Withdrawn and superseded ISO standards — page 229 of 246

14158,TR,,ISO/TR 7423:1982,Hermetically sealed metal containers for food and drinks — Food cans for fish and other fishery products — Sections for non-round cans,Récipients métalliques étanches pour denrées alimentaires et boissons — Boîtes à conserves alimentaires pour poissons et autres produits de la pêche — Sections des boîtes non rondes,1982-01-01,1,['55.120'],ISO/TC 52,9599,,[8073],"['en','fr']",3,

14175,TR,,ISO/TR 7439:1981,Mechanical contraceptives — Intra-uterine devices,Contraceptifs mécaniques — Dispositifs intra-utérins,1981-10-01,1,['11.200'],ISO/TC 157,9599,,[26775],"['en','fr']",4,"<p>Describes basic requirements for these devices, associated insertion instruments, and for packaging, labelling and storage of such devices. The more important performance criteria have to be assessed by clinical experience and consequently remain outside the scope of the Technical Report.</p>"

14207,TR,,ISO/TR 7470:1978,Valve outlets for gas cylinders — List of standard provisions or those in use,Sorties de robinets des bouteilles à gaz — Inventaire des dispositions normalisées ou utilisées,1978-08-01,1,['23.020.35'],ISO/TC 58/SC 2,9599,,[14208],"['en','fr']",9,

14208,TR,,ISO/TR 7470:1988,Valve outlets for gas cylinders — List of provisions which are either standardized or in use,Sorties de robinets des bouteilles à gaz — Inventaire des dispositions normalisées ou utilisées,1988-12-15,2,['23.020.35'],ISO/TC 58/SC 2,9599,[14207],[69940],"['en','fr']",12,"<p>Specifies details for types of threads and thread sizes. Tabulates nominal diameters from 9,73 mm up to and including 30 mm together with the corresponding pitches and designations, refers to the national standards of concern (table 1). Table 2 contains valve outlets for toxic gases; valve outlets for flammable gases are given in table 3. Table 4 gives valve outlets for oxidizing gases, and table

14209,TR,,ISO/TR 7471:1981,Polypropylene (PP) pipes and fittings — Chemical resistance with respect to fluids,Tubes et raccords en polypropylène (PP) — Résistance chimique vis-à-vis des fluides,1981-06-01,1,"['23.040.45','23.040.20']",ISO/TC 138,9599,,[18415],['en'],12,

14210,TR,,ISO/TR 7472:1981,Low density polyethylene pipes and fittings — Chemical resistance with respect to fluids,Tubes et raccords en polyéthylène basse densité — Résistance chimique vis-à-vis des fluides,1981-06-01,1,"['23.040.45','23.040.20']",ISO/TC 138,9599,,[18415],"['en','fr']",10,

14211,TR,,ISO/TR 7473:1981,Unplasticized polyvinyl chloride pipes and fittings — Chemical resistance with respect to fluids,Tubes et raccords en polychlorure de vinyle non plastifié — Résistance chimique vis-à-vis des fluides,1981-06-01,1,"['23.040.45','23.040.20']",ISO/TC 138,9599,,[18415],['en'],10,

14212,TR,,ISO/TR 7474:1981,High density polyethylene pipes and fittings — Chemical resistance with respect to fluids to be conveyed,Tubes et raccords en polyéthylène haute densité — Résistance chimique vis-à-vis des fluides,1981-06-01,1,"['23.040.45','23.040.20']",ISO/TC 138,9599,,[18415],"['en','fr']",10,

14215,TR,,ISO/TR 7477:1985,Data communication — Arrangements for DTE to DTE physical connection using V.24 and X.24 interchange circuits,Transmission des données — Arrangements pour la connexion physique ETTD à ETTD utilisant des circuits de jonction V.24 et X.24,1985-10-03,1,['35.100.10'],ISO/IEC JTC 1/SC 6,9599,,[26137],"['en','fr']",8,"<p>Describes various arrangements for interconnection of Data Terminal Equipment (DTE), without intermediate Data Circuit-terminating Equipment, concerning electrical, mechanical, and functional characteristics. Applies to DTEs with interface circuits standardized in CCITT Recommendation V.24 for data transmission over telephone networks or with interface c

24191,TR,,ISO/TR 7507-6:1997,"Petroleum and liquid petroleum products — Calibration of vertical cylindrical tanks — Part 6: Recommendations for monitoring, checking and verification of tank calibration and capacity table","Pétrole et produits pétroliers liquides — Jaugeage des réservoirs cylindriques verticaux — Partie 6: Recommandations relatives à la surveillance, au contrôle et à la vérification du jaugeage des réservoirs et des tables de jaugeage",1997-10-23,1,['75.180.30'],ISO/TC 28/SC 2,9599,,[37004],"['en','fr']",8,

14384,TR,,ISO/TR 7596:1982,Socketing procedures for wire ropes — Resin socketing,Procédés de terminaison des câbles métalliques — Manchonnage à l'aide de résine,1982-12-01,1,['77.140.65'],ISO/TC 105,9599,,"[35961,38408]","['en','fr']",6,"<p>Provides guidance on recommended practices for the resin socketing. When socketing ropes which have wire tensile grades greater than 1 960 MPa, special precautions may be necessary and the rope supplier should be consulted. Rope terminations made by ISO/TR 7596 may be used for determining the breaking load of wire ropes in accordance with ISO 3108.</p>"

14412,TR,,ISO/TR 7620:1986,Rubber materials — Chemical resistance,Matériaux en caoutchouc — Résistance chimique,1986-11-06,1,['83.060'],ISO/TC 45/SC 4,9599,,"[37026,20156]","['en','fr']",22,"<p>Intended as a guide to the behaviour of this material in contact with chemicals as aggressive gases and fluids, e.g. acids, alkalies, solvents, etc. This information is based on practical experience of manufacturers and users and summarized in tables. Without prior knowledge or experience of application, table-based selections should be confirmed by tests, where attention should be paid to the possibility of rubber contaminating the liquid or gas. Annex with references and tables.</p>"

14435,TR,,ISO/TR 7628-2:1986,Road vehicles — Thermoplastics tubing for use in air braking systems — Part 2: Installation on the vehicle and test methods,Véhicules routiers — Tuyauteries thermoplastiques pour freinage pneumatique — Partie 2: Conditions de montage sur le véhicule et méthodes d'essai,1986-08-28,1,"['43.040.40','83.140.30']",ISO/TC 22,9599,,[14436],"['en','fr']",10,

14445,TR,,ISO/TR 7637-0:1984,Road vehicles — Electrical interference by conduction and coupling — Part 0: General and definitions,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 0: Généralités et définitions,1984-06-01,1,"['43.040.10','01.040.43']",ISO/TC 22,9599,,[14446],['en'],4,

14447,TR,,ISO/TR 7637-1:1984,Road vehicles — Electrical interference by conduction and coupling — Part 1: Vehicles with nominal 12 V supply voltage — Electrical transient conduction along supply lines only,Véhicules routiers — Perturbations électriques par conduction et par couplage — Partie 1: Véhicules à tension nominale de 12 V — Transmission des perturbations électriques par conduction uniquement le long des lignes d'alimentation,1984-06-01,1,['43.040.10'],ISO/TC 22,9599,,[14448],['en'],14,

14484,TR,,ISO/TR 7664:1984,"Rubber, raw solid natural and synthetic — General guidance on storage","Caoutchouc brut, solide, naturel et synthétique — Guide pour le stockage",1984-07-01,1,['83.040.10'],ISO/TC 45/SC 3,9599,,[31521],"['en','fr']",2,

14489,TR,,ISO/TR 7670:1982,Hermetically sealed metal containers for food and drinks — Food cans for fish and other fishery products — Capacities of round and non-round cans and associated diameters of round cans,Récipients métalliques étanches pour denrées alimentaires et boissons — Boîtes à conserves alimentaires pour poissons et autres produits de la pêche — Capacités des boîtes rondes et non rondes et diamètres associés des boîtes rondes,1982-02-01,1,['55.120'],ISO/TC 52,9599,,[8073],['en'],4,

14528,TR,,ISO/TR 7705:1983,Basic rules for specifying impact strength in steel specifications,Règles fondamentales de spécification des caractéristiques de résilience dans les normes d'aciers,1983-06-01,1,['77.080.20'],ISO/TC 17,9599,,[14529],['en'],7,

14529,TR,,ISO/TR 7705:1991,Guidelines for specifying Charpy V-notch impact prescriptions in steel specifications,Directives pour la spécification des prescriptions d'énergie de rupture sur éprouvette Charpy à entaille en V dans les normes d'acier,1991-11-14,2,['77.080.20'],ISO/TC 17/SC 20,9599,[14528],[65584],"['en','fr']",14,"<p>Describes test methods, information to be gained from the test, and use of subsize test pieces. This second edition cancels and replaces the first edition (1983). Annex A forms an integral part of this Technical Report.</p>"

14533,TR,,ISO/TR 7708:1983,Air quality — Particle size fraction definitions for health-related sampling,Qualité de l'air — Définitions des fractions de tailles des particules pour l'échantillonnage lié aux problèmes de santé,1983-11-01,1,['13.040.01'],ISO/TC 146/SC 2,9599,,[14534],"['en','fr']",13,

14573,TR,,ISO/TR 7735:1982,Wrought aluminium and aluminium alloys — Sheet — Tolerances on shape and dimensions,Aluminium et alliages d'aluminium corroyés — Tôles — Tolérances sur forme et dimensions,1982-12-01,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[12679],['en'],8,

27999,TR,,ISO/TR 7775:1997,Securities — Scheme for message types,Valeurs mobilières — Types de messages,1997-05-29,1,['03.060'],ISO/TC 68,9599,"[19475,14646]","[28373,25775]",['en'],140,

14739,TR,,ISO/TR 7821:1982,"Tobacco — Preparation and constitution of identical samples from the same lot (Code of practice, for collaborative studies for evaluating methods of test)",Tabac — Préparation et constitution d'échantillons identiques à partir d'un même lot (Code pratique pour la conduite d'essais comparatifs portant sur la qualité des méthodes d'essai),1982-12-01,1,['65.160'],ISO/TC 126/SC 1,9599,,[37215],"['en','fr']",5,"<p>Provides a practical framework for operations of dividing a lot (not necessarily homogeneous) of tobacco or tobacco products into several similar samples intended for collaborative studies either within or between laboratories. Covers tobacco as a test medium

14770,TR,,ISO/TR 7849:1987,Acoustics — Estimation of airborne noise emitted by machinery using vibration measurement,Acoustique — Détermination du bruit aérien émis par les machines par mesurage des vibrations,1987-12-17,1,['17.140.20'],ISO/TC 43/SC 1,9599,,"[40538,40537]","['en','fr']",20,<p>Gives basic requirements for reproducible methods for determining the sound power emitted by machines. The method is especially applicable in cases where direct measurements are not possible because of high background noise. The methods are only applicable to noise which is emitted by vibrating surfaces of solid structures and not to noise generated aerodynamically.</p>

14804,TR,,ISO/TR 7871:1997,Cumulative sum charts — Guidance on quality control and data analysis using CUSUM techniques,Cartes des sommes cumulées — Lignes directrices pour le contrôle de la qualité et l'analyse des données utilisant les procédures CUSUM,1997-02-27,1,['03.120.30'],ISO/TC 69/SC 4,9599,,[40176],"['en','fr']",40,<p>Gives the principles of cusum charting and includes guidance on the preparation and interpretation of cusum charts using basic decision rules.</p>

15127,TR,,ISO/TR 8091:1983,Textiles — Twist factor related to the Tex System,Textiles — Facteur de torsion lié au système Tex,1983-02-01,1,['59.080.01'],ISO/TC 38/SC 23,9599,,[45520],"['en','fr']",4,"<p>Gives equations for the calculation of twist factors in SI units and conversion tables with which twist factors expressed in other unit systems can be transformed into SI units. Applicable to single twisted yarns, folded yarns and cabled yarns.</p>"

63537,TR,,ISO/TR 8124-8:2014,Safety of toys — Part 8: Age determination guidelines,Sécurité des jouets — Partie 8: Lignes directrices pour la détermination de l'âge,2014-08-19,1,['97.200.50'],ISO/TC 181,9599,,[68561],['en'],28,"<p>ISO/TR 8124-8:2014 provides guidelines for the determination of the lowest age at which children start playing with toys in specific toy sub-categories and is primarily directed to manufacturers and agencies that evaluate the compliance of toys with safety standards.</p><p>ISO/TR 8124-8:2014 can also be used as a reference to determine the appropriateness of toys by earliest age, for use by distributors, institutions, and organizations involved with child play, as

68561,TR,,ISO/TR 8124-8:2016,Safety of toys — Part 8: Age determination guidelines,Sécurité des jouets — Partie 8: Lignes directrices pour la détermination de l'âge,2016-02-08,2,['97.200.50'],ISO/TC 181,9599,[63537],[76980],"['en','fr']",28,"<p>ISO/TR 8124-8:2016 provides guidelines for the determination of the lowest age at which children start playing with toys in specific toy sub-categories and is primarily directed to manufacturers and agencies that evaluate the compliance of toys with safety standards.</p><p>This Technical Report can also be used as a reference to determine the appropriateness of toys by earliest age, for use by distributors, institutions, and organizations involved wit

72509,TR,,ISO/TR 8124-9:2018,"Safety of toys — Part 9: Safety aspects related to mechanical and physical properties — Comparison of ISO 8124-1, EN 71-1, and ASTM F963","Sécurité des jouets — Partie 9: Aspects de sécurité relatifs aux propriétés mécaniques et physiques — Comparaison des ISO 8124-1, EN 71-1 et ASTM F963",2018-06-07,1,['97.200.50'],ISO/TC 181,9599,,[73839],['en'],100,<p>This document consists of a comparison of the mechanical and physical requirements covered by the following toy safety standards:</p><p>a) ISO: ISO 8124‑1:2014;</p><p>b) Europe (CEN): EN 71‑1:2014;</p><p>c) USA: ASTM F963:2011.</p>

73839,TR,,ISO/TR 8124-9:2020,"Safety of toys — Part 9: Safety aspects related to mechanical and physical properties — Comparison of ISO 8124-1, EN 71-1 and ASTM F963","Sécurité des jouets — Partie 9: Aspects de sécurité relatifs aux propriétés mécaniques et physiques — Comparaison entre l'ISO 8124-1, l'EN 71-1 et l'ASTM F963",2020-03-31,2,['97.200.50'],ISO/TC 181,9599,[72509],[82011],['en'],124,<p>This document consists of a comparison of the mechanical and physical requirements covered by the following toy safety standards:</p><p>a) ISO: ISO 8124‑1:2018;</p><p>b) Europe (CEN): EN 71‑1:2014+A1:2018;</p><p>c) USA: ASTM F963:2017.</p>

15188,TR,,ISO/TR 8125:1984,Anodizing of aluminium and its alloys — Determination of colour and colour difference of coloured anodic coatings,Anodisation de l'aluminium et de ses alliages — Détermination de la couleur et de la différence de couleur des couches anodiques colorées,1984-02-01,1,['25.220.20'],ISO/TC 79/SC 2,9599,,[1537],"['en','fr']",33,"<p>This Technical Report consists of three sections describing the visual method, the instrumental method, and the relation between instrumental and visual methods. The instrumental method also applies to small colour differences between colour-anodized aluminium surfaces observable in daylight illumination. Annex A specifies methods other than v

15347,TR,,ISO/TR 8244:1988,Plastics — Phenolic resins — Basis for classification,Plastiques — Résines phénoliques — Définitions pour classification,1988-11-03,1,['83.080.10'],ISO/TC 61/SC 12,9599,,[28610],"['en','fr']",4,

15404,TR,,ISO/TR 8285:1990,Plain bearings — Evaluation of the tribological properties of polymer-based materials,Paliers lisses — Évaluation des propriétés tribologiques des matériaux à base de polymères,1990-02-08,1,['21.100.10'],ISO/TC 123/SC 2,9599,,[20994],"['en','fr']",9,

15472,TR,,ISO/TR 8330:1986,Rubber and plastics — Glossary of terms used by the hose industry,Caoutchouc et plastiques — Glossaire des termes utilisés dans l'industrie des tuyaux,1986-10-02,1,"['01.040.83','23.040.70']",ISO/TC 45/SC 1,9599,,[25522],['en'],4,

15481,TR,,ISO/TR 8338:1988,Crude petroleum oil — Transfer accountability — Method for estimation on ships of total quantity remaining on board (ROB),Pétrole brut — Prise en compte des quantités chargées — Méthode pour l'estimation des quantités restant à bord des navires (ROB),1988-12-15,1,['75.180.30'],ISO/TC 28/SC 2,9599,,[16103],"['en','fr']",15,

51800,TR,,ISO/TR 834-2:2009,Fire-resistance tests — Elements of building construction — Part 2: Guidance on measuring uniformity of furnace exposure on test samples,Essais de résistance au feu — Éléments de construction — Partie 2: Lignes directrices pour la mesure de l'uniformité de l'exposition au feu des échantillons pour essai,2009-06-23,1,['13.220.50'],ISO/TC 92/SC 2,9599,,[75137],['en'],14,"<p>ISO/TR 834-2:2009 establishes general principles for measuring the uniformity of furnace exposure of samples tested in accordance with the requirements of ISO 834-1. ISO/TR 834-2:2009 specifies the type and location of instrumentation used to measure the temperature, velocity and oxygen content n

21811,TR,,ISO/TR 834-3:1994,Fire-resistance tests — Elements of building construction — Part 3: Commentary on test method and test data application,Essais de résistance au feu — Éléments de construction — Partie 3: Commentaires sur les méthodes d'essais et application des données d'essais,1994-10-13,1,['13.220.50'],ISO/TC 92/SC 2,9599,,[53956],"['en','fr']",12,<p>Provides information as guidance on the use of the fire resistance test method and the application of the data obtained. Also identifies a number of areas where future editions may benefit by research: into phenomena associated with the performance of assemblies under test and their relationship with actual building construction and

53956,TR,,ISO/TR 834-3:2012,Fire-resistance tests — Elements of building construction — Part 3: Commentary on test method and guide to the application of the outputs from the fire-resistance test,Essais de résistance au feu — Éléments de construction — Partie 3: Commentaires sur les méthodes d'essais et guide pour l'application des résultats des essais de résistance au feu,2012-06-06,2,['13.220.50'],ISO/TC 92/SC 2,9599,[21811],[83943],['en'],25,"<p>ISO/TR 834-3:2012 provides background and guidance on the use and limitations of the fire resistance test method and the application of the data obtained. It is designed to be of assistance to code officials, fire safety engineers, designers of bu

15494,TR,,ISO/TR 8349:1986,Road vehicles — Measurement of road surface friction,Véhicules routiers — Mesure du coefficient d'adhérence,1986-10-30,1,['43.020'],ISO/TC 22,9599,,[25944],"['en','fr']",13,<p>Specifies a method of measuring the characteristic longitudinal and lateral friction force values with specified reference tyres. The method is suitable for a simplified evaluation of the friction properties of a test track surface. Annex A contains reference tyre specifications; the test equipment is given in annex B; annex C describes the measurement of ambient conditions.</p>

28929,TR,,ISO/TR 8363:1997,Measurement of liquid flow in open channels — General guidelines for selection of method,Mesure de débit des liquides dans les canaux découverts — Lignes directrices générales pour la sélection de la méthode,1997-09-04,1,['17.120.20'],ISO/TC 113/SC 1,9599,[15518],"[53942,62267]",['en'],7,

15656,TR,,ISO/TR 8461:1984,"Rubber, vulcanized — Classification — Rubber materials",Caoutchouc vulcanisé — Classification — Matériaux caoutchouc,1984-09-01,1,['83.060'],ISO/TC 45,9599,,[30866],"['en','fr']",46,

15732,TR,,ISO/TR 8509:1987,Information processing systems — Open Systems Interconnection — Service conventions,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Conventions de service,1987-09-03,1,['35.100.01'],ISO/IEC JTC 1,9599,,[18824],"['en','fr']",9,

15795,TR,,ISO/TR 8545:1984,Technical drawings — Installations — Graphical symbols for automatic control,Dessins techniques — Installations — Symboles graphiques pour systèmes de commande automatiques,1984-05-01,1,"['01.080.30','01.100.30']",ISO/TC 10/SC 10,9599,,"[22652,22653]","['en','fr']",6,"<p>The majority of symbols are shown in conjunction with their corresponding functional connection lines. The size of the symbols shall be related to the scale of the drawing. If a more detailed representation is required, symbols can be combined with designations indicated on the drawing or in a separate schedule. For representation on flow sheets for more advanced process systems, ISO 3511/1 is reco

15803,TR,,ISO/TR 8550:1994,"Guide for the selection of an acceptance sampling system, scheme or plan for inspection of discrete items in lots","Guide pour la sélection d'un système, d'un programme ou d'un plan d'échantillonnage pour acceptation pour le contrôle d'unités discrètes en lots",1994-03-03,1,['03.120.30'],ISO/TC 69/SC 5,9599,,"[40592,40593,40591]","['en','fr']",48,"<p>Describes the selection process, general considerations influencing a selection, making a comparison of the methods for sampling inspection, other methods sometimes adopted in practice, market and production conditions - effect on the selection process, the final selection. Is applicable to a wide variety of inspectio

15912,TR,,ISO/TR 8607:1991,Artificial insemination of animals — Frozen semen of breeding bulls — Enumeration of living aerobic micro-organisms,Insémination artificielle des animaux — Semences congelées de taureaux reproducteurs — Dénombrement des micro-organismes aérobies vivants,1991-04-25,1,['65.020.30'],ISO/TC 34,9599,,[33751],"['en','fr']",3,"<p>The method described counts the colonies obtained in a solid medium after aerobic incubation at 37 °C. Specifies normative references, definitions, principle, culture medium and diluent, apparatus and glassware, sampling, preparation of the test sample, procedure, expression of results, repeatability and test report.</p>"

15919,TR,,ISO/TR 8612:1997,Ophthalmic optics and instruments — Tonometers,Instruments ophtalmiques — Tonomètres,1997-06-12,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[29653],['en'],45,

16009,TR,,ISO/TR 8646:1985,Explanatory notes on ISO 281/1-1977,Notes explicatives sur l'ISO 281/1-1977,1985-02-14,1,['21.100.20'],ISO/TC 4/SC 8,9599,,"[43028,40622]","['en','fr']",40,<p>Gives supplementary background information regarding the derivation of formulae and factors given in ISO 282/1.</p>

55745,TR,,ISO/TR 8713:2012,Electrically propelled road vehicles — Vocabulary,Véhicules routiers électriques — Vocabulaire,2012-04-25,1,"['43.120','01.040.43']",ISO/TC 22/SC 37,9599,[38307],[71402],"['en','ru']",10,"<p>ISO/TR 8713:2012 establishes a vocabulary of terms and the related definitions used in ISO TC22/SC21 standards. These terms are specific to the electric propulsion systems of electrically propelled road vehicles, i. e. battery electric vehicles (BEV), hybrid electric vehicles (HEV, PHEV), and (pure and hybrid electric) fuel cell vehicles (FCV, FCHEV).</p>"

16207,TR,,ISO/TR 8783:1985,Alpine skis — Guidelines for conducting slope performance tests,Skis alpins — Principes directeurs pour la réalisation d'essais de performance sur piste,1985-11-07,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[29963],"['en','fr']",4,

16336,TR,,ISO/TR 8857:1986,Road vehicles — Flashers — Functional allocation of terminals,Véhicules routiers — Centrales clignotantes — Affectation fonctionnelle des bornes,1986-02-20,1,['43.040.20'],ISO/TC 22,9599,,[24782],"['en','fr']",3,

16466,TR,,ISO/TR 8942:1988,Rubber compounding ingredients — Carbon black — Determination of individual pellet crushing strength,Ingrédients de mélange du caoutchouc — Noir de carbone — Détermination de la force d'écrasement des granules individuels,1988-01-21,1,['83.040.20'],ISO/TC 45/SC 3,9599,,"[44319,45400]","['en','fr']",3,"<p>Defines the method as an interim method because the reproducibility between various laboratories is still too different. The crushing strength of individual pellets can affect the dispersion of carbon black in polymers, on bulk handling, and on conveying properties.</p>"

16477,TR,,ISO/TR 8953:1987,Tractors and self-propelled machines for agriculture and forestry— Test method for performance of air-conditioning system,Tracteurs et machines automotrices agricoles et forestiers — Méthode d'essai des performances des systèmes de conditionnement d'air,1987-11-12,1,['65.060.01'],ISO/TC 23/SC 2,9599,,"[26556,26553,24038,26554,26555]","['en','fr']",6,

16599,TR,,ISO/TR 9038:1991,Paints and varnishes — Determination of the ability of liquid paints to sustain combustion,Peintures et vernis — Détermination de l'aptitude des peintures liquides à entretenir la combustion,1991-09-19,1,"['13.220.40','87.040']",ISO/TC 35/SC 9,9599,,[26988],"['en','fr']",4,<p>Describes a pass/fail procedure for use with paint and related products to determine whether or not a product has the ability to sustain combustion under specified conditions.</p>

16666,TR,,ISO/TR 9080:1992,Thermoplastics pipes for the transport of fluids — Methods of extrapolation of hydrostatic stress rupture data to determine the long-term hydrostatic strength of thermoplastics pipe materials,"Tubes thermoplastiques pour le transport des fluides — Méthode d'extrapolation des essais de rupture sous pression, en vue de la détermination de la résistance à long terme des matières thermoplastiques pour les tubes",1992-07-16,1,['23.040.20'],ISO/TC 138/SC 5,9599,,[28314],"['en','fr']",41,<p>The two methods described are applicable to all known types of thermoplastics and cross-linked thermoplastics pipes at any temperature and to any practicable test medium. They were dev

33886,TR,Cor,ISO/TR 9080:1992/Cor 1:1995,Thermoplastics pipes for the transport of fluids — Methods of extrapolation of hydrostatic stress rupture data to determine the long-term hydrostatic strength of thermoplastics pipe materials — Technical Corrigendum 1,"Tubes thermoplastiques pour le transport des fluides — Méthode d'extrapolation des essais de rupture sous pression, en vue de la détermination de la résistance à long terme des matières thermoplastiques pour les tubes — Rectificatif technique 1",1995-08-15,1,['23.040.20'],ISO/TC 138/SC 5,9599,,[28314],['fr'],,

16717,TR,,ISO/TR 9122-1:1989,Toxicity testing of fire effluents — Part 1: General,Essais de toxicité des effluents du feu — Partie 1: Généralités,1989-09-28,1,['13.220.99'],ISO/TC 92/SC 3,9599,[12937],[33867],"['en','fr']",18,<p>Designed to provide essential information to all those involved with the evaluation of the toxicity of fire effluents not only in the development of meaningful test procedures but also in their use for mitigating hazards. Includes definitions and abbreviations.</p>

16719,TR,,ISO/TR 9122-3:1993,Toxicity testing of fire effluents — Part 3: Methods for the analysis of gases and vapours in fire effluents,Essais de toxicité des effluents du feu — Partie 3: Méthodes d'analyse des gaz et des vapeurs dans les effluents du feu,1993-05-13,1,['13.220.99'],ISO/TC 92/SC 3,9599,,"[19049,33862]","['en','fr']",34,"<p>Specifies methods for the individual analysis of airborne concentrations of carbon monoxide (CO), carbon dioxide (CO₂), oxygen (O₂), hydrogen cyanide (HCN), hydrogen chloride (HCl), hydrogen bromide (HBr), hydrogen fluoride (HF), oxides of nitrogen (NO_x), and acrolein (CH₂CHCHO) in fire effluents. Annex A gives

2536,TR,,ISO/TR 9122-4:1993,Toxicity testing of fire effluents — Part 4: The fire model (furnaces and combustion apparatus used in small-scale testing),Essais de toxicité des effluents du feu — Partie 4: Modèle feu (fours et appareillages de combustion utilisés dans les essais à petite échelle),1993-05-06,1,['13.220.99'],ISO/TC 92/SC 3,9599,,[33861],"['en','fr']",14,"<p>Defines the criteria for an acceptable fire model, reviews existing fire models ('box' furnace models, tube furnace models, radiant heat models) against these criteria, and proposes that fire models be selected for use through consideration of these criteria which includes a capacity to generate fire conditions characteristic

2458,TR,,ISO/TR 9122-6:1994,Toxicity testing of fire effluents — Part 6: Guidance for regulators and specifiers on the assessment of toxic hazards in fires in buildings and transport,Essais de toxicité des effluents du feu — Partie 6: Directives destinées aux législateurs et aux spécificateurs pour l'évaluation du risque de toxicité des incendies dans les bâtiments et dans le transport,1994-02-03,1,['13.220.99'],ISO/TC 92/SC 3,9599,,[33867],"['en','fr']",8,"<p>Describes the position of the regulator, a series of logical steps to be considered in assessing a particular fire scenario, toxic products and mechanisms of toxicity in fires, methods of toxic hazard assessment, and the recommended ha

16720,TR,,ISO/TR 9123:1986,Liquid flow measurements in open channels — Stage-fall-discharge relations,Mesure de débit des liquides dans les canaux découverts — Relations hauteur-chute-débit,1986-11-27,1,['17.120.20'],ISO/TC 113/SC 1,9599,,[29455],"['en','fr']",10,"<p>Specifies methods for determining stage-fall-discharge relations for a stream reach where variable backwater occurs either intermittently or continuously. Two gauging stations, a base reference gauge and an auxiliary gauge are required for stage measurements. A number of discharge measurements are required in order to calibrate the rating to the accuracy required by this Technical Report.</p>"

16837,TR,,ISO/TR 9210:1992,Measurement of liquid flow in open channels — Measurement in meandering rivers and in streams with unstable boundaries,Mesure de débit des liquides dans les canaux découverts — Mesurage en rivières à méandres et en cours d'eau à limites instables,1992-06-18,1,['17.120.20'],ISO/TC 113,9599,,[64747],"['en','fr']",4,"<p>Provides guidelines for discharge measurements (especially for site selection) in meandering and braided rivers, and from bridges, following the provisions of ISO 748.</p>"

16839,TR,,ISO/TR 9212:1992,Measurement of liquid flow in open channels — Methods of measurement of bedload discharge,Mesure de débit des liquides dans les canaux découverts — Méthodes de mesurage du débit des matériaux charriés sur le fond,1992-10-29,1,['17.120.20'],ISO/TC 113/SC 6,9599,,[40460],"['en','fr']",20,"<p>Reviews the current status of direct and indirect bedload measurement techniques. The methods are mainly based on size distribution of the bedload material, channel width, depth and flow velocity. Includes discussion of various types of sampling devices and site selection.</p>"

40460,TR,,ISO/TR 9212:2006,Hydrometry — Measurement of liquid flow in open channels — Methods of measurement of bedload discharge,Hydrométrie — Mesurage du débit des liquides dans les canaux découverts — Méthodes de mesurage du débit des matériaux charriés sur le fond,2006-07-21,2,['17.120.20'],ISO/TC 113/SC 6,9599,[16839],[62157],['en'],17,"<p>ISO/TR 9212:2006 reviews the current status of direct and indirect bedload-measurement techniques. The methods are mainly based on grain size distribution of the bedload, channel width, depth and velocity of flow. ISO/TR 9212:2006 outlines and explains several methods for direct and indirect measurement of bedload in streams, including various types o

52712,TR,,ISO/TR 9241-100:2010,Ergonomics of human-system interaction — Part 100: Introduction to standards related to software ergonomics,Ergonomie de l'interaction homme-système — Partie 100: Introduction aux normes relatives à l'ergonomie des logiciels,2010-01-12,1,"['13.180','35.180']",ISO/TC 159/SC 4,9599,,[84402],"['en','fr']",19,"<p>ISO 9241-100:2010 enables users of standards related to software ergonomics to identify ergonomics standards particularly relevant to software development, gain an overview on the content of software-ergonomics standards, understand the role of software-ergonomics standards in specifying user requirements as well as designing and evaluating user interfaces

16922,TR,,ISO/TR 9272:1986,Rubber and rubber products — Determination of precision for test method standards,Caoutchouc et produits en caoutchouc — Détermination de la fidélité de méthodes d'essai normalisées,1986-10-16,1,"['83.060','83.140.01']",ISO/TC 45/SC 2,9599,,[36984],"['en','fr']",30,

36984,TR,,ISO/TR 9272:2005,Rubber and rubber products — Determination of precision for test method standards,Caoutchouc et produits en caoutchouc — Évaluation de la fidélité des méthodes d'essai normalisées,2005-08-05,2,"['83.060','83.140.01']",ISO/TC 45/SC 2,9599,[16922],[66785],"['en','ru']",78,"<p>ISO/TR 9272:2005 presents guidelines for determining, by means of interlaboratory test programmes (ITPs), precision for test method standards used in the rubber manufacturing and the carbon black industries. It uses the basic one-way analysis of variance calculation algorithms of ISO 5725 and as many of the terms and definitions of ISO 5725 as possible that do not conflict with the past history

16924,TR,,ISO/TR 9274:1991,Rolling bearings — Measuring and gauging principles and methods,Roulements — Principes et méthodes de mesurage et de vérification par calibres,1991-02-28,1,['21.100.20'],ISO/TC 4/SC 4,9599,,[30157],"['en','fr']",11,"<p>Establishes guidelines for measurement of dimensions, running accuracy and internal clearance of both radial and thrust rolling bearings. The purpose is to outline the fundamentals of various measuring and gauging principles which may be used in order to comply with the definitions of ISO 1132 and ISO 5593. The methods described in this Technical Report do differ amongst themselves and there are other adequate measuring and gauging methods. ISO/TR 92

17104,TR,,ISO/TR 9405:1990,Textile floor coverings — Assessment of changes in appearance,Revêtements de sol textiles — Évaluation des changements d'aspect,1990-09-06,1,['97.150'],ISO/TC 219,9599,,[26836],"['en','fr']",5,

17112,TR,,ISO/TR 9412:1991,Portable chain-saws — Automatic chain brake and cutting equipment — Operator's safety test,Scies à chaîne portatives — Frein de chaîne automatique et équipement de coupe — Essai de sécurité de l'opérateur,1991-03-14,1,['65.060.80'],ISO/TC 23/SC 17,9599,,[21698],"['en','fr']",8,

17194,TR,,ISO/TR 9464:1998,Guidelines for the use of ISO 5167-1:1991,Lignes directrices pour l'utilisation de l'ISO 5167-1:1991,1998-04-30,1,['17.120.10'],ISO/TC 30/SC 2,9599,,[40031],['en'],74,

40031,TR,,ISO/TR 9464:2008,Guidelines for the use of ISO 5167:2003,Lignes directrices pour l'utilisation de l'ISO 5167:2003,2008-05-20,2,['17.120.10'],ISO/TC 30/SC 2,9599,[17194],[85583],['en'],68,<p>ISO/TR 9464:2008 provides guidance on the use of ISO 5167:2003 (all parts). ISO 5167:2003 is an International Standard for flow measurement based on the differential pressure generated by a constriction introduced into a circular conduit. It presents a set of rules and requirements based on theory and experimental work undertaken in the field of flow measurement.</p>

22799,TR,,ISO/TR 9527:1994,Building construction — Needs of disabled people in buildings — Design guidelines,Construction immobilière — Besoins des handicapés dans les bâtiments — Lignes directrices pour la conception,1994-09-01,1,"['11.180.10','91.040.01']",ISO/TC 59,9599,,[50498],"['en','fr']",24,"<p>Deals with the problems of the handicapped in buildings, as far as they present practical challenges to designers and architects. Provides some guidance for planners and for the formulation of local regulation, standards, recommendations etc. not in the form of a standard but in the form of a general account of basic and particular needs.</p>"

36761,TR,,ISO/TR 9564-4:2004,Banking — Personal Identification Number (PIN) management and security — Part 4: Guidelines for PIN handling in open networks,Banque — Gestion et sécurité du numéro personnel d'identification (PIN) — Partie 4: Directives sur la manipulation du PIN dans les dispositifs à réseau ouvert,2004-03-15,1,['35.240.40'],ISO/TC 68/SC 2,9599,,[61246],['en'],6,"<p>ISO/TR 9564-4:2004 provides guidelines for personal identification number PIN handling in open networks, presenting finance industry best-practice security measures for PIN management and the handling of financial card originated transactions in environments where issuers and acquirers have no direct control over ma

17352,TR,,ISO/TR 9586:1988,Implants for surgery — Usage of terms 'valgus' and 'varus' in orthopaedic surgery,Implants chirurgicaux — Usage des termes 'valgus' et 'varus' en chirurgie orthopédique,1988-12-01,1,['11.040.40'],ISO/TC 150,9599,,[67930],"['en','fr']",6,"<p>Both terms have been in use for centuries but their meaning seams to have varied from time to time. The present usage has developed in a haphazard manner, such that consistent definition of the terms seems to be impossible. This Technical Report points out the differences in usage of both terms so that anomalies of usage, espacially in relation to the hip joint, may be clearly understood and confusion minimized.</p>"

17628,TR,,ISO/TR 9769:1988,Steel and iron — Review of available methods of analysis,Aciers et fontes — Vue d'ensemble des méthodes d'analyse disponibles,1988-07-21,1,['77.080.01'],ISO/TC 17/SC 1,9599,,[17629],"['en','fr']",,

17629,TR,,ISO/TR 9769:1990,Steel and iron — Review of available methods of analysis,Aciers et fontes — Vue d'ensemble des méthodes d'analyse disponibles,1990-02-15,2,['77.080.01'],ISO/TC 17/SC 1,9599,[17628],[17630],"['en','fr']",24,

17630,TR,,ISO/TR 9769:1991,Steel and iron — Review of available methods of analysis,Aciers et fontes — Vue d'ensemble des méthodes d'analyse disponibles,1991-10-24,3,['77.080.01'],ISO/TC 17/SC 1,9599,[17629],"[74711,63308]","['en','fr']",30,"<p>Refers to the available international standard method(s) for the determination of required element(s) in steel and iron. States the field of application, the method of determination (principle), and the precision of each standard. This third edition cancels and replaces the second edition (1990).</p>"

17635,TR,,ISO/TR 9774:1990,Thermal-insulation materials — Application categories and basic requirements — Guidelines for the harmonization of International Standards and other specifications,Produits isolants thermiques pour le bâtiment — Catégories d'applications et caractéristiques relatives aux performances maximales — Guide pour l'harmonisation des Normes internationales et autres spécifications,1990-10-11,1,"['83.100','91.100.60']",ISO/TC 61/SC 10,9599,,[29776],"['en','fr']",4,

17636,IS,Cor,ISO/TR 9774:1990/Cor 1:1991,Thermal-insulation materials — Application categories and basic requirements — Guidelines for the harmonization of International Standards and other specifications — Technical Corrigendum 1,Produits isolants thermiques pour le bâtiment — Catégories d'applications et caractéristiques relatives aux performances maximales — Guide pour l'harmonisation des Normes internationales et autres spécifications — Rectificatif technique 1,1991-12-12,1,['83.100'],ISO/TC 61/SC 10,9599,,[29776],['en'],1,"<p>Table 3: in the 'Performance characteristics' column, line f, right-hand side, replace 'between 20°C' by 'between 20°C and 60°C'.</p>"

17652,TR,,ISO/TR 9790-1:1989,Road vehicles — Anthropomorphic side impact dummy — Part 1: Lateral head impact response requirements to assess biofidelity of dummy,Véhicules routiers — Mannequin anthropomorphe pour essai de choc latéral — Partie 1: Caractéristiques de réponse de la tête à un choc latéral permettant d'évaluer la biofidélité d'un mannequin,1989-05-03,1,['43.180'],ISO/TC 22,9599,,[29828],"['en','fr']",5,

17653,TR,,ISO/TR 9790-2:1989,Road vehicles — Anthropomorphic side impact dummy — Part 2: Lateral neck impact response requirements to assess biofidelity of dummy,Véhicules routiers — Mannequin anthropomorphe pour essai de choc latéral — Partie 2: Caractéristiques de réponse du cou à un choc latéral permettant d'évaluer la biofidélité d'un mannequin,1989-05-03,1,['43.180'],ISO/TC 22,9599,,[29828],"['en','fr']",11,

17654,TR,,ISO/TR 9790-3:1989,Road vehicles — Anthropomorphic side impact dummy — Part 3: Lateral thoracic impact response requirements to assess biofidelity of dummy,Véhicules routiers — Mannequin anthropomorphe pour essai de choc latéral — Partie 3: Caractéristiques de réponse du thorax à un choc latéral permettant d'évaluer la biofidélité d'un mannequin,1989-05-03,1,['43.180'],ISO/TC 22,9599,,[29828],"['en','fr']",18,

17655,TR,,ISO/TR 9790-4:1989,Road vehicles — Anthropomorphic side impact dummy — Part 4: Lateral shoulder impact response requirements to assess biofidelity of dummy,Véhicules routiers — Mannequin anthropomorphe pour essai de choc latéral — Partie 4: Caractéristiques de réponse de l'épaule à un choc latéral permettant d'évaluer la biofidélité d'un mannequin,1989-05-03,1,['43.180'],ISO/TC 22,9599,,[29828],"['en','fr']",7,

17656,TR,,ISO/TR 9790-5:1989,Road vehicles — Anthropomorphic side impact dummy — Part 5: Lateral abdominal impact response requirements to assess biofidelity of dummy,Véhicules routiers — Mannequin anthropomorphe pour essai de choc latéral — Partie 5: Caractéristiques de réponse de l'abdomen à un choc latéral permettant d'évaluer la biofidélité d'un mannequin,1989-05-03,1,['43.180'],ISO/TC 22,9599,,[29828],"['en','fr']",14,

17657,TR,,ISO/TR 9790-6:1989,Road vehicles — Anthropomorphic side impact dummy — Part 6: Lateral pelvic impact response requirements to assess biofidelity of dummy,Véhicules routiers — Mannequin anthropomorphe pour essai de choc latéral — Partie 6: Caractéristiques de réponse du bassin à un choc latéral permettant d'évaluer la biofidélité d'un mannequin,1989-05-03,1,['43.180'],ISO/TC 22,9599,,[29828],"['en','fr']",18,

17694,TR,,ISO/TR 9824-1:1990,Measurement of free surface flow in closed conduits — Part 1: Methods,Mesurage du débit des écoulements à surface dénoyée dans les conduites fermées — Partie 1: Méthodes,1990-05-10,1,['17.120.10'],ISO/TC 113/SC 1,9599,,"[37575,44741]","['en','fr']",7,

17695,TR,,ISO/TR 9824-2:1990,Measurement of free surface flow in closed conduits — Part 2: Equipment,Mesurage du débit des écoulements à surface dénoyée dans les conduites fermées — Partie 2: Matériels,1990-05-10,1,['17.120.10'],ISO/TC 113/SC 5,9599,,"[37575,44741]","['en','fr']",5,

17784,TR,,ISO/TR 9901:1990,Solar energy — Field pyranometers — Recommended practice for use,Énergie solaire — Pyranomètres de champ — Pratique recommandée pour l'emploi,1990-08-23,1,['27.160'],ISO/TC 180/SC 1,9599,,"[81937,77126]",['en'],15,

17906,TR,,ISO/TR 9993:1989,Plain bearings — Testing of the tribological behaviour of bearing materials for oil lubrication application — Running-in under mixed lubrication conditions,Paliers lisses — Essai de propriétés tribologiques des matériaux pour paliers lubrifiés à l'huile — Aptitude au rodage dans des conditions de lubrification en régime mixte,1989-12-14,1,['21.100.10'],ISO/TC 123/SC 2,9599,,[20994],"['en','fr']",5,

38063,TS,,ISO/TS 10004:2010,Quality management — Customer satisfaction — Guidelines for monitoring and measuring,Management de la qualité — Satisfaction du client — Lignes directrices relatives à la surveillance et au mesurage,2010-04-08,1,['03.120.10'],ISO/TC 176/SC 3,9599,,[56869],"['en','fr']",29,"<p>ISO/TS 10004:2010 provides guidance in defining and implementing processes to monitor and measure customer satisfaction. </p><p>ISO/TS 10004:2010 is intended for use by organizations regardless of type, size or product provided. The focus of ISO/TS 10004:2010 is on customers external to the organization.</p><p>ISO/TS 10004:2010 is not intended for certification or contractual purposes, nor is

45831,TS,,ISO/TS 10128:2009,Graphic technology — Methods of adjustment of the colour reproduction of a printing system to match a set of characterization data,Technologie graphique — Méthodes d'ajustage de la reproduction de couleurs d'un système d'impression pour correspondre à un ensemble de données de caractérisation,2009-06-30,1,['37.100.10'],ISO/TC 130,9599,,[83513],['en'],12,"<p>ISO/TS 10128:2009 specifies three methods for the adjustment of the digital content data that is input to a printing system to achieve consistency in the printed results among a number of presses printing to the same general aim conditions. These three methods are generally identified as </p><ol><li> the match

37092,TS,,ISO/TS 10272-2:2006,Microbiology of food and animal feeding stuffs — Horizontal method for detection and enumeration of Campylobacter spp. — Part 2: Colony-count technique,Microbiologie des aliments — Méthode horizontale pour la recherche et le dénombrement de Campylobacter spp. — Partie 2: Technique par comptage des colonies,2006-01-19,1,['07.100.30'],ISO/TC 34/SC 9,9599,"[18312,27218,29295]",[63228],"['en','fr']",13,"<p>ISO/TS 10272-2:2006 describes a horizontal method for the enumeration of <i>Campylobacter </i>spp. </p><p>It is applicable to products intended for human consumption or for the feeding of animals, and to environmental samples in the area of food production and foo

33602,TS,,ISO/TS 10303-1001:2001,Industrial automation systems and integration — Product data representation and exchange — Part 1001: Application module: Appearence assignment,Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 1001: Module d'application: Attribution d'apparence,2001-09-20,1,['25.040.40'],ISO/TC 184/SC 4,9599,,[39878],['en'],27,

39878,TS,,ISO/TS 10303-1001:2004,Industrial automation systems and integration — Product data representation and exchange — Part 1001: Application module: Appearance assignment,Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 1001: Module d'application: Attribution d'apparence,2004-12-16,2,['25.040.40'],ISO/TC 184/SC 4,9599,[33602],[44785],['en'],31,<p>ISO/TS 10303-1001:2004 specifies the application module Appearance assignment. </p> <p> The following are within the scope of ISO/TS 10303-1001:2004: </p> <ul> <li>definition of the visual characteristi

44785,TS,,ISO/TS 10303-1001:2006,Industrial automation systems and integration — Product data representation and exchange — Part 1001: Application module: Appearance assignment,Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 1001: Module d'application: Attribution d'apparence,2006-12-12,3,['25.040.40'],ISO/TC 184/SC 4,9599,[39878],[52540],['en'],40,<p>ISO/TS 10303-1001:2006 specifies the application module for Appearance assignment. </p> <p> The following are within the scope of ISO/TS 10303-1001:2006: </p> <ul> <li>definition of the visual character

52540,TS,,ISO/TS 10303-1001:2008,Industrial automation systems and integration — Product data representation and exchange — Part 1001: Application module: Appearance assignment,Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 1001: Module d'application: Attribution d'apparence,2008-12-15,4,['25.040.40'],ISO/TC 184/SC 4,9599,[44785],[56825],['en'],46,"<p>ISO/TS 10303-1001:2008 specifies the application module for Appearance assignment. </p> <p> The following are within the scope of ISO/TS 10303-1001:2008: </p> <ul> <li>definition of the visual characte

56825,TS,,ISO/TS 10303-1001:2010,Industrial automation systems and integration — Product data representation and exchange — Part 1001: Application module: Appearance assignment,Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 1001: Module d'application: Attribution d'apparence,2010-09-03,5,['25.040.40'],ISO/TC 184/SC 4,9599,[52540],[64301],['en'],11,"<p>ISO/TS 10303-1001:2010-07 specifies the application module for Appearance assignment. </p> <p> The following are within the scope of ISO/TS 10303-1001:2010-07: </p> <ul> <li>definition of the visual ch

64301,TS,,ISO/TS 10303-1001:2014,Industrial automation systems and integration — Product data representation and exchange — Part 1001: Application module: Appearance assignment,Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 1001: Module d'application: Attribution d'apparence,2014-11-18,6,['25.040.40'],ISO/TC 184/SC 4,9599,[56825],[76141],['en'],11,"<p>ISO/TS 10303-1001:2014-02 specifies the application module for Appearance assignment. </p> <p> The following are within the scope of ISO/TS 10303-1001:2014-02: </p> <ul> <li>definition of the visual ch

76141,TS,,ISO/TS 10303-1001:2018,Industrial automation systems and integration — Product data representation and exchange — Part 1001: Application module: Appearance assignment,Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 1001: Module d'application: Attribution d'apparence,2018-12-18,7,['25.040.40'],ISO/TC 184/SC 4,9599,[64301],[78596],['en'],11,"<p>ISO/TS 10303-1001:2018-11 specifies the application module for Appearance assignment. </p> <p> The following are within the scope of ISO/TS 10303-1001:2018-11: </p> <ul> <li>definition of the visual ch

78596,TS,,ISO/TS 10303-1001:2019,Industrial automation systems and integration — Product data representation and exchange — Part 1001: Application module: Appearance assignment,Systèmes d'automatisation industrielle et intégration — Représentation et échange de données de produits — Partie 1001: Module d'application: Attribution d'apparence,2019-11-15,8,['25.040.40'],ISO/TC 184/SC 4,9599,[76141],[89544],['en'],11,"<p>ISO/TS 10303-1001:2019 specifies the application module for Appearance assignment. </p> <p> The following are within the scope of ISO/TS 10303-1001:2019: </p> <ul> <li>definition of the visual characte