Withdrawn and superseded ISO standards — page 183 of 246

16910,IS,,ISO 9260:1991,Agricultural irrigation equipment — Emitters — Specification and test methods,Matériel agricole d'irrigation — Goutteurs — Spécifications et méthodes d'essai,1991-11-28,1,['65.060.35'],ISO/TC 23/SC 18,9599,,[28459],"['en','fr']",6,"<p>Specifies mechanical and functional requirements of irrigation emitters with or without pressure regulation, test methods and the data to be supplied by the manufacturer. Gives 13 terms and definitions.</p>"

16911,IS,,ISO 9261:1991,Agricultural irrigation equipment — Emitting-pipe systems — Specification and test methods,Matériel agricole d'irrigation — Gaines de micro-irrigation — Spécifications et méthodes d'essai,1991-11-28,1,['65.060.35'],ISO/TC 23/SC 18,9599,,[28459],"['en','fr']",7,"<p>Specifies mechanical and functional requirements of pipes and their fittings, test methods and the data to be supplied by the manufacturer. Gives 16 terms and definitions.</p>"

5343,IS,,ISO 927:1982,Spices and condiments — Determination of extraneous matter content,Épices — Détermination de la teneur en matières étrangères,1982-12-01,2,['67.220.10'],ISO/TC 34/SC 7,9599,,"[5344,42504]","['en','fr']",1,"<p>Specifies a method based on the physical separation and weighing of the extraneous matter in a test portion. Lists the apparatus to be used and describes sampling, procedure, expression of results and the details to be included in the test report.</p>"

16920,IS,,ISO 9270:1992,7/24 tapers for tool shanks for automatic changing — Tapers for spindle noses,Cônes d'emmanchement d'outils à conicité 7/24 pour changement automatique — Cônes pour nez de broches,1992-11-24,1,['25.060.20'],ISO/TC 29,9599,,"[51517,50991]","['en','fr']",4,<p>Specifies the dimensions and tolerances. Conicity tolerances shall conform with the cone angle tolerance grade AT4 specified in ISO 1947.</p>

16921,IS,,ISO 9271:1992,Decontamination of radioactively contaminated surfaces — Testing of decontamination agents for textiles,Décontamination des surfaces contaminées par la radioactivité — Essai des agents de décontamination pour les textiles,1992-01-30,1,['13.280'],ISO/TC 85/SC 2,9599,,[82292],"['en','fr']",17,"<p>Gives definitions. Specifies the principle, the apparatus, the preparation of the test sample, the test agents and procedure, calculation of results, the test report and the consideration of other properties.</p>"

16926,IS,,ISO 9276-1:1990,Representation of results of particle size analysis — Part 1: Graphical representation,Représentation de données obtenues par analyse granulométrique — Partie 1: Représentation graphique,1990-11-08,1,['19.120'],ISO/TC 24/SC 4,9599,,[25860],"['en','fr']",7,

25860,IS,,ISO 9276-1:1998,Representation of results of particle size analysis — Part 1: Graphical representation,Représentation de données obtenues par analyse granulométrique — Partie 1: Représentation graphique,1998-06-11,2,['19.120'],ISO/TC 24/SC 4,9599,[16926],[85959],"['en','fr']",9,

39860,IS,Cor,ISO 9276-1:1998/Cor 1:2004,Representation of results of particle size analysis — Part 1: Graphical representation — Technical Corrigendum 1,Représentation de données obtenues par analyse granulométrique — Partie 1: Représentation graphique — Rectificatif technique 1,2004-01-21,2,['19.120'],ISO/TC 24/SC 4,9599,,[85959],"['en','fr']",2,

33997,IS,,ISO 9276-2:2001,Representation of results of particle size analysis — Part 2: Calculation of average particle sizes/diameters and moments from particle size distributions,Représentation de données obtenues par analyse granulométrique — Partie 2: Calcul des tailles/diamètres moyens des particules et des moments à partir de distributions granulométriques,2001-04-12,1,['19.120'],ISO/TC 24/SC 4,9599,,[57641],"['en','fr']",12,

16928,IS,,ISO 9277:1995,Determination of the specific surface area of solids by gas adsorption using the BET method,Détermination de l'aire massique (surface spécifique) des solides par adsorption de gaz à l'aide de la méthode BET,1995-05-18,1,['19.120'],ISO/TC 24/SC 4,9599,,"[43805,44941,43806]","['en','fr']",11,"<p>Specifies the determination of the total specific external and internal surface area of disperse or porous solids by measuring the amount of physically adsorbed gas according to the method of Brunauer, Emmett and Teller (BET method). The BET method is applicable only to adsorption isotherms of type II and type IV. The BET method cannot reliably be applied to type I isotherms or

44941,IS,,ISO 9277:2010,Determination of the specific surface area of solids by gas adsorption — BET method,Détermination de l'aire massique (surface spécifique) des solides par adsorption de gaz — Méthode BET,2010-08-20,2,['19.120'],ISO/TC 24/SC 4,9599,[16928],[71014],"['en','ru']",24,"<p>ISO 9277:2010 specifies the determination of the overall specific external and internal surface area of disperse (e.g. nano-powders) or porous solids by measuring the amount of physically adsorbed gas according to the Brunauer, Emmett and Teller (BET) method. It takes account of the International Union for Pure and Applied Chemistry (IUPAC) recommendations of 1984 and 1994.</p><p>The BET method is applicab

16929,IS,,ISO 9278:1992,Uranium dioxide pellets — Determination of density and amount of open and closed porosity — Boiling water method and penetration immersion method,Pastilles de dioxyde d'uranium — Détermination de la masse volumique et de la quantité de pores ouverts et fermés — Méthode à eau bouillante et méthode de pénétration par immersion,1992-03-05,1,['27.120.30'],ISO/TC 85/SC 5,9599,,[41199],"['en','fr']",8,"<p>Describes for two methods the principle, the apparatus, the procedure of the boiling water method and of the m-Xylene impregnation method, the precision, the expression of results and the contents of the test report.</p>"

5345,IS,,ISO 928:1980,Spices and condiments — Determination of total ash,Épices — Détermination des cendres totales,1980-02-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[26525],"['en','fr']",2,

16937,IS,,ISO 9283:1990,Manipulating industrial robots — Performance criteria and related test methods,Robots manipulateurs industriels — Critères de performance et méthodes d'essai correspondantes,1990-12-20,1,['25.040.30'],ISO/TC 184,9599,,[22244],"['en','fr']",4,

16938,IS,Amd,ISO 9283:1990/Amd 1:1991,Manipulating industrial robots — Performance criteria and related test methods — Amendment 1: Guide for selection of performance criteria for typical applications,Robots manipulateurs industriels — Critères de performance et méthodes d'essai correspondantes — Amendement 1: Guide pour le choix des critères de performance pour des applications typiques,1991-06-20,1,['25.040.30'],ISO/TC 184,9599,,[22244],['en'],1,

16939,IS,,ISO 9284:1992,Abrasive grains — Test-sieving machines,Grains abrasifs — Machine à tamiser de contrôle,1992-06-25,1,"['25.100.70','19.120']",ISO/TC 29/SC 5,9599,,"[60014,35200]","['en','fr']",4,"<p>Specifies the operational and technical requirements, and gives guidance on the installation, checking and maintenance of test-sieving machines. These machines are used for determining the size distribution of bonded and coated abrasive macrograins.</p>"

16941,IS,,ISO 9286:1997,Abrasive grains and crude — Chemical analysis of silicon carbide,Abrasifs en grains ou en roche — Analyse chimique du carbure de silicium,1997-01-22,1,['25.100.70'],ISO/TC 29/SC 5,9599,,[79154],"['en','fr']",22,<p>Relates to the chemical analysis of silicon carbide. Applicable for the determination of the surface impurities of abrasive grains and determining the SiC content of crushed crude when the silicon carbide content is greater than 95 %.</p>

16943,IS,,ISO 9288:1989,Thermal insulation — Heat transfer by radiation — Physical quantities and definitions,Isolation thermique — Transfert de chaleur par rayonnement — Grandeurs physiques et définitions,1989-12-14,1,"['01.060','27.220']",ISO/TC 163,9599,,[82088],"['en','fr']",17,"<p>Contains general terms, terms related to surfaces either receiving, transferring or emitting a thermal radiation, terms related to surfaces emitting a thermal radiation, terms related to opaque or semi-transparent surfaces receiving a thermal radiation, terms related to a semi-transparent medium receiving a thermal radiation, and their definition.</p>"

5346,IS,,ISO 929:1980,Spices and condiments — Determination of water-insoluble ash,Épices — Détermination des cendres insolubles dans l'eau,1980-02-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[5347],"['en','fr']",2,

16945,IS,,ISO 9290:1990,Textiles — Woven fabrics — Determination of tear resistance by the falling pendulum method,Textiles — Tissus — Détermination de la résistance au déchirement par la méthode du mouton-pendule,1990-11-15,1,['59.080.30'],ISO/TC 38,9599,,[23369],"['en','fr']",5,

16946,IS,,ISO 9291:1996,Textile-glass-reinforced plastics — Rovings — Preparation of unidirectional plates by winding,Plastiques renforcés de verre textile — Stratifils — Préparation de plaques unidirectionnelles par enroulement,1996-10-24,1,['83.120'],ISO/TC 61/SC 13,9599,,[27247],"['en','fr']",6,

16948,IS,,ISO 9293:1987,Information processing — Volume and file structure of flexible disk cartridges for information interchange,Traitement de l'information — Volume et structure des fichiers des cartouches à disquette pour l'échange d'information,1987-04-09,1,['35.220.20'],ISO/IEC JTC 1,9599,,[21273],"['en','fr']",23,

16950,IS,,ISO 9295:1988,Acoustics — Measurement of high-frequency noise emitted by computer and business equipment,Acoustique — Mesurage du bruit à haute fréquence émis par les matériels informatiques et de bureau,1988-11-10,1,"['35.020','17.140.20']",ISO/TC 43/SC 1,9599,,"[30367,32302]","['en','fr']",11,"<p>Specifies four methods for the determination of sound power levels in the frequency range between 11,2 kHz and 22,4 kHz with the centre frequency of 16 kHz. The first three methods are based on the reverberation room technique, the fourth on a free field over a reflecting plane.</p>"

16951,IS,,ISO 9296:1988,Acoustics — Declared noise emission values of computer and business equipment,Acoustique — Valeurs déclarées d'émission acoustique des matériels informatiques et de bureau,1988-04-14,1,"['35.020','17.140.20']",ISO/TC 43/SC 1,9599,,"[30368,32303]","['en','fr']",7,"<p>Specifies the method of determining these values; acoustical and product information to be given in technical documents supplied to users by the manufacturer; the method for verifying the declared noise emission values given by the manufacturers.The basic values are the declared A-weighted sound power level and the declared A-weighted sound pressure level, at the operator or bystander positions.</p>" 16952

16953,IS,,ISO 9298:1995,Rubber compounding ingredients — Zinc oxide — Test methods,Ingrédients de mélange du caoutchouc — Oxyde de zinc — Méthodes d'essai,1995-11-23,1,['83.040.20'],ISO/TC 45/SC 3,9599,,[70403],"['en','fr']",9,<p>Gives the methods to be used for the evaluation of zinc oxide for use in the rubber industry. Applicable to all types of commercial zinc oxide. Zinc oxide can also be coated with organic substances in order to improve the dispersion in rubber.</p>

3753,IS,,ISO 93-1:1982,Textile machinery and accessories — Cylindrical sliver cans — Part 1: Main dimensions,Matériel pour l'industrie textile — Pots cylindriques pour rubans — Partie 1: Dimensions principales,1982-12-01,2,['59.120.10'],ISO/TC 72/SC 1,9599,"[3754,3752,3756]",[25718],"['en','fr']",3,

25718,IS,,ISO 93-1:1998,Textile machinery and accessories — Cylindrical sliver cans — Part 1: Main dimensions,Matériel pour l'industrie textile — Pots cylindriques pour rubans — Partie 1: Dimensions principales,1998-12-17,3,['59.120.10'],ISO/TC 72/SC 1,9599,[3753],[40270],"['en','fr']",5,

3755,IS,,ISO 93-2:1978,Textile machinery and accessories — Cylindrical sliver cans — Part 2: Spring bottoms,Matériel pour l'industrie textile — Pots cylindriques pour rubans — Partie 2: Fonds à ressort,1978-11-01,1,['59.120.10'],ISO/TC 72/SC 1,9599,,[24055],"['en','fr']",3,

24055,IS,,ISO 93-2:1999,Textile machinery and accessories — Cylindrical sliver cans — Part 2: Spring bottoms,Matériel pour l'industrie textile — Pots cylindriques pour rubans — Partie 2: Fonds à ressort,1999-05-13,2,['59.120.10'],ISO/TC 72/SC 1,9599,[3755],[40271],"['en','fr']",5,

5348,IS,,ISO 930:1980,Spices and condiments — Determination of acid-insoluble ash,Épices — Détermination des cendres insolubles dans l'acide,1980-02-01,1,['67.220.10'],ISO/TC 34/SC 7,9599,,[26524],"['en','fr']",2,

16956,IS,,ISO 9300:1990,Measurement of gas flow by means of critical flow Venturi nozzles,Mesure de débit de gaz au moyen de Venturi-tuyères en régime critique,1990-07-24,1,['17.120.10'],ISO/TC 30/SC 2,9599,,[34272],"['en','fr']",16,

34272,IS,,ISO 9300:2005,Measurement of gas flow by means of critical flow Venturi nozzles,Mesure de débit de gaz au moyen de Venturi-tuyères en régime critique,2005-08-19,2,['17.120.10'],ISO/TC 30/SC 2,9599,[16956],[77401],"['en','fr']",38,"<p>ISO 9300:2005 specifies the geometry and method of use (installation in a system and operating conditions) of critical flow Venturi nozzles (CFVN) used to determine the mass flow-rate of a gas flowing through a system. It also gives the information necessary for calculating the flow-rate and its associated uncertainty. It is applicable to Venturi nozzles in which the gas flow accelerates to the critical velocity at the throat (this being equal to the l

16958,IS,,ISO 9302:1989,Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Electromagnetic testing for verification of hydraulic leak-tightness,Tubes en acier sans soudure et soudés (sauf à l'arc immergé) pour service sous pression — Contrôle électromagnétique pour vérification de l'étanchéité,1989-06-29,1,"['77.040.20','77.140.30','23.040.10']",ISO/TC 17/SC 19,9599,,[16959],"['en','fr']",5,

16959,IS,,ISO 9302:1994,Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Electromagnetic testing for verification of hydraulic leak-tightness,Tubes en acier sans soudure et soudés (sauf à l'arc immergé) pour service sous pression — Contrôle électromagnétique pour vérification de l'étanchéité,1994-02-10,2,"['77.040.20','23.040.10','77.140.75']",ISO/TC 17/SC 19,9599,[16958],[44662],"['en','fr']",8,"<p>Specifies requirements for electromagnetic testing. The principle of the method is testing using a concentric coil or a rotating tube/pancake coil eddy current technique, or a rotating tube/magnetic transducer flux leakage technique.</p>"

16960,IS,,ISO 9303:1989,Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of longitudinal imperfections,Tubes en acier sans soudure et soudés (sauf à l'arc immergé) pour service sous pression — Contrôle par ultrasons sur toute la circonférence pour la détection des imperfections longitudinales,1989-07-13,1,"['77.040.20','23.040.10','77.140.75']",ISO/TC 17/SC 19,9599,,[44665],"['en','fr']",4,"<p>Is applicable to the inspection of tubes with an outside diameter greater than or equal to 9 mm, and with an outside diameter-to-thickness ratio greater than or equal to 5. Specifies general requirements, method o

16961,IS,,ISO 9304:1989,Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Eddy current testing for the detection of imperfections,Tubes en acier sans soudure et soudés (sauf à l'arc immergé) pour service sous pression — Contrôle par courants de Foucault pour la détection des imperfections,1989-06-29,1,"['77.040.20','23.040.10','77.140.75']",ISO/TC 17/SC 19,9599,,[44664],"['en','fr']",7,"<p>Is applicable to the inspection of tubes with an outside diameter greater than or equal to 4 mm and includes two different acceptance levels. Specifies general requirements, method of test, reference standards, reference notch, equipment calibration and checking, accepta

16962,IS,,ISO 9305:1989,Seamless steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of transverse imperfections,Tubes en acier sans soudure pour service sous pression — Contrôle aux ultrasons sur toute la circonférence pour la détection des imperfections transversales,1989-06-29,1,"['77.040.20','23.040.10','77.140.75']",ISO/TC 17/SC 19,9599,,[44665],"['en','fr']",4,"<p>Applicable to the inspection of tubes with an outside diameter greater than or equal to 9 mm. Specifies general requirements, method of test, reference notches, equipment calibration and checking, acceptance and test report.</p>"

16966,IS,,ISO 9308-1:1990,"Water quality — Detection and enumeration of coliform organisms, thermotolerant coliform organisms and presumptive Escherichia coli — Part 1: Membrane filtration method","Qualité de l'eau — Recherche et dénombrement des organismes coliformes, des organismes coliformes thermotolérants et des Escherichia coli présumés — Partie 1: Méthode de filtration sur membrane",1990-09-20,1,['07.100.20'],ISO/TC 147/SC 4,9599,,[26404],"['en','fr']",10,

26404,IS,,ISO 9308-1:2000,Water quality — Detection and enumeration of Escherichia coli and coliform bacteria — Part 1: Membrane filtration method,Qualité de l'eau — Recherche et dénombrement des Escherichia coli et des bactéries coliformes — Partie 1: Méthode par filtration sur membrane,2000-09-21,2,['07.100.20'],ISO/TC 147/SC 4,9599,[16966],"[55832,43322]","['en','fr','ru']",10,

45799,IS,Cor,ISO 9308-1:2000/Cor 1:2007,Water quality — Detection and enumeration of Escherichia coli and coliform bacteria — Part 1: Membrane filtration method — Technical Corrigendum 1,Qualité de l'eau — Recherche et dénombrement des Escherichia coli et des bactéries coliformes — Partie 1: Méthode par filtration sur membrane — Rectificatif technique 1,2007-06-14,2,['07.100.20'],ISO/TC 147/SC 4,9599,,[55832],"['en','fr','ru']",2,

16967,IS,,ISO 9308-2:1990,"Water quality — Detection and enumeration of coliform organisms, thermotolerant coliform organisms and presumptive Escherichia coli — Part 2: Multiple tube (most probable number) method","Qualité de l'eau — Recherche et dénombrement des organismes coliformes, des organismes coliformes thermotolérants et des Escherichia coli présumés — Partie 2: Méthode du nombre le plus probable",1990-09-20,1,['07.100.20'],ISO/TC 147/SC 4,9599,,"[52246,26405]","['en','fr']",9,

16968,IS,,ISO 9309:1989,Refrigerant compressors — Presentation of performance data,Compresseurs pour fluides frigorigènes — Présentation des performances,1989-06-08,1,['27.200'],ISO/TC 86/SC 4,9599,,"[53789,22687]","['en','fr']",2,"<p>The rating conditions are given in publications produced by various organizations such as CECOMAF for different practical uses. Because of many varying conditions in the presentation of performance data, it is not possible to make a direct comparison. Specified are therfore the items of performance data relating to the refrigerating capacity and power absorbed so that such comparisons may be made.</p>"

34449,IS,,ISO 9311-2:2002,Adhesives for thermoplastic piping systems — Part 2: Determination of shear strength,Adhésifs pour réseaux de tuyauteries en matières thermoplastiques — Partie 2: Détermination de la résistance au cisaillement,2002-08-29,1,"['23.040.01','83.180']",ISO/TC 138/SC 5,9599,,[51920],['en'],6,

16971,IS,,ISO 9312:1990,Resistance welding equipment — Insulated pins for use in electrode back-ups,Équipement de soudage par résistance — Fiches isolées utilisées dans les contre-électrodes,1990-07-19,1,['25.160.30'],ISO/TC 44/SC 6,9599,,"[61411,57036]","['en','fr']",2,

16980,IS,,ISO 9316:1989,Information processing systems — Small Computer System Interface (SCSI),Systèmes de traitement de l'information — Interface système pour petits ordinateurs (SCSI),1989-07-27,1,['35.200'],ISO/IEC JTC 1/SC 25,9599,,[23693],['en'],170,

16999,IS,,ISO 9328-1:1991,Steel plates and strips for pressure purposes — Technical delivery conditions — Part 1: General requirements,Tôles et bandes en acier pour service sous pression — Conditions techniques de livraison — Partie 1: Prescriptions générales,1991-12-05,1,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[7595,7592,7596]",[34983],"['en','fr']",19,"<p>Applies to unalloyed and low-alloyed steels, nickel-alloyed steels, weldable fine grain steels, and austenitic steels. Parts 1 to 5 of ISO 9328 cancel and replace the first editions of ISO 2604-4:1975, ISO/TR 2604-7:1986 and ISO 2604-8:1985.</p>"

34983,IS,,ISO 9328-1:2003,Steel flat products for pressure purposes — Technical delivery conditions — Part 1: General requirements,Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 1: Exigences générales,2003-11-07,2,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[16999],[51718],"['en','fr']",13,<p>ISO 9328-1:2003 specifies the general technical delivery conditions for steel flat products (plate/sheet and strip) used principally for the construction of pressure equipment.</p><p>The general technical delivery requirements in ISO 404 also apply to products supplied in accordance with ISO 9328-1:2003.</p>

51718,IS,,ISO 9328-1:2011,Steel flat products for pressure purposes — Technical delivery conditions — Part 1: General requirements,Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 1: Exigences générales,2011-04-20,3,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[34983],[72060],"['en','ru']",16,<p>ISO 9328-1:2011 specifies the general technical delivery conditions for steel flat products (plate/sheet and strip) used principally for the construction of pressure equipment.</p><p>The general technical delivery requirements in ISO 404 also apply to products supplied in accordance with ISO 9328-1:2011.</p>

17000,IS,,ISO 9328-2:1991,Steel plates and strips for pressure purposes — Technical delivery conditions — Part 2: Unalloyed and low-alloyed steels with specified room temperature and elevated temperature properties,Tôles et bandes en acier pour service sous pression — Conditions techniques de livraison — Partie 2: Aciers non alliés et faiblement alliés à propriétés spécifiées à températures ambiante et élevée,1991-12-05,1,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[7595,7592,7596]",[34984],"['en','fr']",13,"<p>Applies to plates of 3 mm to 150 mm thickness (partly up to 300 mm) and strip of thickness greater than or equal to 3 mm. Parts 1 to 5 of ISO 9328 cancel and replace the first e

34984,IS,,ISO 9328-2:2004,Steel flat products for pressure purposes — Technical delivery conditions — Part 2: Non-alloy and alloy steels with specified elevated temperature properties,Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 2: Aciers non alliés et aciers alliés avec caractéristiques spécifiées à température élevée,2004-08-05,2,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[17000],[53419],"['en','fr']",31,<p>ISO 9328-2:2004 specifies the technical delivery conditions for plates and strip for pressure equipment made of certain non-alloy and alloy steels. The requirements and definitions of ISO 9328-1 also apply to this document.</p> 3

53419,IS,,ISO 9328-2:2011,Steel flat products for pressure purposes — Technical delivery conditions — Part 2: Non-alloy and alloy steels with specified elevated temperature properties,Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 2: Aciers non alliés et aciers alliés avec caractéristiques spécifiées à température élevée,2011-04-20,3,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[34984],[72061],"['en','ru']",29,<p>ISO 9328-2:2011 specifies the technical delivery conditions for plates and strip for pressure equipment made of non-alloy and alloy steels. The requirements and definitions of ISO 9328-1:2011 also apply to ISO 9328-2:2011.</p> 53

17001,IS,,ISO 9328-3:1991,Steel plates and strips for pressure purposes — Technical delivery conditions — Part 3: Nickel-alloyed steels with specified low temperature properties,Tôles et bandes en acier pour service sous pression — Conditions techniques de livraison — Partie 3: Aciers alliés au nickel à propriétés spécifiées à basses températures,1991-12-05,1,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[7595,7592,7596]",[34986],"['en','fr']",7,"<p>Applies to plates and strip of 3 mm to 50 mm thickness. Parts 1 to 5 of ISO 9328 cancel and replace the first editions of ISO 2604-4:1975, ISO/TR 2604-7:1986 and ISO 2604-8:1985.</p>"

34985,IS,,ISO 9328-3:2004,"Steel flat products for pressure purposes — Technical delivery conditions — Part 3: Weldable fine grain steels, normalized","Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 3: Aciers soudables à grains fins, normalisés",2004-08-10,2,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[17002],[57549],"['en','fr']",18,<p>ISO 9328-3:2004 specifies the requirements for flat products for pressure equipment made of certain weldable fine grain steels. The requirements and definitions of ISO 9328-1 also apply to this document.</p>

57549,IS,,ISO 9328-3:2011,"Steel flat products for pressure purposes — Technical delivery conditions — Part 3: Weldable fine grain steels, normalized","Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 3: Aciers soudables à grains fins, normalisés",2011-04-20,3,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[34985,51722]",[72062],"['en','ru']",18,<p>ISO 9328-3:2011 specifies the requirements for flat products for pressure equipment made of weldable fine grain steels. The requirements and definitions of ISO 9328-1:2011 also apply to ISO 9328-3:2011.</p>

17002,IS,,ISO 9328-4:1991,Steel plates and strips for pressure purposes — Technical delivery conditions — Part 4: Weldable fine grain steels with high proof stress supplied in the normalized or quenched and tempered condition,"Tôles et bandes en acier pour service sous pression — Conditions techniques de livraison — Partie 4: Aciers à grains fins soudables à valeur élevée de limite conventionnelle d'élasticité, livrés à l'état normalisé ou trempé et revenu",1991-12-05,1,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[7595,7592,7596]","[34218,34985]","['en','fr']",12,"<p>Applies to plates of 3 mm to 70 mm thickness and strip of thickness greater than or equal to 3 mm. Parts 1 to 5 of ISO 9

34986,IS,,ISO 9328-4:2004,Steel flat products for pressure purposes — Technical delivery conditions — Part 4: Nickel-alloy steels with specified low temperature properties,Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 4: Aciers alliés au nickel avec caractéristiques spécifiées à basse température,2004-08-10,2,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[17001],[57550],"['en','fr']",13,<p>ISO 9328-4:2004 specifies the technical delivery conditions for plates and strip for pressure equipment made of certain nickel-alloy steels. The requirements and definitions of ISO 9328-1 also apply to this document.</p>

57550,IS,,ISO 9328-4:2011,Steel flat products for pressure purposes — Technical delivery conditions — Part 4: Nickel-alloy steels with specified low temperature properties,Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 4: Aciers alliés au nickel avec caractéristiques spécifiées à basse température,2011-04-20,3,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[51723,34986]",[72063],"['en','ru']",13,<p>ISO 9328-4:2011 specifies the technical delivery conditions for plates and strip for pressure equipment made of nickel-alloy steels.</p><p>The requirements and definitions of ISO 9328-1:2011 also apply to ISO 9328-4:2011.</p>

17003,IS,,ISO 9328-5:1991,Steel plates and strips for pressure purposes — Technical delivery conditions — Part 5: Austenitic steels,Tôles et bandes en acier pour service sous pression — Conditions techniques de livraison — Partie 5: Aciers austénitiques,1991-12-05,1,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[7595,7592,7596]",[34219],"['en','fr']",12,"<p>Applies to plates of 3 mm to 75 mm thickness and strip of thickness greater than or equal to 3 mm. Parts 1 to 5 of ISO 9328 cancel and replace the first editions of ISO 2604-4:1975, ISO/TR 2604-7:1986 and ISO 2604-8:1985.</p>"

34987,IS,,ISO 9328-5:2004,"Steel flat products for pressure purposes — Technical delivery conditions — Part 5: Weldable fine grain steels, thermomechanically rolled","Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 5: Aciers soudables à grains fins, laminés thermomécaniquement",2004-08-16,2,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,,[57551],"['en','fr']",15,"<p>ISO 9328-5:2004 specifies the requirements for flat products for pressure equipment, made of thermomechanically rolled fine grain steels. The steels are not suitable for hot forming. The requirements and definitions of ISO 9328-1 also apply to this document.</p>"

57551,IS,,ISO 9328-5:2011,"Steel flat products for pressure purposes — Technical delivery conditions — Part 5: Weldable fine grain steels, thermomechanically rolled","Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 5: Aciers soudables à grains fins, laminés thermomécaniquement",2011-04-20,3,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[34987,51724]",[72064],"['en','ru']",15,"<p>ISO 9328-5:2011 specifies the requirements for flat products for pressure equipment, made of thermomechanically rolled weldable fine grain steels. The steels are not suitable for hot forming.</p><p>Until now, no sufficient data for the standardization of the elevat

34218,IS,,ISO 9328-6:2004,"Steel flat products for pressure purposes — Technical delivery conditions — Part 6: Weldable fine grain steels, quenched and tempered","Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 6: Aciers soudables à grains fins, trempés et revenus",2004-08-10,1,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[17002],[57552],"['en','fr']",14,<p>ISO 9328-6:2004 specifies the requirements for flat products for pressure equipment made of quenched and tempered fine grain steels. The requirements and definitions in ISO 9328-1 also apply to this document.</p>

57552,IS,,ISO 9328-6:2011,"Steel flat products for pressure purposes — Technical delivery conditions — Part 6: Weldable fine grain steels, quenched and tempered","Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 6: Aciers soudables à grains fins, trempés et revenus",2011-04-20,2,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,"[34218,51725]",[72065],"['en','ru']",14,<p>ISO 9328‑6:2011 specifies the requirements for flat products for pressure equipment made of quenched and tempered weldable fine grain steels. The requirements and definitions in ISO 9328‑1:2011 also apply to ISO 9328‑6:2011.</p>

34219,IS,,ISO 9328-7:2004,Steel flat products for pressure purposes — Technical delivery conditions — Part 7: Stainless steels,Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 7: Aciers inoxydables,2004-05-11,1,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[17003],[51726],"['en','fr']",44,"<p>ISO 9328-7:2004 specifies the technical delivery conditions for flat products for pressure purposes made of stainless steels, including austenitic creep resisting steels.</p>"

51726,IS,,ISO 9328-7:2011,Steel flat products for pressure purposes — Technical delivery conditions — Part 7: Stainless steels,Produits plats en acier pour service sous pression — Conditions techniques de livraison — Partie 7: Aciers inoxydables,2011-04-20,2,"['77.140.30','77.140.50']",ISO/TC 17/SC 10,9599,[34219],[72066],"['en','ru']",49,"<p>ISO 9328-7:2011 specifies requirements for flat products for pressure purposes made of stainless steels, including austenitic creep-resisting steels.</p><p>Additionally the requirements of ISO 9328-1:2011 also apply.</p>"

17015,IS,,ISO 9333:1990,Dentistry -Brazing materials,Art dentaire - Produits pour brasage,1990-05-24,1,['11.060.10'],ISO/TC 106/SC 2,9599,,"[36589,40139]","['en','fr']",4,<p>Specification of requirements and test methods for brazing materials suitable for use in brazing cast dental restorations. Important terms are defined. Specific qualitative and quantitative requirements for freedom from biological hazard are not included.</p>

40139,IS,,ISO 9333:2006,Dentistry — Brazing materials,Art dentaire — Produits pour brasage,2006-07-12,2,['11.060.10'],ISO/TC 106/SC 2,9599,[17015],[78377],"['en','fr']",8,<p>ISO 9333:2006 specifies requirements and test methods for brazing materials suitable for use in metallic restorations.</p>

17016,IS,,ISO 9334:1995,Optics and optical instruments — Optical transfer function — Definitions and mathematical relationships,Optique et instruments d'optique — Fonction de transfert optique — Définitions et relations mathématiques,1995-10-19,1,['17.180.01'],ISO/TC 172/SC 1,9599,,[44594],"['en','fr','ru']",25,"<p>Defines terms relating to the optical transfer function and indicates, where pertinent, the mathematical relationships between those terms. Defines also important parameters that should be specified in connection with optical transfer function testing.</p>"

44594,IS,,ISO 9334:2007,Optics and photonics — Optical transfer function — Definitions and mathematical relationships,Optique et photonique — Fonction de transfert optique — Définitions et relations mathématiques,2007-05-15,2,['17.180.01'],ISO/TC 172/SC 1,9599,[17016],[57563],"['en','fr','ru']",29,"<p>ISO 9334:2006 defines terms relating to the optical transfer function and indicates, where pertinent, the mathematical relationships between those terms. It also defines important parameters that should be specified in connection with optical transfer function testing.</p><p>The terms and parameters defined in this ISO 9334:2006 apply to all measurements of the optical transfer function for opt

17017,IS,,ISO 9335:1995,Optics and photonics — Optical transfer function — Principles and procedures of measurement,Optique et photonique — Fonction de transfert optique — Principes et procédures de mesure,1995-11-23,1,['17.180.01'],ISO/TC 172/SC 1,9599,,[57565],"['en','fr']",20,<p>Gives general guidance for the construction and use of equipment for measurement of the optical transfer function of imaging systems and general rules for equipment performance requirements. Specifies important factors that can influence the measurements. Does not contain instruments for interferometric tests.</p>

43233,IS,Cor,ISO 9335:1995/Cor 1:2005,Optics and photonics — Optical transfer function — Principles and procedures of measurement — Technical Corrigendum 1,Optique et photonique — Fonction de transfert optique — Principes et procédures de mesure — Rectificatif technique 1,2005-11-14,1,['17.180.01'],ISO/TC 172/SC 1,9599,,[57565],"['en','fr']",2,

57565,IS,,ISO 9335:2012,Optics and photonics — Optical transfer function — Principles and procedures of measurement,Optique et photonique — Fonction de transfert optique — Principes et procédures de mesure,2012-10-01,2,['17.180.01'],ISO/TC 172/SC 1,9599,"[17017,43233]",[85989],"['en','fr']",24,"<p>ISO 9335:2012 gives general guidance for the construction and use of equipment for measurement of the optical transfer function (OTF) of imaging systems.</p><p>It specifies important factors that can influence the measurement of the OTF, and gives general rules for equipment performance requirements and environmental controls. It specifies important precautions that should be taken to ensure accura

17018,IS,,ISO 9336-1:1994,Optics and optical instruments — Optical transfer function — Application — Part 1: Interchangeable lenses for 35 mm still cameras,Optique et instruments d'optique — Fonction de transfert optique — Application — Partie 1: Objectifs interchangeables pour appareils photographiques de 35 mm,1994-10-13,1,['37.040.10'],ISO/TC 172/SC 1,9599,,[54927],"['en','fr']",4,<p>Specifies a method of testing interchangeable lenses for 35 mm still cameras with a picture format of 24 mm × 36 mm in terms of imaging states aimed at making valid optical transfer function measurements. Does not cover special lenses for macrophotography.</p>

17020,IS,,ISO 9336-3:1994,Optics and optical instruments — Optical transfer function — Application — Part 3: Telescopes,Optique et instruments d'optique — Fonction de transfert optique — Application — Partie 3: Télescopes,1994-10-13,1,['37.020'],ISO/TC 172/SC 4,9599,,"[75280,50742]","['en','fr']",10,<p>Specifies a method of testing telescopes in terms of imaging states aimed at making valid optical transfer function measurements and also information on the testing of some of their components and sub-assemblies.</p>

17021,IS,,ISO 9337-1:1999,Contact lenses — Determination of back vertex power — Part 1: Method using focimeter with manual focusing,Lentilles de contact — Détermination de la puissance frontale arrière — Partie 1: Méthode utilisant un frontofocomètre à mise au point manuelle,1999-05-06,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",8,

27467,IS,,ISO 9337-2:2004,Contact lenses — Determination of back vertex power — Part 2: Measurement of contact lenses immersed in saline,Lentilles de contact — Détermination de la puissance frontale arrière — Partie 2: Mesurage des lentilles de contact immergées dans une solution saline,2004-07-13,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",9,<p>ISO 9337-2:2004 describes test methods for the determination of back vertex power of soft contact lenses immersed in saline. It is applicable to finished contact lenses.</p>

17022,IS,,ISO 9338:1996,Optics and optical instruments — Contact lenses — Determination of the diameters,Optique et instruments d'optique — Lentilles de contact — Détermination des diamètres,1996-10-10,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",8,

17023,IS,,ISO 9339-1:1996,Optics and optical instruments — Contact lenses — Determination of the thickness — Part 1: Rigid contact lenses,Optique et instruments d'optique — Lentilles de contact — Détermination de l'épaisseur — Partie 1: Lentilles de contact rigides,1996-08-22,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",3,<p>Specifies a method for the determination of the thickness of rigid contact lenses. For the purposes of this standard the definitions given in ISO 8320 apply.</p>

25850,IS,,ISO 9339-2:1998,Optics and optical instruments — Contact lenses — Determination of thickness — Part 2: Hydrogel contact lenses,Optique et instruments d'optique — Lentilles de contact — Détermination de l'épaisseur — Partie 2: Lentilles de contact en hydrogel,1998-10-15,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",6,

33790,IS,Cor,ISO 9339-2:1998/Cor 1:2000,Optics and optical instruments — Contact lenses — Determination of thickness — Part 2: Hydrogel contact lenses — Technical Corrigendum 1,Optique et instruments d'optique — Lentilles de contact — Détermination de l'épaisseur — Partie 2: Lentilles de contact en hydrogel — Rectificatif technique 1,2000-04-27,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",1,

17025,IS,,ISO 9341:1996,Optics and optical instruments — Contact lenses — Determination of inclusions and surface imperfections for rigid contact lenses,Optique et instruments d'optique — Lentilles de contact — Détermination des inclusions et imperfections de surface des lentilles de contact rigides,1996-08-22,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[34479],"['en','fr']",3,<p>Describes a procedure for the assessment of inclusions and surface imperfections for rigid contact lenses. For the purposes of this standard the definitions given in ISO 8320 apply.</p>

36374,IS,,ISO 9342-1:2005,Optics and optical instruments — Test lenses for calibration of focimeters — Part 1: Test lenses for focimeters used for measuring spectacle lenses,Optique et instruments d'optique — Verres étalons pour l'étalonnage des frontofocomètres — Partie 1: Verres étalons pour frontofocomètres pour le mesurage des verres de lunettes,2005-05-04,1,['11.040.70'],ISO/TC 172/SC 7,9599,[17026],"[51054,75925]","['en','fr']",9,<p>ISO 9342-1:2005 specifies requirements for test lenses for the calibration of focimeters that are used for the measurement of spectacle form lenses.</p>

17026,IS,,ISO 9342:1996,Optics and optical instruments — Test lenses for calibration of focimeters,Optique et instruments d'optique — Verres étalons pour l'étalonnage des frontofocomètres,1996-08-22,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[36374],"['en','fr']",5,<p>Specifies requirements for test lenses for the calibration of focimeters.</p>

17027,IS,,ISO 9343:1988,Pliers and nippers — Slip joint pliers — Dimensions and test values,Pinces et tenailles — Pinces réglables à deux positions — Dimensions et valeurs d'essai,1988-08-18,1,['25.140.30'],ISO/TC 29/SC 10,9599,,[33647],"['en','fr']",2,"<p>Specifies the principal dimensions of slip joint pliers, designated as No. 206 in ISO 5742:1982/Add. 1:1985, and the test values in order to verify their aptitude to function in conformity with ISO 5744. The general technical requirements are given in ISO 5743. This pliers illustrated in ISO 9343 are only examples and are not intended to affect the manufaturers' design.</p>"

33647,IS,,ISO 9343:2004,Pliers and nippers — Slip joint pliers — Dimensions and test values,Pinces et tenailles — Pinces réglables à deux positions — Dimensions et valeurs d'essai,2004-09-30,2,['25.140.30'],ISO/TC 29/SC 10,9599,[17027],[79502],"['en','fr']",3,"<p>ISO 9343:2004 specifies the principal dimensions of slip joint pliers, and the test values, in order to verify their aptitude to function in conformity with ISO 5744:2004. The general technical requirements are given in ISO 5743:2004.</p>"

17028,IS,,ISO 9344:1996,Optics and optical instruments — Microscopes — Graticules for eyepieces,Optique et instruments d'optique — Microscopes — Réticules pour oculaires,1996-12-05,1,['37.020'],ISO/TC 172/SC 5,9599,,[51307],"['en','fr']",3,"<p>Gives dimensions and permissible material defects and processing faults of graticules with diameters of 19 mm, 21 mm and 26 mm to be used in microscope eyepieces for the purpose of measurement, assessment and comparison.</p>"

51307,IS,,ISO 9344:2011,Microscopes — Graticules for eyepieces,Microscopes — Réticules pour oculaires,2011-08-04,2,['37.020'],ISO/TC 172/SC 5,9599,[17028],[67549],['en'],3,"<p>ISO 9344:2011 specifies dimensions and permissible material defects and processing faults for graticules with diameters of 19 mm, 21 mm and 26 mm to be used in microscope eyepieces for the purposes of measurement, assessment and comparison.</p>"

17029,IS,,ISO 9345-1:1996,Optics and optical instruments — Microscopes — Imaging distances related to mechanical reference planes — Part 1: Tube length 160 mm,Optique et instruments d'optique — Microscopes — Tirages mécaniques en fonction des plans mécaniques de référence — Partie 1: Tubes de 160 mm de longueur,1996-07-11,1,['37.020'],ISO/TC 172/SC 5,9599,,[61065],"['en','fr']",3,

61065,IS,,ISO 9345-1:2012,Microscopes — Imaging distances related to mechanical reference planes — Part 1: Tube length 160 mm,Microscopes — Tirages mécaniques en fonction des plans mécaniques de référence — Partie 1: Longueur de tubes de 160 mm,2012-06-07,2,['37.020'],ISO/TC 172/SC 5,9599,[17029],[70798],['en'],5,<p>ISO 9345-1:2012 specifies the imaging distances of objectives and eyepieces of microscopes with 160 mm mechanical tube length or equivalent.</p>

30229,IS,,ISO 9345-2:2003,Optics and optical instruments — Microscopes: Imaging distances related to mechanical reference planes — Part 2: Infinity-corrected optical systems,Optique et instruments d'optique — Microscopes — Tirages mécaniques en fonction des plans mécaniques de référence — Partie 2: Systèmes d'optique corrigés à l'infini,2003-03-28,1,['37.020'],ISO/TC 172/SC 5,9599,,[64986],"['en','fr']",8,"<p>ISO 9345-2:2003 specifies the imaging distances of objectives, eyepieces and the focal length of 'normal' tube lenses of microscopes with infinity-corrected optical systems.</p>"

64986,IS,,ISO 9345-2:2014,Microscopes — Imaging distances related to mechanical reference planes — Part 2: Infinity-corrected optical systems,Microscopes — Tirages mécaniques en fonction des plans mécaniques de référence — Partie 2: Systèmes d'optique corrigés à l'infini,2014-09-04,2,['37.020'],ISO/TC 172/SC 5,9599,[30229],[70798],['en'],9,"<p>ISO 9345-2:2014 specifies the imaging distances of objectives, eyepieces and the focal length of 'normal' tube lenses of microscopes with infinity-corrected optical systems.</p>"

17030,IS,,ISO 9346:1987,Thermal insulation — Mass transfer — Physical quantities and definitions,Isolation thermique — Transfert de masse — Grandeurs physiques et définitions,1987-10-22,1,"['01.060','27.220']",ISO/TC 163,9599,,[40550],"['en','fr']",6,"<p>Defines general terms and physical quantities in the field of mass transfer relevant to thermal insulation systems, and gives the corresponding symbols and units.</p>"

21537,IS,Amd,ISO 9346:1987/Amd 1:1996,Thermal insulation — Mass transfer — Physical quantities and definitions — Amendment 1,Isolation thermique — Transfert de masse — Grandeurs physiques et définitions — Amendement 1,1996-02-01,1,"['01.060','27.220']",ISO/TC 163,9599,,[40550],['en'],2,<p>Adds terms of physical quantities and definitions to clause 3.</p>

17032,IS,,ISO 9349:1991,Preinsulated ductile iron pipeline systems,Systèmes de canalisations préisolées en fonte ductile,1991-05-23,1,"['93.025','77.140.75']",ISO/TC 5/SC 2,9599,,[36709],"['en','fr']",18,"<p>Specifies requirements and test methods for buried and above-ground pipeline systems. Includes terms and definitions. Annexes A, B, C and D form an integral part of this standard.</p>"

36709,IS,,ISO 9349:2004,Preinsulated ductile iron pipeline systems,Systèmes de canalisations préisolées en fonte ductile,2004-06-17,2,"['93.025','77.140.75']",ISO/TC 5/SC 2,9599,[17032],[64770],"['en','fr']",6,"<p>ISO 9349:2004 specifies the requirements and test methods applicable to preinsulated ductile iron pipes, fittings, accessories and their joints for the construction of pipelines (or parts thereof) to convey water (e.g. potable water), wastewater and other liquids, to be operated with or without pressure, to be installed below or above ground, to limit temperature variations of the conveyed fluids.</p><p>ISO 9349:2004 gives, in addition to the specifications of the existing ISO stan

17036,IS,,ISO 9352:1989,Plastics — Determination of resistance to wear by abrasive wheels,Plastiques — Détermination de la résistance à l'usure par galets abrasifs,1989-10-12,1,['83.080'],ISO/TC 61/SC 2,9599,,[25171],"['en','fr']",6,

25171,IS,,ISO 9352:1995,Plastics — Determination of resistance to wear by abrasive wheels,Plastiques — Détermination de la résistance à l'usure par galets abrasifs,1995-10-26,2,['83.080.01'],ISO/TC 61/SC 2,9599,[17036],[55507],"['en','fr']",6,"<p>States a general method for determining the resistance to abrasive wear of plastics under the action of abrasive wheels. Equally applicable to moulded test specimens, components and finished products. This method is not applicable to cellular materials or paints.</p>"

17037,IS,,ISO 9353:1991,Glass-reinforced plastics — Preparation of plates with unidirectional reinforcements by bag moulding,Plastiques renforcés au verre textile — Préparation des plaques d'essai à renfort unidirectionnel par moulage au sac,1991-05-16,1,['83.120'],ISO/TC 61/SC 13,9599,,[27246],"['en','fr']",6,

17040,IS,,ISO 9356:1989,Polyolefin pipe assemblies with or without jointed fittings — Resistance to internal pressure — Test method,Assemblages de tubes en polyoléfines comportant ou non des raccords — Résistance à la pression intérieure — Méthode d'essai,1989-12-07,1,['23.040.01'],ISO/TC 138/SC 5,9599,,[24789],"['en','fr']",6,

5355,IS,,ISO 936:1978,Meat and meat products — Determination of ash (Reference method),Viandes et produits à base de viande — Détermination des cendres — (Méthode de référence),1978-12-01,1,['67.120.10'],ISO/TC 34/SC 6,9599,,[24783],"['en','fr']",2,

17044,IS,,ISO 9360:1992,Anaesthetic and respiratory equipment — Heat and moisture exchangers for use in humidifying respired gases in humans,Matériel d'anesthésie et de réanimation respiratoire — Échangeurs de chaleur et d'humidité utilisés pour humidifier les gaz respirés par les êtres humains,1992-09-09,1,['11.040.10'],ISO/TC 121/SC 3,9599,,"[23913,30137]","['en','fr']",9,