Withdrawn and superseded ISO standards — page 100 of 246

8352,IS,,ISO 3168:1986,"Aerospace — Self-locking, fixed, single-lug anchor nuts with counterbore, classification 1 100 MPa/235 degrees C","Aéronautique et espace — Écrous à river, à freinage interne, fixes, simple patte, avec chambrage, classification 1 100 MPa/235 degrés C",1986-06-19,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[27430],"['en','fr']",3,

8354,IS,,ISO 3170:1975,Petroleum products — Liquid hydrocarbons — Manual sampling,Produits pétroliers — Hydrocarbures liquides — Échantillonnage manuel,1975-07-01,1,['75.080'],ISO/TC 28,9599,,[8355],"['en','fr']",14,

8355,IS,,ISO 3170:1988,Petroleum liquids — Manual sampling,Produits pétroliers liquides — Échantillonnage manuel,1988-09-01,2,['75.080'],ISO/TC 28/SC 2,9599,[8354],[29283],"['en','fr']",23,"<p>Specifies procedures for liquid hydrocarbons, tank residues and deposite from fixed tanks, rail cars, road vehicles, ships and barges, drums and cans, or from liquids being pumped in pipelines. Does not apply for special products, such as aviation fuels, electrical insulating oils, liquefied petroleum gases, liquefied natural gases. bitumen and chemical products, nor to unstabilized crude oils having a Reid vapour pressure above 180 kPa.</p>"

25878,IS,Amd,ISO 3170:1988/Amd 1:1998,Petroleum liquids — Manual sampling — Amendment 1,Produits pétroliers liquides — Échantillonnage manuel — Amendement 1,1998-02-05,2,['75.080'],ISO/TC 28/SC 2,9599,,[29283],"['en','fr']",2,

29283,IS,,ISO 3170:2004,Petroleum liquids — Manual sampling,Produits pétroliers liquides — Échantillonnage manuel,2004-01-19,3,['75.080'],ISO/TC 28/SC 2,9599,"[25878,8355]","[80521,88551]","['en','fr','ru']",55,"<p>ISO 3170:2004 specifies the manual methods to be used for obtaining samples of liquid or semi-liquid hydrocarbons, tank residues and deposits from fixed tanks, railcars, road vehicles, ships and barges, drums and cans, or from liquids being pumped in pipelines.</p><p>ISO 3170:2004 applies to the sampling of petroleum products, crude oils and intermediate products, which are stored in tanks at or near atmospheric pressure, or transferred by pipelines, and are handled as liquids at

8356,IS,,ISO 3171:1975,Petroleum products — Liquid hydrocarbons — Automatic pipeline sampling,Produits pétroliers — Hydrocarbures liquides — Échantillonnage automatique en oléoduc,1975-12-01,1,"['75.180.30','75.080']",ISO/TC 28,9599,,[8357],"['en','fr']",12,

8359,IS,,ISO 3173:1974,Road vehicles — Apparatus for measurement of the opacity of exhaust gas from diesel engines operating under steady state conditions,Véhicules routiers — Dispositif pour le mesurage de l'opacité des gaz d'échappement des moteurs diesel fonctionnant en régime stabilisé,1974-12-01,1,"['13.040.50','43.180']",ISO/TC 22,9599,,[19551],"['en','fr']",26,

8360,IS,,ISO 3174:1981,Aircraft — Connections for checking hydraulic systems by ground appliances,Aéronefs — Raccords pour la vérification des circuits hydrauliques par des appareils au sol,1981-10-01,1,"['49.100','49.080']",ISO/TC 20/SC 10,9599,,[8361],"['en','fr']",4,

26819,IS,,ISO 3175-1:1998,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 1: Assessment of performance after cleaning and finishing","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 1: Évaluation de la résistance après le nettoyage et la finition",1998-08-20,1,['59.080.01'],ISO/TC 38/SC 2,9599,[2003],[54875],"['en','fr']",7,

36730,IS,Cor,ISO 3175-1:1998/Cor 1:2002,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 1: Assessment of performance after cleaning and finishing — Technical Corrigendum 1: .","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 1: Évaluation de la résistance après le nettoyage et la finition — Rectificatif technique 1: .",2002-10-10,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[54875],"['en','fr']",1,

54875,IS,,ISO 3175-1:2010,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 1: Assessment of performance after cleaning and finishing","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 1: Évaluation de la résistance après le nettoyage et la finition",2010-02-25,2,['59.080.01'],ISO/TC 38/SC 2,9599,"[36730,26819]",[65153],"['en','fr']",7,"<p>ISO 3175-1:2010 specifies a method for assessing textile articles which have been tested according to ISO 3175-2.</p><p>Fabric and garment properties, which can change on drycleaning and finishing, are identified and methods for assessing change using exis

8362,IS,,ISO 3175:1979,Textiles — Determination of dimensional change on dry cleaning in perchlorethylene — Machine method,Textiles — Détermination de la variation des dimensions au nettoyage à sec dans le perchloréthylène — Méthode à la machine,1979-07-01,2,['59.080.01'],ISO/TC 38/SC 2,9599,,[2003],"['en','fr']",4,

2003,IS,,ISO 3175:1995,Textiles — Evaluation of stability to machine dry-cleaning,Textiles — Evaluation de la stabilité au nettoyage à sec en machine,1995-08-10,3,['59.080.01'],ISO/TC 38/SC 2,9599,[8362],"[26820,26819]","['en','fr']",6,

26820,IS,,ISO 3175-2:1998,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 2: Procedure for testing performance when cleaning and finishing using tetrachloroethene","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 2: Mode opératoire pour évaluer la résistance au nettoyage et à la finition lors du traitement au tétrachloroéthylène",1998-08-20,1,['59.080.01'],ISO/TC 38/SC 2,9599,[2003],[54876],"['en','fr']",6,

36731,IS,Cor,ISO 3175-2:1998/Cor 1:2002,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 2: Procedure for testing performance when cleaning and finishing using tetrachloroethene — Technical Corrigendum 1: .","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 2: Mode opératoire pour évaluer la résistance au nettoyage et à la finition lors du traitement au tétrachloroéthylène — Rectificatif technique 1: .",2002-10-10,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[54876],"['en','fr']",1,

54876,IS,,ISO 3175-2:2010,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 2: Procedure for testing performance when cleaning and finishing using tetrachloroethene","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 2: Mode opératoire pour évaluer la résistance au nettoyage et à la finition lors du traitement au tétrachloroéthylène",2010-02-25,2,['59.080.01'],ISO/TC 38/SC 2,9599,"[26820,36731]",[65154],"['en','fr']",7,"<p>ISO 3175-2:2010 specifies drycleaning procedures for tetrachloroethene (perchloroethylene), using commercial drycleaning machines, for fabrics and garments. It comprises a

28997,IS,,ISO 3175-3:2003,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 3: Procedure for testing performance when cleaning and finishing using hydrocarbon solvents","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 3: Mode opératoire pour évaluer la résistance au nettoyage et à la finition avec des solvants hydrocarbonés",2003-10-10,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[65155],"['en','fr']",7,"<p>ISO 3175-3:2003 specifies drycleaning procedures for hydrocarbon solvents, using commercial drycleaning machines, for fabrics and garments. It comprises procedures for normal and sensitive mater

54873,IS,Cor,ISO 3175-3:2003/Cor 1:2009,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 3: Procedure for testing performance when cleaning and finishing using hydrocarbon solvents — Technical Corrigendum 1","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 3: Mode opératoire pour évaluer la résistance au nettoyage et à la finition avec des solvants hydrocarbonés — Rectificatif technique 1",2009-08-14,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[65155],"['en','fr']",1,

28998,IS,,ISO 3175-4:2003,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 4: Procedure for testing performance when cleaning and finishing using simulated wetcleaning","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 4: Mode opératoire pour évaluer la résistance au nettoyage et à la finition lors d'un nettoyage à l'eau simulé",2003-10-10,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[65156],"['en','fr']",11,"<p>ISO 3175-4:2003 specifies simulating professional wetcleaning procedures, using a reference machine for fabrics and garments. It comprises a normal process for normal materials, a mild proc

54874,IS,Cor,ISO 3175-4:2003/Cor 1:2009,"Textiles — Professional care, drycleaning and wetcleaning of fabrics and garments — Part 4: Procedure for testing performance when cleaning and finishing using simulated wetcleaning — Technical Corrigendum 1","Textiles — Entretien professionnel, nettoyage à sec et nettoyage à l'eau des étoffes et des vêtements — Partie 4: Mode opératoire pour évaluer la résistance au nettoyage et à la finition lors d'un nettoyage à l'eau simulé — Rectificatif technique 1",2009-08-14,1,['59.080.01'],ISO/TC 38/SC 2,9599,,[65156],"['en','fr']",1,

8365,IS,,ISO 3177:1975,Potassium hydroxide for industrial use — Determination of chlorides content — Photometric method,Hydroxyde de potassium à usage industriel — Dosage des chlorures — Méthode photométrique,1975-03-01,1,['71.060.40'],ISO/TC 47,9599,,[1870],"['en','fr']",3,"<p>Applicable to products having contents, expressed as chlorine, between 2 mg/kg and 50 mg/kg. For contents exceeding 50mg/kg the method specified in ISO 992 shall be used. The principle consists in quantitative displacement of the thiocyanate (SCN- ) ions of the mercury(II) thiocyanate by the cloride (Cl- ) ions contained in the test portion. Reaction of the thiocyanate ions with iron(III) nitrate to form iron(III) thi

8366,IS,,ISO 3178:1974,Steel wire ropes for general purposes — Terms of acceptance,Câbles en acier d'usages courants — Conditions de réception,1974-12-01,1,['77.140.65'],ISO/TC 105,9599,,[8367],"['en','fr']",6,

8368,IS,,ISO 3179:1974,Coniferous sawn timber — Nominal dimensions,Sciages de bois résineux — Dimensions nominales,1974-11-01,1,['79.040'],ISO/TC 218,9599,,[80059],"['en','fr']",2,"<p>Represents the combinatin of ISO/DIS 3179, 3181, and 3182 in a single document. Applies to unplaned square-edged and unedged shaped sawn timber 16 to 300 mm thick of different widths and differend shaped edges. The nominal thicknesses and widths are given in a table.</p>"

8370,IS,,ISO 3183-1:1996,Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 1: Pipes of requirement class A,Industries du pétrole et du gaz naturel — Tubes en acier pour le transport des fluides combustibles — Conditions techniques de livraison — Partie 1: Tubes de la classe de prescription A,1996-10-17,1,"['77.140.75','75.200']",ISO/TC 67,9599,[8369],"[36026,39071]","['en','fr']",111,

8369,IS,,ISO 3183:1980,Oil and natural gas industries — Steel line pipe,Industrie du pétrole et du gaz naturel — Tubes en acier pour conduites,1980-09-01,1,"['77.140.75','75.200']",ISO/TC 67,9599,,"[8371,8372,8370]","['en','fr']",40,

8371,IS,,ISO 3183-2:1996,Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 2: Pipes of requirements class B,Industries du pétrole et du gaz naturel — Tubes en acier pour le transport des fluides combustibles — Conditions techniques de livraison — Partie 2: Tubes de la classe de prescription B,1996-03-14,1,"['77.140.75','75.200']",ISO/TC 67,9599,[8369],"[36025,39071]","['en','fr']",48,<p>Specifies the technical delivery conditions for unalloyed and alloyed seamless and welded steel pipes. Includes quality and testing requirements. Applies for pipes which are normally used for the transmission of combustible fluids. Does not apply for cast s

39071,IS,,ISO 3183:2007,Petroleum and natural gas industries — Steel pipe for pipeline transportation systems,Industries du pétrole et du gaz naturel — Tubes en acier pour les systèmes de transport par conduites,2007-03-15,2,"['77.140.75','75.200']",ISO/TC 67/SC 2,9599,"[8371,8372,33881,8370]",[56843],"['en','ru']",143,<p>ISO 3183:2007 specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries.</p><p>ISO 3183:2007 is not applicable to cast pipe.</p>

56843,IS,,ISO 3183:2012,Petroleum and natural gas industries — Steel pipe for pipeline transportation systems,Industries du pétrole et du gaz naturel — Tubes en acier pour les systèmes de transport par conduites,2012-11-05,3,"['77.140.75','75.200']",ISO/TC 67/SC 2,9599,[39071],"[70612,76676]","['en','fr']",179,<p>ISO 3183:2012 specifies requirements for the manufacture of two product specification levels (PSL 1 and PSL 2) of seamless and welded steel pipes for use in pipeline transportation systems in the petroleum and natural gas industries.</p><p>ISO 3183:2012 is not applicable to cast pipe.</p>

72122,IS,Amd,ISO 3183:2012/Amd 1:2017,Petroleum and natural gas industries — Steel pipe for pipeline transportation systems — Amendment 1,Industries du pétrole et du gaz naturel — Tubes en acier pour les systèmes de transport par conduites — Amendement 1,2017-12-06,3,"['77.140.75','75.200']",ISO/TC 67/SC 2,9599,,[76676],"['en','fr']",16,

8372,IS,,ISO 3183-3:1999,Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 3: Pipes of requirement class C,Industries du pétrole et du gaz naturel — Tubes en acier pour le transport des fluides combustibles — Conditions techniques de livraison — Partie 3: Tubes de classe de prescription C,1999-04-15,1,"['77.140.75','75.200']",ISO/TC 67,9599,[8369],"[38505,39071]","['en','fr']",54,

33881,IS,Cor,ISO 3183-3:1999/Cor 1:2000,Petroleum and natural gas industries — Steel pipe for pipelines — Technical delivery conditions — Part 3: Pipes of requirement class C — Technical Corrigendum 1,Industries du pétrole et du gaz naturel — Tubes en acier pour le transport des fluides combustibles — Conditions techniques de livraison — Partie 3: Tubes de classe de prescription C — Rectificatif technique 1,2000-03-23,1,"['77.140.75','75.200']",ISO/TC 67,9599,,"[38505,39071]",['fr'],,

8374,IS,,ISO 3184:1974,Reach and straddle fork lift trucks — Stability tests,Chariots à mât ou fourche rétractable et chariots à fourche entre longerons — Essais de stabilité,1974-12-01,1,['53.060'],ISO/TC 110,9599,,[8375],"['en','fr']",7,

8375,IS,,ISO 3184:1998,Reach and straddle fork-lift trucks — Stability tests,Chariots à mât ou à fourche rétractable et chariots à fourche entre longerons — Essais de stabilité,1998-12-20,2,['53.060'],ISO/TC 110/SC 2,9599,[8374],[41212],"['en','fr']",11,

33238,IS,Cor,ISO 3184:1998/Cor 1:2000,Reach and straddle fork-lift trucks — Stability tests — Technical Corrigendum 1,Chariots à mât ou à fourche rétractable et chariots à fourche entre longerons — Essais de stabilité — Rectificatif technique 1,2000-06-08,2,['53.060'],ISO/TC 110/SC 2,9599,,[41212],"['en','fr']",4,

8376,IS,,ISO 3185:1993,"Aerospace — Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions","Aéronautique et espace — Vis à tête bihexagonale normale, avec tige normale et filetage MJ court ou de longueur moyenne, en matériau métallique, revêtues ou non revêtues, des classes de résistance inférieures ou égales à 1 100 MPa — Dimensions",1993-12-23,1,['49.030.20'],ISO/TC 20/SC 4,9599,,[41823],"['en','fr']",3,"<p>Specifies the configuration, dimensions, and tolerances. Is intended for the drawing up of aerospace product standards.</p>"

41823,IS,,ISO 3185:2008,"Aerospace — Bolts, normal bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions","Aéronautique et espace — Vis à tête bihexagonale normale, avec tige normale et filetages MJ courts ou de longueur moyenne, en matériau métallique, revêtues ou non revêtues, des classes de résistance inférieures ou égales à 1 100 MPa — Dimensions",2008-08-18,2,['49.030.20'],ISO/TC 20/SC 4,9599,[8376],[77131],['en'],5,"<p>ISO 3185:2008 specifies the dimensions of normal bihexagonal head bolts, with close or large tolerance normal shank and short or medium length MJ threads, in

8377,IS,,ISO 3186:1994,"Aerospace — Bolts, large bihexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes 1 250 MPa to 1 800 MPa — Dimensions","Aéronautique et espace — Vis à tête bihexagonale large, avec tige normale et filetage MJ court ou de longueur moyenne, en matériau métallique, revêtues ou non revêtues, des classes de résistance 1 250 MPa à l 800 MPa — Dimensions",1994-10-06,1,['49.030.20'],ISO/TC 20/SC 4,9599,,"[41822,33213]","['en','fr']",3,<p>The document specifies the dimension of bihexagonal nuts for use in aerospace fastener systems.</p>

8385,IS,,ISO 3191:1985,"Aerospace — Self-locking, fixed, single-lug anchor nuts, reduced series, with counterbore, strength classification 1 100 MPa and maximum operating temperature 235 degrees C","Aéronautique et espace — Écrous à river, à freinage interne, fixes, simple patte, série réduite, avec chambrage, de classe de résistance 1 100 MPa pour température maximale d'utilisation 235 degrés C",1985-07-18,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[8386],"['en','fr']",3,

8388,IS,,ISO 3193:1991,"Aerospace — Bolts, normal hexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions","Aéronautique et espace — Vis à tête hexagonale normale, avec tige normale et filetage MJ court ou de longueur moyenne, en matériau métallique, revêtues ou non revêtues, des classes de résistance inférieures ou égales à 1 100 MPa — Dimensions",1991-01-14,1,['49.030.20'],ISO/TC 20/SC 4,9599,,"[41821,31740]","['en','fr']",3,"<p>Specifies the dimensions of these bolts. Is intended for the drawing-up of aerospace product standards. Dimensions and tolerances are given in figure 1 and

8389,IS,Cor,ISO 3193:1991/Cor 1:1992,"Aerospace — Bolts, normal hexagonal head, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions — Technical Corrigendum 1","Aéronautique et espace — Vis à tête hexagonale normale, avec tige normale et filetage MJ court ou de longueur moyenne, en matériau métallique, revêtues ou non revêtues, des classes de résistance inférieures ou égales à 1 100 MPa — Dimensions — Rectificatif technique 1",1992-02-06,1,['49.030.20'],ISO/TC 20/SC 4,9599,,"[41821,31740]","['en','fr']",1,<p>Modifies Table 1 (page 3).</p>

8390,IS,,ISO 3194:1975,Potassium hydroxide for industrial use — Determination of sulphur compounds — Method by reduction and titrimetry,Hydroxyde de potassium à usage industriel — Dosage des composés soufrés — Méthode par réduction et titrimétrie,1975-08-01,1,['71.060.40'],ISO/TC 47,9599,,[8391],"['en','fr']",6,"<p>Applicable to products the content of which, expressed as sulphate, is equal or more than 5 mg/kg. The principle consists in the reduction of the sulphur compounds to hydrogen sulphide by heating with a mixture of hydriodic acid and hypophosphorous acid. Distillation of the hydrogen sulphide by a current of purified oxygen-free nitrogen in a mixture of sodium hydroxide and acetone

8395,IS,,ISO 3198:1975,Sodium hydroxide for industrial use — Determination of sulphur compounds — Method by reduction and titrimetry,Hydroxyde de sodium à usage industriel — Dosage des composés soufrés — Méthode par réduction et titrimétrie,1975-08-01,1,['71.060.40'],ISO/TC 47,9599,,[8396],"['en','fr']",6,"<p>Applicable to products the content of which, expressed as sulphate, is equal or more than 5 mg/kg. The principle consists in the reduction of the sulphur compounds to hydrogen sulphide by heating with a mixture of hydriodic acid and hypophosphorous acid. Distillation of the hydrogen sulphide by a current of oxygen-free nitrogen in a mixture of sodium hydroxide and acetone. Titration of

63534,IS,,ISO 32000-2:2017,Document management — Portable document format — Part 2: PDF 2.0,Gestion de documents — Format de document portable — Partie 2: PDF 2.0,2017-07-27,1,"['35.240.30','37.100.99']",ISO/TC 171/SC 2,9599,,[75839],['en'],971,"<p>ISO 32000-2:2017 specifies a digital form for representing electronic documents to enable users to exchange and view electronic documents independent of the environment in which they were created or the environment in which they are viewed or printed. It is intended for developers of software that creates PDF files (PDF writers), software that reads existing PDF files and (usually) interprets their contents for display (PDF readers), software that

8399,IS,,ISO 3201:1975,"Sodium and potassium silicates for industrial use — Determination of iron content — 1,10- Phenanthroline photometric method","Silicates de sodium et de potassium à usage industriel — Dosage du fer — Méthode photométrique à la 1,10- phénanthroline",1975-03-01,1,['71.060.50'],ISO/TC 47,9599,,[8400],"['en','fr']",2,

8401,IS,,ISO 3202:1991,"Aerospace — Screws, pan head, internal offset cruciform ribbed drive, threaded to head, MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa — Dimensions","Aéronautique et espace — Vis à tête cylindrique, à empreinte cruciforme déportée avec saillies antidérapantes, filetées jusqu'à proximité de la tête, à filetage MJ, en matériau métallique, revêtues ou non revêtues, des classes de résistance inférieures ou égales à 1 100 MPa — Dimensions",1991-11-21,1,['49.030.20'],ISO/TC 20/SC 4,9599,,[22609],"['en','fr']",3,

8406,IS,,ISO 3207:1975,Statistical interpretation of data — Determination of a statistical tolerance interval,Interprétation statistique des données — Détermination d'un intervalle statistique de dispersion,1975-05-01,1,['03.120.30'],ISO/TC 69,9599,,[38772],"['en','fr']",15,"<p>Methods are specified enabling a sample to be used as the basis for determining a statistical tolerance interval, which may be two-sided or one-sided. They are applicable only where the sample unity may be assumed to have been selected at random and are independent, and if the distribution is normal (if appropriate, transforming the variate may make it normal). Tables 1 and 2 are applicable to the case where the stand

8409,IS,,ISO 3209:1989,"Aerospace — Nuts, anchor, self-locking, floating, two-lug, with counterbore, with MJ threads, coated or uncoated, classification 1 100 MPa/235 degrees C, 1 100 MPa/315 degrees C or 1 100 MPa/425 degrees C — Dimensions","Aéronautique et espace — Écrous à river, à freinage interne, à filetage MJ, flottants, double patte, avec chambrage, revêtus ou non revêtus, de classification 1 100 MPa/235 degrés C, 1 100 MPa/315 degrés C ou 1 100 MPa/425 degrés C — Dimensions",1989-10-05,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[27432],"['en','fr']",2,

27432,IS,,ISO 3209:1998,"Aerospace — Nuts, anchor, self-locking, floating, two lug, with counterbore, with MJ threads, classifications: 1 100 MPa (at ambient temperature )/235 degrees C, 1 100 MPa (at ambient temperature )/315 degrees C and 1 100 MPa (at ambient temperature)/425 degrees C — Dimensions","Aéronautique et espace — Écrous à river, à freinage interne, flottants, double patte, avec chambrage, à filetage MJ, classifications: 1 100 MPa (à température ambiante)/235 degrés C, 1 100 MPa (à température ambiante)/315 degrés C et 1 100 MPa (à température ambiante)/425 degrés C — Dimensions",1998-11-26,2,['49.030.30'],ISO/TC 20/SC 4,9599,[8409],[66316],"['en','fr']",3,

8410,IS,,ISO 3210:1983,Anodizing of aluminium and its alloys — Assessment of quality of sealed anodic oxide coatings by measurement of the loss of mass after immersion in phosphoric-chromic acid solution,Anodisation de l'aluminium et de ses alliages — Évaluation de la qualité des couches anodiques colmatées par mesurage de la perte de masse après immersion en solution phosphochromique,1983-12-01,2,['25.220.20'],ISO/TC 79/SC 2,9599,,"[51489,1438]","['en','fr']",3,<p>This second edition cancels and replaces the first edition (ISO 3210/1974). Specifies a destructive arbitration method. Applies to anodic coatings provided for weathering exposing or for protective purposes in corrosive media. Doe

51489,IS,,ISO 3210:2010,Anodizing of aluminium and its alloys — Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution,Anodisation de l'aluminium et de ses alliages — Évaluation de la qualité des couches anodiques colmatées par mesurage de la perte de masse après immersion en solution phosphochromique,2010-07-01,3,['25.220.20'],ISO/TC 79/SC 2,9599,[8410],[67983],"['en','fr']",6,"<p>ISO 3210:2010 specifies methods of assessing the quality of sealed anodic oxidation coatings on aluminium and its alloys by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution.</p><p>

67983,IS,,ISO 3210:2017,Anodizing of aluminium and its alloys — Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in acid solution(s),Anodisation de l'aluminium et de ses alliages — Évaluation de la qualité des couches anodiques colmatées par mesurage de la perte de masse après immersion en solution(s) acide(s),2017-10-30,4,['25.220.20'],ISO/TC 79/SC 2,9599,[51489],[88866],"['en','fr']",7,"<p>ISO 3210:2017 specifies methods of assessing the quality of sealed anodic oxidation coatings on aluminium and its alloys by measurement of the loss of mass after immersion in acid solution(s).</p><p>It consists of the following two methods.</p><

52830,IS,,ISO 32100:2010,Rubber- or plastics-coated fabrics — Physical and mechanical tests — Determination of flex resistance by the flexometer method,Supports textiles revêtus de caoutchouc ou de plastique — Essais physiques et mécaniques — Détermination de la résistance à la flexion à l'aide d'un flexomètre,2010-11-29,1,['59.080.40'],ISO/TC 45/SC 4,9599,,[71078],"['en','fr']",13,<p>ISO 32100:2010 specifies a test method for determining the flex resistance of rubber- or plastics-coated fabrics in the folded condition. The test method is applicable only to products which can be clamped in the test apparatus used and to products with which the fold made in the test specimen can be caused to

8411,IS,,ISO 3211:1977,Anodizing of aluminium and its alloys — Assessment of resistance of anodic oxide coatings to cracking by deformation,Anodisation de l'aluminium et de ses alliages — Évaluation de la résistance des couches anodiques à la formation de criques par déformation,1977-02-01,2,['25.220.20'],ISO/TC 79/SC 2,9599,,[51491],"['en','fr']",2,"<p>This assessment method is applicable particularly to sheet with thin anodic oxide coatings. ISO 3211 describes principle, apparatus, procedure, expression of results and test report. A figure shows the measuring instrument used.</p>"

51491,IS,,ISO 3211:2010,Anodizing of aluminium and its alloys — Assessment of resistance of anodic oxidation coatings to cracking by deformation,Anodisation de l'aluminium et de ses alliages — Évaluation de la résistance des couches anodiques à la formation de criques par déformation,2010-08-20,3,['25.220.20'],ISO/TC 79/SC 2,9599,[8411],[72173],"['en','fr']",5,"<p>ISO 3211:2010 specifies an empirical method for assessing the resistance of anodic oxidation coatings to cracking by deformation.</p><p>The method is applicable particularly to sheet material with anodic oxidation coatings of thickness less than 5 µm, and is useful for development purposes.</p>"

8412,IS,,ISO 3212:1975,Polypropylene pipes — Burst test requirements,Tubes en polypropylène — Spécifications pour les essais de résistance à l'écartement,1975-09-01,1,['23.040.20'],ISO/TC 138/SC 5,9599,,[8413],"['en','fr']",1,

8414,IS,,ISO 3213:1975,Polypropylene pipes — Reduction of permissible stress as a function of time and temperature,Tubes en polypropylène — Dégressivité des tensions de charge en fonction du temps et de la température,1975-09-01,1,['23.040.20'],ISO/TC 138,9599,,[22752],"['en','fr']",1,

22752,IS,,ISO 3213:1996,Polypropylene (PP) pipes — Effect of time and temperature on expected strength,Tubes en polypropylène (PP) — Influence du temps et de la température sur la résistance espérée,1996-08-15,2,['23.040.20'],ISO/TC 138/SC 5,9599,[8414],[46420],"['en','fr']",10,"<p>Gives the minimum values for expected strength of polypropylene pipes as a function of time and temperature in the form of reference lines, for use in calculations.</p>"

8415,IS,,ISO 3214:1974,Oil of Litsea cubeba,Huile essentielle de Litsea cubeba,1974-08-01,1,['71.100.60'],ISO/TC 54,9599,,"[33747,8416]","['en','fr']",2,

8417,IS,,ISO 3215:1974,Oils of nutmeg,Huiles essentielles de noix muscade,1974-08-01,1,['71.100.60'],ISO/TC 54,9599,,[8418],"['en','fr']",1,

8419,IS,,ISO 3216:1974,Oil of cassia,Huile essentielle de cannelle de Chine,1974-08-01,1,['71.100.60'],ISO/TC 54,9599,,[8420],"['en','fr']",2,

8423,IS,,ISO 3218:1976,Essential oils — Principles of nomenclature,Huiles essentielles — Principes de nomenclature,1976-06-01,1,['71.100.60'],ISO/TC 54,9599,,"[56820,8424]","['en','fr']",2,"<p>To distinguish essential oils from fixed oils, the expression 'oil of ...' shall be used. The commonly accepted trivial name of the plant shall follow these words. When no trivial name exists, the complete botanical name shall be used instead. If more than one part of the plant can be used for the extraction of essential oil, the name of the part employed shall follow the trivial name of the plant. If necessary the name of the country or area the plants are coming from shall precede the trivial name an

8425,IS,,ISO 3219:1977,"Plastics — Polymers in the liquid, emulsified or dispersed state — Determination of viscosity with a rotational viscometer working at defined shear rate",Plastiques — Polymères à l'état liquide ou en émulsion ou dispersion — Détermination de la viscosité au moyen d'un viscosimètre rotatif à gradient de vitesse de cisaillement défini,1977-12-01,1,['83.080'],ISO/TC 61,9599,,[8426],"['en','fr']",3,

8426,IS,,ISO 3219:1993,Plastics — Polymers/resins in the liquid state or as emulsions or dispersions — Determination of viscosity using a rotational viscometer with defined shear rate,"Plastiques — Polymères/résines à l'état liquide, en émulsion ou en dispersion — Détermination de la viscosité au moyen d'un viscosimètre rotatif à gradient de vitesse de cisaillement défini",1993-09-23,2,['83.080.01'],ISO/TC 35/SC 9,9599,"[8425,17058]","[76032,76033]","['en','fr']",8,<p>General specification for rotational viscometers for the determination of the viscosity of polymers in the liquid or liquidlike state.</p>

8429,IS,,ISO 3221:1989,"Aerospace — Nuts, anchor, self-locking, fixed, 90 degrees corner, with counterbore, with MJ threads, coated or uncoated, classification 1 100 MPa/235 degrees C, 1 100 MPa/315 degrees C or 1 100 MPa/425 degrees C — Dimensions","Aéronautique et espace — Écrous à river, à freinage interne, à filetage MJ, fixes, d'angle 90 degrés, avec chambrage, revêtus ou non revêtus, de classification 1 100 MPa/235 degrés C, 1 100 MPa/315 degrés C ou 1 100 MPa/ 425 degrés C — Dimensions",1989-10-05,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[27433],"['en','fr']",2,

8430,IS,,ISO 3222:1989,"Aerospace — Nuts, anchor, self-locking, fixed, closed corner, reduced series, with counterbore, with MJ threads, coated or uncoated, classification 1 100 MPa/235 degrees C, 1 100 MPa/315 degrees C or 1 100 MPa/425 degrees C — Dimensions","Aéronautique et espace — Écrous à river, à freinage interne, à filetage MJ, fixes, d'angle, série réduite, avec chambrage, revêtus ou non revêtus, de classification 1 100 MPa/ 235 degrés C, 1 100 MPa/315 degrés C ou 1 100 MPa/425 degrés C — Dimensions",1989-10-05,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[27434],"['en','fr']",2,

8431,IS,,ISO 3223:1989,"Aerospace — Nuts, anchor, self-locking, fixed, two-lug, with counterbore, with MJ threads, coated or uncoated, classification 1 100 MPa/ 235 degrees C, 1 100 MPa/315 degrees C or 1 100 MPa/425 degrees C — Dimensions","Aéronautique et espace — Écrous à river, à freinage interne, à filetage MJ, fixes, double patte, avec chambrage, revêtus ou non revêtus, de classification 1 100 MPa/235 degrés C, 1 100 MPa/315 degrés C ou 1 100 MPa/425 degrés C — Dimensions",1989-10-04,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[27435],"['en','fr']",2,

8432,IS,,ISO 3224:1985,"Aerospace — Self-locking, floating, single-lug anchor nuts, with counterbore, classification 1 100 MPa/235 degrees C","Aéronautique et espace — Écrous à river, à freinage interne, flottants, simple patte, avec chambrage, classification 1 100 MPa/235 degrés C",1985-12-19,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[27505],"['en','fr']",3,

8433,IS,,ISO 3225:1985,"Aerospace — Self-locking, fixed, two lug anchor nuts, reduced series, with counterbore, strength classification 1 100 MPa and maximum operating temperature 235 degrees C","Aéronautique et espace — Écrous à river, à freinage interne, fixes, double patte, série réduite, avec chambrage, de classe de résistance 1 100 MPa pour température maximale d'utilisation 235 degrés C",1985-06-20,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[27506],"['en','fr']",3,

8436,IS,,ISO 3228:1977,Rolling bearings — Bearings with spherical outside surface and extended inner ring width — Cast and pressed housings,Roulements — Roulements à surface extérieure sphérique et à bague intérieure large — Paliers moulés et paliers emboutis,1977-11-01,2,['21.100.20'],ISO/TC 4,9599,,[8437],"['en','fr']",5,

8437,IS,,ISO 3228:1993,Rolling bearings — Cast and pressed housings for insert bearings,Roulements — Logements moulés et emboutis pour roulements 'insert',1993-08-26,3,['21.100.20'],ISO/TC 4/SC 6,9599,[8436],"[43571,53719]","['en','fr']",8,"<p>Specifies boundary dimensions and tolerances for cast and pressed housings for insert bearings for which boundary dimensions are given in ISO 9628. Applies to plummer block housings, flanged housings and take-up housings. The inclusion of relubrication features is optional.</p>"

8440,IS,,ISO 3231:1974,Paints and varnishes — Determination of resistance to humid atmospheres containing sulphur dioxide,Peintures et vernis — Détermination de la résistance aux atmosphères humides contenant du dioxyde de soufre,1974-11-01,1,['87.040'],ISO/TC 35/SC 9,9599,,[8441],"['en','fr']",3,

8441,IS,,ISO 3231:1993,Paints and varnishes — Determination of resistance to humid atmospheres containing sulfur dioxide,Peintures et vernis — Détermination de la résistance aux atmosphères humides contenant du dioxyde de soufre,1993-01-21,2,['87.040'],ISO/TC 156,9599,[8440],[73301],"['en','fr']",5,"<p>The principle of the procedure specified is to expose a coated test panel to specified humid atmospheres containing sulfur dioxide. A volume of 0,2 litre, measured at atmospheric pressure, is generally recommended for testing coatings of thickness not exceeding approximately 40 µm. The effects of exposure are evaluated by criteria agreed in advance between the interested parties, these criteri

51937,IS,,ISO 3233-1:2013,Paints and varnishes — Determination of the percentage volume of non-volatile matter — Part 1: Method using a coated test panel to determine non-volatile matter and to determine dry film density by the Archimedes principle,Peintures et vernis — Détermination du pourcentage en volume de matière non volatile — Partie 1: Méthode utilisant un panneau d'essai revêtu pour déterminer la matière non volatile et pour déterminer la masse volumique du feuil sec par le principe d'Archimède,2013-01-08,1,['87.040'],ISO/TC 35/SC 9,9599,"[20351,32384]",[77255],"['en','fr']",12,"<p>ISO 3233-1:2013 describes a procedure for determining the non-volatile matter by volume, NV<sub>V</sub

8443,IS,,ISO 3233:1984,Paints and varnishes — Determination of volume of dry coating (non-volatile matter) obtained from a given volume of liquid coating,Peintures et vernis — Détermination du volume de revêtement sec (matières non volatiles) obtenu à partir d'un volume donné de produit liquide,1984-01-01,2,['87.040'],ISO/TC 35/SC 9,9599,,[20351],"['en','fr']",5,

20351,IS,,ISO 3233:1998,Paints and varnishes — Determination of percentage volume of non-volatile matter by measuring the density of a dried coating,Peintures et vernis — Détermination du pourcentage en volume de matières non volatiles par mesurage de la masse volumique d'un revêtement sec,1998-08-20,3,['87.040'],ISO/TC 35/SC 9,9599,[8443],[51937],"['en','fr']",9,

32384,IS,Cor,ISO 3233:1998/Cor 1:1999,Paints and varnishes — Determination of percentage volume of non-volatile matter by measuring the density of a dried coating — Technical Corrigendum 1,Peintures et vernis — Détermination du pourcentage en volume de matières non volatiles par mesurage de la masse volumique d'un revêtement sec — Rectificatif technique 1,1999-08-05,3,['87.040'],ISO/TC 35/SC 9,9599,,[51937],"['en','fr']",1,

55331,IS,,ISO 3233-2:2014,Paints and varnishes — Determination of the percentage volume of non-volatile matter — Part 2: Method using the determination of non-volatile-matter content in accordance with ISO 3251 and determination of dry film density on coated test panels by the Archimedes principle,Peintures et vernis — Détermination du pourcentage en volume de matière non volatile — Partie 2: Méthode utilisant la teneur en matière non volatile déterminée conformément à l'ISO 3251 et la masse volumique du feuil sec déterminée par le principe d'Archimède sur des panneaux d'essai revêtus,2014-06-24,1,['87.040'],ISO/TC 35/SC 9,9599,,[73852],"['en','fr','ru']",10,"<p>ISO 3233-2:2014 specifies a m

8449,IS,,ISO 3238:1975,Sodium sulphate for industrial use — Determination of calcium content — EDTA complexometric method,Sulfate de sodium à usage industriel — Dosage du calcium — Méthode complexométrique à l'EDTA,1975-07-01,1,['71.060.50'],ISO/TC 47,9599,,[8450],"['en','fr']",3,<p>Applicable to products the Ca content of which exceeds 0.002 % (m/m). Extraction of a test portion with dilute acid and separation of the insoluble residue. Titration of the calcium with standard volumetric disodium ethylenediamine-NNN'N'-tetra-acetate dihydrate (EDTA) solution in the presence of glyoxal-bis(hydoxy-2-anil) as indicator.</p>

8451,IS,,ISO 3239:1975,"Sodium sulphate for industrial use — Determination of iron content — 1,10- Phenanthroline photometric method","Sulfate de sodium à usage industriel — Dosage du fer — Méthode photométrique à la 1,10- phénanthroline",1975-07-01,1,['71.060.50'],ISO/TC 47,9599,,[8452],"['en','fr']",4,"<p>Applicable to products the Fe content of which is equal to or more than 0.0003 % (m/m). Dissolution of the test sample in delute hydrochloric acid and bromine water by heating. Preliminary reduction of the iron(III) by hydroxylammonium chloride. Formation of the iron(II)-1,10-phenanthroline complex in a buffered medium. Photometric measurement of the coloured complex at a wavelength of ab

4267,IS,,ISO 324:1978,Textile machinery and accessories — Cones for cross winding for dyeing purposes — Half angle of the cone 4 degrees 20',Matériel pour l'industrie textile — Cônes pour bobinage croisé pour la teinture — Demi angle du cône 4 degrés 20',1978-05-01,1,['59.120.20'],ISO/TC 72/SC 1,9599,,[21963],"['en','fr']",2,

8455,IS,,ISO 3243:1975,Keyboards for countries whose languages have alphabetic extenders — Guidelines for harmonization,Claviers pour les pays dont la langue utilise des caractères alphabétiques supplémentaires — Guide pour l'harmonisation,1975-02-01,1,['35.180'],ISO/IEC JTC 1,9599,,"[17914,17910,17911,17915,17912,17909,17913]","['en','fr']",4,

8456,IS,,ISO 3244:1974,Office machines and data processing equipment — Principles governing the positioning of control keys on keyboards,Machines de bureau et machines employées en traitement de l'information — Principes directeurs pour l'affectation des touches de commande sur les claviers,1974-12-01,1,"['35.180','35.260']",ISO/IEC JTC 1,9599,,[8457],"['en','fr']",4,

8457,IS,,ISO 3244:1984,Office machines and data processing equipment — Principles governing the positioning of control keys on keyboards,Machines de bureau et machines employées en traitement de l'information — Principes directeurs pour l'affectation des touches de commande sur les claviers,1984-04-01,1,"['35.180','35.260']",ISO/IEC JTC 1,9599,[8456],"[17914,17910,17911,17915,17912,17909,17913]","['en','fr']",4,

8458,IS,,ISO 3245:1974,"Rolling bearings — Needle roller bearings, drawn cup, without inner ring — Metric series — Boundary dimensions and tolerances",Roulements à aiguilles — Douilles à aiguilles sans bague intérieure — Séries métriques — Dimensions d'encombrement et tolérances,1974-12-01,1,['21.100.20'],ISO/TC 4/SC 5,9599,,[20525],"['en','fr']",4,

20525,IS,,ISO 3245:1997,"Rolling bearings — Needle roller bearings, drawn cup without inner rings — Boundary dimensions and tolerances",Roulements — Douilles à aiguilles sans bague intérieure — Dimensions d'encombrement et tolérances,1997-01-30,2,['21.100.20'],ISO/TC 4/SC 5,9599,[8458],[37776],"['en','fr']",7,<p>Specifies a general plan for boundary dimensions and preferred dimensions to be used. For closed end drawn cups dimensions of the end are specified. In addition it gives tolerances and a method for checking of the needle roller complement bore diameter.</p>

37776,IS,,ISO 3245:2007,"Rolling bearings — Needle roller bearings, drawn cup without inner ring — Boundary dimensions and tolerances",Roulements — Douilles à aiguilles sans bague intérieure — Dimensions d'encombrement et tolérances,2007-12-13,3,['21.100.20'],ISO/TC 4/SC 5,9599,[20525],[61183],"['en','fr','ru']",6,"<p>ISO 3245:2007 specifies the boundary dimensions and preferred dimensions to be used for drawn cup needle roller bearings without inner ring as well as the minimum chamfer dimension limits. Also specified are the closed end thickness dimensions for bearings with closed end drawn cups.</p><p>In addition, dimensional tolerances and methods for checking the needle roller complement

61183,IS,,ISO 3245:2015,"Rolling bearings — Needle roller bearings with drawn cup and without inner ring — Boundary dimensions, geometrical product specifications (GPS) and tolerance values","Roulements — Douilles à aiguilles sans bague intérieure — Dimensions d'encombrement, spécification géométrique des produits (GPS) et valeurs de tolérance",2015-12-14,4,['21.100.20'],ISO/TC 4/SC 5,9599,[37776],[85376],"['en','fr']",11,"<p>ISO 3245:2015 specifies the boundary dimensions and preferred dimensions to be used for drawn cup needle roller bearings without inner ring as well as the minimum chamfer dimension limits. Also specified are the closed end thickness dimensions for bearings with one clos

8461,IS,,ISO 3248:1975,Paints and varnishes — Determination of the effect of heat,Peintures et vernis — Détermination des effets de la chaleur,1975-02-01,1,['87.040'],ISO/TC 35/SC 9,9599,,[29496],"['en','fr']",2,

29496,IS,,ISO 3248:1998,Paints and varnishes — Determination of the effect of heat,Peintures et vernis — Détermination des effets de la chaleur,1998-03-19,2,['87.040'],ISO/TC 35/SC 9,9599,[8461],[64818],"['en','fr']",4,

8462,IS,,ISO 3249:1975,Reciprocating internal combustion engines — Definitions of locations on an engine,Moteurs alternatifs à combustion interne — Définitions des emplacements sur un moteur,1975-04-01,1,['27.020'],ISO/TC 70,9599,,[5797],"['en','fr']",2,

8463,IS,,ISO 3251:1974,Paint media — Determination of volatile and non-volatile matter,Liants pour peintures — Détermination des matières volatiles et non volatiles,1974-11-01,1,['87.060.20'],ISO/TC 35,9599,,[8464],"['en','fr']",2,

8464,IS,,ISO 3251:1993,"Paints and varnishes — Determination of non-volatile matter of paints, varnishes and binders for paints and varnishes","Peintures et vernis — Détermination de l'extrait sec des peintures, des vernis et des liants pour peintures et vernis",1993-09-23,2,"['87.040','87.060.20']",ISO/TC 35,9599,"[8463,6107]",[30333],"['en','fr']",7,"<p>Specifies a test method for determining the non-volatile matter content by mass of paints and varnishes, as well as resins and resin solutions that are intended for use as binders for paints and varnishes. Annex A gives required supplementary information, annex B describes the test conditions.</p>"

30333,IS,,ISO 3251:2003,"Paints, varnishes and plastics — Determination of non-volatile-matter content","Peintures, vernis et plastiques — Détermination de l'extrait sec",2003-02-25,3,"['83.080.01','87.040','87.060.20']",ISO/TC 35,9599,"[20922,24006,8464]",[44649],"['en','fr']",6,"<p>ISO 3251:2003 specifies a method for determining the non-volatile-matter content by mass of paints, varnishes, binders for paints and varnishes, polymer dispersions and condensation resins such as phenolic resins (resols, novolak solutions, etc.).</p><p>The method is also applicable to formulated dispersions containing fillers, pigments and other auxiliaries (e.g. thickeners and film-forming agents). For the met

44649,IS,,ISO 3251:2008,"Paints, varnishes and plastics — Determination of non-volatile-matter content","Peintures, vernis et plastiques — Détermination de l'extrait sec",2008-01-31,4,"['83.080.01','87.040','87.060.20']",ISO/TC 35,9599,[30333],[73848],"['en','fr','ru']",7,"<p>ISO 3251:2008 specifies a method for determining the non-volatile-matter content by mass of paints, varnishes, binders for paints and varnishes, polymer dispersions and condensation resins such as phenolic resins (resols, novolak solutions, etc.).</p><p>The method is also applicable to formulated dispersions containing fillers, pigments and other auxiliaries (e.g. thickeners and film-forming agents). For the method to b

8465,IS,,ISO 3252:1982,Powder metallurgy — Vocabulary,Métallurgie des poudres — Vocabulaire,1982-05-01,2,"['77.160','01.040.77']",ISO/TC 119,9599,,[2016],"['en','fr']",21,

2016,IS,,ISO 3252:1996,Powder metallurgy — Vocabulary,Métallurgie des poudres — Vocabulaire,1996-01-25,3,"['77.160','01.040.77']",ISO/TC 119,9599,[8465],[26045],"['en','fr']",56,

27197,IS,Cor,ISO 3252:1996/Cor 1:1996,Powder metallurgy — Vocabulary — Technical Corrigendum 1,Métallurgie des poudres — Vocabulaire — Rectificatif technique 1,1996-10-10,3,"['77.160','01.040.77']",ISO/TC 119,9599,,[26045],"['en','fr']",2,

26045,IS,,ISO 3252:1999,Powder metallurgy — Vocabulary,Métallurgie des poudres — Vocabulaire,1999-12-16,4,"['01.040.77','77.160']",ISO/TC 119,9599,"[2016,27197]",[69828],"['en','fr']",59,

69828,IS,,ISO 3252:2019,Powder metallurgy — Vocabulary,Métallurgie des poudres — Vocabulaire,2019-07-31,5,"['77.160','01.040.77']",ISO/TC 119,9599,[26045],[83128],"['en','fr']",34,"<p>This document defines terms relating to powder metallurgy. Powder metallurgy is the branch of metallurgy which relates to the manufacture of metallic powders, or of articles made from such powders with or without the addition of non-metallic powders, by the application of forming and sintering processes.</p>"

8466,IS,,ISO 3253:1975,"Hose connections for equipment for welding, cutting and related processes","Raccords pour tuyaux souples pour appareils de soudage, coupage et techniques connexes",1975-05-01,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[28604],"['en','fr']",4,