Withdrawn and superseded ISO standards — page 62 of 246

51448,IS,,ISO 17386:2010,Transport information and control systems — Manoeuvring Aids for Low Speed Operation (MALSO) — Performance requirements and test procedures,Systèmes d'information et de commande des transports — Aides à la conduite pour manoeuvre à vitesse réduite (MALSO) — Exigences de performance et modes opératoires,2010-03-10,2,['43.040.15'],ISO/TC 204,9599,[30634],[82952],['en'],21,"<p>ISO 17386:2010 addresses light-duty vehicles, e.g. passenger cars, pick-up trucks, light vans and sport utility vehicles (motorcycles excluded) equipped with MALSO (Manoeuvring Aids for Low Speed Operation) systems. It specifies minimum functionality requirements which the driver can generally exp

43654,IS,,ISO 17387:2008,Intelligent transport systems — Lane change decision aid systems (LCDAS) — Performance requirements and test procedures,Systèmes intelligents de transport — Systèmes d'aide à la décision de changement de voie — Exigences de performances et méthodes d'essai,2008-04-16,1,"['35.240.60','03.220.20']",ISO/TC 204,9599,,[88222],['en'],49,"<p>ISO 17387:2008 specifies system requirements and test methods for Lane Change Decision Aid Systems (LCDAS). LCDAS are fundamentally intended to warn the driver of the subject vehicle against potential collisions with vehicles to the side and/or to the rear of the subject vehicle, and moving in the same direction as the subject vehicle d

6359,IS,,ISO 1739:1975,Butter — Determination of the refractive index of the fat (Reference method),Beurre — Détermination de l'indice de réfraction de la matière grasse (Méthode de référence),1975-12-01,1,['67.100.20'],ISO/TC 34/SC 5,9599,,[44508],"['en','fr']",1,"<p>Describes a method of measurement which uses a refractometer with a scale graduated in refractive index units to the third decimal place and having prisms heated by means of a circulating liquid at 40 degrees centigrade, the temperature being thermostatically controlled to within +/- 0.1 degrees centigrade. A sodium vapour lamp shall be used as a light source.</p>"

44802,IS,,ISO 17396:2014,"Synchronous belt drives — Metric pitch, trapezoidal profile systems T and AT, belts and pulleys","Transmissions synchrones par courroies — Pas métrique, poulies et courroies dentées à dents trapézoïdales de profil T ou AT",2014-01-16,1,['21.220.10'],ISO/TC 41/SC 4,9599,,[70627],['en'],18,"<p>ISO 17396:2014 specifies the principal characteristics of synchronous endless and open belts and pulleys of the profile systems T and AT for use in synchronous belt drives for mechanical power transmission and where positive indexing or synchronization can be required.</p><p/><p>The principal belt and pulley characteristics include</p><ul><li>nominal belt tooth dimensions,</li><

70627,IS,,ISO 17396:2017,Synchronous belt drives — Metric pitch — Tooth profiles T and AT endless and open ended belts and pulleys,Transmissions synchrones par courroies — Pas métrique — Poulies et courroies dentées sans fin ou à bout libre à dents de profil T ou AT,2017-11-24,2,['21.220.10'],ISO/TC 41/SC 4,9599,[44802],[88593],['en'],18,"<p>ISO 17396:2017 specifies the principal characteristics of synchronous endless and open belts and pulleys of the profile systems T and AT for use in synchronous belt drives for mechanical power transmission and where positive indexing or synchronization can be required.</p><p>NOTE Synchronous belt drives have been known by various titles in the past

4008,IS,,ISO 174:1974,Plastics — Homopolymer and copolymer resins of vinyl chloride — Determination of viscosity number in dilute solution,Plastiques — Résines d'homopolymères et de copolymères de chlorure de vinyle — Détermination de l'indice de viscosité en solution diluée,1974-08-01,1,['83.080.20'],ISO/TC 61,9599,,[6228],"['en','fr']",4,

6360,IS,,ISO 1740:1980,Butter — Determination of the acid value of the fat (Reference method),Beurre — Détermination de l'indice d'acide de la matière grasse (Méthode de référence),1980-02-01,1,['67.100.20'],ISO/TC 34/SC 5,9599,,[6361],"['en','fr']",2,

6361,IS,,ISO 1740:1991,Milk fat products and butter — Determination of fat acidity (Reference method),Produits à matière grasse laitière et beurre — Détermination de l'acidité de la matière grasse (Méthode de référence),1991-07-18,2,"['67.100.20','67.100.10']",ISO/TC 34/SC 5,9599,[6360],[40462],"['en','fr']",5,"<p>Specifies a method for the determination of the acidity of the fat contained in milk fat products and in butter. Describes the apparatus, the procedure, the reagents to be used, and the expression of results. This second edition cancels and replaces the first edition (1980). Annex A is for information only.</p>"

33038,IS,,ISO 17401:2004,Space systems — Spacecraft interface requirements document for launch vehicle services,Systèmes spatiaux — Document d'exigences d'interface du véhicule spatial vis-à-vis du service de lancement,2004-06-18,1,['49.140'],ISO/TC 20/SC 14,9599,,[78976],"['en','fr']",21,"<p>ISO 17401:2004 provides spacecraft (SC) organizations with the general format for presenting the interface requirement document (IRD) for launch vehicle services. The IRD provides a list of the major technical requirements spacecraft agencies provide to launch vehicle (LV) agencies when submitting an application for launch services.</p><p>ISO 17401:2004 is applicable to all existing commercial LV and re

59633,IS,,ISO 17405:2014,"Non-destructive testing — Ultrasonic testing — Technique of testing claddings produced by welding, rolling and explosion","Essais non destructifs — Essais par ultrasons — Technique d'essai des placages produits par soudage, laminage et explosion",2014-07-17,1,['19.100'],ISO/TC 44/SC 5,9599,,[83006],"['en','fr','ru']",11,"<p>ISO 17405:2014 specifies the techniques for manual ultrasonic testing of claddings on steel applied by welding, rolling, and explosion using single-element or dual-element probes. The test is intended to cover detection of two-dimensional or three-dimensional discontinuities in the cladding and in the region of the interface.</p><p>ISO 17405:2014

68491,IS,,ISO 17409:2015,Electrically propelled road vehicles — Connection to an external electric power supply — Safety requirements,Véhicules routiers à propulsion électrique — Connexion à une alimentation électrique externe — Exigences de sécurité,2015-10-23,1,['43.120'],ISO/TC 22/SC 37,9599,,[72880],"['en','fr']",23,"<p>ISO 17409:2015 specifies electric safety requirements for conductive connections of electrically propelled road vehicles to an external electric power supply using a plug or vehicle inlet.</p><p>It applies to electrically propelled road vehicles with voltage class B electric circuits. In general, it may apply to motorcycles and mopeds if no dedicated standards for these v

72880,IS,,ISO 17409:2020,Electrically propelled road vehicles — Conductive power transfer — Safety requirements,Véhicules routiers à propulsion électrique — Transfert de puissance par conduction — Exigences de sécurité,2020-02-26,2,['43.120'],ISO/TC 22/SC 37,9599,[68491],[81345],"['en','fr']",41,"<p>This document specifies electric safety requirements for conductive connection of electrically propelled road vehicles to external electric circuits. External electric circuits include external electric power supplies and external electric loads. This document provides requirements for the charging modes 2, 3, 4, as defined in IEC 61851-1, and reverse power transfer. For mode 4, this document pro

30649,IS,,ISO 17410:2001,Microbiology of food and animal feeding stuffs — Horizontal method for the enumeration of psychrotrophic microorganisms,Microbiologie des aliments — Méthode horizontale pour le dénombrement des micro-organismes psychrotrophes,2001-05-17,1,['07.100.30'],ISO/TC 34/SC 9,9599,,[67437],"['en','fr']",7,

59668,IS,,ISO 17411:2014,Optics and photonics — Optical materials and components — Test method for homogeneity of optical glasses by laser interferometry,Optique et photonique — Matériaux et composants optiques — Méthode d'essai d'homogénéité des verres optiques par interférométrie laser,2014-05-19,1,['37.020'],ISO/TC 172/SC 3,9599,,[80013],"['en','fr']",16,<p>ISO 17411:2014 specifies the measuring method for the homogeneity of the refractive index of optical glasses by laser interferometry.</p>

70077,IS,,ISO 17419:2018,Intelligent transport systems — Cooperative systems — Globally unique identification,Systèmes intelligents de transport — Systèmes coopératifs — Identification unique au niveau global,2018-05-11,1,"['35.240.60','03.220.20']",ISO/TC 204,9599,[59720],[88231],"['en','fr']",46,"<p>This document</p><p>— describes and specifies globally unique addresses and identifiers (ITS-S object identifiers) which are both internal and external to ITS stations and are used for ITS station management,</p><p>— describes how ITS-S object identifiers and related technical parameters are used for classification, registration and management of ITS applications and ITS appli

85905,IS,Amd,ISO 17419:2018/Amd 1:2024,Intelligent transport systems — Cooperative systems — Globally unique identification — Amendment 1: Regions of a closed polygon in a plane,Systèmes intelligents de transport — Systèmes coopératifs — Identification unique au niveau global — Amendement 1: Régions d'un polygone fermé dans un plan,2024-01-19,1,"['35.240.60','03.220.20']",ISO/TC 204,9599,,[88231],"['en','fr']",4,

33053,IS,,ISO 17422:2002,Plastics — Environmental aspects — General guidelines for their inclusion in standards,Matières plastiques — Aspects liés à l'environnement — Lignes directrices générales pour leur prise en compte dans les normes,2002-10-10,1,"['83.080.01','13.020.01']",ISO/TC 61/SC 14,9599,,"[70028,52132]",['en'],12,"<p>ISO 17422:2002 provides a structure for inclusion of environmental aspects in standards for plastics products. It proposes an approach which is directed at minimizing any adverse environmental impact without detracting from the primary purpose of ensuring adequate fitness for use of the products under consideration.</p><p>The guidance provided by this International S

68267,IS,,ISO 17423:2018,Intelligent transport systems — Cooperative systems — Application requirements and objectives,Systèmes de transport intelligents — Systèmes Coopératifs — Exigences et objectifs de l'application,2018-05-03,1,"['35.240.60','03.220.20']",ISO/TC 204,9599,[59721],[88232],"['en','fr']",34,"<p>This document</p><p>— specifies communication service parameters presented by ITS station (ITS-S) application processes to the ITS-S management in support of automatic selection of ITS-S communication profiles in an ITS station unit (ITS-SU),</p><p>— specifies related procedures for the static and dynamic ITS-S communication profile selection processes at a high fun

28460,IS,,ISO 17433:2001,Space data and information transfer systems — Packet telemetry services,Systèmes de transfert des informations et données spatiales — Services de télémesure par paquets,2001-06-14,1,['49.140'],ISO/TC 20/SC 13,9599,,[36448],"['en','fr']",87,

59771,IS,,ISO 17442:2012,Financial services — Legal Entity Identifier (LEI),Services financiers — Schéma d'identifiant d'entité légale (IEL),2012-05-29,1,['03.060'],ISO/TC 68/SC 8,9599,,[75998],['en'],6,<p>ISO 17442:2012 specifies the elements of an unambiguous legal entity identifier (LEI) scheme to identify the legal entities relevant to any financial transaction.</p>

75998,IS,,ISO 17442:2019,Financial services — Legal entity identifier (LEI),Services financiers — Schéma d'identifiant d'entité légale (IEL),2019-04-12,2,['03.060'],ISO/TC 68/SC 8,9599,[59771],"[79917,78829]",['en'],6,"<p>This document specifies the minimum elements of an unambiguous legal entity identifier (LEI) scheme to identify the legal entities relevant to any financial transaction.</p><p>It is applicable to legal entities, which include, but are not limited to, unique parties that are legally or financially responsible for the performance of financial transactions or have the legal right in their jurisdiction to enter independently into legal contracts, regardless of whether they are

59789,IS,,ISO 17447-1:2015,Road Vehicles — Glow-plugs with conical seating and their cylinder head housing — Part 1: Basic characteristics and dimensions for metal-sheath-type glow-plugs,Véhicules routiers — Bougies de préchauffage à fourreau et à siège conique et leur logement dans la culasse — Partie 1: Caractéristiques de base et dimensions des bougies de préchauffage à fourreau de type métallique,2015-05-13,1,['43.060.50'],ISO/TC 22/SC 32,9599,"[50144,20089,59787,20090,43934,42942]",[76115],['en'],13,"<p>ISO 17447-1:2015 specifies the main properties and dimensions of metal-sheath-type glow-plugs, including the terminals and the dimensions of their cylinder head housings, for use with di

6366,IS,,ISO 1746:1983,Rubber or plastics hoses and tubing — Bending tests,Tuyaux et tubes en caoutchouc ou en plastique — Essais de courbure,1983-11-01,2,['23.040.70'],ISO/TC 45/SC 1,9599,,[25523],"['en','fr']",4,

25523,IS,,ISO 1746:1998,Rubber or plastics hoses and tubing — Bending tests,Tuyaux et tubes en caoutchouc ou en plastique — Essais de courbure,1998-05-07,3,"['23.040.20','23.040.70']",ISO/TC 45/SC 1,9599,[6366],"[37252,45965]","['en','fr']",6,

32118,IS,Cor,ISO 1746:1998/Cor 1:1999,Rubber or plastics hoses and tubing — Bending tests — Technical Corrigendum 1,Tuyaux et tubes en caoutchouc ou en plastique — Essais de courbure — Rectificatif technique 1,1999-05-06,3,"['23.040.20','23.040.70']",ISO/TC 45/SC 1,9599,,"[37252,45965]",['en'],1,

59838,IS,,ISO 17463:2014,Paints and varnishes — Guidelines for the determination of anticorrosive properties of organic coatings by accelerated cyclic electrochemical technique,Peintures et vernis — Lignes directrices pour la détermination des propriétés anticorrosives de revêtements organiques par une technique électrochimique cyclique accélérée,2014-07-21,1,['87.040'],ISO/TC 35/SC 9,9599,,[81404],"['en','fr','ru']",14,"<p>ISO 17463:2014 gives guidelines on how to perform accelerated cyclic electrochemical technique (ACET) with organic protective coatings on metals.</p><p>ISO 17463:2014 specifies:</p><p>- the instrumental assembly;</p><p>- the execution of an ACET test and the con

59858,IS,,ISO 17468:2016,Microbiology of the food chain — Technical requirements and guidance on establishment or revision of a standardized reference method,Microbiologie de la chaîne alimentaire — Exigences et recommandations techniques pour le développement ou la révision d'une méthode de référence normalisée,2016-06-17,1,['07.100.30'],ISO/TC 34/SC 9,9599,,[79101],"['en','fr']",5,"<p>ISO 17468:2016 gives technical requirements and guidance on the establishment or revision of standardized reference methods for the analysis (detection or quantification) of microorganisms in</p><p>- products intended for human consumption and for the feeding of animals,</p><p>- environmental sample

6368,IS,,ISO 1747:1976,"Rubber, vulcanized — Determination of adhesion to rigid plates in shear — Quadruple shear method","Caoutchouc vulcanisé — Détermination de l'adhérence, en cisaillement, à des plaques rigides — Méthode du quadruple cisaillement",1976-04-01,3,['83.060'],ISO/TC 45/SC 2,9599,[6367],[6477],"['en','fr']",4,

30680,IS,,ISO 17470:2004,Microbeam analysis — Electron probe microanalysis — Guidelines for qualitative point analysis by wavelength dispersive X-ray spectrometry,Analyse par microfaisceaux — Analyse par microsonde électronique (Microsonde de Castaing) — Lignes directrices pour l'analyse qualitative ponctuelle par spectrométrie de rayons X à dispersion de longueur d'onde (WDX),2004-09-13,1,['71.040.99'],ISO/TC 202/SC 2,9599,,[64783],"['en','fr']",10,"<p>ISO 17470:2004 gives guidance for the identification of elements and the investigation of the presence of specific elements, within a specific volume, contained in a specimen, by analysing X-ray spectra obtained using wavelength dispersive X-

33091,IS,,ISO 17484-1:2006,Plastics piping systems — Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) — Part 1: Specifications for systems,Systèmes de canalisations en matières plastiques — Tubes multicouches et leurs assemblages pour une pression maximale de service inférieure ou égale à 5 bar (500 kPa) destinés à l'alimentation en gaz à l'intérieur des bâtiments — Partie 1: Spécifications pour les systèmes,2006-09-22,1,"['23.040.45','23.040.20','91.140.40']",ISO/TC 138/SC 4,9599,,[57597],['en'],33,"<p>ISO 17484-1:2006 specifies the general requirements and the performance requirements for multilayer pipe systems base

51146,IS,Cor,ISO 17484-1:2006/Cor 1:2008,Plastics piping systems — Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) — Part 1: Specifications for systems — Technical Corrigendum 1,Systèmes de canalisations en matières plastiques — Tubes multicouches et leurs assemblages pour une pression maximale de service inférieure ou égale à 5 bar (500 kPa) destinés à l'alimentation en gaz à l'intérieur des bâtiments — Partie 1: Spécifications pour les systèmes — Rectificatif technique 1,2008-02-18,1,"['23.040.45','23.040.20','91.140.40']",ISO/TC 138/SC 4,9599,,[57597],['en'],2,

6369,IS,,ISO 1749:1973,Aircraft — Elastomeric sealing rings — Packaging and identification,Aéronautique — Joints d'étanchéité en élastomère — Emballage et identification,1973-06-01,1,"['83.140.50','49.080']",ISO/TC 20/SC 10,9599,,[68316],"['en','fr']",1,"<p>Specifies the requirements. It is essential that these rings be individually enclosed in sealed envelopes or in pockets in a multiple envelope provided that they can be removed without affecting the sealing of the remainder of the components in the package. The marking of package shall include the part number, material specification number, quarter and year of cure, compound number, acceptance batch number and manufacturer's identity.</p>

30697,IS,,ISO 17491:2002,Protective clothing — Protection against gaseous and liquid chemicals — Determination of resistance of protective clothing to penetration by liquids and gases,Vêtements de protection — Protection contre les produits chimiques liquides et gazeux — Détermination de la résistance des vêtements de protection à la pénétration des liquides et des gaz,2002-05-02,1,['13.340.10'],ISO/TC 94/SC 13,9599,,"[55327,43517,43518,43519,43516]","['en','fr']",26,

43519,IS,,ISO 17491-4:2008,Protective clothing — Test methods for clothing providing protection against chemicals — Part 4: Determination of resistance to penetration by a spray of liquid (spray test),Vêtements de protection — Méthodes d'essai pour les vêtements fournissant une protection contre les produits chimiques — Partie 4: Détermination de la résistance à la pénétration par vaporisation de liquide (essai au brouillard),2008-08-11,1,['13.340.10'],ISO/TC 94/SC 13,9599,[30697],[69029],"['en','fr']",8,"<p>ISO 17491-4:2008 specifies methods for determining the resistance of chemical protective clothing to penetration by sprays of liquid chemicals at two different levels of intensity:</p><u

63670,IS,Amd,ISO 17491-4:2008/Amd 1:2016,Protective clothing — Test methods for clothing providing protection against chemicals — Part 4: Determination of resistance to penetration by a spray of liquid (spray test) — Amendment 1,Vêtements de protection — Méthodes d'essai pour les vêtements fournissant une protection contre les produits chimiques — Partie 4: Détermination de la résistance à la pénétration par vaporisation de liquide (essai au brouillard) — Amendement 1,2016-02-10,1,['13.340.10'],ISO/TC 94/SC 13,9599,,[69029],"['en','fr']",2,

55327,IS,,ISO 17491-5:2013,Protective clothing — Test methods for clothing providing protection against chemicals — Part 5: Determination of resistance to penetration by a spray of liquid (manikin spray test),Vêtements de protection - Méthodes d'essai pour les vêtements fournissant une protection contre les produits chimiques — Partie 5: Détermination de la résistance à la pénétration par vaporisation de liquide (essai au brouillard à l'aide d'un mannequin),2013-11-08,1,['13.340.10'],ISO/TC 94/SC 13,9599,[30697],[83202],['en'],7,<p>ISO 17491-5:2013 specifies an alternative test method to the one described in ISO 17491-4.</p><p>The method for determining the resistance to chemical spray penet

30698,IS,,ISO 17492:2003,Clothing for protection against heat and flame — Determination of heat transmission on exposure to both flame and radiant heat,Vêtements de protection contre la chaleur et la flamme — Détermination de la transmission de chaleur lors de l'exposition simultanée à une flamme et à une source de chaleur radiante,2003-05-13,1,['13.340.10'],ISO/TC 94/SC 13,9599,,[61512],"['en','fr']",19,"<p>ISO 17492:2003 specifies a test method for measuring the heat transfer of horizontally mounted flame-resistant textile materials when exposed to a combination of convective and radiant energy.</p><p>This test method can be used for any type of sheet material used either as a single layer

40327,IS,Cor,ISO 17492:2003/Cor 1:2004,Clothing for protection against heat and flame — Determination of heat transmission on exposure to both flame and radiant heat — Technical Corrigendum 1,Vêtements de protection contre la chaleur et la flamme — Détermination de la transmission de chaleur lors de l'exposition simultanée à une flamme et à une source de chaleur radiante — Rectificatif technique 1,2004-03-30,1,['13.340.10'],ISO/TC 94/SC 13,9599,,[61512],"['en','fr']",1,

30699,IS,,ISO 17493:2000,Clothing and equipment for protection against heat — Test method for convective heat resistance using a hot air circulating oven,Vêtements et équipement de protection contre la chaleur — Méthode d'essai de la résistance à la chaleur de convection au moyen d'un four à circulation d'air chaud,2000-12-21,1,['13.340.10'],ISO/TC 94/SC 13,9599,,[61513],"['en','fr']",6,

31399,IS,,ISO 17499:2006,Carbonaceous materials used in the production of aluminium — Determination of baking level expressed by equivalent temperature,Produits carbonés utilisés pour la production de l'aluminium — Détermination du niveau de cuisson par estimation de la température de cuisson équivalente,2006-01-30,1,['71.100.10'],ISO/TC 226,9599,,[82871],['en'],5,"<p>ISO 17499:2006 covers carbonaceous materials used in the production of aluminium.</p><p>ISO 17499:2006 specifies the determination of the equivalent temperature of one anode or cathode in a baking furnace, and the calculation of the overall baking level in a section in the baking furnace.</p>"

4010,IS,,ISO 175:1981,"Plastics — Determination of the effects of liquid chemicals, including water","Plastiques — Détermination de l'action des agents chimiques liquides, y compris l'eau",1981-07-01,1,['83.080.01'],ISO/TC 61/SC 6,9599,[4489],[28170],"['en','fr']",12,

28170,IS,,ISO 175:1999,Plastics — Methods of test for the determination of the effects of immersion in liquid chemicals,Plastiques — Méthodes d'essai pour la détermination des effets de l'immersion dans des produits chimiques liquides,1999-05-06,2,['83.080.01'],ISO/TC 61/SC 6,9599,[4010],[55483],"['en','fr']",19,

6370,IS,,ISO 1750:1981,Pesticides and other agrochemicals — Common names,Produits phytosanitaires et assimilés — Noms communs,1981-12-01,1,['65.100.01'],ISO/TC 81,9599,"[5401,4749,5554,5402,5403,5404,4214,4657,5405,4091,3918,4418,4159,5074]","[65073,46548,67887,84519]","['en','fr']",87,<p>Covers pest control chemicals and plant growth regulators of international importance. The standard is presented as a combined English/French text. It gives references to related standards and specifies the principles for the selection of names and the style of writing.</p>

6371,IS,Add,ISO 1750:1981/Add 1:1983,Pesticides and other agrochemicals — Common names — Addendum 1,Produits phytosanitaires et assimilés — Noms communs — Additif 1,1983-08-01,1,['65.100.01'],ISO/TC 81,9599,,"[65073,46548,67887,84519]","['en','fr']",7,

6372,IS,Add,ISO 1750:1981/Add 2:1983,Pesticides and other agrochemicals — Common names — Addendum 2,Produits phytosanitaires et assimilés — Noms communs — Additif 2,1983-12-01,1,['65.100.01'],ISO/TC 81,9599,,"[65073,46548,67887,84519]","['en','fr']",32,

6379,IS,Amd,ISO 1750:1981/Amd 1:1982,Pesticides and other agrochemicals — Common names — Amendment 1,Produits phytosanitaires et assimilés — Noms communs — Amendement 1,1982-12-01,1,['65.100.01'],ISO/TC 81,9599,,"[65073,46548,67887,84519]","['en','fr']",2,"<p>Correct the (E) chemical names on: page 20, chlorprocarb; page 31, dimethrin; page 41, fenitrothion; page 63, parafluron; according to the names given in the amendment. Page 72, simetryn: correct the (F) spelling as given in the amendment. Page 47, HHDN, and page 80, tridemorph: replace the structure, and correct the chemical names for 'tridemorph', as given in the amendment.</p>"

30915,IS,Amd,ISO 1750:1981/Amd 2:1999,Pesticides and other agrochemicals — Common names — Amendment 2,Produits phytosanitaires et assimilés — Noms communs — Amendement 2,1999-11-11,1,['65.100.01'],ISO/TC 81,9599,,"[65073,46548,67887,84519]","['en','fr']",38,

34647,IS,Amd,ISO 1750:1981/Amd 3:2001,Pesticides and other agrochemicals — Common names — Amendment 3,Produits phytosanitaires et assimilés — Noms communs — Amendement 3,2001-12-06,1,['65.100.01'],ISO/TC 81,9599,,"[65073,46548,67887,84519]","['en','fr']",25,

44608,IS,Amd,ISO 1750:1981/Amd 4:2008,Pesticides and other agrochemicals — Common names — Amendment 4,Produits phytosanitaires et assimilés — Noms communs — Amendement 4,2008-04-24,1,['65.100.01'],ISO/TC 81,9599,,"[65073,46548,67887,84519]","['en','fr']",12,

44984,IS,Amd,ISO 1750:1981/Amd 5:2008,Pesticides and other agrochemicals — Common names — Amendment 5,Produits phytosanitaires et assimilés — Noms communs — Amendement 5,2008-10-22,1,['65.100.01'],ISO/TC 81,9599,,"[65073,46548,67887,84519]","['en','fr']",102,

66863,IS,Amd,ISO 1750:1981/Amd 6:2018,Pesticides and other agrochemicals — Common names — Amendment 6: Meptyldinocap,Produits phytosanitaires et assimilés — Noms communs — Amendement 6: Méptyldinocap,2018-02-01,1,['65.100.01'],ISO/TC 81,9599,,[84519],"['en','fr']",1,

80962,IS,Amd,ISO 1750:1981/Amd 7:2021,Pesticides and other agrochemicals — Common names — Amendment 7,Produits phytosanitaires et assimilés — Noms communs — Amendement 7,2021-12-03,1,['65.100.01'],ISO/TC 81,9599,,[84519],['en'],102,

6380,IS,,ISO 1751:1977,Shipbuilding — Ships' side scuttles,Construction navale — Hublots de navires,1977-06-01,1,['47.020.10'],ISO/TC 8/SC 8,9599,,[6381],"['en','fr']",11,

6381,IS,,ISO 1751:1993,Shipbuilding and marine structures — Ships'side scuttles,Construction navale et structures maritimes — Hublots de navires,1993-02-18,2,['47.020.10'],ISO/TC 8/SC 8,9599,[6380],[54515],"['en','fr']",15,"<p>Specifies the classification (series, types and models) and gives the dimensions for interchangeability and construction, materials, tests, marking and designation of the side scuttles.</p>"

30713,IS,,ISO 17510-1:2002,Sleep apnoea breathing therapy — Part 1: Sleep apnoea breathing therapy devices,Thérapie respiratoire de l'apnée du sommeil — Partie 1: Dispositifs de thérapie respiratoire de l'apnée du sommeil,2002-02-14,1,['11.040.10'],ISO/TC 121/SC 3,9599,,[41615],"['en','fr']",26,"<p>For ISO 17510-1:2002, the scope given in clause 1 of EN 60601-1:1990 + A1:1993 and A12:1993 applies with the following addition.</p><p>ISO 17510-1:2002 specifies requirements for devices intended for sleep apnoea breathing therapy for domiciliary use and for use in healthcare institutions.</p><p>ISO 17510-1:2002 is not applicable to jet and very high frequency ventilation and oscillation.</p><p>IS

40129,IS,Cor,ISO 17510-1:2002/Cor 1:2004,Sleep apnoea breathing therapy — Part 1: Sleep apnoea breathing therapy devices — Technical Corrigendum 1,Thérapie respiratoire de l'apnée du sommeil — Partie 1: Dispositifs de thérapie respiratoire de l'apnée du sommeil — Rectificatif technique 1,2004-02-12,1,['11.040.10'],ISO/TC 121/SC 3,9599,,[41615],['fr'],,

41615,IS,,ISO 17510-1:2007,Sleep apnoea breathing therapy — Part 1: Sleep apnoea breathing therapy equipment,Thérapie respiratoire de l'apnée du sommeil — Partie 1: Équipement de thérapie respiratoire de l'apnée du sommeil,2007-09-25,2,['11.040.10'],ISO/TC 121/SC 3,9599,"[30713,40129]",[60049],"['en','fr','ru']",34,"<p>ISO 17510-1:2007 specifies requirements for equipment intended for sleep apnoea breathing therapy for domiciliary use, ships, aircraft and other transport vehicles and for use in healthcare institutions.</p><p>ISO 17510-1:2007 applies to equipment intended for use with adults and children, and excludes equipment intended for use with neonates.</p><p>Jet and very high frequency

33782,IS,,ISO 17510-2:2003,Sleep apnoea breathing therapy — Part 2: Masks and application accessories,Thérapie de l'apnée du sommeil — Partie 2: Masques et accessoires thérapeutiques,2003-01-06,1,['11.040.10'],ISO/TC 121/SC 3,9599,,[41616],['en'],9,"<p>ISO 17510-2:2002 specifies requirements for masks and accessories which are required to connect the patient connection port to a sleep apnoea breathing therapy device and the mask to a patient, and are used for the application of sleep apnoea breathing therapy, e.g. nasal masks, gas exhaust ports, connecting elements and headgear.</p><p>ISO 17510-2:2002 does not cover oral appliances.</p><p>NOTE 1 Sleep apnoea breathing therapy devices are cov

41616,IS,,ISO 17510-2:2007,Sleep apnoea breathing therapy — Part 2: Masks and application accessories,Thérapie respiratoire de l'apnée du sommeil — Partie 2: Masques et accessoires d'application,2007-09-25,2,['11.040.10'],ISO/TC 121/SC 3,9599,[33782],"[64910,59223]","['en','fr','ru']",29,"<p>ISO 17510-2:2007 applies to masks, their fixing and to the accessories used to connect a sleep apnoea breathing therapy equipment to the patient. It specifies requirements for masks and accessories, including any connecting element, that are required to connect the patient connection port of sleep apnoea breathing therapy equipment to a patient, and are used for the application of sleep apnoea breathing

64910,IS,,ISO 17510:2015,Medical devices — Sleep apnoea breathing therapy — Masks and application accessories,Dispositifs médicaux — Thérapie respiratoire de l'apnée du sommeil — Masques et accessoires d'application,2015-07-23,1,['11.040.10'],ISO/TC 121/SC 3,9599,[41616],[89025],"['en','fr']",30,"<p>ISO 17510:2015 applies to masks and their accessories used to connect a sleep apnoea breathing therapy equipment to the patient. It specifies requirements for masks and accessories, including any connecting element, that are required to connect the patient-connection port of sleep apnoea breathing therapy equipment to a patient for the application of sleep apnoea breathing therapy (e.g. nasal mas

30716,IS,,ISO 17511:2003,In vitro diagnostic medical devices — Measurement of quantities in biological samples — Metrological traceability of values assigned to calibrators and control materials,Dispositifs médicaux de diagnostic in vitro — Mesurage des grandeurs dans des échantillons d'origine biologique — Traçabilité métrologique des valeurs attribuées aux agents d'étalonnage et aux matériaux de contrôle,2003-08-22,1,['11.100.10'],ISO/TC 212,9599,,[69984],['en'],23,"<p>ISO 17511:2003 specifies how to assure the metrological traceability of values assigned to calibrators and control materials intended to establish or verify trueness of measurement. The calibrators and control materials are

31404,IS,,ISO 17514:2004,Time-measuring instruments — Photoluminescent deposits — Test methods and requirements,Instruments de mesure du temps — Dépôts photoluminescents — Méthodes d'essai et exigences,2004-12-02,1,['39.040.01'],ISO/TC 114/SC 5,9599,,[78645],"['en','fr']",5,"<p>ISO 17514:2004 specifies the test methods for the photoluminescent deposits applied to time-measuring instruments, together with the requirements related to them.</p>"

59946,IS,,ISO 17520:2016,Space environment (natural and artificial) — Cosmic ray and solar energetic particle penetration inward the magnetosphere — Method of determination of the effective vertical cut-off rigidity,Systèmes spatiaux (naturel et artificiel) — Rayons cosmiques et pénétration de particule énergétique solaire dans la magnétosphère — Méthode de détermination de la rigidité de coupure verticale effective,2016-04-20,1,['49.140'],ISO/TC 20/SC 14,9599,,[82392],['en'],11,"<p>ISO 17520:2016 describes the effective vertical cut-off rigidities of charged particles for near-Earth space and establishes principal requirements for their calculation. In Annex A, the calculation technique is

59952,IS,,ISO 17523:2016,Health informatics — Requirements for electronic prescriptions,Informatique de santé — Exigences applicables aux prescriptions électroniques,2016-06-01,1,['35.240.80'],ISO/TC 215,9599,,"[84221,86438]","['en','fr']",18,"<p>ISO 17523:2016 specifies the requirements that apply to electronic prescriptions. It describes generic principles that are considered important for all electronic prescriptions.</p><p>ISO 17523:2016 is constrained to the content of the electronic prescription itself, the digital document which is issued by a prescribing healthcare professional and received by a dispensing healthcare professional. The prescribed medicinal product is to be dispensed t

6382,IS,,ISO 1753:1975,Cinematography — Recording and reproducing head gaps for six-track magnetic sound records on 35 mm motion-picture film containing no picture — Positions and width dimensions,Cinématographie — Entrefers des têtes magnétiques pour l'enregistrement et la lecture sonores à six pistes sur film cinématographique 35 mm sans image — Emplacement et dimensions,1975-01-01,1,['37.060.20'],ISO/TC 36,9599,,[3996],"['en','fr']",2,

6383,IS,,ISO 1754:1974,Photography — Cameras using films 35 mm and smaller — Picture sizes,Photographie — Appareils photographiques utilisant les films de 35 mm et moins — Dimensions des images,1974-07-01,2,['37.040.10'],ISO/TC 42,9599,,[6384],['en'],1,

6384,IS,,ISO 1754:1986,Photography — Cameras using 35 mm and 16 mm film — Picture sizes,Photographie — Appareils photographiques utilisant des films 35 mm et 16 mm — Dimensions des images,1986-08-28,3,['37.040.10'],ISO/TC 42,9599,[6383],[20052],"['en','fr']",1,

20052,IS,,ISO 1754:1998,Photography — Cameras using 35 mm film and roll film — Picture sizes,Photographie — Appareils photographiques utilisant des films et pellicules de 35 mm — Dimensions d'image,1998-10-15,4,['37.040.10'],ISO/TC 42,9599,[6384],[55864],['en'],2,

36428,IS,Cor,ISO 1754:1998/Cor 1:2002,Photography — Cameras using 35 mm film and roll film — Picture sizes — Technical Corrigendum 1,Photographie — Appareils photographiques utilisant des films et pellicules de 35 mm — Dimensions d'image — Rectificatif technique 1,2002-02-28,4,['37.040.10'],ISO/TC 42,9599,,[55864],['en'],2,

59993,IS,,ISO 17540:2016,Space systems — Liquid rocket engines and test stands — Terms and definitions,Systèmes spatiaux — Moteurs de fusée liquides et stands d'essai — Termes et définitions,2016-11-25,1,['49.140'],ISO/TC 20/SC 14,9599,,[85524],['en'],32,"<p>ISO 17540:2016 provides terms and definitions in scope of design, testing, reliability analysis and quality control of liquid rocket engines. The terms are required for use in all types of documentation and literature including in the scope of standardization or using the results of this activity.</p>"

33116,IS,,ISO 17544:2004,Carbonaceous materials used in the production of aluminium — Cold and tepid ramming pastes — Determination of rammability of unbaked pastes,Produits carbonés utilisés pour la production de l'aluminium — Pâtes de brasquage froides et tièdes — Détermination de l'aptitude au brasquage des pâtes non cuites,2004-07-16,1,['71.100.10'],ISO/TC 226,9599,,[86641],['en'],6,<p>ISO 17544:2004 describes a method of producing a compaction curve indicating the rammability of carbonaceous ramming pastes used to line cathodes utilized in the production of aluminium.</p>

60028,IS,,ISO 17546:2016,Space systems — Lithium ion battery for space vehicles — Design and verification requirements,Systèmes spatiaux — Batteries à ions lithium pour véhicules spatiaux — Exigences de vérification et de conception,2016-03-09,1,['49.140'],ISO/TC 20/SC 14,9599,,[83872],['en'],52,"<p>ISO 17546:2016 specifies design and minimum verification requirements for lithium ion rechargeable (including lithium ion polymer) batteries for space vehicles.</p><p>Lithium ion secondary electrochemical systems use intercalation compounds (intercalated lithium exists in an ionic or quasi-atomic form within the lattice of the electrode material) in the positive and in the negative electrodes.</

6385,IS,,ISO 1755:1973,Photography — Projector slides — Dimensions,"Photographie — Diapositives montées, pour projection — Dimensions",1973-10-01,1,['37.040.10'],ISO/TC 42,9599,,[6386],"['en','fr']",2,

34953,IS,,ISO 17554:2005,Reaction to fire tests — Mass loss measurement,Essais de réaction au feu — Mesurage de la perte de masse,2005-07-11,1,"['13.220.40','13.220.50']",ISO/TC 92/SC 1,9599,,[55678],['en'],18,<p>ISO 17554:2005 specifies a small-scale method for assessing the mass loss rate of essentially flat specimens exposed in the horizontal orientation to controlled levels of radiant heating with an external igniter under well-ventilated conditions. The mass loss rate is determined by measurement of the specimen mass and is derived numerically. The time to ignition (sustained flaming) is also measured in this test. Mass loss rate can be used as an indirect measure of heat release rate f

30583,IS,,ISO 17555:2003,Plastics — Film and sheeting — Biaxially oriented polypropylene (PP) films,Plastiques — Film et feuille — Films en polypropylène (PP) bi-orientés,2003-09-10,1,['83.140.10'],ISO/TC 61/SC 11,9599,,[80200],['en'],6,"<p>ISO 17555:2003 specifies the requirements for biaxially oriented polypropylene (PP) films, which are mainly used for packaging. The film may be used alone or in laminates with other films.</p><p>This International Standard applies only to films composed of more than 95 % (by mass) of polypropylene.</p>"

30743,IS,,ISO 17556:2003,Plastics — Determination of the ultimate aerobic biodegradability in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved,Plastiques — Détermination de la biodégradabilité aérobie ultime dans le sol par mesure de la demande en oxygène dans un respiromètre ou de la teneur en dioxyde de carbone libéré,2003-07-18,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[56089],"['en','fr']",16,"<p>ISO 17556:2003 specifies a method for determining the ultimate aerobic biodegradability of plastic materials in soil by measuring the oxygen demand in a closed respirometer or the amount of carbon dioxide evolved. The method is designed to yield an optimum

56089,IS,,ISO 17556:2012,Plastics — Determination of the ultimate aerobic biodegradability of plastic materials in soil by measuring the oxygen demand in a respirometer or the amount of carbon dioxide evolved,Plastiques — Détermination de la biodégradabilité aérobie ultime des matériaux plastiques dans le sol par mesure de la demande en oxygène dans un respiromètre ou de la teneur en dioxyde de carbone libéré,2012-08-08,2,['83.080.01'],ISO/TC 61/SC 14,9599,[30743],[74993],"['en','fr']",26,"<p>ISO 17556:2012 specifies a method for determining the ultimate aerobic biodegradability of plastic materials in soil by measuring the oxygen demand in a closed respirometer or the amount of carbon dioxi

30747,IS,,ISO 17560:2002,Surface chemical analysis — Secondary-ion mass spectrometry — Method for depth profiling of boron in silicon,Analyse chimique des surfaces — Spectrométrie de masse des ions secondaires — Dosage du bore dans le silicium par profilage d'épaisseur,2002-07-18,1,['71.040.40'],ISO/TC 201/SC 6,9599,,[65114],"['en','fr']",10,"<p>ISO 17560:2002 specifies a secondary-ion mass spectrometric method using magnetic-sector or quadrupole mass spectrometers for depth profiling of boron in silicon, and using stylus profilometry or optical interferometry for depth scale calibration. This method is applicable to single-crystal, poly-crystal or amorphous-silicon specimens with boron atom

30748,IS,,ISO 17561:2002,"Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for elastic moduli of monolithic ceramics at room temperature by sonic resonance","Céramiques techniques — Méthode d'essai des modules d'élasticité des céramiques monolithiques, à température ambiante, par résonance acoustique",2002-03-14,1,['81.060.30'],ISO/TC 206,9599,,[65413],['en'],10,"<p>ISO 17561 describes the method of test for determining the dynamic elastic moduli of fine ceramics at room temperature by sonic resonance. This International Standard is for fine ceramics that are elastic, homogeneous and isotropic.</p>"

50400,IS,Cor,ISO 17561:2002/Cor 1:2007,"Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for elastic moduli of monolithic ceramics at room temperature by sonic resonance — Technical Corrigendum 1","Céramiques techniques — Méthode d'essai des modules d'élasticité des céramiques monolithiques, à température ambiante, par résonance acoustique — Rectificatif technique 1",2007-10-16,1,['81.060.30'],ISO/TC 206,9599,,[65413],['en'],1,

30749,IS,,ISO 17562:2001,"Fine ceramics (advanced ceramics, advanced technical ceramics) - Test method for linear thermal expansion of monolithic ceramics by push-rod technique",Céramiques techniques — Méthode d'essai pour le coefficient d'expansion thermique linéaire des céramiques monolithiques par la technique du poussoir de soupape,2001-10-25,1,['81.060.30'],ISO/TC 206,9599,,"[63274,63895]","['en','fr']",10,

30751,IS,,ISO 17564:2001,Nitrile rubber — Determination of residual unsaturation in hydrogenated nitrile rubber (HNBR) by iodine value,Caoutchouc nitrile — Détermination de l'insaturation résiduelle dans le caoutchouc nitrile hydrogéné (HNBR) par l'indice d'iode,2001-02-15,1,['83.060'],ISO/TC 45/SC 2,9599,,[45394],['en'],6,

30754,IS,,ISO 17567:2005,Agricultural and forestry tractors and implements — Hydraulic power beyond,Tracteurs agricoles et forestiers et instruments — Puissance hydraulique externe disponible,2005-05-13,1,['65.060.10'],ISO/TC 23/SC 4,9599,,"[69762,74976]",['en'],9,"<p>ISO 17567:2005 specifies the hydraulic power beyond of tractors used in agricultural and forestry, and the number, type, capacity and identification of the associated connections between these tractors and their implements.</p>"

6388,IS,,ISO 1757:1980,Personal photographic dosemeters,Dosimètres photographiques personnels,1980-06-01,1,['13.280'],ISO/TC 85,9599,,[20485],"['en','fr']",9,

45960,IS,,ISO 17572-1:2008,Intelligent transport systems (ITS) — Location referencing for geographic databases — Part 1: General requirements and conceptual model,Systèmes intelligents de transport (SIT) — Localisation pour bases de données géographiques — Partie 1: Exigences générales et modèle conceptuel,2008-12-08,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,,[63400],"['en','fr']",41,"<p>ISO 17572 specifies Location Referencing Methods (LRM) that describe locations in the context of geographic databases and will be used to locate transport-related phenomena in an encoder system as well as in the decoder side. It defines what is meant by such objects, and describes the reference in detail

63400,IS,,ISO 17572-1:2015,Intelligent transport systems (ITS) — Location referencing for geographic databases — Part 1: General requirements and conceptual model,Systèmes intelligents de transport (SIT) — Localisation pour bases de données géographiques — Partie 1: Exigences générales et modèle conceptuel,2015-01-05,2,"['35.240.60','03.220.01']",ISO/TC 204,9599,[45960],[81955],['en'],29,"<p>The ISO 17572 series specifies location referencing methods (LRMs) that describe locations in the context of geographic databases and will be used to locate transport-related phenomena in an encoder system as well as in the decoder side. The ISO 17572 series defines what is meant by such objects and desc

45961,IS,,ISO 17572-2:2008,Intelligent transport systems (ITS) — Location referencing for geographic databases — Part 2: Pre-coded location references (pre-coded profile),Systèmes intelligents de transport (SIT) — Localisation pour bases de données géographiques — Partie 2: Localisations précodées (profil précodé),2008-12-08,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,,[63401],"['en','fr']",33,"<p>ISO 17572 specifies Location Referencing Methods (LRM) that describe locations in the context of geographic databases and will be used to locate transport-related phenomena in an encoder system as well as in the decoder side. It defines what is meant by such objects, and describes the reference i

63401,IS,,ISO 17572-2:2015,Intelligent transport systems (ITS) — Location referencing for geographic databases — Part 2: Pre-coded location references (pre-coded profile),Systèmes intelligents de transport (SIT) — Localisation pour bases de données géographiques — Partie 2: Localisations précodées (profil précodé),2015-01-05,2,"['35.240.60','03.220.01']",ISO/TC 204,9599,[45961],[69468],['en'],47,"<p>The ISO 17572 series specifies location referencing methods (LRMs) that describe locations in the context of geographic databases and will be used to locate transport-related phenomena in an encoder system as well as in the decoder side. The ISO 17572 series defines what is meant by such objects

45962,IS,,ISO 17572-3:2008,Intelligent transport systems (ITS) — Location referencing for geographic databases — Part 3: Dynamic location references (dynamic profile),Systèmes intelligents de transport (SIT) — Localisation pour bases de données géographiques — Partie 3: Localisations dynamiques (profil dynamique),2008-12-08,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,,[63402],"['en','fr']",88,"<p>ISO 17572 specifies Location Referencing Methods (LRM) that describe locations in the context of geographic databases and will be used to locate transport-related phenomena in an encoder system as well as in the decoder side. It defines what is meant by such objects, and describes the reference in

54623,IS,Cor,ISO 17572-3:2008/Cor 1:2009,Intelligent transport systems (ITS) — Location referencing for geographic databases — Part 3: Dynamic location references (dynamic profile) — Technical Corrigendum 1,Systèmes intelligents de transport (SIT) — Localisation pour bases de données géographiques — Partie 3: Localisations dynamiques (profil dynamique) — Rectificatif technique 1,2009-07-09,1,"['35.240.60','03.220.01']",ISO/TC 204,9599,,[63402],"['en','fr']",1,

45963,IS,,ISO 17573:2010,Electronic fee collection — Systems architecture for vehicle-related tolling,Perception du télépéage — Architecture de systèmes pour le péage lié aux véhicules,2010-12-13,1,"['35.240.60','03.220.20']",ISO/TC 204,9599,[30757],[71982],['en'],72,"<p>ISO 17573:2010 defines the architecture of a toll system environment in which a customer with one contract can use a vehicle in a variety of toll domains and with a different Toll Charger for each domain.</p><p>Toll systems covered by ISO 17573:2010 can be used for various purposes including road (network) tolling, area tolling, collecting toll for bridges, tunnels, ferries, for access, and for parking. From a technical poin

85042,IS,,ISO 17573-3:2023,Electronic fee collection — System architecture for vehicle-related tolling — Part 3: Data dictionary,Perception de télépéage — Architecture de systèmes pour le péage lié aux véhicules — Partie 3: Dictionnaire de données,2023-08-01,1,"['35.240.60','03.220.20']",ISO/TC 204,9599,[81764],[88214],"['en','fr']",49,"<p class='MsoBodyText'><span lang='EN-GB'>This document specifies the syntax and semantics of data objects in the field of electronic fee collection (EFC). The definitions of data types and assignment of semantics are provided in accordance with the abstract syntax notation one (ASN.1) technique, as specified in ISO/IEC 8824-1. This document defines:</span></

39964,IS,,ISO 17577:2006,Steel — Ultrasonic testing for steel flat products of thickness equal to or greater than 6 mm,Aciers — Contrôle ultrasonore des produits plats en acier d'épaisseur égale ou supérieure à 6 mm,2006-09-06,1,"['77.040.20','77.140.50']",ISO/TC 17/SC 7,9599,,[63157],['en'],12,"<p>ISO 17577:2006 specifies a method for the automated and/or manual ultrasonic testing of uncoated steel flat products for internal discontinuities by the reflection method. It is applicable to non-alloyed or alloyed steel flat products, in a nominal thickness range of 6 mm to 200 mm. However, this standard may be applied to austenitic and austenitic-ferritic steels, provided that the difference bet

6389,IS,,ISO 1758:1976,Direct-reading electroscope-type pocket exposure meters,Exposimètres de poche à lecture directe du type électroscope,1976-12-01,1,['13.280'],ISO/TC 85,9599,,[20486],"['en','fr']",2,

39722,IS,,ISO 17584:2005,Refrigerant properties,Propriétés des fluides frigorigènes,2005-12-12,1,['71.100.45'],ISO/TC 86/SC 8,9599,,[75112],['en'],70,"<p>ISO 17584:2005 specifies thermophysical properties of several commonly used refrigerants and refrigerant blends.</p><p>ISO 17584:2005 is applicable to the refrigerants R12, R22, R32, R123, R125, R134a, R143a, R152a, R717 (ammonia), and R744 (carbon dioxide) and to the refrigerant blends R404A, R407C, R410A, and R507. The following properties are included: density, pressure, internal energy, enthalpy, entropy, heat capacity at constant pressure, heat capacity at constant volume, speed of sound, and the Joule-Thomson coefficient, in both sing

6390,IS,,ISO 1759:1976,Indirect-reading capacitor-type pocket exposure meters and accessory electrometers,Exposimètres de poche à lecture indirecte du type condensateur et électromètres associés,1976-12-01,1,['13.280'],ISO/TC 85,9599,,[20486],"['en','fr']",2,

36872,IS,,ISO 17593:2007,Clinical laboratory testing and in vitro medical devices — Requirements for in vitro monitoring systems for self-testing of oral anticoagulant therapy,Laboratoires d'analyses de biologie médicale et dispositifs médicaux de diagnostic in vitro — Exigences relatives aux systèmes d'autosurveillance des traitements par anti-coagulant oraux,2007-04-17,1,['11.100.20'],ISO/TC 212,9599,,[79378],"['en','ru']",54,"<p>ISO 17593:2007 specifies requirements for <i>in vitro</i> measuring systems for self-monitoring of vitamin-K antagonist therapy, including performance, quality assurance and user training and procedures for the verification and validation of performance by the int

4012,IS,,ISO 176:1976,Plastics — Determination of loss of plasticizers — Activated carbon method,Matières plastiques — Détermination des pertes en plastifiants — Méthode au charbon actif,1976-07-01,1,['83.080.01'],ISO/TC 61/SC 6,9599,,"[33345,38743]","['en','fr']",2,"<p>Specification of two empiric methods for the quantitative determination of the loss in mass of test specimens in presence of activated carbon under given conditions of temperature and time. They are intended for the determination of plasticiser migration from plastics which are exposed to heat. In method A the test piece is in direct contact with activated carbon, while in method B the contact is prevented by a metallic fabri

60106,IS,,ISO 17601:2016,Soil quality — Estimation of abundance of selected microbial gene sequences by quantitative PCR from DNA directly extracted from soil,Qualité du sol — Estimation de l'abondance de séquences de gènes microbiens par amplification par réaction de polymérisation en chaîne (PCR) quantitative à partir d'ADN directement extrait du sol,2016-01-12,1,['13.080.30'],ISO/TC 190/SC 4,9599,,[88096],"['en','fr']",31,"<p>ISO 17601:2016 specifies the crucial steps of a quantitative real-time polymerase chain reaction (qPCR) method to measure the abundance of selected microbial gene sequences from soil DNA extract which provides an estimation of selected microbial groups.</p><p>It is n

33146,IS,,ISO 17604:2003,Microbiology of food and animal feeding stuffs — Carcass sampling for microbiological analysis,Microbiologie des aliments — Prélèvement d'échantillons sur des carcasses en vue de leur analyse microbiologique,2003-09-01,1,['07.100.30'],ISO/TC 34/SC 9,9599,[8245],[62769],"['en','fr']",14,"<p>ISO 17604:2003 specifies sampling methods for the detection and enumeration of microorganisms on the carcass surface of freshly slaughtered (red) meat animals. The microbiological sampling can be carried out as part of the process control (and to verify process control) in slaughter establishments for cattle, horses, pigs, sheep, goats and game raised in captivity, risk-based assur