Withdrawn and superseded ISO standards — page 157 of 246

13927,IS,,ISO 7270:1987,Rubber — Identification of polymers (single polymers and blends) — Pyrolytic gas chromatographic method,Caoutchouc — Identification des polymères (un seul polymère ou mélanges de polymères) — Méthode par pyrolyse et chromatographie en phase gazeuse,1987-10-22,1,['83.060'],ISO/TC 45,9599,[11518],[33761],"['en','fr']",4,"<p>Describes three methods for the different materials. The methods may also be applicable to other types of polymers than given in the standard, but this must be verified by the analyst in each particular case.</p>"

38581,IS,,ISO 7270-2:2005,Rubber — Analysis by pyrolytic gas-chromatographic methods — Part 2: Determination of styrene/butadiene/isoprene ratio,Caoutchouc — Méthodes d'analyse par pyrolyse et chromatographie en phase gazeuse — Partie 2: Détermination du rapport styrène/butadiène/isoprène,2005-03-21,1,['83.060'],ISO/TC 45/SC 2,9599,,[53025],"['en','fr']",9,"<p>ISO 7270-1:2005 specifies the principles and procedures for determining, by pyrolysis and subsequent gas chromatography, the styrene (STY)/butadiene (BD)/isoprene (IP) ratio in copolymers, or blends of homopolymers and/or copolymers, in raw rubbers or vulcanized or unvulcanized compounds.</p><p>It is applicable to copolymers/terpolymer

53025,IS,,ISO 7270-2:2012,Rubber — Analysis by pyrolytic gas-chromatographic methods — Part 2: Determination of styrene/butadiene/isoprene ratio,Caoutchouc — Méthodes d'analyse par pyrolyse et chromatographie en phase gazeuse — Partie 2: Détermination du rapport styrène/butadiène/isoprène,2012-09-13,2,['83.060'],ISO/TC 45/SC 2,9599,[38581],[88778],"['en','fr']",11,"<p>ISO 7270-2:2012 specifies a pyrolytic gas-chromatographic method for the determination of the styrene/butadiene/isoprene ratio in copolymers, or blends of homopolymers and/or copolymers, in raw rubbers or in unvulcanized or vulcanized compounds. It is applicable to copolymers/terpolymers consisting of styrene, butadiene and iso

13928,IS,,ISO 7271:1982,Aluminium and aluminium alloys — Foil and thin strip — Dimensional tolerances,Aluminium et alliages d'aluminium — Feuilles et bandes minces — Tolérances dimensionnelles,1982-07-01,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[53665],"['en','fr']",2,"<p>ISO 7271 specifies thickness tolerances and width tolerances for foils and thin strips, shipped in rolls, for general purposes. It is applicable firstly to double-rolled foil, with one side matt and the other bright, and of thicknesses in the range 6 m to 50 m inclusive and secondly to single-rolled foil and thin strip, with both sides the same, and of thicknesses in the range 21 m to 200 m.</p>"

13930,IS,,ISO 7272:1993,Photography — Paper dimensions — Paper for documentary reproduction,Photographie — Dimensions des papiers — Papiers pour reproduction de documents,1993-10-14,1,"['37.040.20','37.100.20']",ISO/TC 42,9599,,[13929],"['en','fr']",8,

13931,IS,,ISO 7273:1981,Wrought aluminium and aluminium alloys — Extruded round bars — Tolerances on shape and dimensions,Aluminium et alliages d'aluminium corroyés — Barres rondes filées — Tolérances sur forme et dimensions,1981-09-01,1,['77.150.10'],ISO/TC 79/SC 6,9599,,[12686],"['en','fr']",1,

13935,IS,,ISO 7278-2:1988,Liquid hydrocarbons — Dynamic measurement — Proving systems for volumetric meters — Part 2: Pipe provers,Hydrocarbures liquides — Mesurage dynamique — Systèmes d'étalonnage des compteurs volumétriques — Partie 2: Tubes étalons,1988-12-29,1,['75.180.30'],ISO/TC 28/SC 2,9599,,[81588],"['en','fr']",18,"<p>Provides guidance for the design, installation and calibration of these provers. Calculation techniques for use when calibrating and operating provers are detailed in ISO 4267-2. Most of the material is general in that it applies to provers for use with different liquids and types of meters and for proving them in different services. Does not apply to the newer 'small

13936,IS,,ISO 7278-3:1986,Liquid hydrocarbons — Dynamic measurement — Proving systems for volumetric meters — Part 3: Pulse interpolation techniques,Hydrocarbures liquides — Mesurage dynamique — Systèmes d'étalonnage pour compteurs volumétriques — Partie 3: Techniques d'interpolation des impulsions,1986-06-12,1,['75.180.30'],ISO/TC 28/SC 2,9599,,[13937],"['en','fr']",8,

13938,IS,,ISO 7278-4:1999,Liquid hydrocarbons — Dynamic measurement — Proving systems for volumetric meters — Part 4: Guide for operators of pipe provers,Hydrocarbures liquides — Mesurage dynamique — Systèmes d'étalonnage des compteurs volumétriques — Partie 4: Manuel de référence pour les opérateurs de tubes étalons,1999-04-22,1,['75.180.30'],ISO/TC 28/SC 2,9599,,"[81588,51452,62262]","['en','fr']",27,

4963,IS,,ISO 728:1981,Coke (nominal top size greater than 20 mm) — Size analysis,Coke (dimension supérieure nominale supérieure à 20 mm) — Analyse granulométrique,1981-11-01,2,['75.160.10'],ISO/TC 27/SC 3,9599,,[4964],"['en','fr']",3,

4964,IS,,ISO 728:1995,Coke (nominal top size greater than 20 mm) — Size analysis by sieving,Coke (dimension supérieure nominale supérieure à 20 mm) — Analyse granulométrique par tamisage,1995-10-19,3,['75.160.10'],ISO/TC 27/SC 3,9599,[4963],[78696],['en'],4,"<p>Specifies a method for the size analysis of coke, of nominal top size greater than 20 mm, by manual sieving.</p>"

13942,IS,,ISO 7284:1984,"Resistance welding equipment — Particular specifications applicable to transformers with two separate secondary windings for multi-spot welding, as used in the automobile industry","Matériel de soudage par résistance — Spécifications particulières applicables aux transformateurs à deux enroulements secondaires séparés pour soudage multipoints, utilisés dans l'industrie automobile",1984-12-01,1,['25.160.30'],ISO/TC 44/SC 6,9599,,[13943],"['en','fr']",8,

13946,IS,,ISO 7287:1992,Graphical symbols for thermal cutting equipment,Symboles graphiques pour équipements de coupage thermique,1992-05-14,1,"['01.080.20','25.160.30']",ISO/TC 44/SC 8,9599,,[31768],"['en','fr']",13,"<p>The graphical symbols (a referent and an alphabetical index of the referents are given) are to be placed on equipment, e.g. indicators and operator controls, in order to instruct the persons handling as to its use and operation. Annex A gives examples of the use of symbols on an operating board for a control system for oxygen cutting machines.</p>"

13948,IS,,ISO 7289:1990,"Quick-action couplings with shut-off valve for welding, cutting and allied processes","Raccords rapides à obturation pour équipements pour soudage, coupage et techniques connexes",1990-11-08,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[24624],"['en','fr']",6,

24624,IS,,ISO 7289:1996,"Quick-action couplings with shut-off valves for gas welding, cutting and allied processes","Raccords rapides à obturation pour équipements pour soudage au gaz, coupage et techniques connexes",1996-08-15,2,['25.160.30'],ISO/TC 44/SC 8,9599,[13948],[44986],"['en','fr']",7,<p>Gives the specifications and the type tests for quick action couplings with shut-off valves. It does apply to quick-action couplings used between the regulator and the torch in gas welding and cutting equipment. Replaces the first edition.</p>

44986,IS,,ISO 7289:2010,"Gas welding equipment — Quick-action couplings with shut-off valves for welding, cutting and allied processes","Matériel de soudage aux gaz — Raccords rapides à obturation pour soudage, coupage et techniques connexes",2010-01-28,3,['25.160.30'],ISO/TC 44/SC 8,9599,[24624],[71170],"['en','fr','ru']",10,"<p>ISO 7289:2010 defines the specifications and the type tests for quick-action couplings with shut-off valves. It applies to quick-action couplings used between the regulator and the torch in equipment for gas welding, cutting and allied processes.</p><p>ISO 7289:2010 applies to cases where these couplings are used with hoses in accordance with ISO 3821 or threaded un

4965,IS,,ISO 729:1985,Oilseeds — Determination of acidity of oils,Graines oléagineuses — Détermination de l'acidité de l'huile,1985-10-24,1,['67.200.20'],ISO/TC 34/SC 2,9599,,[4966],"['en','fr']",,

13950,IS,,ISO 7291:1990,"Welding, cutting and allied processes — Manifold regulators","Soudage, coupage et techniques connexes — Détendeurs des centrales de bouteilles (de gaz industriels)",1990-11-01,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[26486],"['en','fr']",8,

26486,IS,,ISO 7291:1999,"Gas welding equipment — Pressure regulators for manifold systems used in welding, cutting and allied processes up to 300 bar","Matériel de soudage aux gaz — Détendeurs de centrales de bouteilles pour le soudage, le coupage et les techniques connexes jusqu'à 300 bar",1999-12-09,2,['25.160.30'],ISO/TC 44/SC 8,9599,[13950],[44967],"['en','fr']",17,

13951,IS,,ISO 7292:1997,"Flowmeter regulators used on cylinders for welding, cutting and allied processes — Classification and specifications","Détendeurs avec débitmètres utilisés sur les bouteilles pour le soudage, le coupage et les techniques connexes — Classification et spécifications",1997-03-27,1,['25.160.30'],ISO/TC 44/SC 8,9599,,[40644],"['en','fr']",5,

13952,IS,,ISO 7293:1983,Forestry machinery — Portable chain saws — Engine performance and fuel consumption,Machines forestières — Scies à chaîne portatives — Puissance et consommation du moteur,1983-04-01,1,['65.060.80'],ISO/TC 23/SC 17,9599,,[25973],"['en','fr']",3,

25973,IS,,ISO 7293:1997,Forestry machinery — Portable chain saws — Engine performance and fuel consumption,Machines forestières — Scies à chaîne portatives — Puissance et consommation de carburant du moteur,1997-12-18,2,['65.060.80'],ISO/TC 23/SC 17,9599,[13952],[79635],"['en','fr']",5,

79635,IS,,ISO 7293:2021,Forestry machinery — Portable chain-saws — Engine performance and fuel consumption,Machines forestières — Scies à chaîne portatives — Puissance et consommation de carburant du moteur,2021-10-22,3,['65.060.80'],ISO/TC 23/SC 17,9599,[25973],[86335],"['en','fr']",6,<p>This document specifies a method for testing the performance and fuel consumption of internal combustion engines used to power portable chain-saws.</p>

13954,IS,,ISO 7295:1982,Tyre valves — Aircraft — Interchangeability dimensions,Valves pour pneumatiques d'aéronefs — Dimensions d'interchangeabilité,1982-11-01,1,['83.160.20'],ISO/TC 31/SC 9,9599,,[13955],"['en','fr']",8,

24511,IS,,ISO 7296-2:1996,Cranes — Graphical symbols — Part 2: Mobile cranes,Appareils de levage à charge suspendue — Symboles graphiques — Partie 2: Grues mobiles,1996-12-26,1,"['01.080.20','53.020.20']",ISO/TC 96/SC 6,9599,,[75608],"['en','fr']",31,<p>Contains graphical symbols for use on operator controls and other displays on mobile cranes as defined in ISO 4306-2.</p>

41465,IS,,ISO 7299-1:2007,Diesel engines — End-mounting flanges for pumps — Part 1: Fuel injection pumps,Moteurs diesels — Brides de montage des pompes — Partie 1: Pompes d'injection de carburant,2007-01-10,1,['43.060.40'],ISO/TC 22/SC 34,9599,[25065],[86547],['en'],10,"<p>ISO 7299-1:2006 specifies dimensional requirements for nine types of end-mounting flanges for fuel injection pumps (rotary, distributor and in-line fuel injection pumps) for use in diesel (compression-ignition) engines.</p>"

13961,IS,,ISO 7299:1984,Road vehicles — End-mounting flanges for fuel injection pumps,Véhicules routiers — Brides de montage pour pompes d'injection,1984-11-01,1,['43.060.40'],ISO/TC 22,9599,,[25065],"['en','fr']",9,

25065,IS,,ISO 7299:1996,Diesel engines — End-mounting flanges for fuel injection pumps,Moteurs diesels — Brides de montage des pompes d'injection de combustible,1996-05-09,2,['43.060.40'],ISO/TC 22,9599,[13961],"[41465,41467]","['en','fr']",10,<p>Specifies dimensional requirements for four types of end-mounting flange for distributor fuel injection pumps and five types of end mounting flange for in-line fuel injection pumps. Replaces the first edition.</p>

41467,IS,,ISO 7299-2:2009,Diesel engines — End-mounting flanges for pumps — Part 2: High-pressure supply pumps for common rail fuel injection systems,Moteurs diesels — Brides de montage des pompes — Partie 2: Pompes d'alimentation à haute pression pour systèmes d'injection de combustible à rampe commune,2009-01-29,1,['43.060.40'],ISO/TC 22/SC 34,9599,[25065],[77053],['en'],9,<p>ISO 7299-2:2009 specifies dimensional requirements for seven types of end-mounting flanges of high-pressure supply pumps for common rail fuel injection systems for use in diesel (compression-ignition) engines.</p>

4967,IS,,ISO 730-1:1977,"Agricultural wheeled tractors — Three-point linkage — Part 1: Categories 1, 2 and 3","Tracteurs agricoles à roues — Attelage trois points — Partie 1: Catégories 1, 2 et 3",1977-04-01,1,['65.060.10'],ISO/TC 23/SC 4,9599,,"[4968,4969]","['en','fr']",8,

4968,IS,,ISO 730-1:1990,"Agricultural wheeled tractors — Rear-mounted three-point linkage — Part 1: Categories 1, 2 and 3","Tracteurs agricoles à roues — Attelage trois points monté à l'arrière — Partie 1: Catégories 1, 2 et 3",1990-03-08,2,['65.060.10'],ISO/TC 23/SC 4,9599,[4967],[4969],"['en','fr']",6,

4969,IS,,ISO 730-1:1994,"Agricultural wheeled tractors — Rear-mounted three-point linkage — Part 1: Categories 1, 2, 3 and 4","Tracteurs agricoles à roues — Attelage trois points monté à l'arrière — Partie 1: Catégories 1, 2, 3 et 4",1994-12-22,3,['65.060.10'],ISO/TC 23/SC 4,9599,"[4971,4967,4968]",[41233],"['en','fr']",12,<p>Cancels and replaces the second edition (ISO 730-1 (1990) and ISO 730-3 (1982)). Describes the dimensions and requirements of the three-point linkage for the attachment of implements or equipment to the rear of agricultural wheeled tractors. Specifies four categories to be used on different ranges of agricultural tractors.</p>

25953,IS,Cor,ISO 730-1:1994/Cor 1:1995,"Agricultural wheeled tractors — Rear-mounted three-point linkage — Part 1: Categories 1, 2, 3 and 4 — Technical Corrigendum 1","Tracteurs agricoles à roues — Attelage trois points monté à l'arrière — Partie 1: Catégories 1, 2, 3 et 4 — Rectificatif technique 1",1995-06-08,3,['65.060.10'],ISO/TC 23/SC 4,9599,,[41233],"['en','fr']",1,"<p>Replaces on page 7, in table 3, in column category 2 a numerical value.</p>"

4970,IS,,ISO 730-2:1979,Agricultural wheeled tractors — Three-point linkage — Part 2: Category 1 N (Narrow hitch),Tracteurs agricoles à roues — Attelage trois points — Partie 2: Catégorie 1 N (Attelage étroit),1979-05-01,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[41233],"['en','fr']",4,"<p>Specifies the requirements for the attachment of implements or equipment to the rear narrow tractors by means of a hitch in association with a power lift. Applies to tractors with a maximum power at the drawbar up to 35 kW. Contains three figures which illustrate dimensions and configurations, and includes three tables showing dimensions in millimetres.</p>"

4971,IS,,ISO 730-3:1982,Agricultural wheeled tractors — Three-point linkage — Part 3: Category 4,Tracteurs agricoles à roues — Attelage trois points — Partie 3: Catégorie 4,1982-06-01,1,['65.060.10'],ISO/TC 23/SC 4,9599,,[4969],"['en','fr']",4,

13963,IS,,ISO 7301:1988,Rice — Specification,Riz — Spécifications,1988-10-06,1,['67.060'],ISO/TC 34/SC 4,9599,,[24553],"['en','fr']",12,"<p>Definitons of relevant terms, then specification of general, organoleptic, health, physical and chemical characteristics;further description of sampling, of test methods, of packaging and marking. A normative annex specifies the determination of extraneous matter, broken kernels, defective kernels and other kinds of rice.</p>"

24553,IS,,ISO 7301:2002,Rice — Specification,Riz — Spécifications,2002-05-30,2,['67.060'],ISO/TC 34/SC 4,9599,[13963],[50935],"['en','fr']",17,

50935,IS,,ISO 7301:2011,Rice — Specification,Riz — Spécifications,2011-02-17,3,['67.060'],ISO/TC 34/SC 4,9599,[24553],[73411],"['en','fr','ru']",19,"<p>ISO 7301:2011 gives the minimum specifications for rice (<i>Oryza sativa </i>L.) which is subject to international trade. It is applicable to the following types: husked rice and milled rice, parboiled or not, intended for direct human consumption. It is neither applicable to other products derived from rice, nor to waxy rice (glutinous rice).</p>"

13964,IS,,ISO 7302:1982,Cereals and cereal products — Determination of total fat content,Céréales et produits céréaliers — Détermination de la teneur en matières grasses totales,1982-11-01,1,['67.060'],ISO/TC 34/SC 4,9599,,[38428],"['en','fr']",3,"<p>The method consists in hydroyzing of a test portion by hydrochloric acid in the presence of ethanol and formic acid, after any grinding required, then extracting of the fat by hexane in a special flask, removing of the solvent and weighing the residue thus obtained.</p>"

44312,IS,,ISO 7304-1:2016,Durum wheat semolina and alimentary pasta — Estimation of cooking quality of alimentary pasta by sensory analysis — Part 1: Reference method,Semoule de blé dur et pâtes alimentaires — Appréciation de la qualité de cuisson par analyse sensorielle — Partie 1: Méthode de référence,2016-03-08,1,['67.060'],ISO/TC 34/SC 4,9599,[13966],[89196],"['en','fr']",9,"<p>ISO 7304-1:2016 sets out a method for estimation by sensory analysis of the cooking quality of alimentary pasta. Estimation takes place through the evaluation of the following:</p><p>- firmness, by chewing;</p><p>- liveliness, by manual handling;</p><p>- starch release, by manual handling.</p><p>The

13966,IS,,ISO 7304:1985,Durum wheat semolinas and alimentary pasta — Estimation of cooking quality of spaghetti by sensory analysis,Semoules de blé dur et pâtes alimentaires — Appréciation de la qualité culinaire des spaghetti par analyse sensorielle,1985-04-25,1,['67.060'],ISO/TC 34/SC 4,9599,,"[38250,44312]","['en','fr']",10,<p>The method consists in determining of a minimum cooking time and calculation of two experimental cooking times for each sample. Sensory analysis of at most six samples presented in pairs to a panel of at least six qualified assessors. Classification and scoring of the samples according to their surface condition and firmness. An annex gives examples of arrangements

13967,IS,,ISO 7305:1986,Milled cereal products — Determination of fat acidity,Produits de mouture des céréales — Détermination de l'acidité grasse,1986-03-13,1,['67.060'],ISO/TC 34/SC 4,9599,,[13968],"['en','fr']",3,

13968,IS,,ISO 7305:1998,Milled cereal products — Determination of fat acidity,Produits de mouture des céréales — Détermination de l'acidité grasse,1998-07-16,2,['67.060'],ISO/TC 34/SC 4,9599,[13967],[70009],"['en','fr']",7,

13973,IS,,ISO 7310:1984,Road vehicles — Compression ignition engines — Heads for spin-on fuel filters with horizontal flange — Mounting and connecting dimensions,Véhicules routiers — Moteurs à combustion interne à allumage par compression — Têtes pour filtres à combustible vissés à bride horizontale — Dimensions de montage et de raccordement,1984-12-01,1,['43.060.40'],ISO/TC 22,9599,,[13974],"['en','fr']",6,

13975,IS,,ISO 7311:1984,Road vehicles — Compression ignition engines — Heads for fuel filters with vertical flange — Mounting and connecting dimensions,Véhicules routiers — Moteurs à combustion interne à allumage par compression — Têtes pour filtres à combustible à bride verticale — Dimensions de montage et de raccordement,1984-12-01,1,['43.060.40'],ISO/TC 22,9599,,[13976],"['en','fr']",8,

13979,IS,,ISO 7313:1984,Aircraft — High temperature convoluted hose assemblies in polytetrafluoroethylene (PTFE),"Aéronefs — Tuyauterie flexible, haute température, convolutée, en polytétrafluoréthylène (PTFE)",1984-03-01,1,"['83.140.40','49.080']",ISO/TC 20/SC 10,9599,,"[13980,68320]","['en','fr']",8,"<p>Gives characteristics of these assemblies for use in aircraft fluid systems at temperatures between -55 and +200 °C and at nominal pressures, depending on bore size, up to 6,8 MPa. Special approval from the proper national authority may be required it these hoses are to be part of a pressurized gas storage system. Two types of hose assembly are covered: Typ 1 - non-conductive inner tube and

13981,IS,,ISO 7314:1989,"Aerospace — Fluid systems — Hose assembly, metal",Aéronautique et espace — Systèmes de fluides — Tuyauteries flexibles métalliques,1989-11-09,1,['49.080'],ISO/TC 20/SC 10,9599,,[13982],"['en','fr']",12,

13982,IS,,ISO 7314:1994,"Aerospace — Fluid systems — Hose assembly, metal",Aéronautique et espace — Systèmes de fluides — Tuyauteries flexibles métalliques,1994-09-29,2,['49.080'],ISO/TC 20/SC 10,9599,[13981],[27050],"['en','fr']",12,"<p>Cancels and replaces the first edition (1989). Gives specifications for medium pressure, high temperature, flexible metal hose assemblies suitable for continuous operation in liquid and pneumatic systems from -55 °C to +400 °C, with short duration excursions up to +650 °C. Intended for use to convey air and gases in pneumatic systems, bleed air systems, heating and ventilating systems, and instrument air systems. Does not cover flow velocity in such assembli

13983,IS,,ISO 7315:1985,Aerospace — 'P' clamps (loop clamps) for fluid tubing installations — Dimensions,Aéronautique et espace — Colliers de fixation en P pour tuyauteries de fluides — Dimensions,1985-11-07,1,['49.080'],ISO/TC 20/SC 10,9599,,[13984],"['en','fr']",,

13988,IS,,ISO 7319:1982,Aerospace construction — Fluid systems — Interface of metric couplings,Constructions aérospatiales — Systèmes hydrauliques — Interface des raccordements métriques,1982-12-01,1,['49.080'],ISO/TC 20/SC 10,9599,,[13989],"['en','fr']",3,

13989,IS,,ISO 7319:1992,Aerospace — Fluid systems — Interface of 24 degree cone metric couplings,Aéronautique et espace — Systèmes de fluides — Interface des raccordements métriques à cône de 24 degrés,1992-11-25,2,['49.080'],ISO/TC 20/SC 10,9599,[13988],[79990],"['en','fr']",4,<p>Defines the geometry of the interface of couplings for fluid systems in aircrafts. Specifies the dimensions which allow the interchangeability of the male and female elements and of the nut used for the connection. The dimensions define the maximum volume of the male fitting.</p>

4979,IS,,ISO 732:1982,"Photography — Dimensions for 127, 120 and 620 roll film, backing paper and film spools","Photographie — Dimensions des pellicules, du papier protecteur et des bobines pour les formats 127, 120 et 620",1982-12-01,2,['37.040.20'],ISO/TC 42,9599,,[4980],"['en','fr']",9,

4980,IS,,ISO 732:1991,Photography — Film dimensions — 120 and 220 sizes,Photographie — Dimensions des films — Rouleaux de pellicule 120 et 220,1991-07-11,3,['37.040.20'],ISO/TC 42,9599,[4979],[29302],"['en','fr']",8,

13990,IS,,ISO 7320:1985,"Aerospace — Fluid systems port connection, seal and fitting end — Dimensions","Aéronautique et espace — Orifice fileté de raccordement, joint et élément à filetage extérieur dans les systèmes de fluides — Dimensions",1985-09-19,1,['49.080'],ISO/TC 20/SC 10,9599,,[13991],"['en','fr']",4,

13991,IS,,ISO 7320:1992,"Aerospace — Couplings, threaded and sealed, for fluid systems — Dimensions",Aéronautique et espace — Raccordement fileté étanche pour les systèmes de fluides — Dimensions,1992-12-03,2,['49.080'],ISO/TC 20/SC 10,9599,[13990],[80017],"['en','fr']",7,"<p>Establishes a system for sealing the port connection of couplings. Specifies dimensions to achieve interchangeability of the port connection, the fitting end and a seal. The seal may be a standard O-ring or a special ring.</p>"

13993,IS,,ISO 7322:1986,Cork — Composition cork — Test methods,Liège — Aggloméré composé — Méthodes d'essai,1986-04-03,1,['79.100'],ISO/TC 87,9599,,[28113],"['en','fr']",3,

28113,IS,,ISO 7322:2000,Composition cork — Test methods,Aggloméré composé de liège — Méthodes d'essai,2000-03-23,2,['79.100'],ISO/TC 87,9599,[13993],[62402],"['en','fr']",7,

13994,IS,,ISO 7323:1985,"Rubber, raw and unvulcanized compounded — Determination of plasticity number and recovery number — Parallel plate method",Caoutchouc brut et mélanges non vulcanisés — Détermination de l'indice de plasticité et de l'indice de recouvrance — Méthode des plateaux parallèles,1985-08-15,1,"['83.060','83.040.10']",ISO/TC 45/SC 2,9599,,[43675],"['en','fr']",3,<p>Describes the method using the parallel plate plastometer and gives the definition of the plasticity number and recovery number. Two figures show the typical parallel plate plastometer and hardened steel die for forming the test piece.</p>

38012,IS,Cor,ISO 7323:1985/Cor 1:2003,"Rubber, raw and unvulcanized compounded — Determination of plasticity number and recovery number — Parallel plate method — Technical Corrigendum 1",Caoutchouc brut et mélanges non vulcanisés — Détermination de l'indice de plasticité et de l'indice de recouvrance — Méthode des plateaux parallèles — Rectificatif technique 1,2003-02-24,1,"['83.060','83.040.10']",ISO/TC 45/SC 2,9599,,[43675],"['en','fr']",2,

14000,IS,,ISO 7326:1984,Rubber and plastics hoses — Assessment of ozone resistance under static conditions,Tuyaux en caoutchouc et en plastique — Évaluation de la résistance à l'ozone dans des conditions statiques,1984-12-01,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[14001],"['en','fr']",4,

14001,IS,,ISO 7326:1991,Rubber and plastics hoses — Assessment of ozone resistance under static conditions,Tuyaux en caoutchouc et en plastique — Évaluation de la résistance à l'ozone dans des conditions statiques,1991-02-07,2,['23.040.70'],ISO/TC 45/SC 1,9599,[14000],"[20163,40963]","['en','fr']",4,"<p>This second edition cancels and replaces the first edition (ISO 7326 :1984), clause 1 of which has been technically revised. Specifies three methods. The results of tests carried out in accordance with method 1 may not be comparable with the results obtained when tests are carried out in accordance with methods 2 and 3. For hoses with built-in fittings from which it is not possible to take te

40963,IS,,ISO 7326:2006,Rubber and plastics hoses — Assessment of ozone resistance under static conditions,Tuyaux en caoutchouc et en plastique — Évaluation de la résistance à l'ozone dans des conditions statiques,2006-10-06,3,['23.040.70'],ISO/TC 45/SC 1,9599,[14001],[68053],"['en','fr']",7,"<p>ISO 7326:2006 specifies five methods for determining the ozone resistance of the outer covers of hoses:</p><ul><li>method 1, for bore sizes up to and including 25 mm, carried out on the hose itself;</li><li>method 2, for bore sizes greater than 25 mm, carried out on a test piece from the hose wall;</li><li>method 3, for bore sizes greater than 25 mm, carried out on a test piece from the cover;</li><l

14004,IS,,ISO 7328:1984,Milk-based edible ices and ice-mixes — Determination of fat content — Roese-Gottlieb gravimetric method (Reference method),Glaces de consommation et préparations pour glaces à base de lait — Détermination de la teneur en matière grasse — Méthode gravimétrique Roese-Gottlieb (Méthode de référence),1984-11-01,1,['67.100.40'],ISO/TC 34/SC 5,9599,,[27797],"['en','fr']",8,

27797,IS,,ISO 7328:1999,Milk-based edible ices and ice mixes — Determination of fat content — Gravimetric method (Reference method),Glaces de consommation et préparations pour glaces à base de lait — Détermination de la teneur en matière grasse — Méthode gravimétrique (Méthode de référence),1999-12-02,2,['67.100.40'],ISO/TC 34/SC 5,9599,[14004],[51015],"['en','fr']",14,

51015,IS,,ISO 7328:2008,Milk-based edible ices and ice mixes — Determination of fat content — Gravimetric method (Reference method),Glaces de consommation et préparations pour glaces à base de lait — Détermination de la teneur en matière grasse — Méthode gravimétrique (Méthode de référence),2008-10-02,3,['67.100.40'],ISO/TC 34/SC 5,9599,[27797],[75226],"['en','fr']",15,"<p>ISO 7328¦IDF 116:2008 specifies the reference method for the determination of the fat content of most milk-based edible ices and ice mixes.</p><p>The method is also applicable to concentrated and dried ice mixes.</p><p>The method is not applicable to some milk-based edible ices and ice mixes, in which the level of emulsifi

14006,IS,,ISO 7330:1988,Photography — 110-size cartridges — Location and dimensions of film exposure and film identification notches,Photographie — Chargeurs de format 110 — Emplacement et dimensions des encoches d'exposition et d'identification du film,1988-07-21,1,['37.040.20'],ISO/TC 42,9599,,[22024],"['en','fr']",8,

14007,IS,,ISO 7331:1983,Ski-poles for alpine skiing — Safety requirements and test methods,Bâtons de skis alpins — Exigences de sécurité et méthodes d'essai,1983-11-01,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[14008],"['en','fr']",11,

14008,IS,,ISO 7331:1990,Ski-poles for alpine skiing — Safety requirements and test methods,Bâtons de skis alpins — Prescriptions de sécurité et méthodes d'essai,1990-02-22,2,['97.220.20'],ISO/TC 83/SC 4,9599,[14007],[38624],"['en','fr']",11,"<p>Specifies the minimum requirements for safety in ski-poles for alpine skiing and gives test methods to check conformity with these requirements. Applies to ski-poles (excluding special designs) in the following ranges of nominal length l: group A: l 1100 mm (adults poles), group B: 1100 mm &gt; l 700 mm (junior poles) and group C: l &lt; 900 mm (childrens toy-poles).</p>"

38624,IS,,ISO 7331:2005,Ski-poles for alpine skiing — Requirements and test methods,Bâtons de skis alpins — Exigences et méthodes d'essai,2005-07-29,3,['97.220.20'],ISO/TC 83/SC 4,9599,[14008],[55819],"['en','fr']",17,"<p>ISO 7331:2005 specifies the minimum requirements for safety in ski-poles for alpine skiing and gives test methods to check conformity with these requirements.</p><p>It applies to ski-poles for alpine skiing in the following ranges of total length:</p><ul><li> group A, equal to or great er than 1 050 mm (adults' poles);</li><li> group B, less than 1 050 mm but equal to or greater than 700 mm (junior poles);</li><li> group C, equal to or less than 700 mm (children's toy-poles

55819,IS,,ISO 7331:2011,Ski-poles for alpine skiing — Requirements and test methods,Bâtons de skis alpins — Exigences et méthodes d'essai,2011-07-01,4,['97.220.20'],ISO/TC 83/SC 4,9599,[38624],[76871],"['en','fr']",17,"<p>ISO 7331:2011 defines the minimum requirements for safety in ski-poles for alpine skiing and specifies test methods to check conformity with these requirements.</p><p>Special designs may deviate from ISO 7331:2011, but shall be marked in a durable manner as special designs.</p>"

14009,IS,,ISO 7332:1983,"Metric fasteners for aerospace construction — Nuts, anchor, self-locking, floating, two-lug, reduced series, with counterbore — Strength classification 1 100 MPa — Maximum operating temperature 235 degrees C","Éléments de fixation métriques pour les constructions aérospatiales — Écrous à river, à freinage interne, flottants, double patte, série réduite, avec chambrage — Classe de résistance 1 100 MPa — Température maximale d'utilisation 235 degrés C",1983-08-01,1,['49.030.30'],ISO/TC 20/SC 4,9599,,[14010],"['en','fr']",3,

26835,IS,,ISO 734-1:1998,Oilseed meals — Determination of oil content — Part 1: Extraction method with hexane (or light petroleum),Tourteaux de graines oléagineuses — Détermination de la teneur en huile — Partie 1: Méthode par extraction à l'hexane (ou à l'éther de pétrole),1998-08-20,1,['67.200.20'],ISO/TC 34/SC 2,9599,[4982],[36502],"['en','fr']",7,

36502,IS,,ISO 734-1:2006,Oilseed meals — Determination of oil content — Part 1: Extraction method with hexane (or light petroleum),Tourteaux de graines oléagineuses — Détermination de la teneur en huile — Partie 1: Méthode par extraction à l'hexane (ou à l'éther de pétrole),2006-10-13,2,['67.200.20'],ISO/TC 34/SC 2,9599,[26835],[66393],"['en','fr','ru']",7,"<p>ISO 734-1:2006 specifies a method for the determination of the hexane extract (or light-petroleum extract), called 'oil content', of meals (excluding compounded products) obtained by the extraction of oil from oilseeds by pressure or solvents.</p>"

4982,IS,,ISO 734:1979,"Oilseeds residues — Determination of hexane extract (or light-petroleum extract), called 'oil content'","Tourteaux de graines oléagineuses — Détermination de l'extrait à l'hexane (ou à l'éther de pétrole), dit 'teneur en huile'",1979-08-01,1,['67.200.20'],ISO/TC 34/SC 2,9599,,"[26835,4983]","['en','fr']",3,

4983,IS,,ISO 734-2:1998,Oilseed residues — Determination of oil content — Part 2: Rapid extraction method,Tourteaux de graines oléagineuses — Détermination de la teneur en huile — Partie 2: Méthode rapide par extraction,1998-08-20,1,['67.200.20'],ISO/TC 34/SC 2,9599,[4982],[36503],"['en','fr']",8,

36503,IS,,ISO 734-2:2008,Oilseed meals — Determination of oil content — Part 2: Rapid extraction method,Tourteaux de graines oléagineuses — Détermination de la teneur en huile — Partie 2: Méthode rapide par extraction,2008-06-23,2,['67.200.20'],ISO/TC 34/SC 2,9599,[4983],[66394],"['en','fr','ru']",8,"<p>ISO 734-2:2008 specifies an extraction method which may be used to assess the efficiency of a de-oiling process by comparing the oil content of the oilseed with the residual oil content of the corresponding extraction meals, pellets and expeller cakes.</p><p>It is not applicable to disputed cases, for which ISO 734-1 is applicable.</p><p>It is applicable to oilseed meals obtained from oilseed

66393,IS,,ISO 734:2015,Oilseed meals — Determination of oil content — Extraction method with hexane (or light petroleum),Tourteaux de graines oléagineuses — Détermination de la teneur en huile — Méthode par extraction à l'hexane (ou à l'éther de pétrole),2015-11-17,2,['67.200.20'],ISO/TC 34/SC 2,9599,[36502],[84181],"['en','fr']",7,"<p>ISO 734:2015 specifies a method for the determination of the hexane extract (or light-petroleum extract), called 'oil content', of meals (excluding compounded products) obtained by the extraction of oil from oilseeds by pressure or solvents.</p>"

14019,IS,,ISO 7341:1985,Banking — Nostro accounts reconciliation,Opérations bancaires — Procédures de rapprochement de comptes,1985-09-26,1,['03.060'],ISO/TC 68,9599,,[27444],"['en','fr']",11,

33218,IS,Cor,ISO 7341:1985/Cor 1:1999,Banking — Nostro accounts reconciliation — Technical Corrigendum 1,Opérations bancaires — Procédures de rapprochement de comptes — Rectificatif technique 1,1999-12-16,1,['03.060'],ISO/TC 68,9599,,[27444],"['en','fr']",1,

27444,IS,,ISO 7341:2000,Banking — Nostro accounts reconciliation,Opérations bancaires — Procédures de rapprochement de comptes,2000-08-31,2,['03.060'],ISO/TC 68,9599,"[14019,33218]",[41109],['en'],16,

14020,IS,,ISO 7342:1982,Road vehicles — Diagnostic systems — Equipment for ignition systems testing,Véhicules routiers — Système de diagnostic — Équipement pour contrôle des systèmes d'allumage,1982-10-01,1,['43.180'],ISO/TC 22,9599,,[21339],"['en','fr']",6,"<p>Defines devices for measuring parameters of ignition systems of internal combustion engines in road vehicles, and their possible methods of use. Applies to plug-in and built-in sensors for exclusively diagnostic purposes. Some figures illustrate diagrams as well as sensor and gauge of concern.</p>"

14021,IS,,ISO 7343:1983,Cinematography — Two-track photographic sound records on 35 mm motion-picture prints — Positions and width dimensions,Cinématographie — Enregistrement de deux pistes sonores optiques sur copies d'exploitation cinématographiques 35 mm — Positions et dimensions en largeur,1983-11-01,1,['37.060.20'],ISO/TC 36,9599,,[20160],"['en','fr']",2,

14023,IS,,ISO 7345:1985,Thermal insulation — Physical quantities and definitions,Isolation thermique — Grandeurs physiques et définitions,1985-05-23,1,"['01.060','27.200']",ISO/TC 163,9599,,[14024],"['en','fr']",,

14024,IS,,ISO 7345:1987,Thermal insulation — Physical quantities and definitions,Isolation thermique — Grandeurs physiques et définitions,1987-11-19,2,"['01.060','27.220']",ISO/TC 163,9599,[14023],[65000],"['en','fr']",7,"<p>Defines physical quantities used in the field of thermal insulation, i.a. quantity of heat, heat flow rate, density of heat flow rate, thermal conductivity, thermal resistance, thermal transmittance, heat capacity, thermal diffusivity, thermal effusivity etc., and gives the corresponding symbols and units.</p>"

14025,IS,,ISO 7346-1:1984,"Water quality — Determination of the acute lethal toxicity of substances to a freshwater fish (Brachydanio rerio, Hamilton-Buchanan (Teleostei, Cyprinidae)) — Part 1: Static method","Qualité de l'eau — Détermination de la toxicité aiguë létale de substances vis-à-vis d'un poisson d'eau douce (Brachydanio rerio Hamilton-Buchanan (Teleostei, Cyprinidae)) — Partie 1: Méthode statique",1984-11-01,1,['13.060.01'],ISO/TC 147/SC 5,9599,,[14026],"['en','fr']",9,

14027,IS,,ISO 7346-2:1984,"Water quality — Determination of the acute lethal toxicity of substances to a freshwater fish (Brachydanio rerio Hamilton-Buchanan (Teleostei, Cyprinidae)) — Part 2: Semi-static method","Qualité de l'eau — Détermination de la toxicité aiguë létale de substances vis-à-vis d'un poisson d'eau douce (Brachydanio rerio Hamilton-Buchanan (Teleostei, Cyprinidae)) — Partie 2: Méthode semi-statique",1984-11-01,1,['13.060.01'],ISO/TC 147/SC 5,9599,,[14028],"['en','fr']",9,

14029,IS,,ISO 7346-3:1984,"Water quality — Determination of the acute lethal toxicity of substances to a freshwater fish (Brachydanio rerio Hamilton-Buchanan (Teleostei, Cyprinidae)) — Part 3: Flow-through method","Qualité de l'eau — Détermination de la toxicité aiguë létale de substances vis-à-vis d'un poisson d'eau douce (Brachydanio rerio Hamilton-Buchanan (Teleostei, Cyprinidae)) — Partie 3: Méthode avec renouvellement continu",1984-11-01,1,['13.060.01'],ISO/TC 147/SC 5,9599,,[14030],"['en','fr']",10,

14034,IS,,ISO 7350:1984,Text communication — Registration of graphic character subrepertoires,Transmission de texte — Procédure d'enregistrement des sous-répertoires de caractères graphiques,1984-03-01,1,['35.040.10'],ISO/IEC JTC 1,9599,,[14035],"['en','fr']",11,

14038,IS,,ISO 7353:1985,Oil of rosewood — Determination of alpha-terpineol content — Gas chromatographic method on packed columns,Huile essentielle de bois de rose — Détermi- nation de la teneur en alpha-terpinéol — Méthode par chromatographie en phase gazeuse sur colonne remplie,1985-11-14,1,['71.100.60'],ISO/TC 54,9599,,[34823],"['en','fr']",3,<p>A small quantity of the oil is analyzed by gas chromatography under specified conditions on a packed column. The alpha -terpineol content is determined by using the internal standard method. Operating temperatures: Oven: isotherm between 120 and 150 °C. Injection system: about 170 °C. Detector: about 170 °C.</p>

14041,IS,,ISO 7355:1985,Oils of sassafras and nutmeg — Determination of safrole and cis- and trans-isosafrole content — Gas chromatographic method on packed columns,Huiles essentielles de sassafras et de muscade — Détermination de la teneur en safrole et cis- et trans-isosafrole — Méthode par chromatographie en phase gazeuse sur colonne remplie,1985-12-19,1,['71.100.60'],ISO/TC 54,9599,,[14042],"['en','fr']",4,"<p>A small quantity of the oils is analyzed by gas chromatography under specified conditions on a packed column. The safrole and cis- and trans-isosafrole contents are determined by using the internal standard method. As stationary phase are used polydimethylsiloxane, or polyethylene

14043,IS,,ISO 7356:1985,Oils of thujone-containing Artemisia and oil of sage (Salvia officinalis Linnaeus) — Determination of alpha- and beta-thujone content — Gas chromatographic method on packed columns,Huiles essentielles d'artemisia à thujone et de sauge (Salvia officinalis Linnaeus) — Détermination de la teneur en alpha- et bêta-thujone — Méthode par chromatographie en phase gazeuse sur colonne remplie,1985-12-19,1,['71.100.60'],ISO/TC 54,9599,,[14044],"['en','fr']",4,"<p>A small quantity of the oils is analyzed under specified conditions. The alpha- and beta-thujone contents are determined by using the internal standard or addition method. As stationary phase are used cyanopropyl methy

14045,IS,,ISO 7357:1985,Oil of calamus — Determination of cis-beta-asarone content — Gas chromatographic method on packed columns,Huile essentielle de calamus — Détermination de la teneur en cis-beta asarone — Méthode par chromatographie en phase gazeuse sur colonne remplie,1985-12-19,1,['71.100.60'],ISO/TC 54,9599,,[14046],"['en','fr']",3,<p>A small quantity of the oil is analyzed under specified conditions. The cis-beta-asarone contents is determined by using the internal standard or addition method. As stationary phase polyethylene glycol 20000 is used. Operating temperatures: Oven: isotherm about 190 °C. Injection system and detector: about 170 °C.</p>

32043,IS,,ISO 7358:2002,"Oils of bergamot, lemon, citron and lime, fully or partially reduced in bergapten — Determination of bergapten content by high-pressure liquid chromatography (HPLC)","Huiles essentielles de bergamote, de citron, de bigarade et de limette complètement ou partiellement privées de bergaptène — Détermination de la teneur en bergaptène par chromatographie liquide à haute pression (CLHP)",2002-11-05,1,['71.100.60'],ISO/TC 54,9599,,[78850],"['en','fr']",6,"<p>ISO 7358 specifies a high-pressure liquid chromatographic (HPLC) method, using either an internal standard or external standard, for the determination of the bergapten content in oil of bergamot [<i>Citrus aurantium</i

14053,IS,,ISO 7364:1983,Shipbuilding and marine structures — Deck machinery — Accommodation ladder winches,Construction navale et structures maritimes — Auxiliaires de pont — Treuils pour échelles de coupée,1983-05-01,1,['47.020.50'],ISO/TC 8/SC 1,9599,,[61449],"['en','fr']",3,"<p>Specifies requirements and characteristics of lightly powered winches provided with electric, hydraulic or pneumatic drive, and unpowered winches. Does not include requirements for the prime mover used to operate the winch.</p>"

14054,IS,,ISO 7365:1983,Shipbuilding and marine structures — Deck machinery — Towing winches for deep sea use,Construction navale et structures maritimes — Auxiliaires de pont — Treuils de remorque en haute mer,1983-07-01,1,['47.020.50'],ISO/TC 8/SC 4,9599,,[54580],"['en','fr']",5,"<p>Specifies the characteristics of towing winches having electric, hydraulic, diesel or steam drive, which fulfill the functions of hauling, veering, holding and storing towing rope on drum(s). Does not consider fibre rope handling gear but does not exclude its use.</p>"

14056,IS,,ISO 7368:1989,Hydraulic fluid power — Two-port slip-in cartridge valves — Cavities,"Transmissions hydrauliques — Distributeurs à cartouche, à bride, à deux orifices — Logements",1989-07-13,1,['23.100.50'],ISO/TC 131/SC 5,9599,,"[37499,62775]","['en','fr']",17,<p>Specifies the dimensions and other data relating to cavities in which valves are mounted in order to ensure interchangeability. Applies to cavities for valves which are generally applicable to industrial equipment. The corresponding dimensions and sketches are given and illustrated in the figures 1 to 14. The informative annex A contains the bibliography.</p>

62775,IS,,ISO 7368:2016,Hydraulic fluid power — Two-port slip-in cartridge valves — Cavities,"Transmissions hydrauliques — Distributeurs à cartouche, à bride, à deux orifices — Logements",2016-07-28,2,['23.100.50'],ISO/TC 131/SC 5,9599,[14056],[85894],"['en','fr']",36,"<p>ISO 7368:2016 specifies only geometrical data relating to cavities in which two-port hydraulic slip-in cartridge valves are mounted in order to ensure interchangeability.</p><p>NOTE For example, this document does not specify rated pressures.</p><p>It applies to cavities for two-port hydraulic slip-in cartridge valves which are generally applicable to industrial equipment.</p>"

14057,IS,,ISO 7369:1983,Pipework — Flexible metallic hoses — Vocabulary of general terms,Tuyauteries — Tuyaux métalliques flexibles — Vocabulaire des termes généraux,1983-06-01,1,"['23.040.70','01.040.23']",ISO/TC 5/SC 11,9599,,[20552],"['en','fr']",6,

20552,IS,,ISO 7369:1995,Pipework — Flexible metallic hoses — Vocabulary of general terms,Tuyauteries — Tuyaux métalliques flexibles — Vocabulaire des termes généraux,1995-12-21,2,"['23.040.70','01.040.23']",ISO/TC 5/SC 11,9599,[14057],[32408],"['en','fr']",11,"<p>Defines current terms concerning flexible metallic hoses, flexible metallic hose assemblies and accessories. Replaces the first edition, which has been technically revised.</p>"

32408,IS,,ISO 7369:2004,Pipework — Metal hoses and hose assemblies — Vocabulary,Tuyauteries — Tuyaux et tuyauteries métalliques flexibles — Vocabulaire,2004-08-16,3,"['23.040.70','01.040.23']",ISO/TC 5/SC 11,9599,[20552],[76733],"['en','fr']",16,"<p>ISO 7369:2004 defines current terms concerning metal hoses, metal hose assemblies and component parts. It applies to:</p><ul><li> stripwound metal hoses and hose assemblies;</li><li> corrugated metal hoses and hose assemblies.</li></ul>"