Withdrawn and superseded ISO standards — page 95 of 246

39968,IS,,ISO 2910:2007,Cinematography — Screen luminance and chrominance for the projection of motion pictures,Cinématographie — Luminance et chrominance des écrans pour la projection de films,2007-01-24,3,['37.060.10'],ISO/TC 36,9599,[7950],[74446],['en'],5,"<p>ISO 2910:2007 specifies the screen luminance level and chrominance white point for theatrical projection of 70 mm, 35 mm and 16 mm motion-picture prints at a rate of 24 frames per second.</p><p>ISO 2910:2007 can also be applicable to the non-theatrical presentation of 70 mm, 35 mm and 16 mm motion-picture prints intended for projection at 24 frames per second.</p>"

7951,IS,,ISO 2911:1976,Sweetened condensed milk — Determination of sucrose content — Polarimetric method,Laits concentrés sucrés — Détermination de la teneur en saccharose — Méthode polarimétrique,1976-12-01,1,['67.100.10'],ISO/TC 34/SC 5,9599,,"[7952,40463]","['en','fr']",3,"<p>Is applicable to sweetened condensed milk of normal composition prepared from whole, partially skimmed or skimmed milk and sucrose only and containing no altered succrose. The principle consists in treating the sample with ammonia, neutralizing and clarifying by addition of zinc acetate and potassium hexacyanoferrate(II). This is following by filtration and determination of the optical rotation on part of the filtrat

7959,IS,,ISO 2917:1974,Meat and meat products — Measurement of pH (Reference method),Viandes et produits à base de viande — Mesurage du pH (Méthode de référence),1974-04-01,1,['67.120.10'],ISO/TC 34/SC 6,9599,,[24785],"['en','fr']",3,

7963,IS,,ISO 2919:1980,Sealed radioactive sources — Classification,Sources radioactives scellées — Classification,1980-05-01,1,['13.280'],ISO/TC 85,9599,,[2638],"['en','fr']",10,

2638,IS,,ISO 2919:1999,Radiation protection — Sealed radioactive sources — General requirements and classification,Radioprotection — Sources radioactives scellées — Prescriptions générales et classification,1999-02-18,2,['13.280'],ISO/TC 85/SC 2,9599,"[7963,6291]","[54441,41232]","['en','fr']",19,

7964,IS,,ISO 2920:1974,Whey cheese — Determination of dry matter content (Reference method),Fromage de sérum — Détermination de la teneur en matière sèche (Méthode de référence),1974-05-01,1,['67.100.30'],ISO/TC 34/SC 5,9599,,"[40464,7965]","['en','fr']",2,"<p>Specifies a method, the principle of which consists in desiccating a sample of whey cheese in a well ventilated and thermostaticalle controlled drying oven at a temperature of 88 +/- 2 agree Celsius.</p>"

7966,IS,,ISO 2921:1982,"Rubber, vulcanized — Determination of low temperature characteristics — Temperature-retraction procedure (TR test)",Caoutchouc vulcanisé — Détermination des caractéristiques à basse température — Méthode température-retrait (essai TR),1982-02-01,2,['83.060'],ISO/TC 45/SC 2,9599,,[23838],"['en','fr']",4,

23838,IS,,ISO 2921:1997,"Rubber, vulcanized — Determination of low-temperature characteristics — Temperature-retraction procedure (TR test)",Caoutchouc vulcanisé — Détermination des caractéristiques à basse température — Méthode température-retrait (essai TR),1997-04-10,3,['83.060'],ISO/TC 45/SC 2,9599,[7966],[39931],"['en','fr']",6,

39931,IS,,ISO 2921:2005,"Rubber, vulcanized — Determination of low-temperature characteristics — Temperature-retraction procedure (TR test)",Caoutchouc vulcanisé — Détermination des caractéristiques à basse température — Méthode température-retrait (essai TR),2005-10-04,4,['83.060'],ISO/TC 45/SC 2,9599,[23838],[53020],"['en','fr']",6,<p>ISO 2921:2005 specifies a method for the determination of the temperature-retraction characteristics of stretched vulcanized rubber.</p>

53020,IS,,ISO 2921:2011,"Rubber, vulcanized — Determination of low-temperature retraction (TR test)",Caoutchouc vulcanisé — Détermination du retrait à basse température (essai TR),2011-10-18,5,['83.060'],ISO/TC 45/SC 2,9599,[39931],[72779],"['en','fr','ru']",8,"<p>ISO 2921:2011 specifies a method for the determination of the temperature-retraction characteristics of stretched vulcanized rubber.</p><p>It does not cover thermoplastic rubbers, as many thermoplastic elastomers have a yield point in the range of 5 % to 20 % elongation. This fact might affect the result when carrying out temperature-retraction tests on thermoplastic rubbers, and the results obtained from such tests should be analy

7967,IS,,ISO 2922:1975,Acoustics — Measurement of noise emitted by vessels on inland water-ways and harbours,Acoustique — Mesurage du bruit émis par les bateaux de navigation intérieure et portuaire,1975-09-01,1,"['17.140.30','47.060']",ISO/TC 43/SC 1,9599,,[27307],"['en','fr']",4,

27307,IS,,ISO 2922:2000,Acoustics — Measurement of airborne sound emitted by vessels on inland waterways and harbours,Acoustique — Mesurage du bruit aérien émis par les bateaux de navigation intérieure et portuaire,2000-10-26,2,['17.140.30'],ISO/TC 43/SC 1,9599,[7967],[74023],"['en','fr']",10,

59762,IS,Amd,ISO 2922:2000/Amd 1:2013,Acoustics — Measurement of airborne sound emitted by vessels on inland waterways and harbours — Amendment 1,Acoustique — Mesurage du bruit aérien émis par les bateaux de navigation intérieure et portuaire — Amendement 1,2013-07-16,2,['17.140.30'],ISO/TC 43/SC 1,9599,,[74023],"['en','fr']",1,

7968,IS,,ISO 2923:1975,Acoustics — Measurement of noise on board vessels,Acoustique — Mesurage du bruit à bord des bateaux,1975-09-01,1,"['17.140.30','47.020.01']",ISO/TC 43,9599,,[1098],"['en','fr']",4,

7971,IS,,ISO 2926:1974,Aluminium oxide primarily used for the production of aluminium — Particle size analysis — Sieving method,Oxyde d'aluminium principalement utilisé pour la production de l'aluminium — Analyse granulométrique — Méthode par tamisage,1974-02-01,1,['71.100.10'],ISO/TC 226,9599,,"[41161,34452]","['en','fr']",2,"<p>Specifies a method for determining the mass distribution of the particle sizes of diameter 50 m and more. The procedure based on mechanical sieving of the crude sample, dried at 100 °C, through woven wire sieves in an atmosphere of relative humidity not more than 50 %. Weighing of each of the separate fractions. Verification, by means of a lens or microscope, of the

41161,IS,,ISO 2926:2005,Aluminium oxide used for the production of primary aluminium — Particle size analysis for the range 45 µm to 150 µm — Method using electroformed sieves,Oxyde d'aluminium utilisé pour la production d'aluminium primaire — Analyse granulométrique dans la gamme 45 µm à 150 µm — Méthode par emploi de tamis électroformés,2005-03-21,2,['71.100.10'],ISO/TC 226,9599,[7971],[52316],['en'],7,"<p>ISO 2926:2005 specifies a dry sieve method using electroformed sieves for determining the mass distribution of the particle sizes in aluminium oxide used for the production of primary aluminium.</p><p>ISO 2926:2005 is applicable to calcined aluminium oxide containing a maximum of 20 % ma

7973,IS,,ISO 2928:1975,Rubber hose for liquefied petroleum gases (LPG),Tuyaux en caoutchouc pour gaz de pétrole liquéfiés,1975-04-01,1,"['83.140.40','75.200']",ISO/TC 45,9599,,[7974],"['en','fr']",2,

7974,IS,,ISO 2928:1986,Rubber hoses and hose assemblies for liquefied petroleum gases (LPG) — Bulk transfer applications — Specification,Tuyaux et flexibles en caoutchouc pour gaz de pétrole liquéfiés (LPG) — Application au transfert de vrac — Spécifications,1986-07-03,2,"['83.140.40','75.200']",ISO/TC 45/SC 1,9599,[7973],"[35653,20162]","['en','fr']",2,"<p>Specifies the requirements for use with rail tank wagons or road tank vehicles. The hoses are intended to be filled with liquids in a range of temperature from -40 °C to +60 °C and with a maximum pressure of 2 MPa (20 bar). Construction, dimensions and tolerances and the physical requirements of finished hoses are given. Three tables cont

35653,IS,,ISO 2928:2003,"Rubber hoses and hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 25 bar (2,5 MPa) — Specification","Tuyaux et flexibles en caoutchouc pour gaz de pétrole liquéfié (GPL) en phase liquide ou gazeuse et le gaz naturel jusqu'à 25 bar (2,5 MPa) — Spécifications",2003-08-19,3,"['83.140.40','75.200']",ISO/TC 45/SC 1,9599,[7974],[77508],['en'],12,"<p>ISO 2928:2003 specifies requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas and designed for use at working pressures ranging from vacuum to a maximum of 25 bar (2,5 MP

61567,IS,,ISO 29281-1:2013,Intelligent transport systems — Communication access for land mobiles (CALM) — Non-IP networking — Part 1: Fast networking & transport layer protocol (FNTP),Systèmes intelligents de transport — Accès aux communications des services mobiles terrestres (CALM) — Réseautique non-IP — Partie 1: Réseautique rapide et protocole de la couche transport,2013-04-11,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,[45379],[70075],['en'],30,<p>ISO 29281-1:2013 specifies a protocol of the ITS-S networking and transport layer in support of efficient ad hoc single-hop communications with optional N-hop broadcast.</p>

65609,IS,Amd,ISO 29281-1:2013/Amd 1:2017,Intelligent transport systems — Communication access for land mobiles (CALM) — Non-IP networking — Part 1: Fast networking & transport layer protocol (FNTP) — Amendment 1,Systèmes intelligents de transport — Accès aux communications des services mobiles terrestres (CALM) — Réseautique non-IP — Partie 1: Réseautique rapide et protocole de la couche transport — Amendement 1,2017-04-05,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,,[70075],['en'],6,

61568,IS,,ISO 29281-2:2013,Intelligent transport systems — Communication access for land mobiles (CALM) — Non-IP networking — Part 2: Legacy system support,Systèmes intelligents de transport — Accès aux communications des services mobiles terrestres (CALM) — Réseautique non-IP — Partie 2: Support pour systèmes hérités,2013-04-11,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,[45379],[69636],['en'],24,"<p>ISO 29281-2:2013 specifies elements of communications for cooperative ITS which are not based on the Internet protocol.</p><p>The following architectures, procedures and protocols are specified:</p><p>-Support of communication interfaces (DSRC-CI) using ISO 15628;</p><p>-Support of ISO 15628

65610,IS,Amd,ISO 29281-2:2013/Amd 1:2014,Intelligent transport systems — Communication access for land mobiles (CALM) — Non-IP networking — Part 2: Legacy system support — Amendment 1,Systèmes intelligents de transport — Accès aux communications des services mobiles terrestres (CALM) — Réseautique non-IP — Partie 2: Support pour systèmes hérités — Amendement 1,2014-10-21,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,,[69636],['en'],2,

45379,IS,,ISO 29281:2011,Intelligent transport systems — Communications access for land mobiles (CALM) — Non-IP networking,Systèmes intelligents de transport — Accès aux communications des services mobiles terrestres (CALM) — Réseautique non-IP,2011-03-24,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,,"[61568,61567]",['en'],76,"<p>ISO 29281:2011 specifies FAST services, i.e. FAST networking &amp; transport layer protocols for single-hop communications, N-hop broadcast communications, ITS-MUX, and ITS station-internal forwarding; FAST service for 15628 CI (DSRC CI) support; FAST service for 15628 application support; and the related support of the MN-SAP and MF-SAP.</p>"

7975,IS,,ISO 2929:1975,Rubber hose for fuel truck delivery,Tuyaux en caoutchouc pour camions-citernes,1975-05-01,1,"['83.140.40','75.200']",ISO/TC 45/SC 1,9599,,[7976],"['en','fr']",3,

7976,IS,,ISO 2929:1991,Rubber hoses for bulk fuel truck delivery — Specification,Tuyaux en caoutchouc pour livraison en vrac d'hydrocarbures liquides par camions-citernes — Spécifications,1991-06-27,2,"['83.140.40','75.200']",ISO/TC 45/SC 1,9599,[7975],[33671],"['en','fr']",3,

33671,IS,,ISO 2929:2002,Rubber hoses and hose assemblies for bulk fuel delivery by truck — Specification,Tuyaux en caoutchouc et assemblages de tuyaux pour livraison en vrac d'hydrocarbures liquides par camions-citernes — Spécifications,2002-10-17,3,"['83.140.40','75.200']",ISO/TC 45/SC 1,9599,[7976],[63805],['en'],14,"<p>ISO 2929:2002 specifies the requirements for two groups of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 10 bar (1,0 MPa).</p><p>Both groups of hoses are designed for:</p><ol><li>use with hydrocarbon fuels having an aromatic-hydrocarbon content not exceeding 50 % by volume and containing up t

63805,IS,,ISO 2929:2014,Rubber hoses and hose assemblies for bulk fuel delivery by truck — Specification,Tuyaux en caoutchouc et assemblages de tuyaux pour livraison en vrac d'hydrocarbures liquides par camions-citernes — Spécifications,2014-02-21,4,"['83.140.40','75.200']",ISO/TC 45/SC 1,9599,[33671],"[80477,81747]",['en'],15,"<p>ISO 2929:2014 specifies the requirements for two groups of rubber hoses and rubber hose assemblies for loading and discharge of liquid hydrocarbon fuels with a maximum working pressure of 10 bar (1,0 MPa).</p><p>Both groups of hoses are designed for:</p><p>a) use with hydrocarbon fuels having an aromatic-hydrocarbon content not exceeding 50 % by volume and conta

4217,IS,,ISO 293:1974,Plastics — Compression moulding test specimens of thermoplastic materials,Matières plastiques — Moulage par compression des éprouvettes en matières thermoplastiques,1974-08-01,1,['83.080.20'],ISO/TC 61,9599,,[4218],"['en','fr']",4,

4218,IS,,ISO 293:1986,Plastics — Compression moulding test specimens of thermoplastic materials,Plastiques — Moulage par compression des éprouvettes en matières thermoplastiques,1986-10-09,2,['83.080.20'],ISO/TC 61/SC 9,9599,[4217],"[39885,28289]","['en','fr']",4,"<p>Specifies the general principles and the procedures to be followed with thermoplastics in the preparation of specimens, which are homogeneous and isotropic and from which test specimens may be machined or stamped. In order to obtain mouldings in a reproducible state, the main steps of the procedure, including four different cooling methods, are standardized. Two alternative kinds of moulds, flash moulds and positive moulds, are

39885,IS,,ISO 293:2004,Plastics — Compression moulding of test specimens of thermoplastic materials,Plastiques — Moulage par compression des éprouvettes en matières thermoplastiques,2004-05-11,3,['83.080.20'],ISO/TC 61/SC 9,9599,[4218],"[50604,83779]","['en','fr']",6,"<p>ISO 293:2004 specifies the general principles and the procedures to be followed with thermoplastics in the preparation of compression-moulded test specimens, and sheets from which test specimens may be machined or stamped.</p>"

7977,IS,,ISO 2930:1981,"Rubber, raw natural — Determination of plasticity retention index (PRI)",Caoutchouc naturel brut — Détermination de l'indice de rétention de plasticité (PRI),1981-12-01,2,['83.040.10'],ISO/TC 45/SC 3,9599,,[20183],"['en','fr']",2,

20183,IS,,ISO 2930:1995,"Rubber, raw natural — Determination of plasticity retention index (PRI)",Caoutchouc naturel brut — Détermination de l'indice de rétention de plasticité (PRI),1995-06-08,3,['83.040.10'],ISO/TC 45/SC 3,9599,[7977],[53002],"['en','fr']",3,<p>Cancels and replaces the second edition (1981). Specifies a method for determining the plasticity retention index (PRI) of raw natural rubber. The PRI is a measure of the resistance of raw natural rubber to thermal oxidation. A high resistance to thermal oxidation is shown as a high value of the index.</p>

43712,IS,Amd,ISO 2930:1995/Amd 1:2008,"Rubber, raw natural — Determination of plasticity retention index (PRI) — Amendment 1",Caoutchouc naturel brut — Détermination de l'indice de rétention de plasticité (PRI) — Amendement 1,2008-09-15,3,['83.040.10'],ISO/TC 45/SC 3,9599,,[53002],"['en','fr']",3,

53002,IS,,ISO 2930:2009,"Rubber, raw natural — Determination of plasticity retention index (PRI)",Caoutchouc naturel brut — Détermination de l'indice de rétention de plasticité (PRI),2009-11-30,4,['83.040.10'],ISO/TC 45/SC 3,9599,"[20183,43712]",[68068],"['en','fr','ru']",7,<p>ISO 2930:2009 specifies a method for determining the plasticity retention index (PRI) of raw natural rubber.</p><p>The PRI is a measure of the resistance of raw natural rubber to thermal oxidation. A high resistance to thermal oxidation is shown as a high value of the index.</p>

68068,IS,,ISO 2930:2017,"Rubber, raw natural — Determination of plasticity retention index (PRI)",Caoutchouc naturel brut — Détermination de l'indice de rétention de plasticité (PRI),2017-08-30,5,['83.040.10'],ISO/TC 45/SC 3,9599,[53002],[86503],"['en','fr']",9,<p>ISO 2930:2017 specifies a method for determining the plasticity retention index (PRI) of raw natural rubber.</p><p>The PRI is a measure of the resistance of raw natural rubber to thermal oxidation. A high resistance to thermal oxidation is shown as a high value of the index. PRI is not an absolute value and cannot give an absolute classification of plasticity number of different natural rubber after oxidation.</p>

45399,IS,,ISO 29301:2010,Microbeam analysis — Analytical transmission electron microscopy — Methods for calibrating image magnification by using reference materials having periodic structures,Analyse par microfaisceaux — Microscopie électronique en transmission analytique — Méthodes d'étalonnage du grandissement d'image au moyen de matériaux de référence de structures périodiques,2010-05-17,1,['37.020'],ISO/TC 202/SC 3,9599,,[70360],['en'],40,"<p>ISO 29301:2010 specifies a calibration procedure applicable to images recorded over a wide magnification range in a transmission electron microscope (TEM). The reference materials used for calibration possess a periodic structure, such as a diffract

70360,IS,,ISO 29301:2017,Microbeam analysis — Analytical electron microscopy — Methods for calibrating image magnification by using reference materials with periodic structures,Analyse par microfaisceaux — Microscopie électronique analytique — Méthodes d'étalonnage du grandissement d'image au moyen de matériaux de référence de structures périodiques,2017-12-06,2,['37.020'],ISO/TC 202/SC 3,9599,[45399],[86942],['en'],44,"<p>ISO 29301:2017 specifies a calibration procedure applicable to images recorded over a wide magnification range in a transmission electron microscope (TEM). The reference materials used for calibration possess a periodic structure, such as a diffraction grating replica, a s

7978,IS,,ISO 2931:1983,Anodizing of aluminium and its alloys — Assessment of quality of sealed anodic oxide coatings by measurement of admittance or impedance,Anodisation de l'aluminium et de ses alliages — Évaluation de la qualité des couches anodiques colmatées par mesurage de l'admittance ou de l'impédance,1983-07-01,2,['25.220.20'],ISO/TC 79/SC 2,9599,,"[51488,1357]","['en','fr']",3,"<p>This test is intended to give a quick, non-destructive assessment of the quality of sealed anodic oxide coatings and is therefore very suitable as a routine production control. It is also suitable for use as an acceptance test.</p>"

51488,IS,,ISO 2931:2010,Anodizing of aluminium and its alloys — Assessment of quality of sealed anodic oxidation coatings by measurement of admittance,Anodisation de l'aluminium et de ses alliages — Évaluation de la qualité des couches anodiques colmatées par mesurage de l'admittance,2010-06-24,3,['25.220.20'],ISO/TC 79/SC 2,9599,[7978],[70155],"['en','fr']",5,"<p>ISO 2931:2010 specifies a method for assessing the quality of sealed anodic oxidation coatings on aluminium and its alloys by measurement of the admittance.</p><p>The method is applicable to anodic oxidation coatings sealed in an aqueous medium.</p><p>The method is suitable for use as a production-control test and as an acceptance

7980,IS,,ISO 2933:1974,Bonded abrasive products — Grinding wheel dimensions (Part 3),Produits abrasifs agglomérés — Dimensions des meules (Troisième partie),1974-02-01,1,['25.100.70'],ISO/TC 29/SC 5,9599,,"[2724,4713,4707,21897,4714,21898,4709,21899,4710,20536,2736,21900,4711,21632,4712,2715]","['en','fr']",6,

7983,IS,,ISO 2936:1983,Assembly tools for screws and nuts — Hexagon socket screw keys — Metric series,Outils de manoeuvre pour vis et écrous — Clés mâles coudées pour vis à six pans creux — Série métrique,1983-12-01,3,['25.140.30'],ISO/TC 29/SC 10,9599,,[21908],"['en','fr']",3,

21908,IS,,ISO 2936:1995,Assembly tools for screws and nuts — Hexagon socket screw keys,Outils de manoeuvre pour vis et écrous — Clés mâles coudées pour vis à six pans creux,1995-06-22,4,['25.140.01'],ISO/TC 29/SC 10,9599,[7983],[29090],"['en','fr']",5,

29090,IS,,ISO 2936:2001,Assembly tools for screws and nuts — Hexagon socket screw keys,Outils de manoeuvre pour vis et écrous — Clés mâles coudées pour vis à six pans creux,2001-03-22,5,['25.140.30'],ISO/TC 29/SC 10,9599,[21908],[60231],"['en','fr']",8,

50574,IS,Cor,ISO 2936:2001/Cor 1:2007,Assembly tools for screws and nuts — Hexagon socket screw keys — Technical Corrigendum 1,Outils de manoeuvre pour vis et écrous — Clés mâles coudées pour vis à six pans creux — Rectificatif technique 1,2007-10-30,5,['25.140.30'],ISO/TC 29/SC 10,9599,,[60231],['fr'],,

53787,IS,,ISO 29383:2010,Terminology policies — Development and implementation,Politiques terminologiques — Élaboration et mise en oeuvre,2010-07-09,1,['01.020'],ISO/TC 37/SC 1,9599,,[71971],"['en','fr']",16,"<p>ISO 29383:2010 provides policy makers in governments, administration, non-profit and commercial organizations with guidelines and a methodology for the development and implementation of a comprehensive policy or strategy concerning the planning and management of terminology.</p><p>ISO 29383:2010 defines key concepts and describes scenarios and environments which may require different kinds of terminology policies. It also places terminology policies in the broader context of institut

7986,IS,,ISO 2939:1975,Cinematography — Picture image area and photographic sound record on 35 mm motion-picture release prints — Positions and dimensions,Cinématographie — Champ d'image et piste sonore photographique sur les copies d'exploitation de 35 mm — Emplacements et dimensions,1975-07-01,1,['37.060.20'],ISO/TC 36,9599,,[7987],"['en','fr']",2,

7987,IS,,ISO 2939:1986,Cinematography — Picture image area and photographic sound record on 35 mm motion-picture release prints — Position and dimensions,Cinématographie — Champ d'image et piste sonore photographique sur les copies d'exploitation de 35 mm — Position et dimensions,1986-10-23,2,['37.060.20'],ISO/TC 36,9599,"[7986,3611]","[35511,28292]","['en','fr']",3,

35511,IS,,ISO 2939:2002,Cinematography — Picture image area on 35 mm motion-picture release prints — Position and dimensions,Cinématographie — Champ d'image sur les copies d'exploitation de 35 mm — Position et dimensions,2002-10-17,3,['37.060.20'],ISO/TC 36,9599,[7987],[52811],['en'],3,"<p>ISO 2939 :2002 specifies the position and dimensions of picture image areas on 35 mm motion-picture release prints, which have been assigned for optical projection based on ISO 2907 or transmitted by television based on ISO 1223.</p>"

25185,IS,,ISO 294-1:1996,"Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens","Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 1: Principes généraux, et moulage des éprouvettes à usages multiples et des barreaux",1996-12-26,1,['83.080.20'],ISO/TC 61/SC 9,9599,[4220],"[45070,67036]","['en','fr']",14,<p>Contains the general principles to be followed for the preparation of injection moulding test specimens of thermoplastics and gives details of mould design for preparing multipurpose test specimens as specified in ISO 3167 and tensile bars. Replaces

33339,IS,Amd,ISO 294-1:1996/Amd 1:2001,"Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens — Amendment 1","Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 1: Principes généraux, et moulage des éprouvettes à usages multiples et des barreaux — Amendement 1",2001-01-25,1,['83.080.20'],ISO/TC 61/SC 9,9599,,"[45070,67036]","['en','fr']",1,

36267,IS,Amd,ISO 294-1:1996/Amd 2:2005,"Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens — Amendment 2: Methods of determining the hold pressure and hold time","Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 1: Principes généraux, et moulage des éprouvettes à usages multiples et des barreaux — Amendement 2: Méthodes pour mesurer la pression de maintien et la durée de maintien",2005-09-05,1,['83.080.20'],ISO/TC 61/SC 9,9599,,"[45070,67036]","['en','fr']",6,

4219,IS,,ISO 294:1975,Plastics — Injection moulding test specimens of thermoplastic materials,Matières plastiques — Moulage par injection des éprouvettes en matières thermoplastiques,1975-05-01,1,['83.080.20'],ISO/TC 61,9599,,[4220],"['en','fr']",3,

4220,IS,,ISO 294:1995,Plastics — Injection moulding of test specimens of thermoplastic materials,Plastiques — Moulage par injection des éprouvettes en matériaux thermoplastiques,1995-02-09,2,['83.080.20'],ISO/TC 61/SC 9,9599,[4219],"[25187,25188,25185,25186]","['en','fr']",10,

25186,IS,,ISO 294-2:1996,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 2: Barreaux de traction de petites dimensions,1996-12-26,1,['83.080.20'],ISO/TC 61/SC 9,9599,[4220],"[70412,45071]","['en','fr']",3,"<p>Specifies a four-cavity mould, the type C, for the injection moulding of small tensile bars measuring &gt;= 60 mm × 10 mm × 3 mm. Replaces the second edition of ISO 294.</p>"

40061,IS,Amd,ISO 294-2:1996/Amd 1:2004,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars — Amendment 1,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 2: Barreaux de traction de petites dimensions — Amendement 1,2004-05-07,1,['83.080.20'],ISO/TC 61/SC 9,9599,,"[70412,45071]","['en','fr']",1,

25187,IS,,ISO 294-3:1996,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 3: Plaques de petites dimensions,1996-12-26,1,['83.080.20'],ISO/TC 61/SC 9,9599,"[7511,4220]",[32205],"['en','fr']",8,"<p>Specifies two two-cavity moulds, the type D1 and D2, for the injection moulding of small plates measuring 60 mm × 60 mm with a preferred thickness of 1 mm (type D1) or 2 mm (type D2) which can be used for a variety of tests. Replaces the second edition of ISO 294.</p>"

32205,IS,,ISO 294-3:2002,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 3: Plaques de petites dimensions,2002-06-13,2,['83.080.20'],ISO/TC 61/SC 9,9599,[25187],"[50603,76649]","['en','fr']",8,"<p>This part of ISO 294 specifies two two-cavity moulds, the type D1 and D2 ISO moulds, for the injection moulding of small plates measuring 60 mm × 60 mm with a preferred thickness of 1 mm (type D1) or 2 mm (type D2), which can be used for a variety of tests. The moulds may additionally be fitted with inserts for studying the effects of weld lines on the mechanic

34837,IS,Amd,ISO 294-3:2002/Amd 1:2006,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates — Amendment 1,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 3: Plaques de petites dimensions — Amendement 1,2006-02-16,2,['83.080.20'],ISO/TC 61/SC 9,9599,,"[50603,76649]","['en','fr']",1,

25188,IS,,ISO 294-4:1997,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination of moulding shrinkage,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 4: Détermination du retrait au moulage,1997-04-17,1,['83.080.20'],ISO/TC 61/SC 9,9599,[4220],[31273],"['en','fr']",8,

31273,IS,,ISO 294-4:2001,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination of moulding shrinkage,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 4: Détermination du retrait au moulage,2001-12-20,2,['83.080.20'],ISO/TC 61/SC 9,9599,[25188],"[70413,45072]","['en','fr']",9,

50616,IS,Cor,ISO 294-4:2001/Cor 1:2007,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4: Determination of moulding shrinkage — Technical Corrigendum 1,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 4: Détermination du retrait au moulage — Rectificatif technique 1,2007-11-19,2,['83.080.20'],ISO/TC 61/SC 9,9599,,[70413],"['en','fr']",2,

27209,IS,,ISO 294-5:2001,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 5: Préparation d'éprouvettes normalisées pour déterminer l'anisotropie,2001-12-13,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[45073],"['en','fr']",7,

36269,IS,Amd,ISO 294-5:2001/Amd 1:2004,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy — Amendment 1,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 5: Préparation d'éprouvettes normalisées pour déterminer l'anisotropie — Amendement 1,2004-05-07,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[45073],"['en','fr']",1,

38365,IS,Cor,ISO 294-5:2001/Cor 1:2003,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy — Technical Corrigendum 1,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 5: Préparation d'éprouvettes normalisées pour déterminer l'anisotropie — Rectificatif technique 1,2003-04-01,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[45073],"['en','fr']",1,

45073,IS,,ISO 294-5:2011,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 5: Préparation d'éprouvettes normalisées pour déterminer l'anisotropie,2011-04-07,2,['83.080.20'],ISO/TC 61/SC 9,9599,"[27209,36269,38365]",[65481],"['en','fr']",7,"<p>ISO 294-5:2011 specifies a two-cavity mould (designated the type F ISO mould) for the injection moulding of 80 mm x 90 mm plates with a preferred thickness of 2 mm for single-point data acquisition because 2 mm has been found to provide the maximum anisotropic properti

65481,IS,,ISO 294-5:2017,Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy,Plastiques — Moulage par injection des éprouvettes de matériaux thermoplastiques — Partie 5: Préparation d'éprouvettes normalisées pour déterminer l'anisotropie,2017-11-09,3,['83.080.20'],ISO/TC 61/SC 9,9599,[45073],[85835],"['en','fr']",7,"<p>ISO 294-5:2017 specifies a mould (designated the type F ISO mould) for the injection moulding of plates with a preferred size of 80 mm × 120 mm and a minimum size of 80 mm × ≥90 mm and with a preferred thickness of 2 mm for single-point and multi-point data acquisition. It has been

60906,IS,,ISO 29400:2015,Ships and marine technology — Offshore wind energy — Port and marine operations,Navires et technologie maritime — Énergie éolienne offshore — Opérations portuaires et maritimes,2015-05-08,1,['47.020.50'],ISO/TC 8,9599,,[71100],['en'],203,"<p>ISO 29400:2015 provides comprehensive requirements and guidance for the planning and engineering of port and marine operations, encompassing all documents and works related to such port and marine operations, e.g. the design and analysis of the components, systems, equipment and procedures required to perform port and marine operations, as well as the methods or procedures developed to carry them out safely.</p><p>ISO 29400:2015

7990,IS,,ISO 2941:1974,Hydraulic fluid power — Filter elements — Verification of collapse/burst resistance,Transmissions hydrauliques — Éléments filtrants — Vérification de la résistance à l'écrasement ou à l'éclatement,1974-03-01,1,['23.100.60'],ISO/TC 131/SC 6,9599,,"[41062,31113]","['en','fr']",2,"<p>Specifies a method for verifying the collapse/burst rating of a filter element, i. e. the capability of the filter to withstand a designated differential pressure at the normal (intended direction) of flow. The figure shows a sketch of a typical collapse/burst test stand.</p>"

7991,IS,,ISO 2942:1974,Hydraulic fluid power — Filter elements — Determination of fabrication integrity,Transmissions hydrauliques — Éléments filtrants — Détermination de la conformité de fabrication,1974-03-01,1,['23.100.60'],ISO/TC 131,9599,,"[7992,21325]","['en','fr']",2,

7992,IS,,ISO 2942:1985,Hydraulic fluid power — Filter elements — Verification of fabrication integrity,Transmissions hydrauliques — Éléments filtrants — Vérification de la conformité de fabrication,1985-01-31,2,['23.100.60'],ISO/TC 131/SC 6,9599,[7991],[21325],['en'],2,

21325,IS,,ISO 2942:1994,Hydraulic fluid power — Filter elements — Verification of fabrication integrity and determination of the first bubble point,Transmissions hydrauliques — Éléments filtrants — Vérification de la conformité de fabrication et détermination du point de première bulle,1994-09-15,3,['23.100.60'],ISO/TC 131/SC 6,9599,"[7991,7992]",[34692],"['en','fr']",4,<p>Cancels and replaces the second edition (1985). Specifies a bubble-point test method applicable to filter elements to be used in hydraulic fluid power systems. It can be used either to verify the fabrication integrity of a filter element or to permit the localization of the largest pore of the filtering medium by determini

34692,IS,,ISO 2942:2004,Hydraulic fluid power — Filter elements — Verification of fabrication integrity and determination of the first bubble point,Transmissions hydrauliques — Éléments filtrants — Vérification de la conformité de fabrication et détermination du point de première bulle,2004-09-01,4,['23.100.60'],ISO/TC 131/SC 6,9599,[21325],[68005],"['en','fr']",7,<p>ISO 2942:2004 specifies a bubble-point test method applicable to filter elements used in hydraulic fluid power systems. It can be used either to verify the fabrication integrity of a filter element (by checking the absence of bubbles) or to permit the localization of the largest pore of the filter element by determining the firs

7993,IS,,ISO 2943:1974,Hydraulic fluid power — Filter elements — Verification of material compatibility with fluids,Transmissions hydrauliques — Éléments filtrants — Vérification de la compatibilité des matériaux avec les fluides,1974-03-01,1,['23.100.60'],ISO/TC 131/SC 8,9599,,[26832],"['en','fr']",2,

7994,IS,,ISO 2944:1974,Fluid power systems and components — Nominal pressures,Transmissions hydrauliques et pneumatiques — Gamme de pressions nominales,1974-07-01,1,['23.100.01'],ISO/TC 131,9599,,[7995],"['en','fr']",1,

51291,IS,,ISO 29461-1:2013,Air intake filter systems for rotary machinery — Test methods — Part 1: Static filter elements,Systèmes de filtration d'air d'admission pour machines tournantes — Méthodes d'essai — Partie 1: Éléments filtrants pour filtres statiques,2013-04-03,1,['29.160.99'],ISO/TC 142,9599,,"[76920,70135]","['en','fr']",66,"<p>ISO 29461 specifies methods and procedures for determining the performance of particulate air filters used in air intake filter systems for rotary machinery such as stationary gas turbines, compressors and other stationary internal combustion engines. It applies to air filters having an initial particle efficiency up to 99,9 % with respect to 0,4 µm partic

45483,IS,,ISO 29462:2013,Field testing of general ventilation filtration devices and systems for in situ removal efficiency by particle size and resistance to airflow,Essais in situ de filtres et systèmes de ventilation générale pour la mesure de l'efficacité en fonction de la taille des particules et de la perte de charge,2013-03-13,1,['91.140.30'],ISO/TC 142,9599,,[79549],"['en','fr']",45,"<p>ISO 29462:2013 describes a procedure for measuring the performance of general ventilation air cleaning devices in their end use installed configuration. The performance measurements include removal efficiency by particle size and the resistance to airflow. The procedures for test include the definitio

51835,IS,,ISO 29463-1:2011,"High-efficiency filters and filter media for removing particles in air — Part 1: Classification, performance testing and marking","Filtres à haut rendement et filtres pour l'élimination des particules dans l'air — Partie 1: Classification, essais de performance et marquage",2011-10-07,1,['91.140.30'],ISO/TC 142,9599,,[67816],['en'],16,"<p>ISO 29463-1:2011 establishes a classification of filters based on their performance, as determined in accordance with ISO 29463-3, ISO 29463-4 and ISO 29463-5. It also provides an overview of the test procedures, and specifies general requirements for assessing and marking the filters, as well as for documenting the test results.

67816,IS,,ISO 29463-1:2017,"High efficiency filters and filter media for removing particles from air — Part 1: Classification, performance, testing and marking","Filtres et media à très haute efficacité pour la rétention particulaire — Partie 1: Classification, essais de performance et marquage",2017-10-04,2,['91.140.30'],ISO/TC 142,9599,[51835],[84367],['en'],16,"<p>ISO 29463-1 establishes a classification of filters based on their performance, as determined in accordance with ISO 29463‑3, ISO 29463‑4 and ISO 29463‑5. It also provides an overview of the test procedures, and specifies general requirements for assessing and marking the filters, as well as for documenting the test results. It

51839,IS,,ISO 29463-5:2011,High-efficiency filters and filter media for removing particles in air — Part 5: Test method for filter elements,Filtres à haut rendement et filtres pour l'élimination des particules dans l'air — Partie 5: Méthode d'essai des éléments filtrants,2011-10-07,1,['91.140.30'],ISO/TC 142,9599,,[77740],"['en','fr']",23,"<p>ISO 29463-5:2011 specifies the reference test procedure for determining the efficiency of filters at their most penetrating particle size (MPPS). ISO 29463-5:2011 also gives guidelines for the testing and classification for filters with an MPPS of less than 0,1 μm and filters using media with (charged) synthetic fibres. ISO 29463-5:2011 is intended for

45485,IS,,ISO 29464:2011,Cleaning equipment for air and other gases — Terminology,Séparateurs aérauliques — Terminologie,2011-08-25,1,"['91.140.30','01.040.91']",ISO/TC 142,9599,[9093],[62766],['en'],25,"<p>ISO 29464:2011 establishes a terminology for the air filtration industry and comprises terms and definitions together with, in some cases, symbols and units.</p><p>ISO 29464:2011 is applicable to both particulate and gas phase air filters and cleaners used for the general ventilation of inhabited enclosed spaces. Air inlet filters for static or seaborne rotary machines are included.</p><p>ISO 29464:2011 does not apply to cabin filters for road vehicles or air inlet filters for mobile inte

62766,IS,,ISO 29464:2017,Cleaning of air and other gases — Terminology,Épuration de l'air et autres gaz— Terminologie,2017-08-28,2,"['91.140.30','01.040.91']",ISO/TC 142,9599,[45485],[83049],"['en','fr']",34,<p>ISO 29464:2017 establishes a terminology for the air filtration industry and comprises terms and definitions only.</p><p>ISO 29464:2017 is applicable to particulate and gas phase air filters and air cleaners used for the general ventilation of inhabited enclosed spaces. It is also applicable to air inlet filters for static or seaborne rotary machines and UV-C germicidal devices.</p><p>It is not applicable to cabin filters for road vehicles or air inlet filters for mobile internal comb

45486,IS,,ISO 29465:2008,Thermal insulating products for building applications — Determination of length and width,Produits isolants thermiques destinés aux applications du bâtiment — Détermination de la longueur et de la largeur,2008-10-29,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[77887],['en'],4,<p>ISO 29465:2008 specifies the equipment and procedures for determining the length and width of full‑size products. It is applicable to thermal insulating products.</p>

45487,IS,,ISO 29466:2008,Thermal insulating products for building applications — Determination of thickness,Produits isolants thermiques destinés aux applications du bâtiment — Détermination de l'épaisseur,2008-10-29,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[77890],['en'],9,<p>ISO 29466:2008 specifies the equipment and procedures for determining the thickness of full‑size products. It is applicable to thermal insulating products.</p>

45489,IS,,ISO 29468:2008,Thermal insulating products for building applications — Determination of flatness,Produits isolants thermiques destinés aux applications du bâtiment — Détermination de la planéité,2008-10-30,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[77891],['en'],4,<p>ISO 29468:2008 specifies the equipment and procedures for determining the deviation from flatness for full-size products. It is applicable to thermal insulating products.</p>

45490,IS,,ISO 29469:2008,Thermal insulating products for building applications — Determination of compression behaviour,Produits isolants thermiques destinés aux applications du bâtiment — Détermination du comportement en compression,2008-10-30,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[78393],['en'],10,<p>ISO 29469:2008 specifies the equipment and procedures for determining the compression behaviour of specimens. It is applicable to thermal insulating products and can be used to determine the compressive stress in compressive creep tests and for applications in which insulation products are exposed only to short‑term loads.</p><p>ISO 29469:2008 can be used for quality control purposes and can a

45491,IS,,ISO 29470:2008,Thermal insulating products for building applications — Determination of the apparent density,Produits isolants thermiques destinés aux applications du bâtiment — Détermination de la masse volumique apparente,2008-09-08,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[69717],['en'],4,<p>ISO 29470:2008 specifies the equipment and procedures for determining the apparent overall density and the apparent core density under reference conditions. It is applicable to full-size thermal insulating products and test specimens. This International Standard can also be applied to the individual layers of multi-layered products.</p>

45501,IS,,ISO 29481-1:2010,Building information modelling — Information delivery manual — Part 1: Methodology and format,Modèles des informations de la construction — Contrat d'interchange — Partie 1: Méthodologie et format,2010-04-30,1,['91.010.01'],ISO/TC 59/SC 13,9599,,[60553],['en'],34,"<p>ISO 29481-1:2010 specifies a methodology and format for the development of an information delivery manual (IDM).</p><p>ISO 29481-1:2010 specifies a methodology that unites the flow of construction processes with the specification of the information required by this flow, a form in which the information should be specified, and an appropriate way to map and describe the information processes within a co

60553,IS,,ISO 29481-1:2016,Building information models — Information delivery manual — Part 1: Methodology and format,Modèles des informations de la construction — Protocole d’échange d’informations — Partie 1: Méthodologie et format,2016-04-26,2,"['35.240.67','91.010.01']",ISO/TC 59/SC 13,9599,[45501],[88515],"['en','fr']",29,"<p>ISO 29481-1:2016 specifies</p><p>- a methodology that links the business processes undertaken during the construction of built facilities with the specification of information that is required by these processes, and</p><p>- a way to map and describe the information processes across the life cycle of construction works.</p><p>ISO 29481-1:2016 is intended

55691,IS,,ISO 29481-2:2012,Building information models — Information delivery manual — Part 2: Interaction framework,Modèles des informations de la construction — Protocole d’échange d’informations — Partie 2: Cadre d'interaction,2012-12-12,1,"['35.240.67','91.010.01']",ISO/TC 59/SC 13,9599,,[88516],"['en','fr']",74,"<p>ISO 29481-2:2012 specifies a methodology and format for describing ?coordination acts' between actors in a building construction project during all life cycle stages.</p><p>It therefore specifies</p><ul><li>a methodology that describes an interaction framework,</li><li>an appropriate way to map responsibilities and interactions that provides a process context for information

4221,IS,,ISO 295:1974,Plastics — Compression moulding test specimens of thermosetting materials,Matières plastiques — Moulage par compression des éprouvettes en matières thermodurcissables,1974-12-01,1,['83.080.10'],ISO/TC 61/SC 12,9599,,[4222],"['en','fr']",5,

4222,IS,,ISO 295:1991,Plastics — Compression moulding of test specimens of thermosetting materials,Plastiques — Moulage par compression des éprouvettes en matières thermodurcissables,1991-11-14,2,['83.080.10'],ISO/TC 61/SC 12,9599,[4221],[28180],"['en','fr']",7,<p>Specifies the general principles and the procedures for the preparation of test specimens and for the establishment of comparable test reports from different testing organizations. This second edition cancels and replaces the first edition (1974).</p>

7997,IS,,ISO 2950:1974,Brown coals and lignites — Classification by types on the basis of total moisture content and tar yield,"Charbons bruns et lignites — Classification en types, d'après la teneur en humidité totale et le rendement en goudron",1974-02-01,1,['73.040'],ISO/TC 27/SC 5,9599,,[90230],"['en','fr']",2,"<p>Brown coals are classified in this International Standard according to the following properties: total moisture content calculated on the ash-free basis; tar hiels calculated on the dry, ash-free basis. In tables class numbers, group number and code numbers of brown coal types are given.</p>"

7998,IS,,ISO 2951:1974,Vulcanized rubber — Determination of insulation resistance,Élastomères vulcanisés — Détermination de la résistance d'isolement,1974-11-01,1,['83.060'],ISO/TC 45/SC 2,9599,,"[7999,55605]","['en','fr']",5,"<p>Specifies an empirical method that gives a value for insulation resistance which includes, without discrimination, both volume and surface resistance. This value can be used for the comparison of the quality of different insulation vulcanized rubbers. The methods are particularly useful for rapidly determining values which will give a general indication of quality when great accuracy is not required.</p>"

55605,IS,,ISO 2951:2012,"Rubber, vulcanized or thermoplastic — Determination of insulation resistance",Caoutchouc vulcanisé ou thermoplastique — Détermination de la résistance d'isolement,2012-05-21,2,['83.060'],ISO/TC 45/SC 2,9599,[7998],[74940],['en'],8,

8000,IS,,ISO 2953:1975,Balancing machines — Description and evaluation,"Machines à équilibrer — Description, caractéristiques et possibilités",1975-06-01,1,['21.120.40'],ISO/TC 108,9599,,[8001],"['en','fr']",22,

8001,IS,,ISO 2953:1985,Balancing machines — Description and evaluation,"Machines à équilibrer — Description, caractéristiques et possibilités",1985-10-31,2,['21.120.40'],ISO/TC 108,9599,[8000],[1733],"['en','fr']",34,

1733,IS,,ISO 2953:1999,Mechanical vibration — Balancing machines — Description and evaluation,Vibrations mécaniques — Machines à équilibrer — Description et évaluation,1999-04-22,3,['21.120.40'],ISO/TC 108/SC 2,9599,[8001],[56562],['en'],55,

8003,IS,,ISO 2954:1975,Mechanical vibration of rotating and reciprocating machinery — Requirements for instruments for measuring vibration severity,Vibrations mécaniques des machines tournantes ou alternatives — Spécifications des appareils de mesurage de l'intensité vibratoire,1975-07-01,1,['17.160'],ISO/TC 108,9599,,"[45727,21835]","['en','fr']",6,<p>States the requirements for measuring devices if inaccuracies of measurement are not to exceed a specified value. Devices covered give direct indication or recording of root-mean-square vibration velocity.</p>

45546,IS,,ISO 29541:2010,"Solid mineral fuels — Determination of total carbon, hydrogen and nitrogen content — Instrumental method","Combustibles minéraux solides — Dosage du carbone, de l'hydrogène et de l'azote totaux — Méthode instrumentale",2010-09-29,1,"['73.040','75.160.10']",ISO/TC 27/SC 5,9599,[35302],[86983],['en'],10,"<p>ISO 29541:2010 specifies a method for the determination of total carbon, hydrogen and nitrogen in coal and coke by instrumental methods.</p>"