Withdrawn and superseded ISO standards — page 55 of 246

29049,IS,,ISO 16000-3:2001,Indoor air — Part 3: Determination of formaldehyde and other carbonyl compounds — Active sampling method,Air intérieur — Partie 3: Dosage du formaldéhyde et d'autres composés carbonylés — Méthode par échantillonnage actif,2001-09-06,1,['13.040.20'],ISO/TC 146/SC 6,9599,,[51812],"['en','fr']",26,

51812,IS,,ISO 16000-3:2011,Indoor air — Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air — Active sampling method,Air intérieur — Partie 3: Dosage du formaldéhyde et d'autres composés carbonylés dans l'air intérieur et dans l'air des chambres d'essai — Méthode par échantillonnage actif,2011-10-10,2,['13.040.20'],ISO/TC 146/SC 6,9599,[29049],[81864],"['en','fr']",27,"<p>This part of ISO 16000 specifies a determination of formaldehyde (HCHO) and other carbonyl compounds (aldehydes and ketones) in air. The method is specific to formaldehyde but, with modification, at least 12 other aromatic as well as saturated and unsaturated aliphatic carbo

63690,IS,,ISO 16000-33:2017,Indoor air — Part 33: Determination of phthalates with gas chromatography/mass spectrometry (GC/MS),Air intérieur — Partie 33: Détermination des phthalates par chromatographie en phase gazeuse/spectrométrie de masse (CPG/SM),2017-08-10,1,['13.040.20'],ISO/TC 146/SC 6,9599,,[81881],"['en','fr']",40,"<p>ISO 16000-33:2017 specifies the sampling and analysis of phthalates in indoor air and describes the sampling and analysis of phthalates in house dust and in solvent wipe samples of surfaces by means of gas chromatography/mass spectrometry.</p><p>Two alternative sampling and processing methods, whose comparability has been proven in a round robin test, are specified f

39198,IS,,ISO 16000-4:2004,Indoor air — Part 4: Determination of formaldehyde — Diffusive sampling method,Air intérieur — Partie 4: Dosage du formaldéhyde — Méthode par échantillonnage diffusif,2004-05-11,1,['13.040.20'],ISO/TC 146/SC 6,9599,,[52214],"['en','fr']",9,"<p>ISO 16000-4:2004 specifies a diffusive sampler/solvent desorption/high performance liquid chromatography (HPLC) method for the determination of formaldehyde in indoor air. </p><p>The test method is applicable to the measurement of formaldehyde in indoor air over the range from 0,001 mg/m³ to 1,0 mg/m³ for a sampling period of between 24 h and 72 h. For sampling periods of 24 h, the applicable concentrati

30147,IS,,ISO 16000-6:2004,"Indoor air — Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TA sorbent, thermal desorption and gas chromatography using MS/FID","Air intérieur — Partie 6: Dosage des composés organiques volatils dans l'air intérieur des locaux et enceintes d'essai par échantillonnage actif sur le sorbant Tenax TA, désorption thermique et chromatographie en phase gazeuse utilisant MS/FID",2004-03-12,1,['13.040.20'],ISO/TC 146/SC 6,9599,,[52213],"['en','fr']",25,"<p>ISO 16000-6:2004 specifies a method for determination of volatile organic compounds (VOCs) in indoor air and in air sampled for the determination of the emi

52213,IS,,ISO 16000-6:2011,"Indoor air — Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TA sorbent, thermal desorption and gas chromatography using MS or MS-FID","Air intérieur — Partie 6: Dosage des composés organiques volatils dans l'air intérieur des locaux et chambres d'essai par échantillonnage actif sur le sorbant Tenax TA, désorption thermique et chromatographie en phase gazeuse utilisant MS ou MS-FID",2011-12-01,2,['13.040.20'],ISO/TC 146/SC 6,9599,[30147],[73522],"['en','fr']",29,"<p>ISO 16000-6:2011 specifies a method for determination of volatile organic compounds (VOCs) in indoor air and in air sampled for the determ

38203,IS,,ISO 16000-9:2006,Indoor air — Part 9: Determination of the emission of volatile organic compounds from building products and furnishing — Emission test chamber method,Air intérieur — Partie 9: Dosage de l'émission de composés organiques volatils de produits de construction et d'objets d'équipement — Méthode de la chambre d'essai d'émission,2006-01-30,1,['13.040.20'],ISO/TC 146/SC 6,9599,,[79022],"['en','fr']",15,"<p>ISO 16000-9:2006 specifies a general laboratory test method for determination of the area specific emission rate of volatile organic compounds (VOCs) from newly produced building products or furnishing under defined climate conditions. The method can also, in principle,

50117,IS,Cor,ISO 16000-9:2006/Cor 1:2007,Indoor air — Part 9: Determination of the emission of volatile organic compounds from building products and furnishing — Emission test chamber method — Technical Corrigendum 1,Air intérieur — Partie 9: Dosage de l'émission de composés organiques volatils de produits de construction et d'objets d'équipement — Méthode de la chambre d'essai d'émission — Rectificatif technique 1,2007-09-10,1,['13.040.20'],ISO/TC 146/SC 6,9599,,[79022],"['en','fr']",1,

39664,IS,,ISO 16001:2008,Earth-moving machinery — Hazard detection systems and visual aids — Performance requirements and tests,Engins de terrassement — Dispositifs de détection des risques et d'aide visuelle — Exigences de performances et essais,2008-02-25,1,['53.100'],ISO/TC 127/SC 2,9599,,[63688],"['en','fr']",50,"<p>ISO 16001:2008 specifies general requirements and describes methods for evaluating and testing the performance of hazard detection systems (HDS) and visual aids (VA) used on earth-moving machines. It covers the following aspects: detection of people in the detection zone; visual and/or audible warning(s) to the operator and/or to the persons in the detection zone; operational

41107,IS,,ISO 16004:2005,Aircraft ground equipment — Passenger boarding bridge or transfer vehicle — Requirements for interface with aircraft doors,Matériel au sol pour aéronefs — Passerelle passagers ou autobus élévateur — Exigences d'interface avec les portes d'aéronefs,2005-04-21,1,['49.100'],ISO/TC 20/SC 9,9599,,[71421],"['en','fr']",6,"<p>ISO 16004:2005 specifies dimensional interface and unobstructed space requirements applicable to the aircraft mating section of either passenger boarding bridges or passenger transfer vehicles used at airports for boarding and disembarkation of passengers on the types of civil transport aircraft listed below. These types of aircraft have a door sill he

40110,IS,,ISO 16010:2005,Elastomeric seals — Material requirements for seals used in pipes and fittings carrying gaseous fuels and hydrocarbon fluids,Garnitures d'étanchéité en élastomères — Exigences matérielles pour les joints utilisés dans les canalisations et les raccords véhiculant des combustibles gazeux et des hydrocarbures liquides,2005-07-19,1,['83.140.50'],ISO/TC 45/SC 4,9599,"[12803,12804]",[77357],"['en','fr']",11,"<p>ISO 16010:2005 specifies requirements for elastomeric materials used in seals for supply pipes and fittings, ancillaries and valves at operating temperatures in general from -5 °C up to 50 °C and in special cases from -15 °C up to 50 °C, for the following:</p><p>a)

28687,IS,,ISO 16012:2004,Plastics — Determination of linear dimensions of test specimens,Plastiques — Détermination des dimensions linéaires des éprouvettes,2004-07-08,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[63481],"['en','fr']",7,<p>ISO 16012:2004 specifies measuring equipment and procedures for the determination of the linear dimensions of solid plastics test specimens.</p>

43553,IS,Cor,ISO 16012:2004/Cor 1:2005,Plastics — Determination of linear dimensions of test specimens — Technical Corrigendum 1,Plastiques — Détermination des dimensions linéaires des éprouvettes — Rectificatif technique 1,2005-11-25,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[63481],"['en','fr']",1,

28935,IS,,ISO 16014-1:2003,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 1: General principles,Plastiques — Détermination de la masse moléculaire moyenne et de la répartition des masses moléculaires des polymères par chromatographie d'exclusion stérique — Partie 1: Principes généraux,2003-04-01,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[52892],['en'],16,<p>ISO 16014-1:2003 specifies a general method for determining the average molecular mass and the molecular mass distribution of polymers using size-exclusion chromatography (SEC). The average molecular mass and the molecular mass distribution are calculate

43283,IS,Cor,ISO 16014-1:2003/Cor 1:2005,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 1: General principles — Technical Corrigendum 1,Plastiques — Détermination de la masse moléculaire moyenne et de la répartition des masses moléculaires des polymères par chromatographie d'exclusion stérique — Partie 1: Principes généraux — Rectificatif technique 1,2005-09-06,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[52892],['en'],1,

52892,IS,,ISO 16014-1:2012,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 1: General principles,Plastiques — Détermination de la masse moléculaire moyenne et de la distribution des masses moléculaires de polymères par chromatographie d'exclusion stérique — Partie 1: Principes généraux,2012-07-03,2,['83.080.01'],ISO/TC 61/SC 5,9599,"[43283,28935]",[74995],['en'],17,<p>ISO 16014-1:2012 specifies a general method for determining the average molecular mass and the molecular mass distribution of polymers using size-exclusion chromatography (SEC). The average molecular mass and the molecular mass distributio

33332,IS,,ISO 16014-2:2003,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 2: Universal calibration method,Plastiques — Détermination de la masse moléculaire moyenne et de la répartition des masses moléculaires des polymères par chromatographie d'exclusion stérique — Partie 2: Méthode d'étalonnage universelle,2003-05-07,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[52893],['en'],12,"<p>ISO 16014-2:2003 specifies a method for determining the average molecular mass and the molecular mass distribution of polymers using size-exclusion chromatography (SEC). The average molecular mass and the molecular mass distribut

52893,IS,,ISO 16014-2:2012,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 2: Universal calibration method,Plastiques — Détermination de la masse moléculaire moyenne et de la distribution des masses moléculaires de polymères par chromatographie d'exclusion stérique — Partie 2: Méthode d'étalonnage universelle,2012-07-03,2,['83.080.01'],ISO/TC 61/SC 5,9599,[33332],[74996],['en'],12,<p>ISO 16014-2:2012 specifies a method for determining the average molecular mass and the molecular mass distribution of polymers using size-exclusion chromatography (SEC). The average molecular mass and the molecular mass dis

29803,IS,,ISO 16014-3:2003,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 3: Low-temperature method,Plastiques — Détermination de la masse moléculaire moyenne et de la répartition des masses moléculaires des polymères par chromatographie d'exclusion stérique — Partie 3: Mesurage aux basses températures,2003-04-01,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[52894],['en'],11,<p>ISO 16014-3:2003 specifies a method for determining the average molecular mass and the molecular mass distribution of polymers using size-exclusion chromatography (SEC) with organic eluent at a temperature lower than 60 °C. The average

52894,IS,,ISO 16014-3:2012,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 3: Low-temperature method,Plastiques — Détermination de la masse moléculaire moyenne et de la distribution des masses moléculaires de polymères par chromatographie d'exclusion stérique — Partie 3: Mesurage aux basses températures,2012-07-03,2,['83.080.01'],ISO/TC 61/SC 5,9599,[29803],[74997],['en'],17,"<p>ISO 16014-3:2012 specifies a method for determining the average molecular mass and the molecular mass distribution of polymers by size-exclusion chromatography (SEC) using an organic eluent at a temperature lower than 60 °C. The

29802,IS,,ISO 16014-4:2003,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 4: High-temperature method,Plastiques — Détermination de la masse moléculaire moyenne et de la répartition des masses moléculaires des polymères par chromatographie d'exclusion stérique — Partie 4: Mesurage aux températures élevées,2003-04-15,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[52895],['en'],12,<p>ISO 16014-4:2003 specifies a method for determining the average molecular mass and the molecular mass distribution of polymers by size-exclusion chromatography (SEC) using an organic eluent at temperatures between 60 °C and 180 °C. Th

52895,IS,,ISO 16014-4:2012,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 4: High-temperature method,Plastiques — Détermination de la masse moléculaire moyenne et de la distribution des masses moléculaires de polymères par chromatographie d'exclusion stérique — Partie 4: Mesurage aux températures élevées,2012-07-03,2,['83.080.01'],ISO/TC 61/SC 5,9599,[29802],[74998],['en'],14,"<p>ISO 16014-4:2012 specifies a method for determining the average molecular mass and the molecular mass distribution of polymers by size-exclusion chromatography (SEC) using an organic eluent at temperatures between 60 °C and 18

52335,IS,,ISO 16014-5:2012,Plastics — Determination of average molecular mass and molecular mass distribution of polymers using size-exclusion chromatography — Part 5: Method using light-scattering detection,Plastiques — Détermination de la masse moléculaire moyenne et de la distribution des masses moléculaires de polymères par chromatographie d'exclusion stérique — Partie 5: Méthode utilisant la détection par diffusion lumineuse,2012-07-02,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[74999],"['en','fr']",24,

28850,IS,,ISO 16016:2000,Technical product documentation — Protection notices for restricting the use of documents and products,Documentation technique de produits — Symboles et clauses de protection utilisés pour les documents et produits dont l'usage est réservé,2000-09-21,1,['01.110'],ISO/TC 10/SC 1,9599,,[65277],"['en','fr']",6,

29832,IS,,ISO 16021:2000,Urine-absorbing aids — Basic principles for evaluation of single-use adult-incontinence-absorbing aids from the perspective of users and caregivers,Aides pour absorption d'urine — Principes de base pour l'évaluation des aides pour incontinents adultes par les utilisateurs et le personnel soignant,2000-11-09,1,['11.180.20'],ISO/TC 173/SC 3,9599,,[84852],"['en','fr']",11,

29852,IS,,ISO 16028:1999,"Hydraulic fluid power — Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) — Specifications","Transmissions hydrauliques — Raccords rapides de type à face plane pour usage à des pressions de 20 MPa (200 bar) à 31,5 MPa (315 bar) — Spécifications",1999-12-16,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[82506],"['en','fr']",5,

41713,IS,Amd,ISO 16028:1999/Amd 1:2006,"Hydraulic fluid power — Flush-face type, quick-action couplings for use at pressures of 20 MPa (200 bar) to 31,5 MPa (315 bar) — Specifications — Amendment 1","Transmissions hydrauliques — Raccords rapides de type à face plane pour usage à des pressions de 20 MPa (200 bar) à 31,5 MPa (315 bar) — Spécifications — Amendement 1",2006-01-09,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[82506],"['en','fr']",1,

29554,IS,,ISO 16030:2001,Pneumatic fluid power — Connections — Ports and stud ends,Transmissions pneumatiques — Raccordements — Orifices et éléments mâles,2001-12-20,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[81907],"['en','fr']",13,"<p>This International Standard specifies dimensions and performance requirements for ports and stud ends with</p><p>parallel threads for pneumatic fluid power applications.</p><p>It specifies reusable, positively retained seals for leak-free connections, for use at pressures from ? 0,09 MPa</p><p>(? 0,9 bar 1)) up to 1,6 MPa (16 bar).</p><p>Only this International Standard is applicable for threaded ports and stud ends specified in new designs in</p><p>pneumatic flu

40208,IS,Amd,ISO 16030:2001/Amd 1:2005,Pneumatic fluid power — Connections — Ports and stud ends — Amendment 1,Transmissions pneumatiques — Raccordements — Orifices et éléments mâles — Amendement 1,2005-04-12,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[81907],"['en','fr']",1,

29867,IS,,ISO 16032:2004,Acoustics — Measurement of sound pressure level from service equipment in buildings — Engineering method,Acoustique — Mesurage du niveau de pression acoustique des équipements techniques dans les bâtiments — Méthode d'expertise,2004-09-15,1,"['91.140.01','91.120.20','17.140.20']",ISO/TC 43/SC 2,9599,,[83874],['en'],19,"<p>ISO 16032:2004 specifies methods for measuring the sound-pressure level produced by service equipment attached to or installed in buildings. It specifically covers measurements on sanitary installations, mechanical ventilation, heating and cooling service equipment, lifts, rubbish chutes, boilers, blowers, pumps and other auxiliary service equipment

37078,IS,,ISO 16038:2005,Rubber condoms — Guidance on the use of ISO 4074 in the quality management of natural rubber latex condoms,Préservatifs en caoutchouc — Directives sur l'utilisation de l'ISO 4074 dans le management de la qualité des préservatifs en latex de caoutchouc naturel,2005-11-02,1,['11.200'],ISO/TC 157,9599,,"[50170,68333]","['en','fr','ru']",11,"<p>ISO 16038:2005 provides guidance on using ISO 4074 and addresses quality issues to be considered during the development, manufacture, quality verification and procurement of condoms. It encompasses the aspects of quality management systems in design, manufacture and delivery of condoms with emphasis on performance, safety and reli

6197,IS,,ISO 1604:1976,Endless wide V-belts for industrial speed-changers and groove profiles for corresponding pulleys,Courroies trapézoïdales larges sans fin pour variateurs de vitesse industriels et profil de gorge des poulies correspondantes,1976-08-01,1,['21.220.10'],ISO/TC 41,9599,,[6198],"['en','fr']",6,

30033,IS,,ISO 16049-1:2001,Air cargo equipment — Restraint straps — Part 1: Design criteria and testing methods,Équipement pour le fret aérien — Sangles d'arrimage — Partie 1: Critères de conception et méthodes d'essai,2001-07-19,1,['49.120'],ISO/TC 20/SC 9,9599,,[53817],"['en','fr']",17,

53817,IS,,ISO 16049-1:2013,Air cargo equipment — Restraint straps — Part 1: Design criteria and testing methods,Équipement pour le fret aérien — Sangles d'arrimage — Partie 1: Critères de conception et méthodes d'essai,2013-03-01,2,['49.120'],ISO/TC 20/SC 9,9599,[30033],[74303],['en'],19,"<p>ISO 16049-1:2013 specifies the design criteria and testing methods adequate to guarantee the ultimate load and operational dependability of cargo restraint strap assemblies with a typical rated ultimate tension load capability of 22 250 N (5 000 lbf), as used by the airline industry in order to restrain on board civil transport aircraft during flight:</p><p>a) cargo loaded and tied down onto airw

33731,IS,,ISO 16049-2:2005,Air cargo equipment — Restraint straps — Part 2: Utilization guidelines and lashing calculations,Équipement de fret aérien — Sangles d'arrimage — Partie 2: Directives pour l'utilisation et calculs d'arrimage,2005-01-07,1,['49.120'],ISO/TC 20/SC 9,9599,,[54922],"['en','fr']",15,"<p>ISO 16049-2:2005 specifies utilization guidelines and principles to be used in strength calculation methods adequate to guarantee the effectiveness and ultimate load strength of tie-down/lashing arrangements used to restrain cargo on board civil transport aircraft during flight for either cargo loaded and tied down onto airworthiness certified air cargo pallets, themselves restrained into

54922,IS,,ISO 16049-2:2013,Air cargo equipment — Restraint straps — Part 2: Utilization guidelines and lashing calculations,Équipement de fret aérien — Sangles d'arrimage — Partie 2: Directives pour l'utilisation et calculs d'arrimage,2013-05-13,2,['49.120'],ISO/TC 20/SC 9,9599,[33731],[70673],['en'],14,"<p>ISO 16049-2:2013 provides general utilization guidelines and calculation methods adequate to guarantee the effectiveness and ultimate load strength of tie-down/lashing arrangements performed to restrain cargo on board civil transport aircraft during flight:</p><p>a) cargo loaded and tied down onto airworthiness approved air cargo pallets, themselves restrained into aircraft lower

29494,IS,,ISO 16053:2004,Paints and varnishes — Coating materials and coating systems for exterior wood — Natural weathering test,Peintures et vernis — Produits de peinture et systèmes de peinture pour bois en extérieur — Essai de vieillissement naturel,2004-06-23,1,['87.040'],ISO/TC 35/SC 9,9599,,[50492],"['en','fr','ru']",20,<p>ISO 16053:2004 specifies a natural weathering test for exterior wood coating systems mainly intended for decoration and protection of planed and sawn wood.</p><p>The test provides a means of evaluating the performance of a wood coating system during outdoor exposure. It forms the basis for the performance specification given by ENV 927-2.</p>

50492,IS,,ISO 16053:2010,Paints and varnishes — Coating materials and coating systems for exterior wood — Natural weathering test,Peintures et vernis — Produits de peinture et systèmes de peinture pour bois en extérieur — Essai de vieillissement naturel,2010-02-11,2,['87.040'],ISO/TC 35/SC 9,9599,[29494],[70859],"['en','ru']",21,<p>ISO 16053:2010 specifies a natural weathering test for exterior wood coating systems mainly intended for decoration and protection of planed and sawn wood.</p><p>The test provides a means of evaluating the performance of a wood coating system during outdoor exposure. It forms the basis for the performance specification given in EN 927-2.</p>

70859,IS,,ISO 16053:2018,Paints and varnishes — Coating materials and coating systems for exterior wood — Natural weathering test,Peintures et vernis — Produits de peinture et systèmes de peinture pour bois en extérieur — Essai de vieillissement naturel,2018-09-12,3,['87.040'],ISO/TC 35/SC 9,9599,[50492],[82706],['en'],22,<p>This document specifies a natural weathering test for exterior wood coating systems mainly intended for the decoration and protection of planed and sawn wood.</p><p>The test provides a means of evaluating the performance of a wood coating system during outdoor exposure. It forms the basis for the performance specification in accordance with EN 927-2.</p>

30045,IS,,ISO 16054:2000,Implants for surgery — Minimum data sets for surgical implants,Implants chirurgicaux — Ensembles minimaux de données relatives aux implants chirurgicaux,2000-12-21,1,['11.040.40'],ISO/TC 150,9599,,"[69882,59182]","['en','fr']",4,

29553,IS,,ISO 16055:2003,Tobacco and tobacco products — Monitor test piece — Requirements and use,Tabac et produits du tabac — Éprouvette de contrôle — Exigences et utilisation,2003-02-24,1,['65.160'],ISO/TC 126,9599,,[56766],"['en','fr']",13,<p>ISO 16055:2003 describes the requirements for a monitor test piece as well as its use. A monitor test piece is a cigarette taken from a batch produced under particularly strictly controlled manufacturing conditions and used to monitor the stability of the analytical processes involved when using a cigarette-smoking machine for routine analyses.</p>

56766,IS,,ISO 16055:2012,Tobacco and tobacco products — Monitor test piece — Requirements and use,Tabac et produits du tabac — Éprouvette de contrôle — Exigences et utilisation,2012-12-14,2,['65.160'],ISO/TC 126,9599,[29553],[75604],"['en','fr']",17,<p>ISO 16055:2012 describes the requirements for a monitor test piece as well as its use.</p>

75604,IS,,ISO 16055:2019,Tobacco and tobacco products — Monitor test piece — Requirements and use,Tabac et produits du tabac — Éprouvette de contrôle — Exigences et utilisation,2019-03-18,3,['65.160'],ISO/TC 126,9599,[56766],[78174],"['en','fr']",17,<p>This document describes the requirements for a monitor test piece as well as its use.</p>

30842,IS,,ISO 16061:2000,Instrumentation for use in association with non-active surgical implants — General requirements,Instrumentation à utiliser en association avec les implants chirurgicaux non actifs — Exigences générales,2000-03-16,1,"['11.040.99','11.040.40']",ISO/TC 150,9599,,[44996],"['en','fr']",19,

44996,IS,,ISO 16061:2008,Instrumentation for use in association with non-active surgical implants — General requirements,Instrumentation à utiliser en association avec les implants chirurgicaux non actifs — Exigences générales,2008-11-25,2,"['11.040.99','11.040.40']",ISO/TC 150,9599,[30842],[62113],"['en','fr']",19,"<p>ISO 16061:2008 specifies general requirements for instruments to be used in association with non-active surgical implants. These requirements apply to instruments when they are manufactured and when they are resupplied after refurbishment.</p><p>ISO 16061:2008 also applies to instruments which may be connected to power-driven systems, but does not apply to the power-driven sys

62113,IS,,ISO 16061:2015,Instrumentation for use in association with non-active surgical implants — General requirements,Instrumentation à utiliser en association avec les implants chirurgicaux non actifs — Exigences générales,2015-05-11,3,"['11.040.99','11.040.40']",ISO/TC 150,9599,[44996],[74548],"['en','fr']",19,"<p>ISO 16061:2015 specifies general requirements for instruments to be used in association with non-active surgical implants. These requirements apply to instruments when they are manufactured and when they are resupplied after refurbishment.</p><p>This International Standard also applies to instruments which may be connected to power-driven systems, but does not apply to the pow

30113,IS,,ISO 16065-1:2001,Pulps — Determination of fibre length by automated optical analysis — Part 1: Polarized light method,Pâtes — Détermination de la longueur de fibre par analyse optique automatisée — Partie 1: Méthode de la lumière polarisée,2001-09-27,1,['85.040'],ISO/TC 6,9599,,[60368],"['en','fr']",9,

32892,IS,,ISO 16065-2:2007,Pulps — Determination of fibre length by automated optical analysis — Part 2: Unpolarized light method,Pâtes — Détermination de la longueur de fibre par analyse optique automatisée — Partie 2: Méthode de la lumière non polarisée,2007-01-15,1,['85.040'],ISO/TC 6,9599,,[60375],"['en','fr','ru']",9,"<p>ISO 16065-2:2007 specifies a method for determining fibre length by automated optical analysis, using unpolarized light.</p><p>The method is applicable to all kinds of pulp. However, fibrous particles shorter than 0,2 mm are not regarded as fibres for the purposes of ISO 16065-2:2007 and therefore are not included in the results.</p>"

30124,IS,,ISO 16069:2004,Graphical symbols — Safety signs — Safety way guidance systems (SWGS),Symboles graphiques — Signaux de sécurité — Systèmes de guidage pour cheminement d'évacuation de sécurité,2004-10-29,1,"['01.080.10','01.080.20']",ISO/TC 145/SC 2,9599,,[66837],"['en','fr']",51,"<p>ISO 16069:2004 describes the principles governing the design and application of visual components used to create a safety way guidance system (SWGS).</p><p>ISO 16069:2004 contains general principles valid both for electrically powered and for phosphorescent components. Special information which is related to the type of component is given to assist in defining the environment of use, choice of material,

6199,IS,,ISO 1607-1:1980,Positive-displacement vacuum pumps — Measurement of performance characteristics — Part 1: Measurement of volume rate of flow (pumping speed),Pompes primaires volumétriques à vide — Mesurage des caractéristiques fonctionnelles — Partie 1: Mesurage du débit-volume,1980-02-01,1,['23.160'],ISO/TC 112,9599,,[6200],"['en','fr']",3,

6200,IS,,ISO 1607-1:1993,Positive-displacement vacuum pumps — Measurement of performance characteristics — Part 1: Measurement of volume rate of flow (pumping speed),Pompes primaires volumétriques à vide — Mesurage des caractéristiques fonctionnelles — Partie 1: Mesurage du débit-volume,1993-11-25,2,['23.160'],ISO/TC 112,9599,[6199],"[50844,36111]","['en','fr']",3,<p>The method of determining the volume of gas which flows in unit time through the pump inlet are specified. The considered pumps discharge the gas against atmosphere pressure and achieve a limiting inlet pressure less than 100 pa in one stage.</p>

6201,IS,,ISO 1607-2:1978,Positive displacement vacuum pumps — Measurement of performance characteristics — Part 2: Measurement of ultimate pressure,Pompes primaires volumétriques à vide — Mesurage des caractéristiques fonctionnelles — Partie 2: Mesurage de la pression limite,1978-09-01,1,['23.160'],ISO/TC 112,9599,,[6202],"['en','fr']",3,

6202,IS,,ISO 1607-2:1989,Positive-displacement vacuum pumps — Measurement of performance characteristics — Part 2: Measurement of ultimate pressure,Pompes primaires volumétriques à vide — Mesurage des caractéristiques fonctionnelles — Partie 2: Mesurage de la pression limite,1989-10-19,2,['23.160'],ISO/TC 112,9599,[6201],"[36112,50844]","['en','fr']",3,<p>The considered pumps discharge the gas against atmosphere pressure and achieve a limiting inlet pressure of less than 100 Pa in one stage. The method adopted is that the ultimate pressure is measured at a specified temperature in a specified form of test dome attached to the inlet of the pump.</p>

30856,IS,,ISO 16070:2001,Petroleum and natural gas industries — Downhole equipment — Lock mandrels and landing nipples,Industries du pétrole et du gaz naturel — Équipement de fond de trou — Mandrins à clé d'ancrage et sièges d'ancrage,2001-12-20,1,['75.180.10'],ISO/TC 67/SC 4,9599,,[39196],['en'],24,"<p>La présente Norme internationale définit les exigences en matière de mandrins à clefs d'ancrage et de sièges d'ancrage utilisés dans les complétions des puits producteurs ou injecteurs pour l'installation d'équipements de contrôle de débit ou d'autres équipements employés par les industries du pétrole et du gaz naturel. Elle prend en compte les filetages assurant l'interface entre les mandrin

37696,IS,,ISO 16073:2011,Wildland firefighting personal protective equipment — Requirements and test methods,Équipement de protection individuelle pour la lutte contre les feux d'espaces naturels — Exigences et méthodes d'essai,2011-02-07,1,"['13.340.10','13.220.10']",ISO/TC 94/SC 14,9599,,"[74215,74212,74209,74216,74213,74210,74214,74211]",['en'],72,"<p>ISO 16073:2011 specifies the minimum performance requirements and methods of test for personal protective equipment (PPE) covering the torso, neck, arms, hands, legs, feet, head, eyes and hearing for wildland firefighting. </p><p>It covers the general design of the PPE, the minimum levels of performance for the materials employed and the met

62756,IS,,ISO 16075-1:2015,Guidelines for treated wastewater use for irrigation projects — Part 1: The basis of a reuse project for irrigation,Lignes directrices pour l'utilisation des eaux usées traitées en irrigation — Partie 1: Les bases d'un projet de réutilisation en irrigation,2015-08-13,1,"['13.060.30','13.060.01']",ISO/TC 282/SC 1,9599,[62757],[73482],"['en','fr']",31,"<p>ISO 16075-1:2015 contains guidelines for the development and the execution of projects intending to use treated wastewater (TWW) for irrigation and considers the parameters of climate and soil.</p><p>The purpose of these guidelines is to provide specifications for all elements of a project using TWW for irrigation,

62758,IS,,ISO 16075-2:2015,Guidelines for treated wastewater use for irrigation projects — Part 2: Development of the project,Lignes directrices pour l'utilisation des eaux usées traitées en irrigation — Partie 2: Développement du projet,2015-08-13,1,"['13.060.30','13.060.01']",ISO/TC 282/SC 1,9599,,[73483],"['en','fr']",24,"<div id='MathJax_Message' style='display: none;'></div><p>ISO 16075-2:2015 covers the following issues:</p><ul><li>criteria for the design of treated wastewater (herinafter: TWW) irrigation projects intended to prevent public health risks within the population that has been in direct or indirect contact with the TWW or with any product that has come in contact with the T

62759,IS,,ISO 16075-3:2015,Guidelines for treated wastewater use for irrigation projects — Part 3: Components of a reuse project for irrigation,Lignes directrices pour l'utilisation des eaux usées traitées en irrigation — Partie 3: Éléments d'un projet de réutilisation en irrigation,2015-08-13,1,"['13.060.30','13.060.01']",ISO/TC 282/SC 1,9599,,[73484],"['en','fr']",38,"<p>ISO 16075-3:2015 covers the system's components needed for the use of TWW for irrigation which relate to various pressure and open irrigation systems specifically drip irrigation as this method represents an efficient method of water delivery and water saving. Despite the fact that water quality and filtration of treated w

62760,IS,,ISO 16075-4:2016,Guidelines for treated wastewater use for irrigation projects — Part 4: Monitoring,Lignes directrices pour l'utilisation des eaux usées traitées en irrigation — Partie 4: Surveillance,2016-12-13,1,"['13.060.30','13.060.01']",ISO/TC 282/SC 1,9599,,[73485],"['en','fr']",21,"<p>ISO 16075-4:2016 provides recommendations regarding:</p><p>· monitoring the quality of treated wastewater (TWW) for irrigation;</p><p>· monitoring irrigated plants;</p><p>· monitoring the soil with regard to salinity;</p><p>· monitoring natural water sources in neighbouring environments;</p><p>· monitoring the quality of water in storage reservoirs.</p><p

55634,IS,,ISO 16079-1:2017,Condition monitoring and diagnostics of wind turbines — Part 1: General guidelines,Surveillance et diagnostic d'état des éoliennes de production d'électricité — Partie 1: Lignes directrices générales,2017-11-03,1,['27.180'],ISO/TC 108/SC 5,9599,,[88268],"['en','fr']",23,"<p>ISO 16079-1:2017 gives guidelines which provide the basis for choosing condition monitoring methods used for failure mode detection, diagnostics and prognostics of wind power plant components.</p>"

6204,IS,,ISO 1608-1:1980,Vapour vacuum pumps — Measurement of performance characteristics — Part 1: Measurement of volume rate of flow (pumping speed),Pompes à vide à jet de vapeur — Mesurage des caractéristiques fonctionnelles — Partie 1: Mesurage du débit-volume,1980-02-01,1,['23.160'],ISO/TC 112,9599,,[6205],"['en','fr']",3,

6206,IS,,ISO 1608-2:1978,Vapour vacuum pumps — Measurement of performance characteristics — Part 2: Measurement of critical backing pressure,Pompes à vide à jet de vapeur — Mesurage des caractéristiques fonctionnelles — Partie 2: Mesurage de la pression critique de refoulement,1978-12-01,1,['23.160'],ISO/TC 112,9599,,[6207],"['en','fr']",3,

55665,IS,,ISO 16089:2015,Machine tools — Safety — Stationary grinding machines,Machines-outils — Sécurité — Machines à meuler fixes,2015-11-16,1,['25.080.01'],ISO/TC 39/SC 10,9599,,[83110],"['en','fr']",132,"<p>ISO 16089:2015 specifies the requirements and/or measures to eliminate the hazards or reduce the risks in the following groups of stationary grinding machines which are designed primarily to shape metal by grinding:</p><p>Group 1: Manually controlled grinding machines without power operated axes and without numerical control.</p><p>Group 2: Manually controlled grinding machines with power operated axes and limited numerically controlled capability, if applicable.</p><p>Group 3: Numeri

6209,IS,,ISO 1609:1986,Vacuum technology — Flange dimensions,Technique du vide — Dimensions des brides,1986-03-06,1,['23.160'],ISO/TC 112,9599,,"[79408,6210]","['en','fr']",8,"<p>The specified dimensions ensure interchangeability between bolted, clamped and rotable flanges under special conditions. The main dimensions are tabled; linear sealing loads, bores for vacuum flanges and required outside tube diameters are specified.</p>"

55666,IS,,ISO 16090-1:2017,"Machine tools safety — Machining centres, Milling machines, Transfer machines — Part 1: Safety requirements","Sécurité des machines-outils — Centres d'usinage, fraiseuses, machines transfert — Partie 1: Exigences de sécurité",2017-12-08,1,['25.080.01'],ISO/TC 39/SC 10,9599,,[81558],"['en','fr']",153,"<p>ISO 16090-1:2017 specifies the technical safety requirements and protective measures for the design, construction and supply (including installation and dismantling, with arrangements for transport and maintenance) of stationary milling machines (see 3.1.1), including machines capable of performing boring operations (see 3.1.2), machining centres and transfer machi

30863,IS,,ISO 16091:2002,Space systems — Integrated logistic support,Systèmes spatiaux — Soutien logistique intégré,2002-11-27,1,['49.140'],ISO/TC 20/SC 14,9599,,[72937],"['en','fr']",22,"<p>ISO 16091:2002 describes the set of management requirements needed to identify and provide logistic support, so the customer can operate and maintain a product in its operational environment for the expected lifetime.</p><p>These requirements also aim, throughout the product life cycle, at implementing everything pertinent to the control of the risks considered as critical regarding the operational objectives.</p><p>The management requirements are applicable to those activities necessary to design, devel

3992,IS,,ISO 161-1:1978,Thermoplastics pipes for the transport of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series,Tubes en matières thermoplastiques pour le transport des fluides — Diamètres extérieurs nominaux et pressions nominales — Partie 1: Série métrique,1978-04-01,2,['23.040.20'],ISO/TC 138,9599,,[23607],"['en','fr']",2,

23607,IS,,ISO 161-1:1996,Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series,Tubes en matières thermoplastiques pour le transport des fluides — Diamètres extérieurs nominaux et pressions nominales — Partie 1: Série métrique,1996-12-26,3,['23.040.20'],ISO/TC 138,9599,[3992],[65253],"['en','fr']",4,<p>Specifies the nominal outside diameters for metric thermoplastics pipes for the conveyance of fluids under pressure and non-pressure. It also specifies nominal pressure ratings and minimum required strengths for pipes for pressure applications.</p>

3994,IS,,ISO 161-2:1977,Thermoplastic pipes for the transport of fluids — Nominal outside diameters and nominal pressures — Part 2: Inch series,Tubes en thermoplastiques pour le transport des fluides — Diamètres extérieurs nominaux et pressions nominales — Partie 2: Série en inches,1977-09-01,1,['23.040.20'],ISO/TC 138,9599,[4273],[24510],"['en','fr']",2,

35156,IS,,ISO 16100-1:2002,Industrial automation systems and integration — Manufacturing software capability profiling for interoperability — Part 1: Framework,Systèmes d'automatisation industrielle et intégration — Profil d'aptitude du logiciel de fabrication pour interopérabilité — Partie 1: Cadre,2002-11-29,1,['25.040.01'],ISO/TC 184/SC 5,9599,,[53378],['en'],52,"<p>Part 1 of ISO 16100 specifies a framework for the interoperability of a set of software products used in the manufacturing domain and to facilitate its integration into a manufacturing application (see Annex A for a discussion of a manufacturing application). This framework addresses information exchange models, software objec

55213,IS,,ISO 16100-6:2011,Industrial automation systems and integration — Manufacturing software capability profiling for interoperability — Part 6: Interface services and protocols for matching profiles based on multiple capability class structures,Systèmes d'automatisation industrielle et intégration — Profil d'aptitude du logiciel de fabrication pour interopérabilité — Partie 6: Services d'interface et protocoles pour la correspondance des profils fondés sur les structures de classe d'aptitude multiple,2011-06-07,1,['25.040.01'],ISO/TC 184/SC 5,9599,,[73656],['en'],70,"<p>ISO 16100-6:2011 defines the detailed interface services and protocols used in a matching method based on multiple ca

30131,IS,,ISO 16101:2004,Packaging — Transport packaging for dangerous goods — Plastics compatibility testing,Emballages — Emballages pour le transport des marchandises dangereuses — Essais de compatibilité des matières plastiques,2004-09-15,1,"['13.300','55.020']",ISO/TC 122/SC 3,9599,,[53591],"['en','fr']",67,"<p>ISO 16101:2004 specifies the requirements and test methods for compatibility testing of polyethylene based plastics packagings and composite packagings with plastic inners containing liquids. The testing involves storage with the packaged substance, or with a standard liquid as defined in Annex A. Annex B describes small scale laboratory tests which may be used to determine the as

30134,IS,,ISO 16104:2003,Packaging — Transport packaging for dangerous goods — Test methods,Emballage — Emballage de transport pour marchandises dangereuses — Méthodes d'essai,2003-05-20,1,"['13.300','55.020']",ISO/TC 122/SC 3,9599,,[56877],['en'],47,<p>ISO 16104:2003 specifies the design type test requirements for packagings intended for use in the transport of dangerous goods.</p>

39762,IS,,ISO 16106:2006,"Packaging — Transport packages for dangerous goods — Dangerous goods packagings, intermediate bulk containers (IBCs) and large packagings — Guidelines for the application of ISO 9001","Emballage — Emballages de transport pour marchandises dangereuses — Emballages pour marchandises dangereuses, grands récipients vrac (GRV) et grands emballages — Directives pour l'application de l'ISO 9001",2006-03-02,1,"['13.300','55.020']",ISO/TC 122/SC 3,9599,,[69053],"['ar','en','fr']",27,"<p>ISO 16106:2006 gives guidance on quality management provisions applicable to the manufacture, measuring and monitoring of design type approved dangerous goods packagings, intermediate bulk co

30138,IS,,ISO 16107:1999,Workplace atmospheres — Protocol for evaluating the performance of diffusive samplers,Air des lieux de travail — Protocole pour l'évaluation de la performance des dispositifs de prélèvement par diffusion,1999-09-30,1,['13.040.30'],ISO/TC 146/SC 2,9599,,[41966],['en'],15,

50366,IS,,ISO 16111:2008,Transportable gas storage devices — Hydrogen absorbed in reversible metal hydride,Appareils de stockage de gaz transportables — Hydrogène absorbé dans un hydrure métallique réversible,2008-11-14,1,['71.100.20'],ISO/TC 197,9599,[37723],[67952],"['en','fr']",38,"<p>ISO 16111:2008 defines the requirements applicable to the material, design, construction, and testing of transportable hydrogen gas storage systems, referred to as “metal hydride assemblies” (MH assemblies) which utilize shells not exceeding 150 l internal volume and having a maximum developed pressure (MDP) not exceeding 25 MPa (250 bar). </p><p>It only applies to refillable storage MH assemblies where hydr

37724,IS,,ISO 16112:2006,Compacted (vermicular) graphite cast irons — Classification,Fontes à graphite vermiculaire (compacté) — Classification,2006-08-07,1,['77.080.10'],ISO/TC 25,9599,,[67755],"['en','fr']",23,"<p>ISO 16112:2006 specifies five grades of compacted (vermicular) graphite cast irons.</p><p>ISO 16112:2006 specifies five grades based on the minimum mechanical properties measured on machined test pieces prepared from</p><ul><li>separately cast samples,</li><li>cast-on samples, or</li><li>samples cut from a casting.</li></ul>"

30150,IS,,ISO 16120-1:2001,Non-alloy steel wire rod for conversion to wire — Part 1: General requirements,Fil-machine en acier non allié destiné à la fabrication de fils — Partie 1: Exigences générales,2001-08-30,1,['77.140.60'],ISO/TC 17/SC 17,9599,[15647],[45631],['en'],10,

45631,IS,,ISO 16120-1:2011,Non-alloy steel wire rod for conversion to wire — Part 1: General requirements,Fil-machine en acier non allié destiné à la fabrication de fils — Partie 1: Exigences générales,2011-06-29,2,['77.140.60'],ISO/TC 17/SC 17,9599,[30150],[63741],"['en','fr','ru']",21,"<p>ISO 16120:2011 is applicable to wire rod of non-alloy steel intended for wire drawing and/or cold rolling. The cross-section can be circular, oval, square, rectangular, hexagonal, octagonal, half-round or another shape, generally with at least 5 mm nominal dimension, and with a smooth surface.</p><p>ISO 16120-1:2011 covers general requirements and is not applicable to products for which standards exist or

30151,IS,,ISO 16120-2:2001,Non-alloy steel wire rod for conversion to wire — Part 2: Specific requirements for general purpose wire rod,Fil-machine en acier non allié destiné à la fabrication de fils — Partie 2: Exigences spécifiques au fil-machine d'usage général,2001-08-30,1,['77.140.60'],ISO/TC 17/SC 17,9599,[15647],[45632],['en'],3,

45632,IS,,ISO 16120-2:2011,Non-alloy steel wire rod for conversion to wire — Part 2: Specific requirements for general-purpose wire rod,Fil-machine en acier non allié destiné à la fabrication de fils — Partie 2: Exigences spécifiques au fil-machine d'usage général,2011-06-29,2,['77.140.60'],ISO/TC 17/SC 17,9599,[30151],[63742],"['en','fr','ru']",7,<p>ISO 16120-2:2011 is applicable to general-purpose steel wire rod for drawing and/or cold rolling.</p>

30152,IS,,ISO 16120-3:2001,"Non-alloy steel wire rod for conversion to wire — Part 3: Specific requirements for rimmed and rimmed-substitute, low-carbon steel wire rod",Fil-machine en acier non allié destiné à la fabrication de fils — Partie 3: Exigences spécifiques au fil-machine en acier effervescent ou pseudo-effervescent à bas carbone,2001-08-30,1,['77.140.60'],ISO/TC 17/SC 17,9599,[15647],[45633],['en'],3,

30153,IS,,ISO 16120-4:2001,Non-alloy steel wire rod for conversion to wire — Part 4: Specific requirements for wire rod for special applications,Fil-machine en acier non allié destiné à la fabrication de fils — Partie 4: Exigences spécifiques au fil-machine pour applications spéciales,2001-08-30,1,['77.140.60'],ISO/TC 17/SC 17,9599,[15647],[45634],['en'],5,

45634,IS,,ISO 16120-4:2011,Non-alloy steel wire rod for conversion to wire — Part 4: Specific requirements for wire rod for special applications,Fil-machine en acier non allié destiné à la fabrication de fils — Partie 4: Exigences spécifiques au fil-machine pour applications spéciales,2011-06-29,2,['77.140.60'],ISO/TC 17/SC 17,9599,[30153],[63743],"['en','fr','ru']",9,<p>ISO 16120-4:2011 is applicable to steel wire rod with improved characteristics intended for drawing and/or cold rolling.</p>

39118,IS,,ISO 16121-1:2005,"Road vehicles — Ergonomic requirements for the driver's workplace in line-service buses — Part 1: General description, basic requirements","Véhicules routiers — Exigences ergonomiques du poste de conduite dans les bus de ville — Partie 1: Description générale, exigences de base",2005-09-28,1,"['13.180','43.080.20']",ISO/TC 22,9599,,[56173],"['en','ru']",13,"<p>ISO 16121-1:2005 applies to the driver's workplace in low-floor line-service buses designed for the carriage of passengers, comprising more than eight seats in addition to the driver's seat, and having a maximum weight exceeding five metric tonnes and an overall width exceeding 2,30 m.</p><p>It contains basi

39119,IS,,ISO 16121-2:2005,Road vehicles — Ergonomic requirements for the driver's workplace in line-service buses — Part 2: Visibility,Véhicules routiers — Exigences ergonomiques du poste de conduite dans les bus de ville — Partie 2: Visibilité,2005-09-28,1,"['13.180','43.080.20']",ISO/TC 22,9599,,[56532],"['en','ru']",6,"<p>ISO 16121-2:2005 applies to the driver's workplace in low-floor line-service buses designed for the carriage of passengers, comprising more than eight seats in addition to the driver's seat, and having a maximum weight exceeding five metric tonnes and an overall width exceeding 2,30 m.</p><p>ISO 16121-2:2005 gives the requirements for the driver's field of view to the a

39120,IS,,ISO 16121-3:2005,Road vehicles — Ergonomic requirements for the driver's workplace in line-service buses — Part 3: Information devices and controls,Véhicules routiers — Exigences ergonomiques du poste de conduite dans les bus de ville — Partie 3: Systèmes de contrôle et d'information,2005-10-06,1,"['13.180','43.080.20']",ISO/TC 22,9599,,[59367],['en'],9,"<p>ISO 16121-3:2005 applies to the driver's workplace in low-floor buses designed for the carriage of passengers, comprising more than eight seats in addition to the driver's seat, and having a maximum weight exceeding five metric tons and a maximum width exceeding 2,30 m. </p><p>It gives the requirements for the location of inform

39121,IS,,ISO 16121-4:2005,Road vehicles — Ergonomic requirements for the driver's workplace in line-service buses — Part 4: Cabin environment,Véhicules routiers — Exigences ergonomiques du poste de conduite dans les bus de ville — Partie 4: Environnement dans la cabine,2005-08-15,1,"['13.180','43.080.20']",ISO/TC 22,9599,,[56533],"['en','ru']",6,"<p>ISO 16121-4:2005 applies to the driver's workplace in low-floor line-service buses designed for the carriage of passengers, comprising more than eight seats in addition to the driver's seat, and having a maximum weight exceeding five metric tonnes and an overall width exceeding 2,30 m.</p><p>It gives the minimum requirements for the cabin enviro

56721,IS,,ISO 16122-1:2015,Agricultural and forestry machinery — Inspection of sprayers in use — Part 1: General,Matériel agricole et forestier — Contrôle des pulvérisateurs en service — Partie 1: Généralités,2015-03-13,1,['65.060.40'],ISO/TC 23/SC 6,9599,,[83366],"['en','fr']",7,"<p>ISO 16122-1:2015 defines the general requirements to be fulfilled for the inspection of all types of sprayers for plant protection products used in agriculture, horticulture, forestry and other areas, except knapsack sprayers (see ISO 19932?1 and ISO 19932?2).</p><p>The specific requirements for the different types of sprayers are defined in the relevant specific parts of ISO 16122. When used in conjunction with

55708,IS,,ISO 16122-2:2015,Agricultural and forestry machinery — Inspection of sprayers in use — Part 2: Horizontal boom sprayers,Matériel agricole et forestier — Contrôle des pulvérisateurs en service — Partie 2: Pulvérisateurs à rampe horizontale,2015-03-13,1,['65.060.40'],ISO/TC 23/SC 6,9599,,[83368],"['en','fr']",18,"<p>ISO 16122-2:2015, when used together with ISO 16122-1, specifies the requirements and test methods for the inspection of horizontal boom sprayers, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application. Requirements for the protection of inspectors d

55709,IS,,ISO 16122-3:2015,Agricultural and forestry machinery — Inspection of sprayers in use — Part 3: Sprayers for bush and tree crops,Matériel agricole et forestier — Contrôle des pulvérisateurs en service — Partie 3: Pulvérisateurs pour cultures arbustives et arboricoles,2015-03-13,1,['65.060.40'],ISO/TC 23/SC 6,9599,,[83370],"['en','fr']",15,"<p>ISO 16122-3:2015, when used together with ISO 16122-1, specifies the requirements and test methods for the inspection of sprayers for bushes and trees, when in use. The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve a good application. Requirements

57415,IS,,ISO 16122-4:2015,Agricultural and forestry machines — Inspection of sprayers in use — Part 4: Fixed and semi-mobile sprayers,Matériel agricole et forestier — Contrôle des pulvérisateurs en service — Partie 4: Pulvérisateurs fixes et semi-mobiles,2015-03-13,1,['65.060.40'],ISO/TC 23/SC 6,9599,,[83371],"['en','fr']",19,"<p>ISO 16122-4:2015, when used together with ISO 16122‑1, specifies the requirements and test methods for the inspection of fixed and semi-mobile sprayers, when in use.</p><p>The requirements relate mainly to the condition of the sprayer with respect to its potential risk for the environment and its performance to achieve good application.</p><p>It does not apply to a

36074,IS,,ISO 16124:2004,Steel wire rod — Dimensions and tolerances,Fil machine en acier — Dimensions et tolérances,2004-09-13,1,['77.140.65'],ISO/TC 17/SC 17,9599,[15646],[59563],"['en','fr']",7,<p>ISO 16124:2004 specifies dimensions and tolerances to the dimensions applicable to steel wire rod as defined in ISO 6929:1987.</p>

55720,IS,,ISO 16126:2014,Space systems — Assessment of survivability of unmanned spacecraft against space debris and meteoroid impacts to ensure successful post-mission disposal,Systèmes spatiaux — Évaluation de la capacité de survie des véhicules spatiaux non habités face aux débris spatiaux et aux impacts de météoroïdes pour garantir une élimination efficace d'après-mission,2014-03-24,1,['49.140'],ISO/TC 20/SC 14,9599,,[78979],"['en','ru']",19,"<p>ISO 16126:2014 defines requirements and a procedure for assessing the survivability of an unmanned spacecraft against space debris and meteoroid impacts to ensure the survival of critical components required to perform post-mission disposal. ISO

55721,IS,,ISO 16127:2014,Space systems — Prevention of break-up of unmanned spacecraft,Systèmes spatiaux — Prévention de l'éclatement des navettes sans pilote,2014-02-13,1,['49.140'],ISO/TC 20/SC 14,9599,,[75221],['en'],9,"<p>ISO 16127:2014 defines the requirements to reduce the risk of in-orbit break-up of unmanned spacecraft, both during and after their operational lives. The aim would be met by reducing the possibility of a break-up caused by an unplanned internally caused event and by depleting to a safe level all the sources of stored energy at the end of a spacecraft's life. ISO 16127:2014 is designed for use in planning, verifying and implementing the prevention of break-up of a space

55727,IS,,ISO 16129:2012,Surface chemical analysis — X-ray photoelectron spectroscopy — Procedures for assessing the day-to-day performance of an X-ray photoelectron spectrometer,Analyse chimique des surfaces — Spectroscopie de photoélectrons X — Modes opératoires d'évaluation de la performance au jour le jour d'un spectromètre de photoélectrons X,2012-04-12,1,['71.040.40'],ISO/TC 201/SC 7,9599,,[74819],['en'],18,

29385,IS,,ISO 16132:2004,Ductile iron pipes and fittings — Seal coats for cement mortar linings,Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements de mortier de ciment,2004-07-08,1,"['23.040.10','77.140.75']",ISO/TC 5/SC 2,9599,,[65495],"['en','fr']",12,"<p>ISO 16132:2004 specifies the requirements for seal coatings for factory application to the surfaces of cement mortar linings, which are factory applied to the interior of ductile iron pipes and fittings.</p><p>It also gives performance test requirements for short term sealing efficiency and long term durability and requirements for routine testing for visual appearance, coating thickness and adhesion.</p><p>ISO 16132:20

65495,IS,,ISO 16132:2016,Ductile iron pipes and fittings — Seal coats for cement mortar linings,Tuyaux et raccords en fonte ductile — Seal coats pour les revêtements de mortier de ciment,2016-04-21,2,"['23.040.10','77.140.75']",ISO/TC 5/SC 2,9599,[29385],[85450],['en'],16,"<p>ISO 16132:2016 specifies the requirements for seal coatings for factory application to the surfaces of cement mortar linings, which are factory applied to the interior of ductile iron pipes and fittings.</p><p>It provides the performance requirements for short-term sealing efficiency, long-term durability and cyclic pressure, as well as the routine testing requirements for visual appearance, coating thickness and adhesi

30868,IS,,ISO 16133:2004,Soil quality — Guidance on the establishment and maintenance of monitoring programmes,Qualité du sol — Lignes directrices pour l'établissement et l'entretien de programmes de surveillance,2004-03-12,1,['13.080.01'],ISO/TC 190/SC 7,9599,,"[68254,62600]","['en','fr']",34,<p>ISO 16133:2004 gives general guidance on the selection of procedures for the establishment and maintenance of programmes for long-term monitoring of soil quality. It takes into account the large number of objectives for soil-monitoring programmes.</p><p>ISO 16133:2004 is intended to help provide a basis for dialogue between parties which might be involved in a monitoring scheme. Examples of soil-mon

40651,IS,,ISO 16134:2006,Earthquake- and subsidence-resistant design of ductile iron pipelines,Conceptions de canalisations en fonte ductile résistant aux tremblements de terre et aux affaissements,2006-02-02,1,['23.040.10'],ISO/TC 5/SC 2,9599,,[77319],['en'],32,"<p>ISO 16134:2006 specifies the design of earthquake- and subsidence-resistant ductile iron pipelines suitable for use in areas where seismic activity and land subsidence can be expected. It provides a means of determining and checking the resistance of buried pipelines and also gives example calculations. It is applicable to ductile iron pipes and fittings with joints that have expansion/contraction and deflection capabilities, use