Withdrawn and superseded ISO standards — page 187 of 246

23258,IS,,ISO 9712:1999,Non-destructive testing — Qualification and certification of personnel,Essais non destructifs — Qualification et certification du personnel,1999-05-06,2,"['03.100.30','19.100']",ISO/TC 135/SC 7,9599,[17570],[36092],"['en','fr']",22,

36092,IS,,ISO 9712:2005,Non-destructive testing — Qualification and certification of personnel,Essais non destructifs — Qualification et certification du personnel,2005-02-17,3,"['03.100.30','19.100']",ISO/TC 135/SC 7,9599,[23258],[57037],['en'],25,<p>ISO 9712:2005 specifies the qualification and certification of personnel involved in non-destructive testing (NDT). It is applicable to proficiency in one or more of the following methods: acoustic emission testing; eddy current testing; infrared thermographic testing; leak testing (hydraulic pressure tests excluded); magnetic particle testing; penetrant testing; radiographic testing; strain testing; ultrasonic testing; visual testing (direct u

44970,IS,Cor,ISO 9712:2005/Cor 1:2006,Non-destructive testing — Qualification and certification of personnel — Technical Corrigendum 1,Essais non destructifs — Qualification et certification du personnel — Rectificatif technique 1,2006-10-30,3,"['03.100.30','19.100']",ISO/TC 135/SC 7,9599,,[57037],['en'],1,

57037,IS,,ISO 9712:2012,Non-destructive testing — Qualification and certification of NDT personnel,Essais non destructifs — Qualification et certification du personnel END,2012-06-14,4,"['03.100.30','19.100']",ISO/TC 135/SC 7,9599,"[44970,36092]",[75614],"['en','fr','ru']",31,"<p>This International Standard specifies requirements for principles for the qualification and certification of personnel who perform industrial non-destructive testing (NDT).</p><p>The system specified in this International Standard can also apply to other NDT methods or to new techniques within an established NDT method, provided a comprehensive scheme of certification exists and the method or technique is covered by

17571,IS,,ISO 9713:1990,Neurosurgical implants — Self-closing intracranial aneurysm clips,Implants neurochirurgicaux — Clips intracraniens pour anévrisme à auto-fermeture,1990-12-13,1,['11.040.40'],ISO/TC 150,9599,,[21488],"['en','fr']",6,<p>Intended to insure that appropriate and comparable information is supplied for each clip in order to facilitate the choice of the correct clip by the surgeon. Specifies the requirements for clips intended for permanent intracardial implantation.</p>

21488,IS,,ISO 9713:2002,Neurosurgical implants — Self-closing intracranial aneurysm clips,Implants neurochirurgicaux — Clips intracrâniens pour anévrisme à autofermeture,2002-09-05,2,['11.040.40'],ISO/TC 150,9599,[17571],[75217],"['en','fr']",7,"<p>ISO 9713:2002 describes characteristics of self-closing aneurysm clips intended for permanent intracranial implantation and specifies requirements for marking, packaging, sterilization and for labelling and accompanying documentation. In addition it gives a method for the measurement of closing force.</p><p>ISO 9713:2002 is not applicable to malleable clips, or clips intended to be used during the course of surgery and removed before wound closure

17572,IS,,ISO 9714-1:1991,"Orthopaedic drilling instruments — Part 1: Drill bits, taps and countersink cutters","Instruments orthopédiques — Instruments de forage — Partie 1: Tarauds, forets et fraises à lamer",1991-03-14,1,['11.040.40'],ISO/TC 150/SC 5,9599,,[55438],"['en','fr']",5,"<p>Part 1 of ISO 9714 specifies materials and mechanical properties, dimensions and marking requirements for the mentioned instruments made of stainless steel for use in orthopaedic surgery with bone screws as specified in ISO 5835. Instruments made of other materials and coatings may be included at a later revision. The interrelationship of International Standards dealing with bone screws and relevant tools is

17575,IS,,ISO 9717:1990,Phosphate conversion coatings for metals — Method of specifying requirements,Couches de conversion au phosphate sur métaux — Méthode de spécification des caractéristiques,1990-04-26,1,['25.220.20'],ISO/TC 107/SC 8,9599,,[53534],"['en','fr']",15,

53534,IS,,ISO 9717:2010,Metallic and other inorganic coatings — Phosphate conversion coating of metals,Revêtements métalliques et autres revêtements inorganiques — Couches de conversion au phosphate sur métaux,2010-11-30,2,['25.220.20'],ISO/TC 107/SC 8,9599,[17575],[68517],"['en','fr']",23,"<p>ISO 9717:2010 specifies requirements for the processing of ferrous metals, aluminium, zinc, cadmium and their alloys to produce coatings consisting essentially of inorganic phosphates, which are intended to be used in conjunction with supplementary treatments for the protection of the basis metal against corrosion and to provide anti-wear properties to sliding surfaces, adhesion to organic finishes and

68517,IS,,ISO 9717:2017,Metallic and other inorganic coatings — Phosphate conversion coating of metals,Revêtements métalliques et autres revêtements inorganiques — Couches de conversion au phosphate sur métaux,2017-09-14,3,['25.220.20'],ISO/TC 107/SC 8,9599,[53534],[83693],"['en','fr']",13,"<p>ISO 9717:2017 specifies a process for the confirmation of requirements for phosphate coatings which are usually destined for application on ferrous materials, zinc, cadmium and their alloys (see Annex B).</p>"

17576,IS,,ISO 9718:1991,Photography — Processed vesicular photographic film — Specifications for stability,Photographie — Film photographique vésiculaire traité — Prescriptions pour assurer la stabilité,1991-02-14,1,['37.040.20'],ISO/TC 42,9599,,[23408],['en'],15,

23408,IS,,ISO 9718:1995,Photography — Processed vesicular photographic film — Specifications for stability,Photographie — Film photographique vésiculaire traité — Spécifications relatives à la stabilité,1995-11-02,2,['37.040.20'],ISO/TC 42,9599,[17576],[31936],['en'],20,<p>Establishes specifications for the stability of polyester-based heat-processed vesicular safety film. Replaces the first edition which has been technically revised.</p>

5407,IS,,ISO 972:1985,"Chillies and capsicums, whole or ground (powdered) — Specification",Piments dits 'Piments enragés' et piments forts entiers ou en poudre — Spécifications,1985-07-04,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[5408],"['en','fr']",5,

17580,IS,,ISO 9722:1992,Nickel and nickel alloys — Composition and forms of wrought products,Nickel et alliages de nickel — Composition chimique et formes des produits corroyés,1992-11-12,1,['77.150.40'],ISO/TC 155,9599,,[29811],"['en','fr']",8,<p>Lists the chemical composition and density of wrought nickel and nickel alloys and commercially available wrought products. Annex A contains a list of ISO methods of analysis. The definitions for nickel and nickel alloys in ISO 6372-1 and for wrought products in ISO 6372-3 apply.</p>

17581,IS,,ISO 9723:1992,Nickel and nickel alloy bars,Barres en nickel et alliages de nickel,1992-11-25,1,['77.150.40'],ISO/TC 155,9599,,[29812],"['en','fr']",14,"<p>Specifies requirements (composition, temper, tensile properties, heat treatment, grain size, dimensional tolerances, surface condition, finish) and associated test procedures for cold-worked bars up to and including 65 mm diameter or width across flats and hot-worked bars up to and including 315 mm diameter or width across flats. Annex A gives a list of ISO methods of analysis.</p>"

17582,IS,,ISO 9724:1992,Nickel and nickel alloy wire and drawing stock,Fil et fil-machine en nickel et alliages de nickel,1992-11-25,1,['77.150.40'],ISO/TC 155,9599,,[29813],"['en','fr']",10,"<p>Specifies requirements (composition, tensile properties, surface quality, dimensional tolerances) and associated test procedures for wire up to and including 10 mm and for drawing stock, both für general purposes. Annex A gives a list of ISO methods of analysis.</p>"

17583,IS,,ISO 9725:1992,Nickel and nickel alloy forgings,Pièces forgées en nickel et alliages de nickel,1992-11-25,1,['77.150.40'],ISO/TC 155,9599,,"[69353,29814]","['en','fr']",11,"<p>Specifies ordering information, requirements for forgings heat treated by the manufacturer and forgings to be heat treated by the purchaser, sampling, test procedures, marking, purchaser or third party inspection, declaration of conformity. Annex A gives a list of ISO methods of analysis.</p>"

17586,IS,,ISO 9727:1991,Cylindrical stoppers of natural cork — Physical tests — Reference methods,Bouchons cylindriques en liège naturel — Essais physiques — Méthodes de référence,1991-02-28,1,"['79.100','55.100']",ISO/TC 87,9599,,"[36668,36660,36662,36666,36663,28111,36667,36664]","['en','fr']",9,"<p>Specifies the reference methods for determining the following characteristics of theses stoppers: dimensions; deviations from parallelism of bases and from perpendicularity of sides and bases; apparent density; moisture content,; behaviour under compression; extraction and penetration strengths; absorption; and capillarity. Sealing behaviour will be covered later. Contains sampling, reagents, a

5409,IS,,ISO 973:1980,"Spices and condiments — Pimento (allspice), whole or ground — Specification","Épices — Piment, type Jamaïque, entier ou en poudre — Spécifications",1980-09-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[26523],"['en','fr']",4,

26523,IS,,ISO 973:1999,"Pimento (allspice) [Pimenta dioica (L.) Merr.], whole or ground — Specification","Piment type Jamaïque [Pimenta dioica (L.) Merr.], entier ou en poudre — Spécifications",1999-10-14,2,['67.220.10'],ISO/TC 34/SC 7,9599,[5409],[90588],"['en','fr']",4,"<p>This International Standard specifies requirements for pimento or allspice [Pimenta dioica (L.) Merr.], whole or</p><p>ground.</p><p>Recommendations relating to storage and transport conditions are given in annex A.</p>"

28131,IS,,ISO 9735-1:1998,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 1: Syntax rules common to all parts, together with syntax service directories for each of the parts","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4) — Partie 1: Règles de syntaxe communes à l'ensemble des parties, accompagnées des répertoires de service syntaxiques associés à chacune d'elles",1998-10-15,1,['35.240.63'],ISO/TC 154,9599,"[30341,17592,17593]",[35032],"['en','fr']",65,

31206,IS,Cor,ISO 9735-1:1998/Cor 1:1998,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 1: Syntax rules common to all parts, together with syntax service directories for each of the parts — Technical Corrigendum 1","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4) — Partie 1: Règles de syntaxe communes à l'ensemble des parties, accompagnées des répertoires de service syntaxiques associés à chacune d'elles — Rectificatif technique 1",1998-12-20,1,['35.240.63'],ISO/TC 154,

35041,IS,,ISO 9735-10:2002,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 1) — Part 10: Syntax service directories","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4, numéro d'édition de syntaxe: 1) — Partie 10: Annuaires de syntaxe",2002-08-01,1,['35.240.63'],ISO/TC 154,9599,,[61434],['en'],110,<p>This part of ISO 9735 specifies the syntax service directories of all parts of the ISO 9735 series.</p>

61434,IS,,ISO 9735-10:2014,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4, Syntax release number: 2) — Part 10: Syntax service directories","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4, numéro d'édition de syntaxe: 2) — Partie 10: Annuaires de syntaxe",2014-12-16,2,['35.240.63'],ISO/TC 154,9599,[35041],[82813],"['en','ru']",112,<p>ISO 9735-10:2014 specifies the syntax service directories of all parts of ISO 9735.</p>

17592,IS,,ISO 9735:1988,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules","Échange de données informatisées pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application",1988-07-14,1,['35.240.63'],ISO/TC 154,9599,,"[28131,28915,28132,30034,28916,28133,30035,29066,28134,80091]",['en'],19,"<p>La présente Norme internationale définit les règles syntaxiques pour la préparation des messages destinés à être échangés entre les intervenants dans les domaines de l'administration, du commerce et du transport. <br/> <br/>NOTE -- Pour les utilisateurs de la présente Norme internationale, il c

17593,IS,Amd,ISO 9735:1988/Amd 1:1992,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules — Amendment 1","Échange de données informatisées pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application — Amendement 1",1992-12-03,1,['35.240.63'],ISO/TC 154,9599,,"[28131,28915,30034,28132,28916,29066,30035,28133,28134,80091]","['en','fr']",5,

28132,IS,,ISO 9735-2:1998,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 2: Syntax rules specific to batch EDI","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4) — Partie 2: Règles de syntaxe spécifiques à l'EDI par lots",1998-10-15,1,['35.240.63'],ISO/TC 154,9599,"[17592,17593]",[35033],"['en','fr']",4,

28133,IS,,ISO 9735-3:1998,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 3: Syntax rules specific to interactive EDI","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4) — Partie 3: Règles de syntaxe spécifiques à l'EDI interactif",1998-10-15,1,['35.240.63'],ISO/TC 154,9599,"[17592,17593]",[35034],"['en','fr']",21,

30034,IS,,ISO 9735-4:1998,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 4: Syntax and service report message for batch EDI (message type — CONTRL)","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4) — Partie 4: Message Compte rendu syntaxique et de service pour l'EDI par lots (type de message CONTRL)",1998-12-20,1,['35.240.63'],ISO/TC 154,9599,"[17592,17593]",[35035],"['en','fr']",10,

28915,IS,,ISO 9735-5:1999,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 5: Security rules for batch EDI (authenticity, integrity and non-repudiation of origin)","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (Numéro de version de syntaxe: 4) — Partie 5: Règles de sécurité pour EDI par lots (authenticité, intégrité et non-répudiation de l'origine)",1999-03-25,1,['35.240.63'],ISO/TC 154,9599,"[17592,17593]",[35036],"['en','fr']",50,

28916,IS,,ISO 9735-6:1999,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 6: Secure authentication and acknowledgement message (message type - AUTACK)","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4) — Partie 6: Message sécurisé Authentification et accusé de réception (type de message AUTACK)",1999-03-25,1,['35.240.63'],ISO/TC 154,9599,"[17592,17593]",[35037],"['en','fr']",30,

30035,IS,,ISO 9735-7:1999,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 7: Security rules for batch EDI (confidentiality)","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (Numéro de version de syntaxe: 4) — Partie 7: Règles de sécurité pour le lot EDI (confidentialité)",1999-08-19,1,['35.240.63'],ISO/TC 154,9599,"[17592,17593]",[35038],"['en','fr']",24,

28134,IS,,ISO 9735-8:1998,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 8: Associated data in EDI","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4) — Partie 8: Données associées en EDI",1998-10-08,1,['35.240.63'],ISO/TC 154,9599,"[17592,17593]",[35039],"['en','fr']",8,

29066,IS,,ISO 9735-9:1999,"Electronic data interchange for administration, commerce and transport (EDIFACT) — Application level syntax rules (Syntax version number: 4) — Part 9: Security key and certificate management message (message type- KEYMAN)","Échange de données informatisé pour l'administration, le commerce et le transport (EDIFACT) — Règles de syntaxe au niveau de l'application (numéro de version de syntaxe: 4) — Partie 9: Message Gestion de clés et de certificats de sécurité (type de message KEYMAN)",1999-03-25,1,['35.240.63'],ISO/TC 154,9599,"[17592,17593]",[35040],"['en','fr']",28,

5410,IS,,ISO 974:1980,Plastics — Determination of the brittleness temperature by impact,Plastiques — Détermination de la température de fragilité au choc,1980-06-01,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[28169],"['en','fr']",7,

5411,IS,,ISO 975:1975,Brown coals and lignites — Determination of yield of benzene-soluble extract,Charbons bruns et lignites — Détermination du rendement en extrait de benzène soluble,1975-11-01,1,['73.040'],ISO/TC 27,9599,,"[20409,5412]","['en','fr']",3,

5412,IS,,ISO 975:1985,Brown coals and lignites — Determination of yield of toluene-soluble extract,Charbons bruns et lignites — Détermination du rendement en extrait de toluène soluble,1985-12-12,2,['73.040'],ISO/TC 27,9599,[5411],[20409],"['en','fr']",3,

20409,IS,,ISO 975:2000,Brown coals and lignites — Determination of yield of benzene-soluble extract — Semi-automatic method,Charbons bruns et lignites — Détermination du rendement en extrait de benzène soluble — Méthode semi-automatique,2000-10-12,3,['73.040'],ISO/TC 27/SC 5,9599,"[5411,5412]",[63042],['en'],4,

63042,IS,,ISO 975:2013,Brown coals and lignites — Determination of yield of benzene-soluble extract — Semi-automatic method,Charbons bruns et lignites — Détermination du rendement en extrait de benzène soluble — Méthode semi-automatique,2013-05-06,4,['73.040'],ISO/TC 27/SC 5,9599,[20409],[79741],"['en','fr']",4,<p>ISO 975:2013 specifies a semi-automatic method for determination of the yield of benzene-soluble extract in brown coals and lignites.</p>

5413,IS,,ISO 976:1977,Rubber latices — Determination of pH,Latex de caoutchouc — Détermination du pH,1977-05-01,1,['83.040.10'],ISO/TC 45,9599,,[5414],['en'],2,

5414,IS,,ISO 976:1986,Rubber latices — Determination of pH,Latex de caoutchouc — Détermination du pH,1986-07-10,2,['83.040.10'],ISO/TC 45/SC 3,9599,[5413],[20182],"['en','fr']",2,

20182,IS,,ISO 976:1996,Rubber and plastics — Polymer dispersions and rubber latices — Determination of pH,Caoutchouc et plastiques — Dispersions de polymères et latex de caoutchouc — Détermination du pH,1996-06-13,3,['83.040.10'],ISO/TC 45/SC 3,9599,"[5414,5691]",[60896],"['en','fr']",6,"<p>Gives a method for the determination of the pH of polymer dispersions and rubber latices (natural and synthetic) by means of a pH-meter equipped with a combined glass and silver reference electrode. It is also suitable for prevulcanized latex and compounds containing polymer dispersions, including adhesives. Replaces the second edition.</p>"

42829,IS,Amd,ISO 976:1996/Amd 1:2006,Rubber and plastics — Polymer dispersions and rubber latices — Determination of pH — Amendment 1: Precision data,Caoutchouc et plastiques — Dispersions de polymères et latex de caoutchouc — Détermination du pH — Amendement 1: Données de fidélité,2006-02-02,3,['83.040.10'],ISO/TC 45/SC 3,9599,,[60896],"['en','fr']",2,

17623,IS,,ISO 9764:1989,Electric resistance and induction welded steel tubes for pressure purposes — Ultrasonic testing of the weld seam for the detection of longitudinal imperfections,Tubes en acier soudés par résistance électrique ou induction pour service sous pression — Contrôle par ultrasons du cordon de soudure pour la détection des imperfections longitudinales,1989-07-13,1,"['23.040.10','77.140.75','25.160.40']",ISO/TC 17/SC 19,9599,,[44667],"['en','fr']",3,"<p>Two different acceptance levels are considered in table 1. The choice between these acceptance levels will depend on the intended application. Specifies general requirements, method of test, reference standards, reference notch

17624,IS,,ISO 9765:1990,Submerged arc-welded steel tubes for pressure purposes — Ultrasonic testing of the weld seam for the detection of longitudinal and/or transverse imperfections,Tubes en acier soudés à l'arc submergé pour service sous pression — Contrôle par ultrasons du cordon de soudure pour la détection des imperfections longitudinales et/ou transversales,1990-11-15,1,"['23.040.10','77.140.75','25.160.40']",ISO/TC 17/SC 19,9599,,[44667],"['en','fr']",4,<p>Specifies requirements for the ultrasonic testing of weld seams for the detection of imperfections according to three different acceptance levels. Applies to inspections of tubular products with outside diameters of 150 mm or greate

17625,IS,,ISO 9766:1990,Drills with indexable inserts — Cylindrical shanks with a parallel flat,Forets à plaquettes amovibles — Queues cylindriques à méplat,1990-12-13,1,['25.100.30'],ISO/TC 29/SC 9,9599,,[60181],"['en','fr']",2,<p>Gives the dimensions necessary for the interchangeability of these shanks. The dimensions are shown in figure 1 and table 1. A hole shall be provided for axially feeding coolant through the drill.</p>

17627,IS,,ISO 9768:1990,Tea — Determination of water extract,Thé — Détermination de l'extrait à l'eau,1990-09-20,1,['67.140.10'],ISO/TC 34/SC 8,9599,[6168],[21061],"['en','fr']",2,

17631,IS,,ISO 9770:1989,Crude petroleum and petroleum products — Compressibility factors for hydrocarbons in the range 638 kg/m3 to 1 074 kg/m3,Pétrole brut et produits pétroliers — Facteurs de compressibilité des hydrocarbures dans la plage de 638 kg/m3 à 1074 kg/m3,1989-08-24,1,['75.080'],ISO/TC 28/SC 2,9599,,[65049],"['en','fr']",1,"<p>Includes the contents of Manual of Petroleum Measurement Standards, Chapter 11.2.1M published August 1984 by API. The purpose is to correct hydrocarbon volumes metered under pressure to the corresponding volumes at the equilibrium pressure for the metered temperature. Contains compressibility factors related to meter temperature and density of metered mater

17632,IS,,ISO 9771:1989,Plastics — Phenolic resins — Determination of reactivity of resols under acid conditions,Plastiques — Résines phénoliques — Détermination de la réactivité des résols dans des conditions acides,1989-12-14,1,['83.080.10'],ISO/TC 61/SC 12,9599,,[25125],"['en','fr']",2,

17633,IS,,ISO 9772:1994,Cellular plastics — Determination of horizontal burning characteristics of small specimens subjected to a small flame,"Plastiques alvéolaires — Détermination des caractéristiques de combustion de petites éprouvettes en position horizontale, soumises à une petite flamme",1994-07-28,1,"['13.220.40','83.100']",ISO/TC 61/SC 4,9599,,[31269],"['en','fr']",12,

31269,IS,,ISO 9772:2001,Cellular plastics — Determination of horizontal burning characteristics of small specimens subjected to a small flame,"Plastiques alvéolaires — Détermination des caractéristiques de combustion de petites éprouvettes en position horizontale, soumises à une petite flamme",2001-04-12,2,"['13.220.40','83.100']",ISO/TC 61/SC 4,9599,[17633],[54778],"['en','fr']",14,

34806,IS,Amd,ISO 9772:2001/Amd 1:2003,Cellular plastics — Determination of horizontal burning characteristics of small specimens subjected to a small flame — Amendment 1: Specimens,"Plastiques alvéolaires — Détermination des caractéristiques de combustion de petites éprouvettes en position horizontale, soumises à une petite flamme — Amendement 1: Éprouvettes",2003-10-16,2,"['13.220.40','83.100']",ISO/TC 61/SC 4,9599,,[54778],['en'],2,

54778,IS,,ISO 9772:2012,Cellular plastics — Determination of horizontal burning characteristics of small specimens subjected to a small flame,"Plastiques alvéolaires — Détermination des caractéristiques de combustion de petites éprouvettes en position horizontale, soumises à une petite flamme",2012-08-30,3,"['13.220.40','83.100']",ISO/TC 61/SC 4,9599,"[34806,31269]",[77448],"['en','ru']",17,"<p>ISO 9772:2012 specifies a small-scale laboratory screening procedure for comparing the relative burning characteristics of horizontally oriented, small cellular plastic specimens, having a density less than 250 kg/m³, when exposed to an ignition source.</p><p>This method of test is intended

17634,IS,,ISO 9773:1990,Plastics — Determination of burning behaviour of flexible vertical specimens in contact with a small-flame ignition source,Plastiques — Détermination du comportement au feu d'éprouvettes verticales souples au contact d'une petite flamme comme source d'allumage,1990-11-22,1,"['83.080.01','13.220.40']",ISO/TC 61/SC 4,9599,[5895],[26822],['en'],8,

26822,IS,,ISO 9773:1998,Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source,Plastiques — Détermination du comportement au feu d'éprouvettes minces verticales souples au contact d'une petite flamme comme source d'allumage,1998-02-26,2,"['83.080.01','13.220.40']",ISO/TC 61/SC 4,9599,[17634],[85513],"['en','fr']",11,

34807,IS,Amd,ISO 9773:1998/Amd 1:2003,Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source — Amendment 1: Specimens,Plastiques — Détermination du comportement au feu d'éprouvettes minces verticales souples au contact d'une petite flamme comme source d'allumage — Amendement 1: Éprouvettes,2003-10-13,2,"['83.080.01','13.220.40']",ISO/TC 61/SC 4,9599,,[85513],"['en','fr']",2,

17637,IS,,ISO 9775:1990,Small craft — Remote steering systems for single outboard motors of 15 kW to 40 kW power,Navires de plaisance — Appareils à gouverner commandés à distance pour moteurs hors-bord uniques de puissance comprise entre 15 kW et 40 kW,1990-12-20,1,['47.080'],ISO/TC 188,9599,,"[75540,75467]","['en','fr']",9,"<p>Specifies requirements and test methods for remote push-pull cable steering systems and their major component items, used for small craft with a single outboard motor of 15 kW to 40 kW power. Includes definitions, installation, test requirements, as-installed tests, component tests and outboard motor requirements. Components and functional details are given in figures

17641,IS,,ISO 9779:1990,Metallurgical-grade fluorspar — Determination of lead content — Solvent extraction atomic absorption spectrometric method,Spaths fluor utilisables dans l'industrie métallurgique — Dosage du plomb — Méthode par spectrométrie d'absorption atomique après extraction,1990-03-08,1,['73.080'],ISO/TC 175,9599,,[17642],"['en','fr']",4,

17645,IS,,ISO 9782:1993,Plastics — Reinforced moulding compounds and prepregs — Determination of apparent volatile-matter content,Plastiques renforcés — Compositions pour moulage et préimprégnés — Détermination de la teneur apparente en matières volatiles,1993-05-20,1,['83.120'],ISO/TC 61/SC 13,9599,,[91061],"['en','fr']",3,"<p>The apparent volatile-matter content is the percentage of matter lost on heating, relative to the initial mass, The principle of the method specified is obtaining it by measuring the change in mass of a test specimen when heated in an air-ventilated oven at a specified temperature for a specified length of time. The method is applicable to all unidirectional and multi

17646,IS,,ISO 9785:1990,Shipbuilding — Ventilation of cargo spaces where internal combustion engine vehicles may be driven — Calculation of theoretical total airflow required,Construction navale — Ventilation des espaces cargaison des navires dans lesquels des véhicules à moteur à combustion interne peuvent être utilisés — Calcul du débit d'air total théorique exigé,1990-08-16,1,['47.020.90'],ISO/TC 8/SC 3,9599,,[27018],"['en','fr']",7,

17647,IS,Cor,ISO 9785:1990/Cor 1:1991,Shipbuilding — Ventilation of cargo spaces where internal combustion engine vehicles may be driven — Calculation of theoretical total airflow required — Technical Corrigendum 1,Construction navale — Ventilation des espaces cargaison des navires dans lesquels des véhicules à moteur à combustion interne peuvent être utilisés — Calcul du débit d'air total théorique exigé — Rectificatif technique 1,1991-02-28,1,['47.020.90'],ISO/TC 8/SC 3,9599,,[27018],"['en','fr']",1,"<p>Concerns page 2, subclause 3.2.2.2: Replace the existing equation by the equation given in this technical corrigendum.</p>"

17649,IS,,ISO 9787:1990,Manipulating industrial robots — Coordinate systems and motions,Robots manipulateurs industriels — Systèmes de coordonnées et mouvements,1990-12-06,1,['25.040.30'],ISO/TC 184,9599,,[26484],"['en','fr']",5,

26484,IS,,ISO 9787:1999,Manipulating industrial robots — Coordinate systems and motion nomenclatures,Robots manipulateurs industriels — Systèmes de coordonnées et nomenclatures de mouvements,1999-05-13,2,['25.040.30'],ISO/TC 184,9599,[17649],[59444],"['en','fr']",10,

17650,IS,,ISO 9788:1990,"Air cargo equipment — Cast components of double stud fitting assembly with a load capacity of 22 250 N (5 000 lbf), for aircraft cargo restraint","Équipement pour le fret aérien — Composants de fonderie d'une ferrure à pion double, de capacité de charge de 22 250 N (5 000 lbf), pour l'arrimage du fret dans les aéronefs",1990-12-13,1,['49.120'],ISO/TC 20/SC 9,9599,,[70675],"['en','fr']",5,"<p>Deals with the geometry and requirements for assemblies, when installed in rail conforming to ISO 7166. Other materials than those specified in 4.2 may alternatively be used, provided the performance and testing requirements of this standard are complied with. Includes definition

3765,IS,,ISO 98:1977,Textile machinery and accessories — Spinning preparatory and spinning machinery — Covering characteristics of top rollers,Matériel pour l'industrie textile — Machines de préparation de filature et de filature — Caractéristiques des garnitures des cylindres supérieurs,1977-05-01,2,['59.120.10'],ISO/TC 72/SC 1,9599,,[25719],"['en','fr']",2,

17666,IS,,ISO 9801:1997,Ophthalmic instruments — Trial case lenses,Instruments ophtalmiques — Verres de boîte d'essai,1997-06-05,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[52492],"['en','fr']",11,

17667,IS,,ISO 9802:1996,Raw optical glass — Vocabulary,Verre d'optique brut — Vocabulaire,1996-10-24,1,"['81.040.10','01.040.81']",ISO/TC 172/SC 3,9599,,[77351],"['en','fr','ru']",53,"<p>Defines terms relating to raw optical glass and related manufacturing processes. Contains types of optical glasses, processes and materials, optical properties, non-optical properties and glass defects.</p>"

42464,IS,Cor,ISO 9802:1996/Cor 1:2005,Raw optical glass — Vocabulary — Technical Corrigendum 1,Verre d'optique brut — Vocabulaire — Rectificatif technique 1,2005-07-20,1,"['81.040.10','01.040.81']",ISO/TC 172/SC 3,9599,,[77351],"['en','fr','ru']",2,

40216,IS,,ISO 9803-1:2007,Vacuum technology — Mounting dimensions of pipeline fittings — Part 1: Non knife-edge flange type,Technique du vide — Dimensions de montage des raccords de conduit — Partie 1: Brides de type sans guillotine,2007-05-07,1,['23.160'],ISO/TC 112,9599,[17668],[79410],"['en','fr']",5,"<p>ISO 9803-1:2007 specifies mounting dimensions for vacuum pipeline fittings (elbows, tees and crosses) of non-bakable and non knife-edge flange for nominal bores from 10 mm to 250 mm of the R5 series.</p>"

17668,IS,,ISO 9803:1993,Vacuum technology — Pipeline fittings — Mounting dimensions,Technique du vide — Connexions à vide pour les pipelines — Dimensions de montage,1993-01-28,1,['23.160'],ISO/TC 112,9599,,"[40216,40217]","['en','fr']",2,"<p>Specifies the dimensions for vacuum pipeline fittings (elbows, tees and crosses) for nominal bores from 10 mm to 250 mm of the R5 series.</p>"

40217,IS,,ISO 9803-2:2007,Vacuum technology — Mounting dimensions of pipeline fittings — Part 2: Knife-edge flange type,Technique du vide — Dimensions de montage des raccords de conduit — Partie 2: Brides de type à guillotine,2007-05-07,1,['23.160'],ISO/TC 112,9599,[17668],[79411],"['en','fr']",5,"<p>ISO 9803-2:2007 specifies mounting dimensions for vacuum pipeline fittings (elbows, tees and crosses) of knife-edge flanges for nominal bores from 16 mm to 200 mm.</p>"

17678,IS,,ISO 9806-1:1994,Test methods for solar collectors — Part 1: Thermal performance of glazed liquid heating collectors including pressure drop,"Méthodes d'essai des capteurs solaires — Partie 1: Performance thermique des capteurs vitrés à liquide, chute de pression incluse",1994-12-08,1,['27.160'],ISO/TC 180,9599,,"[59879,32420]",['en'],60,<p>Establishes methods for determining the thermal performance of glazed liquid heating solar collectors; provides test methods and calculation procedures for determining the steady-state and quasi-steady-state thermal performance of solar collectors. Contains methods for conducting tests outdoors under natural solar irradiance and indoors under sim

17679,IS,,ISO 9806-2:1995,Test methods for solar collectors — Part 2: Qualification test procedures,Méthodes d'essai des capteurs solaires — Partie 2: Méthodes d'essai de qualification,1995-08-17,1,['27.160'],ISO/TC 180,9599,,"[59879,32419]",['en'],48,<p>Establishes test methods for testing solar collectors under well-defined and repeatable conditions. Determination of the ability to resist the influences of degrading agents.</p>

59879,IS,,ISO 9806:2013,Solar energy — Solar thermal collectors — Test methods,Énergie solaire — Capteurs thermiques solaires — Méthodes d'essai,2013-11-05,1,['27.160'],ISO/TC 180,9599,"[17678,17679,17680]",[67978],"['en','fr']",117,"<p>ISO 9806:2013 specifies test methods for assessing the durability, reliability and safety for fluid heating collectors.</p><p>It also includes test methods for the thermal performance characterization of fluid heating collectors, namely steady-state and quasi-dynamic thermal performance of glazed and unglazed liquid heating solar collectors and steady-state thermal performance of glazed and unglazed air heating solar collectors (open to ambient as well as clo

67978,IS,,ISO 9806:2017,Solar energy — Solar thermal collectors — Test methods,Énergie solaire — Capteurs thermiques solaires — Méthodes d'essai,2017-09-26,2,['27.160'],ISO/TC 180,9599,[59879],[78801],"['en','fr']",90,"<p>ISO 9806:2017 specifies test methods for assessing the durability, reliability, safety and thermal performance of fluid heating solar collectors. The test methods are applicable for laboratory testing and for <i>in situ</i> testing.</p><p>ISO 9806:2017 is applicable to all types of fluid heating solar collectors, air heating solar collectors, hybrid solar collectors co-generating heat and electric power, as well as to solar collectors using external power sources for normal

17680,IS,,ISO 9806-3:1995,Test methods for solar collectors — Part 3: Thermal performance of unglazed liquid heating collectors (sensible heat transfer only) including pressure drop,"Méthodes d'essai des capteurs solaires — Partie 3: Performance thermique des capteurs non vitrés à liquide (transfert de chaleur appréciable seulement), chute de pression incluse",1995-11-30,1,['27.160'],ISO/TC 180,9599,,"[59879,32418,59297]",['en'],36,<p>Establishes methods for determining the thermal performance of unglazed liquid heating solar collectors. Contains methods for conducting tests outdoors under natural solar irradiation and simulated wind and for conducting tests indoors under simulated solar irr

17681,IS,,ISO 9807:1991,Banking and related financial services — Requirements for message authentication (retail),Banque et services financiers liés aux opérations bancaires — Spécifications liées à l'authentification des messages (service aux particuliers),1991-12-16,1,['35.240.40'],ISO/TC 68/SC 2,9599,,[30381],"['en','fr']",11,<p>Specifies procedures to be used for protecting the integrity of retail banking messages and for verifying that the message originated from an authorized source. Describes the method by which algorithms are approved.</p>

17683,IS,,ISO 9809-1:1999,"Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa","Bouteilles à gaz — Bouteilles à gaz rechargeables en acier sans soudure — Conception, construction et essais — Partie 1: Bouteilles en acier trempé et revenu ayant une résistance à la traction inférieure à 1 100 MPa",1999-05-27,1,['23.020.35'],ISO/TC 58/SC 3,9599,,[41498],"['en','fr']",37,

41498,IS,,ISO 9809-1:2010,"Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa","Bouteilles à gaz — Bouteilles à gaz rechargeables en acier sans soudure — Conception, construction et essais — Partie 1: Bouteilles en acier trempé et revenu ayant une résistance à la traction inférieure à 1 100 MPa",2010-04-15,2,['23.020.35'],ISO/TC 58/SC 3,9599,[17683],[70377],"['en','fr']",41,"<p>ISO 9809-1:2010 specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at manufacture of refillable quenched

25892,IS,,ISO 9809-2:2000,"Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa","Bouteilles à gaz — Bouteilles à gaz rechargeables en acier sans soudure — Conception, construction et essais — Partie 2: Bouteilles en acier trempé et revenu ayant une résistance à la traction supérieure ou égale à 1 100 MPa",2000-06-22,1,['23.020.35'],ISO/TC 58/SC 3,9599,,[41499],"['en','fr']",42,

41499,IS,,ISO 9809-2:2010,"Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa","Bouteilles à gaz — Bouteilles à gaz rechargeables en acier sans soudure — Conception, construction et essais — Partie 2: Bouteilles en acier trempé et revenu ayant une résistance à la traction supérieure ou égale à 1 100 MPa",2010-04-15,2,['23.020.35'],ISO/TC 58/SC 3,9599,[25892],[70378],"['en','fr']",45,"<p>ISO 9809-2:2010 specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at manufactur

28341,IS,,ISO 9809-3:2000,"Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 3: Normalized steel cylinders","Bouteilles à gaz — Bouteilles à gaz rechargeables en acier sans soudure — Conception, construction et essais — Partie 3: Bouteilles en acier normalisé",2000-12-21,1,['23.020.35'],ISO/TC 58/SC 3,9599,"[29284,10687]",[41500],"['en','fr']",37,

41500,IS,,ISO 9809-3:2010,"Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 3: Normalized steel cylinders","Bouteilles à gaz — Bouteilles à gaz rechargeables en acier sans soudure — Conception, construction et essais — Partie 3: Bouteilles en acier normalisé",2010-04-15,2,['23.020.35'],ISO/TC 58/SC 3,9599,[28341],[70379],"['en','fr']",40,"<p>ISO 9809-3:2010 specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at manufacture of refillable normalized or normalized and tempered seamless steel gas cylinders of water capacities from 0,5 l up to and including 150 l fo

59839,IS,,ISO 9809-4:2014,"Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 4: Stainless steel cylinders with an Rm value of less than 1 100 MPa","Bouteilles à gaz — Bouteilles à gaz rechargeables en acier sans soudure — Conception, construction et essais — Partie 4: Bouteilles en acier inoxydable avec une valeur Rm inférieure à 1 100 MPa",2014-07-08,1,['23.020.35'],ISO/TC 58/SC 3,9599,,[76548],"['en','fr']",42,"<p>ISO 9809-4:2014 specifies the minimum requirements for the material, design, construction and workmanship, manufacturing processes, examinations, and tests at manufacture of refillable seamless stainless steel gas cylinders of water

76548,IS,,ISO 9809-4:2021,"Gas cylinders — Design, construction and testing of refillable seamless steel gas cylinders and tubes — Part 4: Stainless steel cylinders with an R m value of less than 1 100 MPa","Bouteilles à gaz — Conception, construction et essais des bouteilles à gaz et des tubes rechargeables en acier sans soudure — Partie 4: Bouteilles en acier inoxydable ayant une valeur de Rm inférieure à 1 100 MPa",2021-11-03,2,['23.020.35'],ISO/TC 58/SC 3,9599,[59839],[87936],"['en','fr']",54,"<p>This document specifies the minimum requirements for the materials, design, construction and workmanship, manufacturing processes, examinations and testing at time of manufacture for refillable,

17685,IS,,ISO 9815:1992,Passenger-car/trailer combinations — Lateral stability test,Ensemble voiture particulière/remorque — Essai de stabilité latérale,1992-07-16,1,['43.100'],ISO/TC 22,9599,,[29918],"['en','fr']",12,"<p>Specifies a test procedure to determine the damping characteristic of trailer oscillation excited by a defined steering impulse. Measurements are made of steering-wheel angle, forward velocity, lateral acceleration of the trailer, articulation angle between towing vehicle and trailer. If non-periodic instability is of interest, a steady-state circular test may be performed in accordance with annex C.</p>"

29918,IS,,ISO 9815:2003,Road vehicles — Passenger-car and trailer combinations — Lateral stability test,Véhicules routiers — Ensembles voiture particulière et remorque — Essai de stabilité latérale,2003-01-30,2,['43.100'],ISO/TC 22,9599,[17685],[54152],"['en','fr']",16,"<p>ISO 9815:2003 specifies a lateral stability test for passenger-car and trailer combinations. It is applicable to passenger cars in accordance with ISO 3833, and also to light-truck and trailer combinations. </p>"

54152,IS,,ISO 9815:2010,Road vehicles — Passenger-car and trailer combinations — Lateral stability test,Véhicules routiers — Ensembles voiture particulière et remorque — Essai de stabilité latérale,2010-04-30,3,['43.100'],ISO/TC 22/SC 33,9599,[29918],[83234],['en'],17,"<p>ISO 9815:2010 specifies a lateral stability test for passenger-car and trailer combinations. It is applicable to passenger cars in accordance with ISO 3833, and also to light trucks, and their trailer combinations. </p><p>The lateral stability test determines the damping characteristic of the yaw oscillation of such towing-vehicle–trailer combinations excited by a defined steering impulse. The combination is initially drive

17686,IS,,ISO 9816:1993,Passenger cars — Power-off reactions of a vehicle in a turn — Open-loop test method,Voitures particulières — Réponse d'un véhicule à un lever de pied en virage — Méthode d'essai en boucle ouverte,1993-10-07,1,['43.100'],ISO/TC 22,9599,,"[42037,31312]","['en','fr']",22,"<p>Applies to passenger cars as defined in ISO 3833. The purpose is to determine the power-off effect on course holding and directional behaviour of a vehicle, whose steady-state circular motion is disturbed by power-off only. The sudden release of the accelerator pedal causes this effect. It is not possible at present to use this procedure and test results for regulation purposes.</p>"

42037,IS,,ISO 9816:2006,Passenger cars — Power-off reaction of a vehicle in a turn — Open-loop test method,Voitures particulières — Réponse d'un véhicule à un lever de pied en virage — Méthode d'essai en boucle ouverte,2006-12-01,2,['43.100'],ISO/TC 22/SC 33,9599,[17686],[67975],"['en','fr']",23,"<p>ISO 9816:2006 specifies open-loop test methods to determine the reactions of a vehicle in a turn to a sudden drop in motive power resulting from release of the accelerator pedal. It applies to passenger cars as defined in ISO 3833.</p><p>The open-loop manoeuvre specified in this test method is not representative of real driving conditions, but is useful to obtain measures of a vehicle's power-off

17696,IS,,ISO 9825:1994,Measurement of liquid flow in open channels — Field measurement of discharge in large rivers and floods,Mesure de débit des liquides dans les canaux découverts — Mesurage in situ du débit des grandes rivières et des débits de crue,1994-06-16,1,['17.120.20'],ISO/TC 113/SC 1,9599,,[37574],"['en','fr']",6,<p>Deals specifically with the measurement of discharge in large rivers and the measurement of flood flows. Also describes the relevant field measurements when it becomes necessary to use indirect methods of estimating discharge.</p>

5422,IS,,ISO 983:1974,"Sodium hydroxide for industrial use — Determination of iron content — 1,10- Phenanthroline photometric method","Hydroxyde de sodium à usage industriel — Dosage du fer — Méthode photométrique à la 1,10- phénanthroline",1974-12-01,1,['71.060.40'],ISO/TC 47,9599,,[5423],"['en','fr']",2,"<p>Specifies a method that is more sensitive and more widely used than the 2,2'-bipyridyl method. It is applicable to products having iron contents equal to or greater than 0.5 mg/kg. The principle is based on the reduction of trivalent iron by hydroxylammonium chloride, formation of a bivalent iron/1,10-phenanthroline complex in a buffered system. Photometric measurement of the coloured c

17703,IS,,ISO 9832:1992,Animal and vegetable fats and oils — Determination of residual technical hexane content,Corps gras d'origines animale et végétale — Dosage de l'hexane technique résiduel,1992-12-10,1,['67.200.10'],ISO/TC 34/SC 11,9599,,[35661],"['en','fr']",5,<p>The method is based on desorption of volatile hydrocarbons by heating at 80 °C in a closed vessel after addition of an internal standard and determination of the particular volatile hydrocarbons content of the headspace by gas chromatography using packed or capillary columns.</p>

27490,IS,Amd,ISO 9832:1992/Amd 1:1998,Animal and vegetable fats and oils — Determination of residual technical hexane content — Amendment 1: Results of interlaboratory test,Corps gras d'origines animale et végétale — Dosage de l'hexane technique résiduel — Amendement 1: Résultats de l'essai interlaboratoire,1998-03-19,1,['67.200.10'],ISO/TC 34/SC 11,9599,,[35661],"['en','fr']",2,

17716,IS,,ISO 9836:1992,Performance standards in building — Definition and calculation of area and space indicators,Normes de performance dans le bâtiment — Définition et calcul des indicateurs de surface et de volume,1992-06-11,1,['91.040.01'],ISO/TC 59,9599,,[52307],"['en','fr']",9,"<p>In defining area measurement, uses the intra-muros and extra-muros concept. The indicators defined are intended for practical use, as a basis for measuring various aspects of the performance of buildings or as a planning aid. Intended to be used when establishing 1) specifications for the geometric performance of a building and its spaces, 2) technical documentation relating to the performance of whole build

52307,IS,,ISO 9836:2011,Performance standards in building — Definition and calculation of area and space indicators,Normes de performance dans le bâtiment — Définition et calcul des indicateurs de surface et de volume,2011-09-30,2,['91.040.01'],ISO/TC 59/SC 15,9599,[17716],[73149],['en'],19,"<p>ISO 9836:2011 deals with the definition and calculation of surface area and volume indicators.</p><p>In defining area measurement, ISO 9836:2011 uses three measurement concepts:</p><ol><li> the intra-muros and extra-muros concept used in many parts of the world;</li><li> the wall centre method of measurement used in many parts of the world;</li><li> variations on these methods to

17717,IS,,ISO 9838:1991,Alpine ski-bindings — Test soles for ski-binding tests,Fixations de skis alpins — Semelles d'essai pour les essais de fixations de skis,1991-07-18,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[41956],"['en','fr']",5,"<p>Defines a test sole representing a ski-boot, or at least the bottom part of it, to be used for testing alpine ski-bindings. Includes sole type A (for adults) and type C (for children).</p>"

41956,IS,,ISO 9838:2008,Alpine and touring ski-bindings — Test soles for ski-binding tests,Fixations de skis alpins et de randonnée — Semelles d'essai pour les essais de fixations de skis,2008-11-27,2,['97.220.20'],ISO/TC 83/SC 4,9599,[17717],[67738],"['en','fr']",9,"<p>ISO 9838:2008 defines test soles representing an alpine ski-boot (form A), or at least the bottom part of it, to be used for testing alpine ski-bindings for alpine skiing in accordance with ISO 9462 and ISO 9465 and a touring ski-boot (form T), or at least the bottom part of it, to be used for testing touring ski-bindings for touring skiing in accordance with ISO 13992 and ISO 9465.</p>"

67738,IS,,ISO 9838:2015,Alpine and touring ski-bindings — Test soles for ski-binding tests,Fixations de skis alpins et de randonnée — Semelles d'essai pour les essais de fixations de skis,2015-09-08,3,['97.220.20'],ISO/TC 83/SC 4,9599,[41956],[74868],"['en','fr']",9,"<p>ISO 9838:2015 defines test soles representing</p><p>- an alpine ski-boot (form A) or at least the bottom part of it to be used for testing alpine ski-bindings for alpine skiing in accordance with ISO 9462 and ISO 9465, and</p><p>- a touring ski-boot (form T) or at least the bottom part of it to be used for testing touring ski-bindings for touring skiing in accordance with ISO 13992 and ISO 9465.</p><p>NOTE

74868,IS,,ISO 9838:2019,Alpine and touring ski-bindings — Test soles for ski-binding tests,Fixations de skis alpins et de randonnée — Semelles d'essai pour les essais de fixations de skis,2019-03-13,4,['97.220.20'],ISO/TC 83/SC 4,9599,[67738],[84080],"['en','fr']",10,"<p>This document defines test soles representing</p><p>— an alpine ski-boot (form A) or at least the bottom part of it to be used for testing alpine ski-bindings for alpine skiing in accordance with ISO 9462 and ISO 9465, and</p><p>— a touring ski-boot (form T) or at least the bottom part of it to be used for testing touring ski-bindings for touring skiing in accordance with ISO 13992 and ISO 9465.</p><p>NOTE