Withdrawn and superseded ISO standards — page 78 of 246

35971,IS,,ISO 21690:2006,Glass in building — Glass blocks — Specification and test methods,Verre dans la construction — Briques de verre — Spécification et méthodes d'essai,2006-06-22,1,['81.040.20'],ISO/TC 160,9599,,[75042],"['en','fr']",10,"<p>ISO 21690:2006 specifies requirements for the properties of glass blocks used for the construction of non-load-bearing walls and horizontally spanning panels. ISO 21690:2006 also specifies test methods used to verify these properties for square, rectangular and circular glass blocks.</p>"

4089,IS,,ISO 217:1974,Unprocessed writing and printing paper — Method of expression of dimensions and direction of manufacture,Papiers d'écriture et d'impression vierges — Mode d'expression des dimensions et du sens de fabrication,1974-07-01,1,['85.060'],ISO/TC 6,9599,,[20074],"['en','fr']",1,

20074,IS,,ISO 217:1995,"Paper — Untrimmed sizes — Designation and tolerances for primary and supplementary ranges, and indication of machine direction","Papier — Formats bruts — Désignation et tolérances pour la série principale et la série complémentaire, et désignation du sens de fabrication",1995-12-14,2,['85.060'],ISO/TC 6,9599,"[4519,4520,4089,4691]",[36632],"['en','fr']",2,"<p>Specifies a primary range and a supplementary range of untrimmed sizes of paper in sheets which are to be trimmed to the ISO-A series of sizes given in ISO 216. Gives the method for indication of machine direction (direction of manufacture). Replaces the first edition, which has been technically revised.</p>" 200

36632,IS,,ISO 217:2008,"Paper — Untrimmed sizes — Designation and tolerances for primary and supplementary ranges, and indication of machine direction","Papier — Formats bruts — Désignation et tolérances pour la série principale et la série auxiliaire, et désignation du sens machine",2008-07-07,3,['85.060'],ISO/TC 6,9599,[20074],[63056],"['en','fr']",4,"<p>ISO 217:2008 specifies a primary range and a supplementary range of untrimmed sizes of paper in sheets which are to be trimmed to the ISO-A series of sizes as given in ISO 216, and establishes a system of designation of untrimmed sizes.</p><p>ISO 217:2008 also specifies the method for the indication of machine direction of untrimmed sizes.

6965,IS,,ISO 2170:1980,Cereals and pulses — Sampling of milled products,Céréales et légumineuses — Échantillonnage des produits de mouture,1980-02-01,2,['67.060'],ISO/TC 34/SC 4,9599,,[22637],"['en','fr']",8,

71364,IS,,ISO 21701:2019,Textiles —Test method for accelerated hydrolysis of textile materials and biodegradation under controlled composting conditions of the resulting hydrolysate,Textiles — Méthode d’essai pour hydrolyse accélérée des matières textiles et la biodégradation dans des conditions de compostage contrôlées de l'hydrolysat résultant,2019-09-04,1,['59.080.01'],ISO/TC 38,9599,,[88791],['en'],10,"<p>This document specifies a test method for the determination of the biodegradability of the hydrolysate of textile materials obtained after accelerated hydrolysis under controlled composting conditions by measurement of the amount of evolved carbon dioxide with a gas chromatography.</p><

6967,IS,,ISO 2171:1980,"Cereals, pulses and derived products — Determination of ash","Céréales, légumineuses et produits dérivés — Détermination des cendres",1980-05-01,2,['67.060'],ISO/TC 34/SC 4,9599,,[6968],"['en','fr']",3,

6968,IS,,ISO 2171:1993,Cereals and milled cereal products — Determination of total ash,Céréales et produits de mouture des céréales — Dosage des cendres totales,1993-06-17,3,['67.060'],ISO/TC 34/SC 4,9599,[6967],[37264],"['en','fr']",5,"<p>The principle of the method specified is incineration of a test portion in an oxidizing atmosphere at a temperature of 900 °C until combustion of organic matter is complete, then weighing the residue obtained. Is not applicable to starch and starch derivatives, or to cereals and derived cereal products intended for animal feeding stuffs, nor to seeds of cereals and pulses for sowing.</p>"

37264,IS,,ISO 2171:2007,"Cereals, pulses and by-products — Determination of ash yield by incineration","Céréales, légumineuses et produits dérivés — Dosage du taux de cendres par incinération",2007-10-22,4,['67.060'],ISO/TC 34/SC 4,9599,[6968],[75726],"['en','fr']",11,"<p>ISO 2171:2007 specifies a method for determining the ash yielded by cereals, pulses and their milled products intended for human consumption. The source materials covered are: a) grains of cereals; b) flours and semolinas; c) milled products (bran and high bran content products, sharps); d) mixed cereal flours (mixes); e) cereal by-products other than milled products; and f) pulses and their by-products.</p><p>ISO 2171:2007

71490,IS,,ISO 21720:2017,XLIFF (XML Localisation interchange file format),XLIFF (Format de fichier XML pour l'échange de données de localisation),2017-12-01,1,['35.240.30'],ISO/TC 37/SC 5,9599,,[87344],['en'],132,"<p>ISO 21720:2017 defines version 2.0 of the XML Localisation Interchange File Format (XLIFF). The purpose of this vocabulary is to store localizable data and carry it from one step of the localization process to the other, while allowing interoperability between and among tools.</p>"

34671,IS,,ISO 21727:2004,Cinematography — Method of measurement of perceived loudness of motion-picture audio material,Cinématographie — Méthode de mesure de l'intensité sonore percue pour les films cinématographiques,2004-09-24,1,['37.060.99'],ISO/TC 36,9599,,[69744],['en'],6,"<p>ISO 21727:2004 specifies a method of measurement of motion-picture sound that allows assessment of the subjective loudness and annoyance of the sound recording when replayed at the recommended replay level in rooms aligned with the characteristics of ISO 2969. The specified method of measurement assesses the entire duration of the sound recording with suitable channel summation, frequency weighting and time integra

6970,IS,,ISO 2173:1978,Fruit and vegetable products — Determination of soluble solids content — Refractometric method,Produits dérivés des fruits et légumes — Détermination du résidu sec soluble — Méthode réfractométrique,1978-11-01,1,['67.080.01'],ISO/TC 34/SC 3,9599,,"[35851,25127]","['en','fr']",4,"<p>The method is particularly applicable to thick products, to products containing suspendes matter and to products rich in sugars. If the products contain other dissolved substances, the results will be only approximate, nevertheless they may be considered conventionally as the soluble solids content. The principle consists in measuring of the refractive index of a test solution at 20 °C, usin

6971,IS,,ISO 2174:1979,Surface active agents — Preparation of water with known calcium hardness,Agents de surface — Préparation d'une eau de dureté calcique déterminée,1979-11-01,2,['71.100.40'],ISO/TC 91,9599,,[6972],"['en','fr']",3,

34685,IS,,ISO 21747:2006,Statistical methods — Process performance and capability statistics for measured quality characteristics,Méthodes statistiques — Performances de processus et statistiques d'aptitude pour les caractéristiques de qualité mesurées,2006-06-21,1,['03.120.30'],ISO/TC 69/SC 4,9599,,[46530],['en'],32,<p>ISO 21747:2006 describes a procedure for the determination of statistics in order to estimate the quality capability of product and process characteristics. The process results of these quality characteristics are tabularized into eight possible distribution types. Calculation formulae for the statistical values are placed with every distribution.These statistics relate to co

46373,IS,,ISO 21748:2010,"Guidance for the use of repeatability, reproducibility and trueness estimates in measurement uncertainty estimation","Lignes directrices relatives à l'utilisation d'estimations de la répétabilité, de la reproductibilité et de la justesse dans l'évaluation de l'incertitude de mesure",2010-10-25,1,['17.020'],ISO/TC 69/SC 6,9599,[34686],[71615],"['en','fr']",38,"<p>ISO 21748:2010 gives guidance for evaluation of measurement uncertainties using data obtained from studies conducted in accordance with ISO 5725-2:1994; comparison of collaborative study results with measurement uncertainty (MU) obtained using formal principles of uncertainty propagation. (ISO 5725-3:1994 pr

6973,IS,,ISO 2175:1981,Industrial wheels for non-powered equipment — Dimensions and nominal load capacities,Roues de manutention pour engins de manutention non automoteurs — Dimensions et capacités nominales de charge,1981-11-01,1,['53.060'],ISO/TC 110,9599,,"[36542,36543]","['en','fr']",5,"<p>Specifies the definition of nominal load capacity, the classification of wheels, the specification of wheels, the determination of the category and selection of a wheel and the inspection conditions of industrial wheels and castors. An Annex gives nominal load capacities.</p>"

6974,IS,,ISO 2176:1972,Petroleum products — Lubricating grease — Determination of dropping point,Produits pétroliers — Graisses lubrifiantes — Détermination du point de goutte,1972-06-01,1,['75.100'],ISO/TC 28,9599,,[6975],"['en','fr']",2,

71601,IS,,ISO 21766:2018,Tobacco and tobacco products — Determination of tobacco-specific nitrosamines in tobacco products — Method using LC-MS/MS,Tabac et produits du tabac — Dosage des nitrosamines spécifiques du tabac dans les produits du tabac — Méthode par CL-SM/SM,2018-09-21,1,['65.160'],ISO/TC 126,9599,,[81666],"['en','fr']",16,"<p>This document specifies a method for the quantification of four tobacco specific nitrosamines (TSNAs) in tobacco and the following tobacco products: cigarettes, cigars and smokeless tobacco products using reversed phase high performance liquid chromatography with tandem mass spectrometry (LC-MS/MS). The TSNAs determined with this method are: N-nitrosonornic

6976,IS,,ISO 2177:1972,Metallic coatings — Measurement of coating thickness — Coulometric method by anodic dissolution,Revêtements métalliques — Mesurage de l'épaisseur — Méthode coulométrique par dissolution anodique,1972-06-01,1,['25.220.40'],ISO/TC 107,9599,,[6977],"['en','fr']",4,

6977,IS,,ISO 2177:1985,Metallic coatings — Measurement of coating thickness — Coulometric method by anodic dissolution,Revêtements métalliques — Mesurage de l'épaisseur — Méthode coulométrique par dissolution anodique,1985-05-16,2,['25.220.40'],ISO/TC 107,9599,[6976],"[6978,37084]","['en','fr']",9,"<p>This second edition cancels and replaces the first edition (i. e. ISO 2177:1972).Typical combinations of coatings and substrates that can be tested by this method are given in table 1. The method is also applicable to multi-layer systems. In some cases, the presence and thickness of diffusion layers, and the thickness of coatings on cylindrical specimens and wires, can also be measured.</p>" 69

35989,IS,,ISO 21771:2007,Gears — Cylindrical involute gears and gear pairs — Concepts and geometry,Engrenages — Roues et engrenages cylindriques à développante — Concepts et géométrie,2007-08-28,1,['21.200'],ISO/TC 60/SC 1,9599,[10361],[84949],['en'],83,"<p>ISO 21771:2007 specifies the geometric concepts and parameters for cylindrical gears with involute helicoid tooth flanks. Flank modifications are included. It also covers the concepts and parameters for cylindrical gear pairs with parallel axes and a constant gear ratio, which consist of cylindrical gears according to it. Gear and mating gear in these gear pairs have the same basic rack tooth profile.</p>"

6979,IS,,ISO 2178:1982,Non-magnetic coatings on magnetic substrates — Measurement of coating thickness — Magnetic method,Revêtements métalliques non magnétiques sur métal de base magnétique — Mesurage de l'épaisseur du revêtement — Méthode magnétique,1982-08-01,2,"['25.220.40','25.220.50']",ISO/TC 107,9599,,[63004],"['en','fr']",4,<p>This second edition cancels and replaces the first edition (i. e. ISO 2178:1972). Specifies the method of using coating thickness instruments of the magnetic type for non-destructive measurements of the thickness. The method is applicable only for measurements on reasonably flat specimens. For non-magnetic substrates: see ISO 2361.</p>

72335,IS,,ISO 21782-1:2019,Electrically propelled road vehicles — Test specification for electric propulsion components — Part 1: General test conditions and definitions,Véhicules routiers à propulsion électrique Spécification d'essai pour les composants de propulsion électrique — Partie 1: Conditions generales et définitions,2019-08-29,1,['43.120'],ISO/TC 22/SC 37,9599,,"[80094,84290,82531]",['en'],14,"<p>This document specifies the test procedures for performance and operating load for voltage class B electric propulsion components (motor, inverter, DC/DC converter) and their combinations (motor system) of electrically propelled road vehicles.</p><p>This document specifies the terms and de

35990,IS,,ISO 21789:2009,Gas turbine applications — Safety,Applications des turbines à gaz — Sécurité,2009-02-12,1,['27.040'],ISO/TC 192,9599,,[74201],"['en','ru']",82,"<p>ISO 21789:2009 covers the safety requirements for gas turbine applications using liquid or gaseous fuels and the safety-related control and detection systems and essential auxiliaries for all types of open cycles (simple, combined, regenerative, reheat, etc.) used in onshore and offshore applications including floating production platforms.</p><p>It applies to driven machinery only where an integral part of the gas turbine (e.g. a gearbox integral to the gas turbine) or located within the gas turbine enclosure and forming

6980,IS,,ISO 2179:1972,Electroplated coatings of tin-nickel alloy,Dépôts électrolytiques d'alliages étain-nickel,1972-06-01,1,['25.220.40'],ISO/TC 107/SC 3,9599,,[6981],"['en','fr']",4,

34728,IS,,ISO 21807:2004,Microbiology of food and animal feeding stuffs — Determination of water activity,Microbiologie des aliments — Détermination de l'activité de l'eau,2004-09-13,1,['07.100.30'],ISO/TC 34/SC 9,9599,,[63379],"['en','fr']",7,"<p>ISO 21807:2004 gives basic principles and requirements for physical methods of determining the water activity of products intended for human consumption and the feeding of animals.</p><p>Water activity can be used to predict microbial growth and determine the microbiological stability of a food product, and it also provides an important, quantitatively determinable criterion for estimating the times for which a foodstuff can be kept.</p>"

35997,IS,,ISO 21809-1:2011,Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 1: Polyolefin coatings (3-layer PE and 3-layer PP),Industries du pétrole et du gaz naturel — Revêtements externes des conduites enterrées ou immergées utilisées dans les systèmes de transport par conduites — Partie 1: Revêtements à base de polyoléfines (PE tricouche et PP tricouche),2011-06-21,1,['75.200'],ISO/TC 67/SC 2,9599,,[65345],"['en','fr']",54,<p>ISO 21809-1:2011 specifies requirements of plant-applied external three-layer polyethylene- and polypropylene-based coatings for corrosion protection of welded and seamless steel

37531,IS,,ISO 21809-2:2007,Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Fusion-bonded epoxy coatings,Industries du pétrole et du gaz naturel — Revêtements externes des conduites enterrées ou immergées utilisées dans les systèmes de transport par conduites — Partie 2: Revêtements à base de résine époxydique appliquée par fusion,2007-12-03,1,['75.200'],ISO/TC 67/SC 2,9599,,[56763],"['en','fr']",37,"<p>ISO 21809-2:2007 specifies the requirements for qualification, application, testing and handling of materials for plant application of single-layer fusion-bonded epoxy (FBE) coatings applied externally

53040,IS,Cor,ISO 21809-2:2007/Cor 1:2008,Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Fusion-bonded epoxy coatings — Technical Corrigendum 1,Industries du pétrole et du gaz naturel — Revêtements externes des conduites enterrées ou immergées utilisées dans les systèmes de transport par conduites — Partie 2: Revêtements à base de résine époxydique appliquée par fusion — Rectificatif technique 1,2008-12-03,1,['75.200'],ISO/TC 67/SC 2,9599,,[56763],['en'],1,

56763,IS,,ISO 21809-2:2014,Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 2: Single layer fusion-bonded epoxy coatings,Industries du pétrole et du gaz naturel — Revêtements externes des conduites enterrées et immergées utilisées dans les systèmes de transport par conduites — Partie 2: Revêtements monocouche à base de résine époxydique appliquée par fusion,2014-10-29,2,['75.200'],ISO/TC 67/SC 2,9599,"[53040,37531]","[78288,86129]","['en','fr','ru']",50,"<p>ISO 21809-2:2014 specifies the requirements for qualification, application, testing and handling of materials for plant application of single layer f

37532,IS,,ISO 21809-3:2008,Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 3: Field joint coatings,Industries du pétrole et du gaz naturel — Revêtements externes des conduites enterrées ou immergées utilisées dans les systèmes de transport par conduites — Partie 3: Revêtements des joints soudés sur site,2008-12-02,1,['75.200'],ISO/TC 67/SC 2,9599,,[61002],['en'],99,"<p>ISO 21809-3:2008 specifies requirements for field joint coating of seamless or welded steel pipes for pipeline transportation systems in the petroleum and natural gas industries as defined in ISO 13623. ISO 21809-3:2008 specifies the qual

53418,IS,Amd,ISO 21809-3:2008/Amd 1:2011,Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 3: Field joint coatings — Amendment 1,Industries du pétrole et du gaz naturel — Revêtements externes des conduites enterrées ou immergées utilisées dans les systèmes de transport par conduites — Partie 3: Revêtements des joints soudés sur site — Amendement 1,2011-11-03,1,['75.200'],ISO/TC 67/SC 2,9599,,[61002],['en'],15,

39074,IS,,ISO 21809-4:2009,Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 4: Polyethylene coatings (2-layer PE),Industries du pétrole et du gaz naturel — Revêtements externes des conduites enterrées ou immergées utilisées dans les systèmes de transport par conduites — Partie 4: Revêtements à base de polyéthylène (PE bicouche),2009-11-05,1,['75.200'],ISO/TC 67/SC 2,9599,,[84937],['en'],34,"<p>ISO 21809-4:2009 specifies the requirements for qualification, application, inspection, testing, handling and storage of materials for plant application of two-layer polyethylene coatings (2-layer PE) applied exter

40881,IS,,ISO 21809-5:2010,Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 5: External concrete coatings,Industries du pétrole et du gaz naturel — Revêtements externes des conduites enterrées ou immergées utilisées dans les systèmes de transport par conduites — Partie 5: Revêtements externes en béton,2010-03-18,1,['75.200'],ISO/TC 67/SC 2,9599,,[68378],"['en','fr','ru']",29,"<p>ISO 21809-5:2010 specifies the requirements for qualification, application, testing and handling of materials required for the application of reinforced concrete coating externally to either bare pipe or pre-coated pipe for use i

6982,IS,,ISO 2184-1:1972,Industrial castors — Dimensions of top plates — Part 1: Oblong top-plates with 4 bolt holes,Roulettes de manutention — Dimensions des platines — Partie 1: Platines oblongues à 4 trous de fixation,1972-06-01,1,['53.060'],ISO/TC 110,9599,,"[36542,36543]","['en','fr']",2,

71959,IS,,ISO 21843:2018,Determination of the resistance to hydrocarbon pool fires of fire protection materials and systems for pressure vessels,Détermination de la résistance aux feux de nappe d'hydrocarbure des matériaux et systèmes de protection incendie des récipients sous pression,2018-10-02,1,['13.220.50'],ISO/TC 92/SC 2,9599,,[84562],['en'],36,<p>This document specifies a test method for determining the fire resistance of pressure vessels with a fire protection system when subjected to standard fire exposure conditions. It does not address vessels cooled by water deluge or water monitor. The test data thus obtained permits subsequent classification on the basis of the duration for whi

71962,IS,,ISO 21846:2018,Vegetable fats and oils — Determination of composition of triacylglycerols and composition and content of diacylglycerols by capillary gas chromatography,"Corps gras d'origine végétale — Détermination de la composition des triacylglycérols et de la teneur en diacylglycérols par chromatographie en phase gazeuse sur colonne capillaire, dans les huiles végétales",2018-08-07,1,['67.200.10'],ISO/TC 34/SC 11,9599,,[91326],['en'],13,"<p>This document specifies the determination of composition of triacylglycerols and the determination of the composition and content of diacylglycerols by capillary gas chromatography in vegetable oils with a lauric acid content below 1 %.</p><

38162,IS,,ISO 21849:2006,Aircraft and space — Industrial data — Product identification and traceability,Aéronautique et espace — Données industrielles — Identification des produits et traçabilité,2006-11-28,1,"['35.240.60','49.020']",ISO/TC 20,9599,[36004],[75600],['en'],58,"<p>ISO 21849:2006 specifies the requirements for a product identification and traceability schema for life cycle management of aircraft and space products/parts. It specifies the minimum essential identification information needed for traceability of a product for its life cycle. It also provides the data structures for use with automatic identification technologies that support product/part life cycle data management ac

6984,IS,,ISO 2186:1973,Fluid flow in closed conduits — Connections for pressure signal transmissions between primary and secondary elements,Débit des fluides dans les conduites fermées — Liaisons pour la transmission du signal de pression entre les éléments primaires et secondaires,1973-03-01,1,['17.120.10'],ISO/TC 30/SC 2,9599,,[38091],"['en','fr']",34,<p>Describes means whereby a pressure signal from a primary element can be transmitted by known techniques to a secondary device in such a way that the value of the signal is not distorted or modified even though it may be changed into a signal of a different nature. Is concerned only with the pressure difference techniques of flow measuremen

34757,IS,,ISO 21869:2006,Rubber compounding ingredients — Magnesium oxide — Methods of test,Ingrédients de mélange du caoutchouc — Oxyde de magnésium — Méthodes d'essai,2006-03-23,1,['83.040.20'],ISO/TC 45/SC 3,9599,,[80030],"['en','fr']",14,<p>ISO 21869:2006 specifies the test methods to be used for magnesium oxide intended for use in the rubber industry as a stabilizer and vulcanizing agent.</p>

6985,IS,,ISO 2187:1976,"Textile machinery and accessories — Spinning preparatory machinery, spinning and doubling (twisting) machinery — Terminology","Matériel pour l'industrie textile — Matériel de préparation de filature, de filature et de retordage — Terminologie",1976-12-01,1,"['01.040.59','59.120.10']",ISO/TC 72,9599,,[6986],"['en','fr','ru']",8,

40479,IS,,ISO 21873-1:2008,Building construction machinery and equipment — Mobile crushers — Part 1: Terminology and commercial specifications,Machines et matériels pour la construction des bâtiments — Concasseurs mobiles — Partie 1: Terminologie et spécifications commerciales,2008-06-03,1,['91.220'],ISO/TC 195,9599,,[61184],"['en','fr']",16,"<p>ISO 21873-1:2008 establishes terminology and content of commercial literature specifications for mobile crushers, mounted on crawler, truck or semi-trailer, used in the building construction industry. It is not applicable to fixed crushers.</p>"

43995,IS,,ISO 21873-2:2009,Building construction machinery and equipment — Mobile crushers — Part 2: Safety requirements,Machines et matériels pour la construction des bâtiments — Concasseurs mobiles — Partie 2: Exigences de sécurité,2009-10-09,1,['91.220'],ISO/TC 195,9599,,[68925],"['en','fr']",31,"<p>ISO 21873-2:2009 establishes the safety requirements for mobile crushers, as defined in ISO 21873-1, used in the building construction industry for crushing concrete debris and stones. It deals with all the significant hazards, hazardous situations and events relevant to mobile crushers when used as intended and under the conditions foreseen by the manufacturer.</p>"

6987,IS,,ISO 2189:1972,Cork — Expanded pure agglomerated cork — Determination of bulk density,Liège — Agglomérés expansés purs — Détermination de la masse volumique,1972-04-01,1,['79.100'],ISO/TC 87,9599,,[6988],"['en','fr']",1,

6988,IS,,ISO 2189:1986,Expanded pure agglomerated cork — Determination of bulk density,Agglomérés expansés purs de liège — Détermination de la masse volumique apparente,1986-11-13,2,['79.100'],ISO/TC 87,9599,[6987],"[28163,45311]","['en','fr']",1,"<p>Specifies a method the principle of which consists in measuring the dimensions of a test piece and determining its dried mass. The apparatus consists of electric disc saw, metal ruler and vernier caliper. Sampling shall be carried out in accordance with ISO 2219.</p>"

36804,IS,,ISO 21898:2004,Packaging — Flexible intermediate bulk containers (FIBCs) for non-dangerous goods,Emballages — Grands récipients vrac souples (GRVS) pour matières non dangereuses,2004-07-08,1,['55.180.99'],ISO/TC 122/SC 3,9599,,[83014],"['en','fr']",28,"<p>ISO 21898:2004 specifies materials, construction and design requirements, type test, certification and marking requirements for flexible intermediate bulk containers (FIBCs) intended to contain non-dangerous solid materials in powder, granular or paste form, and designed to be lifted from above by integral or detachable devices.</p><p>Guidance is also provided on the selection and safe usage of FIBCs.</p>"

6989,IS,,ISO 2190:1972,Cork — Granulated cork — Determination of moisture content,Liège — Granulés crus — Détermination de l'humidité,1972-03-01,1,['79.100'],ISO/TC 87,9599,,[6990],"['en','fr']",1,

6990,IS,,ISO 2190:1988,Granulated cork — Determination of moisture content,Granulés crus de liège — Détermination de l'humidité,1988-11-03,2,['79.100'],ISO/TC 87,9599,[6989],[23236],"['en','fr']",1,

23236,IS,,ISO 2190:1998,Granulated cork — Determination of moisture content,Granulés crus de liège — Détermination de l'humidité,1998-10-01,3,['79.100'],ISO/TC 87,9599,[6990],"[69749,54919]","['en','fr']",3,

61586,IS,,ISO 21909-1:2015,Passive neutron dosimetry systems — Part 1: Performance and test requirements for personal dosimetry,Systèmes dosimétriques passifs pour les neutrons — Partie 1: Exigences de fonctionnement et d'essai pour la dosimétrie individuelle,2015-11-30,1,['13.280'],ISO/TC 85/SC 2,9599,"[36028,50634]",[78756],"['en','fr']",39,"<p>ISO 21909-1:2015 provides performance and test requirements for determining the acceptability of neutron dosimetry systems to be used for the measurement of personal dose equivalent, Hp(10), for neutrons ranging in energy from thermal to 20 MeV[1]. No distinction between the different techniques available in the market place is made in the descripti

36028,IS,,ISO 21909:2005,Passive personal neutron dosemeters — Performance and test requirements,Dosimètres individuels passifs pour les neutrons — Exigences de fonctionnement et d'essai,2005-06-15,1,['13.280'],ISO/TC 85/SC 2,9599,,[61586],"['en','fr']",50,"<p>ISO 21909:2005 provides performance and test requirements for determining the acceptability of personal neutron dosemeters to be used for the measurement of personal dose equivalent, <i>H</i>_p(10) for neutrons ranging in energy from thermal to 20 MeV.</p>"

50634,IS,Cor,ISO 21909:2005/Cor 1:2007,Passive personal neutron dosemeters — Performance and test requirements — Technical Corrigendum 1,Dosimètres individuels passifs pour les neutrons — Exigences de fonctionnement et d'essai — Rectificatif technique 1,2007-10-30,1,['13.280'],ISO/TC 85/SC 2,9599,,[61586],['fr'],,

6991,IS,,ISO 2191:1972,Cork — Expanded pure agglomerated — Deformation under constant pressure,Liège — Agglomérés expansés purs — Déformation sous pression constante,1972-07-01,1,['79.100'],ISO/TC 87,9599,,"[52198,6992]","['en','fr']",2,"<p>The specified method determines the behaviour of this material when subjected to a constant pressure which is given in the relevant specifications and applies to corkboards which are subjected, when in use, to a continuous and uniformly distributed load.</p>"

40513,IS,,ISO 21927-2:2006,Smoke and heat control systems — Part 2: Specification for natural smoke and heat exhaust ventilators,Systèmes de contrôle de fumée et de chaleur — Partie 2: Spécifications pour les dispositifs d'évacuation naturelle des fumées et de la chaleur,2006-11-22,1,['13.220.20'],ISO/TC 21/SC 11,9599,,[70998],['en'],40,<p>ISO 21927-2:2006 specifies requirements and gives test methods for natural smoke- and heat-exhaust ventilators that are intended to be installed in a roof and/or wall as a component of a natural smoke- and heat-exhaust system.</p>

53775,IS,Amd,ISO 21927-2:2006/Amd 1:2010,Smoke and heat control systems — Part 2: Specification for natural smoke and heat exhaust ventilators — Amendment 1,Systèmes de contrôle de fumée et de chaleur — Partie 2: Spécifications pour les dispositifs d'évacuation naturelle des fumées et de la chaleur — Amendement 1,2010-05-12,1,['13.220.20'],ISO/TC 21/SC 11,9599,,[70998],['en'],2,

40514,IS,,ISO 21927-3:2006,Smoke and heat control systems — Part 3: Specification for powered smoke and heat exhaust ventilators,Systèmes de contrôle de fumée et de chaleur — Partie 3: Spécifications pour les ventilateurs mécaniques d'évacuation des fumées et de la chaleur,2006-11-22,1,['13.220.20'],ISO/TC 21/SC 11,9599,,[70999],['en'],29,"<p>ISO 21927-3:2006 specifies requirements and gives methods for testing powered smoke and heat exhaust ventilators that are intended to be installed as part of a powered smoke and heat exhaust ventilation system. It also provides a procedure for approving a range of powered smoke and heat exhaust ventilators and their motors, from a limited number of test

53774,IS,Amd,ISO 21927-3:2006/Amd 1:2010,Smoke and heat control systems — Part 3: Specification for powered smoke and heat exhaust ventilators — Amendment 1,Systèmes de contrôle de fumée et de chaleur — Partie 3: Spécifications pour les ventilateurs mécaniques d'évacuation des fumées et de la chaleur — Amendement 1,2010-05-12,1,['13.220.20'],ISO/TC 21/SC 11,9599,,[70999],['en'],2,

40435,IS,,ISO 21930:2007,Sustainability in building construction — Environmental declaration of building products,Bâtiments et ouvrages construits — Développement durable dans la construction — Déclaration environnementale des produits de construction,2007-10-01,1,['91.040.01'],ISO/TC 59/SC 17,9599,,[61694],"['en','ru']",26,"<p>ISO 21930:2007 provides the principles and requirements for type<i> </i>III environmental declarations (EPD) of building products.</p><p>ISO 21930:2007 contains specifications and requirements for the EPD of building products. Where this International Standard contains more specific requirements, it complements ISO 14025 for the EPD of building products.</p><p>ISO 219

45559,IS,,ISO 21931-1:2010,Sustainability in building construction — Framework for methods of assessment of the environmental performance of construction works — Part 1: Buildings,Développement durable dans la construction — Cadre méthodologique de l'évaluation de la performance environnementale des ouvrages de construction — Partie 1: Bâtiments,2010-06-04,1,['91.040.01'],ISO/TC 59/SC 17,9599,[40434],[71183],"['en','fr','ru']",26,"<p>ISO 21931-1:2010 provides a general framework for improving the quality and comparability of methods for assessing the environmental performance of buildings and their related external works.</p><p>It identifies and describes issues to be taken into account in t

6994,IS,,ISO 2194:1972,Wire screens and plate screens for industrial purposes — Nominal sizes of apertures,Toiles et feuilles ou plaques perforées pour tamisage industriel — Dimensions nominales des ouvertures,1972-02-01,1,['73.120'],ISO/TC 24,9599,,[6995],"['en','fr']",3,

56562,IS,,ISO 21940-21:2012,Mechanical vibration — Rotor balancing — Part 21: Description and evaluation of balancing machines,Vibrations mécaniques — Équilibrage des rotors — Partie 21: Description et évaluation des machines à équilibrer,2012-07-10,1,['21.120.40'],ISO/TC 108/SC 2,9599,[1733],[78146],['en'],53,"<p>ISO 21940-21:2012 specifies requirements for evaluating the performance of machines for balancing rotating components by the following tests: a) test for minimum achievable residual unbalance, <i>U</i>mar test; b) test for unbalance reduction ratio, URR test; c) test for couple unbalance interference on single-plane machines; d) compensator test.</p><p>These tests are performed du

30065,IS,,ISO 21949:2001,Coated abrasives — Plain sheets with holes for dust extraction,Produits abrasifs appliqués — Feuilles simples avec trous pour extraction de la poussière,2001-03-29,1,['25.100.70'],ISO/TC 29/SC 5,9599,,[84942],"['en','fr']",5,

30066,IS,,ISO 21951:2001,Coated abrasives — Plain discs with holes for dust extraction,Produits abrasifs appliqués — Disques simples avec trous pour extraction de la poussière,2001-03-29,1,['25.100.70'],ISO/TC 29/SC 5,9599,,[84940],"['en','fr']",4,

40532,IS,,ISO 21952:2007,"Welding consumables — Wire electrodes, wires, rods and deposits for gas-shielded arc welding of creep-resisting steels — Classification","Produits consommables pour le soudage — Fils-électrodes, fils, baguettes et dépôts pour le soudage à l'arc sous protection gazeuse des aciers résistant au fluage — Classification",2007-11-12,1,['25.160.20'],ISO/TC 44/SC 3,9599,,[57188],"['en','fr']",14,"<p>ISO 21952:2007 specifies requirements for classification of wire electrodes, wires and rods for gas-shielded metal arc welding and tungsten inert-gas welding of creep-resisting steels, and for their deposits in the as-welded or post-weld heat-treated condition. One wire electrod

57188,IS,,ISO 21952:2012,"Welding consumables — Wire electrodes, wires, rods and deposits for gas shielded arc welding of creep-resisting steels — Classification","Produits consommables pour le soudage — Fils-électrodes, fils, baguettes et dépôts pour le soudage à l'arc sous gaz de protection des aciers résistant au fluage — Classification",2012-05-02,2,['25.160.20'],ISO/TC 44/SC 3,9599,[40532],[86734],"['en','fr']",14,"<p>ISO 21952:2012 specifies requirements for classification of wire electrodes, wires and rods for gas shielded metal arc welding and tungsten inert-gas welding of creep-resisting steels, and for their deposits in the as-welded or post-weld heat-treated condition. One wire el

6997,IS,,ISO 2196:1975,Withdrawal of ISO 2196-1975,Annulation de l'ISO 2196-1975,1975-10-01,1,['53.040.01'],ISO/TC 101,9599,,[13741],"['en','fr']",2,

34781,IS,,ISO 21968:2005,Non-magnetic metallic coatings on metallic and non-metallic basis materials — Measurement of coating thickness — Phase-sensitive eddy-current method,Revêtements métalliques non magnétiques sur des matériaux de base métalliques et non métalliques — Mesurage de l'épaisseur de revêtement — Méthode par courants de Foucault sensible aux variations de phase,2005-07-29,1,['25.220.40'],ISO/TC 107,9599,,[73285],"['en','fr','ru']",12,"<p>ISO 21968:2005 describes a method of using phase-sensitive eddy-current instruments for non-destructive measurements of the thickness of non-magnetic metallic coatings on metallic and non-metallic basis materials such as zinc, cadmium, copper,

36038,IS,,ISO 21969:2005,High-pressure flexible connections for use with medical gas systems,Raccords flexibles haute pression pour utilisation avec les systèmes de gaz médicaux,2005-03-16,1,['11.040.10'],ISO/TC 121/SC 6,9599,,[52967],"['en','fr']",13,<p>ISO 21969:2005 applies to high-pressure flexible connections intended to be connected to cylinders or cylinder bundles with nominal filling pressures up to 25 000 kPa at 15 °C for use with the following medical gases:</p><p>oxygen; nitrous oxide; air for breathing;helium; carbon dioxide; xenon; mixtures of these gases; air for driving surgical tools; nitrogen for driving surgical tools.</p><p>ISO 21969:2005 applies to high-pressure flexible

72322,IS,,ISO 21970-1:2018,Plastics — Polyketone (PK) moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Polycétone (PK) pour moulage et extrusion — Partie 1: Système de désignation et base de spécification,2018-08-23,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[77533],"['en','fr']",8,"<p>This document establishes a system of designation for polyketone (PK) moulding and extrusion materials which may be used as the basis for specifications. Polyketone polymer chains are built up from regularly alternating olefinic units and keto groups. The olefinic units shall be randomly distributed ethylene and propylene.</p><p>The types of polyketone plastics

72323,IS,,ISO 21970-2:2018,Plastics — Polyketone (PK) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Polycétone (PK) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés,2018-09-03,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[77534],"['en','fr']",6,"<p>This document specifies the methods of preparation of test specimens and the standard test methods to be used in determining the properties of thermoplastic polyketone moulding and extrusion materials. Requirements for handling test material and/or conditioning both the test material before moulding and the specimens before testing are

71639,IS,,ISO 21978:2021,Heat pump water heater — Testing and rating at part load conditions and calculation of seasonal coefficient of performance for space heating,Chauffe-eau à pompe à chaleur — Essais et classification à charge partielle et calcul du coefficient de performance saisonnier,2021-02-03,1,['27.080'],ISO/TC 86/SC 6,9599,,[83633],['en'],47,"<p>The document specifies test conditions for determining the seasonal performance characteristics of air source heat pump water heaters for space heating with electrically driven compressors with or without supplementary heater. The purpose of this document is to rate performance of the heat pump water heaters for space heating with no oper

50656,IS,,ISO 21987:2009,Ophthalmic optics — Mounted spectacle lenses,Optique ophtalmique — Verres ophtalmiques montés,2009-10-01,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[65161],"['en','fr']",17,<p>ISO 21987:2009 specifies requirements for mounted spectacle lenses relative to the prescription order.</p>

40588,IS,,ISO 21994:2007,Passenger cars — Stopping distance at straight-line braking with ABS — Open-loop test method,Voitures particulières — Distance d'arrêt de freinage en ligne droite avec ABS — Méthode d'essai en boucle ouverte,2007-06-11,1,['43.040.40'],ISO/TC 22/SC 33,9599,,[84163],['en'],25,"<p>ISO 21944:2007 specifies an open-loop test method to determine the stopping distance of a vehicle during a straight-line braking manoeuvre, with the Anti-lock Braking System (ABS) fully engaged. It applies to passenger cars as defined in ISO 3833 and light trucks. </p><p>ISO 21944:2007 specifies a reference method and is especially designed to ensure high repeatability.</p>"

3608,IS,,ISO 22:1975,Flat transmission belts and corresponding pulleys — Widths,Courroies plates de transmission et poulies correspondantes — Largeurs,1975-05-01,1,['21.220.10'],ISO/TC 41,9599,,[3609],"['en','fr']",1,

35466,IS,,ISO 22000:2005,Food safety management systems — Requirements for any organization in the food chain,Systèmes de management de la sécurité des denrées alimentaires — Exigences pour tout organisme appartenant à la chaîne alimentaire,2005-08-30,1,"['03.100.70','67.020']",ISO/TC 34/SC 17,9599,,[65464],"['ar','en','es','fr','ru']",32,"<p>ISO 22000:2005 specifies requirements for a food safety management system where an organization in the food chain needs to demonstrate its ability to contr

43982,IS,Cor,ISO 22000:2005/Cor 1:2006,Food safety management systems — Requirements for any organization in the food chain — Technical Corrigendum 1,Systèmes de management de la sécurité des denrées alimentaires — Exigences pour tout organisme appartenant à la chaîne alimentaire — Rectificatif technique 1,2006-02-15,1,"['03.100.70','67.020']",ISO/TC 34/SC 17,9599,,[65464],['fr'],,

40615,IS,,ISO 22007-1:2009,Plastics — Determination of thermal conductivity and thermal diffusivity — Part 1: General principles,Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique — Partie 1: Principes généraux,2009-06-15,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[67901],"['en','fr','ru']",17,"<p>ISO 22007-1:2009 describes the background to methods for the determination of the thermal conductivity and thermal diffusivity of polymeric materials. Different techniques are available for these measurements and some may be better suited than others for a particular type, state and form of material. ISO 22007-1 provides a broad overview of these techniques. Standards

67901,IS,,ISO 22007-1:2017,Plastics — Determination of thermal conductivity and thermal diffusivity — Part 1: General principles,Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique — Partie 1: Principes généraux,2017-10-13,2,['83.080.01'],ISO/TC 61/SC 5,9599,[40615],[85974],"['en','fr']",19,"<p>ISO 22007-1:2017 describes the background to methods for the determination of the thermal conductivity and thermal diffusivity of polymeric materials. Different techniques are available for these measurements and some may be better suited than others for a particular type, state and form of material. ISO 22007-1:2017 provides a broad overview of these techniques. Sta

40683,IS,,ISO 22007-2:2008,Plastics — Determination of thermal conductivity and thermal diffusivity — Part 2: Transient plane heat source (hot disc) method,Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique — Partie 2: Méthode de la source plane transitoire (disque chaud),2008-12-08,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[61190],"['en','fr']",17,"<p>ISO 22007-2:2008 specifies a method for the determination of the thermal conductivity and thermal diffusivity, and hence the specific heat capacity per unit volume, of plastics. The experimental arrangement can be designed to match different specimen sizes. Measurements can be made in gaseous and vacuum environme

61190,IS,,ISO 22007-2:2015,Plastics — Determination of thermal conductivity and thermal diffusivity — Part 2: Transient plane heat source (hot disc) method,Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique — Partie 2: Méthode de la source plane transitoire (disque chaud),2015-08-05,2,['83.080.01'],ISO/TC 61/SC 5,9599,[40683],[81836],"['en','fr']",20,"<p>ISO 22007-2:2015 specifies a method for the determination of the thermal conductivity and thermal diffusivity, and hence the specific heat capacity per unit volume of plastics. The experimental arrangement can be designed to match different specimen sizes. Measurements can be made in gaseous and vacuum env

42047,IS,,ISO 22007-4:2008,Plastics — Determination of thermal conductivity and thermal diffusivity — Part 4: Laser flash method,Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique — Partie 4: Méthode flash laser,2008-12-08,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[65085],"['en','fr']",12,"<p>ISO 22007-4:2008 specifies a method for the determination of the thermal diffusivity of a thin solid disc of plastics in the thickness direction by the laser flash method. This method is based upon the measurement of the temperature rise at the rear face of the thin-disc specimen produced by a short energy pulse on the front face.</p><p>The method can be used for homogeneo

65085,IS,,ISO 22007-4:2017,Plastics — Determination of thermal conductivity and thermal diffusivity — Part 4: Laser flash method,Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique — Partie 4: Méthode flash laser,2017-06-28,2,['83.080.01'],ISO/TC 61/SC 5,9599,[42047],[86202],"['en','fr']",17,"<p>ISO 22007-4:2017 specifies a method for the determination of the thermal diffusivity of a thin solid disc of plastics in the thickness direction by the laser flash method. This method is based upon the measurement of the temperature rise at the rear face of the thin-disc specimen produced by a short energy pulse on the front face.</p><p>The method can be used for ho

51251,IS,,ISO 22009:2009,Space systems — Space environment (natural and artificial) — Model of the earth's magnetospheric magnetic field,Systèmes spatiaux — Environnement spatial (naturel et artificiel) — Modèle du champ magnétique de la magnétosphère de la terre,2009-11-12,1,['49.140'],ISO/TC 20/SC 14,9599,,[81698],['en'],15,"<p>ISO 22009:2009 describes the main magnetospheric large-scale current systems and the magnetic field in the earth's magnetosphere and provides the main requirements for a model of the magnetospheric magnetic field. Ionospheric currents are not considered in ISO 22009:2009. ISO 22009:2009 includes a worked example of the model and establishes the parameters of magneto

42441,IS,,ISO 22010:2007,Space systems — Mass properties control,Systèmes spatiaux — Contrôle des propriétés de masse,2007-12-04,1,['49.140'],ISO/TC 20/SC 14,9599,,"[61577,81693]",['en'],13,"<p>ISO 22010:2007 describes a process for managing, controlling and monitoring the mass properties of space systems. The relationship between this management plan and the performance parameters for mass properties to be met throughout the mission is described. Ground handling, dynamics analysis and test set-ups that rely on accurate mass properties inputs are identified. ISO 22010:2007 covers all programme phases from pre-proposal through to end of life.</p>"

37161,IS,,ISO 22028-1:2004,"Photography and graphic technology — Extended colour encodings for digital image storage, manipulation and interchange — Part 1: Architecture and requirements","Photographie et technologie graphique — Codages par couleurs étendues pour stockage, manipulation et échange d'image numérique — Partie 1: Architecture et exigences",2004-03-24,1,"['37.040.99','37.100.01']",ISO/TC 42,9599,,[68761],['en'],47,"<p>ISO 22028-1:2004 specifies a set of requirements to be met by any extended-gamut colour encoding that is to be used for digital photography and/or graphic technology applications involving digital image storage, manipulation and/or interchange. ISO 22028-1:2004 is a

50026,IS,Cor,ISO 22028-1:2004/Cor 1:2007,"Photography and graphic technology — Extended colour encodings for digital image storage, manipulation and interchange — Part 1: Architecture and requirements — Technical Corrigendum 1","Photographie et technologie graphique — Codages par couleurs étendues pour stockage, manipulation et échange d'image numérique — Partie 1: Architecture et exigences — Rectificatif technique 1",2007-09-20,1,"['37.040.99','37.100.01']",ISO/TC 42,9599,,[68761],['en'],1,

36060,IS,,ISO 22029:2003,Standard file format for spectral data exchange,Format standard de fichier pour échange de données spectrométriques,2003-12-10,1,['71.040.99'],ISO/TC 202,9599,,[56211],['en'],9,"<p>ISO 22029:2003 presents a simple format for the exchange of digital spectral data that has been designated as an EMSA/MAS standard. This format is readable by both humans and computers and is suitable for transmission through various electronic networks (BITNET, ARPANET), the phone system (with modems) or on physical computer storage devices (such as floppy disks). The format is not tied to any one computer, programming language or computer operating system.</p>"

56211,IS,,ISO 22029:2012,Microbeam analysis — EMSA/MAS standard file format for spectral-data exchange,Analyse par microfaisceaux — Format de fichier standard EMSA/MAS pour échange de données spectrométriques,2012-09-03,2,['71.040.99'],ISO/TC 202,9599,[36060],[78268],['en'],10,"<p>ISO 22029:2012 presents a simple format for the exchange of digital spectral data that has been designated as an EMSA/MAS standard. This format is readable by both humans and computers and is suitable for transmission through various electronic networks, the phone system (with modems) or on physical computer storage devices (such as removable media). The format is not tied to any one computer, programming language

36069,IS,,ISO 22032:2006,Water quality — Determination of selected polybrominated diphenyl ethers in sediment and sewage sludge — Method using extraction and gas chromatography/mass spectrometry,Qualité de l'eau — Dosage d'une sélection d'éthers diphényliques polybromés dans des sédiments et des boues d'épuration — Méthode par extraction et chromatographie en phase gazeuse/spectrométrie de masse,2006-12-08,1,['13.060.50'],ISO/TC 147/SC 2,9599,,[86731],"['en','fr']",26,"<p>ISO 22032:2006 specifies a method for the determination of selected polybrominated diphenyl ethers (PBDE) in sediment and sludge using gas chromatography/mass spectrometry (GC-MS) in the electron impact (EI) or negative ion

40648,IS,,ISO 22033:2005,Nickel alloys — Determination of niobium — Inductively coupled plasma atomic emission spectrometric method,Alliages de nickel — Dosage du niobium — Méthode par spectrométrie d'émission atomique à plasma induit par haute fréquence,2005-11-10,1,['77.120.40'],ISO/TC 155,9599,,[57804],"['en','fr']",11,"<p>ISO 22033:2005 specifies an inductively coupled plasma atomic emission spectrometric method for the determination of the mass fraction of niobium between 0,1 % and 10 % in nickel alloys.</p>"

40650,IS,,ISO 22034-2:2007,Steel wire and wire products — Part 2: Tolerances on wire dimensions,Fil et produits de fil en acier — Partie 2: Tolérances sur les dimensions des fils,2007-09-18,1,['77.140.65'],ISO/TC 17/SC 17,9599,,[62680],"['en','ru']",5,"<p>ISO 22034-2:2007 specifies the tolerances on the diameter of round wire and, where applicable, on the length of round wire cut to length, for bright (i.e. uncoated) steel wire, metallic-coated steel wire and non-metallic-coated steel wire.</p>"

40653,IS,,ISO 22036:2008,Soil quality — Determination of trace elements in extracts of soil by inductively coupled plasma - atomic emission spectrometry (ICP - AES),Qualité du sol — Dosage des éléments traces dans des extraits de sol par spectrométrie d'émission atomique avec plasma induit par haute fréquence (ICP-AES),2008-12-09,1,['13.080.10'],ISO/TC 190/SC 3,9599,,[82632],"['en','fr']",30,"<p>ISO 22036:2008 describes the determination of trace elements in digests or extraction solutions from soil by inductively coupled plasma - atomic emission spectrometry (ICP-AES) for 34 elements.</p><p>This multi-element determination method is applicable to soil extracts obtained with aqua regia in ac

7009,IS,,ISO 2206-1:1972,"Packaging — Complete, filled transport packages — Part 1: Identification of parts when testing",Emballages — Emballages d'expédition complets et pleins — Partie 1: Identification des différentes parties en vue des essais,1972-04-01,1,['55.180.40'],ISO/TC 122,9599,,[7010],['en'],1,

72487,IS,,ISO 22065:2019,Workplace air — Gases and vapours — Requirements for evaluation of measuring procedures using pumped samplers,Air des lieux de travail — Gaz et vapeurs — Exigences pour l'évaluation des procédures de mesure à l'aide de dispositifs de prélèvement par pompage,2019-05-31,1,['13.040.30'],ISO/TC 146/SC 2,9599,,[81019],"['en','fr']",38,"<p>This document specifies performance requirements and test methods under prescribed laboratory conditions for the evaluation of pumped samplers used in conjunction with an air sampling pump and of procedures using these samplers for the determination of gases and vapours in workplace atmospheres.</p><p>This document addresses requirements

36077,IS,,ISO 22072:2005,Aerospace — Electrohydrostatic actuator (EHA) — Characteristics to be defined in procurement specifications,Aéronautique et espace — Actionneurs électrohydrostatiques (EHA) — Caractéristiques à définir dans les spécifications d'approvisionnement,2005-06-13,1,['49.080'],ISO/TC 20/SC 10,9599,,[54442],['en'],11,"<p>ISO 22072:2005 defines the general characteristics, requirements and design data to be included in the procurement technical specification of an electrohydrostatic actuator (EHA) to be used to power aircraft control surfaces or other moving parts of an aerospace vehicle.</p>"

61871,IS,,ISO 22077-1:2015,Health informatics — Medical waveform format — Part 1: Encoding rules,Informatique de santé — Format de la forme d'onde médicale — Partie 1: Règles d'encodage,2015-04-16,1,['35.240.80'],ISO/TC 215,9599,"[61683,41602]",[82112],['en'],42,"<p>ISO 22077-1:2015 specifies how medical waveforms, such as electrocardiogram, electroencephalogram, spirometry waveform, etc., are described for interoperability among healthcare information systems.</p><p>This International Standard may be used with other relevant protocols, such as HL7, DICOM, ISO/IEEE 11073, and database management systems for each purpose.</p><p>This is a general specification, so specifications for particular

34864,IS,,ISO 22090-1:2002,Ships and marine technology — Transmitting heading devices (THDs) — Part 1: Gyro-compasses,Navires et technologie maritime — Dispositifs de pilotage à transmission de données — Partie 1: Compas gyroscopiques,2002-09-26,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[62178],"['en','ru']",12,"<p>ISO 22090-1 specifies the construction, performance and testing of gyro-compasses as transmitting heading devices required by chapter V, SOLAS 1974 (as amended).</p><p>A transmitting heading device (THD) is an electronic device that provides information about the ship's true heading.</p><p>The THDs complying with the requirements contained in this part of ISO 22090 can be used for headi

41651,IS,Cor,ISO 22090-1:2002/Cor 1:2005,Ships and marine technology — Transmitting heading devices (THDs) — Part 1: Gyro-compasses — Technical Corrigendum 1,Navires et technologie maritime — Dispositifs de pilotage à transmission de données — Partie 1: Compas gyroscopiques — Rectificatif technique 1,2005-01-04,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[62178],"['en','ru']",1,

34887,IS,,ISO 22090-2:2004,Ships and marine technology — Transmitting heading devices (THDs) — Part 2: Geomagnetic principles,Navires et technologie maritime — Dispositifs de transmission de données de pilotage — Partie 2: Principes géomagnétiques,2004-05-21,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[62179],"['en','ru']",10,"<p>ISO 22090-2:2004 specifies the construction, performance and testing of devices employing only magnetic means as transmitting heading devices required by chapter V, SOLAS 1974 (as amended).</p>"

41652,IS,Cor,ISO 22090-2:2004/Cor 1:2005,Ships and marine technology — Transmitting heading devices (THDs) — Part 2: Geomagnetic principles — Technical Corrigendum 1,Navires et technologie maritime — Dispositifs de transmission de données de pilotage — Partie 2: Principes géomagnétiques — Rectificatif technique 1,2005-01-04,1,['47.020.70'],ISO/TC 8/SC 6,9599,,[62179],"['en','ru']",1,