed for the preparation of calibration gas m

24668,IS,,ISO 6145-9:2001,Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 9: Saturation method,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage à l'aide de méthodes volumétriques dynamiques — Partie 9: Méthode par saturation,2001-04-19,1,['71.040.40'],ISO/TC 158,9599,[12385],[45469],"['en','fr']",13,

36681,IS,Cor,ISO 6145-9:2001/Cor 1:2002,Gas analysis — Preparation of calibration gas mixtures using dynamic volumetric methods — Part 9: Saturation method — Technical Corrigendum 1,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage à l'aide de méthodes volumétriques dynamiques — Partie 9: Méthode par saturation — Rectificatif technique 1,2002-05-16,1,['71.040.40'],ISO/TC 158,9599,,[45469],"['en','fr']",1,

12385,IS,,ISO 6147:1979,Gas analysis — Preparation of calibration gas mixtures — Saturation method,Analyse des gaz — Préparation des mélanges de gaz pour étalonnage — Méthode par saturation,1979-02-01,1,['71.040.40'],ISO/TC 158,9599,,[24668],"['en','fr']",2,"<p>Describes the principles of the method for continuous preparation, whereat one of the components is readily condensable. Gives practical example with schematic diagram and calculation of the error.</p>"

12386,IS,,ISO 6148:1993,Photography — Film dimensions — Micrographics,Photographie — Dimensions des films — Micrographie,1993-09-16,1,"['37.040.20','37.080']",ISO/TC 42,9599,,[33392],"['en','fr']",10,

12388,IS,,ISO 6149-1:1993,Connections for fluid power and general use — Ports and stud ends with ISO 261 threads and O-ring sealing — Part 1: Ports with O-ring seal in truncated housing,Raccordements pour transmissions hydrauliques et pneumatiques et applications générales — Orifices et éléments mâles à filetage ISO 261 et joint torique — Partie 1: Orifices à joint torique dans un logement tronconique,1993-10-28,1,['23.100.40'],ISO/TC 131/SC 4,9599,[12387],"[29846,39281]","['en','fr']",6,"<p>Specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends detailed in ISO 6149-2 and ISO 6149-3. Ports in accordance with this part may be used at working pressures u

39281,IS,,ISO 6149-1:2006,Connections for hydraulic fluid power and general use — Ports and stud ends with ISO 261 metric threads and O-ring sealing — Part 1: Ports with truncated housing for O-ring seal,Raccordements pour transmissions hydrauliques et applications générales — Orifices et éléments mâles à filetage métrique ISO 261 et joint torique — Partie 1: Orifices à joint torique dans un logement tronconique,2006-02-23,2,['23.100.40'],ISO/TC 131/SC 4,9599,[12388],[70260],"['en','fr']",6,"<p>ISO 6149-1:2006 specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends detailed in ISO 6149-2:2006 and ISO 6149-3:2006.</p><p>Ports in accordance with ISO 6149-

70260,IS,,ISO 6149-1:2019,Connections for hydraulic fluid power and general use — Ports and stud ends with ISO 261 metric threads and O-ring sealing — Part 1: Ports with truncated housing for O-ring seal,Raccordements pour transmissions hydrauliques et applications générales — Orifices et éléments mâles à filetage métrique ISO 261 et joint torique — Partie 1: Orifices à joint torique dans un logement tronconique,2019-04-16,3,['23.100.40'],ISO/TC 131/SC 4,9599,[39281],[83385],"['en','fr']",6,"<p>This document specifies dimensions for metric ports for use with the adjustable and non-adjustable stud ends as described in ISO 6149‑2 and ISO 6149‑3.</p><p>Ports in accordance with this document can

12387,IS,,ISO 6149:1980,Fluid power systems and components — Metric ports — Dimensions and design,"Transmissions hydrauliques et pneumatiques— Orifices de raccordement, série métrique — Dimensions et types",1980-10-01,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[12388],"['en','fr']",2,

12389,IS,,ISO 6149-2:1993,"Connections for fluid power and general use — Ports and stud ends with ISO 261 threads and O-ring sealing — Part 2: Heavy-duty (S series) stud ends — Dimensions, design, test methods and requirements","Raccordements pour transmissions hydrauliques et pneumatiques et applications générales — Orifices et éléments mâles à filetage ISO 261 et joint torique — Partie 2: Éléments mâles de série lourde (série S) — Dimensions, conception, méthodes d'essai et prescriptions",1993-10-28,1,['23.100.40'],ISO/TC 131/SC 4,9599,,"[29847,39280]","['en','fr']",10,"<p>Stud ends in accordance with this part may be used at working pressures up to 63 MPa (630 bar) for non-adjustable stud

12390,IS,,ISO 6149-3:1993,"Connections for fluid power and general use — Ports and stud ends with ISO 261 threads and O-ring sealing — Part 3: Light-duty (L series) stud ends — Dimensions, design, test methods and requirements","Raccordements pour transmissions hydrauliques et pneumatiques et applications générales — Orifices et éléments mâles à filetage ISO 261 et joint torique — Partie 3: Éléments mâles de série légère (série L) — Dimensions, conception, méthodes d'essai et prescriptions",1993-10-28,1,['23.100.40'],ISO/TC 131/SC 4,9599,,"[29848,39279]","['en','fr']",10,"<p>Stud ends in accordance with this part may be used at working pressures up to 40 MPa (400 bar) for non-adjustable stud

41139,IS,,ISO 6149-4:2006,"Connections for fluid power and general use — Ports and stud ends with ISO 261 metric threads and O-ring sealing — Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs","Raccordements pour transmissions hydrauliques et applications générales — Orifices et éléments mâles à filetage métrique ISO 261 et joint torique — Partie 4: Dimensions, conception, méthodes d'essai et exigences des bouchons d'orifice à six pans externes et à six pans internes",2006-05-16,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[71182],"['en','fr']",10,"<p>ISO 6149-4:2006 specifies dimensions and performance requirements for external hex and internal

12391,IS,,ISO 6150:1988,"Pneumatic fluid power — Cylindrical quick-action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 MPa, 1,6 Mpa, and 2,5 MPa) — Plug connecting dimensions, specifications, application guidelines and testing","Transmissions pneumatiques — Raccords rapides cylindriques pour pressions maximales d'utilisation 10 bar, 16 bar et 25 bar (1 MPa, 1,6 MPa et 2,5 MPa) — Dimensions de raccordement de la partie mâle, spécifications, conseils d'utilisation et essais",1988-04-14,1,['23.100.40'],ISO/TC 131/SC 4,9599,,"[25457,73511]","['en','fr']",13,"<p>Lays down the dimensions and tolerances so as to ensure the interchangeability of pneumatic coupling plugs. G

12398,IS,,ISO 6155-1:1981,"Acceptance conditions for horizontal spindle capstan, turret and single spindle automatic lathes — Testing of the accuracy — Part 1: Machinable bar diameters greater than 25 mm","Conditions de réception des tours semi-automatiques à tourelle révolver et à broche horizontale, et des tours automatiques monobroches — Contrôle de la précision — Partie 1: Diamètres de barre usinables supérieurs à 25 mm",1981-06-01,1,['25.080.10'],ISO/TC 39/SC 2,9599,,[25593],"['en','fr']",22,

25593,IS,,ISO 6155:1998,Machine tools — Test conditions for horizontal spindle turret and single spindle automatic lathes — Testing of the accuracy,Machines-outils — Conditions d'essai des tours à tourelle revolver à broche horizontale et des tours automatiques monobroche — Contrôle de la précision,1998-03-19,1,['25.080.10'],ISO/TC 39/SC 2,9599,"[12399,12398]",[69009],"['en','fr']",30,

12399,IS,,ISO 6155-2:1986,"Acceptance conditions for horizontal spindle capstan, turret and single spindle automatic lathes — Testing of the accuracy — Part 2: Machinable bar diameters 25 mm or less and chuck diameter up to 160 mm","Conditions de réception des tours semi- automatiques à tourelle revolver et à broche horizontale, et des tours automatiques monobroches — Contrôle de la précision — Partie 2: Tours à diamètres de passage en barre inférieurs ou égaux à 25 mm et en mandrins inférieurs ou égaux à 160 mm",1986-11-27,1,['25.080.10'],ISO/TC 39/SC 2,9599,,[25593],"['en','fr']",23,

12404,IS,,ISO 6158:1984,Metallic coatings — Electroplated coatings of chromium for engineering purposes,Revêtements métalliques — Dépôts électrolytiques de chrome pour usages industriels,1984-06-01,1,['25.220.40'],ISO/TC 107/SC 3,9599,,[37511],"['en','fr']",7,"<p>Specifies requirements for these coatings, with or without undercoats, on ferrous and non-ferrous metals. Defines the term 'significant surface' and gives sampling, information to be supplied to the electroplater, treatment of basis meatal, coating requirements. heat treatment, test methods and peening conditions (annex A) and reclamation of worn chromium electroplated articles (annex B) respectively.</p>"

37511,IS,,ISO 6158:2004,Metallic coatings — Electrodeposited coatings of chromium for engineering purposes,Revêtements métalliques — Dépôts électrolytiques de chrome pour usages industriels,2004-06-01,2,['25.220.40'],ISO/TC 107/SC 3,9599,[12404],[56850],"['en','fr']",12,"<p>ISO 6158:2004 specifies requirements for electroplated coatings of chromium, with or without undercoats, on ferrous and non-ferrous metals for engineering purposes.</p><p>The coating designation provides a means of specifying the thickness of chromium appropriate for typical engineering applications.</p>"

56850,IS,,ISO 6158:2011,Metallic and other inorganic coatings — Electrodeposited coatings of chromium for engineering purposes,Revêtements métalliques et autres revêtements inorganiques — Dépôts électrolytiques de chrome pour usages industriels,2011-07-14,3,['25.220.40'],ISO/TC 107/SC 3,9599,[37511],[72269],"['en','fr','ru']",12,"<p>ISO 6158:2011 specifies requirements for electroplated coatings of hexavalent chromium, with or without undercoats, on ferrous and non-ferrous metals for engineering purposes. The coating designation provides a means of specifying the thickness of chromium appropriate for typical engineering applications.</p>"

12405,IS,,ISO 6159:1980,Data communication — HDLC unbalanced classes of procedures,Téléinformatique — Classes de procédure HDLC non équilibrée,1980-05-01,1,['35.100.20'],ISO/IEC JTC 1/SC 6,9599,,[14707],"['en','fr']",6,

4735,IS,,ISO 616:1977,Coke — Determination of shatter indices,Coke — Détermination des indices de chute,1977-12-01,1,['75.160.10'],ISO/TC 27/SC 3,9599,,[1950],"['en','fr']",6,

1950,IS,,ISO 616:1995,Coke — Determination of shatter indices,Coke — Détermination des indices de chute,1995-10-19,2,['75.160.10'],ISO/TC 27/SC 3,9599,[4735],[78698],['en'],5,"<p>Specifies a method for determining the strength of coke by the shatter test. Replaces the first edition, which has been technically revised.</p>"

12407,IS,,ISO 6161:1981,Personal eye-protectors — Filters and eye-protectors against laser radiation,Protecteurs individuels de l'oeil — Filtres et protecteurs de l'oeil contre les rayons laser,1981-02-01,1,['13.340.20'],ISO/TC 94/SC 6,9599,,[74268],"['en','fr']",4,"<p>Specifies requirements for spectacle filters and protectors within the spectral region 0,2 to 1000 micron. The work, which was staggered over several years, represents a basic study for which a majority consensus was reached at the international level. To take account of new developments and knowledge relating to lasers a revision of this standard will be undertaken.</p>"

36634,IS,,ISO 6162-1:2002,"Hydraulic fluid power — Flange connectors with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127","Transmissions hydrauliques — Raccordements à bride avec demi-brides ou bride monobloc et vis métriques ou en inches — Partie 1: Raccordements à bride pour utilisation à des pressions de 3,5 MPa (35 bar) à 35 MPa (350 bar), DN 13 à DN 127",2002-12-02,1,['23.100.40'],ISO/TC 131/SC 4,9599,[12408],[52096],"['en','fr']",18,"<p>ISO 6162-1:2002 specifies complete general and dimensional characteristics for flange heads, split flange clamps (FCS), one-piece flang

41247,IS,Cor,ISO 6162-1:2002/Cor 1:2004,"Hydraulic fluid power — Flange connectors with split or one-piece flange clamps and metric or inch screws — Part 1: Flange connectors for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127 — Technical Corrigendum 1","Transmissions hydrauliques — Raccordements à bride avec demi-brides ou bride monobloc et vis métriques ou en inches — Partie 1: Raccordements à bride pour utilisation à des pressions de 3,5 MPa (35 bar) à 35 MPa (350 bar), DN 13 à DN 127 — Rectificatif technique 1",2004-11-03,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[52096],"['en','fr']",1,

12408,IS,,ISO 6162:1994,"Hydraulic fluid power — Four-screw split-flange connections for use at pressures of 2,5 MPa to 40 MPa (25 bar to 400 bar) — Type I metric series and type II inch series","Transmissions hydrauliques — Brides de raccordement fendues à quatre vis pour des pressions d'utilisation de 2,5 MPa à 40 MPa (25 bar à 400 bar) — Type I série métrique et type II série en inches",1994-04-14,1,['23.100.40'],ISO/TC 131/SC 4,9599,,"[24849,36635,24848,36634]","['en','fr']",13,"<p>Gives complete general and dimensional specifications. For flange connections, a minimum design factor of 2,5 is valid with screws of property class 8.8, not including weld joints, for which special instructio

36635,IS,,ISO 6162-2:2002,"Hydraulic fluid power — Flange connectors with split or one-piece flange clamps and metric or inch screws — Part 2: Flange connectors for use at pressures of 35 MPa (350 bar) to 40 MPa (400 bar), DN 13 to DN 51","Transmissions hydrauliques — Raccordements à bride avec demi-brides ou bride monobloc et vis métriques ou en inches — Partie 2: Raccordements à bride pour utilisation à des pressions de 35 MPa (350 bar) à 40 MPa (400 bar), DN 13 à DN 51",2002-11-21,1,['23.100.40'],ISO/TC 131/SC 4,9599,[12408],[52097],"['en','fr']",18,"<p>ISO 6162-2:2002 specifies complete general and dimensional characteristics for flange heads, split flange clamps (FCS), one-piece flange

52097,IS,,ISO 6162-2:2012,"Hydraulic fluid power — Flange connections with split or one-piece flange clamps and metric or inch screws — Part 2: Flange connectors, ports and mounting surfaces for use at a pressure of 42 MPa (420 bar), DN 13 to DN 76","Transmissions hydrauliques — Raccordements à bride avec demi-brides ou bride monobloc et vis métriques ou en inches — Partie 2: Brides, orifices et surfaces de montage pour utilisation à une pression de 42 MPa (420 bar), de DN 13 à DN 76",2012-12-14,2,['23.100.40'],ISO/TC 131/SC 4,9599,[36635],[68567],"['en','fr']",21,"<p>ISO 6162-2:2012 gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece

12412,IS,,ISO 6164:1994,"Hydraulic fluid power — Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar)",Transmissions hydrauliques — Brides de raccordement carrées monobloc à quatre vis pour des pressions d'utilisation de 25 MPa et 40 MPa (250 bar et 400 bar),1994-04-14,1,['23.100.40'],ISO/TC 131/SC 4,9599,,"[59930,36796,36797,36798]","['en','fr']",11,"<p>Gives complete general and dimensional specifications. For flange connections, a design factor of 2,5 is valid, not including weld joints, for which special instructions exist. Also specifies the dimensions of the seals to be used, as well as the grooves to house the seals.</p>" 1241

12413,IS,,ISO 6165:1978,Earth-moving machinery — Basic types — Vocabulary,Engins de terrassement — Principaux types — Vocabulaire,1978-09-01,1,"['53.100','01.040.53']",ISO/TC 127/SC 4,9599,,[12414],"['en','fr']",1,

12414,IS,,ISO 6165:1987,Earth-moving machinery — Basic types — Vocabulary,Engins de terrassement — Principaux types — Vocabulaire,1987-12-03,2,"['01.040.53','53.100']",ISO/TC 127/SC 4,9599,[12413],[22030],"['en','fr']",2,

22030,IS,,ISO 6165:1997,Earth-moving machinery — Basic types — Vocabulary,Engins de terrassement — Principaux types — Vocabulaire,1997-04-10,3,"['01.040.53','53.100']",ISO/TC 127/SC 4,9599,[12414],[32958],"['en','fr']",6,

32958,IS,,ISO 6165:2001,Earth-moving machinery — Basic types — Vocabulary,Engins de terrassement — Principaux types — Vocabulaire,2001-07-26,4,"['53.100','01.040.53']",ISO/TC 127/SC 4,9599,[22030],[38495],"['en','fr']",7,

38495,IS,,ISO 6165:2006,Earth-moving machinery — Basic types — Identification and terms and definitions,Engins de terrassement — Principaux types — Identification et termes et définitions,2006-05-10,5,"['01.040.53','53.100']",ISO/TC 127/SC 4,9599,"[32958,36133]",[52639],"['en','fr']",14,"<p>ISO 6165:2006 gives terms and definitions and an identification structure for classifying earth-moving machinery designed to perform the following operations: excavation, loading, transportation, and drilling, spreading, compacting or trenching of earth and other materials (e.g. during work on roads and dams, and on building sites). Its purpose is to provide a clear means of identifying machines according

52639,IS,,ISO 6165:2012,Earth-moving machinery — Basic types — Identification and terms and definitions,Engins de terrassement — Principaux types — Identification et termes et définitions,2012-09-04,6,"['53.100','01.040.53']",ISO/TC 127/SC 4,9599,[38495],[77616],"['en','fr']",11,"<p>ISO 6165:2012 gives terms and definitions and an identification structure for classifying earth-moving machinery designed to perform the following operations: excavation, loading, transportation, and drilling, spreading, compacting or trenching of earth, rock and other materials, during work, for example, on roads and dams, in quarries and mines, and on building sites. Its purpose is to provide a clear means of i

12415,IS,,ISO 6166:1986,Securities — International securities identification numbering system (ISIN),Valeurs mobilières — Système international de numérotation pour l'identification des valeurs mobilières (ISIN),1986-02-13,3,['03.060'],ISO/TC 68,9599,,[12416],"['en','fr']",,

12416,IS,,ISO 6166:1987,Securities — International securities identification numbering system (ISIN),Valeurs mobilières — Système international de numérotation pour l'identification des valeurs mobilières (ISIN),1987-11-26,4,['03.060'],ISO/TC 68,9599,[12415],[12417],['en'],10,

12417,IS,,ISO 6166:1994,Securities — International securities identification numbering system (ISIN),Valeurs mobilières — Système international de numérotation pour l'identification des valeurs mobilières (ISIN),1994-03-10,5,['03.060'],ISO/TC 68,9599,[12416],[33446],"['en','fr']",8,

29641,IS,Cor,ISO 6166:1994/Cor 1:1997,Securities — International securities identification numbering system (ISIN) — Technical Corrigendum 1,Valeurs mobilières — Système international de numérotation pour l'identification des valeurs mobilières (ISIN) — Rectificatif technique 1: (Concerne uniquement la version anglaise),1997-12-04,5,['03.060'],ISO/TC 68,9599,,[33446],['en'],1,

33446,IS,,ISO 6166:2001,Securities and related financial instruments — International securities identification numbering system (ISIN),Valeurs mobilières et autres instruments financiers concernés — Système international de numérotation pour l'identification des valeurs mobilières (ISIN),2001-03-22,6,['03.060'],ISO/TC 68,9599,"[12417,29641]",[44811],"['en','fr','ru']",9,

44811,IS,,ISO 6166:2013,Securities and related financial instruments — International securities identification numbering system (ISIN),Valeurs mobilières et autres instruments financiers concernés — Système international de numérotation pour l'identification des valeurs mobilières (ISIN),2013-07-23,7,['03.060'],ISO/TC 68/SC 8,9599,[33446],[78502],['en'],11,<p>ISO 6166:2013 provides a uniform structure for the identification of fungible and non-fungible securities and financial instruments using a unique identification number and associated minimum descriptive data.</p>

12419,IS,,ISO 6168:1980,Abrasive products — Diamond or cubic boron nitride grinding wheels — Dimensions,Produits abrasifs — Meules à base de diamant ou de nitrure de bore cubique — Dimensions,1980-09-01,1,['25.100.70'],ISO/TC 29/SC 5,9599,,[28478],"['en','fr']",15,<p>The diamond or cubic nitride concentration and the grain size of the diamond section of the grinding wheels shall be specified in accordance with ISO 6104 and ISO 6106 respectively. Gives various types of grinding wheels in diagrammatic illustrations and their dimensions in tables.</p>

12421,IS,,ISO 6170:1983,Spinning machinery — Condenser rubbers for cards,Machines de filature — Manchons-frotteurs (de sortie) de cardes,1983-05-01,1,['59.120.10'],ISO/TC 72/SC 1,9599,,[27409],"['en','fr']",3,

12425,IS,,ISO 6175:1983,Textile machinery and accessories — Recommended profile threads for weaver's beams,Matériel pour l'industrie textile — Profils recommandés pour les filetages des ensouples de tissage,1983-04-01,1,['59.120.20'],ISO/TC 72/SC 3,9599,,[1366],"['en','fr']",2,

12426,IS,,ISO 6176:1981,Textile machinery — Warp sizing machines — Maximum usable width,Matériel pour l'industrie textile — Encolleuses — Largeurs maximales utilisables,1981-12-01,1,['59.120.30'],ISO/TC 72,9599,,[21947],"['en','fr']",1,

12427,IS,,ISO 6177:1983,Textile machinery — Cloth rollers — Terminology and main dimensions,Matériel pour l'industrie textile — Rouleaux magasins — Terminologie et dimensions principales,1983-05-01,1,['59.120.30'],ISO/TC 72/SC 3,9599,,[12428],"['en','fr']",4,

12430,IS,,ISO 6179:1981,Fabrics coated with vulcanized rubber — Determination of vapour transmission rate of volatile liquids (Gravimetric technique),Supports textiles revêtus de caoutchouc vulcanisé — Détermination du taux de transmission des liquides volatils (Méthode gravimétrique),1981-03-01,1,['59.080.40'],ISO/TC 45,9599,,[12431],"['en','fr']",4,

12431,IS,,ISO 6179:1989,"Vulcanized rubber sheet, and fabrics coated with vulcanized rubber — Determination of transmission rate of volatile liquids (Gravimetric technique)",Feuilles de caoutchouc vulcanisé et supports textiles revêtus de caoutchouc vulcanisé — Détermination du taux de transmission des liquides volatils (Technique gravimétrique),1989-12-21,2,"['83.140.10','59.080.40']",ISO/TC 45/SC 2,9599,[12430],[25525],"['en','fr']",4,

25525,IS,,ISO 6179:1998,"Rubber, vulcanized or thermoplastic — Rubber sheets and rubber-coated fabrics — Determination of transmission rate of volatile liquids (gravimetric technique)",Caoutchouc vulcanisé ou thermoplastique — Feuilles de caoutchouc et supports textiles revêtus de caoutchouc — Détermination du taux de transmission des liquides volatils (technique gravimétrique),1998-04-09,3,"['83.140.10','59.080.40']",ISO/TC 45/SC 2,9599,[12431],[52168],"['en','fr']",6,

52168,IS,,ISO 6179:2010,"Rubber, vulcanized or thermoplastic — Rubber sheets and rubber-coated fabrics — Determination of transmission rate of volatile liquids (gravimetric technique)",Caoutchouc vulcanisé ou thermoplastique — Feuilles de caoutchouc et supports textiles revêtus de caoutchouc — Détermination du taux de transmission des liquides volatils (technique gravimétrique),2010-03-01,4,"['83.140.10','59.080.40']",ISO/TC 45/SC 2,9599,[25525],[70356],"['en','fr','ru']",6,"<p>ISO 6179:2010 specifies two methods for determining, by measurement of the transmission rate, the permeability of rubber to volatile liquids diffusing into open air.</p><p>It is applicable only to materials in sheet f

12432,IS,,ISO 6182-1:1993,Fire protection — Automatic sprinkler systems — Part 1: Requirements and test methods for sprinklers,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 1: Prescriptions et méthodes d'essai des sprinklers,1993-06-17,1,['13.220.20'],ISO/TC 21/SC 5,9599,,"[38680,29265]","['en','fr']",30,"<p>Specifies performance requirements, test methods and marking requirements for fusible element and glass bulb sprinklers. For special sprinklers, special tests are necessary, which are in preparation.</p>"

38680,IS,,ISO 6182-1:2004,Fire protection — Automatic sprinkler systems — Part 1: Requirements and test methods for sprinklers,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 1: Prescriptions et méthodes d'essai des sprinklers,2004-01-20,2,['13.220.20'],ISO/TC 21/SC 5,9599,[12432],[56548],['en'],66,"<p>ISO 6182-1:2004 specifies performance and marking requirements and test methods for conventional, spray, flat spray and sidewall sprinklers. It is not applicable to sprinklers having multiple orifices.</p>"

56548,IS,,ISO 6182-1:2014,Fire protection — Automatic sprinkler systems — Part 1: Requirements and test methods for sprinklers,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 1: Prescriptions et méthodes d'essai des sprinklers,2014-01-06,3,['13.220.20'],ISO/TC 21/SC 5,9599,[38680],[74518],['en'],68,"<p>ISO 6182-1:2014 specifies performance and marking requirements and test methods for conventional, spray, flat spray, and sidewall sprinklers. It is not applicable to sprinklers having multiple orifices.</p>"

31662,IS,,ISO 6182-10:2006,Fire protection — Automatic sprinkler systems — Part 10: Requirements and test methods for domestic sprinklers,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 10: Exigences et méthodes d'essai des sprinklers domestiques,2006-02-09,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[56731],['en'],42,"<p>ISO 6182-10:2006 specifies performance requirements, test methods and marking requirements for domestic sprinklers.</p><p>These sprinklers are intended to provide control of fires in domestic occupancies, to prevent flashover (total involvement) in the room of fire origin and to improve the probability for successful escape or evacuatio

31663,IS,,ISO 6182-11:2003,Fire protection — Automatic sprinkler systems — Part 11: Requirements and test methods for pipe hangers,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 11: Exigences et méthodes d'essai relatives aux dispositifs de fixation des conduites,2003-12-02,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[68537],['en'],13,"<p>ISO 6182-11:2003 specifies performance requirements, test methods and marking requirements for pipe hangers.</p>"

39633,IS,,ISO 6182-12:2010,Fire protection — Automatic sprinkler systems — Part 12: Requirements and test methods for grooved-end components for steel pipe systems,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 12: Exigences et méthodes d'essai pour les raccords de tuyauterie en acier à extrémités rainurées,2010-01-04,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[64257],['en'],15,"<p>ISO 6182-12:2010 specifies performance requirements, grooving dimensions, test methods and marking requirements for couplings used in the joining of roll and cut grooved steel tube, pipe, grooved-end fittings and other grooved-end components up to 300 mm in nominal diameter.

64257,IS,,ISO 6182-12:2014,Fire protection — Automatic sprinkler systems — Part 12: Requirements and test methods for grooved-end components for steel pipe systems,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 12: Exigences et méthodes d'essai pour les raccords de tuyauterie en acier à extrémités rainurées,2014-12-11,2,['13.220.20'],ISO/TC 21/SC 5,9599,[39633],[69493],['en'],16,"<p>ISO 6182-12:2014 specifies performance requirements, grooving dimensions, test methods, and marking requirements for couplings used in the joining of roll and cut grooved steel tube, pipe, grooved-end fittings, and other grooved-end components up to 300 mm in nominal

12433,IS,,ISO 6182-2:1993,"Fire protection — Automatic sprinkler systems — Part 2: Requirements and test methods for wet alarm valves, retard chambers and water motor alarms","Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 2: Prescriptions et méthodes d'essai des soupapes d'alarme hydrauliques, des limiteurs de surpression et des dispositifs d'alarme à moteur hydraulique",1993-06-17,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[39620],"['en','fr']",15,"<p>Gives performance and other requirements, recommendations, and tests for wet alarm valves, retard chambers, water motor alarms and relevant trim, as specified by the manufacturers. Performance and test

39620,IS,,ISO 6182-2:2005,"Fire protection — Automatic sprinkler systems — Part 2: Requirements and test methods for wet alarm valves, retard chambers and water motor alarms","Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 2: Exigences et méthodes d'essai des soupapes d'alarme hydrauliques, des limiteurs de surpression et des dispositifs d'alarme à moteur hydraulique",2005-10-27,2,['13.220.20'],ISO/TC 21/SC 5,9599,[12433],[55812],['en'],22,"<p>ISO 6182-2:2005 specifies performance, requirements, methods of test and marking requirements, for wet alarm valves, retard chambers, water motor alarms and manufacturers' specified relevant trim used in we

55812,IS,,ISO 6182-2:2012,"Fire protection — Automatic sprinkler systems — Part 2: Requirements and test methods for wet alarm valves, retard chambers and water motor alarms","Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 2: Exigences et méthodes d'essai des soupapes d'alarme hydrauliques, des limiteurs de surpression et des dispositifs d'alarme à moteur hydraulique",2012-12-06,3,['13.220.20'],ISO/TC 21/SC 5,9599,[39620],[87735],['en'],20,"<p>ISO 6182-2:2012 specifies performance, requirements, methods of test and marking requirements, for wet alarm valves, retard chambers, water motor alarms and manufacturers' specified relevant trim used in we

12434,IS,,ISO 6182-3:1993,Fire protection — Automatic sprinkler systems — Part 3: Requirements and test methods for dry pipe valves,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 3: Prescriptions et méthodes d'essai des postes de contrôle sous air,1993-06-17,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[39629],"['en','fr']",13,"<p>Gives performance and other requirements, recommendations, and tests for dry pipe valves and relevant trim, as specified by the manufacturers. Performance and test requirements for other auxiliary components or attachments are not covered.</p>"

39629,IS,,ISO 6182-3:2005,Fire protection — Automatic sprinkler systems — Part 3: Requirements and test methods for dry pipe valves,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 3: Exigences et méthodes d'essai des postes de contrôle sous air,2005-10-27,2,['13.220.20'],ISO/TC 21/SC 5,9599,[12434],[55813],['en'],20,"<p>ISO 6182-3:2005 specifies performance, requirements, methods of test and marking requirements, for dry pipe valves and manufacturers' specified relevant trim used in dry pipe automatic fire protection systems.</p><p>Performance and test requirements for other auxiliary components or attachments to dry pipe valves are not covered by

55813,IS,,ISO 6182-3:2012,Fire protection — Automatic sprinkler systems — Part 3: Requirements and test methods for dry pipe valves,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 3: Exigences et méthodes d'essai des postes de contrôle sous air,2012-12-06,3,['13.220.20'],ISO/TC 21/SC 5,9599,[39629],"[68538,87735]",['en'],19,"<p>ISO 6182-3:2012 specifies performance, requirements, methods of test and marking requirements, for dry pipe valves and manufacturer's specified relevant trim used in dry pipe automatic fire protection systems.</p><p>Performance and test requirements for other auxiliary components or attachments to dry pipe valves are not co

12435,IS,,ISO 6182-4:1993,Fire protection — Automatic sprinkler systems — Part 4: Requirements and test methods for quick-opening devices,Protection contre l'incendie — Systèmes d'extinction automatique du type sprinkler — Partie 4: Prescriptions et méthodes d'essai des dispositifs à ouverture rapide,1993-08-26,1,['13.220.20'],ISO/TC 21/SC 5,9599,,"[68536,46498]","['en','fr']",6,<p>Specifies the performance and testing requirements for quick-opening devices used with dry pipe valves in fire protection systems to hasten the operation of the valves when one or more sprinklers operate. The quick-opening devices include accelerators and exhausters for use with specific dry pipe valves.</p> 12436

68536,IS,,ISO 6182-4:2019,Fire protection — Automatic sprinkler systems — Part 4: Requirements and test methods for quick opening devices,Protection contre l'incendie — Systèmes d'extinction automatique du type sprinkler — Partie 4: Exigences et méthodes d'essai des dispostifs a ouverture rapide,2019-02-26,2,['13.220.20'],ISO/TC 21/SC 5,9599,[12435],[87735],['en'],8,<p>This document specifies the performance and testing requirements for accelerators used with dry pipe valves in fire protection systems to hasten the operation of the valves when one or more sprinklers operate.</p>

12436,IS,,ISO 6182-5:1995,Fire protection — Automatic sprinkler systems — Part 5: Requirements and test methods for deluge valves,Protection contre l'incendie — Systèmes d'extinction automatiques de type sprinkler — Partie 5: Prescriptions et méthodes d'essai des postes déluges,1995-11-16,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[39630],"['en','fr']",12,<p>Specifies performance and test requirements for deluge valves employed in deluge and fire protection systems.</p>

39630,IS,,ISO 6182-5:2006,Fire protection — Automatic sprinkler systems — Part 5: Requirements and test methods for deluge valves,Protection contre l'incendie — Systèmes d'extinction automatiques de type sprinkler — Partie 5: Exigences et méthodes d'essai des postes déluges,2006-03-08,2,['13.220.20'],ISO/TC 21/SC 5,9599,[12436],[55875],['en'],19,"<p>ISO 6182-5:2006 specifies performance requirements, methods of test and marking requirements for deluge valves and manufacturers' specified relevant trim used in deluge and pre-action automatic fire protection systems. Deluge valves covered by these requirements can be operated by hydraulic, pneumatic, electric, mechanical, manual, or thermal mea

55875,IS,,ISO 6182-5:2012,Fire protection — Automatic sprinkler systems — Part 5: Requirements and test methods for deluge valves,Protection contre l'incendie — Systèmes d'extinction automatiques de type sprinkler — Partie 5: Exigences et méthodes d'essai des postes déluges,2012-12-06,3,['13.220.20'],ISO/TC 21/SC 5,9599,[39630],[87735],['en'],19,"<p>ISO 6182-5:2012 specifies performance requirements, methods of test and marking requirements for deluge valves and manufacturer's specified relevant trim used in deluge and pre-action automatic fire protection systems. Deluge valves covered by these requirements can be operated by hydraulic, pneumatic, electric, mechanical, manual, or thermal mea

39631,IS,,ISO 6182-6:2006,Fire protection — Automatic sprinkler systems — Part 6: Requirements and test methods for check valves,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 6: Exigences et méthodes d'essai des postes de contrôle,2006-03-08,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[68757],['en'],13,"<p>ISO 6182-6:2006 specifies performance requirements, methods of test and marking requirements for check valves used in automatic fire protection systems.</p>"

68757,IS,,ISO 6182-6:2020,Fire protection — Automatic sprinkler systems — Part 6: Requirements and test methods for check valves,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 6: Exigences et méthodes d'essai des postes de contrôle,2020-03-27,2,['13.220.20'],ISO/TC 21/SC 5,9599,[39631],[87735],['en'],12,"<p>This document specifies performance, requirements, test methods and marking requirements, for check valves used to supply water in automatic fire protection systems.</p><p>It is not applicable to trim valves.</p>"

28964,IS,,ISO 6182-7:2004,Fire protection — Automatic sprinkler systems — Part 7: Requirements and test methods for early suppression fast response (ESFR) sprinklers,Protection contre l'incendie — Systèmes d'extinction automatiques du type sprinkler — Partie 7: Prescriptions et méthodes d'essai des sprinklers de type 'extinction précoce/réaction rapide',2004-03-31,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[68758],['en'],40,"<p>ISO 6182-7:2004 specifies performance requirements, test methods and marking requirements for fusible element and glass-bulb early suppression fast response (ESFR) sprinklers. It is applicable to ESFR sprinklers with flow constants of 202 ± 8. </p>"

39632,IS,,ISO 6182-8:2006,Fire protection — Automatic sprinkler systems — Part 8: Requirements and test methods for pre-action dry alarm valves,Protection contre l'incendie — Systèmes d'extinction automatique du type sprinkler — Partie 8: Exigences et méthodes d'essai des postes de préalarme sous air,2006-03-08,1,['13.220.20'],ISO/TC 21/SC 5,9599,,[68535],['en'],22,"<p>ISO 6182-8:2006 specifies performance requirements, methods of test and marking requirements for pre-action dry alarm valves and manufacturers' specified relevant trim used in non-interlock pre-action automatic fire protection systems.</p><p>Performance and test requirements for other auxiliary components or attachments to pre

68535,IS,,ISO 6182-8:2019,Fire protection — Automatic sprinkler systems — Part 8: Requirements and test methods for pre-action dry alarm valves,Protection contre l'incendie — Systèmes d'extinction automatique du type sprinkler — Partie 8: Exigences et méthodes d'essai des postes de préalarme sous air,2019-05-29,2,['13.220.20'],ISO/TC 21/SC 5,9599,[39632],[87735],['en'],24,"<p>This document specifies performance requirements, methods of test and marking requirements for pre-action dry alarm valves, valve sets and manufacturers' specified relevant trim used in non-interlock pre-action automatic fire protection systems. Performance and test requirements for other auxiliary components or attachm

12437,IS,,ISO 6183:1990,Fire protection equipment — Carbon dioxide extinguishing systems for use on premises — Design and installation,Équipement de protection contre l'incendie — Installations fixes d'extinction par dioxyde de carbone utilisées dans les bâtiments — Conception et installation,1990-06-28,1,['13.220.10'],ISO/TC 21/SC 5,9599,,[50545],"['en','fr']",22,