Withdrawn and superseded ISO standards — page 4 of 246

74448,IS,,ISO 1018:2019,Hard coal — Determination of moisture-holding capacity,Houille — Détermination de la capacité de rétention d'humidité,2019-09-30,2,['73.040'],ISO/TC 27/SC 5,9599,[5488],[86987],['en'],2,<p>This document gives reference to ASTM D1412 as a method of determining the moisture-holding capacity of hard coals.</p>

18205,IS,,ISO 10185:1993,Tobacco and tobacco products — Vocabulary,Tabac et produits du tabac — Vocabulaire,1993-06-09,1,"['65.160','01.040.65']",ISO/TC 126,9599,,[31190],"['en','fr']",27,"<p>Gives, in English and French, terms and definitions used in the production, processing and testing of tobacco and tobacco products, in section 1: from international standards on tobacco and tobacco products, in section 2: particularly related to oriental tobacco. Annex A gives a list, without definitions, of equivalent terms in English and French related to the following areas: leaf tobacco; physical measurements on cigarettes, filter plug rods and rag; chemical analysis of tobacco and tobacco products.

18210,IS,,ISO 10190:1992,Motor cycle chains — Characteristics and test methods,Chaînes pour motocycles — Caractéristiques et méthodes de contrôle,1992-05-21,1,['43.140'],ISO/TC 100,9599,,[40893],"['en','fr']",7,"<p>Specifies the dimensions and mechanical properties of roller and bush chains, in the range 6,35 mm to 19,05 mm pitch. These chains are suitable for internal and external drives. It covers dimensions, tolerances, length measurement, proof-testing, minimum tensile strengths and dynamic testing.</p>"

18211,IS,,ISO 10191:1993,Passenger car tyres — Verifying tyre capabilities — Laboratory test methods,Pneumatiques pour voitures particulières — Vérification de l'aptitude des pneumatiques — Méthodes d'essai en laboratoire,1993-05-27,1,['83.160.10'],ISO/TC 31/SC 3,9599,,[24588],"['en','fr']",9,

24588,IS,,ISO 10191:1995,Passenger car tyres — Verifying tyre capabilities — Laboratory test methods,Pneumatiques pour voitures particulières — Vérification de l'aptitude des pneumatiques — Méthodes d'essai en laboratoire,1995-12-14,2,['83.160.10'],ISO/TC 31/SC 3,9599,[18211],"[55324,31347]","['en','fr']",9,"<p>Contains test methods for verifying the capabilities of tyres for passenger cars. The tests are carried out in a laboratory under controlled conditions and are related to the strength test of the tread area with respect to braking energy, the endurance test with respect to full load and over long distances and the high speed test according to the speed category. Replaces the first edi

30086,IS,Amd,ISO 10191:1995/Amd 1:1998,Passenger car tyres — Verifying tyre capabilities — Laboratory test methods — Amendment 1,Pneumatiques pour voitures particulières — Vérification de l'aptitude des pneumatiques — Méthodes d'essai en laboratoire — Amendement 1,1998-09-03,2,['83.160.10'],ISO/TC 31/SC 3,9599,,"[55324,31347]","['en','fr']",1,

55324,IS,,ISO 10191:2010,Passenger car tyres — Verifying tyre capabilities — Laboratory test methods,Pneumatiques pour voitures particulières — Vérification de l'aptitude des pneumatiques — Méthodes d'essai en laboratoire,2010-02-24,3,['83.160.10'],ISO/TC 31/SC 3,9599,"[30086,24588]","[56892,78727]","['en','fr']",14,"<p>ISO 10191:2010 specifies test methods for verifying the capabilities of tyres for passenger cars. Of the test methods presented, it is possible that only some will be required depending on the type of tyre to be tested. The tests are carried out in a laboratory under controlled conditions.</p><p>ISO 10191:2010 includes a strength test for assessing the capability of the tyre

18223,IS,,ISO 10196:1990,Micrographics — Recommendations for the creation of original documents,Micrographie — Recommandations pour la création des documents originaux,1990-11-15,1,['37.080'],ISO/TC 171/SC 2,9599,,[26764],"['en','fr']",6,"<p>Provides guidance on the creation of original documents to facilitate their reproduction as microforms. Applies to documents in black on a clear background, made up of continuous lines. Does not apply to technical drawings for which requirements are given in ISO 5457 and ISO 6428.</p>"

3770,IS,,ISO 102:1976,Aircraft — Gravity filling orifices,Aéronefs — Orifices de remplissage par gravité,1976-04-01,1,['49.080'],ISO/TC 20/SC 10,9599,,[3771],"['en','fr']",1,

18234,IS,,ISO 10203:1992,Iron ores — Determination of calcium content — Flame atomic absorption spectrometric method,Minerais de fer — Dosage du calcium — Méthode par spectrométrie d'absorption atomique dans la flamme,1992-12-10,1,['73.060.10'],ISO/TC 102/SC 2,9599,[10674],[39729],"['en','fr']",9,"<p>The method is based on decomposition of the test portion by hydrochloric acid/nitric acid, evaporation, ignition of the residue and removal of silica, fusion with sodium carbonate and dissolution of the cooled melt in the filtrate, aspiration of the solution into the flame of an atomic absorption spectrometer, and comparison of the absorbance values obtained for calcium with those obtained from

39729,IS,,ISO 10203:2006,Iron ores — Determination of calcium — Flame atomic absorption spectrometric method,Minerais de fer — Dosage du calcium — Méthode par spectrométrie d'absorption atomique dans la flamme,2006-06-14,2,['73.060.10'],ISO/TC 102/SC 2,9599,[18234],"[43726,66465]",['en'],12,"<p>ISO 10203:2006 specifies a flame atomic absorption spectrometric method for the determination of the mass fraction of calcium in iron ores.</p><p>This method is applicable to mass fractions of calcium between 0,07 % and 4,5 % in natural iron ores, iron ore concentrates and agglomerates, including sinter products.</p>"

66465,IS,,ISO 10203:2015,Iron ores — Determination of calcium — Flame atomic absorption spectrometric method,Minerais de fer — Dosage du calcium — Méthode par spectrométrie d'absorption atomique dans la flamme,2015-06-19,3,['73.060.10'],ISO/TC 102/SC 2,9599,[39729],[69807],['en'],13,"<p>ISO 10203:2015 specifies a flame atomic absorption spectrometric method for the determination of the mass fraction of calcium in iron ores.</p><p>This method is applicable to mass fractions of calcium between 0,010 % and 8,00 % in natural iron ores, iron ore concentrates, and agglomerates, including sinter products.</p>"

18235,IS,,ISO 10204:1992,Iron ores — Determination of magnesium content — Flame atomic absorption spectrometric method,Minerais de fer — Dosage du magnésium — Méthode par spectrométrie d'absorption atomique dans la flamme,1992-12-10,1,['73.060.10'],ISO/TC 102/SC 2,9599,[10674],[39730],"['en','fr']",9,"<p>The method is based on decomposition of the test portion by hydrochloric acid/nitric acid, evaporation, ignition of the residue and removal of silica, fusion with sodium carbonate and dissolution of the cooled melt in the filtrate, aspiration of the solution into the flame of an atomic absorption spectrometer, and comparison of the absorbance values obtained for magnesium with those obtained

39730,IS,,ISO 10204:2006,Iron ores — Determination of magnesium — Flame atomic absorption spectrometric method,Minerais de fer — Dosage du magnésium — Méthode par spectrométrie d'absorption atomique dans la flamme,2006-06-14,2,['73.060.10'],ISO/TC 102/SC 2,9599,[18235],"[43727,66466]",['en'],12,"<p>ISO 10204:2006 specifies a flame atomic absorption spectrometric method for the determination of the mass fraction of magnesium in iron ores.</p><p>This method is applicable to mass fractions of magnesium between 0,25 % and 3,5 % in natural iron ores, iron ore concentrates and agglomerates, including sinter products.</p>"

66466,IS,,ISO 10204:2015,Iron ores — Determination of magnesium — Flame atomic absorption spectrometric method,Minerais de fer — Dosage du magnésium — Méthode par spectrométrie d'absorption atomique dans la flamme,2015-07-20,3,['73.060.10'],ISO/TC 102/SC 2,9599,[39730],[71883],['en'],13,"<p>ISO 10204:2015 specifies a flame atomic absorption spectrometric method for the determination of the mass fraction of magnesium in iron ores.</p><p>This method is applicable to mass fractions of magnesium between 0,010 % and 2,00 % in natural iron ores, iron ore concentrates, and agglomerates, including sinter products.</p>"

18241,IS,,ISO 10209-1:1992,Technical product documentation — Vocabulary — Part 1: Terms relating to technical drawings: general and types of drawings,Documentation technique de produit — Vocabulaire — Partie 1: Termes relatifs aux dessins techniques: généralités et types de dessins,1992-06-11,1,"['01.100.01','01.040.01']",ISO/TC 10/SC 1,9599,[5530],[51183],"['en','fr']",7,"<p>Includes 34 terms and definitions in English and French. Annex A gives the equivalent terms in the German, Italian and Swedish languages for information only.</p>"

18242,IS,,ISO 10209-2:1993,Technical product documentation — Vocabulary — Part 2: Terms relating to projection methods,Documentation technique de produit — Vocabulaire — Partie 2: Termes relatifs aux méthodes de projection,1993-09-23,1,"['01.100.01','01.040.01']",ISO/TC 10/SC 1,9599,,[51183],"['en','fr']",14,<p>Establishes and defines 60 terms used in technical product documentation covering all fields of application.</p>

51183,IS,,ISO 10209:2012,"Technical product documentation — Vocabulary — Terms relating to technical drawings, product definition and related documentation","Documentation technique de produits — Vocabulaire — Termes relatifs aux dessins techniques, à la définition de produits et à la documentation associée",2012-07-11,1,"['01.040.01','01.110']",ISO/TC 10,9599,"[23031,18241,18242]",[73872],"['de','en','fr']",110,"<p>ISO 10209:2012 establishes and defines terms used in technical product documentation relating to technical drawings, product definition and related documentation in all fields of application.</p><p>This vocabulary is based on all terms contained within ISO/TC 10 standards and oth

23031,IS,,ISO 10209-4:1999,Technical product documentation — Vocabulary — Part 4: Terms relating to construction documentation,Documentation technique de produit — Vocabulaire — Partie 4: Termes relatifs à la documentation des constructions,1999-08-05,1,"['01.100.30','01.040.01','01.110']",ISO/TC 10/SC 8,9599,,[51183],"['en','fr']",19,

2541,IS,,ISO 10211-1:1995,Thermal bridges in building construction — Heat flows and surface temperatures — Part 1: General calculation methods,Ponts thermiques dans le bâtiment — Flux de chaleur et températures superficielles — Partie 1: Méthodes générales de calcul,1995-08-17,1,['91.120.10'],ISO/TC 163/SC 2,9599,,[40967],"['en','fr']",54,<p>Sets out specifications on a 3-D geometrical model of a thermal bridge for the numerical calculation of heat flows in order to assess heat loss from a building and calculation of minimum surface temperatures in order to assess the risk of surface condensation.</p>

37034,IS,Cor,ISO 10211-1:1995/Cor 1:2002,Thermal bridges in building construction — Heat flows and surface temperatures — Part 1: General calculation methods — Technical Corrigendum 1,Ponts thermiques dans le bâtiment — Flux de chaleur et températures superficielles — Partie 1: Méthodes générales de calcul — Rectificatif technique 1,2002-06-13,1,['91.120.10'],ISO/TC 163/SC 2,9599,,[40967],"['en','fr']",7,

26410,IS,,ISO 10211-2:2001,Thermal bridges in building construction — Calculation of heat flows and surface temperatures — Part 2: Linear thermal bridges,Ponts thermiques dans les bâtiments — Calcul des flux thermiques et des températures superficielles — Partie 2: Ponts thermiques linéaires,2001-03-15,1,['91.120.10'],ISO/TC 163/SC 2,9599,,[40967],"['en','fr']",15,

40967,IS,,ISO 10211:2007,Thermal bridges in building construction — Heat flows and surface temperatures — Detailed calculations,Ponts thermiques dans les bâtiments — Flux thermiques et températures superficielles — Calculs détaillés,2007-12-05,1,['91.120.10'],ISO/TC 163/SC 2,9599,"[26410,37034,2541]",[65710],"['en','fr']",45,"<p>ISO 10211:2007 sets out the specifications for a three-dimensional and a two-dimensional geometrical model of a thermal bridge for the numerical calculation of:</p><ul><li> heat flows, in order to assess the overall heat loss from a building or part of it;</li><li> minimum surface temperatures, in order to assess the risk of surface condensation.</li></ul

18247,IS,,ISO 10214:1991,Photography — Processed photographic materials — Filing enclosures for storage,Photographie — Produits photographiques après traitement — Contenants pour classement destinés à l'archivage,1991-05-23,1,['37.040.20'],ISO/TC 42,9599,,[30862],"['en','fr']",8,"<p>Specifies the principal physical and chemical requirements for enclosures and containers particularly designed for storage processed films, plates, and papers. Applies to storage copies and does not include work copies. Annexes A and B are for information only.</p>"

18248,IS,Cor,ISO 10214:1991/Cor 1:1992,Photography — Processed photographic materials — Filing enclosures for storage — Technical Corrigendum 1,Photographie — Produits photographiques après traitement — Contenants pour classement destinés à l'archivage — Rectificatif technique 1,1992-01-23,1,['37.040.20'],ISO/TC 42,9599,,[30862],['en'],1,"<p>Modifies sub-clause 4.2: in the last paragraph, line 1, 'indirect' shall be replaced by 'direct'.</p>"

18249,IS,,ISO 10215:1992,Anodized aluminium and aluminium alloys — Visual determination of image clarity of anodic oxidation coatings — Chart scale method,Aluminium et alliages d'aluminium anodisés — Détermination de la netteté d'image sur couches anodiques — Méthode des échelles graduées,1992-10-29,1,['25.220.20'],ISO/TC 79/SC 2,9599,[7746],[51500],"['en','fr']",5,"<p>Image clarity is determined by visual estimation of three properties: image clearness, image distortion and haze of the coating layer. These properties are obtained by evaluating the image of a chart scale on the test samples. The test can only be applied to a flat surface.</p>"

51500,IS,,ISO 10215:2010,Anodizing of aluminium and its alloys — Visual determination of image clarity of anodic oxidation coatings — Chart scale method,Anodisation de l'aluminium et de ses alliages — Détermination de la netteté d'image sur couches anodiques — Méthode des échelles graduées,2010-08-02,2,['25.220.20'],ISO/TC 79/SC 2,9599,[18249],[72176],"['en','fr']",7,"<p>ISO 10215:2010 specifies a visual method for determining the image clarity of anodic oxidation coatings on aluminium and aluminium alloys, using a chart scale and a lightness scale, which are defined. The method can be applied only to flat surfaces that can reflect the image of the chart scale pattern.</p>"

18250,IS,,ISO 10216:1992,Anodized aluminium and aluminium alloys — Instrumental determination of image clarity of anodic oxidation coatings — Instrumental method,Aluminium et alliages d'aluminium anodisés — Détermination de la netteté d'image sur couches anodiques — Méthode instrumentale,1992-10-29,1,['25.220.20'],ISO/TC 79/SC 2,9599,[7746],[51501],"['en','fr']",5,"<p>The method is based on light coming through a first slit (light source), being converted to parallel light through a first lens (collimator), reflected at the surface of the test piece, focussed at a combed sliding shutter through a second lens (condensing lens). The signal measured by a photo-receiver behind the shutter is a m

51501,IS,,ISO 10216:2010,Anodizing of aluminium and its alloys — Instrumental determination of image clarity of anodic oxidation coatings — Instrumental method,Anodisation de l'aluminium et de ses alliages — Détermination de la netteté d'image sur couches anodiques — Méthode instrumentale,2010-03-15,2,['25.220.20'],ISO/TC 79/SC 2,9599,[18250],[70153],['en'],9,<p>ISO 10216:2010 specifies an instrumental method for determining the image clarity of anodic oxidation coatings on aluminium and aluminium alloys by measuring reflection from the surface with the help of a sliding combed shutter.</p><p>The test can only be applied to a flat surface which can reflect the image on the limited combed shu

59396,IS,Cor,ISO 10216:2010/Cor 1:2011,Anodizing of aluminium and its alloys — Instrumental determination of image clarity of anodic oxidation coatings — Instrumental method — Technical Corrigendum 1,Anodisation de l'aluminium et de ses alliages — Détermination de la netteté d'image sur couches anodiques — Méthode instrumentale — Rectificatif technique 1,2011-03-21,2,['25.220.20'],ISO/TC 79/SC 2,9599,,[70153],['en'],2,

70153,IS,,ISO 10216:2017,Anodizing of aluminium and its alloys — Instrumental determination of image clarity of anodic oxidation coatings — Instrumental method,Anodisation de l'aluminium et de ses alliages — Détermination de la netteté d'image sur couches anodiques — Méthode instrumentale,2017-10-09,3,['25.220.20'],ISO/TC 79/SC 2,9599,"[59396,51501]",[88295],['en'],9,<p>ISO 10216 specifies an instrumental method for determining the image clarity of anodic oxidation coatings on aluminium and its alloys by measuring reflection from the surface with the help of a sliding combed shutter.</p><p>The test can only be applied to a flat surface which can reflect the image onto the limited combed shut

36322,IS,,ISO 10218-1:2006,Robots for industrial environments — Safety requirements — Part 1: Robot,Robots pour environnements industriels — Exigences de sécurité — Partie 1: Robot,2006-05-23,1,['25.040.30'],ISO/TC 184,9599,"[23939,18252]",[51330],"['en','fr']",27,"<p>ISO 10218-1:2006 specifies requirements and guidelines for the inherent safe design, protective measures, and information for use of industrial robots. It describes basic hazards associated with robots, and provides requirements to eliminate or adequately reduce the risks associated with these hazards.</p><p>ISO 10218-1:2006 does not apply to non-industrial robots although the safety principles established in ISO 10218 may be u

46104,IS,Cor,ISO 10218-1:2006/Cor 1:2007,Robots for industrial environments — Safety requirements — Part 1: Robot — Technical Corrigendum 1,Robots pour environnements industriels — Exigences de sécurité — Partie 1: Robot — Rectificatif technique 1,2007-05-15,1,['25.040.30'],ISO/TC 184,9599,,[51330],"['en','fr']",1,

51330,IS,,ISO 10218-1:2011,Robots and robotic devices — Safety requirements for industrial robots — Part 1: Robots,Robots et dispositifs robotiques — Exigences de sécurité pour les robots industriels — Partie 1: Robots,2011-07-01,2,['25.040.30'],ISO/TC 299,9599,"[46104,36322]",[73933],"['en','fr']",43,"<p>ISO 10218-1:2011 specifies requirements and guidelines for the inherent safe design, protective measures and information for use of industrial robots. It describes basic hazards associated with robots and provides requirements to eliminate, or adequately reduce, the risks associated with these hazards.</p><p>ISO 10218-1:2011 does not address the robot as a complete machine. Noise emission i

18252,IS,,ISO 10218:1992,Manipulating industrial robots — Safety,Robots manipulateurs industriels — Sécurité,1992-01-23,1,['25.040.30'],ISO/TC 184,9599,,"[34403,23939,36322]","['en','fr']",10,"<p>Provides guidance on the safety considerations for the design, construction, programming, operation, use, repair and maintenance of robots.</p>"

23939,IS,Cor,ISO 10218:1992/Cor 1:1994,Manipulating industrial robots — Safety — Technical Corrigendum 1,Robots manipulateurs industriels — Sécurité — Rectificatif technique 1,1994-05-15,1,['25.040.30'],ISO/TC 184,9599,[18252],"[34403,36322]",['fr'],,

41571,IS,,ISO 10218-2:2011,Robots and robotic devices — Safety requirements for industrial robots — Part 2: Robot systems and integration,Robots et dispositifs robotiques — Exigences de sécurité pour les robots industriels — Partie 2: Systèmes robots et intégration,2011-07-01,1,['25.040.30'],ISO/TC 299,9599,,[73934],"['en','fr']",72,"<p>ISO 10218-2:2011 specifies safety requirements for the integration of industrial robots and industrial robot systems as defined in ISO 10218-1, and industrial robot cell(s). The integration includes the following:</p><ul><li> the design, manufacturing, installation, operation, maintenance and decommissioning of the industrial robot system or cell;</li><

5493,IS,,ISO 1022:1988,Aerospace — Gaseous oxygen replenishment connection for use in fluid systems (old type) — Dimensions (Inch series) (Not valid for new designs),Aéronautique et espace — Raccordement pour l'alimentation en oxygène gazeux dans les systèmes de fluide,1988-01-28,1,"['49.100','49.080']",ISO/TC 20/SC 10,9599,,[16190],"['en','fr']",3,"<p>Specifies the mating dimensions and access clearance. Is not applicable to new designs; for the latter, reference should be made to ISO 8775. The requirements apply to coupling mating dimensions, thread, plugging of orifice and access clearance.</p>"

18257,IS,,ISO 10223:1992,Textile machinery — Flat warp knitting machines — Numbering of guide bars,Matériel pour l'industrie textile — Machines à tricoter rectilignes à mailles jetées — Numérotage des barres à passettes,1992-06-11,1,['59.120.40'],ISO/TC 72/SC 3,9599,,[36238],"['en','fr']",3,<p>Numbering is in Arabic figures. Classification conforms to ISO 7839:1984 and the side designation to ISO 8640-1:1990.</p>

18262,IS,,ISO 10228:1991,Cross-country skis — Binding mounting area — Requirements for test screws,Skis de fond — Zone de montage de la fixation — Exigences pour des vis d'essai,1991-11-21,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[55818],"['en','fr']",3,"<p>Specifies the dimensions, mechanical properties and fastening characteristics of test screws used for testing the binding mounting area of cross-country skis.</p>"

5494,IS,,ISO 1023:1974,Aircraft — High pressure air charging valves,Aéronefs — Raccords pour l'alimentation en air à haute pression,1974-07-01,1,"['49.100','49.080']",ISO/TC 20/SC 10,9599,,[1081],"['en','fr']",2,<p>Includes the coupling dimensions and access clearance. The basic dimensions of the valve and the access clearance to be provided shall conform to the requirements of figure 1. The valves shall be provided at the coupling end with a srew thread conforming to the requirements of figure 2. The valves are given in tables.</p>

18267,IS,,ISO 10231:1992,Motorcycle tyres — Test methods for verifying tyre capabilities,Pneumatiques pour motocycles — Méthodes d'essai pour la vérification de l'aptitude des pneumatiques,1992-10-08,1,['83.160.10'],ISO/TC 31/SC 10,9599,,[25327],"['en','fr']",7,

25327,IS,,ISO 10231:1997,Motorcycle tyres — Test methods for verifying tyre capabilities,Pneumatiques pour motocycles — Méthodes d'essai pour la vérification de l'aptitude des pneumatiques,1997-11-27,2,['83.160.10'],ISO/TC 31/SC 10,9599,[18267],[37790],"['en','fr']",11,

30231,IS,Amd,ISO 10231:1997/Amd 1:1999,Motorcycle tyres — Test methods for verifying tyre capabilities — Amendment 1,Pneumatiques pour motocycles — Méthodes d'essai pour la vérification de l'aptitude des pneumatiques — Amendement 1,1999-11-04,2,['83.160.10'],ISO/TC 31/SC 10,9599,,[37790],"['en','fr']",1,

37790,IS,,ISO 10231:2003,Motorcycle tyres — Test methods for verifying tyre capabilities,Pneumatiques pour motocycles — Méthodes d'essai pour la vérification de l'aptitude des pneumatiques,2003-08-22,3,['83.160.10'],ISO/TC 31/SC 10,9599,"[25327,30231]",[80927],"['en','fr']",11,"<p>ISO 10231:2003 specifies test methods for verifying the capabilities of tyres for motorcycles, carried out in the laboratory under controlled conditions. The tests include a strength test for assessing the capability of the tyre structure with respect to breaking energy in the tread area, an endurance test for assessing the resistance of the tyre with respect to service at full load and moderate speed over long dis

61774,IS,Amd,ISO 10231:2003/Amd 1:2015,Motorcycle tyres — Test methods for verifying tyre capabilities — Amendment 1,Pneumatiques pour motocycles — Méthodes d'essai pour la vérification de l'aptitude des pneumatiques — Amendement 1,2015-09-27,3,['83.160.10'],ISO/TC 31/SC 10,9599,,[80927],"['en','fr']",1,

80927,IS,,ISO 10231:2022,Motorcycle tyres — Test methods for verifying tyre capabilities,Pneumatiques pour motocycles — Méthodes d'essai pour la vérification de l'aptitude des pneumatiques,2022-08-05,4,['83.160.10'],ISO/TC 31/SC 10,9599,"[61774,37790]",[87303],"['en','fr']",11,"<p>This document specifies test methods for verifying the capabilities of tyres for motorcycles. Of the test methods presented, only some can be required depending on the type of tyre to be tested.</p><p>The tests are carried out in the laboratory under controlled conditions. This document includes a strength test for assessing the capability of the tyre structure, with respect to breaking energy. A second test, the e

33318,IS,,ISO 10239:2000,Small craft — Liquefied petroleum gas (LPG) systems,Petits navires — Installations alimentées en gaz de pétrole liquéfiés (GPL),2000-08-24,1,['47.080'],ISO/TC 188,9599,,[41913],"['en','fr']",14,

35654,IS,Cor,ISO 10239:2000/Cor 1:2001,Small craft — Liquefied petroleum gas (LPG) systems — Technical Corrigendum 1,Petits navires — Installations alimentées en gaz de pétrole liquéfiés (GPL) — Rectificatif technique 1,2001-07-26,1,['47.080'],ISO/TC 188,9599,,[41913],"['en','fr']",1,

41913,IS,,ISO 10239:2008,Small craft — Liquefied petroleum gas (LPG) systems,Petits navires — Installations alimentées en gaz de pétrole liquéfiés (GPL),2008-01-31,2,['47.080'],ISO/TC 188,9599,"[35654,33318]",[60148],"['en','fr','ru']",14,"<p>ISO 10239:2008 covers permanently installed liquefied petroleum gas (LPG) systems and LPG burning appliances on small craft of hull length up to 24 m, except for systems used on LPG-fuelled propulsion engines or LPG-driven generators.</p><p>ISO 10239:2008 does not cover appliances with directly attached gas cylinders, such as portable self-contained camping stoves and portable gas lamps.</p>"

60148,IS,,ISO 10239:2014,Small craft — Liquefied petroleum gas (LPG) systems,Petits navires — Installations alimentées en gaz de pétrole liquéfiés (GPL),2014-11-28,3,['47.080'],ISO/TC 188,9599,[41913],[81921],"['en','fr']",17,"<p>ISO 10239:2014 covers the installation of permanently installed liquefied petroleum gas LPG systems and LPG burning appliances on small craft of up to 24 m length of hull.</p><p>It does not cover devices used for LPG-fuelled propulsion engines or LPG-driven generators.</p><p>It covers cooking appliances with internal LPG cartridges, with a capacity of 225 g or less (See Annex D).</p><p>It covers storage of all LPG cylinders but is not intended to regulate the techni

5496,IS,,ISO 1024:1989,"Metallic materials — Hardness test — Rockwell superficial test (scales 15N, 30N, 45N, 15T, 30T and 45T)","Matériaux métalliques — Essai de dureté — Essai superficiel Rockwell (échelles 15N, 30N, 45N, 15T, 30T et 45T)",1989-10-19,1,['77.040.10'],ISO/TC 164/SC 3,9599,[7680],[26047],"['en','fr']",6,

18277,IS,,ISO 10240:1995,Small craft — Owner's manual,Navires de plaisance — Manuel du propriétaire,1995-08-17,1,['47.080'],ISO/TC 188,9599,,[33291],"['en','fr']",10,"<p>Gives a guidance to prepare an owner's manual, applicable to small crafts of up to 24 m length.</p>"

33291,IS,,ISO 10240:2004,Small craft — Owner's manual,Petits navires — Manuel du propriétaire,2004-09-22,2,['47.080'],ISO/TC 188,9599,[18277],[74205],"['en','fr']",13,<p>ISO 10240:2004 specifies the information that shall be included in the owner's manual of small craft of hull length up to 24 m.</p>

64507,IS,Amd,ISO 10240:2004/Amd 1:2015,Small craft — Owner's manual — Amendment 1,Petits navires — Manuel du propriétaire — Amendement 1,2015-05-04,2,['47.080'],ISO/TC 188,9599,,[74205],"['en','fr']",1,

74205,IS,,ISO 10240:2019,Small craft — Owner's manual,Petits navires — Manuel du propriétaire,2019-12-20,3,['47.080'],ISO/TC 188,9599,"[64507,33291]",[82384],"['en','fr']",16,<p>This document specifies requirements and information for inclusion in the owner's manual of small craft to enable the owner/operator to use the craft safely.</p>

18278,IS,,ISO 10241:1992,International terminology standards — Preparation and layout,Normes terminologiques internationales — Élaboration et présentation,1992-12-30,1,"['01.120','01.020']",ISO/TC 37/SC 2,9599,"[5330,5693]","[40362,40363]","['en','fr']",21,"<p>Establishes rules for the preparation: preliminary work (needs analysis, target group, subject delimitation, sources, number of concepts, choice of languages, schedule) and working procedure (collecting and recording terminological data, establishing the term list, concept fields and concept systems, formulating definitions, coining and selecting terms), as well as for the terminography (structuring of entries, order of entries, indexe

18279,IS,,ISO 10242-1:1991,Tools for pressing — Punch holder shanks — Part 1: Types A and B,Outillage de presse — Nez de presse — Partie 1: Types A et B,1991-11-14,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[26700],"['en','fr']",3,

26700,IS,,ISO 10242-1:1998,Tools for pressing — Punch holder shanks — Part 1: Type A,Outillage de presse — Nez de presse — Partie 1: Type A,1998-07-23,2,['25.120.10'],ISO/TC 29/SC 8,9599,[18279],[57879],"['en','fr']",3,

18280,IS,,ISO 10242-2:1991,Tools for pressing — Punch holder shanks — Part 2: Type C,Outillage de presse — Nez de presse — Partie 2: Type C,1991-11-14,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[45058],"['en','fr']",3,"<p>Specifies the dimensions and tolerances which are necessary to ensure interchangeability. Gives guidance on the materials, and states the hardness and designation of shanks. Annex A is for information only.</p>"

18281,IS,,ISO 10242-3:1991,Tools for pressing — Punch holder shanks — Part 3: Type D,Outillage de presse — Nez de presse — Partie 3: Type D,1991-11-14,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[45059],"['en','fr']",3,"<p>Specifies the dimensions and tolerances which are necessary to ensure interchangeability. Gives guidance on the materials, and states the hardness and designation of shanks. Annex A is for information only.</p>"

18282,IS,,ISO 10243:1991,Tools for pressing — Compression springs with rectangular section — Housing dimensions and colour coding,Outillage de presse — Ressorts de compression à section rectangulaire — Dimensions d'encombrement et code de couleur,1991-08-29,1,"['01.070','25.120.10']",ISO/TC 29/SC 8,9599,,[50759],"['en','fr']",17,"<p>Lays down the technical specifications for springs made from rectangular wires. The springs are classified into the spring rates: light, medium, strong and extra strong. Each marked by a colour code.</p>"

50759,IS,,ISO 10243:2010,Tools for pressing — Compression springs with rectangular section — Housing dimensions and colour coding,Outillage de presse — Ressorts de compression à section rectangulaire — Dimensions d'encombrement et code de couleur,2010-01-22,2,"['01.070','25.120.10']",ISO/TC 29/SC 8,9599,[18282],"[75679,68889]","['en','fr']",18,"<p>ISO 10243:2010 establishes the technical specifications for compression springs made from rectangular wires.</p><p>It is applicable to springs which are set. It does not attempt to specify the quality of the springs themselves, nor all of their dimensions (e.g. cross-section), their material or their length of life.</p><p>The springs are classified

58104,IS,Amd,ISO 10243:2010/Amd 1:2011,Tools for pressing — Compression springs with rectangular section — Housing dimensions and colour coding — Amendment 1,Outillage de presse — Ressorts de compression à section rectangulaire — Dimensions d'encombrement et code de couleur — Amendement 1,2011-11-18,2,"['01.070','25.120.10']",ISO/TC 29/SC 8,9599,,"[75679,68889]","['en','fr']",1,

18284,IS,,ISO 10245-1:1994,Cranes — Limiting and indicating devices — Part 1: General,Appareils de levage à charge suspendue — Limiteurs et indicateurs — Partie 1: Généralités,1994-08-04,1,['53.020.20'],ISO/TC 96/SC 8,9599,,[43577],"['en','fr']",3,"<p>Specifies general requirements for limiting and indicating devices for lifting appliances that are applicable to loads and motions, performance and environment. These devices restrict operation and/or provide the driver or other persons with operational information.</p>"

43577,IS,,ISO 10245-1:2008,Cranes — Limiting and indicating devices — Part 1: General,Appareils de levage à charge suspendue — Limiteurs et indicateurs — Partie 1: Généralités,2008-01-07,2,['53.020.20'],ISO/TC 96/SC 8,9599,[18284],[76575],"['en','fr','ru']",9,"<p>ISO 10245-1:2008 specifies general requirements for limiting and indicating devices for cranes that are applicable to loads and motions, performance and environment. These devices restrict operation and/or provide the operator or other persons with operational information.</p>"

18285,IS,,ISO 10245-2:1994,Cranes — Limiting and indicating devices — Part 2: Mobile cranes,Appareils de levage à charge suspendue — Limiteurs et indicateurs — Partie 2: Grues mobiles,1994-06-16,1,['53.020.20'],ISO/TC 96/SC 6,9599,,[60618],"['en','fr']",5,"<p>Specifies the requirements for devices which limit and/or indicate the loads, motions, performance and environment of mobile cranes. The general requirements for limiting and indicating devices for cranes are given in ISO 10245-1. Applies to all mobile cranes as defined in 4306-2. Some basic machine types within this scope are convertible for use in excavating work and other applications not considered to be lifting service. The require

2662,IS,,ISO 10245-3:1999,Cranes — Limiting and indicating devices — Part 3: Tower cranes,Appareils de levage à charge suspendue — Limiteurs et indicateurs — Partie 3: Grues à tour,1999-09-30,1,['53.020.20'],ISO/TC 96/SC 7,9599,,[41283],"['en','fr']",3,

41283,IS,,ISO 10245-3:2008,Cranes — Limiting and indicating devices — Part 3: Tower cranes,Appareils de levage à charge suspendue — Limiteurs et indicateurs — Partie 3: Grues à tour,2008-01-07,2,['53.020.20'],ISO/TC 96/SC 7,9599,[2662],[71573],"['en','fr','ru']",8,"<p>ISO 10245-3:2008 gives requirements specific to tower cranes for limiting and indicating devices. It is applicable to tower cranes as defined in ISO 4306‑3. It is not applicable to end stops such as buffers used to stop trolleying, travelling or derricking movements, nor to erection, dismantling operations or the changing of a crane's configuration. </p>"

18286,IS,,ISO 10245-5:1995,Cranes — Limiting and indicating devices — Part 5: Overhead travelling and portal bridge cranes,Appareils de levage à charge suspendue — Dispositifs limiteurs et indicateurs — Partie 5: Ponts roulants et ponts portiques,1995-12-14,1,['53.020.20'],ISO/TC 96/SC 9,9599,,[89339],['en'],3,"<p>Specifies the requirements for limiting and indicating devices of bridges and gantry cranes for loads, motions, performance and environment. General requirements for limiting and indicating devices for cranes are given in ISO 10245-1.</p>"

18290,IS,,ISO 10249:1996,Fluid fertilizers — Preliminary visual examination and preparation of samples for physical testing,Engrais liquides — Examen visuel préliminaire et préparation des échantillons pour essais physiques,1996-12-19,1,['65.080'],ISO/TC 134,9599,,[92715],"['en','fr']",5,<p>Specifies a procedure for preliminary examination of a single sample as received and a procedure for preparing a test sample by blending and reduction of a series of samples representative of a consignment of fluid fertilizer.</p>

5497,IS,,ISO 1025:1981,Textile machinery and accessories — Sectional beams for warp knitting machines — Terminology and main dimensions,Matériel pour l'industrie textile — Ensouples sectionnelles pour métiers à mailles jetées — Terminologie et dimensions principales,1981-10-01,1,"['59.120.40','01.040.59']",ISO/TC 72,9599,,[15171],"['en','fr']",2,

18291,IS,,ISO 10250:1994,Metallic materials — Hardness testing — Tables of Knoop hardness values for use in tests made on flat surfaces,Matériaux métalliques — Essai de dureté — Tableaux des valeurs de dureté Knoop pour utilisation dans les essais effectués sur surfaces planes,1994-09-08,1,['77.040.10'],ISO/TC 164/SC 3,9599,,[37738],"['en','fr']",21,<p>Gives a table for calculation of Knoop hardness values for use in tests carried out in accordance with ISO 4545.</p>

18292,IS,,ISO 10251:1997,"Copper, lead and zinc sulfide concentrates — Determination of mass loss of bulk material on drying","Concentrés sulfurés de cuivre, de plomb et de zinc — Détermination de la perte de masse au séchage du matériau en vrac",1997-12-18,1,['73.060.99'],ISO/TC 183,9599,,[41316],['en'],13,

18294,IS,,ISO 10253:1995,Water quality — Marine algal growth inhibition test with Skeletonema costatum and Phaeodactylum tricornutum,Qualité de l'eau — Essai d'inhibition de la croissance des algues marines avec Skeletonema costatum et Phaeodactylum tricornutum,1995-09-28,1,['13.060.70'],ISO/TC 147/SC 5,9599,,[34811],"['en','fr']",8,<p>Specifies a method for the determination of the toxicity of chemical compounds on the growth of marine algae. The method can be used for testing substances which are readily soluble in water. With minor changes also applicable for the determination of the inhibitory effects of effluents.</p>

34811,IS,,ISO 10253:2006,Water quality — Marine algal growth inhibition test with Skeletonema costatum and Phaeodactylum tricornutum,Qualité de l'eau — Essai d'inhibition de la croissance des algues marines avec Skeletonema costatum et Phaeodactylum tricornutum,2006-04-10,2,['13.060.70'],ISO/TC 147/SC 5,9599,[18294],[66657],"['en','fr']",12,<p>ISO 10253:2006 specifies a method for the determination of the inhibition of growth of the unicellular marine algae <i>Skeletonema costatum</i> and<i> Phaeodactylum tricornutum</i> by substances and mixtures contained in sea water.The method can be used for testing substances that are readily soluble in water and are not significantly degraded or elimi

66657,IS,,ISO 10253:2016,Water quality — Marine algal growth inhibition test with Skeletonema sp. and Phaeodactylum tricornutum,Qualité de l'eau — Essai d'inhibition de la croissance des algues marines avec Skeletonema sp. et Phaeodactylum tricornutum,2016-11-04,3,['13.060.70'],ISO/TC 147/SC 5,9599,[34811],[85458],"['en','fr']",19,"<p>ISO 10253:2016 specifies a method for the determination of the inhibition of growth of the unicellular marine algae <i>Skeletonema</i> sp. and <i>Phaeodactylum tricornutum</i> by substances and mixtures contained in sea water or by environmental water samples (effluents, elutriates, etc.).</p><p>The method can be used for testing substances that are readily sol

18295,IS,,ISO 10254:1995,Air cargo and ground equipment — Vocabulary,Fret aérien et matériel au sol associé — Vocabulaire,1995-01-19,1,"['49.100','01.040.49','49.120']",ISO/TC 20/SC 9,9599,,[54747],"['en','fr']",19,<p>Defines 117 terms in English and French in the alphabetic order of the English versions. Alphabetic indexes in English and French are given the English index including all entries resulting from repositioning of the words in a term.</p>

54747,IS,,ISO 10254:2016,Air cargo and ground equipment — Vocabulary,Fret aérien et matériel au sol — Vocabulaire,2016-07-01,2,"['49.100','01.040.49','49.120']",ISO/TC 20/SC 9,9599,[18295],[84969],"['en','fr']",49,"<p>ISO 10254:2016 defines the terms relating to air cargo and aircraft ground equipment, as used in the other International Standards in these areas.</p><p>NOTE The term 'weight' is used throughout ISO 10254:2016 instead of the correct technical term 'mass', in order to conform to current commercial usage.</p><p>The terms and abridged definitions of ISO 10254:2016 are primarily intended to provide uniform understanding of the International Standards prepared by TC20/SC9.

52303,IS,,ISO 10256-1:2016,Protective equipment for use in ice hockey — Part 1: General requirements,Équipements de protection destinés à être utilisés en hockey sur glace — Partie 1: Exigences générales,2016-11-24,1,"['13.340.20','97.220.20']",ISO/TC 83/SC 5,9599,[28672],[81482],"['en','fr']",6,"<p>ISO 10256-1:2016 is part of ISO 10256 specifies general requirements for head, face, neck and body protectors (hereafter referred to as protectors) for use in ice hockey.</p><p>ISO 10256-1:2016 is intended only for protectors used for ice hockey. Requirements are given for the following:</p><p>a) terms and definitions;</p><p>b) innocuousness;</p><p>c) ergonomics;</p><p>d) test report;

18296,IS,,ISO 10256:1996,Protective helmets for ice hockey players,Casques protecteurs pour joueurs de hockey sur glace,1996-10-03,1,"['13.340.20','97.220.20']",ISO/TC 83/SC 5,9599,,[28672],"['en','fr']",18,

61495,IS,,ISO 10256-2:2016,Protective equipment for use in ice hockey — Part 2: Head protection for skaters,Équipements de protection destinés à être utilisés en hockey sur glace — Partie 2: Protections de tête pour les skateurs,2016-11-24,1,"['13.340.20','97.220.20']",ISO/TC 83/SC 5,9599,[28672],[81486],"['en','fr']",26,"<p>ISO 10256-2:2016 specifies performance requirements and test methods for head protectors for use in ice hockey and is intended to be read in conjunction with ISO 10256‑1.</p><p>Requirements and the corresponding test methods, where appropriate, are given for the following:</p><p>a) construction and protected area;</p><p>b) shock absorption;</p><p>c) penetration;

28672,IS,,ISO 10256:2003,Head and face protection for use in ice hockey,Protections de tête et de visage destinées à être utilisées en hockey sur glace,2003-10-10,2,"['13.340.20','97.220.20']",ISO/TC 83/SC 5,9599,"[18296,18297]","[74089,61495,61496,65010,52303,61497]","['en','fr']",48,"<p>ISO 10256:2003 specifies performance requirements and test methods for head and face protection for use in ice hockey.</p><p>Perfarmance requirements and test methods, where appropriate, are given for the following: construction; shock absorption; puck-impact resistance; penetration; retention-system properties; field of vision; marking and information.</p><p>The head and face protection is intended for use

61496,IS,,ISO 10256-3:2016,Protective equipment for use in ice hockey — Part 3: Face protectors for skaters,Équipements de protection destinés à être utilisés en hockey sur glace — Partie 3: Protections faciales pour les skateurs,2016-11-24,1,"['13.340.20','97.220.20']",ISO/TC 83/SC 5,9599,[28672],[81487],"['en','fr']",28,"<p>ISO 10256-3:2016 specifies performance requirements and test methods for face protectors (including visors) for use in ice hockey and is intended to be used in conjunction with ISO 10256‑1.</p><p>Requirements and the corresponding test methods, where appropriate, are given for the following:</p><p>a) construction and area of coverage;</p><p>b) resistance to puck i

61497,IS,,ISO 10256-4:2016,Protective equipment for use in ice hockey — Part 4: Head and face protection for goalkeepers,Équipements de protection destinés à être utilisés en hockey sur glace — Partie 4: Protections de tête et de visage pour les gardiens de but,2016-11-24,1,"['13.340.20','97.220.20']",ISO/TC 83/SC 5,9599,[28672],[81488],"['en','fr']",10,"<p>ISO 10256-4:2016 covers performance requirements for head and face protectors to be used by ice hockey goalkeepers. It is intended to be read in conjunction with ISO 10256‑1, ISO 10256‑2 and ISO 10256‑3.</p><p>Performance requirements are established, where appropriate for the following:</p><p>a) materials, assembly, and design;</p><p>

65010,IS,,ISO 10256-5:2017,Protective equipment for use in ice hockey — Part 5: Neck laceration protectors for ice hockey players,Équipements de protection destinés à être utilisés en hockey sur glace — Partie 5: Protège-cous contre les lacérations pour joueurs de hockey sur glace,2017-03-20,1,"['13.340.20','97.220.20']",ISO/TC 83/SC 5,9599,[28672],[84204],['en'],22,"<p>ISO 10256-5:2017 specifies performance requirements and test methods for neck laceration protectors used in ice hockey. Neck laceration protectors are needed to reduce the risk of direct laceration to the neck caused by contact of a hockey skate blade.</p><p>The tests required to ensure that a neck laceration protector confor

18297,IS,,ISO 10257:1996,Face protectors and visors for ice hockey players,Protecteurs de visage et visières pour joueurs de hockey sur glace,1996-10-03,1,"['13.340.20','97.220.20']",ISO/TC 83/SC 5,9599,,[28672],['en'],28,

18298,IS,,ISO 10258:1994,Copper sulfide concentrates — Determination of copper content — Titrimetric methods,Concentrés de sulfure de cuivre — Dosage du cuivre — Méthodes titrimétriques,1994-06-16,1,['73.060.99'],ISO/TC 183,9599,,[63362],"['en','fr']",17,"<p>Specifies two titrimetric methods for the determination of the copper content of copper sulfide concentrates in the range 15 % (m/m) to 50 % (m/m), titrating free iodine isolated by reaction between iodide ions and copper(II) ions with sodium thiosulfate using soluble starch as the indicator after separation (method 1) or without separation (method 2) of copper from interfering elements.</p>"

63362,IS,,ISO 10258:2015,Copper sulfide concentrates — Determination of copper content — Titrimetric methods,Concentrés de sulfure de cuivre — Dosage du cuivre — Méthodes titrimétriques,2015-06-15,2,['73.060.99'],ISO/TC 183,9599,[18298],[74664],['en'],20,"<p>ISO 10258:2015 specifies two titrimetric methods for the determination of the copper content of copper sulfide concentrates in the range 15 % (m/m) to 50 % (m/m), using sodium thiosulfate after separation (method 1) or without separation (method 2) of copper from interfering elements.</p>"

18301,IS,,ISO 10261:1994,Earth-moving machinery — Product identification numbering system,Engins de terrassement — Système de numérotation pour l'identification des produits,1994-07-28,1,['53.100'],ISO/TC 127/SC 3,9599,,[32978],"['en','fr']",4,"<p>Specifies the requirements, location, and structure of uniform identification marking of earth-moving machinery, as defined in ISO 6165, to facilitate identification. Does not cover the label/plate for identification of e.g. the operator's station, components or attachments.</p>"

32978,IS,,ISO 10261:2002,Earth-moving machinery — Product identification numbering system,Engins de terrassement — Système de numérotation pour l'identification des produits,2002-07-04,2,['53.100'],ISO/TC 127/SC 3,9599,[18301],"[54968,82369]","['en','fr']",8,"<p>This International Standard specifies the requirements, content, structure and location of a product identification numbering system for earth-moving machinery as defined in ISO 6165. It is not applicable to the identification of components or attachments.</p>"

66111,IS,Amd,ISO 10261:2002/Amd 1:2015,Earth-moving machinery — Product identification numbering system — Amendment 1,Engins de terrassement — Système de numérotation pour l'identification des produits — Amendement 1,2015-11-13,2,['53.100'],ISO/TC 127/SC 1,9599,,[82369],"['en','fr']",1,

18303,IS,,ISO 10263-1:1994,Earth-moving machinery — Operator enclosure environment — Part 1: General and definitions,Engins de terrassement — Ambiance dans l'enceinte de l'opérateur — Partie 1: Généralités et définitions,1994-12-15,1,['53.100'],ISO/TC 127/SC 2,9599,,[42453],"['en','fr']",2,<p>Specifies test methods and criteria for the evaluation of the operator enclosure environment in earth-moving machinery as defined in ISO 6165.</p>

21126,IS,,ISO 10263-2:1994,Earth-moving machinery — Operator enclosure environment — Part 2: Air filter test,Engins de terrassement — Ambiance dans l'enceinte de l'opérateur — Partie 2: Essai de l'élément du filtre à air,1994-12-15,1,['53.100'],ISO/TC 127/SC 2,9599,,[42454],"['en','fr']",6,<p>Specifies a uniform test method to determine performance levels of operator enclosure panel-type air filters used to filter the air entering an earth-moving machine operator enclosure with a powered fresh air system.</p>

21127,IS,,ISO 10263-3:1994,Earth-moving machinery — Operator enclosure environment — Part 3: Operator enclosure pressurization test method,Engins de terrassement — Ambiance dans l'enceinte de l'opérateur — Partie 3: Méthode d'essai du système de pressurisation de l'enceinte de l'opérateur,1994-12-15,1,['53.100'],ISO/TC 127/SC 2,9599,,[42455],"['en','fr']",3,<p>Specifies a test method which provides uniform measurement of the pressurization inside an operator enclosure of an earth-moving machine fitted with a device to pressurize the enclosure.</p>

21128,IS,,ISO 10263-4:1994,"Earth-moving machinery — Operator enclosure environment — Part 4: Operator enclosure ventilation, heating and/or air-conditioning test method","Engins de terrassement — Ambiance dans l'enceinte de l'opérateur — Partie 4: Méthode d'essai des systèmes de ventilation, de chauffage et/ou de conditionnement d'air de l'enceinte de l'opérateur",1994-12-15,1,['53.100'],ISO/TC 127/SC 2,9599,,[42456],"['en','fr']",7,"<p>Specifies a test method which provides uniform measurement of the temperature and humidity inside an operator enclosure of an earth-moving machine equipped with devices for air-conditioning, heating and/or ventilation.</p>"

21129,IS,,ISO 10263-5:1994,Earth-moving machinery — Operator enclosure environment — Part 5: Windscreen defrosting system test method,Engins de terrassement — Ambiance dans l'enceinte de l'opérateur — Partie 5: Méthode d'essai du système de dégivrage du pare-brise,1994-12-15,1,['53.100'],ISO/TC 127/SC 2,9599,,[42457],"['en','fr']",7,"<p>Specifies a test method to determine the performance of windscreen defrosting systems of earth-moving machinery, fitted with an operator enclosure and a device for defrosting the windscreen.</p>"

24608,IS,,ISO 10263-6:1994,Earth-moving machinery — Operator enclosure environment — Part 6: Determination of effect of solar heating on operator enclosure,Engins de terrassement — Ambiance dans l'enceinte de l'opérateur — Partie 6: Détermination de l'effet du rayonnement solaire sur l'enceinte de l'opérateur,1994-12-15,1,['53.100'],ISO/TC 127/SC 2,9599,,[42458],"['en','fr']",2,<p>Specifies a test method for applying a simulated solar load in the laboratory and determining the radiant heat energy by artificial light source or a natural solar load which affects an operator enclosure of an earth-moving machine. Allows the radiant energy affecting an operator enclosure to be determined during t

18305,IS,,ISO 10265:1998,Earth-moving machinery — Crawler machines — Performance requirements and test procedures for braking systems,Engins de terrassement — Engins à chenilles — Exigences de performance et procédures d'essai des dispositifs de freinage,1998-04-23,1,['53.100'],ISO/TC 127/SC 1,9599,,[39809],"['en','fr']",6,

5499,IS,,ISO 1027:1983,Radiographic image quality indicators for non-destructive testing — Principles and identification,Indicateurs de qualité d'image radiographique pour les essais non destructifs — Principes et identification,1983-10-01,1,['19.100'],ISO/TC 135/SC 5,9599,,"[39001,39000]","['en','fr']",3,"<p>The detection of an imperfection in a product subjected to X or gamma radiography depends on the quality of the resultant radiograph. This quality should be checked with an image quality indicator. This International Standard is intended for general application on all metals. However, for particular materials (for example, aluminium and its alloys) complementary International Standards