Withdrawn and superseded ISO standards — page 135 of 246

11829,IS,,ISO 5721:1981,Agricultural tractors — Operator's field of vision,Tracteurs agricoles — Champ de visibilité du conducteur,1981-08-01,1,['65.060.10'],ISO/TC 23/SC 3,9599,,[11830],"['en','fr']",7,

11830,IS,,ISO 5721:1989,Tractors for agriculture — Operator's field of vision,Tracteurs agricoles — Champ de visibilité du conducteur,1989-10-12,2,['65.060.10'],ISO/TC 23/SC 4,9599,[11829],"[56751,71008,56752]","['en','fr']",7,"<p>This second edition cancels and replaces the first edition (1981). Specifies practical and mathematical methods of determining the masking effects of obstruction on the angles of vision forward, to the rear and upwards of seated operators of tractors. It does not take account of detachable implements and mounted elements, for example front loaders, pallets, ect.</p>"

11833,IS,,ISO 5725-1:1994,Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 1: Principes généraux et définitions,1994-12-22,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,[11832],[69418],"['en','fr']",17,"<p>The purpose is to outline the general principles to be understood when assessing accuracy (trueness and precision) of measurement methods and results, and in applications, and to establish practical estimations of the various measures by experiment. Is concerned exclusively with measurement methods which yield measurements on a continuous scale an

29779,IS,Cor,ISO 5725-1:1994/Cor 1:1998,Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions — Technical Corrigendum 1,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 1: Principes généraux et définitions — Rectificatif technique 1,1998-02-05,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,,[69418],"['en','fr']",2,

11831,IS,,ISO 5725:1981,Precision of test methods — Determination of repeatability and reproducibility by inter-laboratory tests,Fidélité des méthodes d'essai — Détermination de la répétabilité et de la reproductibilité par essais interlaboratoires,1981-04-01,1,['03.120.30'],ISO/TC 69,9599,,[11832],"['en','fr']",42,

11832,IS,,ISO 5725:1986,Precision of test methods — Determination of repeatability and reproducibility for a standard test method by inter-laboratory tests,Fidélité des méthodes d'essai — Détermination de la répétabilité et de la reproductibilité d'une méthode d'essai normalisée par essais interlaboratoires,1986-09-18,2,['03.120.30'],ISO/TC 69/SC 6,9599,[11831],"[11837,11834,11835,11836,11833,1384]","['en','fr']",49,

11834,IS,,ISO 5725-2:1994,Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 2: Méthode de base pour la détermination de la répétabilité et de la reproductibilité d'une méthode de mesure normalisée,1994-12-22,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,[11832],"[59570,69419]","['en','fr']",42,"<p>Amplifies the general principles to be observed in designing experiments for the numerical estimation of the precision of measurement methods by means of a collaborative interlaboratory e

36202,IS,Cor,ISO 5725-2:1994/Cor 1:2002,Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method — Technical Corrigendum 1,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 2: Méthode de base pour la détermination de la répétabilité et de la reproductibilité d'une méthode de mesure normalisée — Rectificatif technique 1,2002-06-06,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,,[69419],"['en','fr']",2,

69419,IS,,ISO 5725-2:2019,Accuracy (trueness and precision) of measurement methods and results — Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 2: Méthode de base pour la détermination de la répétabilité et de la reproductibilité d'une méthode de mesure normalisée,2019-12-06,2,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,"[11834,36202]",[90054],"['en','fr']",69,"<p><b>1.1</b> This document</p><p>— amplifies the general principles for designing experiments for the numerical estimation of the precision of measurement methods by means of a collabo

11835,IS,,ISO 5725-3:1994,Accuracy (trueness and precision) of measurement methods and results — Part 3: Intermediate measures of the precision of a standard measurement method,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 3: Mesures intermédiaires de la fidélité d'une méthode de mesure normalisée,1994-12-22,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,[11832],"[59570,69420]","['en','fr']",25,"<p>Specifies four intermediate measures due to changes in observation conditions (time, calibration, operator and equipment) within a laboratory. These intermediate measures can be established by an experiment within a specific laboratory or by an interlaboratory expe

36203,IS,Cor,ISO 5725-3:1994/Cor 1:2001,Accuracy (trueness and precision) of measurement methods and results — Part 3: Intermediate measures of the precision of a standard measurement method — Technical Corrigendum 1,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 3: Mesures intermédiaires de la fidélité d'une méthode de mesure normalisée — Rectificatif technique 1,2001-10-25,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,,[69420],"['en','fr']",1,

11836,IS,,ISO 5725-4:1994,Accuracy (trueness and precision) of measurement methods and results — Part 4: Basic methods for the determination of the trueness of a standard measurement method,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 4: Méthodes de base pour la détermination de la justesse d'une méthode de mesure normalisée,1994-12-22,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,[11832],"[59570,69421]","['en','fr']",23,"<p>Provides basic methods for estimating the bias of a measurement method and the laboratory bias when a measurement method is applied. In order that the measurements are made in the same way, it is important that the measurement method ha

1384,IS,,ISO 5725-5:1998,Accuracy (trueness and precision) of measurement methods and results — Part 5: Alternative methods for the determination of the precision of a standard measurement method,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 5: Méthodes alternatives pour la détermination de la fidélité d'une méthode de mesure normalisée,1998-07-23,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,[11832],"[79066,69422]","['en','fr']",56,

42913,IS,Cor,ISO 5725-5:1998/Cor 1:2005,Accuracy (trueness and precision) of measurement methods and results — Part 5: Alternative methods for the determination of the precision of a standard measurement method — Technical Corrigendum 1,Exactitude (justesse et fidélité) des résultats et méthodes de mesure — Partie 5: Méthodes alternatives pour la détermination de la fidélité d'une méthode de mesure normalisée — Rectificatif technique 1,2005-08-22,1,"['03.120.30','17.020']",ISO/TC 69/SC 6,9599,,"[79066,69422]","['en','fr']",1,

11844,IS,,ISO 5734:1978,Test conditions of mechanical dividing heads for machine tools — Testing of the accuracy,"Conditions d'essais des appareils diviseurs, à commande mécanique, pour machines-outils — Contrôle de la précision",1978-03-01,1,['25.060.20'],ISO/TC 39,9599,,[11845],"['en','fr']",7,

11848,IS,,ISO 5738:1980,Milk and milk products — Determination of copper content — Photometric reference method,Lait et produits laitiers — Détermination de la teneur en cuivre — Méthode photométrique de référence,1980-10-01,1,['67.100.01'],ISO/TC 34/SC 5,9599,,[36913],"['en','fr']",6,"<p>Applies to milk, skimmed milk, whey, buttermilk, evaporated milk, sweetened condensed milk, dried whole and skimmed milk, cream and butter, butterfat, ice-cream, hard, semi-hard and soft cheese of various ages and processed cheese, caseins, caseinates and coprecipitates. The principle of determination consists in digesting the organic material with a mixture of nitric and sulfuric acids and neutralizing wit

11849,IS,,ISO 5739:1983,Caseins and caseinates — Determination of scorched particles content,Caséines et caséinates — Détermination de la teneur en particules brûlées,1983-09-01,1,['67.100.99'],ISO/TC 34/SC 5,9599,,"[31878,11850]","['en','fr']",8,"<p>Specifies a method on the principle of dissolution of a test portion in hot sodium carbonate, sodium polyphosphate or disodium ethylenediaminetetraacetate solution, or in sodium hydroxide solution at room temperature or at 60 degrees centigrade, filtration of the solution through a filtering disk and visual comparison of dried disk with scorched particle standard disks. The testing of filtering disks is described in Annex A and Annex B gives inf

4666,IS,,ISO 574:1979,Textile machinery and accessories — Perforated cylindrical tubes for cheese dyeing,Matériel pour l'industrie textile — Tubes cylindriques perforés pour teinture,1979-02-01,1,['59.120.20'],ISO/TC 72/SC 1,9599,,[9546],"['en','fr']",1,

11852,IS,,ISO 5742:1982,Pliers and nippers — Nomenclature,Pinces et tenailles — Nomenclature,1982-12-01,1,"['25.140.30','01.040.25']",ISO/TC 29/SC 10,9599,,[33638],"['en','fr','ru']",15,"<p>The figures in ISO 5742 are only examples, and are not intended to affect the manufacturer' s design. Gives terms relating to cutting nippers, gripping pliers, combined gripping and cutting pliers, component parts, handles, joints for closing pliers, joints for operning pliers, features of head, cutters, cutting edges, shape of nose and gripping surface in English, French and Russian and in an annex also in German, Italian and Spanish.</p>"

11853,IS,Add,ISO 5742:1982/Add 1:1985,Pliers and nippers — Nomenclature — Addendum 1,Pinces et tenailles — Nomenclature — Additif 1,1985-04-25,1,"['25.140.30','01.040.25']",ISO/TC 29,9599,,[33638],"['en','fr','ru']",4,

11854,IS,,ISO 5743:1982,Pliers and nippers — General technical requirements,Pinces et tenailles — Spécifications techniques générales,1982-09-01,1,['25.140.30'],ISO/TC 29,9599,,[11855],"['en','fr']",1,

11855,IS,,ISO 5743:1988,Pliers and nippers — General technical requirements,Pinces et tenailles — Spécifications techniques générales,1988-09-29,2,['25.140.30'],ISO/TC 29/SC 10,9599,[11854],[33639],"['en','fr']",2,

33639,IS,,ISO 5743:2004,Pliers and nippers — General technical requirements,Pinces et tenailles — Spécifications techniques générales,2004-09-29,3,['25.140.30'],ISO/TC 29/SC 10,9599,[11855],[79499],"['en','fr']",3,<p>ISO 5743:2004 specifies the general technical requirements to be met by pliers and nippers. It does not specify insulating or antistatic characteristics of handle coatings. Plastic coatings or plastic sleeves are intended for gripping comfort only.</p><p>ISO 5743:2004 is only applicable to pliers for which ISO standards exist.</p>

11856,IS,,ISO 5744:1983,Pliers and nippers — Methods of test,Pinces et tenailles — Méthodes d'essai,1983-12-01,1,['25.140.30'],ISO/TC 29,9599,,[11857],"['en','fr']",5,

11857,IS,,ISO 5744:1988,Pliers and nippers — Methods of test,Pinces et tenailles — Méthodes d'essai,1988-09-01,2,['25.140.30'],ISO/TC 29/SC 10,9599,[11856],[33640],"['en','fr']",6,"<p>This secon edition cancels and replaces the first edition (ISO 5744:1983). checks the correct functioning of pliers and nippers.The test parameters habe been specified on the basis of the functional uses of the tools. Gives load test, wire cutting test, torsion test, soft wire cutting test and hardness of gripping surfaces.</p>"

11858,IS,,ISO 5745:1982,Pliers and nippers — Pliers for gripping and manipulating — Dimensions,Pinces et tenailles — Pinces de serrage et de manipulation — Dimensions,1982-09-01,1,['25.140.30'],ISO/TC 29,9599,,[11859],"['en','fr']",5,

11859,IS,,ISO 5745:1988,Pliers and nippers — Pliers for gripping and manipulating — Dimensions and test values,Pinces et tenailles — Pinces de serrage et de manipulation — Dimensions et valeurs d'essai,1988-10-27,2,['25.140.30'],ISO/TC 29/SC 10,9599,[11858],[33641],"['en','fr']",5,<p>This second edition cancels and replaces the first edition (ISO 5745:1982). specifies the principal dimensions of these pliers and the test values in order to verify their aplitude to function in conformity with ISO 5744. General technical requirements: see ISO 5743. The figures in ISO 5745 are examples only and are not intended to affect the manufactuere' s design.</p>

11860,IS,,ISO 5746:1982,Pliers and nippers — Engineer's and lineman's pliers — Dimensions,Pinces et tenailles — Pinces universelles et pinces 'lineman's' — Dimensions,1982-09-01,1,['25.140.30'],ISO/TC 29,9599,,[11861],"['en','fr']",3,

11861,IS,,ISO 5746:1988,Pliers and nippers — Engineer's and lineman's pliers — Dimensions and test values,Pinces et tenailles — Pinces universelles et pinces 'lineman's' — Dimensions et valeurs d'essai,1988-10-13,2,['25.140.30'],ISO/TC 29/SC 10,9599,[11860],[33642],"['en','fr']",4,<p>This second edition cancels and replaces the first edition (ISO 5746:1982). specifies the principal dimensions of these pliers and the test values in order to verify their aplitude to function in conformity with ISO 5744. General technical requirements: see ISO 5743. The figures in ISO 5746 are examples only and are not intended to affect the manufactuere' s design.</p>

33642,IS,,ISO 5746:2004,Pliers and nippers — Engineer's and 'Lineman's' pliers — Dimensions and test values,Pinces et tenailles — Pinces universelles et pinces 'Lineman's' — Dimensions et valeurs d'essai,2004-09-29,3,['25.140.30'],ISO/TC 29/SC 10,9599,[11861],[79500],"['en','fr']",6,<p>ISO 5746:2004 specifies the principal dimensions of engineer's and lineman's pliers and the test values for the pliers in order to verify their aptitude to function in conformity with ISO 5744:2004. General technical requirements are given in ISO 5743:2004.</p>

11862,IS,,ISO 5747:1984,"Pliers and nippers — Lever assisted side cutting pliers, end and diagonal cutting nippers — Dimensions","Pinces et tenailles — Pinces articulées coupantes de côté, coupantes en bout et coupantes diagonale — Dimensions",1984-12-01,1,['25.140.30'],ISO/TC 29,9599,,[22896],"['en','fr']",4,

11863,IS,,ISO 5748:1982,Pliers and nippers — End cutting nippers — Dimensions,Pinces et tenailles — Pinces coupantes en bout — Dimensions,1982-09-01,1,['25.140.30'],ISO/TC 29,9599,,[11864],"['en','fr']",5,

11864,IS,,ISO 5748:1988,Pliers and nippers — End cutting nippers — Dimensions and test values,Pinces et tenailles — Pinces coupantes en bout — Dimensions et valeurs d'essai,1988-10-13,2,['25.140.30'],ISO/TC 29/SC 10,9599,[11863],[33643],"['en','fr']",4,<p>This second edition cancels and replaces the first edition (ISO 5748:1982). Specifies the principal dimensions of end cutting nippers and the test values in order to verify their aptitude to function in conformity with ISO 5744. general technical requirements: see ISO 5743. The figures in ISO 5748 are examples only and are not intended to affect the manufactuere's design.</p>

11866,IS,,ISO 5749:1982,Pliers and nippers — Diagonal cutting nippers — Dimensions,Pinces et tenailles — Pinces coupantes diagonales — Dimensions,1982-12-01,1,['25.140.30'],ISO/TC 29,9599,,[11867],"['en','fr']",3,

11868,IS,Add,ISO 5749:1982/Add 1:1984,Pliers and nippers — Diagonal cutting nippers — Dimensions — Addendum 1,Pinces et tenailles — Pinces coupantes diagonales — Dimensions — Additif 1,1984-12-01,1,['25.140.30'],ISO/TC 29,9599,,[11867],['en'],1,

11867,IS,,ISO 5749:1988,Pliers and nippers — Diagonal cutting nippers — Dimensions and test values,Pinces et tenailles — Pinces coupantes diagonale — Dimensions et valeurs d'essai,1988-10-13,2,['25.140.30'],ISO/TC 29/SC 10,9599,"[11868,11866]",[33644],"['en','fr']",4,

11869,IS,,ISO 5751-1:1983,Motorcycle tyres and rims (metric series) — Part 1: Tyres — All series,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 1: Pneumatiques toutes séries,1983-08-01,2,['83.160.10'],ISO/TC 31/SC 10,9599,,"[11870,11871]","['en','fr']",6,

11870,IS,,ISO 5751-1:1988,"Motorcycle tyres and rims (metric series) — Part 1: Tyres, all series",Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 1: Pneumatiques toutes séries,1988-11-24,3,['83.160.10'],ISO/TC 31/SC 10,9599,[11869],[11871],"['en','fr']",7,

11871,IS,,ISO 5751-1:1994,Motorcycle tyres and rims (metric series) — Part 1: Design guides,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 1: Guide de conception,1994-12-22,4,['83.160.10'],ISO/TC 31/SC 10,9599,"[11870,11869]",[33413],"['en','fr']",9,"<p>Specifies design guides, designation, dimensions and load-carrying capacity of the metric series of motorcycle tyres. Applies to motorcycle tyres with reduced height/width ratio (100 and lower), that can be fitted on cylindrical bead seat rims or 5° tapered bead seat rims. Is also applicable to different concepts of tyres and rims. In this case, however, appropriate coefficients will be established. ISO 4249 deals wit

28795,IS,Amd,ISO 5751-1:1994/Amd 1:1999,Motorcycle tyres and rims (metric series) — Part 1: Design guides — Amendment 1,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 1: Guide de conception — Amendement 1,1999-04-15,4,['83.160.10'],ISO/TC 31/SC 10,9599,,[33413],"['en','fr']",3,

33413,IS,,ISO 5751-1:2001,Motorcycle tyres and rims (metric series) — Part 1: Design guides,Pneumatiques et jantes pour motocycles (série millimétrique) — Partie 1: Guide de conception,2001-12-20,5,['83.160.10'],ISO/TC 31/SC 10,9599,"[28795,11871]",[37791],['en'],14,

37791,IS,,ISO 5751-1:2004,Motorcycle tyres and rims (metric series) — Part 1: Design guides,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 1: Guide de conception,2004-11-24,6,"['43.140','83.160.10']",ISO/TC 31/SC 10,9599,[33413],[51734],"['en','fr']",14,"<p>ISO 5751-1:2004 gives guidelines for the design of, and specifies the designation and calculation of the dimensions for, metric-series motorcycle tyres. It is applicable to motorcycle tyres with a reduced height/width ratio (100 and lower) that can be fitted on cylindrical bead-seat or 5° tapered bead-seat rims. It is also applicable to other concepts of tyre and rim, provided the appropriate rim/section ratios an

44499,IS,Cor,ISO 5751-1:2004/Cor 1:2006,Motorcycle tyres and rims (metric series) — Part 1: Design guides — Technical Corrigendum 1,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 1: Guide de conception — Rectificatif technique 1,2006-07-07,6,"['43.140','83.160.10']",ISO/TC 31/SC 10,9599,,[51734],"['en','fr']",1,

11872,IS,,ISO 5751-2:1983,"Motorcycle tyres and rims (metric series) — Part 2: Tyre series 80, 90 and 100","Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 2: Pneumatiques des séries 80, 90 et 100",1983-06-01,1,['83.160.10'],ISO/TC 31/SC 10,9599,,"[11873,11874]","['en','fr']",7,

11873,IS,,ISO 5751-2:1988,"Motorcycle tyres and rims (metric series) — Part 2: Tyre series 100, 90, 80, 70 and 60","Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 2: Pneumatiques des séries 100, 90, 80, 70 et 60",1988-11-24,2,['83.160.10'],ISO/TC 31/SC 10,9599,[11872],[11874],"['en','fr']",13,

11874,IS,,ISO 5751-2:1994,Motorcycle tyres and rims (metric series) — Part 2: Tyre dimensions and load-carrying capacities,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 2: Cotes et capacités de charge des pneumatiques,1994-12-22,3,['83.160.10'],ISO/TC 31/SC 10,9599,"[11873,11872]",[33414],"['en','fr']",23,"<p>Specifies the designation, dimensions and load-carrying capacity of metric series 100, 90, 80, 70, 60, 55 and 50 motorcycle tyres to be mounted on the metric series of rims. Applies to motorcycle tyres with reduced height/width ratio (low profile). ISO 4249 deals with the requirements for motorcycle tyres and rims (code-designated series) for rim diameters code

27524,IS,Amd,ISO 5751-2:1994/Amd 1:1997,Motorcycle tyres and rims (metric series) — Part 2: Tyre dimensions and load-carrying capacities — Amendment 1,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 2: Cotes et capacités de charge des pneumatiques — Amendement 1,1997-12-25,3,['83.160.10'],ISO/TC 31/SC 10,9599,,[33414],"['en','fr']",7,

33414,IS,,ISO 5751-2:2002,Motorcycle tyres and rims (metric series) — Part 2: Tyre dimensions and load-carrying capacities,Pneumatiques et jantes pour motocycles (série millimétrique) — Partie 2: Cotes et capacités de charge des pneumatiques,2002-03-14,4,['83.160.10'],ISO/TC 31/SC 10,9599,"[11874,27524]",[37792],['en'],25,"<p>This part of ISO 5751 specifies the tyre size designation, dimensions and load-carrying capacities of metric-series motorcycle tyres.</p><p>It is applicable to metric-series motorcycle tyres with a height-to-width width ratio of 100 % and below.</p><p>NOTE See ISO 4249 for the requirements on motorcycle tyres and rims (code-designated series) for rim diameters code 13 a

37792,IS,,ISO 5751-2:2004,Motorcycle tyres and rims (metric series) — Part 2: Tyre dimensions and load-carrying capacities,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 2: Cotes et capacités de charge des pneumatiques,2004-11-24,5,"['43.140','83.160.10']",ISO/TC 31/SC 10,9599,[33414],[51735],"['en','fr']",30,"<p>ISO 5751-2:2004 specifies the tyre size designation, dimensions and load-carrying capacities of metric-series motorcycle tyres. It is applicable to such tyres with a height-to-width ratio of 100 % and below.</p>"

11875,IS,,ISO 5751-3:1983,"Motorcycle tyres and rims (metric series) — Part 3: Rims for tyres of series 80, 90 and 100","Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 3: Jantes pour pneumatiques des séries 80, 90 et 100",1983-06-01,1,['43.140'],ISO/TC 31/SC 10,9599,,[11876],"['en','fr']",1,

11876,IS,,ISO 5751-3:1988,"Motorcycle tyres and rims (metric series) — Part 3: Rims for tyres of series 100, 90, 80, 70 and 60","Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 3: Jantes pour pneumatiques des séries 100, 90, 80, 70 et 60",1988-06-09,2,['43.140'],ISO/TC 31/SC 10,9599,[11875],[11842],"['en','fr']",1,

11842,IS,,ISO 5751-3:1994,Motorcycle tyres and rims (metric series) — Part 3: Range of approved rim contours,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 3: Gamme des profils de jante homologués,1994-12-22,3,['83.160.10'],ISO/TC 31/SC 10,9599,[11876],[27525],"['en','fr']",2,

27525,IS,,ISO 5751-3:1999,Motorcycle tyres and rims (metric series) — Part 3: Range of approved rim contours,Pneumatiques et jantes pour motocycles (série métrique) — Partie 3: Gamme des profils de jante homologués,1999-03-18,4,['43.140'],ISO/TC 31/SC 10,9599,[11842],[37793],"['en','fr']",2,

34472,IS,Amd,ISO 5751-3:1999/Amd 1:2002,Motorcycle tyres and rims (metric series) — Part 3: Range of approved rim contours — Amendment 1,Pneumatiques et jantes pour motocycles (série métrique) — Partie 3: Gamme des profils de jante homologués — Amendement 1,2002-03-07,4,['43.140'],ISO/TC 31/SC 10,9599,,[37793],"['en','fr']",2,

37793,IS,,ISO 5751-3:2004,Motorcycle tyres and rims (metric series) — Part 3: Range of approved rim contours,Pneumatiques et jantes pour motocycles (séries millimétriques) — Partie 3: Gamme des profils de jante homologués,2004-11-24,5,"['43.140','83.160.10']",ISO/TC 31/SC 10,9599,"[34472,27525]",[51736],"['en','fr']",5,<p>ISO 5751-3:2004 specifies the approved rim contours for the rims on which metric-series motorcycle tyres are mounted.</p>

11877,IS,,ISO 5752:1982,Metal valves for use in flanged pipe systems — Face-to-face and centre-to-face dimensions,Appareils de robinetterie métalliques utilisés dans les tuyauteries à brides — Dimensions face-à-face et face-à-axe,1982-06-01,2,['23.060.01'],ISO/TC 153,9599,,"[21013,77335]","['en','fr']",11,"<p>Specifies the dimensions for two-way valves. Each basic series of these dimensions may be used as required with flanges of mating dimensions conforming to ISO 2084 or ISO 2229. The range of pressure ratings, in PN values, is from 1 up to and including 40, and the classes from 125 to 600; the range of nominal sizes, in DN values, is from 10 up to and including 2000. This second edition c

11878,IS,,ISO 5753:1981,Rolling bearings — Radial internal clearance,Roulements — Jeu interne radial,1981-06-01,1,['21.100.20'],ISO/TC 4,9599,"[6263,4493,4066,5514]",[11879],"['en','fr']",6,

11879,IS,,ISO 5753:1991,Rolling bearings — Radial internal clearance,Roulements — Jeu interne radial,1991-10-17,2,['21.100.20'],ISO/TC 4/SC 4,9599,[11878],[44742],"['en','fr']",6,<p>Specifies clearance values for: radial contact groove ball bearings; double row self-aligning ball bearings; cylindrical roller bearings; needle roller bearings; and double row self-aligning roller bearings. This second edition cancels and replaces the first edition (1981).</p>

11880,IS,,ISO 5754:1978,"Sintered metal materials, excluding hardmetals — Unnotched impact test piece","Matériaux métalliques frittés, à l'exclusion des métaux-durs — Éprouvette non entaillée pour essai de résilience",1978-02-01,1,"['77.160','77.040.10']",ISO/TC 119/SC 3,9599,,[69222],"['en','fr']",1,"<p>Specifies the dimensions of an unnotched impact test piece of sintered metal materials. The test piece may be obtained directly by pressing and sintering or by machining a sintered part. For certain materials with high ductility, it may be more appropriate to use a notched test piece.</p>"

69222,IS,,ISO 5754:2017,"Sintered metal materials, excluding hardmetals — Unnotched impact test piece","Matériaux métalliques frittés, à l'exclusion des métaux-durs — Éprouvette non entaillée pour essai de résilience",2017-10-04,2,"['77.160','77.040.10']",ISO/TC 119/SC 3,9599,[11880],[85821],"['en','fr']",2,"<p>ISO 5754 specifies the dimensions of an unnotched impact test piece of sintered metal materials. The test piece may be obtained directly by pressing and sintering or by machining a sintered part.</p><p>ISO 5754 applies to all sintered metals and alloys, with the exception of hardmetals. However, for certain materials (for example, materials with low porosity or materials with high duc

11881,IS,,ISO 5755-1:1986,"Sintered metal materials — Specifications — Part 1: Materials, for bearings, impregnated with liquid lubricant","Matériaux métalliques frittés — Spécifications — Partie 1: Matériaux, pour coussinets, imprégnés de lubrifiant liquide",1986-09-18,2,"['77.160','21.100.10']",ISO/TC 119,9599,,[11882],['fr'],,

11882,IS,,ISO 5755-1:1987,"Sintered metal materials — Specifications — Part 1: Materials, for bearings, impregnated with liquid lubricant","Matériaux métalliques frittés — Spécifications — Partie 1: Matériaux, pour coussinets, imprégnés de lubrifiant liquide",1987-09-10,3,"['77.160','21.100.10']",ISO/TC 119,9599,[11881],[24625],"['en','fr']",2,

24625,IS,,ISO 5755:1996,Sintered metal materials — Specifications,Matériaux métalliques frittés — Spécifications,1996-11-21,1,['77.160'],ISO/TC 119,9599,"[11882,11883,11884]",[27509],"['en','fr']",13,

11883,IS,,ISO 5755-2:1987,"Sintered metal materials — Specifications — Part 2: Sintered iron and sintered steel containing one or both of the elements carbon and copper, used for structural parts","Matériaux métalliques frittés — Spécifications — Partie 2: Fers frittés et aciers frittés contenant un ou deux des éléments carbone et cuivre, destinés à la fabrication de pièces mécaniques",1987-09-10,1,['77.160'],ISO/TC 119,9599,,[24625],"['en','fr']",3,

27509,IS,,ISO 5755:2001,Sintered metal materials — Specifications,Matériaux métalliques frittés — Spécifications,2001-05-03,2,['77.160'],ISO/TC 119,9599,[24625],[42225],"['en','fr']",19,

42225,IS,,ISO 5755:2012,Sintered metal materials — Specifications,Matériaux métalliques frittés — Spécifications,2012-08-20,3,['77.160'],ISO/TC 119/SC 5,9599,[27509],[82169],"['en','fr']",39,"<p>ISO 5755:2012 specifies the requirements for the chemical composition and the mechanical and physical properties of sintered metal materials used for bearings and structural parts.</p><p>When selecting powder metallurgical (PM) materials, it should be taken into account that the properties depend not only on the chemical composition and density, but also on the production methods. The properties of sintered materials giving satisfactory service in particular applications may not necessarily be the sa

11884,IS,,ISO 5755-3:1987,Sintered metal materials — Specifications — Part 3: Sintered alloyed and sintered stainless steels used for structural parts,Matériaux métalliques frittés — Spécifications — Partie 3: Aciers alliés et aciers inoxydables frittés destinés à la fabrication de pièces mécaniques,1987-09-10,1,['77.160'],ISO/TC 119,9599,,[24625],"['en','fr']",4,

11887,IS,,ISO 5758:1987,Cinematography — Labelling of containers for motion-picture film and magnetic materials — Minimum information for exchange of materials,Cinématographie — Étiquetage des conteneurs pour films cinématographiques et bandes magnétiques — Informations minimales pour les échanges de produits,1987-08-27,1,['37.060.20'],ISO/TC 36,9599,,"[25770,35512]","['en','fr']",3,<p>Specified is the information to be included on the label and/or accompanying documents for identifying the contents of containers for processed motion-picture films and magnetic sound records. The specifications do not apply to containers for unexposed motion-picture films nor magnetic materials specified in I

11889,IS,,ISO 5760:1980,"Cinematography — Sound motion-picture camera cartridge, 8 mm Type S, Model 1 — Aperture opening, pressure pad and film position — Dimensions and specifications","Cinématographie — Chargeur, modèle 1, pour caméra sonore 8 mm type S — Fenêtre, presseur et position du film — Dimensions et spécifications",1980-10-01,1,['37.060.10'],ISO/TC 36,9599,,[6413],"['en','fr']",5,

11890,IS,,ISO 5761:1980,"Cinematography — Sound motion-picture camera cartridge, 8 mm Type S, Model 1 — Pressure pad flatness and camera aperture profile — Dimensions and characteristics","Cinématographie — Chargeur, modèle 1, pour caméra sonore 8 mm type S — Planéité du presseur et profil de la fenêtre de la caméra — Dimensions et caractéristiques",1980-10-01,1,['37.060.10'],ISO/TC 36,9599,,[6413],"['en','fr']",3,

11891,IS,,ISO 5763:1982,Photography — Electronic flash equipment — Automatic control of exposure,Photographie — Équipement électronique à éclairs — Contrôle automatique de l'exposition,1982-12-01,1,['37.040.10'],ISO/TC 42,9599,,[11892],"['en','fr']",5,

11893,IS,,ISO 5764:1987,Milk — Determination of freezing point — Thermistor cryoscope method,Lait — Détermination du point de congélation — Méthode au cryoscope à thermistance,1987-05-21,1,['67.100.10'],ISO/TC 34/SC 5,9599,,[23538],"['en','fr']",6,"<p>Is applicable to raw, pasteurized UHT-treated or sterilized whole milk, partly skimmed and skimmed milk. The principle consists in supercooling a test portion of the milk to the appropriate temperature, depending on the instrument, and inducing the crystallizatin by mechanical vibration which causes the temperature to rise quickly to a level which corresponds to the freezing point ot the test portion. Annex A specifies the means of duplicate va

23538,IS,,ISO 5764:2002,Milk — Determination of freezing point — Thermistor cryoscope method (Reference method),Lait — Détermination du point de congélation — Méthode au cryoscope à thermistance (Méthode de référence),2002-06-06,2,['67.100.10'],ISO/TC 34/SC 5,9599,[11893],[43986],"['en','fr']",15,"<p>ISO 5764|IDF 108:2002 specifies a reference method for the determination of the freezing point of raw, pasteurized, UHT-treated or sterilized whole milk, partially skimmed milk and skimmed milk by using a thermistor cryoscope.</p><p>The freezing point can be used for estimating the proportion of extraneous water in milk. Calculation of the amount of extraneous water is complicated by daily varia

11895,IS,,ISO 5766:1978,Pallet stackers and high lift platform trucks — Stability tests,Chariots à fourche recouvrante et chariots à plate-forme à grande levée — Essais de stabilité,1978-12-01,1,['53.060'],ISO/TC 110/SC 2,9599,,[11896],"['en','fr']",7,

11896,IS,,ISO 5766:1990,Pallet stackers and high-lift platform trucks — Stability tests,Chariots à fourche recouvrante et chariots à plate-forme à grande levée — Essais de stabilité,1990-12-13,2,['53.060'],ISO/TC 110/SC 2,9599,[11895],"[36610,41213]","['en','fr']",8,

11897,IS,,ISO 5767:1978,Industrial trucks operating in special condition of stacking with mast tilted forward — Stability tests,"Chariots travaillant dans des conditions spéciales, avec mât incliné en avant — Essai de stabilité",1978-09-01,1,['53.060'],ISO/TC 110,9599,,[11898],"['en','fr']",2,

11898,IS,,ISO 5767:1992,Industrial trucks operating in special condition of stacking with mast tilted forward — Additional stability test,"Chariots de manutention travaillant dans des conditions de gerbage spéciales, avec le mât incliné en avant — Essai de stabilité supplémentaire",1992-09-03,2,['53.060'],ISO/TC 110/SC 2,9599,[11897],"[42348,30195]","['en','fr']",3,"<p>Applies to counterbalanced fork-lift trucks with tiltable masts, up to and including 50 000 kg rated capacity; reach and straddle fork-lift trucks with tiltable masts, up to and including 5 000 kg rated capacity; pallet stackers and high-lift platform trucks with tiltable masts, up to and including 5 000 kg rated capacity. Doe

30914,IS,Amd,ISO 5767:1992/Amd 1:1999,Industrial trucks operating in special condition of stacking with mast tilted forward — Additional stability test — Amendment 1,"Chariots de manutention travaillant dans des conditions de gerbage spéciales, avec le mât incliné en avant — Essai de stabilité supplémentaire — Amendement 1",1999-11-18,2,['53.060'],ISO/TC 110/SC 2,9599,,[42348],"['en','fr']",1,

11899,IS,,ISO 5768:1981,Cinematography — Image produced by camera aperture Type W on 16 mm motion-picture film — Position and dimensions,Cinématographie — Champ d'image enregistré par la caméra type W sur film cinématographique 16 mm — Position et dimensions,1981-08-01,1,['37.060.20'],ISO/TC 36,9599,,[25997],"['en','fr']",3,

11900,IS,Cor,ISO 5768:1981/Cor 1:1992,Cinematography — Image produced by camera aperture Type W on 16 mm motion-picture film — Position and dimensions — Technical Corrigendum 1,Cinématographie — Champ d'image enregistré par la caméra type W sur film cinématographique 16 mm — Position et dimensions — Rectificatif technique 1,1992-01-29,1,['37.060.20'],ISO/TC 36,9599,,[25997],"['en','fr']",1,

25997,IS,,ISO 5768:1996,Cinematography — Image produced by camera aperture Type W on 16 mm motion-picture film — Position and dimensions,Cinématographie — Champ d'image enregistré par caméra type W sur film cinématographique 16 mm — Position et dimensions,1996-11-28,2,['37.060.20'],ISO/TC 36,9599,"[11900,11899]",[30125],"['en','fr']",4,

11901,IS,,ISO 5769:1984,Photography — Processed films — Method for determining lubrication,Photographie — Films développés — Méthode de détermination de la présence d'un lubrifiant,1984-09-01,1,['37.040.20'],ISO/TC 42,9599,,[31928],"['en','fr']",7,

4671,IS,,ISO 577-3:1973,Withdrawal of ISO 477/3-1973,Annulation de l'ISO 477/3-1973,1973-04-01,1,['21.100.20'],ISO/TC 4,9599,,[4542],['en'],2,

11902,IS,,ISO 5771:1981,Rubber hose and hose assemblies for transferring anhydrous ammonia,Tuyaux et flexibles en caoutchouc pour le transfert d'ammoniac anhydre,1981-11-01,1,"['83.140','71.120.30']",ISO/TC 45/SC 1,9599,,[11903],"['en','fr']",5,

11903,IS,,ISO 5771:1994,Rubber hose and hose assemblies for transferring anhydrous ammonia — Specification,Tuyaux et flexibles en caoutchouc pour le transfert d'ammoniac anhydre — Spécifications,1994-10-06,2,"['83.140.40','71.120.99']",ISO/TC 45/SC 1,9599,[11902],[43694],"['en','fr']",7,"<p>Cancels and replaces the first edition (1981). Specifies the minimum requirements for rubber hose used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures between -40 °C and +55 °C. Does not include specifications for end fittings, but is limited to the performance of the hose and hose assemblies.</p>"

26277,IS,Cor,ISO 5771:1994/Cor 1:1995,Rubber hose and hose assemblies for transferring anhydrous ammonia — Specification — Technical Corrigendum 1,Tuyaux et flexibles en caoutchouc pour le transfert d'ammoniac anhydre — Spécifications — Rectificatif technique 1,1995-08-31,2,"['83.140.40','71.120.99']",ISO/TC 45/SC 1,9599,,[43694],"['en','fr']",1,<p>Corrects the requirement for the minimum burst pressure after flexing in table 2.</p>

43694,IS,,ISO 5771:2008,Rubber hoses and hose assemblies for transferring anhydrous ammonia — Specification,Tuyaux et flexibles en caoutchouc pour le transfert d'ammoniac anhydre — Spécifications,2008-09-03,3,"['83.140.40','71.120.99']",ISO/TC 45/SC 1,9599,"[11903,26277]",[84062],"['en','fr']",13,"<p>ISO 5771:2008 specifies the minimum requirements for rubber hoses used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures from - 40 °C up to and including + 55 °C. It does not include specifications for end fittings, but is limited to the performance of the hoses and hose assemblies.</p>"

11904,IS,,ISO 5772-1:1986,Rubber hoses — Measured fuel dispensing — Part 1: Conventional petroleum based fuels — Specification,Tuyaux en caoutchouc — Distribution de carburant mesuré — Partie 1: Carburants à base de pétrole conventionnel — Spécifications,1986-06-12,1,"['83.140.40','75.200']",ISO/TC 45/SC 1,9599,,[20161],"['en','fr']",4,

20161,IS,,ISO 5772:1998,Rubber hoses and hose assemblies for measured fuel dispensing — Specification,Tuyaux et flexibles en caoutchouc pour distribution mesurée de carburants — Spécification,1998-12-17,1,"['83.140.40','75.200']",ISO/TC 45/SC 1,9599,[11904],[57302],['en'],8,

11905,IS,,ISO 5774:1980,Plastics hoses — Textile-reinforced thermoplastics type for compressed air — Specification,Tuyaux en plastiques — Type en thermoplastique armé de textile pour l'air comprimé — Spécifications,1980-02-01,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[11906],"['en','fr']",2,

11906,IS,,ISO 5774:1997,Plastics hoses — Textile-reinforced types for compressed-air applications — Specification,Tuyaux en plastique armés de textile pour l'air comprimé — Spécifications,1997-07-24,2,['23.040.70'],ISO/TC 45/SC 1,9599,[11905],[41420],"['en','fr']",6,

41420,IS,,ISO 5774:2006,Plastics hoses — Textile-reinforced types for compressed-air applications — Specification,Tuyaux en plastique — Types armés de textile pour applications avec de l'air comprimé — Spécifications,2006-06-23,3,['23.040.70'],ISO/TC 45/SC 1,9599,[11906],[68044],"['en','fr']",13,"<p>ISO 5774:2006 specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from -10 °C to +60 °C.</p><p>The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and 4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at 60 °C

68044,IS,,ISO 5774:2016,Plastics hoses — Textile-reinforced types for compressed-air applications — Specification,Tuyaux en plastique — Types armés de textile pour applications avec de l'air comprimé — Spécifications,2016-01-15,4,['23.040.70'],ISO/TC 45/SC 1,9599,[41420],[84063],"['en','fr']",13,"<p>ISO 5774:2016 specifies the requirements for four types of flexible thermoplastic hose, textile reinforced, for compressed-air applications in the temperature range from −10 °C to +60 °C.</p><p>The four types are classified as light service for a maximum working pressure of 7 bar at 23 °C and 4,5 bar at 60 °C, medium service for a maximum working pressure of 10 bar at 23 °C and 6,5 bar at 60 °C

11907,IS,,ISO 5775-1:1980,Bicycle tyres and rims — Part 1: Tyre designations and dimensions,Pneumatiques et jantes pour cycles — Partie 1: Désignation et dimensions des pneumatiques,1980-10-01,2,['83.160.10'],ISO/TC 31/SC 10,9599,,[11908],"['en','fr']",8,

11909,IS,Add,ISO 5775-1:1980/Add 1:1982,Bicycle tyres and rims — Part 1: Tyre designations and dimensions — Addendum 1,Pneumatiques et jantes pour cycles — Partie 1: Désignation et dimensions des pneumatiques — Additif 1,1982-12-01,2,['83.160.10'],ISO/TC 31/SC 10,9599,,[11908],['en'],2,

11908,IS,,ISO 5775-1:1988,Bicycle tyres and rims — Part 1: Tyre designations and dimensions,Pneumatiques et jantes pour cycles — Partie 1: Désignation et cotes des pneumatiques,1988-11-17,3,['83.160.10'],ISO/TC 31/SC 10,9599,"[11907,11909]",[21344],"['en','fr']",8,

21344,IS,,ISO 5775-1:1994,Bicycle tyres and rims — Part 1: Tyre designations and dimensions,Pneumatiques et jantes pour cycles — Partie 1: Désignation et cotes des pneumatiques,1994-10-27,4,['83.160.10'],ISO/TC 31/SC 10,9599,[11908],[25326],"['en','fr']",11,

25326,IS,,ISO 5775-1:1997,Bicycle tyres and rims — Part 1: Tyre designations and dimensions,Pneumatiques et jantes pour cycles — Partie 1: Désignation et cotes des pneumatiques,1997-11-27,5,['83.160.10'],ISO/TC 31/SC 10,9599,[21344],[56559],"['en','fr']",11,

56559,IS,,ISO 5775-1:2014,Bicycle tyres and rims — Part 1: Tyre designations and dimensions,Pneumatiques et jantes pour cycles — Partie 1: Désignation et cotes des pneumatiques,2014-08-27,6,['83.160.10'],ISO/TC 31/SC 10,9599,[25326],[80740],"['en','fr']",19,<p>ISO 5755-1:2014 specifies the designations and dimensions for the following pneumatic bicycle tyres:</p><p>-'wired edge' tyres mounted on straight side or crotchet type rims;</p><p>-'beaded edge' tyres mounted on hooked bead rims.</p><p>Tubular sew-up tyres and non-pneumatic tyres are not covered by ISO 5775-1:2014.</p>

11910,IS,,ISO 5775-2:1989,Bicycle tyres and rims — Part 2: Rims,Pneumatiques et jantes pour cycles — Partie 2: Jantes,1989-06-29,1,['43.150'],ISO/TC 31/SC 10,9599,,[11912],"['en','fr']",12,