Withdrawn and superseded ISO standards — page 70 of 246

34107,IS,,ISO 1925:2001,Mechanical vibration — Balancing — Vocabulary,Vibrations mécaniques — Équilibrage — Vocabulaire,2001-03-22,4,"['21.120.40','01.040.21']",ISO/TC 108/SC 2,9599,"[6621,31724,6620]","[68131,57707,39825]","['en','fr']",47,

39005,IS,,ISO 19252:2008,Plastics — Determination of scratch properties,Plastiques — Détermination du comportement à la rayure,2008-11-27,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[84392],['en'],18,"<p>ISO 19252:2008 specifies a method for determining the scratch properties of plastics under defined conditions. The method involves making a scratch by moving a hard instrument (scratch tip) of specified geometry under specified conditions of load and speed across the surface of a test specimen and then assessing the result.</p><p>The method is used to investigate the behaviour of specified types of specimen under the scratch conditions defined and for classifying the type of scratch of specimens wi

33772,IS,,ISO 19258:2005,Soil quality — Guidance on the determination of background values,Qualité du sol — Guide pour la détermination des valeurs de bruit de fond,2005-12-06,1,['13.080.99'],ISO/TC 190/SC 7,9599,,"[67982,62601]","['en','fr']",24,<p>ISO 19258:2005 provides guidance on the principles and main methods for the determination of pedo-geochemical background values and background values for inorganic and organic substances in soils. ISO 19258:2005 gives guidance on strategies for sampling and data processing and identifies methods for sampling and analysis. ISO 19258:2005 does not give guidance on the determination of background values for groundwater and sediments.</p>

64157,IS,,ISO 19259:2015,Plain bearings — Bearings with embedded solid lubricants,Paliers lisses — Paliers avec lubrifiants solide incorporé,2015-09-17,1,['21.100.10'],ISO/TC 123/SC 7,9599,,[82994],['en'],12,<p>ISO 19259:2015 specifies a bearing with embedded solid lubricants which has been widely used as a solid lubricant bearing.</p>

6622,IS,,ISO 1926:1979,Cellular plastics — Determination of tensile properties of rigid materials,Plastiques alvéolaires — Détermination des caractéristiques de traction des matériaux rigides,1979-06-01,2,['83.100'],ISO/TC 61/SC 10,9599,,"[6623,34845]","['en','fr']",4,"<p>Applies primarily to ceelular materials having a sufficient compression resistance to permit suitable gripping of the test pieces. The test piece of a given shape is subjected to a tensile stress, transmitted to the test piece by means of a suitable device. The corresponding stress-strain curve shall be recorded. In the case of low compression resistance the bonding of reinforcing metall plates to the gripping ends of test

34845,IS,,ISO 1926:2005,Rigid cellular plastics — Determination of tensile properties,Plastiques alvéolaires rigides — Détermination des caractéristiques en traction,2005-06-22,3,['83.100'],ISO/TC 61/SC 10,9599,[6622],[52864],['en'],6,"<p>ISO 1926:2005 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.</p><p>It applies primarily to cellular materials having a compression resistance sufficient to permit suitable gripping of the test specimens. If it is impossible to grip the test specimen, the method is modified so that the ends of the specimen are reinforced with metal plates.</p>"

6624,IS,,ISO 1927:1975,Refractory products — Classification of prepared unshaped refractory materials (dense and insulating),Matériaux réfractaires — Classification des matériaux réfractaires non façonnés préparés (denses et isolants),1975-12-01,1,['81.080'],ISO/TC 33,9599,,[6625],"['en','fr']",3,

6625,IS,,ISO 1927:1984,Prepared unshaped refractory materials (dense and insulating) — Classification,Matériaux réfractaires non façonnés préparés (denses et isolants) — Classification,1984-11-01,2,['81.080'],ISO/TC 33,9599,[6624],"[50738,25130]","['en','fr']",4,

6626,IS,,ISO 1928:1976,"Solid mineral fuels — Determination of gross calorific value by the calorimeter bomb method, and calculation of net calorific value","Combustibles minéraux solides — Détermination du pouvoir calorifique supérieur selon la méthode à la bombe calorimétrique, et calcul du pouvoir calorifique inférieur",1976-12-01,1,['75.160.10'],ISO/TC 27,9599,,[20747],"['en','fr']",14,

20747,IS,,ISO 1928:1995,"Solid mineral fuels — Determination of gross calorific value by the bomb calorimetric method, and calculation of net calorific value","Combustibles minéraux solides — Détermination du pouvoir calorifique supérieur selon la méthode à la bombe calorimétrique, et calcul du pouvoir calorifique inférieur",1995-08-31,2,['75.160.10'],ISO/TC 27/SC 5,9599,[6626],[41592],"['en','fr']",45,"<p>Specifies a method for the determination of the gross calorific value of a solid mineral fuel in a bomb calorimeter. Gives formulae for calculating the net calorific value at constant pressure and volume. Presents general principles and procedures for the calibrations. Cancels and replaces

41592,IS,,ISO 1928:2009,Solid mineral fuels — Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value,Combustibles minéraux solides — Détermination du pouvoir calorifique supérieur par la méthode de la bombe calorimétrique et calcul du pouvoir calorifique inférieur,2009-05-26,3,['75.160.10'],ISO/TC 27/SC 5,9599,[20747],[75883],"['en','fr','ru']",59,"<p>ISO 1928:2009 specifies a method for the determination of the gross calorific value of a solid mineral fuel at constant volume and at the reference temperature of 25 °C in a bomb calorimeter calibrated by combustion of certified benzoic acid.</p><p>The result obtained is the gross calorific

75883,IS,,ISO 1928:2020,Coal and coke — Determination of gross calorific value,Charbon et coke — Détermination du pouvoir calorifique supérieur,2020-10-05,4,['75.160.10'],ISO/TC 27/SC 5,9599,[41592],[86999],['en'],62,"<p>This document specifies a method for the determination of the gross calorific value of a solid mineral fuel at constant volume and at the reference temperature of 25 °C in a combustion vessel calorimeter calibrated by combustion of certified benzoic acid.</p><p>The result obtained is the gross calorific value of the analysis sample at constant volume with all the water of the combustion products as liquid water. In practice, fuel is burned at constant (atmospheric) pressure

64256,IS,,ISO 19281:2016,"Air cargo — Fire resistant containers — Design, performance and testing requirements","Fret aérien — Conteneurs résistant au feu — Exigences de conception, performances et essais",2016-01-28,1,['55.180.30'],ISO/TC 20/SC 9,9599,,[84968],['en'],20,"<p>ISO 19281:2016 the minimum design and performance criteria and testing methods of passive fire resistant containers (FRCs) for carriage on aircraft main deck, to be used on either of the following:</p><p>a) in those cargo compartments of civil transport aircraft where they constitute one means of complying with applicable airworthiness regulations;</p><p>b) on a voluntary basis, when deemed appropriate by operators

6627,IS,,ISO 1929:1974,"Abrasive belts — Designation, dimensions and tolerances","Bandes abrasives — Désignation, dimensions et tolérances",1974-11-01,1,['25.100.70'],ISO/TC 29/SC 5,9599,,[20540],['en'],2,

64297,IS,,ISO 19290:2016,Cigarettes — Determination of tobacco specific nitrosamines in mainstream cigarette smoke — Method using LC-MS/MS,Cigarettes — Dosage des nitrosamines spécifiques du tabac dans le courant principal de fumée de cigarette — Méthode par CL-SM/SM,2016-11-28,1,['65.160'],ISO/TC 126,9599,,[81665],"['en','fr']",14,"<p>ISO 19290:2016 specifies a method for the quantification of four tobacco specific nitrosamines (TSNAs) in the total particulate matter of mainstream cigarette smoke by using reversed phase high performance liquid chromatography with tandem mass spectrometry (LC-MS/MS). The quantified TSNAs are: N-nitrosonornicotine (NNN), N-nitrosoanatabine (NAT), N-nitrosoana

33783,IS,,ISO 19318:2004,Surface chemical analysis — X-ray photoelectron spectroscopy — Reporting of methods used for charge control and charge correction,Analyse chimique des surfaces — Spectroscopie de photoélectrons — Indication des méthodes mises en oeuvre pour le contrôle et la correction de la charge,2004-05-05,1,['71.040.40'],ISO/TC 201/SC 7,9599,,[81448],['en'],11,<p>ISO 19318:2004 specifies the minimum amount of information describing the methods of charge control and charge correction in measurements of core-level binding energies for insulating specimens by X-ray photoelectron spectroscopy that shall be reported with the analytical results. Information is also provided on methods

39049,IS,,ISO 19332:2007,Oil of blue chamomile (Chamomilla recutita (L.) Rauschert syn. Matricaria chamomilla auct.),Huile essentielle de camomille bleue (Chamomilla recutita (L.) Rauschert syn. Matricaria chamomilla auct.),2007-10-09,1,['71.100.60'],ISO/TC 54,9599,,[77271],"['en','fr']",9,"<p>ISO 19332:2007 specifies certain characteristics of the oil of blue chamomile [<i>Chamomilla recutita</i> (L.) Rauschert syn. <i>Matricaria chamomilla</i> auct.], in order to facilitate assessment of its quality.</p>"

39051,IS,,ISO 19334:2006,Binders for paints and varnishes — Gum rosin — Gas-chromatographic analysis,Liants pour peintures et vernis — Gomme-résine — Analyse par chromatographie en phase gazeuse,2006-11-22,1,"['87.040','87.060.20']",ISO/TC 35,9599,,[54541],"['en','ru']",7,<p>ISO 19334:2006 specifies a gas-chromatographic method for determining the amounts of certain rosin acids in gum rosin using capillary gas-chromatographic separation of the volatile methyl esters of these acids. It intended primarily to permit the identification of gum rosin from specific species of pine trees. It is not designed for the quantitative analysis of gum rosin.</p>

33785,IS,,ISO 19338:2003,Performance and assessment requirements for design standards on structural concrete,Exigences de performance et d'évaluation pour la conception des normes relatives au béton structurel,2003-12-11,1,['91.080.40'],ISO/TC 71/SC 4,9599,,[46094],"['en','fr']",12,"<p>ISO 19338:2003 provides performance and assesment requirements for design standards for structural concrete. It can be used for international harmonization of design and construction requirements. </p><p>ISO 19338:2003 includes requirements, which define the required structural concrete performance, criteria, which give means for expressing the requirements, and assessment clauses, which give acceptable method

40850,IS,Cor,ISO 19338:2003/Cor 1:2004,Performance and assessment requirements for design standards on structural concrete — Technical Corrigendum 1,Exigences de performance et d'évaluation pour la conception des normes relatives au béton structurel — Rectificatif technique 1,2004-12-15,1,['91.080.40'],ISO/TC 71/SC 4,9599,,[46094],"['en','fr']",1,

46094,IS,,ISO 19338:2007,Performance and assessment requirements for design standards on structural concrete,Exigences de performance et d'évaluation pour la conception des normes relatives au béton structurel,2007-09-25,2,['91.080.40'],ISO/TC 71/SC 4,9599,"[33785,40850]",[60852],"['en','fr']",12,"<p>ISO 19338:2007 provides performance and assessment requirements for design standards for structural concrete. It can be used for international harmonization of design and construction requirements.</p><p>ISO 19338:2007 includes requirements that define the required structural concrete performance, criteria that give means for expressing the requirements, and assessment clauses, which give accept

51679,IS,Cor,ISO 19338:2007/Cor 1:2008,Performance and assessment requirements for design standards on structural concrete — Technical Corrigendum 1,Exigences de performance et d'évaluation pour la conception des normes relatives au béton structurel — Rectificatif technique 1,2008-06-04,2,['91.080.40'],ISO/TC 71/SC 4,9599,,[60852],"['en','fr']",1,

54761,IS,Cor,ISO 19338:2007/Cor 2:2009,Performance and assessment requirements for design standards on structural concrete — Technical Corrigendum 2,Exigences de performance et d'évaluation pour la conception des normes relatives au béton structurel — Rectificatif technique 2,2009-07-13,2,['91.080.40'],ISO/TC 71/SC 4,9599,,[60852],"['en','fr']",1,

60852,IS,,ISO 19338:2014,Performance and assessment requirements for design standards on structural concrete,Exigences de performance et d'évaluation pour la conception des normes relatives au béton structurel,2014-09-17,3,['91.080.40'],ISO/TC 71/SC 4,9599,"[54761,46094,51679]",[79770],['en'],10,"<p>ISO 19338:2014 provides performance and assessment requirements for design standards of structural concrete. It can be used for international harmonization of design and construction requirements.</p><p>ISO 19338:2014 includes requirements, which define the required structural concrete performance; criteria, which give means for expressing the requirements; and assessment clauses, which give acce

39061,IS,,ISO 19353:2005,Safety of machinery — Fire prevention and protection,Sécurité des machines — Prévention et protection contre l'incendie,2005-02-08,1,['13.110'],ISO/TC 199,9599,,[60177],"['en','fr']",19,"<p>ISO 19353:2005 specifies methods for identifying fire hazards resulting from machinery and performing a corresponding risk assessment. It gives the basic concepts and methodology of technical fire-prevention and -protection measures to be taken during the machinery's design and construction. Its purpose is the attainment of the required safety level according to the intended use of the machinery by application of technical measures for machinery -- such measures being mainly integ

60177,IS,,ISO 19353:2015,Safety of machinery — Fire prevention and fire protection,Sécurité des machines — Prévention et protection contre l'incendie,2015-12-16,2,['13.110'],ISO/TC 199,9599,[39061],[76473],"['en','fr']",35,"<p>ISO 19353:2015 specifies methods for identifying fire hazards resulting from machinery and for performing a risk assessment.</p><p>It gives the basic concepts and methodology of protective measures for fire prevention and protection to be taken during the design and construction of machinery. The measures consider the intended use and reasonably foreseeable misuse of the machine.</p><p>It provides guidelines for consideration in reducing the risk of machinery fires to

64698,IS,,ISO 19361:2017,Measurement of radioactivity — Determination of beta emitters activities — Test method using liquid scintillation counting,Mesurage de la radioactivité — Détermination de l'activité des radionucléides émetteurs bêta — Méthode d'essai par comptage des scintillations en milieu liquide,2017-08-10,1,['17.240'],ISO/TC 85/SC 2,9599,,[87740],"['en','fr']",20,"<p>ISO 19361:2017 applies to liquid scintillation counters and requires the preparation of a scintillation source obtained by mixing the test sample and a scintillation cocktail. The test sample can be liquid (aqueous or organic), or solid (particles or filter or planchet).</p><p>ISO 19361:2017describes the conditions

73547,IS,,ISO 19363:2020,Electrically propelled road vehicles — Magnetic field wireless power transfer — Safety and interoperability requirements,Véhicules routiers électriques — Transmission d’énergie sans fil par champ magnétique — Exigences de sécurité et d'interopérabilité,2020-04-03,1,['43.120'],ISO/TC 22/SC 37,9599,[64700],[81300],"['en','fr']",39,<p>This document defines the requirements and operation of the on-board vehicle equipment that enables magnetic field wireless power transfer (MF-WPT) for traction battery charging of electric vehicles. It is intended to be used for passenger cars and light duty vehicles.</p><p>This document addresses the following aspects for an EV device:</

41132,IS,,ISO 1938-1:2015,Geometrical product specifications (GPS) — Dimensional measuring equipment — Part 1: Plain limit gauges of linear size,Spécification géométrique des produits (GPS) — Équipement de mesure dimensionnel — Partie 1: Calibres lisses à limite de taille linéaire,2015-10-26,1,['17.040.10'],ISO/TC 213,9599,[6628],[87858],"['en','fr']",30,"<p>ISO 1938-1:2015 specifies the most important metrological and design characteristics of plain limit gauges of linear size.</p><p>ISO 1938-1:2015 defines the different types of plain limit gauges used to verify linear dimensional specifications associated with linear size.</p><p>ISO 1938-1:2015 also defines the design characteristics and

64772,IS,,ISO 19385:2017,"Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for water jetting or water blasting applications — Specification","Tuyaux et flexibles en caoutchouc et en plastique, à armature textile ou métallique, pour applications à jet d'eau à haute et ultra haute pression — Spécifications",2017-10-04,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[75386],"['en','fr']",13,"<p>ISO 19385 specifies requirements for nine classes of reinforced hydraulic hoses and hose assemblies of nominal sizes ranging from 5 to 25. Each class has a single maximum working pressure. Such hoses and hose assemblies are intended to be used with very high-pressure water jetting and wat

75423,IS,Amd,ISO 19385:2017/Amd 1:2019,"Rubber and plastics hoses and hose assemblies, wire- or textile-reinforced, for water jetting or water blasting applications — Specification — Amendment 1","Tuyaux et flexibles en caoutchouc et en plastique, à armature textile ou métallique, pour applications à jet d'eau à haute et ultra haute pression — Spécifications — Amendement 1",2019-02-27,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[75386],"['en','fr']",1,

64802,IS,,ISO 19396-1:2017,Paints and varnishes — Determination of pH value — Part 1: pH electrodes with glass membrane,Peintures et vernis — Détermination de la valeur de pH — Partie 1: Électrodes de pH à membrane en verre,2017-08-11,1,['87.040'],ISO/TC 35/SC 9,9599,,[87268],"['en','fr']",15,<p>ISO 19396-1:2017 specifies a method for laboratory measurement of the pH value of polymer dispersions and coating materials using pH electrodes with a glass membrane. ISO 19396‑2 specifies a method for measuring the pH value using pH electrodes with ion-sensitive field-effect transistor (ISFET) technology.</p>

64803,IS,,ISO 19396-2:2017,Paints and varnishes — Determination of pH value — Part 2: pH electrodes with ISFET technology,Peintures et vernis — Détermination de la valeur de pH — Partie 2: Électrodes de pH dotées de la technologie ISFET,2017-08-11,1,['87.040'],ISO/TC 35/SC 9,9599,,[87269],"['en','fr']",13,<p>ISO 19396-2:2017 specifies a method for measuring the pH value of dispersions and coating materials using pH electrodes with ion-sensitive field-effect transistor (ISFET) technology. ISO 19396‑1 specifies a method for measuring the pH value using pH electrodes with a glass membrane.</p>

4044,IS,,ISO 194:1981,Plastics — List of equivalent terms,Plastiques — Liste des termes équivalents,1981-03-01,1,"['83.080.01','01.040.83']",ISO/TC 61,9599,,[4501],"['en','fr','ru']",58,

4045,IS,Add,ISO 194:1981/Add 1:1983,Plastics — List of equivalent terms — Addendum 1,Plastiques — Liste des termes équivalents — Additif 1,1983-12-01,1,"['83.080.01','01.040.83']",ISO/TC 61/SC 1,9599,,[4501],"['en','fr','ru']",10,

4046,IS,Add,ISO 194:1981/Add 2:1983,Plastics — List of equivalent terms — Addendum 2,Plastiques — Liste des termes équivalents — Additif 2,1983-12-01,1,"['83.080.01','01.040.83']",ISO/TC 61/SC 1,9599,,[4501],"['en','fr','ru']",9,

4047,IS,Add,ISO 194:1981/Add 4:1981,Plastics — List of equivalent terms — Addendum 4,Plastiques — Liste des termes équivalents — Additif 4,1981-10-01,1,"['83.080.01','01.040.83']",ISO/TC 61,9599,,[4501],"['en','fr','ru']",10,

4048,IS,Add,ISO 194:1981/Add 5:1983,Plastics — List of equivalent terms — Addendum 5,Plastiques — Liste des termes équivalents — Additif 5,1983-12-01,1,"['83.080.01','01.040.83']",ISO/TC 61/SC 1,9599,,[4501],"['en','fr','ru']",12,

6635,IS,,ISO 1940-1:1986,Mechanical vibration — Balance quality requirements of rigid rotors — Part 1: Determination of permissible residual unbalance,Vibrations mécaniques — Exigences en matière de qualité dans l'équilibrage des rotors rigides — Partie 1: Détermination du balourd résiduel admissible,1986-09-11,1,['21.120.40'],ISO/TC 108,9599,[6634],[27092],"['en','fr']",15,"<p>Specifies a representation in one or two planes; methods for determining, for allocation to the correction planes; for identifying the state of a rotor by measurement; a summary of errors associated with the identification. Gives recommendations according to type, mass and maximum service speed. Is not intended to ser

27092,IS,,ISO 1940-1:2003,Mechanical vibration — Balance quality requirements for rotors in a constant (rigid) state — Part 1: Specification and verification of balance tolerances,Vibrations mécaniques — Exigences en matière de qualité dans l'équilibrage pour les rotors en état (rigide) constant — Partie 1: Spécifications et vérification des tolérances d'équilibrage,2003-09-08,2,['21.120.40'],ISO/TC 108/SC 2,9599,[6635],"[57709,54074]","['en','fr']",28,"<p>ISO 1940-1:2003 gives specifications for rotors in a constant (rigid) state. It specifies balance tolerances, the necessary number of correction planes, and methods for verifying the residual unbalance.</p><p>Recommendations are also given

41364,IS,Cor,ISO 1940-1:2003/Cor 1:2005,Mechanical vibration — Balance quality requirements for rotors in a constant (rigid) state — Part 1: Specification and verification of balance tolerances — Technical Corrigendum 1,Vibrations mécaniques — Exigences en matière de qualité dans l'équilibrage pour les rotors en état (rigide) constant — Partie 1: Spécifications et vérification des tolérances d'équilibrage — Rectificatif technique 1,2005-01-04,2,['21.120.40'],ISO/TC 108/SC 2,9599,,"[57709,54074]","['en','fr']",2,

6634,IS,,ISO 1940:1973,Balance quality of rotating rigid bodies,Qualité d'équilibrage des corps rigides en rotation,1973-05-01,1,['21.120.40'],ISO/TC 108,9599,,[6635],"['en','fr']",9,

6636,IS,,ISO 1940-2:1997,Mechanical vibration — Balance quality requirements of rigid rotors — Part 2: Balance errors,Vibrations mécaniques — Exigences en matière de qualité dans l'équilibrage des rotors rigides — Partie 2: Défauts d'équilibrage,1997-06-19,1,['21.120.40'],ISO/TC 108/SC 2,9599,,"[35621,50430]","['en','fr']",16,

64808,IS,,ISO 19403-1:2017,Paints and varnishes — Wettability — Part 1: Terminology and general principles,Peintures et vernis — Mouillabilité — Partie 1: Terminologie et principes généraux,2017-06-28,1,"['01.040.87','87.040']",ISO/TC 35/SC 9,9599,,[81414],"['en','fr']",9,"<p>The ISO 19403 series specifies optical test methods</p><p>- for the measurement of the contact angle,</p><p>- for the determination of the free surface energy of a solid surface, including the polar and dispersive fractions,</p><p>- for the determination of the surface tension of liquids, including the polar and dispersive fractions, and</p><p>- for the checking of the measurement arrangement with re

64809,IS,,ISO 19403-2:2017,Paints and varnishes — Wettability — Part 2: Determination of the surface free energy of solid surfaces by measuring the contact angle,Peintures et vernis — Mouillabilité — Partie 2: Détermination de l'énergie libre de surface des surfaces solides par la mesure de l'angle de contact,2017-06-28,1,['01.040.87'],ISO/TC 35/SC 9,9599,,[87262],"['en','fr']",14,"<p>ISO 19403-2:2017 specifies a test method to measure the contact angle for the determination of the surface free energy of a solid surface. The method can be applied for the characterization of substrates and coatings.</p><p>NOTE 1 For the determination of the surface free energy of polymers and coatings, eit

64810,IS,,ISO 19403-3:2017,Paints and varnishes — Wettability — Part 3: Determination of the surface tension of liquids using the pendant drop method,Peintures et vernis — Mouillabilité — Partie 3: Détermination de la tension superficielle des liquides par la méthode de la goutte pendante,2017-06-28,1,['01.040.87'],ISO/TC 35/SC 9,9599,,[87263],"['en','fr']",12,"<p>ISO 19403-3:2017 specifies a test method to measure the surface tension of liquids with an optical method using the pendant drop. The method can be applied for the characterization of liquid coating materials. The applicability can be restricted for liquids with non-Newtonian rheology[1].</p><p>NOTE For other methods to deter

64811,IS,,ISO 19403-4:2017,Paints and varnishes — Wettability — Part 4: Determination of the polar and dispersive fractions of the surface tension of liquids from an interfacial tension,Peintures et vernis — Mouillabilité — Partie 4: Détermination des fractions polaire et dispersive de la tension superficielle des liquides à partir de la tension interfaciale,2017-06-28,1,['01.040.87'],ISO/TC 35/SC 9,9599,,[87264],"['en','fr']",8,"<p>ISO 19403-4:2017 specifies a test method to determine the polar and dispersive fraction of the surface tension of liquids with optical methods. The method can be applied for the characterization of liquid coating materials, especially when drying effects occur du

64812,IS,,ISO 19403-5:2017,Paints and varnishes — Wettability — Part 5: Determination of the polar and dispersive fractions of the surface tension of liquids from contact angles measurements on a solid with only a disperse contribution to its surface energy,Peintures et vernis — Mouillabilité — Partie 5: Détermination des fractions polaire et dispersive de la tension superficielle des liquides à partir de mesurages de l'angle de contact avec un solide n'ayant qu'une contribution de dispersion à son énergie de surface,2017-06-28,1,['01.040.87'],ISO/TC 35/SC 9,9599,,[87265],"['en','fr']",6,<p>ISO 19403-5:2017 specifies a test method to determine the polar and dispersive fractions of the surfac

64813,IS,,ISO 19403-6:2017,Paints and varnishes — Wettability — Part 6: Measurement of dynamic contact angle,Peintures et vernis — Mouillabilité — Partie 6: Mesurage de l'angle de contact dynamique,2017-06-28,1,['01.040.87'],ISO/TC 35/SC 9,9599,,[87266],"['en','fr']",11,"<p>ISO 19403-6:2017 specifies a method to measure the dynamic contact angle with an optical method. The advancing and the receding angles are determined.</p><p>By means of this defined measurement, the wetting and dewetting properties can be characterized. It can also be concluded on the morphological and chemical homogeneity of interfaces.</p>"

64814,IS,,ISO 19403-7:2017,Paints and varnishes — Wettability — Part 7: Measurement of the contact angle on a tilt stage (roll-off angle),Peintures et vernis — Mouillabilité — Partie 7: Mesurage de l'angle de contact sur un plan incliné (angle de roulement),2017-06-28,1,['01.040.87'],ISO/TC 35/SC 9,9599,,[87267],"['en','fr']",13,"<p>ISO 19403-7:2017 specifies a method for the dynamic measurement of the roll-off angle of a liquid drop on a solid surface. From the dynamic measurement, the advancing and receding angles of the drop rolling off can also be determined. The roll-off angle plays a role when evaluating, for example, easy-to-clean or anti-adherent surfaces.</p>"

6646,IS,,ISO 1942-1:1977,Withdrawal of ISO 1942/1-1977,Annulation de l'ISO 1942/1-1977,1977-10-01,3,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,[6638],"['en','fr']",3,

6647,IS,,ISO 1942-1:1989,Dental vocabulary — Part 1: General and clinical terms,Vocabulaire de l'art dentaire — Partie 1: Termes généraux et cliniques,1989-06-29,4,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,"[6639,6643,6640,6644,6641,6642,6638]","[50179,22522]","['en','fr']",15,<p>This standard is intended to provide accepted definitions for a number of terms used in dentistry that could prove useful for the comprehension of documents and to improve communication. It defines 130 general and clinical terms. Together with the other four parts it constitutes a technical revision of the first edition of this standard.</p>

6649,IS,Amd,ISO 1942-1:1989/Amd 1:1992,Dental vocabulary — Part 1: General and clinical terms — Amendment 1,Vocabulaire de l'art dentaire — Partie 1: Termes généraux et cliniques — Amendement 1,1992-03-12,4,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[50179,22522]","['en','fr']",2,<p>Gives in numerical sequence the terms from 1.133 up to and including 1.180 in English and French.</p>

6650,IS,Amd,ISO 1942-1:1989/Amd 2:1992,Dental vocabulary — Part 1: General and clinical terms — Amendment 2,Vocabulaire de l'art dentaire — Partie 1: Termes généraux et cliniques — Amendement 2,1992-07-30,4,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[50179,22522]","['en','fr']",1,"<p>Adds the terms 1.181 (articulating paper), 1.182 (baseplate), 1.183 (orthodontic appliance), 1.184 (removable orthodontic appliance), and 1.185 (fixed orthodontic appliance).</p>"

6651,IS,Amd,ISO 1942-1:1989/Amd 3:1993,Dental vocabulary — Part 1: General and clinical terms — Amendment 3,Vocabulaire de l'art dentaire — Partie 1: Termes généraux et cliniques — Amendement 3,1993-12-02,4,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[50179,22522]","['en','fr']",1,<p>Adds 7 new terms (including definitions) in English and French.</p>

20658,IS,Amd,ISO 1942-1:1989/Amd 5:1993,Dental vocabulary — Part 1: General and clinical terms — Amendment 5,Vocabulaire de l'art dentaire — Partie 1: Termes généraux et cliniques — Amendement 5,1993-04-08,4,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[50179,22522]","['en','fr']",1,"<p>Adds the terms 1.196 to 1.208 (biodegradation, biodegradable, bioacceptability, bioacceptable, biocompatibility, biocompatible, positive biocompatibility, biopositive, biomaterial, dental biomaterial, sterilization, disinfection, decontamination).</p>"

6638,IS,,ISO 1942:1983,Dental vocabulary,Vocabulaire de l'art dentaire,1983-03-01,1,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,"[6658,6663,6646,6653]","[6654,6647,6659,6667,6664]","['en','fr']",41,

6639,IS,Add,ISO 1942:1983/Add 1:1983,Dental vocabulary — Addendum 1,Vocabulaire de l'art dentaire — Additif 1,1983-09-01,1,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[6654,6647,6659,6667,6664]","['en','fr']",3,

6640,IS,Add,ISO 1942:1983/Add 2:1983,Dental vocabulary — Addendum 2,Vocabulaire de l'art dentaire — Additif 2,1983-12-01,1,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[6654,6647,6659,6667,6664]","['en','fr']",1,

6641,IS,Add,ISO 1942:1983/Add 3:1983,Dental vocabulary — Addendum 3,Vocabulaire de l'art dentaire — Additif 3,1983-12-01,1,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[6654,6647,6659,6667,6664]",['en'],1,

6642,IS,Add,ISO 1942:1983/Add 4:1984,Dental vocabulary — Addendum 4,Vocabulaire de l'art dentaire — Additif 4,1984-08-01,1,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[6654,6647,6659,6667,6664]","['en','fr']",5,

6643,IS,Add,ISO 1942:1983/Add 5:1985,Dental vocabulary — Addendum 5,Vocabulaire de l'art dentaire — Additif 5,1985-08-29,1,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[6654,6647,6659,6667,6664]",,,

6644,IS,Add,ISO 1942:1983/Add 6:1985,Dental vocabulary — Addendum 6,Vocabulaire de l'art dentaire — Additif 6,1985-07-11,1,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,"[6654,6647,6659,6667,6664]",,,

6653,IS,,ISO 1942-2:1977,Withdrawal of ISO 1942/2-1977,Annulation de l'ISO 1942/2-1977,1977-10-01,2,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,[6638],"['en','fr']",5,

6654,IS,,ISO 1942-2:1989,Dental vocabulary — Part 2: Dental materials,Vocabulaire de l'art dentaire — Partie 2: Produits dentaires,1989-06-29,3,"['11.060.10','01.040.11']",ISO/TC 106/SC 3,9599,"[6639,6643,6640,6644,6641,6642,6638]","[22523,50179]","['en','fr']",16,<p>Intended to provide accepted definitions for a number of terms used in dentistry that could prove useful for the comprehension of documents and to improve communication. It defines 121 terms of dental materials. Together with the other four parts it constitutes a technical revision of the first edition of this standard.</p>

6655,IS,Amd,ISO 1942-2:1989/Amd 1:1992,Dental vocabulary — Part 2: Dental materials — Amendment 1,Vocabulaire de l'art dentaire — Partie 2: Produits dentaires — Amendement 1,1992-03-12,3,"['11.060.10','01.040.11']",ISO/TC 106/SC 3,9599,,"[22523,50179]","['en','fr']",2,<p>Gives in numerical sequence the terms from 2.122 up to and including 2.145 in English and French.</p>

6656,IS,Amd,ISO 1942-2:1989/Amd 2:1992,Dental vocabulary — Part 2: Dental materials — Amendment 2,Vocabulaire de l'art dentaire — Partie 2: Produits dentaires — Amendement 2,1992-07-30,3,"['11.060.10','01.040.11']",ISO/TC 106/SC 3,9599,,"[22523,50179]","['en','fr']",1,"<p>Adds the terms 2.146 (contact indicating material), 2.147 (fluoride gel), 2.148 (pit and fissure sealant), and 2.149 (opaquer).</p>"

50179,IS,,ISO 1942:2009,Dentistry — Vocabulary,Médecine bucco-dentaire — Vocabulaire,2009-12-03,2,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,"[6651,6659,6660,6667,6654,6661,6655,6647,20658,6656,6649,6664,6650,6665]",[72249],"['en','fr']",80,"<p>ISO 1942:2008 provides definitions for a number of concepts specific to dentistry in the interest of facilitating development and comprehension of standards, and to improve communication with the <i>Fédération Dentaire Internationale,</i> the World Health Organization and other interested organizations.</p><p>Annex A to ISO 1942:2008 provides additional information that can be helpful to users of the document.</p>"

6658,IS,,ISO 1942-3:1977,Withdrawal of ISO 1942/3-1977,Annulation de l'ISO 1942/3-1977,1977-10-01,2,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,[6638],"['en','fr']",10,

6659,IS,,ISO 1942-3:1989,Dental vocabulary — Part 3: Dental instruments,Vocabulaire de l'art dentaire — Partie 3: Instruments dentaires,1989-06-29,3,"['11.060.20','01.040.11']",ISO/TC 106/SC 3,9599,"[6639,6643,6640,6644,6641,6642,6638]","[22524,50179]","['en','fr']",26,<p>Intended to provide accepted definitions for a number of terms used in dentistry that could prove useful for the comprehension of documents and to improve communication. It defines 279 terms of dental instruments. Together with the other four parts it constitutes a technical revision of the first edition of this standard.</p>

6660,IS,Amd,ISO 1942-3:1989/Amd 1:1992,Dental vocabulary — Part 3: Dental instruments — Amendment 1,Vocabulaire de l'art dentaire — Partie 3: Instruments dentaires — Amendement 1,1992-03-12,3,"['11.060.20','01.040.11']",ISO/TC 106/SC 3,9599,,"[22524,50179]","['en','fr']",1,<p>Gives in numerical sequence the terms from 3.280 up to and including 3.921 in English and French.</p>

6661,IS,Amd,ISO 1942-3:1989/Amd 2:1992,Dental vocabulary — Part 3: Dental instruments — Amendment 2,Vocabulaire de l'art dentaire — Partie 3: Instruments dentaires — Amendement 2,1992-07-29,3,"['11.060.20','01.040.11']",ISO/TC 106/SC 3,9599,,"[22524,50179]","['en','fr']",1,"<p>5 Adds the 9 terms 3.292 to 3.300: endodontic absorbent point (paper point), endodontic obturating point, endodontic gutta-percha point, endodontic silver point, endodontic polymeric point, band pusher, band-removing pliers, retractor, and dental amalgam carrier.</p>"

6663,IS,,ISO 1942-4:1976,Withdrawal of ISO 1942/4-1976,Annulation de l'ISO 1942/4-1976,1976-11-01,1,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,,[6638],"['en','fr']",3,

6664,IS,,ISO 1942-4:1989,Dental vocabulary — Part 4: Dental equipment,Vocabulaire de l'art dentaire — Partie 4: Matériel dentaire,1989-06-29,2,"['11.060.20','01.040.11']",ISO/TC 106/SC 3,9599,"[6639,6643,6640,6644,6641,6642,6638]","[50179,22525]","['en','fr']",9,<p>Intended to provide accepted definitions for a number of terms used in dentistry that could prove useful for the comprehension of documents and to improve communication. It defines 53 terms of dental equipment and illumination. Together with the other four parts it constitutes a technical revision of the first edition of this standard.</p>

6665,IS,Amd,ISO 1942-4:1989/Amd 1:1992,Dental vocabulary — Part 4: Dental equipment — Amendment 1,Vocabulaire de l'art dentaire — Partie 4: Matériel dentaire — Amendement 1,1992-07-29,2,"['11.060.20','01.040.11']",ISO/TC 106/SC 3,9599,,"[50179,22525]","['en','fr']",1,"<p>Adds the terms 4.054 ((dental amalgam) alloy dispenser), 4.055 ((dental) mercury dispenser), 4.056 (dental amalgamator), 4.057 (X-ray film dispenser), and 4.058 (impression tray).</p>"

6667,IS,,ISO 1942-5:1989,Dental vocabulary — Part 5: Terms associated with testing,Vocabulaire de l'art dentaire — Partie 5: Termes associés aux essais,1989-06-29,2,"['11.060.01','01.040.11']",ISO/TC 106/SC 3,9599,"[6639,6643,6640,6644,6641,6642,6638]","[22526,50179]","['en','fr']",11,<p>Intended to provide accepted definitions for a number of terms used in dentistry that could prove useful for the comprehension of documents and to improve communication. It defines 89 terms associated with testing. Together with the other four parts it constitutes a technical revision of the first edition of this standard.</p>

64890,IS,,ISO 19430:2016,Particle size analysis — Particle tracking analysis (PTA) method,Analyse granulométrique — Méthode d'analyse de suivi de particule (PTA),2016-12-15,1,['19.120'],ISO/TC 24/SC 4,9599,,[82473],['en'],25,"<p>ISO 19430:2016 describes the evaluation of the number?based particle size distribution in liquid dispersions (solid, liquid or gaseous particles suspended in liquids) using the particle tracking analysis method for diffusion velocity measurements.</p>"

39090,IS,,ISO 19432:2006,"Building construction machinery and equipment — Portable, hand-held, internal combustion engine driven cut-off machines — Safety requirements and testing","Machines et matériels pour la construction des bâtiments — Tronçonneuses à disque, portatives, à moteur à combustion interne — Exigences de sécurité et essais",2006-03-17,1,['91.220'],ISO/TC 195,9599,,[52418],"['en','fr']",37,"<p>ISO 19432:2006 specifies safety requirements and their verification by testing for the design and construction of portable, hand-held, internal combustion engine driven, cut-off machines, intended to be used by a single operator in the cutting of construction materials such as asphalt, c

52418,IS,,ISO 19432:2012,"Building construction machinery and equipment — Portable, hand-held, internal combustion engine driven cut-off machines — Safety requirements","Machines et matériels pour la construction des bâtiments — Tronçonneuses à disque, portatives, à moteur à combustion interne — Exigences de sécurité",2012-07-11,2,['91.220'],ISO/TC 195,9599,[39090],[68956],"['en','fr']",43,"<p>ISO 19432:2012 specifies safety requirements and measures for their verification for the design and construction of portable, hand-held, internal combustion engine driven, cut-off machines, intended to be used by a single operator in the cutting of construction materials, such as asphalt, concrete, sto

33831,IS,,ISO 19438:2003,Diesel fuel and petrol filters for internal combustion engines — Filtration efficiency using particle counting and contaminant retention capacity,"Filtres à carburant, essence ou diesel, pour moteurs à combustion interne — Efficacité de filtration par comptage des particules et capacité de rétention",2003-11-04,1,['43.060.40'],ISO/TC 22/SC 34,9599,[35892],[82268],['en'],38,"<p>ISO 19438:2003 specifies a multi-pass filtration test, with continuous contaminant injection and using the on-line particle counting method, for evaluating the performance of fuel filters for internal combustion engines submitted to a constant flow rate of test liquid. The test procedure determ

33834,IS,,ISO 19440:2007,Enterprise integration — Constructs for enterprise modelling,Entreprise intégrée — Constructions pour la modélisation d'entreprise,2007-11-19,1,['25.040.40'],ISO/TC 184/SC 5,9599,,[74491],"['en','fr']",111,"<p>ISO 19440:2007 specifies the characteristics of the core constructs necessary for computer-supported modelling of enterprises conforming to ISO 19439.</p><p>ISO 19440:2007 focuses on, but is not restricted to, the computer integration of the information aspects of manufacturing, including the management and control technology and the required human tasks. It does not specify how these core constructs for model-based operations are to be implemented and, in part

64911,IS,,ISO 19444-1:2016,Document management — XML Forms Data Format — Part 1: Use of ISO 32000-2 (XFDF 3.0),Gestion de documents — Format de Données des Formulaires XML — Partie 1: Utilisation de l'ISO 32000-2 (XFDF 3.0),2016-11-30,1,['35.240.30'],ISO/TC 171/SC 2,9599,,[74272],['en'],67,"<p>ISO 19444-1:2016 specifies an XML format for representing forms data and annotations in the Portable Document Format, ISO 32000-2 (PDF 2.0).</p><p>ISO 19444-1:2016 does not change or add any definitions for any components of ISO 32000-2.</p>"

64912,IS,,ISO 19445:2016,Graphic technology — Metadata for graphic arts workflow — XMP metadata for image and document proofing,Technologie graphique — Métadonnées pour le flux de travail des arts graphiques — Métadonnées XMP pour la relecture de document et d'image,2016-05-27,1,['35.240.30'],ISO/TC 130,9599,,[84132],['en'],9,"<p>ISO 19445:2016 specifies the set of metadata to be used to communicate the approval status, proof preparation and viewing parameters for images and documents that are used in the graphic arts print production workflow.</p>"

6672,IS,,ISO 1948:1973,Photography — Front lens barrels up to 100 mm — Dimensions important to the connection of auxiliaries,Photographie,1973-10-01,1,['37.040.10'],ISO/TC 42,9599,,[6673],"['en','fr']",1,

6674,IS,,ISO 1949:1973,Design requirements for aircraft electrical plug and socket connectors,Caractéristiques des connecteurs électriques pour aéronefs,1973-05-01,1,['49.060'],ISO/TC 20/SC 1,9599,,[6675],"['en','fr']",10,

65138,IS,,ISO 19490:2017,Dentistry — Sinus membrane elevator,Médecine bucco-dentaire — Élévateur de membrane sinusienne,2017-05-23,1,['11.060.25'],ISO/TC 106/SC 4,9599,,[85770],"['en','fr']",5,<p>ISO 19490:2017 specifies requirements and their test methods for sinus membrane elevators used during the placement of dental implants for sinus floor lifting. It also specifies the requirements for their marking and labelling.</p>

42442,IS,,ISO 19499:2007,Mechanical vibration — Balancing — Guidance on the use and application of balancing standards,Vibrations mécaniques — Équilibrage — Lignes directrices pour l'utilisation et l'application de normes d'équilibrage,2007-07-09,1,['21.120.40'],ISO/TC 108/SC 2,9599,,"[73726,57708]",['en'],35,<p>ISO 19499:2007 provides an introduction to balancing and directs the user through the available International Standards associated with rotor balancing. It gives guidance on which of these standards should be used. Individual procedures are not included as these will be found in the appropriate International Standards.</p>

6676,IS,,ISO 1950:1974,"Aircraft — Identification of servicing, maintenance, ground handling and safety/hazard points","Aéronefs — Identification des points d'alimentation au sol, des points d'entretien et de manutention, et des points danger/sécurité à bord",1974-05-01,1,['49.100'],ISO/TC 20/SC 9,9599,,[1639],"['en','fr']",7,"<p>Includes the symbols, and their positions and sizes, to be used for the marking of these points, to enable them to be quickly identified during intermediate stops an scheduled flights and during scheduled maintenance checks. Requirements for warning markings, to prevent damage to equipment or injury to personnel, and for the marking of batches are also included.</p>

6677,IS,,ISO 1951:1973,Lexicographical symbols particularly for use in classified defining vocabularies,Symboles lexicographiques particulièrement pour l'emploi dans les vocabulaires systématiques à définitions,1973-11-01,1,['01.020'],ISO/TC 37,9599,,[6678],"['en','fr']",30,

6678,IS,,ISO 1951:1997,Lexicographical symbols and typographical conventions for use in terminography,Symboles lexicographiques et conventions typographiques à utiliser en terminographie,1997-09-25,2,"['01.080.99','01.020']",ISO/TC 37/SC 2,9599,[6677],[36609],"['en','fr']",9,

36609,IS,,ISO 1951:2007,"Presentation/representation of entries in dictionaries — Requirements, recommendations and information","Présentation/représentation des entrées dans les dictionnaires — Exigences, recommandations et information",2007-02-08,3,"['01.080.99','01.020']",ISO/TC 37/SC 2,9599,[6678],[84863],"['en','fr']",77,"<p>ISO 1951:2007 deals with monolingual and multilingual, general and specialized dictionaries. It specifies a formal generic structure independent of the publishing media and it proposes means of presenting entries in print and electronic dictionaries. The relationship between the formal structure and the presentation of entries used by publishers and read by users is

6679,IS,,ISO 1952:1976,Brown coals and lignites — Method of extraction for the determination of sodium and potassium soluble in dilute hydrochloric acid,Charbons bruns et lignites — Méthode d'extraction en vue des dosages du sodium et du potassium solubles dans l'acide chlorhydrique dilué,1976-06-01,1,['73.040'],ISO/TC 27,9599,,"[33582,41590]","['en','fr']",2,"<p>The sample of brown coal or lignite is extracted with boiling 0,005 N hydrochloric acid and the extract centrifuged. The sodium and potassium in solution are determined by any precise analytical method (for example, gravimetric method or flame photometric method).</p>"

41590,IS,,ISO 1952:2008,Solid mineral fuels — Determination of extractable metals in dilute hydrochloric acid,Combustibles minéraux solides — Détermination des métaux extractibles dans l'acide chlorhydrique dilué,2008-08-18,2,['73.040'],ISO/TC 27/SC 5,9599,[6679],[86990],['en'],6,"<p>ISO 1952:2008 describes the extraction from solid mineral fuels by dilute hydrochloric acid and determination of extractable sodium, potassium, calcium, iron and magnesium.</p>"

6680,IS,,ISO 1953:1972,Hard coals — Size analysis,Charbon — Analyse granulométrique,1972-08-01,1,['73.040'],ISO/TC 27,9599,,[6681],"['en','fr']",16,

6681,IS,,ISO 1953:1994,Hard coal — Size analysis by sieving,Houille — Analyse granulométrique par tamisage,1994-07-14,2,['73.040'],ISO/TC 27/SC 1,9599,[6680],[63664],"['en','fr']",12,"<p>Specifies reference methods for the size analysis of coal by manual sieving (wet or dry), using test sieves of aperture sizes between 125 mm and 45 µm. A guide to sampling is given in annex A and notes on the use of mechanical sieving are given in annex B. Is applicable to all hard coals. Is not applicable to coke or other manufactured fuels. In the case of pulverized coal, the methods described will determine only the percentage of oversize.</p>"

63664,IS,,ISO 1953:2015,Hard coal — Size analysis by sieving,Houille — Analyse granulométrique par tamisage,2015-11-10,3,['73.040'],ISO/TC 27/SC 1,9599,[6681],[87991],['en'],13,"<p>ISO 1953:2015 specifies reference methods for the size analysis of coal by manual sieving (wet or dry), using test sieves of aperture sizes between 125 mm and 45 μm. A guide to sampling is given in Annex A.</p><p>This International Standard is applicable to all hard coals. It is not applicable to coke or other manufactured fuels.</p><p>In the case of pulverized coal which has been ground so that a high proportion passes through the test sieve of smallest aperture size, the methods described in this International S

6682,IS,,ISO 1954:1999,Plywood — Tolerances on dimensions,Contreplaqué — Tolérances sur dimensions,1999-04-15,1,['79.060.10'],ISO/TC 89/SC 3,9599,,[61093],"['en','fr']",2,

6686,IS,,ISO 1957:1973,Machine-made textile floor coverings — Sampling and cutting specimens for physical tests of machine made textile floor coverings,Revêtements de sol textiles fabriqués à la machine — Échantillonnage et prélèvement des éprouvettes en vue des essais physiques,1973-09-01,1,['97.150'],ISO/TC 38,9599,,[6687],"['en','fr']",2,

6687,IS,,ISO 1957:1986,Machine-made textile floor coverings — Sampling and cutting specimens for physical tests,Revêtements de sol textiles fabriqués à la machine — Échantillonnage et prélèvement des éprouvettes en vue des essais physiques,1986-06-19,2,['97.150'],ISO/TC 219,9599,[6686],[30383],"['en','fr']",2,

6688,IS,,ISO 1958:1973,Textile floor coverings — Determination of mass of total pile yarn per unit area,Tapis-moquettes — Détermination de la masse totale du fil de velours par unité de surface,1973-09-01,1,['97.150'],ISO/TC 219,9599,,[15793],"['en','fr']",2,