Withdrawn and superseded ISO standards — page 181 of 246

44285,IS,,ISO 9073-5:2008,Textiles — Test methods for nonwovens — Part 5: Determination of resistance to mechanical penetration (ball burst procedure),Textiles — Méthodes d'essai pour nontissés — Partie 5: Détermination de la résistance à la pénétration mécanique (méthode d'éclatement à la bille),2008-09-15,1,['59.080.30'],ISO/TC 38,9599,,[87999],"['en','fr']",7,"<p>ISO 9073-5:2008 specifies a method for determining the resistance to mechanical penetration of nonwoven fabrics by a ball of a given diameter.</p><p>The method is primarily designed to be used on nonwovens with some degree of elasticity, for which a regular burst test is not applicable.</p>"

33748,IS,,ISO 9073-6:2000,Textiles — Test methods for nonwovens — Part 6: Absorption,Textiles — Méthodes d'essai pour nontissés — Partie 6: Absorption,2000-12-07,1,['59.080.30'],ISO/TC 38,9599,,[88025],"['en','fr']",9,<p>This part of ISO 9073 describes methods for the evaluation of some aspects of the behaviour of nonwoven fabrics</p><p>in the presence of liquids. In particular:</p><p>_ the liquid absorbency time;</p><p>_ the liquid absorptive capacity;</p><p>_ the liquid wicking rate (capillarity).</p><p>It should be noted that these different aspects of absorbency may relate to various end uses of the tested products.</p><p>The tests are not applicable to any fabric containing super absorb

16657,IS,,ISO 9073-7:1995,Textiles — Test methods for nonwovens — Part 7: Determination of bending length,Textiles — Méthodes d'essai pour nontissés — Partie 7: Détermination de la longueur de flexion,1995-12-27,1,['59.080.30'],ISO/TC 38,9599,,[88393],"['en','fr']",5,<p>Specifies a method for the determination of the bending length of nonwovens. Gives an equation for calculating the flexural rigity of the fabric from the bending length. Does not apply to composites and laminates.</p>

16658,IS,,ISO 9073-8:1995,Textiles — Test methods for nonwovens — Part 8: Determination of liquid strike-through time (simulated urine),Textiles — Méthodes d'essai pour nontissés — Partie 8: Détermination du temps de transpercement des liquides (urine artificielle),1995-12-27,1,['59.080.30'],ISO/TC 38,9599,,[88793],"['en','fr']",4,<p>Provides a method for measuring the time of liquid (simulated urine) strike-through for nonwovens. Does not simulate in-use conditions for finished products.</p>

23471,IS,,ISO 9073-9:1995,Textiles — Test methods for nonwovens — Part 9: Determination of drape coefficient,Textiles — Méthodes d'essai pour nontissés — Partie 9: Détermination du coefficient de drapé,1995-12-27,1,['59.080.30'],ISO/TC 38,9599,,[41375],"['en','fr']",4,<p>Specifies a method for determining the drape coeffizient of nonwovens.</p>

16659,IS,,ISO 9074:1989,Information processing systems — Open Systems Interconnection — Estelle: A formal description technique based on an extended state transition model,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Estelle: Technique de description formelle basée sur un modèle de transition d'état étendu,1989-07-27,1,['35.100.01'],ISO/IEC JTC 1,9599,,[24403],['en'],179,

16660,IS,Amd,ISO 9074:1989/Amd 1:1993,Information processing systems — Open Systems Interconnection — Estelle: A formal description technique based on an extended state transition model — Amendment 1,Systèmes de traitement de l'information — Interconnexion de systèmes ouverts — Estelle: Technique de description formelle basée sur un modèle de transition d'état étendu — Amendement 1,1993-11-18,1,['35.100.01'],ISO/IEC JTC 1,9599,,[24403],['en'],53,

16661,IS,,ISO 9075:1987,Information processing systems — Database language — SQL,Titre manque,1987-06-25,1,['35.060'],ISO/IEC JTC 1,9599,,[16662],,,

45810,IS,,ISO 9076-2:2008,Thermal insulation — Mineral-wool loose-fill for horizontal applications in ventilated roof spaces — Part 2: Principal responsibilities of installers,Isolation thermique — Fibres minérales en vrac pour applications horizontales dans les combles ventilées — Partie 2: Principales responsabilités des installateurs,2008-11-11,1,['91.100.60'],ISO/TC 163/SC 3,9599,,[83958],['en'],12,"<p>ISO 9076-2:2008 specifies the principal responsibilities of the installers of mineral-wool loose-fill thermal insulation products for buildings. A product is manufactured and packaged according to ISO 9076-1 and then installed in ventilated roof spaces as described in ISO 9774 is assured o

28314,IS,,ISO 9080:2003,Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation,Systèmes de canalisations et de gaines en matières plastiques — Détermination de la résistance hydrostatique à long terme des matières thermoplastiques sous forme de tubes par extrapolation,2003-03-13,1,['23.040.20'],ISO/TC 138/SC 5,9599,"[16666,33886]",[43860],"['en','fr']",24,<p>ISO 9080:2003 describes a method for estimating the long-term hydrostatic strength of thermoplastics materials by statistical extrapolation.</p><p>The method is applicable to all types of thermoplastics pipe at applicable temperatures. It was dev

16673,IS,,ISO 9086-1:1987,Wood — Methods of physical and mechanical testing — Vocabulary — Part 1: General concepts and macrostructure,Bois — Méthodes d'essais physiques et mécaniques — Vocabulaire — Partie 1: Généralités et macrostructure,1987-10-29,1,"['79.040','01.040.79']",ISO/TC 218,9599,,[79913],"['en','fr','ru']",7,"<p>Gives terms and definitions relating to physical and mechanical properties of wood. Wood is defined as aggregate of secondary tissues (conductive, mechanical and storing) found in stems, branches and roots of woody plants between the bark and pith.</p>"

16677,IS,,ISO 9089:1989,Marine structures — Mobile offshore units — Anchor winches,Structures maritimes — Unités mobiles au large — Treuils d'ancrage,1989-11-16,1,['47.020.50'],ISO/TC 8/SC 4,9599,,[71444],"['en','fr']",5,"<p>Specifies requirements of anchor winches for position keeping, and temporary and emergency anchoring of mobile offshore units, particularly drill-ships, semi-submersible drilling rigs and accomodation platforms. Does not apply to anchor winches which are used for other purposes.</p>"

16678,IS,,ISO 9090:1989,Gas tightness of equipment for gas welding and allied processes,Étanchéité aux gaz des appareils pour soudage aux gaz et techniques connexes,1989-04-20,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[72739],"['en','fr']",4,"<p>Specifies the maximum external leakage rates which are acceptable for equipment used for welding, cutting and allied processes. Applies to individual components which are used in the gas supply to a blowpipe from the connecting point of the hose (outlet of the cylinder valve or connecting point to a gas supply plant). Does not apply to gas supply plants.</p>"

16681,IS,,ISO 9092:1988,Textiles — Nonwovens — Definition,Textiles — Nontissés — Définition,1988-04-21,1,"['59.080.30','01.040.59']",ISO/TC 38,9599,,[50397],"['en','fr']",2,"<p>Definition nonwoven: A manufactured sheet, web or batt of directionally or randomly orientated fibres, bonded by friction, and/or cohesion and/or adhesion, excluding paper and products which are woven, knitted, tufted, stitch-bonded incorporating binding yarns or filaments, or felted by wet-milling, whether or not additionally needled. The fibres may be of natural or man-made origin.</p>"

50397,IS,,ISO 9092:2011,Textiles — Nonwovens — Definition,Textiles — Nontissés — Définition,2011-09-29,2,"['59.080.30','01.040.59']",ISO/TC 38,9599,[16681],[71369],"['en','fr']",1,<p>ISO 9092:2011 establishes a definition for the term nonwovens.</p>

71369,IS,,ISO 9092:2019,Nonwovens — Vocabulary,Nontissés — Vocabulaire,2019-03-15,3,"['59.080.30','01.040.59']",ISO/TC 38,9599,[50397],[90537],"['en','fr']",3,<p>This document establishes a definition for the term nonwovens and provides auxiliary terminology to distinguish nonwovens from other materials.</p>

16682,IS,,ISO 9093-1:1994,Small craft — Seacocks and through-hull fittings — Part 1: Metallic,Navires de plaisance — Vannes de coque et passe-coques — Partie 1: Construction métallique,1994-12-22,1,['47.080'],ISO/TC 188,9599,,"[75179,72970]","['en','fr']",5,"<p>Specifies requirements for metallic through-hull fittings, seacocks and hose fittings that specifically form part of water intake and discharge lines, and for wet exhaust outlets used in small craft of up to 24 m length of hull. Applies to seacocks and through-hull fittings with cylindrical pipe threads in accordance with ISO 228-1, and with joints for conical pipe threads in accordance with ISO 7-1 with nominal diameters of 1/4, 3/8,

34494,IS,,ISO 9093-2:2002,Small craft — Seacocks and through-hull fittings — Part 2: Non-metallic,Petits navires — Vannes de coque et passe-coques — Partie 2: Construction non métallique,2002-10-22,1,['47.080'],ISO/TC 188,9599,,"[72971,75179]","['en','fr']",8,"<p>ISO 9093-2:2002 specifies requirements for the manufacture and installation of non-metallic through-hull fittings and/or assemblies comprising through-hull fittings, seacocks, hose fittings and/or drain plugs and components attached thereto, used in small craft of up to 24 m length of hull. </p><p>ISO 9093-2:2002 is not applicable to engine exhaust fittings and sail drive through-hull connections.</p>"

34497,IS,,ISO 9094-1:2003,Small craft — Fire protection — Part 1: Craft with a hull length of up to and including 15 m,Petits navires — Protection contre l'incendie — Partie 1: Bateaux d'une longueur de coque inférieure ou égale à 15 m,2003-01-22,1,['47.080'],ISO/TC 188,9599,,"[46551,61729]","['en','fr']",20,"<div id='MathJax_Message' style='display: none;'></div><p>ISO 9094-1:2003 defines procedures to achieve a practical degree of fire protection, specifies portable fire-fighting equipment and sets requirements for fixed fire-fighting systems.</p><p>It applies to small craft of all types with a hull length<em> </em>not exceeding 15 m. For small craft with a hull length greater than 15 m, I

34495,IS,,ISO 9094-2:2002,Small craft — Fire protection — Part 2: Craft with a hull length of over 15 m,Petits navires — Protection contre l'incendie — Partie 2: Bateaux d'une longueur de coque supérieure à 15 m,2002-11-18,1,['47.080'],ISO/TC 188,9599,,"[46551,61729]","['en','fr']",23,"<p>ISO 9094-2:2002 defines procedures to achieve a practical degree of fire protection, specifies portable fire-fighting equipment and sets requirements for fixed fire-fighting systems.</p><p>It applies to small craft of all types with a hull length greater than 15 m and up to and including 24 m</p>"

61729,IS,,ISO 9094:2015,Small craft — Fire protection,Petits navires — Protection contre l'incendie,2015-11-13,1,['47.080'],ISO/TC 188,9599,"[34497,34495]",[78242],"['en','fr']",28,"<p>ISO 9094:2015 defines a practical degree of fire prevention and protection intended to provide enough time for occupants to escape a fire on board small craft.</p><p>It applies to all small craft of up to 24 m length of hull (<i>L</i>_H) except for personal watercraft. </p><p>ISO 9094:2015 excludes:</p><p> the design and installation of those permanently installed galley stoves and heating appliances (including components used to distribute the heat) using fuels that are liquid at atmospheric p

16690,IS,,ISO 9096:1992,Stationary source emissions — Determination of concentration and mass flow rate of particulate material in gas-carrying ducts — Manual gravimetric method,Émissions de sources fixes — Détermination de la concentration et du débit-masse de matières particulaires dans des veines gazeuses — Méthode gravimétrique manuelle,1992-06-04,1,['13.040.40'],ISO/TC 146/SC 1,9599,,[29717],['en'],30,"<p>The method is applicable to moving gas streams in confined spaces such as ducts, chimneys and flues and can be used to determine concentrations ranging from 0,005 g/m^3 to 10 g/m^3. It is primarily a reference method for the determination of particulate matter emitted from stationary s

29717,IS,,ISO 9096:2003,Stationary source emissions — Manual determination of mass concentration of particulate matter,Émissions de sources fixes — Détermination manuelle de la concentration en masse de poussières,2003-02-06,2,['13.040.40'],ISO/TC 146/SC 1,9599,[16690],[70547],"['en','fr']",42,"<p>ISO 9096:2002 describes a reference method for the measurement of particulate matter (dust) concentration in waste gases of concentrations from 20 mg/m³ to 1000 mg/m³ under standard conditions.</p><p>ISO 9096:2002 is applicable to the calibration of automated monitoring systems (AMS). If the emission gas contains unstable, reactive or semi-volatile substances, the measurement

45336,IS,Cor,ISO 9096:2003/Cor 1:2006,Stationary source emissions — Manual determination of mass concentration of particulate matter — Technical Corrigendum 1,Émissions de sources fixes — Détermination manuelle de la concentration en masse de poussières — Rectificatif technique 1,2006-12-01,2,['13.040.40'],ISO/TC 146/SC 1,9599,,[70547],"['en','fr']",1,

16692,IS,,ISO 9098-1:1994,Bunk beds for domestic use — Safety requirements and tests — Part 1: Safety requirements,Lits superposés pour usage domestique — Spécifications de sécurité et essais — Partie 1: Spécifications de sécurité,1994-11-03,1,['97.140'],ISO/TC 136,9599,,[80976],"['en','fr']",3,"<p>Lays down requirements relating to the safety of bunk beds for domestic use. Intended to minimize the risk of accidents happening to children. Only the sleeping function is considered. Also applies to single beds for use at a height of the bed base of 800 mm or more above floor level, irrespective of the use to which the space below is put.</p>"

16693,IS,,ISO 9098-2:1994,Bunk beds for domestic use — Safety requirements and tests — Part 2: Test methods,Lits superposés pour usage domestique — Spécifications de sécurité et essais — Partie 2: Méthodes d'essai,1994-11-03,1,['97.140'],ISO/TC 136,9599,,[80977],"['en','fr']",9,"<p>Specifies test methods to assess the safety of bunk beds for domestic use. Also applies to single beds for use at a height of the bed base of 800 mm or more above floor level, irrespective of the use to which the space below is put. The tests consist of the application, to various parts of the bunk bed, of loads or forces simulating normal functional use, as well as misuse that can reasonably be expected to occur.

16694,IS,,ISO 9099:1987,Air-conditioning and ventilation of dry provision rooms on board ships — Design conditions and basis of calculations,Conditionnement d'air et ventilation des cambuses à bord des navires — Conditions de conception et bases de calcul,1987-04-02,1,['47.020.90'],ISO/TC 8/SC 3,9599,,[76611],"['en','fr']",2,<p>Applies to seagoing merchant ships and for all conditions except those encountered in extremely hot climates. Is fundamentally based on ISO 7547 which shall be available when applying this Standard.</p>

3748,IS,,ISO 91-1:1982,Petroleum measurement tables — Part 1: Tables based on reference temperatures of 15 degrees C and 60 degrees F,Tables de mesure du pétrole — Partie 1: Tables basées sur les températures de référence de 15 degrés C et 60 degrés F,1982-02-01,1,['75.180.30'],ISO/TC 28/SC 2,9599,[3746],[3749],"['en','fr']",3,

3749,IS,,ISO 91-1:1992,Petroleum measurement tables — Part 1: Tables based on reference temperatures of 15 degrees C and 60 degrees F,Tables de mesure du pétrole — Partie 1: Tables basées sur les températures de référence de 15 degrés C et 60 degrés F,1992-11-12,2,['75.180.30'],ISO/TC 28/SC 2,9599,[3748],[65049],"['en','fr']",6,"<p>IS0 91-1:1992 refers to petroleum measurement tables published by the American Petroleum Institute (API, USA), the American Society for Testing and Materials (ASTM, USA) and the Institute of Petroleum (IP, UK) and subsidiary documents, correcting the printing errors in these publications, based on reference temperatures of 15 °C and 60 °F.</p><p>The standard refer

3750,IS,,ISO 91-2:1991,Petroleum measurement tables — Part 2: Tables based on a reference temperature of 20 degrees C,Tables de mesurage du pétrole — Partie 2: Tables basées sur la température de référence de 20 degrés C,1991-11-14,1,['75.180.30'],ISO/TC 28/SC 2,9599,,[65049],"['en','fr']",3,<p>Refers to computer implementation procedures for the correction of densities and volumes to the reference temperature of 20°C. This first edition cancels and replaces ISO/TR 91:1970/Add.1:1975. Annex A is for information only.</p>

16695,IS,,ISO 9100:1992,Wide-mouth glass containers — Vacuum lug finishes — Dimensions,Récipients en verre à col large — Bagues à crans (bouchage sous vide) — Dimensions,1992-11-12,1,['55.100'],ISO/TC 63,9599,,"[37706,37713,37707,37714,37715,37716,37708,37709,37710,37711,37703,37712,37704,37705]","['en','fr']",5,<p>All untoleranced dimensions specified are nominal. The glass thickness throughout the full depth of the finish shall be adequate to withstand normal handling. The finish shall be free from cracks likely to have an adverse effect on sealing performance.</p>

16697,IS,,ISO 9102:1990,"Road vehicles — Compression-ignition engines — Screw-in injection nozzle holders, types 24, 25 and 26","Véhicules routiers — Moteurs à combustion interne à allumage par compression — Porte-injecteurs vissés, types 24, 25 et 26",1990-07-05,1,['43.060.40'],ISO/TC 22,9599,,[26746],"['en','fr']",4,

16699,IS,,ISO 9104:1991,Measurement of fluid flow in closed conduits — Methods of evaluating the performance of electromagnetic flow-meters for liquids,Mesure de débit des fluides dans les conduites fermées — Méthodes d'évaluation de la performance des débitmètres électromagnétiques utilisés pour les liquides,1991-04-11,1,['17.120.10'],ISO/TC 30/SC 5,9599,,[68092],"['en','fr']",18,<p>The methods specified are intended for use by manufacturers to determine the performance of their products and by users to verify manufacturer's performance specifications. The test conditions represent those which commonly arise during use. The values specified herein should be used where no other values are sp

16704,IS,,ISO 9110-1:1990,Hydraulic fluid power — Measurement techniques — Part 1: General measurement principles,Transmissions hydrauliques — Techniques de mesurage — Partie 1: Principes généraux de mesurage,1990-10-11,1,['23.100.01'],ISO/TC 131/SC 8,9599,,[73716],"['en','fr']",4,<p>Establishes general principles for the measurement of performance parameters under static or steady-state conditions. Describes practical requirements for assessing the capability of the measuring system and hence the level of accuracy of measurement.</p>

16705,IS,,ISO 9110-2:1990,Hydraulic fluid power — Measurement techniques — Part 2: Measurement of average steady-state pressure in a closed conduit,Transmissions hydrauliques — Techniques de mesurage — Partie 2: Mesurage de la pression moyenne dans un conduit fermé en régime permanent,1990-10-11,1,['23.100.01'],ISO/TC 131/SC 8,9599,,[73715],"['en','fr']",6,"<p>Establishes procedures for measuring the average steady-state pressure in a hydraulic fluid power conduit. Applies to the measurement in closed conduits with inside diameters greater than 3 mm, transmitting hydraulic fluid with velocities less than 25 m/s and pressures less than 70 MPa.</p>"

16706,IS,,ISO 9112:1991,Truck and bus tyres — Method of measuring tyre rolling circumference — Loaded new tyres,Pneumatiques pour véhicules utilitaires et autobus — Méthode de mesure de la circonférence de roulement — Pneumatiques neufs en charge,1991-01-31,1,['83.160.10'],ISO/TC 31/SC 4,9599,,[45652],"['en','fr']",3,<p>Applies to all truck and bus tyres. Specifies methods for measuring rolling circumference and revolutions per unit distance (kilometre). The values thus obtained are not intended for use as levels of performance or quality.</p>

16708,IS,,ISO 9113:1986,Plastics — Polypropylene (PP) and propylene-copolymer thermoplastics — Determination of isotactic index,Plastiques — Thermoplastiques à base de polypropylène (PP) et de copolymères de propylène — Détermination de l'indice d'isotacticité,1986-10-09,1,['83.080.20'],ISO/TC 61/SC 9,9599,,"[70408,16707]","['en','fr']",3,"<p>Specifies a method for determining the percentage of matter which can be extracted from crystalline propylene plastics by boiling n-heptane under standard conditions of testing. A powdered test portion is carefully dried, weighed and extracted in as Soxhlet-apparatus with n-heptane during 24 h. The mass of residue of the test portion is determined and a

16711,IS,,ISO 9116:1992,Green coffee — Guidance on methods of specification,Café vert — Guide sur les méthodes de spécification,1992-04-09,1,['67.140.20'],ISO/TC 34/SC 15,9599,,[39373],"['en','fr']",3,"<p>Gives guidance on methods to be used to describe green coffee for sale and purchase and is based on the terms of contract used in the international coffee trade. It also recommends procedures for sampling, packing, marking, storage and shipping of green coffee. It applies to green coffee as defined in ISO 3509.</p>"

39373,IS,,ISO 9116:2004,Green coffee — Guidelines on methods of specification,Café vert — Lignes directrices sur les méthodes de spécification,2004-11-23,2,['67.140.20'],ISO/TC 34/SC 15,9599,[16711],[87698],['en'],4,"<p>ISO 9116:2004 gives guidance on methods to be used to describe green coffee for sale and purchase, and is based on the terms of contract used in the international coffee trade.</p><p>It also recommends procedures for sampling, packing, marking, storage and shipping of green coffee.</p><p>It is applicable to green coffee as defined in ISO 3509.</p>"

16712,IS,,ISO 9117:1990,Paints and varnishes — Determination of through-dry state and through-dry time — Method of test,Peintures et vernis — Détermination du séchage à coeur et du temps de séchage à coeur — Méthode d'essai,1990-04-05,1,['87.040'],ISO/TC 35/SC 9,9599,,"[52011,44472]","['en','fr']",5,

29455,IS,,ISO 9123:2001,Measurement of liquid flow in open channels — Stage-fall-discharge relationships,Mesure de débit des liquides dans les canaux découverts — Relations hauteur-chute-débit,2001-11-22,1,['17.120.20'],ISO/TC 113/SC 1,9599,[16720],[66300],['en'],14,

16721,IS,,ISO 9125:1990,Fibre-cement slates and fittings,Ardoises et leurs accessoires en fibres-ciment,1990-11-29,1,['91.100.40'],ISO/TC 77,9599,,[45792],"['en','fr']",9,"<p>Specifies the characteristics and establishes methods of control and test as well as acceptance conditions for fibre-cement slates and their fittings, for use mainly as roofing and cladding materials, which are not covered by ISO 395. Applies to slates not exceeding 600 mm x 600 mm.</p>"

37631,IS,Amd,ISO 9125:1990/Amd 1:2004,Fibre-cement slates and fittings — Amendment 1,Ardoises et leurs accessoires en fibres-ciment — Amendement 1,2004-08-23,1,['91.100.40'],ISO/TC 77,9599,,[45792],"['en','fr']",7,

21828,IS,Cor,ISO 9125:1990/Cor 1:1993,Fibre-cement slates and fittings — Technical Corrigendum 1,Ardoises et leurs accessoires en fibres-ciment — Rectificatif technique 1,1993-02-18,1,['91.100.40'],ISO/TC 77,9599,,[45792],"['en','fr']",1,"<p>Replaces the second sentence of subclause 3.5.2.3 as follows: The tube is filled with water and maintained at a height of about 250 mm measured from the upper surface of the test piece, and the level is maintained constant.</p>"

42282,IS,Cor,ISO 9125:1990/Cor 2:2005,Fibre-cement slates and fittings — Technical Corrigendum 2,Ardoises et leurs accessoires en fibres-ciment — Rectificatif technique 2,2005-06-02,1,['91.100.40'],ISO/TC 77,9599,,[45792],"['en','fr']",1,

16723,IS,,ISO 9127:1988,Information processing systems — User documentation and cover information for consumer software packages,Systèmes de traitement de l'information — Documentation pour l'utilisateur et renseignements sur l'emballage des progiciels grand public,1988-09-01,1,['35.080'],ISO/IEC JTC 1/SC 7,9599,,"[37463,43073]","['en','fr']",7,"<p>Describes user documentation and cover information supplied with software packages. Is applicable to software packages sold off-the-shelf to consumers for business, scientific, educational and home use. References: ISO 6592; ISO 7185.</p>"

16724,IS,,ISO 9128:1987,Road vehicles — Graphical symbols to designate brake fluid types,Véhicules routiers — Symboles graphiques pour la désignation des types de liquides de frein,1987-11-19,1,"['75.120','01.080.20','43.040.40']",ISO/TC 22,9599,,"[36951,40459]","['en','fr']",3,"<p>Specifies the graphical symbols and colours used to identify, on road vehicles, the correct type of fluid to be used for: petroleum-base brake fluid systems; non-petroleum-base brake fluid systems. The same symbols are also used for labelling the fluid containers (ISO 3871). Non-petroleum-base fluids (ISO 4925, glycol type) and petroleum-base fluids (ISO 7308) are totally incompatible, requiring the use of differe

16725,IS,,ISO 9129:1988,Motorcycles — Measurement methods for moments of inertia,Motocycles — Méthodes de mesure des moments d'inertie,1988-12-29,1,['43.140'],ISO/TC 22,9599,,"[42939,35088]","['en','fr']",6,<p>Specifies a measuring method for determining the moments of inertia of the motorcycle and of the motorcycle/rider combination. Applies to two-wheeled motorcycles. Other measuring methods can be used if it is demonstrated that the results are equivalent. Some figures illustrate shapes and reference quantities of concern.</p>

16726,IS,,ISO 9130:1989,Motorcycles — Measurement method for location of centre of gravity,Motocycles — Méthode de mesure de l'emplacement du centre de gravité,1989-05-18,1,['43.140'],ISO/TC 22,9599,,[33494],"['en','fr']",6,<p>Specifies a measuring method for determining the location of the centre of gravity of the motorcycle and of the motorcycle/rider combination. Applies to two-wheeled motorcycles. Other measuring methods can be used if it is demonstrated that the results are equivalent. Some figures illustrate shapes and reference quantities of concern.</p>

16732,IS,,ISO 9136:1989,Abrasive macrograins — Determination of bulk density,Macrograins abrasifs — Détermination de la masse volumique apparente,1989-11-30,1,['25.100.70'],ISO/TC 29/SC 5,9599,,[36545],"['en','fr']",3,"<p>Applies to the bulk density of bounded and coated abrasive macrograins. Defines the term 'bulk density of abrasive macrograins', and gives apparatus, calibration of the measuring cylinder, method of measurement and expression of results.</p>"

16734,IS,,ISO 9138:1993,Abrasive grains — Sampling and splitting,Grains abrasifs — Échantillonnage et division,1993-01-28,1,['25.100.70'],ISO/TC 29/SC 5,9599,,"[33698,60012]","['en','fr']",2,<p>Sampling is made using a sampling thief. Splitting means dividing into two equal portions using a splitter (commonly a Jones sampler) and repeating this procedure at each of the portions obtained until the sample is 25 % larger than the amount required for testing. The method may be used in the comparative testing of uniformly produced abrasive grains.</p>

16735,IS,,ISO 9139:1998,"Aerospace — Nuts, plain or slotted (castellated) — Procurement specification",Aéronautique et espace — Écrous ordinaires ou à créneaux — Spécification d'approvisionnement,1998-12-17,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[88087],"['en','fr']",18,"<p>This International Standard specifies the required characteristics for metric plain or slotted (castellated) nuts, with MJ threads according to ISO 5855-2, for use in aerospace construction. </p><p>It is applicable to nuts as defined above, provided that reference is made to this International Standard in the relevant definition document.</p>"

16739,IS,,ISO 9142:1990,Adhesives — Guide to the selection of standard laboratory ageing conditions for testing bonded joints,Adhésifs — Guide pour la sélection de conditions normales d'essai de vieillissement en laboratoire des assemblages collés,1990-12-06,1,['83.180'],ISO/TC 61/SC 11,9599,,"[36282,26827]","['en','fr']",20,"<p>Describes conditions under which adhesive joints may be exposed to various climatic or chemical influences for the purpose of assessing the effects of such influences on certain properties. They are not necessarily applicable to the determination of the service life of a bonded assembly. The principle consists in defining the ageing conditions that relate most closel

26714,IS,Cor,ISO 9142:1990/Cor 1:1995,Adhesives — Guide to the selection of standard laboratory ageing conditions for testing bonded joints — Technical Corrigendum 1,Adhésifs — Guide pour la sélection de conditions normales d'essai de vieillissement en laboratoire des assemblages collés — Rectificatif technique 1,1995-12-07,1,['83.180'],ISO/TC 61/SC 11,9599,,[36282],"['en','fr']",1,<p>Corrects the content of some subclauses.</p>

16745,IS,,ISO 9148:1987,Composition cork in rolls for decoration — Test methods,Rouleaux d'aggloméré composé de liège pour décoration — Méthodes d'essai,1987-10-08,1,['79.100'],ISO/TC 87,9599,,[52196],"['en','fr']",2,"<p>Specifies the following characteristics: dimensions, tensile strength, flexibility, moisture content, and resistance to boilding water. In general apparatus and procedure are similar to those described in ISO 7322. Dimensions (or masses) and the number of test pieces are indicated in a table.</p>"

16746,IS,,ISO 9149:1987,Composition cork in rolls for decoration — Specifications,Rouleaux d'aggloméré composé de liège pour décoration — Spécifications,1987-08-27,1,['79.100'],ISO/TC 87,9599,,[52197],"['en','fr']",1,"<p>Specifies dimensions and their permissible deviations, tensile strength, flexibility, moisture content, and resistance to boilding water for materials tested in accordance with ISO 9148. Fixes the kind of packaging and related marking.</p>"

16748,IS,,ISO 9151:1995,Protective clothing against heat and flame — Determination of heat transmission on exposure to flame,Vêtements de protection contre la chaleur et les flammes — Détermination de la transmission de chaleur à l'exposition d'une flamme,1995-05-11,1,['13.340.10'],ISO/TC 94/SC 13,9599,,[55326],"['en','fr']",9,"<p>Specifies a method for comparing the heat transmission through materials or material assemblies used in protective clothing. Materials are ranked by calculation of a heat transfer index, which is an indication of the relative heat transmission under the specified test conditions. The heat transfer index should not be taken as a measure of the protection time given

16751,IS,,ISO 9154:1999,"Aerospace — Bolts, with MJ threads, made of heat-resistant nickel-based alloy, strength class 1 550 MPa — Procurement specification","Aéronautique et espace — Vis à filetage MJ, en alliage résistant à chaud à base de nickel, classe de résistance 1 550 MPa — Spécification d'approvisionnement",1999-12-16,1,['49.030.20'],ISO/TC 20/SC 4,9599,,[68579],"['en','fr']",26,

16753,IS,,ISO 9156:1989,"Aerospace — Nuts, anchor, self-locking, fixed, 90 degrees corner, reduced series, with counterbore, with MJ threads, coated or uncoated, classification 1 100 MPa/235 degrees C, 1 100 MPa/315 degrees C or 1 100 MPa/425 degrees C — Dimensions","Aéronautique et espace — Écrous à river, à freinage interne, à filetage MJ, fixes, d'angle 90 degrés, série réduite, avec chambrage, revêtus ou non revêtus, de classification 1 100 MPa/235 degrés C, 1 100 MPa/315 degrés C ou 1 100 MPa/425 degrés C — Dimensions",1989-10-19,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[27436],"['en','fr']",2,

16754,IS,,ISO 9157:1988,"Aerospace — Nuts, spline-drive, self-locking, with MJ threads, coated or uncoated, classification 1 100 MPa/650 degrees C, 1 250 MPa/760 degrees C, 1 550 MPa/235 degrees C or 1 550 MPa/650 degrees C — Dimensions","Aéronautique et espace — Écrous cannelés à freinage interne, à filetage MJ, revêtus ou non revêtus, de classification 1 100 MPa/650 degrés C, 1 250 MPa/760 degrés C, 1 550 MPa/235 degrés C ou 1 550 MPa/650 degrés C — Dimensions",1988-12-29,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[31733],"['en','fr']",2,"<p>The values laid down herein have been specified so as to satisfy the requirements laid down in ISO 5858 or ISO 8641 (depending on the classification of the

31742,IS,,ISO 9161:2004,Uranium dioxide powder — Determination of apparent density and tap density,Poudre de dioxyde d'uranium — Détermination de la masse volumique apparente et de la masse volumique après tassement,2004-08-25,1,['27.120.30'],ISO/TC 85/SC 5,9599,,[68616],"['en','fr']",6,"<p>ISO 9161:2004 specifies a method of determining the apparent density and tap density of free-flowing uranium dioxide (UO₂) powder which will be used for pelleting and sintering of UO₂ pellets as a nuclear fuel.</p><p>The method specified by ISO 9161:2004 can be used for different UO₂ powder types including grains, granules, spheres or other kinds of particles. The method c

16759,IS,,ISO 9162:1989,Petroleum products — Fuels (class F) — Liquefied petroleum gases — Specifications,Produits pétroliers — Combustibles (classe F) — Gaz de pétrole liquéfiés — Spécifications,1989-11-02,1,['75.160.30'],ISO/TC 28/SC 4,9599,,[37164],"['en','fr']",6,"<p>Gives required characteristics and additional information to be supplied to the purchaser by the vendor of these products and is intended to apply to international transfers of commercial propane and butane. Is neither intended nor expected to replace or encroach upon national standards of any country, since seach country is subjected to different regulations, codes, industry practice and market utilization.</p>"

16760,IS,,ISO 9163:1996,Textile glass — Rovings — Manufacture of test specimens and determination of tensile strength of impregnated rovings,Verre textile — Stratifils — Fabrication d'éprouvettes et essai de traction sur stratifil imprégné,1996-10-10,1,['59.100.10'],ISO/TC 61/SC 13,9599,,[36288],"['en','fr']",12,

16763,IS,,ISO 9167-1:1992,Rapeseed — Determination of glucosinolates content — Part 1: Method using high-performance liquid chromatography,Graines de colza — Dosage des glucosinolates — Partie 1: Méthode par chromatographie liquide à haute performance,1992-07-02,1,['67.200.20'],ISO/TC 34/SC 2,9599,,"[29790,41809,72207]","['en','fr']",9,"<p>The method specified is based on extraction by methanol, purification and enzymatic desulfatation, determination using reversed-phase chromatography. Does not determine glucosinolates which are substituted on the glucose molecule. A rapid method for the determination of glucosinolates content using X-ray fluorescence spectrometry is the subject of ISO 9167

61350,IS,Amd,ISO 9167-1:1992/Amd 1:2013,Rapeseed — Determination of glucosinolates content — Part 1: Method using high-performance liquid chromatography — Amendment 1,Graines de colza — Dosage des glucosinolates — Partie 1: Méthode par chromatographie liquide à haute performance — Amendement 1,2013-07-04,1,['67.200.20'],ISO/TC 34/SC 2,9599,,[72207],"['en','fr']",1,

16765,IS,,ISO 9168:1988,Dental handpieces — Hose connectors,Pièces à main dentaires — Connexions,1988-03-24,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[16766],,,

16766,IS,,ISO 9168:1991,Dental handpieces — Hose connectors,Pièces à main dentaires — Connexions,1991-08-29,2,['11.060.20'],ISO/TC 106/SC 4,9599,[16765],[46572],"['en','fr']",6,"<p>Specifies four types of standard connectors. Type A: connector with two or three outlets; Type B: connector with four or five outlets; Type C: connector with four outlets and electrical contacts; Type D: connector with three outlets and connection thread M12 x 0,5.</p>"

16767,IS,,ISO 9169:1994,Air quality — Determination of performance characteristics of measurement methods,Qualité de l'air — Détermination des caractéristiques de performance des méthodes de mesurage,1994-11-03,1,['13.040.01'],ISO/TC 146/SC 4,9599,,[31496],"['en','fr']",18,"<p>Specifies procedures to quantify the performance characteristics of air quality measurement methods defined in ISO 6879: bias, calibration function and linearity, instability, lower detection limit, period of unattended operation, selectivity, sensitivity, upper limit of measurement. The procedures given are applicable only to air quality measurement methods with linear continuous calibration functions, the output vari

5326,IS,,ISO 917:1974,Testing of refrigerant compressors,Essais des compresseurs pour fluides frigorigènes,1974-09-01,1,['27.200'],ISO/TC 86,9599,,[5327],"['en','fr']",28,

5327,IS,,ISO 917:1989,Testing of refrigerant compressors,Essais des compresseurs pour fluides frigorigènes,1989-08-31,2,['27.200'],ISO/TC 86/SC 4,9599,[5326],"[85541,22686,53762]","['en','fr']",31,"<p>The provisions are applicable to single-stage refrigerant compressors of the positive-displacement type only. Selected test methods are described for the determination of the refrigerating capacity, power, isentropric efficiency, and the coefficient of performance. The test methods described may also be used as a guide for testing other types of refrigerant compressors. - Replaces the first edition (ISO 917:1974) and constitutes its technical revision.</p>"

26351,IS,,ISO 9170-1:1999,Terminal units for medical gas pipeline systems — Part 1: Terminal units for use with compressed medical gases and vacuum,Prises murales pour réseaux de distribution de gaz médicaux — Partie 1: Prises murales pour les gaz médicaux comprimés et le vide,1999-12-16,1,['11.040.10'],ISO/TC 121/SC 6,9599,[16768],[42055],['en'],16,

42055,IS,,ISO 9170-1:2008,Terminal units for medical gas pipeline systems — Part 1: Terminal units for use with compressed medical gases and vacuum,Prises murales pour systèmes de distribution de gaz médicaux — Partie 1: Prises murales pour les gaz médicaux comprimés et le vide,2008-06-16,2,['11.040.10'],ISO/TC 121/SC 6,9599,[26351],[67451],"['en','fr','ru']",20,"<div id='MathJax_Message' style='display: none;'></div><p>ISO 9170-1:2008 applies to:</p><ol><li>terminal units intended for use in medical gas pipeline systems in accordance with ISO 7396-1, for use with the following medical gases:<ul><li>oxygen,</li><li>nitrous oxide;</li><li>medical air;</li><li>carbon dioxide;</li><li>oxygen/ni

16768,IS,,ISO 9170:1990,Terminal units for use in medical gas pipeline systems,Prises murales utilisées dans des réseaux de distribution de gaz médicaux,1990-10-11,1,['11.040.10'],ISO/TC 121/SC 6,9599,,"[26351,27252]","['en','fr']",15,

27252,IS,,ISO 9170-2:1999,Terminal units for medical gas pipeline systems — Part 2: Terminal units for anaesthetic gas scavenging systems,Prises murales pour réseaux de distribution de gaz médicaux — Partie 2: Prises murales pour systèmes d'évacuation des gaz d'anesthésie,1999-12-16,1,['11.040.10'],ISO/TC 121/SC 6,9599,[16768],[42056],['en'],17,

16775,IS,,ISO 9173-1:1991,Dental extraction forceps — Part 1: Screw and pin joint types,Daviers à usage dentaire — Partie 1: Types d'articulations à vis ou à tourillon,1991-07-11,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[34694],"['en','fr']",18,<p>Specifies the dimensions and performance requirements. Describes test methods. Many figures illustrate the performance shapes. Annexes A and B are for information only.</p>

34694,IS,,ISO 9173-1:2006,Dentistry — Extraction forceps — Part 1: General requirements and test methods,Art dentaire — Daviers — Partie 1: Exigences générales et méthodes d'essai,2006-06-09,2,['11.060.20'],ISO/TC 106/SC 4,9599,[16775],[65160],"['en','fr']",4,<p>ISO 9173-1:2006 specifies the general performance requirements for extraction forceps used in dentistry.</p>

16777,IS,,ISO 9174:1990,Water quality — Determination of total chromium — Atomic absorption spectrometric methods,Qualité de l'eau — Dosage du chrome total — Méthodes par spectrométrie d'absorption atomique,1990-04-19,1,['13.060.50'],ISO/TC 147/SC 2,9599,,[28636],['en'],6,

16781,IS,,ISO 9177-1:1989,"Mechanical pencils — Part 1: Classification, dimensions, performance requirements and testing","Porte-mine — Partie 1: Classification, dimensions, caractéristiques de fonctionnement et essais",1989-03-16,1,"['01.100.40','97.180']",ISO/TC 10,9599,,[57586],"['en','fr']",6,

57586,IS,,ISO 9177-1:2011,"Mechanical pencils — Part 1: Classification, dimensions, performance requirements and testing","Porte-mine — Partie 1: Classification, dimensions, caractéristiques de fonctionnement et essais",2011-11-07,2,"['01.100.40','97.180']",ISO/TC 10,9599,[16781],[69128],['en'],7,

16782,IS,,ISO 9177-2:1989,Mechanical pencils — Part 2: Black leads — Classification and dimensions,Porte-mine — Partie 2: Mines graphite — Classification et dimensions,1989-03-16,1,"['01.100.40','97.180']",ISO/TC 10,9599,,[83353],"['en','fr']",2,"<p>Two types are available, black leads in which the binding agent is an organic polymer (designated by the letter 'P'), and black leads in which the binding agent is clay (designated by the letter 'C'). Classification is made according to the degree of hardness. Part 1 deals with the classification, dimensions, performance requirements and testing.</p>"

20426,IS,,ISO 9177-3:1994,Mechanical pencils — Part 3: Black leads — Bending strengths of HB leads,Porte-mine — Partie 3: Mines graphite — Résistance à la flexion des mines HB,1994-06-30,1,"['01.100.40','97.180']",ISO/TC 10,9599,,[83354],"['en','fr']",3,<p>Specifies bending strengths and a test method for black leads of HB hardness degree used for mechanical pencils for technical drawings.</p>

16788,IS,,ISO 9181:1990,Tools for pressing — Round punches with 60 degrees conical head and reduced shank,Outillage de presse — Poinçons ronds à tête conique à 60 degrés et à corps épaulé,1990-11-15,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[44036],"['en','fr']",3,"<p>Specifies the dimensions and tolerances for round punches having shank diameters of 2 mm or 3 mm. Gives examples of materials and hardness, and specifies the designation of punches.</p>"

16789,IS,,ISO 9182-1:1992,Tools for pressing — Guide pillars — Part 1: Types,Outillage de presse — Colonnes de guidage — Partie 1: Types,1992-06-18,1,['25.120.10'],ISO/TC 29/SC 8,9599,,"[60718,29907]","['en','fr']",2,<p>Illustrates four main types of guide pillars and their methods of mounting.</p>

60718,IS,,ISO 9182-1:2013,Tools for pressing — Guide pillars — Part 1: Types,Outillage de presse — Colonnes de guidage — Partie 1: Types,2013-12-11,2,['25.120.10'],ISO/TC 29/SC 8,9599,[16789],[83520],"['en','fr']",2,<p>ISO 9182-1:2013 illustrates four main types of guide pillars and their methods of mounting.</p>

16790,IS,,ISO 9182-2:1992,"Tools for pressing — Guide pillars — Part 2: Type A, straight pillars","Outillage de presse — Colonnes de guidage — Partie 2: Type A, colonnes droites",1992-06-18,1,['25.120.10'],ISO/TC 29/SC 8,9599,,"[60719,29908]","['en','fr']",4,"<p>Specifies the dimensions and tolerances, gives guidance on materials, and specifies the hardness and the designation. Those guide pillars may be of type A1, straight, or of type A2, straight with end-locking and locking ring.</p>"

60719,IS,,ISO 9182-2:2013,"Tools for pressing — Guide pillars — Part 2: Type A, straight pillars","Outillage de presse — Colonnes de guidage — Partie 2: Type A, colonnes droites",2013-12-11,2,['25.120.10'],ISO/TC 29/SC 8,9599,[16790],[83521],"['en','fr']",4,"<p>ISO 9182-2;2013 specifies the dimensions and tolerances, in millimetres, of guide pillars, type A, intended for use in press tools. These guide pillars can be straight, type A1, or straight with end-locking and locking ring, type A2. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet its requirements.</p>"

16791,IS,,ISO 9182-3:1992,"Tools for pressing — Guide pillars — Part 3: Type B, end-locking pillars","Outillage de presse — Colonnes de guidage — Partie 3: Type B, colonnes à retenue inférieure",1992-06-18,1,['25.120.10'],ISO/TC 29/SC 8,9599,,"[29909,60720]","['en','fr']",4,"<p>Specifies the dimensions and tolerances, gives guidance on materials, and specifies the hardness and the designation. Those guide pillars may be of type B1, end-locking, or type B2, end-locking with lubrication grooves.</p>"

60720,IS,,ISO 9182-3:2013,"Tools for pressing — Guide pillars — Part 3: Type B, end-locking pillars","Outillage de presse — Colonnes de guidage — Partie 3: Type B, colonnes à retenue inférieure",2013-12-11,2,['25.120.10'],ISO/TC 29/SC 8,9599,[16791],[79118],"['en','fr']",4,"<p>ISO 9182-3:2013 specifies the dimensions and tolerances, in millimetres, of guide pillars, type B, intended for use in press tools. These guide pillars can be end-locking, type B1, or end-locking with lubrication grooves, type B2. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet its requirements.</p>"

79118,IS,,ISO 9182-3:2020,"Tools for pressing — Guide pillars — Part 3: Type B, end-locking pillars","Outillage de presse — Colonnes de guidage — Partie 3: Type B, colonnes à retenue inférieure",2020-09-08,3,['25.120.10'],ISO/TC 29/SC 8,9599,[60720],[83522],"['en','fr']",4,"<p>This document specifies the dimensions and tolerances of guide pillars, type B, intended for use in press tools. These guide pillars can be end-locking, type B1 (see Figure 1), or end-locking with lubrication grooves, type B2 (see Figure 2).</p><p>It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this document.</p>"

16792,IS,,ISO 9182-4:1992,"Tools for pressing — Guide pillars — Part 4: Type C, pillars with taper lead and bush","Outillage de presse — Colonnes de guidage — Partie 4: Type C, colonnes à emmanchement conique et sa bague de guidage",1992-06-18,1,['25.120.10'],ISO/TC 29/SC 8,9599,,"[60721,29910]","['en','fr']",4,"<p>Specifies the dimensions and tolerances, gives guidance on materials, and specifies the hardness and the designation.</p>"

60721,IS,,ISO 9182-4:2013,"Tools for pressing — Guide pillars — Part 4: Type C, pillars with taper lead and bush","Outillage de presse — Colonnes de guidage — Partie 4: Type C, colonnes à emmanchement conique et sa bague de guidage",2013-12-11,2,['25.120.10'],ISO/TC 29/SC 8,9599,[16792],[79119],"['en','fr']",5,"<p>ISO 9182-4:2013 specifies the dimensions and tolerances, in millimetres, of guide pillars, type C, with taper lead and bush, intended for use in press tools. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet its requirements.</p>"

79119,IS,,ISO 9182-4:2020,"Tools for pressing — Guide pillars — Part 4: Type C, pillars with taper lead and bush","Outillage de presse — Colonnes de guidage — Partie 4: Type C, colonnes à emmanchement conique et sa bague de guidage",2020-09-08,3,['25.120.10'],ISO/TC 29/SC 8,9599,[60721],[83523],"['en','fr']",5,"<p>This document specifies the dimensions and tolerances of guide pillars, type C, with taper lead and bush, intended for use in press tools.</p><p>It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this document.</p>"

16793,IS,,ISO 9182-5:1992,"Tools for pressing — Guide pillars — Part 5: Type D, end-locking pillars with flange","Outillage de presse — Colonnes de guidage — Partie 5: Type D, colonnes à retenue inférieure, démontables",1992-06-18,1,['25.120.10'],ISO/TC 29/SC 8,9599,,"[60722,29911]","['en','fr']",4,"<p>Specifies the dimensions and tolerances, gives guidance on materials, and specifies the hardness and the designation.</p>"

60722,IS,,ISO 9182-5:2013,"Tools for pressing — Guide pillars — Part 5: Type D, end-locking pillars with flange","Outillage de presse — Colonnes de guidage — Partie 5: Type D, colonnes à retenue inférieure, démontables",2013-12-11,2,['25.120.10'],ISO/TC 29/SC 8,9599,[16793],[79120],"['en','fr']",5,"<p>ISO 9182-5:2013 specifies the dimensions and tolerances, in millimetres, of guide pillars, type D, end-locking pillar with flange, intended for use in press tools. It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet its requirements.</p>"

79120,IS,,ISO 9182-5:2020,"Tools for pressing — Guide pillars — Part 5: Type D, end-locking pillars with flange","Outillage de presse — Colonnes de guidage — Partie 5: Type D, colonnes à retenue inférieure, démontables",2020-09-08,3,['25.120.10'],ISO/TC 29/SC 8,9599,[60722],[83524],"['en','fr']",5,"<p>This document specifies the dimensions and tolerances of guide pillars, type D, end-locking pillar with flange, intended for use in press tools.</p><p>It gives guidance on the materials and specifies the hardness and the designation of guide pillars which meet the requirements of this document.</p>"

16800,IS,,ISO 9183-1:1990,Tools for pressing — Wear plates for press dies — Part 1: Type A,Outillage de presse — Plaques de frottement — Partie 1: Type A,1990-11-22,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[41580],"['en','fr']",4,"<p>Specifies the basic dimensions and tolerances of wear for press dies as well as the size and positions of the clearance holes for attachment. Gives two thicknesses: 20 mm, type A1; 25 mm, type A2.</p>"

16801,IS,,ISO 9183-2:1993,Tools for pressing — Wear plates for press dies — Part 2: Type B,Outillage de presse — Plaques de frottement — Partie 2: Type B,1993-07-22,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[57875],"['en','fr']",4,"<p>Specifies the basic dimensions and tolerances, in millimetres, for wear plates, type B, intended for use mainly in large presses. Also specifies the size and positions of the clearance holes for attachment. Gives guidance on the materials and hardness and specifies the designation of wear plates, type B.</p>"

16802,IS,,ISO 9184-1:1990,"Paper, board and pulps — Fibre furnish analysis — Part 1: General method","Papier, carton et pâtes — Détermination de la composition fibreuse — Partie 1: Méthode générale",1990-12-06,1,"['85.060','85.040']",ISO/TC 6,9599,,[79506],"['en','fr']",7,"<p>This part specifies the general performance of the test for fibre furnish analysis. It is applicable to all kinds of pulps and to most papers and boards, including those containing more than one kind of fibre, taking into account different pulping processes. This method is less suitable for heavily impregnated or highly coloured papers and boards. The standard describes in detail: principle, reagents, apparatus, prepara

16809,IS,,ISO 9185:1990,Protective clothing — Assessment of resistance of materials to molten metal splash,Vêtements de protection — Évaluation de la résistance des matériaux à la projection de métal fondu,1990-06-28,1,['13.340.10'],ISO/TC 94/SC 13,9599,,[41479],"['en','fr']",9,

41479,IS,,ISO 9185:2007,Protective clothing — Assessment of resistance of materials to molten metal splash,Vêtements de protection — Évaluation de la résistance des matériaux aux projections de métal fondu,2007-06-14,2,['13.340.10'],ISO/TC 94/SC 13,9599,[16809],[85806],"['en','fr']",12,"<p>ISO 9185:2007 specifies a method for assessing the heat penetration resistance of materials intended for use in clothing to protect against large splashes of molten metal. It provides specific procedures for assessing the effects of splashes of molten aluminium, molten cryolite, molten copper, molten iron and molten mild steel. The principle of the test method is applicable to a wider range of hot molten m