Withdrawn and superseded ISO standards — page 189 of 246

17837,IS,,ISO 9942-1:1994,Cranes — Information labels — Part 1: General,Appareils de levage à charge suspendue — Plaques descriptives — Partie 1: Généralités,1994-10-06,1,['53.020.20'],ISO/TC 96/SC 5,9599,,[67237],"['en','fr']",1,<p>Specifies the minimum requirements for labels for the identification and the operation of cranes.</p>

21211,IS,,ISO 9942-3:1999,Cranes — Information labels — Part 3: Tower cranes,Appareils de levage à charge suspendue — Plaques descriptives — Partie 3: Grues à tour,1999-09-30,1,['53.020.20'],ISO/TC 96/SC 7,9599,,[75457],"['en','fr']",2,

17838,IS,,ISO 9943:1991,Shipbuilding — Ventilation and air-treatment of galleys and pantries with cooking appliances,Construction navale — Ventilation et traitement de l'air des cuisines et offices avec appareils de cuisson à bord des navires,1991-01-17,1,['47.020.90'],ISO/TC 8/SC 3,9599,,[43036],"['en','fr']",5,"<p>Describes the design requirements and general considerations of this equipment on board merchant seagoing ships, when it is specified by the shipowner. Applies for normal conditions in all waters except those encountered in extremely cold or hot climates. Herein, pantries with cooking appliances are those which contain appliances consuming more than the small amount of electrical

17842,IS,,ISO 9946:1991,Manipulating industrial robots — Presentation of characteristics,Robots manipulateurs industriels — Présentation des caractéristiques,1991-02-14,1,['25.040.30'],ISO/TC 184,9599,,[28794],"['en','fr']",12,

17843,IS,,ISO 9947:1991,Textile machinery and accessories — Two-for-one twisters — Vocabulary,Matériel pour l'industrie textile — Retordeuses à broches 'double torsion' — Vocabulaire,1991-08-15,1,"['01.040.59','59.120.10']",ISO/TC 72/SC 1,9599,,[38585],"['en','fr']",10,<p>Specifies terms and definitions in English and French. Annexes A (German terms and definitions) and B are for information only.</p>

17844,IS,,ISO 9948:1992,Truck and bus tyres — Methods of measuring rolling resistance,Pneumatiques pour camions et autobus — Méthodes de mesure de la résistance au roulement,1992-10-29,1,['83.160.10'],ISO/TC 31/SC 4,9599,,[33328],"['en','fr']",11,"<p>Applies to all truck and bus pneumatic tyres. In measuring tyre rolling resistance, it is necessary to measure small forces in the presence of much larger forces. It is, therefore, essential that equipment and instrumentation of appropriate accuracy be used. Annex A gives test equipment tolerances, annexes B and C (informative) describe optional test conditions and measurement methods of moment of inertia.</p>"

5439,IS,,ISO 995:1975,Potassium hydroxide for industrial use — Determination of silica content — Reduced molybdosilicate photometric method,Hydroxyde de potassium à usage industriel — Dosage de la silice — Méthode photométrique au molybdosilicate réduit,1975-09-01,1,['71.060.40'],ISO/TC 47,9599,,[5440],"['en','fr']",3,"<p>The method is applicable to products having silica contents exceeding 10 mg/kg. The principle is based on the formation of yellow oxidized silico-molybdic complex in a strongly acid medium, in the presence of boric acid to suppress interference by fluorides. Selective reduction of this complex with a mixture of aminonaphtholsulphonic acid (4-amino-3-hydroxynaphthalene-1-sul

17850,IS,,ISO 9952:1993,Agricultural irrigation equipment— Check valves,Matériel agricole d'irrigation — Clapets antiretour,1993-03-18,1,['65.060.35'],ISO/TC 23/SC 18,9599,,[41123],"['en','fr']",8,"<p>Specifies the construction and performance requirements (classification, mechanism, installation, marking, valve body length, connections), and test methods (resistance to internal hydrostatic pressure, tightness, valve opening after tightness test, pressure loss, endurance, tightness after mechanical endurance test) for check valves of nominal sizes 15 mm (0,5 in) up to and including 300 mm (12 in) intended for operation with water at temperatures not exceeding 50 °C, which may contain fertili

17854,IS,,ISO 9956-1:1995,Specification and approval of welding procedures for metallic materials — Part 1: General rules for fusion welding,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 1: Règles générales pour le soudage par fusion,1995-08-24,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28388],"['en','fr']",6,"<p>Defines general rules for the specification and approval of welding procedures for metallic materials. Applies, when approval of a welding procedure is required, e.g. by contract, standards etc.. Applicable by conventional welding equipment under direct control of the welder.</p>"

27387,IS,Amd,ISO 9956-1:1995/Amd 1:1998,Specification and approval of welding procedures for metallic materials — Part 1: General rules for fusion welding — Amendment 1,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 1: Règles générales pour le soudage par fusion — Amendement 1,1998-11-05,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28388],"['en','fr']",5,

24759,IS,,ISO 9956-10:1996,Specification and approval of welding procedures for metallic materials — Part 10: Welding procedure specification for electron beam welding,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 10: Descriptif d'un mode opératoire de soudage par faisceau d'électrons,1996-09-26,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28405],"['en','fr']",8,

24758,IS,,ISO 9956-11:1996,Specification and approval of welding procedures for metallic materials — Part 11: Welding procedure specification for laser beam welding,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 11: Descriptif d'un mode opératoire de soudage par faisceau laser,1996-09-26,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28406],"['en','fr']",10,

17855,IS,,ISO 9956-2:1995,Specification and approval of welding procedures for metallic materials — Part 2: Welding procedure specification for arc welding,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 2: Descriptif d'un mode opératoire de soudage pour le soudage à l'arc,1995-08-24,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28390],"['en','fr']",4,<p>Requirements for the content of welding procedure specifications for arc welding processes. The principles may be also applied to other fusion welding processes subject to agreement.</p>

27388,IS,Amd,ISO 9956-2:1995/Amd 1:1998,Specification and approval of welding procedures for metallic materials — Part 2: Welding procedure specification for arc welding — Amendment 1,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 2: Descriptif d'un mode opératoire de soudage pour le soudage à l'arc — Amendement 1,1998-11-05,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28390],"['en','fr']",3,

17856,IS,,ISO 9956-3:1995,Specification and approval of welding procedures for metallic materials — Part 3: Welding procedure tests for arc welding of steels,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 3: Épreuve de qualification d'un mode opératoire de soudage à l'arc sur acier,1995-08-24,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28395],"['en','fr']",29,<p>Approval of a welding procedure specification for the arc welding of steels by welding procedure tests. Defines the conditions for the execution of welding procedure approval tests and the limits of validity of an approved welding procedure for all practical welding operations.</p> 1785

27389,IS,Amd,ISO 9956-3:1995/Amd 1:1998,Specification and approval of welding procedures for metallic materials — Part 3: Welding procedure tests for arc welding of steels — Amendment 1,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 3: Épreuve de qualification d'un mode opératoire de soudage à l'arc sur acier — Amendement 1,1998-11-05,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28395],"['en','fr']",15,

17857,IS,,ISO 9956-4:1995,Specification and approval of welding procedures for metallic materials — Part 4: Welding procedure tests for the arc welding of aluminium and its alloys,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 4: Épreuve de qualification d'un mode opératoire de soudage à l'arc sur l'aluminium et ses alliages,1995-08-24,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28408],"['en','fr']",22,<p>Approval of a welding procedure specification for the arc welding of aluminium and its alloys by welding procedure tests. Defines the conditions for the execution of welding procedure approval tests and the limits of validity of an approved we

27390,IS,Amd,ISO 9956-4:1995/Amd 1:1998,Specification and approval of welding procedures for metallic materials — Part 4: Welding procedure tests for the arc welding of aluminium and its alloys — Amendment 1,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 4: Épreuve de qualification d'un mode opératoire de soudage à l'arc sur l'aluminium et ses alliages — Amendement 1,1998-11-05,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28408],"['en','fr']",9,

21087,IS,,ISO 9956-5:1995,Specification and approval of welding procedures for metallic materials — Part 5: Approval by using approved welding consumables for arc welding,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 5: Qualification par utilisation de produits consommables de soudage agréés pour le soudage à l'arc,1995-09-14,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28391],"['en','fr']",4,<p>Simplifies the approval of fusion welding procedures for metallic materials using approved consumables especially suitable for repetitive operations. Identical with European Standard EN 288-5.</p>

21628,IS,,ISO 9956-6:1995,Specification and approval of welding procedures for metallic materials — Part 6: Approval related to previous experience,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 6: Qualification par référence à l'expérience acquise,1995-09-14,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28392],"['en','fr']",2,"<p>Defines the conditions for approval of a fusion welding procedure for metallic materials, based on previous experience according to ISO 9956-1. Identical with European Standard EN 288-6.</p>"

21629,IS,,ISO 9956-7:1995,Specification and approval of welding procedures for metallic materials — Part 7: Approval by a standard welding procedure for arc welding,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 7: Qualification par référence à un mode opératoire de soudage standard pour le soudage à l'arc,1995-12-27,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28393],"['en','fr']",3,<p>Defines the conditions for the approval of a standard welding procedure for arc welding and establishes the requirements necessary for the use of these procedures.</p>

21630,IS,,ISO 9956-8:1995,Specification and approval of welding procedures for metallic materials — Part 8: Approval by a pre-production welding test,Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques — Partie 8: Épreuve de qualification par exécution d'un assemblage soudé particulier préalable à la production,1995-12-27,1,['25.160.10'],ISO/TC 44/SC 10,9599,,[28394],"['en','fr']",2,"<p>Describes the conditions for the approval of a fusion welding procedure of metallic materials based on pre-production welding tests. In addition, it gives the range of approval and the validity.</p>"

21207,IS,,ISO 9957-2:1995,Fluid draughting media — Part 2: Water-based non-India ink — Requirements and test conditions,Fluides à dessin — Partie 2: Encres aqueuses autres que les encres de Chine — Prescriptions et conditions d'essai,1995-06-22,1,['01.100.40'],ISO/TC 10,9599,,[75970],"['en','fr']",5,"<p>Specifies the requirements and test conditions for water-based non-India inks intended for use in draughting instruments and intended for use on natural tracing paper conforming to ISO 9961, to provide for black line technical drawings.</p>"

17872,IS,,ISO 9965:1993,Water quality — Determination of selenium — Atomic absorption spectrometric method (hydride technique),Qualité de l'eau — Dosage du sélénium — Méthode par spectrométrie d'absorption atomique (technique hydrure),1993-07-01,1,['13.060.50'],ISO/TC 147/SC 2,9599,,[55221],"['en','fr']",5,"<p>Under the conditions of the method specified (thermal decomposition of selenium hydride for AAS), only Se(IV) is quantitatively converted to the hydride. To avoid errors in determination, other oxidation states need to be converted to Se(IV) prior to the determination. The absorbance is measured at a wavelength of 196,0 nm. The method determines selenium and organically bonded selenium

17874,IS,,ISO 9967:1994,Thermoplastics pipes — Determination of creep ratio,Tubes en matières thermoplastiques — Détermination du taux de fluage,1994-02-24,1,['23.040.20'],ISO/TC 138/SC 5,9599,,[44617],"['en','fr']",8,"<p>The principle of the method specified is placing a cut length of pipe between two parallel flat horizontal plates, applying a constant compressive force for 1000 h (42 days), recording the deflection of the pipe at specified intervals so as to prepare a plot of pipe deflection against time, analysing the linearity of the data and calculating the creep ratio. Applies to pipes having a circular cross-section.</p>"

44617,IS,,ISO 9967:2007,Thermoplastics pipes — Determination of creep ratio,Tubes en matières thermoplastiques — Détermination du taux de fluage,2007-11-08,2,['23.040.20'],ISO/TC 138/SC 5,9599,[17874],[62369],"['en','fr','ru']",12,<p>ISO 9967:2007 specifies a method for determining the creep ratio of thermoplastics pipes having a circular cross-section.</p>

17876,IS,,ISO 9969:1994,Thermoplastics pipes — Determination of ring stiffness,Tubes en matières thermoplastiques — Détermination de la rigidité annulaire,1994-02-17,1,['23.040.20'],ISO/TC 138/SC 5,9599,,[40488],"['en','fr']",5,"<p>The principle of the method specified is vertically compressing a length of pipe supported horizontally between two parallel flat plates moved at a constant speed which is dependent upon the diameter of the pipe, measuring the force and the deflection, plotting the force versus deflection, and calculating the ring stiffness as a function of the force necessary to produce a deflection of 0,03 nominal diameter diametrically across the pipe. Applies to pipes having a

40488,IS,,ISO 9969:2007,Thermoplastics pipes — Determination of ring stiffness,Tubes en matières thermoplastiques — Détermination de la rigidité annulaire,2007-12-03,2,['23.040.20'],ISO/TC 138/SC 5,9599,[17876],[62370],"['en','fr','ru']",8,<p>ISO 9969:2007 specifies a test method for determining the ring stiffness of thermoplastics pipes having a circular cross section.</p>

5442,IS,,ISO 997:1976,Potassium hydroxide for industrial use — Determination of calcium content — EDTA (disodium salt) complexometric method,Hydroxyde de potassium à usage industriel — Dosage du calcium — Méthode complexométrique à l'EDTA (sel disodique),1976-05-01,1,['71.060.40'],ISO/TC 47,9599,,[5443],"['en','fr']",3,"<p>The method is applicable to products having a calcium content equal to or greater than 0.002 % (m/m). The principle consists in titration of the calcium with a standard volumetric solution of the disodium salt of (ethylenedinitrilo)tetraacetic acid (EDTA disodium salt) in the presence of 2,2'-(ethylenedinitrilo)diphenol Äglyoxal-bis-(2-hydroxyanil)Ü as indicator, after el

17879,IS,,ISO 9972:1996,Thermal insulation — Determination of building airtightness — Fan pressurization method,Isolation thermique — Détermination de l'étanchéité à l'air des bâtiments — Méthode de pressurisation par ventilateur,1996-07-18,1,['91.120.10'],ISO/TC 163/SC 1,9599,,[36415],"['en','fr']",10,

36415,IS,,ISO 9972:2006,Thermal performance of buildings — Determination of air permeability of buildings — Fan pressurization method,Performance thermique des bâtiments — Détermination de la perméabilité à l'air des bâtiments — Méthode de pressurisation par ventilateur,2006-04-26,2,['91.120.10'],ISO/TC 163/SC 1,9599,[17879],[55718],['en'],20,"<p>ISO 9972:2006 is intended for the measurement of the air permeability of buildings or parts of buildings in the field. It specifies the use of mechanical pressurization or depressurization of a building or part of a building. It describes the measurement of the resulting air flow rates over a range of indoor-outdoor static pressure differences.</p><

52254,IS,Amd,ISO 9972:2006/Amd 1:2009,Thermal performance of buildings — Determination of air permeability of buildings — Fan pressurization method — Amendment 1,Performance thermique des bâtiments — Détermination de la perméabilité à l'air des bâtiments — Méthode de pressurisation par ventilateur — Amendement 1,2009-02-24,2,['91.120.10'],ISO/TC 163/SC 1,9599,,[55718],['en'],2,

38296,IS,,ISO 9974-4:2006,"Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 4: Dimensions, design, test methods and requirements for external hex and internal hex port plugs","Raccordements pour applications générales et transmissions hydrauliques et pneumatiques — Orifices et éléments mâles à filetage ISO 261 et joint en élastomère ou étanchéité métal sur métal — Partie 4: Dimensions, conception, méthodes d'essai et exigences des bouchons d'orifice à six pans externes et à six pans internes",2006-05-12,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[71181],"['en','fr']",10,"<p>ISO 9974-4:2006 specifies dimensions

17886,IS,,ISO 9978:1992,Radiation protection — Sealed radioactive sources — Leakage test methods,Radioprotection — Sources radioactives scellées — Méthodes d'essai d'étanchéité,1992-01-30,1,['13.280'],ISO/TC 85/SC 2,9599,,[70598],"['en','fr']",10,<p>Gives terms and definitions. Describes test methods by radioactive means and non-radioactive means. Tabulates threshold detection values and limiting values for different test methods.</p>

17888,IS,,ISO 9980:1990,Belt drives — Grooved pulleys for V-belts (system based on effective width) — Geometrical inspection of grooves,Transmissions par courroies — Poulies à gorges pour courroies trapézoïdales (système basé sur la largeur effective) — Contrôle géométrique des gorges,1990-09-20,1,['21.220.10'],ISO/TC 41/SC 1,9599,,"[26542,60851]","['en','fr']",8,

17889,IS,,ISO 9981:1990,Belt drives — Pulleys and V-ribbed belts for the automotive industry — Dimensions — PK profile,Transmissions par courroies — Poulies et courroies striées pour la construction automobile — Dimensions — Profil PK,1990-11-22,1,"['43.060.10','21.220.10']",ISO/TC 41/SC 1,9599,,[27602],"['en','fr']",6,

27602,IS,,ISO 9981:1998,Belt drives — Pulleys and V-ribbed belts for the automotive industry — PK profile: Dimensions,Transmissions par courroies — Poulies et courroies striées pour la construction automobile — Profil PK: Dimensions,1998-10-29,2,['43.060.10'],ISO/TC 41/SC 1,9599,[17889],[70616],"['en','fr']",8,

17890,IS,,ISO 9982:1991,"Belt drives — Pulleys and V-ribbed belts for industrial applications — Dimensions — PH, PJ, PK, PL and PM profiles","Transmissions par courroies — Poulies et courroies striées pour des applications industrielles — Dimensions — Profils PH, PJ, PK, PL et PM",1991-01-31,1,['21.220.10'],ISO/TC 41/SC 1,9599,,[25805],"['en','fr']",7,

25805,IS,,ISO 9982:1998,"Belt drives — Pulleys and V-ribbed belts for industrial applications — PH, PJ, PK, PL and PM profiles: dimensions","Transmissions par courroies — Poulies et courroies striées pour des applications industrielles — Dimensions — Profils PH, PJ, PK, PL et PM",1998-06-18,2,['21.220.10'],ISO/TC 41/SC 1,9599,[17890],[82249],"['en','fr']",11,

17892,IS,,ISO 9984:1996,Information and documentation — Transliteration of Georgian characters into Latin characters,Information et documentation — Translittération des caractères géorgiens en caractères latins,1996-12-26,1,['01.140.10'],ISO/TC 46,9599,,[87131],"['en','fr']",7,"<p>Establishes a system for the transliteration of Georgian characters into Latin characters to permit international information exchange, particularly by electronic means.</p>"

17893,IS,,ISO 9985:1996,Information and documentation — Transliteration of Armenian characters into Latin characters,Information et documentation — Translittération des caractères arméniens en caractères latins,1996-12-26,1,['01.140.10'],ISO/TC 46,9599,,"[29709,87132]","['en','fr']",7,"<p>Establishes a system for the transliteration of the modern Armenian alphabet into Latin characters to permit international information exchange, particularly by electronic means.</p>"

17894,IS,,ISO 9986:1990,Composition cork for shoe outsoles,Aggloméré composé de liège pour semelles extérieures pour chaussure,1990-10-25,1,"['61.060','79.100']",ISO/TC 87,9599,,[62403],"['en','fr']",3,<p>Specifies requirements for test methods for composition cork for the manufacture of outsoles of shoes and boots.</p>

17896,IS,,ISO 9988-1:1991,Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 1: Designation,Plastiques — Thermoplastiques à base de polyoxyméthylène (POM) pour moulage et extrusion — Partie 1: Désignation,1991-02-07,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[27080],"['en','fr']",4,

27080,IS,,ISO 9988-1:1998,Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Matériaux à base de polyoxyméthylène (POM) pour moulage et extrusion — Partie 1: Système de désignation et base de spécification,1998-11-12,2,['83.080.20'],ISO/TC 61/SC 9,9599,[17896],[40594],"['en','fr']",6,

40594,IS,,ISO 9988-1:2004,Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 1: Designation system and basis for specifications,Plastiques — Matériaux à base de polyoxyméthylène (POM) pour moulage et extrusion — Partie 1: Système de désignation et base de spécification,2004-09-03,3,['83.080.20'],ISO/TC 61/SC 9,9599,[27080],[68341],"['en','fr']",6,"<p>ISO 9988-1:2004 establishes a system of designation for polyoxymethylene (POM) thermoplastic materials, which may be used as the basis for specifications.</p><p>The types of polyoxymethylene plastic are differentiated from each other by a classification system based on appropriate levels of the following designatory proper

17897,IS,,ISO 9988-2:1991,Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Thermoplastiques à base de polyoxyméthylène (POM) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des caractéristiques,1991-05-16,1,['83.080.20'],ISO/TC 61/SC 9,9599,,[26817],"['en','fr']",3,

26817,IS,,ISO 9988-2:1999,Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Matériaux à base de polyoxyméthylène (POM) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés,1999-12-16,2,['83.080.20'],ISO/TC 61/SC 9,9599,[17897],[41674],"['en','fr']",5,

41674,IS,,ISO 9988-2:2006,Plastics — Polyoxymethylene (POM) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Matériaux à base de polyoxyméthylène (POM) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés,2006-07-13,3,['83.080.20'],ISO/TC 61/SC 9,9599,[26817],[68340],"['en','fr']",5,"<p>ISO 9988-2:2006 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polyoxymethylene moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the spe

17898,IS,,ISO 9989:1996,Determination of uranium in uranium dioxide powder and pellets — Iron(II) sulfate reduction/potassium dichromate oxidation titrimetric method,Dosage de l'uranium dans la poudre et les pastilles de dioxyde d'uranium — Méthode titrimétrique par réduction par le sulfate de fer (II) et oxydation par le dichromate de potassium,1996-06-20,1,['27.120.30'],ISO/TC 85/SC 5,9599,,"[34541,34540]","['en','fr']",7,

5445,IS,,ISO 999:1975,Documentation — Index of a publication,Documentation — Index d'une publication,1975-09-01,1,['01.140.40'],ISO/TC 46/SC 9,9599,,[5446],"['en','fr']",2,

17907,IS,,ISO 9994:1989,Lighters — Safety specification,Briquets — Spécifications de sécurité,1989-06-15,1,['65.160'],ISO/TMBG,9599,,[22744],"['en','fr']",11,

22744,IS,,ISO 9994:1995,Lighters — Safety specification,Briquets — Spécifications de sécurité,1995-12-27,2,['97.180'],ISO/TC 61,9599,[17907],[31754],"['en','fr']",14,<p>Establishes requirements for lighters to ensure a reasonable degree of safety for normal use or reasonably foreseeable misuse of such lighters.</p>

31754,IS,,ISO 9994:2002,Lighters — Safety specification,Briquets — Spécifications de sécurité,2002-03-14,3,['97.180'],ISO/TC 61,9599,[22744],[42889],"['en','fr']",23,

42889,IS,,ISO 9994:2005,Lighters — Safety specification,Briquets — Spécifications de sécurité,2005-09-01,4,['97.180'],ISO/TC 61/SC 4,9599,"[40915,36621,31754]",[64742],"['en','fr']",26,"<p>ISO 9994:2005 establishes requirements for lighters to ensure a reasonable degree of safety for normal use or reasonably foreseeable misuse of such lighters by users.</p><p>The safety specification given in this International Standard applies to all flame-producing products commonly known as cigarette lighters, cigar lighters and pipe lighters. It does not apply to matches, nor does it apply to other flame-producing products intended solely for igniting materials other than cigarettes, cigars, and pipes.</

45096,IS,Amd,ISO 9994:2005/Amd 1:2008,Lighters — Safety specification — Amendment 1: Clarification of structural requirements,Briquets — Spécifications de sécurité — Amendement 1: Précisions concernant les exigences structurelles,2008-01-31,4,['97.180'],ISO/TC 61,9599,,[64742],"['en','fr']",2,

17932,IS,,ISO 9997:1990,Dental cartridge syringes,Seringues à usage dentaire pour cartouches,1990-10-25,1,"['11.040.20','11.060.20']",ISO/TC 106/SC 4,9599,,[20416],"['en','fr']",4,

20416,IS,,ISO 9997:1999,Dental cartridge syringes,Seringues à usage dentaire pour cartouches,1999-12-16,2,"['11.040.25','11.060.20']",ISO/TC 106/SC 4,9599,[17932],[73465],"['en','fr']",6,

17933,IS,,ISO 9998:1991,Water quality — Practices for evaluating and controlling microbiological colony count media used in water quality tests,Qualité de l'eau — Techniques d'évaluation et de contrôle des milieux microbiologiques servant au comptage des colonies pour les essais d'évaluation de la qualité de l'eau,1991-10-17,1,['07.100.20'],ISO/TC 147/SC 4,9599,,[53610],"['en','fr']",22,"<p>Describes a method used for the comparison and evaluation of the same medium prepared from different lots of materials, and deals with the comparison and evaluation of different media which are used for the same purpose. Annexes A and B form an integral part of this Standard.</p>"

17934,IS,,ISO 9999:1992,Technical aids for disabled persons — Classification,Aides techniques pour personnes handicapées — Classification,1992-04-09,1,['11.180'],ISO/TC 173/SC 2,9599,,[23023],"['en','fr']",28,

23023,IS,,ISO 9999:1998,Technical aids for disabled persons — Classification,Aides techniques pour personnes atteintes d'un handicap — Classification,1998-04-02,2,['11.180.01'],ISO/TC 173/SC 2,9599,[17934],[33150],"['en','fr']",90,

33150,IS,,ISO 9999:2002,Technical aids for persons with disabilities — Classification and terminology,Aides techniques pour personnes atteintes d'incapacités — Classification et terminologie,2002-10-22,3,['11.180.01'],ISO/TC 173/SC 2,9599,[23023],[38894],"['en','fr']",104,

38894,IS,,ISO 9999:2007,Assistive products for persons with disability — Classification and terminology,Produits d'assistance pour personnes en situation de handicap — Classification et terminologie,2007-02-21,4,['11.180.01'],ISO/TC 173/SC 2,9599,[33150],[50982],"['en','fr']",86,"<p>ISO 9999:2007 establishes a classification of assistive products especially produced, or generally available, for persons with disability.</p><p>Assistive products used by a person with disability, but which require the assistance of another person for their operation, are included in the classification.</p><p>The following items are specifically excluded from ISO 9999:2007:</p><ul><li>items used for the installa

46565,IS,Cor,ISO 9999:2007/Cor 1:2007,Assistive products for persons with disability — Classification and terminology — Technical Corrigendum 1,Produits d'assistance pour personnes en situation de handicap — Classification et terminologie — Rectificatif technique 1,2007-08-06,4,['11.180.01'],ISO/TC 173/SC 2,9599,,[50982],"['en','fr']",1,

50982,IS,,ISO 9999:2011,Assistive products for persons with disability — Classification and terminology,Produits d'assistance pour personnes en situation de handicap — Classification et terminologie,2011-07-06,5,['11.180.01'],ISO/TC 173/SC 2,9599,"[38894,46565]",[60547],"['en','fr']",100,"<p>ISO 9999:2011 establishes a classification of assistive products, especially produced or generally available, for persons with disability.</p><p>Assistive products used by a person with disability, but which require the assistance of another person for their operation, are included in the classification.</p><p>The following items are specifically excluded from ISO 9999:2011: items used for the installati

60547,IS,,ISO 9999:2016,Assistive products for persons with disability — Classification and terminology,Produits d'assistance pour personnes en situation de handicap — Classification et terminologie,2016-10-07,6,['11.180.01'],ISO/TC 173/SC 2,9599,[50982],[72464],"['en','fr']",194,"<p>ISO 9999:2016 establishes a classification and terminology of assistive products, especially produced or generally available, for persons with disability.</p><p>Assistive products used by a person with disability, but which require the assistance of another person for their operation, are included in the classification.</p><p>The following items are specifically excluded from this International Standard:</p><p>-

54740,IS,,ISO/ASME 14414:2015,Pump system energy assessment,Évaluation énergétique des systèmes de pompage,2015-04-01,1,['23.080'],ISO/TC 115,9599,,[71534],"['en','fr']",61,"<p>ISO/ASME 14414:2015 sets the requirements for conducting and reporting the results of a pumping system energy assessment (hereafter referenced as 'assessment') that considers the entire pumping system, from energy inputs to the work performed as the result of these inputs.</p><p>The objective of a pumping system energy assessment is to determine the current energy consumption of an existing system and identify ways to improve system efficiency.</p><p>These requirements consist of</p><ul><li>organizing and conducting a

68822,IS,Amd,ISO/ASME 14414:2015/Amd 1:2016,Pump system energy assessment — Amendment 1,Évaluation énergétique des systèmes de pompage — Amendement 1,2016-03-22,1,['23.080'],ISO/TC 115,9599,,[71534],"['en','fr']",1,

33566,IS,,ISO/ASTM 51204:2002,Practice for dosimetry in gamma irradiation facilities for food processing,Pratique de la dosimétrie dans les installations de traitement des produits alimentaires par irradiation gamma,2002-04-18,1,"['17.240','67.020']",ISO/TC 85,9599,[28203],[39030],['en'],9,"<p>This practice outlines dosimetric procedures to be followed in irradiator characterization, process qualification, and routine processing of food with ionizing radiation from isotopic gamma sources to ensure that all the product has been treated within a predetermined range of absorbed dose. Other procedures related to irradiator characterization, process qualification, and routine processing that may

33568,IS,,ISO/ASTM 51205:2002,Practice for use of a ceric-cerous sulfate dosimetry system,Pratique de l'utilisation d'un système dosimétrique au sulfate cérique-céreux,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28204],[44181],['en'],11,"<p>ISO/ASTM 51205 covers the preparation, testing and procedure for using the ceric-cerous sulfate dosimetry system to measure absorbed doses in water when exposed to ionizing radiation. The system consists of a dosimeter and appropriate analytical instrumentation. For simplicity, the system is referred to as the ceric-cerous system. It is classified as a reference standard dosimetry system. Ceric-cerous dosimeters are also used as transfer standard dosimeters o

44181,IS,,ISO/ASTM 51205:2009,Practice for use of a ceric-cerous sulfate dosimetry system,Pratique de l'utilisation d'un système dosimétrique au sulfate cérique-céreux,2009-07-07,2,['17.240'],ISO/TC 85,9599,[33568],[71479],['en'],11,"<p>ISO 51205:2009 applies to the procedures for preparation, testing, and using the ceric-cerous sulfate dosimetry system to determine absorbed dose (in terms of absorbed dose to water) in materials irradiated by photons (gamma radiation or X-radiation/bremsstrahlung) or high-energy electrons. The system consists of a dosimeter and appropriate analytical instrumentation.</p><p>The system is classified as a reference–standard dosimetry system but can also be used

33569,IS,,ISO/ASTM 51261:2002,Guide for selection and calibration of dosimetry systems for radiation processing,Guide de choix et d'étalonnage des appareils de mesure dosimétrique pour le traitement par irradiation,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28202],[60211],['en'],19,"<p>ISO/ASTM 51261 covers the basis for selecting and calibrating dosimetry systems used to measure absorbed doses in gamma-ray or X-ray fields and in electron beams used for radiation processing. It discusses the types of dosimetry systems that may be used during calibration or on a routine basis as part of quality assurance in commercial radiation processing of products. ISO/ASTM 51261 also discusses interpretation

33570,IS,,ISO/ASTM 51275:2002,Practice for use of a radiochromic film dosimetry system,Pratique de l'utilisation d'un système dosimétrique à film radiochromique,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28205],[40158],['en'],5,"<p>ISO/ASTM 51275 covers the handling, testing and procedure for using a radiochromic film dosimetry system to measure absorbed doses in materials irradiated by photons or electrons in terms of absorbed dose in water. This practice applies to radiochromic film dosimeters that can be used within part or all of the specified ranges as follows:</p><p>absorbed dose range 1 Gy to 100 kGy;</p><p>absorbed dose rate 1 times 10^-2 Gy/s to 1 times 10 ¹³ Gy/s;

40158,IS,,ISO/ASTM 51275:2004,Practice for use of a radiochromic film dosimetry system,Pratique de l'utilisation d'un système dosimétrique à film radiochromique,2004-07-08,2,['17.240'],ISO/TC 85,9599,[33570],[62954],['en'],5,"<p>ISO/ASTM 51275:2004 covers the procedures for handling, testing and using a radiochromic film dosimetry system to measure absorbed dose in materials irradiated by photons or electrons in terms of absorbed dose in water.</p>"

33554,IS,,ISO/ASTM 51276:2002,Practice for use of a polymethylmethacrylate dosimetry system,Pratique de l'utilisation d'un système dosimétrique au polyméthylméthacrylate,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28206],[37109],['en'],7,"<p>ISO/ASTM 51276 covers procedures for using hermetically-sealed polymethylmethacrylate (PMMA) dosimeters for measuring absorbed doses in materials irradiated by photons or electrons in terms of absorbed dose in water.</p><p>It also covers systems that permit absorbed dose measurements under the following conditions:</p><p> the absorbed dose range is 0,1 kGy to 100 kGy.</p><p> the absorbed dose rate is 1 times 10^-2 Gy·s ^-1to 1 times 10<s

57398,IS,,ISO/ASTM 51276:2012,Practice for use of a polymethylmethacrylate dosimetry system,Pratique de l'utilisation d'un système dosimétrique au polyméthylméthacrylate,2012-10-05,3,['17.240'],ISO/TC 85,9599,[37109],[78276],['en'],6,"<p>ISO/ASTM 51276:2012 provides recommendations for properly implementing dosimetry in radiation processing.</p><p>ISO/ASTM 51276:2012 specifies a practice for using polymethylmethacrylate (PMMA) dosimetry systems to measure absorbed dose in materials irradiated by photons or electrons in terms of absorbed dose to water. The PMMA dosimetry system is classified as a routine dosimetry system. The PMMA dosimeter is classified as a Type II dosimeter on the basis of

33571,IS,,ISO/ASTM 51310:2002,Practice for use of a radiochromic optical waveguide dosimetry system,Pratique de l'utilisation d'un système dosimétrique à guide d'ondes optiques radiochromiques,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28207],[40159],['en'],5,"<p>ISO/ASTM 51310 covers the handling, testing and procedure for using a radiochromic optical waveguide dosimetry system to measure absorbed doses in materials irradiated by photons in terms of absorbed dose in water. This practice applies to radiochromic optical waveguide dosimeters that can be used within part or all of the specified ranges as follows:</p><p>absorbed dose range from 1 Gy to 10 000 Gy for photons;</p><p>absorbed dose rat

40159,IS,,ISO/ASTM 51310:2004,Practice for use of a radiochromic optical waveguide dosimetry system,Pratique de l'utilisation d'un système dosimétrique à guide d'ondes optiques radiochromiques,2004-07-08,2,['17.240'],ISO/TC 85,9599,[33571],[82762],['en'],5,"<p>ISO 51310:2004 covers the procedures for handling, testing and using a radiochromic optical waveguide dosimetry system to measure absorbed dose in materials irradiated by photons in terms of absorbed dose in water.</p>"

33555,IS,,ISO/ASTM 51400:2002,Practice for characterization and performance of a high-dose radiation dosimetry calibration laboratory,Pratique de caractérisation et d'exploitation d'un laboratoire d'étalonnage de dosimétrie d'irradiations à hautes doses,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28208],[38103],['en'],10,"<p>ISO/ASTM 15400 describes the characterization and performance criteria to be met by a high-dose radiation dosimetry calibration laboratory. By meeting these criteria, the laboratory may be accredited by a recognized accreditation organization. Adherence to these criteria will ensure high standards of performance and instill confidence that the accredited laboratory is compet

33556,IS,,ISO/ASTM 51401:2002,Practice for use of a dichromate dosimetry system,Pratique de l'utilisation d'un système de mesure dosimétrique au dichromate,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28209],[38106],['en'],7,"<p>ISO/ASTM 51401 covers the preparation, testing, and procedure for using the acidic aqueous silver dichromate dosimetry system to measure absorbed doses in water when exposed to ionizing radiation. The system consists of a dosimeter and appropriate analytical instrumentation. For simplicity, the system is referred to as the dichromate system and is classified as a reference standard dosimetry system.</p><p>This International Standard describes the spectrophotometric analys

38106,IS,,ISO/ASTM 51401:2003,Practice for use of a dichromate dosimetry system,Pratique de l'utilisation d'un système dosimétrique au dichromate,2003-08-18,2,['17.240'],ISO/TC 85,9599,[33556],[62951],['en'],6,"<p>ISO/ASTM 51401:2003 covers the preparation, testing, and procedure for using the acidic aqueous silver dichromate dosimetry system to measure absorbed dose in water when exposed to ionizing radiation. The system consists of a dosimeter and appropriate analytical instrumentation. For simplicity, the system will be referred to as the dichromate system. It is classified as a reference standard dosimetry system.</p><p>ISO/ASTM 51401:2003 describes the spectrophotometric analysis proced

33572,IS,,ISO/ASTM 51431:2002,Practice for dosimetry in electron and bremsstrahlung irradiation facilities for food processing,Pratique de la dosimétrie dans les installations de traitement des produits alimentaires irradiés par électrons et Bremsstrahlung,2002-04-18,1,"['17.240','67.020']",ISO/TC 85,9599,[28210],[39913],['en'],10,"<p>ISO/ASTM 51431 describes dosimetric procedures to be followed in facility characterization, process qualification and routine processing for electron beam and bremsstrahlung irradiation facilities for food processing in order to ensure that the product receives an acceptable range of absorbed doses. Other procedures related to facility characterization, process

33573,IS,,ISO/ASTM 51538:2002,Practice for use of the ethanol-chlorobenzene dosimetry system,Pratique de l'utilisation d'un système dosimétrique à l'éthanol chlorobenzène,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28211],[44183],['en'],10,"<p>ISO/ASTM 51538 covers the preparation, handling, testing and procedure for using the ethanol-chlorobenzene dosimetry system to measure absorbed doses in materials irradiated by photons and electrons in terms of absorbed dose in water. The system consists of a dosimeter and appropriate analytical instrumentation. This practice describes the titration analysis as a standard readout procedure for the ECB dosimeter and applies only to gamma rays, X rays and hi

44183,IS,,ISO/ASTM 51538:2009,Practice for use of the ethanol-chlorobenzene dosimetry system,Pratique de l'utilisation d'un système dosimétrique à l'éthanol chlorobenzène,2009-07-07,2,['17.240'],ISO/TC 85,9599,[33573],[72759],['en'],11,"<p>ISO 51538:2009 covers the procedure for preparation, handling, testing, and use of the ethanol-chlorobenzene (ECB) dosimetry system to determine absorbed dose (in terms of absorbed dose to water) in materials irradiated by photons (gamma radiation or X-radiation/bremsstrahlung) or high energy electrons. The system consists of a dosimeter and appropriate analytical instrumentation. It is classified as a reference-standard dosimetry system and is also used a

33574,IS,,ISO/ASTM 51539:2002,Guide for use of radiation-sensitive indicators,Guide pour l'utilisation d'indicateurs sensibles aux rayonnements,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28212],[40927],['en'],2,"<p>ISO/ASTM 51539 covers the use of radiation-sensitive indicators in radiation processing. These indicators may be labels, papers, inks or packaging materials which undergo a colour change or become coloured when exposed to ionizing radiation.</p><p>The purpose of these indicators is to determine visually whether or not a product has been irradiated, rather than to measure different dose levels.</p>"

40927,IS,,ISO/ASTM 51539:2005,Guide for use of radiation-sensitive indicators,Guide pour l'utilisation d'indicateurs sensibles aux rayonnements,2005-07-22,2,['17.240'],ISO/TC 85,9599,[33574],[63642],['en'],3,"<p>ISO/ASTM 51539:2005 covers procedures for using radiationsensitive indicators in radiation processing. These indicators may be labels, papers, inks or packaging materials which undergo a visual change when exposed to ionizing radiation.</p>"

63642,IS,,ISO/ASTM 51539:2013,Guide for use of radiation-sensitive indicators,Guide pour l'utilisation d'indicateurs sensibles aux rayonnements,2013-09-27,3,['17.240'],ISO/TC 85,9599,[40927],[83489],['en'],3,"<p>ISO/ASTM 51539:2013 covers procedures for using radiation-sensitive indicators in radiation processing. These indicators may be labels, papers, inks or packaging materials which undergo a visual change when exposed to ionizing radiation. The purpose for using indicators is to determine visually whether or not a product has been irradiated, rather than to measure different dose levels. </p>"

33575,IS,,ISO/ASTM 51540:2002,Practice for use of a radiochromic liquid dosimetry system,Pratique de l'utilisation d'un système dosimétrique radiochromique liquide,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28213],[40160],['en'],7,"<p>ISO/ASTM 51540 covers the preparation, handling, testing and procedure for using radiochromic liquid dosimetry systems of radiochromic dye solutions held in sealed or capped containers (e.g., ampoules, vials). It also covers the use of spectrophotometric or photometric read-out equipment for measuring absorbed doses in materials irradiated by photons and electrons.</p><p>This practice applies to radiochromic liquid dosimeter solutions that can be used within part

33576,IS,,ISO/ASTM 51607:2002,Practice for use of the alanine-EPR dosimetriy system,Pratique de l'utilisation d'un système dosimétrique à l'alanine utilisant la résonance paramagnétique électronique,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28214],[39026],['en'],7,"<p>ISO/ASTM 51607 covers materials description, dosimeter preparation, instrumentation and procedures for using the alanine-EPR dosimetry system for measuring the absorbed dose in materials irradiated with photons and electrons. The system is based on electron paramagnetic resonance (EPR) spectroscopy of free radicals derived from the amino acid alanine. It is classified as a reference standard dosimetry system.</p><p>This Internati

39026,IS,,ISO/ASTM 51607:2004,Practice for use of the alanine-EPR dosimetry system,Pratique de l'utilisation d'un système dosimétrique à l'alanine utilisant la résonance paramagnétique électronique,2004-10-25,2,['17.240'],ISO/TC 85,9599,[33576],[62955],['en'],6,"<p>ISO/ASTM 51607:2004 covers materials description, dosimeter preparation, instrumentation, and procedures for using the alanine-EPR dosimetry system for measuring the absorbed dose in the photon and electron irradiation processing of materials. The system is based on electron paramagnetic resonance (EPR) spectroscopy of free radicals derived from the amino acid alanine. ISO/ASTM 51607:2004 covers alanine-EPR dosimetry systems for d

33577,IS,,ISO/ASTM 51608:2002,Practice for dosimetry in an X-ray (bremsstrahlung) facility for radiation processing,Pratique de la dosimétrie dans une installation de traitement par des rayons X (Bremsstrahlung),2002-04-18,1,"['17.240','67.020']",ISO/TC 85,9599,[28215],[39914],['en'],11,"<p>ISO/ASTM 15608 covers dosimetric procedures to be followed in facility characterization, process qualification and routine processing using X-rays (bremsstrahlung) to ensure that the entire product has been treated within an acceptable range of absorbed doses. Other procedures related to facility characterization, process qualification, and routine processing that may influence absorbed doses in the produ

39914,IS,,ISO/ASTM 51608:2005,Practice for dosimetry in an X-ray (bremsstrahlung) facility for radiation processing,Pratique de la dosimétrie dans une installation de traitement par des rayons X (Bremsstrahlung),2005-06-01,2,['17.240'],ISO/TC 85,9599,[33577],[66727],['en'],17,"<p>ISO/ASTM 51608:2005 outlines the installation qualification program for an X-ray (bremsstrahlung) irradiator and the dosimetric procedures to be followed during operational qualification, performance qualification and routine processing to ensure that the entire product has been treated within a predetermined range of absorbed dose. Other procedures related to operational qualification, performance qualification and

33557,IS,,ISO/ASTM 51631:2002,Practice for use of calorimetric dosimetry systems for electron beam dose measurements and dosimeter calibrations,Pratique de l'utilisation des systèmes dosimétriques calorimétriques pour des mesures de dose délivrée par un faisceau d'électrons et pour l'étalonnage de dosimètres,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28216],[38104],['en'],9,"<p>ISO/ASTM 51631 covers the preparation and use of semi-adiabatic calorimeters for measurement of absorbed doses in graphite, water or polystyrene when irradiated with electrons. The calorimeters are either transported by a conveyor past a scanned electron beam or are stationary in a broadened beam. It also covers the use

38104,IS,,ISO/ASTM 51631:2003,Practice for use of calorimetric dosimetry systems for electron beam dose measurements and dosimeter calibrations,Pratique de l'utilisation des systèmes dosimétriques calorimétriques pour des mesures de dose délivrée par un faisceau d'électrons et pour l'étalonnage de dosimètres,2003-08-18,2,['17.240'],ISO/TC 85,9599,[33557],[60212],['en'],8,"<p>ISO/ASTM 51631:2003 covers the preparation and use of semi-adiabatic calorimeters for measurement of absorbed dose and routine dosimeter calibration when irradiated with electrons for radiation processing applications. The calorimeters are either transported by a conveyor past a scanned electron beam or are stationary in

60212,IS,,ISO/ASTM 51631:2013,Practice for use of calorimetric dosimetry systems for electron beam dose measurements and dosimetery system calibrations,Pratique de l'utilisation des systèmes dosimétriques calorimétriques pour pour des mesures de dose délivrée par un faisceau d'électrons et pour l'étalonnage de dosimètres,2013-03-22,3,['17.240'],ISO/TC 85,9599,[38104],[79634],['en'],9,<p>ISO/ASTM 51631:2013 covers the preparation and use of semiadiabatic calorimetric dosimetry systems for measurement of absorbed dose and for calibration of routine dosimetry systems when irradiated with electrons for radiation processing applications. The calorimeters are either transported by a conveyor past

33558,IS,,ISO/ASTM 51649:2002,Practice for dosimetry in an electron-beam facility for radiation processing at energies between 300 keV and 25 MeV,Pratique de la dosimétrie dans une installation de traitement par irradiation utilisant un faisceau d'électrons d'énergies comprises entre 300 keV et 25 MeV,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28217],[39027],['en'],20,"<p>ISO/ASTM 51649 covers dosimetric procedures to be followed in facility characterization, process qualification and routine processing using electron beam radiation in order to ensure that the entire product has been treated with an acceptable range of absorbed doses. Other procedures related to facility characterization (inclu

39027,IS,,ISO/ASTM 51649:2005,Practice for dosimetry in an electron beam facility for radiation processing at energies between 300 keV and 25 MeV,Pratique de la dosimétrie dans une installation de traitement par irradiation utilisant un faisceau d'électrons d'énergies comprises entre 300 keV et 25 MeV,2005-07-20,2,['17.240'],ISO/TC 85,9599,[33558],[66728],['en'],30,"<p>ISO/ASTM 51649:2005 covers dosimetric procedures to be followed in Installation Qualification, Operational Qualification and Performance Qualifications (IQ, OQ, PQ), and routine processing at electron beam facilities to ensure that the product has been treated with an acceptable range of absorbed doses. Other procedures relate

33578,IS,,ISO/ASTM 51650:2002,Practice for use of a cellulose triacetate dosimetry system,Pratique de l'utilisation d'un système dosimétrique au triacétate de cellulose,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28218],[39916],['en'],8,"<p>ISO 51650 covers the preparation, handling, testing and procedures for the use of cellulose acetate dosimetry systems, and the spectrometric, densitometric or photometric read-out equipment for measuring absorbed doses in materials irradiated by photons and electrons in terms of absorbed dose in water.</p><p>Cellulose acetate dosimeter refers to untinted and tinted cellulose triacetate (CTA) or cellulose diacetate (CDA) film dosimeter.</p><p>This practice app

39916,IS,,ISO/ASTM 51650:2005,Practice for use of a cellulose triacetate dosimetry system,Pratique de l'utilisation d'un système dosimétrique au triacétate de cellulose,2005-07-22,2,['17.240'],ISO/TC 85,9599,[33578],[62956],['en'],7,<p>ISO/ASTM 51650:2005 covers procedures for using the cellulose triacetate (CTA) dosimetry system for measuring absorbed dose and dose profile in materials irradiated by electrons and photons in terms of absorbed dose to water. The CTA dosimeter is a routine dosimeter especially useful for measurement of dose distribution.</p>

33559,IS,,ISO/ASTM 51702:2002,Practice for dosimetry in a gamma irradiation facility for radiation processing,Pratique de la dosimétrie dans une installation de traitement par irradiation gamma,2002-04-18,1,['17.240'],ISO/TC 85,9599,[28219],[39029],['en'],7,"<p>ISO/ASTM 15702 outlines dosimetric procedures to be followed in irradiator characterization, process qualification, and routine processing in a gamma irradiation facility. These procedures ensure that all product processed with ionizing radiation from isotopic gamma sources receive absorbed doses within a predetermined range. Other procedures related to irradiator characterization, process qualification and routine processing that may

39029,IS,,ISO/ASTM 51702:2004,Practice for dosimetry in a gamma irradiation facility for radiation processing,Pratique de la dosimétrie dans les installations de traitement par irradiation gamma,2004-10-25,2,['17.240'],ISO/TC 85,9599,[33559],[61086],['en'],10,"<p>ISO/ASTM 51702:2004 outlines the installation qualification program for an irradiator and the dosimetric procedures to be followed during operational qualification, performance qualification, and routine processing in facilities that process product with ionizing radiation from radionuclide gamma sources to ensure that product has been treated within a predetermined range of absorbed dose. Other procedures related to installation qu