Withdrawn and superseded ISO standards — page 129 of 246

30192,IS,,ISO 5167-4:2003,Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 4: Venturi tubes,Mesure de débit des fluides au moyen d'appareils déprimogènes insérés dans des conduites en charge de section circulaire — Partie 4: Tubes de Venturi,2003-02-24,1,['17.120.10'],ISO/TC 30/SC 2,9599,,[79181],"['en','fr']",24,"<p>ISO 5167-4:2003 specifies the geometry and method of use (installation and operating conditions) of Venturi tubes when they are inserted in a conduit running full to determine the flowrate of the fluid flowing in the conduit. </p><p>ISO 5167-4:2003 also provides background information for calculat

62568,IS,,ISO 5167-5:2016,Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 5: Cone meters,Mesure de débit des fluides au moyen d'appareils déprimogènes insérés dans des conduites en charge de section circulaire — Partie 5: Cônes de mesure,2016-03-07,1,['17.120.10'],ISO/TC 30/SC 2,9599,,[83688],"['en','fr']",15,"<p>ISO 5167-5:2016 specifies the geometry and method of use (installation and operating conditions) of cone meters when they are inserted in a conduit running full to determine the flow rate of the fluid flowing in the conduit.</p><p>As the uncertainty of an uncalibrated cone meter might be too high for

68502,IS,,ISO 5167-6:2019,Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 6: Wedge meters,Mesure de débit des fluides au moyen d'appareils déprimogènes insérés dans des conduites en charge de section circulaire — Partie 6: Débitmètres à coin,2019-02-04,1,['17.120.10'],ISO/TC 30/SC 2,9599,,[83689],"['en','fr']",13,"<p>This document specifies the geometry and method of use (installation and operating conditions) of wedge meters when they are inserted in a conduit running full to determine the flow rate of the fluid flowing in the conduit.</p><p>NOTE 1 As the uncertainty of an uncalibrated wedge meter can be

11171,IS,,ISO 5168:1978,Measurement of fluid flow — Estimation of uncertainty of a flow-rate measurement,Mesure de débit des fluides — Calcul de l'erreur limite sur une mesure de débit,1978-07-01,1,['17.120.10'],ISO/TC 30,9599,,[11172],"['en','fr']",26,

4579,IS,,ISO 517:1996,Photography — Apertures and related properties pertaining to photographic lenses — Designations and measurements,Photographie — Ouvertures et grandeurs associées relatives aux objectifs photographiques — Désignations et mesurages,1996-12-26,2,['37.040.10'],ISO/TC 172/SC 1,9599,,[50089],['en'],8,"<p>Pertains to apertures and related properties of photographic lenses affecting the illuminance at the centre of the image. Does apply only to lenses focused on objects at infinity; that is, at least 50 times the focal length of the lens.</p>"

44794,IS,Cor,ISO 517:1996/Cor 1:2006,Photography — Apertures and related properties pertaining to photographic lenses — Designations and measurements — Technical Corrigendum 1,Photographie — Ouvertures et grandeurs associées relatives aux objectifs photographiques — Désignations et mesurages — Rectificatif technique 1,2006-10-10,2,['37.040.10'],ISO/TC 172/SC 1,9599,,[50089],['en'],1,

11175,IS,,ISO 5171:1980,"Pressure gauges used in welding, cutting and related processes","Manomètres utilisés pour le soudage, le coupage et les techniques connexes",1980-07-01,1,['25.160.30'],ISO/TC 44,9599,,[11176],"['en','fr']",7,

11176,IS,,ISO 5171:1995,"Pressure gauges used in welding, cutting and allied processes","Manomètres utilisés pour le soudage, le coupage et les techniques connexes",1995-07-06,2,['25.160.30'],ISO/TC 44/SC 8,9599,[11175],[44987],"['en','fr']",9,"<p>Specifies requirements for Bourdon-tube pressure gauges used with compressed gases at pressures up to 300 bar (30 MPa) in welding, cutting and allied processes. It also applies for the use of dissolved acetylen and for liquefied gases under pressure. Cancels and replaces the former edition, which has been technically revised.</p>"

44987,IS,,ISO 5171:2009,"Gas welding equipment — Pressure gauges used in welding, cutting and allied processes","Matériel de soudage au gaz — Manomètres utilisés pour le soudage, le coupage et les techniques connexes",2009-05-15,3,['25.160.30'],ISO/TC 44/SC 8,9599,[11176],[69236],"['en','fr','ru']",13,"<p>ISO 5171:2009 specifies requirements for Bourdon-tube pressure gauges normally used with compressed gas systems at pressures up to 30 MPa (300 bar) in welding, cutting and allied processes. It also covers use for dissolved acetylene and for liquefied gases under pressure. It does not cover gauges for acetylene in acetylene-manufacturing plants.</p>"

11178,IS,,ISO 5172:1977,Manual blowpipes for welding and cutting,Chalumeaux manuels pour soudage et coupage,1977-12-01,1,['25.160.30'],ISO/TC 44,9599,,[11179],"['en','fr']",11,

11179,IS,,ISO 5172:1995,"Manual blowpipes for welding, cutting and heating — Specifications and tests","Chalumeaux manuels pour soudage aux gaz, coupage et chauffage — Spécifications et essais",1995-04-27,2,['25.160.30'],ISO/TC 44/SC 8,9599,[11178],[36106],"['en','fr']",26,"<p>Cancels and replaces the first edition (1977). Specifies the characteristics of manual blowpipes for gas welding, cutting and heating of metals and gives specifications and corresponding test. Covers manual blowpipes for welding and heating up to 1 800 l/h to 2 500 l/h fuel gas and cutting blowpipes for cutting structural steel up to a thickness of 300 mm. Does not apply to air aspirated blowpipes.</p>"

24655,IS,Amd,ISO 5172:1995/Amd 1:1995,"Manual blowpipes for welding, cutting and heating — Specifications and tests — Amendment 1","Chalumeaux manuels pour soudage aux gaz, coupage et chauffage — Spécifications et essais — Amendement 1",1995-11-09,2,['25.160.30'],ISO/TC 44/SC 8,9599,,[36106],"['en','fr']",3,<p>Amendments applies to clauses 8.2.5 and 8.2.6 only.</p>

11180,IS,,ISO 5173:1981,Fusion welded butt joints in steel — Transverse root and face bend test,"Joints soudés bout à bout par fusion dans l'acier — Essais de pliage transversaux, à l'endroit et à l'envers",1981-10-01,1,['25.160.40'],ISO/TC 44,9599,,[33810],"['en','fr']",4,

33810,IS,,ISO 5173:2000,Destructive tests on welds in metallic materials — Bend tests,Essais destructifs des soudures sur matériaux métalliques — Essais de pliage,2000-12-21,2,['25.160.40'],ISO/TC 44/SC 5,9599,"[11180,11183]",[44748],"['en','fr']",22,

44748,IS,,ISO 5173:2009,Destructive tests on welds in metallic materials — Bend tests,Essais destructifs des soudures sur matériaux métalliques — Essais de pliage,2009-06-11,3,['25.160.40'],ISO/TC 44/SC 5,9599,[33810],"[69608,81724]","['en','fr','ru']",18,"<p>ISO 5173:2009 specifies a method for making transverse root, face and side bend tests on test specimens taken from butt welds, butt welds with cladding (subdivided into welds in clad plates and clad welds) and cladding without butt welds, in order to assess ductility and/or absence of imperfections on or near the surface of the test specimen. It also gives the dimensions of the test specimen.</p><p>In addition ISO 5173:2009 specifies a

59428,IS,Amd,ISO 5173:2009/Amd 1:2011,Destructive tests on welds in metallic materials — Bend tests — Amendment 1,Essais destructifs des soudures sur matériaux métalliques — Essais de pliage — Amendement 1,2011-10-25,3,['25.160.40'],ISO/TC 44/SC 5,9599,,"[69608,81724]","['en','fr']",1,

11182,IS,,ISO 5175-1:1983,Gas welding and cutting equipment and allied processes — Safety devices for fuel gases and oxygen or compressed air — Part 1: General specifications and requirements,"Équipement de soudage aux gaz, de coupage et procédés connexes — Dispositifs de sécurité pour les gaz combustibles et l'oxygène ou l'air comprimé — Partie 1: Spécifications et exigences générales",1983-12-01,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[11181],"['en','fr']",5,

11181,IS,,ISO 5175:1987,"Equipment used in gas welding, cutting and allied processes — Safety devices for fuel gases and oxygen or compressed air — General specifications, requirements and tests","Équipements de soudage aux gaz, de coupage et procédés connexes — Dispositifs de sécurité pour les gaz combustibles et l'oxygène ou l'air comprimé — Spécifications et exigences générales et essais",1987-09-24,1,['25.160.30'],ISO/TC 44/SC 8,9599,[11182],"[39100,68301,68299]","['en','fr']",8,"<p>Refers to safety devices used downstream of cylinder or pipeline outlet regulators and of pipeline outlet valves, and upstream of blowpipes. Does not specify location and combination of these devices in the g

60319,IS,Amd,ISO 5175:1987/Amd 1:2015,"Equipment used in gas welding, cutting and allied processes — Safety devices for fuel gases and oxygen or compressed air — General specifications, requirements and tests — Amendment 1","Équipements de soudage aux gaz, de coupage et procédés connexes — Dispositifs de sécurité pour les gaz combustibles et l'oxygène ou l'air comprimé — Spécifications et exigences générales et essais — Amendement 1",2015-02-13,1,['25.160.30'],ISO/TC 44/SC 8,9599,,"[68301,68299]","['en','fr']",1,

11183,IS,,ISO 5177:1981,Fusion welded butt joints in steel — Transverse side bend test,Joints soudés bout à bout par fusion dans l'acier — Essais de pliages transversaux latéraux,1981-08-01,1,['25.160.40'],ISO/TC 44,9599,,[33810],"['en','fr']",4,

32829,IS,,ISO 5178:2001,Destructive tests on welds in metallic materials — Longitudinal tensile test on weld metal in fusion welded joints,Essais destructifs des soudures sur matériaux métalliques — Essai de traction longitudinale du métal fondu des assemblages soudés par fusion,2001-02-01,1,['25.160.40'],ISO/TC 44/SC 5,9599,,[75738],"['en','fr']",6,

11185,IS,,ISO 5179:1983,Investigation of brazeability using a varying gap test piece,Étude de l'aptitude au brasage au moyen d'une éprouvette à jeu variable,1983-10-01,1,['25.160.50'],ISO/TC 44/SC 13,9599,,[78012],"['en','fr']",5,<p>Specifies a testing method for assessing the influence of the various parameters which can influence brazing during manufacture as a function of clearances. The test piece described gives guidance about the effects of brazing variables on filler metal flow when capillary gaps of different dimensions are used.</p>

4580,IS,,ISO 518:1977,"Photography — Camera accessory shoes, with and without electrical contacts, for photoflash lamps and electronic photoflash units","Photographie — Griffes pour accessoires d'appareils de prises de vue, avec et sans contact électrique pour lampes à éclairs et équipements électroniques à éclairs",1977-08-01,1,['37.040.10'],ISO/TC 42,9599,,[36330],"['en','fr']",2,"<p>The dimensions given are basic for the solid shoe. They may be changed when the shoe is equipped with springs or other means for holding the accessory foot tightly or maintaining good electrical contact, provided interchangeability and functions are not affected.</p>"

11187,IS,,ISO 5182:1978,Materials for resistance welding electrodes and ancillary equipment,Matériaux pour électrodes de soudage par résistance et equipements annexes,1978-11-01,1,['25.160.20'],ISO/TC 44,9599,,[11188],"['en','fr']",6,

11188,IS,,ISO 5182:1991,Welding — Materials for resistance welding electrodes and ancillary equipment,Soudage — Matériaux pour électrodes de soudage par résistance et équipements annexes,1991-03-28,2,['25.160.20'],ISO/TC 44/SC 6,9599,[11187],[38571],"['en','fr']",9,"<p>This second edition cancels and replaces the first edition (ISO 5182:1978). Specifies the characteristics of the materials which are used for carrying current and transmitting force to the work. Gives normative references. Defines the term softening temperature. Classifies copper and copper alloys and sintered materials. Specifies test methods, designation, typical applications (annex A), hardness conversions (annex B). Annexe

38571,IS,,ISO 5182:2008,Resistance welding — Materials for electrodes and ancillary equipment,Soudage par résistance — Matériaux pour électrodes et équipements annexes,2008-01-15,3,['25.160.20'],ISO/TC 44/SC 6,9599,[11188],[67356],"['en','fr','ru']",10,<p>ISO 5182:2008 specifies the characteristics of materials for resistance welding electrodes and ancillary equipment which are used for carrying current and transmitting force to the work.</p>

11190,IS,,ISO 5183-1:1988,"Resistance spot welding — Electrode adaptors, male taper 1:10 — Part 1: Conical fixing, taper 1:10",Soudage par points par résistance — Allonges d'électrode à embout amovible (cône mâle 1:10) — Partie 1: Emmanchement conique 1:10,1988-11-24,1,['25.160.30'],ISO/TC 44/SC 6,9599,[11189],[27202],"['en','fr']",2,

11189,IS,,ISO 5183:1979,Resistance spot welding electrode adaptors,Corps de pointes d'électrode à embout amovible,1979-07-01,1,['25.160.20'],ISO/TC 44,9599,,"[11191,11190]","['en','fr']",2,

11191,IS,,ISO 5183-2:1988,"Resistance spot welding — Electrode adaptors, male taper 1:10 — Part 2: Parallel shank fixing for end-thrust electrodes",Soudage par points par résistance — Allonges d'électrode à embout amovible (cône mâle 1:10) — Partie 2: Emmanchement cylindrique pour poussée en bout,1988-11-24,1,['25.160.30'],ISO/TC 44/SC 6,9599,[11189],[34487],"['en','fr']",3,

11194,IS,,ISO 5186:1995,Oxygen/fuel gas blowpipes (cutting machine type) with cylindrical barrels — General specifications and test methods,Chalumeaux oxy-gaz combustible (type machine d'oxycoupage) à corps cylindrique — Spécifications générales et méthodes d'essai,1995-05-11,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[36106],"['en','fr']",16,"<p>Gives the characteristics of machine cutting blowpipes and the specifications and corresponding test. Applies to machine cutting blowpipes which are fitted to a gas cutting machine and which have cylindrical barrels where the nozzle centre is coaxial with the barrel, the blowpipe operates with oxygen and fuel gas and has a cutting range from 3 mm to 300 m

4581,IS,,ISO 519:1974,Photography — Small flash connections for hand-held cameras — Dimensions,Photographie — Petits raccords de lampe à éclairs pour les appareils de prise de vue portatifs — Dimensions,1974-05-01,1,['37.040.10'],ISO/TC 42,9599,,[4582],"['en','fr']",1,

11197,IS,,ISO 5191:1980,Wrought aluminium and aluminium alloy products — General conditions for inspection and delivery,Produits en aluminium et alliages d'aluminium corroyés — Conditions générales de contrôle et de livraison,1980-04-01,1,['77.150.10'],ISO/TC 79/SC 6,9599,,"[12690,12681,12696,12675]","['en','fr']",3,

11198,IS,,ISO 5193:1981,Wrought aluminium and aluminium alloys — Drawn round bars — Tolerances on shape and dimensions (Symmetric plus and minus tolerances on diameter),Aluminium et alliages d'aluminium corroyés — Barres rondes étirées — Tolérances sur forme et dimensions (Tolérances de diamètre symétriques en plus et en moins),1981-09-01,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[54489],"['en','fr']",1,"<p>The tolerances apply to drawn round bars having diameters in the range from 1 to 65 mm inclusive. Tolerances on diameter are given in table 1, tolerances on fixed lengths are given in table 2. Moreover, circularity and straightness are specified.</p>"

11204,IS,,ISO 5199:1986,Technical specifications for centrifugal pumps — Class II,Spécifications techniques pour pompes centrifuges — Classe II,1986-04-17,1,['23.080'],ISO/TC 115/SC 1,9599,,"[11205,31945]","['en','fr']",37,"<p>Covers class II requirements for pumps of back pull-out construction as used primarily in the chemical and petrochemical industries. Includes design features concerned with installation, maintenance and safety for these pumps, including baseplate couplings and auxiliary piping but excluding the driver.</p>"

4583,IS,,ISO 520:1977,Cereals and pulses — Determination of the mass of 1000 grains,Céréales et légumineuses — Détermination de la masse de 1000 grains,1977-11-01,1,['67.060'],ISO/TC 34/SC 4,9599,,[52270],"['en','fr']",2,"<p>The method specified in ISO 520:1977 is applicable to all cereals and pulses with the exception of seed lots for sowing purposes. It consists in weighing a quantity of the sample, separation of the whole grains and weighing the residue, followed by counting of the whole grains. Then dividing of the mass of the whole grains by their number, and expression of the result in relation to 1 000 grains.</p>"

11207,IS,,ISO 5208:1982,Industrial valves — Pressure testing for valves,Robinetterie industrielle — Essais sous pression pour les appareils de robinetterie,1982-09-01,1,['23.060.01'],ISO/TC 153,9599,,[11208],"['en','fr']",2,

11208,IS,,ISO 5208:1993,Industrial valves — Pressure testing of valves,Robinetterie industrielle — Essais sous pression pour les appareils de robinetterie,1993-01-21,2,['23.060.01'],ISO/TC 153,9599,[11207],"[39474,43239]","['en','fr']",3,"<p>Specifies tests to confirm the pressure-containing capability of the shell of an industrial valve under pressure, and to verify the tightness and pressure-retaining adequacy of the valve seat and closure mechanism.</p>"

43239,IS,,ISO 5208:2008,Industrial valves — Pressure testing of metallic valves,Robinetterie industrielle — Essais sous pression des appareils de robinetterie métalliques,2008-07-30,3,['23.060.01'],ISO/TC 153,9599,[11208],"[54464,65111]","['en','fr']",13,"<p>ISO 5208:2008 specifies examinations and tests that a valve manufacturer needs to act upon in order to establish the integrity of the pressure boundary of an industrial metallic valve and to verify the degree of valve closure tightness and the structural adequacy of its closure mechanism.</p><p>ISO 5208:2008 is to be applied in conjunction with the specific requirements of a valve product standard to the extent cited by the product stand

11209,IS,,ISO 5209:1977,General purpose industrial valves — Marking,Appareils de robinetterie industrielle d'usage général — Marquage,1977-08-01,1,['23.060.01'],ISO/TC 153,9599,,"[76075,38586]","['en','fr']",2,"<p>Specifies mandatory and optional markings of general purpose valves and states the manner of applying the markings, i.e. on the body, on a flange, or on a identification plate. Markings on the body may be integral with the body or on a plate securely fixed to the body. The table lists those items which may be included in international standards for individual types of valves.</p>"

4584,IS,,ISO 521:1975,Machine chucking reamers with parallel shanks or Morse taper shanks,"Alésoirs à machine, à queue cylindrique et à queue cône Morse",1975-09-01,1,['25.100.30'],ISO/TC 29/SC 9,9599,,[51322],"['en','fr']",5,"<p>Lays down only metric dimensions. For each type of reamer mentioned above ISO 521 gives two tables, one showing preferred sizes with corresponding dimensions and the other, a general table set out as functions of diameter steps. Provision is also made for tolerances on length, cutting diameters and the diameters of parallel shank.</p>"

11212,IS,,ISO 5210-1:1977,Multi-turn valve actuator attachment — Part 1: Flange dimensions,Raccordement des servomoteurs multitours aux appareils de robinetterie — Partie 1: Dimensions des embases,1977-12-01,1,['23.060.01'],ISO/TC 153,9599,,[11211],['en'],2,

11211,IS,,ISO 5210:1991,Industrial valves — Multi-turn valve actuator attachments,Robinetterie industrielle — Raccordement des actionneurs multitours aux appareils de robinetterie,1991-10-03,1,['23.060.01'],ISO/TC 153,9599,"[11213,11214,11212]",[52534],"['en','fr']",8,"<p>Specifies flange dimensions, driving component dimensions, and reference values for torque and thrust for flanges. This first edition cancels and replaces ISO 5210-1:1977, ISO 5210-2:1979 and ISO 5210-3:1982. Annex A is for information only.</p>"

11213,IS,,ISO 5210-2:1979,Multi-turn valve actuator attachment — Part 2: Flange and coupling performance characteristics,Raccordement des servomoteurs multitours aux appareils de robinetterie — Partie 2: Caractéristiques d'utilisation de l'embase et de l'accouplement,1979-12-01,1,['23.060.01'],ISO/TC 153,9599,,[11211],['en'],1,

52534,IS,,ISO 5210:2017,Industrial valves — Multi-turn valve actuator attachments,Robinetterie industrielle — Raccordement des actionneurs multitours aux appareils de robinetterie,2017-03-29,2,['23.060.01'],ISO/TC 153,9599,[11211],[86752],"['en','fr']",15,"<p>ISO 5210:2017 specifies the requirements for the attachment of multi-turn actuators to valves.</p><p>Throughout this document, 'actuator' may be understood as 'actuator and/or gearbox' providing a multi-turn and/or linear output.</p><p>ISO 5210:2017 specifies:</p><p>- flange dimensions necessary for the attachment of actuators to industrial valves [see Figure 1 a)] or to intermediate supports [see Figure 1 b)];</p><p>- those

86752,IS,,ISO 5210:2023,Industrial valves — Multi-turn valve actuator attachments,Robinetterie industrielle — Raccordement des actionneurs multitours aux appareils de robinetterie,2023-09-22,3,['23.060.01'],ISO/TC 153,9599,"[52534,84364]",[89905],"['en','fr']",19,"<p class='MsoBodyText'><span lang='EN-GB'>This document specifies the requirements for the attachment of multi-turn actuators to valves.</span></p><p class='MsoBodyText'><span lang='EN-GB'>Throughout this document, “actuator” can be understood as “actuator and/or gearbox” providing a multi-turn and/or linear output.</span></p><p class='MsoBodyText'><span lang='EN-GB'>It specifies:</span></p><p class='ListContinue1' style='mso-list:

11214,IS,,ISO 5210-3:1982,Multi-turn valve actuator attachment — Part 3: Dimensions of driving components,Raccordement des servomoteurs multitours aux appareils de robinetterie — Partie 3: Dimensions des éléments d'entraînement,1982-06-01,1,['23.060.01'],ISO/TC 153,9599,,[11211],['en'],4,

11216,IS,,ISO 5211-1:1977,Part-turn valve actuator attachment — Part 1: Flange dimensions,Raccordement des servomoteurs à fraction de tour aux appareils de robinetterie — Partie 1: Dimensions des embases,1977-12-01,1,['23.060.01'],ISO/TC 153,9599,,[11215],"['en','fr']",2,

11217,IS,,ISO 5211-2:1979,Part-turn valve actuator attachment — Part 2: Flange and coupling performance characteristics,Raccordement des servomoteurs à fraction de tour aux appareils de robinetterie — Partie 2: Caractéristiques d'utilisation de l'embase et de l'accouplement,1979-12-01,1,['23.060.01'],ISO/TC 153,9599,,[11215],"['en','fr']",1,

11215,IS,,ISO 5211:2001,Industrial valves — Part-turn actuator attachments,Robinetterie industrielle — Raccordement des actionneurs à fraction de tour,2001-02-22,1,['23.060.01'],ISO/TC 153,9599,"[11217,11218,11216]","[62594,35931]","['en','fr']",14,

62594,IS,,ISO 5211:2017,Industrial valves — Part-turn actuator attachments,Robinetterie industrielle — Raccordement des actionneurs à fraction de tour,2017-03-28,2,['23.060.01'],ISO/TC 153,9599,[11215],[86753],"['en','fr']",24,"<p>ISO 5211:2017 specifies requirements for the attachment of part-turn actuators, with or without gearboxes, to industrial valves.</p><p>The attachment of part-turn actuators to control valves in accordance with the requirements of this document is subject to an agreement between the supplier and the purchaser.</p><p>ISO 5211:2017 specifies:</p><p>- flange dimensions necessary for the attachment of part-turn actuators to industrial valves [see Figures 1 a) and 1

86753,IS,,ISO 5211:2023,Industrial valves — Part-turn actuator attachments,Robinetterie industrielle — Raccordement des actionneurs à fraction de tour,2023-09-12,3,['23.060.01'],ISO/TC 153,9599,"[84365,62594]",[89904],"['en','fr']",28,"<p class='MsoBodyText'><span lang='EN-GB'>This document specifies requirements for the attachment of part-turn actuators, with or without gearboxes, to industrial valves.</span></p><p class='MsoBodyText'><span lang='EN-GB'>The attachment of part-turn actuators to control valves in accordance with the requirements of this document is subject to an agreement between the supplier and the purchaser.</span></p><p class='MsoBodyText'><span lang='EN-GB'>This document

11218,IS,,ISO 5211-3:1982,Part-turn valve actuator attachment — Part 3: Dimensions of driving components,Raccordement des servomoteurs à fraction de tour aux appareils de robinetterie — Partie 3: Dimensions des éléments d'entraînement,1982-06-01,1,['23.060.01'],ISO/TC 153,9599,,[11215],"['en','fr']",3,

11219,IS,,ISO 5218:1977,Information interchange — Representation of human sexes,Échange d'information — Représentation des sexes humains,1977-09-01,1,['35.040.50'],ISO/IEC JTC 1/SC 32,9599,,"[31365,36266]","['en','fr']",1,<p>A uniform representation of human sexes for information interchange is defined. Is intended to - reduce time for recording and formatting representation of sexes and transmit them; improve clarity and accuracy of interchange; minimize amoung of human intervention for communicating the representation of sexes; reduce costs. Meets requirements of most applications needing to code human sexes. Provides numeric code independent of language-devired codes.</p>

81013,IS,,ISO 5222-1:2023,Heat recovery ventilators and energy recovery ventilators — Testing and calculating methods for seasonal performance factor — Part 1: Sensible heating recovery seasonal performance factors of heat recovery ventilators (HRV),Ventilateurs récupérateurs de chaleur et ventilateurs récupérateurs d'énergie — Méthodes d'essai et de calcul des facteurs de performances saisonnières — Partie 1: Facteurs de performances saisonnières de la récupération de chaleur sensible des ventilateurs récupérateurs de chaleur (HRV),2023-08-29,1,['23.120'],ISO/TC 86/SC 6,9599,,[89406],['en'],22,"<p class='MsoBodyText'><span lang='EN-GB'>This document specifies the testing and calculating met

11224,IS,,ISO 5223:1983,Test sieves for cereals,Tamis de contrôle pour céréales,1983-05-01,2,['67.260'],ISO/TC 34/SC 4,9599,,[11225],"['en','fr']",3,

11231,IS,,ISO 5232:1988,Graphical symbols for textile machinery,Symboles graphiques pour machines textiles,1988-12-29,1,"['59.120.01','01.080.30','01.080.20']",ISO/TC 72/SC 4,9599,[11230],[26571],"['en','fr']",42,

11233,IS,,ISO 5234:1980,Textile machinery and accessories — Metallic card clothing — Terms and definitions,Matériel pour l'industrie textile — Garnitures de carde — Termes et définitions,1980-07-01,1,"['01.040.59','59.120.10']",ISO/TC 72/SC 1,9599,,[38584],"['en','fr','ru']",20,"<p>Shows saw-tooth wire for metallic card clothing with various cross-sections and tooth forms. Terms are defined. (3 figures, 1 table, 1 annex).</p>"

11235,IS,,ISO 5237:1978,Textile machinery and accessories — Cones for yarn winding (cross wound) — Half angle of the cone 5 degrees 57',Matériel pour l'industrie textile — Cônes pour bobinage croisé — Demi-angle du cône 5 degrés 57',1978-08-01,1,['59.120.20'],ISO/TC 72/SC 1,9599,,[21964],"['en','fr']",2,

11239,IS,,ISO 5240:1978,Textile machinery and accessories — Warp creels — Terminology and main dimensions,Matériel pour l'industrie textile — Cantres d'ourdissage — Terminologie et dimensions principales,1978-07-01,1,['59.120.20'],ISO/TC 72,9599,,[21948],"['en','fr']",2,

11240,IS,,ISO 5241:1978,Textile machinery and accessories — Weaver's beams — Terminology and main dimensions,Matériel pour l'industrie textile — Ensouples de tissage — Terminologie et dimensions de base,1978-10-01,1,"['59.120.30','01.040.59']",ISO/TC 72,9599,,[15169],"['en','fr']",3,

11241,IS,,ISO 5243:1977,Textile machinery and accessories — Numbering of heald frames in a loom,Matériel pour l'industrie textile — Numérotage des cadres de lisses dans un métier à tisser,1977-04-01,1,['59.120.30'],ISO/TC 72/SC 3,9599,,[36883],"['en','fr']",1,<p>Specifies the principle of numbering heald frames in a loom and describes it by means of a figure. The numbering of the heald frames is made from the cloth delivery side of a loom (see the figure).</p>

11244,IS,,ISO 5247:1983,Textile machinery and accessories — Weaving machines — Classification and vocabulary,Matériel pour l'industrie textile — Métiers et machines à tisser — Classification et vocabulaire,1983-05-01,1,"['59.120.30','01.040.59']",ISO/TC 72/SC 3,9599,,[36882],"['en','fr','ru']",14,"<p>Establishes a classification and list of equivalent terms in the three official ISO languages (English, French and Russian) for weaving machines used in the textile industry for the production of woven fabrics. Gives in an annex the equivalent terms in German.</p>"

11247,IS,,ISO 5248:1982,Textile machinery and accessories — Dyeing and finishing machinery — Vocabulary for ancillary devices,Matériel pour l'industrie textile — Machines de teinture et d'apprêt — Vocabulaire relatif aux dispositifs annexes,1982-12-01,1,"['01.040.59','59.120.50']",ISO/TC 72/SC 4,9599,,[35407],"['en','fr','ru']",20,"<p>Gives an illustrated nomenclature for the most common ancillary devices placed before, between and after dyeing and finishing machines. The terms used are placed under the following headings: Basic terms (in general), Feeding of material, Guiding of material, Control of the speed of material, Accumulation of material, Treatment of material, Delivery of material

4588,IS,,ISO 525:1975,"Bonded abrasive products — General features — Designation, ranges of dimensions, and profiles","Produits abrasifs agglomérés — Généralités — Désignation, gammes de dimensions, et profils",1975-02-01,1,['25.100.70'],ISO/TC 29,9599,,[4589],"['en','fr']",5,

4589,IS,,ISO 525:1986,"Bonded abrasive products — General — Designation, marking, range of outside diameters and tolerances","Produits abrasifs agglomérés — Généralités — Désignation, marquage, gamme des diamètres extérieurs et tolérances",1986-11-27,2,['25.100.70'],ISO/TC 29/SC 5,9599,[4588],[21894],"['en','fr']",13,

21894,IS,,ISO 525:1999,Bonded abrasive products — General requirements,Produits abrasifs agglomérés — Exigences générales,1999-09-30,3,['25.100.70'],ISO/TC 29/SC 5,9599,[4589],[40211],"['en','fr']",19,

40211,IS,,ISO 525:2013,Bonded abrasive products — General requirements,Produits abrasifs agglomérés — Exigences générales,2013-03-19,4,['25.100.70'],ISO/TC 29/SC 5,9599,[21894],[78476],"['en','fr']",13,"<p>ISO 525:2013 is applicable to bonded abrasive products (e.g. grinding wheels, segments, sticks and stones) in general, excluding superabrasive products and coated abrasive products.</p><p>ISO 525:2013 specifies: </p><ul><li>the ISO type number and shape;</li><li>dimensional symbols;</li><li>standard profiles;</li><li>requirements for dimensions, limit deviations and tolerances as well as permissible unbalance;</li><li>the specification mark; </li><li>the marking requirements.</li></ul>" 40

11249,IS,,ISO 5250:1982,Textile machinery and accessories — Dyeing and finishing machinery — Vocabulary for stenters,Matériel pour l'industrie textile — Machines de teinture et d'apprêt — Vocabulaire relatif aux rames,1982-12-01,1,"['01.040.59','59.120.50']",ISO/TC 72/SC 4,9599,,[35408],"['en','fr','ru']",23,"<p>Gives an illustrated nomenclature of machines known as stenters, used in the textile finishing industry (bleaching, dyeing, printing and finishing), for the thermal treatment of fabric with maintainance of the width and adjustment of latter, if necessary. The terms used are placed under the following headings: Types of stenter; Machine features; Designation of side and indication of

11251,IS,,ISO 5252:1977,Steel tubes — Tolerance systems,Tubes en acier — Systèmes de tolérances,1977-11-01,1,['23.040.10'],ISO/TC 5,9599,,[11252],"['en','fr']",3,

11253,IS,,ISO 5256:1985,Steel pipes and fittings for buried or submerged pipe lines — External and internal coating by bitumen or coal tar derived materials,Tubes et accessoires en acier utilisés pour canalisations enterrées ou immergées — Revêtements externe et interne au moyen de matériaux hydrocarbonés,1985-10-31,1,"['23.040.10','23.040.40']",ISO/TC 5/SC 1,9599,,[22274],"['en','fr']",54,"<p>Specifies the coatings suitable for protecting surfaces of steel pipes and fittings, either individually or after assembly, and also the conditions for the application of such protective coatings. Applies to welded and seamless pipes of non-alloy steels used for the conveyance of fluids. The coatings o

11255,IS,,ISO 5261:1981,Technical drawings for structural metal work,Dessins techniques pour constructions métalliques,1981-08-01,1,['01.100.30'],ISO/TC 10/SC 6,9599,,"[21512,12039]","['en','fr']",10,

11256,IS,,ISO 5263:1979,Pulps — Laboratory wet disintegration,Pâtes — Désintégration humide de laboratoire,1979-05-01,1,['85.040'],ISO/TC 6,9599,,[11257],"['en','fr']",5,

11257,IS,,ISO 5263:1995,Pulps — Laboratory wet disintegration,Pâtes — Désintégration humide en laboratoire,1995-06-08,2,['85.040'],ISO/TC 6,9599,[11256],"[37894,37895,34644,37893]","['en','fr']",5,"<p>Cancels and replaces the first edition (1979). Specifies an apparatus and a method for the laboratory wet disintegration of pulp. Specifies the disintegration apparatus and in some cases the disintegration procedures required in a number of other International Standards dealing with pulps. The method is applicable to most kinds of pulp, including recycled fibres, it is not suitable for some very long-fibred pulps such as those from cotton and similar materials.</p>"

37895,IS,,ISO 5263-3:2004,Pulps — Laboratory wet disintegration — Part 3: Disintegration of mechanical pulps at > 85 degrees C,Pâtes — Désintégration humide en laboratoire — Partie 3: Désintégration des pâtes mécaniques à une température supérieure ou égale à 85 degrés C,2004-09-07,1,['85.040'],ISO/TC 6,9599,[11257],[80256],['en'],11,"<p>ISO 5263-3:2004 specifies an apparatus and the procedures for the laboratory wet disintegration of mechanical pulps that exhibit latency. This apparatus and procedure are required for preparation of the test portion in a number of other International Standards dealing with pulps.</p><p>ISO 5263-3:2004 is applicable to all kind of mechanical pulps (i.e. mecha

11259,IS,,ISO 5264-2:1979,Pulps — Laboratory beating — Part 2: PFI mill method,Pâtes — Raffinage de laboratoire — Partie 2: Méthode au moulin PFI,1979-08-01,1,['85.040'],ISO/TC 6,9599,,[33988],"['en','fr']",4,"<p>Is limited to the furnishing and beating of the stock, the with-drawal and distribution of the samples, and the beating equipment. The beating is a preliminary step in testing the physical properties of the pulp.</p>"

33988,IS,,ISO 5264-2:2002,Pulps — Laboratory beating — Part 2: PFI mill method,Pâtes — Raffinage de laboratoire — Partie 2: Méthode au moulin PFI,2002-11-18,2,['85.040'],ISO/TC 6,9599,[11259],[53432],"['en','fr']",10,"<p>ISO 5264-2:2002 specifies a method, using a PFI mill, for the laboratory beating of pulp. The description is limited to the sampling and beating of the pulp, the withdrawal and distribution of samples, and the beating equipment.</p><p>NOTE Beating is a preliminary step in testing the physical properties of pulp.</p><p>In principle, this method is applicable to all kinds of chemical and semi-chemical pulps. In practice, the method may not give satisfactory results with certai

11261,IS,,ISO 5267-1:1979,Pulps — Determination of drainability — Part 1: Schopper-Riegler method,Pâtes — Détermination de l'égouttabilité — Partie 1: Méthode Schopper-Riegler,1979-07-01,1,['85.040'],ISO/TC 6,9599,,[30933],"['en','fr']",5,

11262,IS,,ISO 5267-2:1980,Pulps — Determination of drainability — Part 2: 'Canadian Standard' freeness method,Pâtes — Détermination de l'égouttabilité — Partie 2: Méthode 'Canadian Standard',1980-11-01,1,['85.040'],ISO/TC 6,9599,,[26707],"['en','fr']",10,<p>Provides a measure of the rate at which a dilute suspension may be dewatered and is applicable to all kinds of pulp in aqueous suspension. Test results do not necessarily correlate with the drainage behaviour of pulp material on a commercial paper machine.</p>

26707,IS,,ISO 5267-2:2001,Pulps — Determination of drainability — Part 2: 'Canadian Standard' freeness method,Pâtes — Détermination de l'égouttabilité — Partie 2: Méthode de mesure de l'indice d'égouttage 'Canadian Standard',2001-09-27,2,['85.040'],ISO/TC 6,9599,[11262],"[86470,76080]","['en','fr']",14,"<p>This part of ISO 5267 specifies a method for determination of the drainability of a pulp suspension in water in terms</p><p>of the 'Canadian Standard' freeness in millilitres.</p><p>In principle, this method is applicable to all kinds of pulp in aqueous suspension.</p><p>NOTE Treatments which produce a large proportion of fines may induce an anomalous rise in freeness (false freeness), as<

11263,IS,,ISO 5269-1:1979,Pulps — Preparation of laboratory sheets for physical testing — Part 1: Conventional sheet-former method,Pâtes — Préparation des feuilles de laboratoire pour essais physiques — Partie 1: Méthode de la formette conventionnelle,1979-12-01,1,['85.040'],ISO/TC 6,9599,,[11264],"['en','fr']",4,

11264,IS,,ISO 5269-1:1998,Pulps — Preparation of laboratory sheets for physical testing — Part 1: Conventional sheet-former method,Pâtes — Préparation des feuilles de laboratoire pour essais physiques — Partie 1: Méthode de la formette conventionnelle,1998-07-30,2,['85.040'],ISO/TC 6,9599,[11263],[39340],"['en','fr']",7,

11265,IS,,ISO 5269-2:1980,Pulps — Preparation of laboratory sheets for physical testing — Part 2: Rapid-Koethen method,Pâtes — Préparation des feuilles de laboratoire pour essais physiques — Partie 2: Méthode Rapid-Köthen,1980-10-01,1,['85.040'],ISO/TC 6,9599,,[23404],"['en','fr']",5,

23404,IS,,ISO 5269-2:1998,Pulps — Preparation of laboratory sheets for physical testing — Part 2: Rapid-Köthen method,Pâtes — Préparation des feuilles de laboratoire pour essais physiques — Partie 2: Méthode Rapid-Köthen,1998-07-30,2,['85.040'],ISO/TC 6,9599,[11265],[39341],"['en','fr']",8,

4592,IS,,ISO 527-1:1993,Plastics — Determination of tensile properties — Part 1: General principles,Plastiques — Détermination des propriétés en traction — Partie 1: Principes généraux,1993-06-10,1,['83.080.01'],ISO/TC 61/SC 2,9599,[4591],[56045],"['en','fr']",9,"<p>Several different types of test specimen are defined to suit different types of material. The methods specified are selectively suitable for use with the following range of materials: rigid and semirigid thermoplastics moulding, including filled and reinforced compounds in addition to unfilled types, sheets and films, rigid and semirigid thermosetting moulding naterials including filled and reinforced compounds, and sheets includ

38236,IS,Amd,ISO 527-1:1993/Amd 1:2005,Plastics — Determination of tensile properties — Part 1: General principles — Amendment 1: Details of extensometer,Plastiques — Détermination des propriétés en traction — Partie 1: Principes généraux — Amendement 1: Détails de l'extensomètre,2005-09-05,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[56045],['en'],1,

23379,IS,Cor,ISO 527-1:1993/Cor 1:1994,Plastics — Determination of tensile properties — Part 1: General principles — Technical Corrigendum 1,Plastiques — Détermination des propriétés en traction — Partie 1: Principes généraux — Rectificatif technique 1,1994-04-14,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[56045],"['en','fr']",1,

56045,IS,,ISO 527-1:2012,Plastics — Determination of tensile properties — Part 1: General principles,Plastiques — Détermination des propriétés en traction — Partie 1: Principes généraux,2012-02-22,2,['83.080.01'],ISO/TC 61/SC 2,9599,"[38236,4592,23379]",[75824],"['en','fr','ru']",23,"<p>ISO 527-1:2012 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions. Several different types of test specimen are defined to suit different types of material which are detailed in subsequent parts of ISO 527.</p><p>The methods are used to investigate the tensile behaviour of the test specimens and for determining the tensile streng

4593,IS,,ISO 527-2:1993,Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics,Plastiques — Détermination des propriétés en traction — Partie 2: Conditions d'essai des plastiques pour moulage et extrusion,1993-06-10,1,['83.080.01'],ISO/TC 61/SC 2,9599,"[4591,12514]",[56046],"['en','fr']",5,"<p>The methods specified are selectively suitable for use with the following range of materials: rigid and semirigid thermoplastics moulding, extrusion and cast materials, including compounds filled and reinforced by e.g. short fibres, small rods, plates or granules but excluding textile fibres in addition to unfilled types, rigid and semirigid thermos

23380,IS,Cor,ISO 527-2:1993/Cor 1:1994,Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics — Technical Corrigendum 1,Plastiques — Détermination des propriétés en traction — Partie 2: Conditions d'essai des plastiques pour moulage et extrusion — Rectificatif technique 1,1994-04-14,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[56046],['fr'],,

56046,IS,,ISO 527-2:2012,Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics,Plastiques — Détermination des propriétés en traction — Partie 2: Conditions d'essai des plastiques pour moulage et extrusion,2012-02-22,2,['83.080.01'],ISO/TC 61/SC 2,9599,"[4593,23380]",[85822],"['en','fr','ru']",11,"<p>ISO 527-2:2012 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527‑1.</p>"

4594,IS,,ISO 527-3:1995,Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets,Plastiques — Détermination des propriétés en traction — Partie 3: Conditions d'essai pour films et feuilles,1995-07-27,1,['83.140.10'],ISO/TC 61/SC 11,9599,"[5774,4591]",[70307],"['en','fr']",5,"<p>Specifies the conditions for determining the tensile properties of plastics films or sheets less than 1 mm thick, based upon the general principles given in part 1. Cancels and replaces ISO/R 527:19966 as well as ISO 1184:1983, of which it constitutes a technical revision.</p>"

30480,IS,Cor,ISO 527-3:1995/Cor 1:1998,Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets — Technical Corrigendum 1,Plastiques — Détermination des propriétés en traction — Partie 3: Conditions d'essai pour films et feuilles — Rectificatif technique 1,1998-06-18,1,['83.140.10'],ISO/TC 61/SC 2,9599,,[70307],"['en','fr']",1,

35453,IS,Cor,ISO 527-3:1995/Cor 2:2001,Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets — Technical Corrigendum 2,Plastiques — Détermination des propriétés en traction — Partie 3: Conditions d'essai pour films et feuilles — Rectificatif technique 2,2001-04-12,1,['83.140.10'],ISO/TC 61/SC 11,9599,,[70307],"['en','fr']",1,

4595,IS,,ISO 527-4:1997,Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites,Plastiques — Détermination des propriétés en traction — Partie 4: Conditions d'essai pour les composites plastiques renforcés de fibres isotropes et orthotropes,1997-04-10,1,['83.120'],ISO/TC 61/SC 13,9599,[8494],[80369],"['en','fr']",11,

80369,IS,,ISO 527-4:2021,Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites,Plastiques — Détermination des propriétés en traction — Partie 4: Conditions d'essai pour les composites plastiques renforcés de fibres isotropes et orthotropes,2021-12-13,2,['83.120'],ISO/TC 61/SC 13,9599,[4595],[85809],"['en','fr']",27,"<p>This document specifies the test conditions for the determination of the tensile properties of isotropic and orthotropic fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.</p><p>NOTE 1 Unidirectional reinforced materials are covered by ISO 527-5.</p><p

22169,IS,,ISO 527-5:1997,Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites,Plastiques — Détermination des propriétés en traction — Partie 5: Conditions d'essai pour les composites plastiques renforcés de fibres unidirectionnelles,1997-04-10,1,['83.120'],ISO/TC 61/SC 13,9599,[8494],[52991],"['en','fr']",9,

52991,IS,,ISO 527-5:2009,Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites,Plastiques — Détermination des propriétés en traction — Partie 5: Conditions d'essai pour les composites plastiques renforcés de fibres unidirectionnelles,2009-06-26,2,['83.120'],ISO/TC 61/SC 13,9599,[22169],[80370],"['en','fr','ru']",12,"<p>ISO 527-5:2009 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.</p><p>The test method is suitable for all polymer matrix systems reinforced with unidirectional fibres

11267,IS,,ISO 5270:1979,Pulps — Laboratory sheets — Determination of physical properties,Pâtes — Feuilles de laboratoire — Détermination des propriétés physiques,1979-12-01,1,['85.040'],ISO/TC 6,9599,,[1457],"['en','fr']",3,

1457,IS,,ISO 5270:1998,Pulps — Laboratory sheets — Determination of physical properties,Pâtes — Feuilles de laboratoire — Détermination des propriétés physiques,1998-04-02,2,['85.040'],ISO/TC 6,9599,[11267],[56178],"['en','fr']",8,

56178,IS,,ISO 5270:2012,Pulps — Laboratory sheets — Determination of physical properties,Pâtes — Feuilles de laboratoire — Détermination des propriétés physiques,2012-09-28,3,['85.040'],ISO/TC 6,9599,[1457],[76079],"['en','fr']",8,"<p>ISO 5270:2012 specifies the relevant International Standards to be used for the determination of physical properties of laboratory sheets made of all kind of pulps. It is applicable to laboratory sheets prepared in accordance with ISO 5269-1, ISO 5269-2 or ISO 5269-3.</p><p>In ISO 5270:2012, it is left to the pulp producer and the pulp user to agree upon which properties are relevant to be tested. The results are, if applicable, reported in index form.</p>" 561