Withdrawn and superseded ISO standards — page 156 of 246

13852,IS,,ISO 7216:1992,Acoustics — Agricultural and forestry wheeled tractors and self-propelled machines — Measurement of noise emitted when in motion,Acoustique — Tracteurs agricoles et forestiers à roues et machines automotrices — Mesurage du bruit émis en mouvement,1992-02-19,1,"['17.140.20','65.060.01']",ISO/TC 23/SC 2,9599,,[66228],"['en','fr']",4,<p>Specifies a method for measuring the A-weighted sound pressure level. Does not apply to special forestry machinery as defined in ISO 6814.</p>

13854,IS,,ISO 7218:1985,Microbiology — General guidance for microbiological examinations,Microbiologie — Directives générales pour les examens microbiologiques,1985-09-12,1,['07.100'],ISO/TC 34/SC 9,9599,,[13855],"['en','fr']",14,

13855,IS,,ISO 7218:1996,Microbiology of food and animal feeding stuffs — General rules for microbiological examinations,Microbiologie des aliments — Règles générales pour les examens microbiologiques,1996-02-15,2,['07.100.30'],ISO/TC 34/SC 9,9599,[13854],[36534],"['en','fr']",43,"<p>Gives general instructions for carrying out microbiological examinations in accordance with specific standards. The purpose is to help to ensure the validity of the examinations, to ascertain that the general techniques used for conducting these examinations are the same in all laboratories. May be used wholly or partly for the accreditation of a test laboratory by national organizations.</p>"

29822,IS,Amd,ISO 7218:1996/Amd 1:2001,Microbiology of food and animal feeding stuffs — General rules for microbiological examinations — Amendment 1,Microbiologie des aliments — Règles générales pour les examens microbiologiques — Amendement 1,2001-04-12,2,['07.100.30'],ISO/TC 34/SC 9,9599,,[36534],"['en','fr']",7,

36534,IS,,ISO 7218:2007,Microbiology of food and animal feeding stuffs — General requirements and guidance for microbiological examinations,Microbiologie des aliments — Exigences générales et recommandations,2007-08-02,3,['07.100.30'],ISO/TC 34/SC 9,9599,"[29822,13855]","[79508,64944]","['en','fr','ru']",66,"<p>ISO 7218:2007 gives general requirements and guidance/options intended for three main uses:</p><ul><li>implementation of ISO TC34/SC9 or TC34/SC5 standards for detection or enumeration of microorganisms;</li><li>good laboratory practices for food microbiological laboratories (the purpose is not to detail them in this International Standard, manuals are available for that purpose);</li

52204,IS,Amd,ISO 7218:2007/Amd 1:2013,Microbiology of food and animal feeding stuffs — General requirements and guidance for microbiological examinations — Amendment 1,Microbiologie des aliments — Exigences générales et recommandations — Amendement 1,2013-07-25,3,['07.100.30'],ISO/TC 34/SC 9,9599,,"[79508,64944]","['en','fr','ru']",66,

4953,IS,,ISO 722:1985,Rock drilling — Hollow hexagonal drill-steels in bar form,Forage des roches — Profilé hexagonal creux en acier pour fleurets,1985-10-03,2,['73.100.30'],ISO/TC 82,9599,,[4954],"['en','fr']",,

13861,IS,,ISO 7225:1994,Gas cylinders — Precautionary labels,Bouteilles à gaz — Étiquettes de risque,1994-10-20,1,['23.020.35'],ISO/TC 58/SC 4,9599,,[33253],"['en','fr']",5,"<p>Specifies the design, content, i. e. hazard symbols and text, and application of warning labels for gas cylinders. These labels are intended for use on all gas cylinders containing single gases or gas mixtures.</p>"

13862,IS,,ISO 7226:1985,Dimensions of hexagonal dienuts,Filières hexagonales de filetage à main,1985-05-16,1,['25.100.50'],ISO/TC 29,9599,,[13863],"['en','fr']",,

13864,IS,,ISO 7227:1987,Road vehicles — Lighting and light signalling devices — Vocabulary,Véhicules routiers — Dispositifs d'éclairage et de signalisation lumineuse — Vocabulaire,1987-11-19,1,"['43.040.20','01.040.43']",ISO/TC 22,9599,,[21752],"['en','fr','ru']",11,"<p>Defines terms in the three ISO-languages English, French, and Russian relating to lighting and light signalling devices for road vehicles as defined in ISO 3833 (in certain countries and international bodies, the term 'light' is sometimes used instead of 'lamp'). Alphabetical indexes in English, French, and Russian are also included.</p>"

13865,IS,,ISO 7228:1981,Tracheal tube connectors,Raccords des tubes trachéaux,1981-10-01,1,['11.040.10'],ISO/TC 121,9599,,"[13867,13866]","['en','fr']",3,

13866,IS,,ISO 7228:1985,Tracheal tube connectors,Raccords de tubes trachéaux,1985-06-27,2,['11.040.10'],ISO/TC 121/SC 2,9599,[13865],[13867],"['en','fr']",3,

13867,IS,,ISO 7228:1993,Tracheal tube connectors,Raccords de tubes trachéaux,1993-10-14,3,['11.040.10'],ISO/TC 121/SC 2,9599,"[13865,13866]",[24590],"['en','fr']",4,

13868,IS,,ISO 7229:1997,Rubber- or plastics-coated fabrics — Measurement of gas permeability,Supports textiles revêtus de caoutchouc ou de plastique — Mesure de la perméabilité aux gaz,1997-01-30,1,['59.080.40'],ISO/TC 45/SC 4,9599,,[65594],"['en','fr']",4,"<p>Describes a method of measuring gas transmission through fabrics coated with plastics or rubber. Applicable when the anticipated permeability is less than 3 cubic decimetres, when particular temperature or pressure conditions are required or when the measurement requires the use of particular gases, either in pure state or as a mixture.</p>"

65594,IS,,ISO 7229:2015,Rubber- or plastics-coated fabrics — Measurement of gas permeability,Supports textiles revêtus de caoutchouc ou de plastique — Mesure de la perméabilité aux gaz,2015-08-20,2,['59.080.40'],ISO/TC 45/SC 4,9599,[13868],[82603],"['en','fr']",16,"<p>ISO 7229:2015 specifies two methods for measuring gas transmission through rubber- or plastics-coated fabrics, a property known as permeability.</p>"

4955,IS,,ISO 723:1974,Rock drilling — Forged collared shanks and chuck bushings for hollow hexagonal drill-steels,Forage des roches — Emmanchements à collerette forgée et douilles porte-outils pour profilé hexagonal creux en acier,1974-06-01,1,['73.100.30'],ISO/TC 82,9599,,[4956],"['en','fr']",4,

13870,IS,,ISO 7231:1984,"Polymeric materials, cellular flexible — Method of assessment of air flow value at constant pressure-drop",Matériaux polymères alvéolaires souples — Détermination de l'indice d'écoulement d'air — Méthode à chute de pression constante,1984-12-01,1,['83.100'],ISO/TC 45/SC 4,9599,,[43778],"['en','fr']",4,<p>The air flow value may be used to give an indication of the effects of formulation and production variables on the cellular structure. Describes the method with an apparatus either for negative or for positive pressure. Two figures show the test arrangement.</p>

43778,IS,,ISO 7231:2010,"Polymeric materials, cellular, flexible — Determination of air flow value at constant pressure-drop",Matériaux polymères alvéolaires souples — Détermination de l'indice d'écoulement d'air à chute de pression constante,2010-06-15,2,['83.100'],ISO/TC 45/SC 4,9599,[13870],[82601],"['en','fr','ru']",11,"<p>ISO 7231:2010 specifies two methods for determining the air flow value of flexible cellular polymeric materials.</p><ul><li>method A, for conventional types of flexible cellular polymeric material;</li><li>method B, for all types of flexible cellular polymeric material, but especially for materials with a low permeability to air.</li></ul>"

13871,IS,,ISO 7232:1986,"Rubber or plastics footwear — Antistatic sandals, sabots and clogs","Articles chaussants en caoutchouc ou en plastique — Sandales, sabots et soques antistatiques",1986-06-05,1,['13.340.50'],ISO/TC 94/SC 3,9599,,[20146],"['en','fr']",4,<p>Specifies requirements for products made wholly of rubber or plastics materials. Two tables and a figure give values for the tensile strength and elongation requirements and the construction of the footwear. An annex for the determination of the electrical resistance.</p>

13872,IS,,ISO 7233:1983,Rubber and plastics hoses and hose assemblies — Vacuum resistance — Methods of test,Tuyaux et flexibles en caoutchouc et en plastique — Résistance au vide — Méthodes d'essai,1983-08-01,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[13873],"['en','fr']",1,

13873,IS,,ISO 7233:1991,Rubber and plastics hoses and hose assemblies — Determination of suction resistance,Tuyaux et flexibles en caoutchouc et en plastique — Détermination de la résistance à l'aspiration,1991-11-21,2,['23.040.70'],ISO/TC 45/SC 1,9599,[13872],[38945],"['en','fr']",2,<p>Specifies two test methods as follows: method A - for hoses of nominal bore diameter up to 80 mm; method B - for hoses of nominal bore diameter greater than 80 mm. This second edition cancels and replaces the first edition (1983).</p>

38945,IS,,ISO 7233:2006,Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum,Tuyaux et flexibles en caoutchouc et en plastique — Détermination de la résistance à l'aspiration,2006-02-14,3,['23.040.70'],ISO/TC 45/SC 1,9599,[13873],[68052],"['en','fr']",5,<p>ISO 7233:2006 specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. Applicable dimensions of hoses for each method are as follows:</p><ul><li>method A -- for hoses of nominal bore up to and including 80 mm;</li><li>method B -- for hoses of nominal bore greater than 80 mm;</li><li>method C -- for hoses of all dimensions.</li></ul><p

68052,IS,,ISO 7233:2016,Rubber and plastics hoses and hose assemblies — Determination of resistance to vacuum,Tuyaux et flexibles en caoutchouc et en plastique — Détermination de la résistance à l'aspiration,2016-10-07,4,['23.040.70'],ISO/TC 45/SC 1,9599,[38945],[75645],"['en','fr']",6,<p>ISO 7233:2016 specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. Applicable dimensions of hoses for each method are as follows:</p><p>- method A for hoses of nominal bore up to and including 80 mm;</p><p>- method B for hoses of nominal bore greater than 80 mm;</p><p>- method C for hoses of all dimensions.</p><p>Me

13876,IS,,ISO 7235:1991,"Acoustics — Measurement procedures for ducted silencers — Insertion loss, flow noise and total pressure loss","Acoustique — Méthodes de mesurage pour silencieux en conduit — Perte d'insertion, bruit d'écoulement et perte de pression totale",1991-04-11,1,['91.120.20'],ISO/TC 43/SC 1,9599,,[30385],"['en','fr']",27,<p>Specifies the substitution method for determining the insertion loss. The measurement procedures are intended for laboratory measurements on silencers but may also be used for in situ measurements on silencers if the requirements of ISO 7235 can be met. Applies to silencers for ventilating and air-conditioning systems. Does not apply to reactive silencers

13877,IS,,ISO 7236:1991,Inland navigation vessels — Demountable signal masts for push-tows — Mounting attachment,Bateaux de navigation intérieure — Mâts de signalisation amovibles pour convois poussés — Ferrures d'attache,1991-06-20,1,['47.060'],ISO/TC 8/SC 7,9599,,[65015],"['en','fr']",4,

13880,IS,,ISO 7237:1981,Road vehicles — Masses and dimensions of caravans — Terms and definitions,Véhicules routiers — Masses et dimensions des caravanes — Dénominations et définitions,1981-12-01,1,"['43.100','01.040.43']",ISO/TC 22,9599,,[13881],"['en','fr']",6,

13882,IS,,ISO 7238:1983,Butter — Determination of pH of the serum — Potentiometric method,Beurre — Détermination du pH de la phase aqueuse — Méthode potentiométrique,1983-12-01,1,['67.100.20'],ISO/TC 34/SC 5,9599,,"[40468,13883]","['en','fr']",2,<p>Specifies a method for measuring the potential difference between a glass electrode and a reference electrode in the serum separated from melted butter. Is applicable to all types of butter. The sampling shall be made according to ISO 707. The value measured is expressed as pH unit.</p>

4957,IS,,ISO 724:1978,ISO metric screw threads — Basic dimensions,Filetages métriques ISO — Dimensions de base,1978-11-01,1,['21.040.10'],ISO/TC 1,9599,,[4958],"['en','fr']",5,

4958,IS,,ISO 724:1993,ISO general-purpose metric screw threads — Basic dimensions,Filetages métriques ISO pour usages généraux — Dimensions de base,1993-10-07,2,['21.040.10'],ISO/TC 1,9599,[4957],[85104],"['en','fr']",7,"<p>Specifies the basic dimensions of metric threads in accordance with ISO 261. The basic dimensions are: basic major diameter of internal or external thread (nominal diameter), basic pitch diameter of internal or external thread, basic minor diameter of internal or external thread, height of fundamental triangle, pitch. The values refer to the basic profile in accordance with ISO 68.</p>"

54553,IS,Cor,ISO 724:1993/Cor 1:2009,ISO general-purpose metric screw threads — Basic dimensions — Technical Corrigendum 1,Filetages métriques ISO pour usages généraux — Dimensions de base — Rectificatif technique 1,2009-07-13,2,['21.040.10'],ISO/TC 1,9599,,[85104],"['en','fr']",2,

13885,IS,,ISO 7240-1:1988,Fire detection and alarm systems — Part 1: General and definitions,Systèmes de détection d'incendie et d'alarme — Partie 1: Généralités et définitions,1988-08-25,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[41115],"['en','fr']",5,"<p>Specifies components, requirements for their interconnection and installation and the performance, testing and servicing of parts or of complete systems. Specifies the scope of the entire standard and provides a set of concepts for use in the parts.</p>"

41115,IS,,ISO 7240-1:2005,Fire detection and alarm systems — Part 1: General and definitions,Systèmes de détection et d'alarme d'incendie — Partie 1: Généralités et définitions,2005-12-16,2,['13.220.20'],ISO/TC 21/SC 3,9599,[13885],[55316],['en'],15,"<p>ISO 7240-1:2005 provides a set of general guidelines and definitions to be used in describing the fire detection and alarm system equipment, tests and requirements in the other parts of ISO 7240.</p><p>The components that a fire detection and alarm system can have are shown in Figure 1. Item C of Figure 1 can be replaced by a sound system for emergency purposes, the components of which are shown in Figure 2.</p><p>Fire detectors can be self-c

55316,IS,,ISO 7240-1:2014,Fire detection and alarm systems — Part 1: General and definitions,Systèmes de détection et d'alarme d'incendie — Partie 1: Généralités et définitions,2014-05-21,3,['13.220.20'],ISO/TC 21/SC 3,9599,[41115],[79791],['en'],16,"<p>ISO 7240-1:2014 provides a set of general guidelines and definitions used in describing the fire detection and alarm system (FDAS) equipment installed in and around buildings, and the tests and requirements for these equipments in the other parts of ISO 7240.</p><p>ISO 7240-1:2014 does not apply to smoke alarms, the requirements for which are specified in ISO 12239.</p>"

40729,IS,,ISO 7240-10:2007,Fire detection and alarm systems — Part 10: Point-type flame detectors,Systèmes de détection et d'alarme d'incendie — Partie 10: Détecteurs de flammes ponctuels,2007-01-19,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[57473],['en'],50,"<p>ISO 7240-10:2007 specifies requirements, test methods and performance criteria for point-type, resettable flame detectors that operate using radiation from a flame for use in fire detection systems installed in buildings. Additional requirements for flame detectors for use in marine applications are specified.</p><p>ISO 7240-10:2007 does not cover flame detectors working on different principles from those described in this document (altho

38002,IS,,ISO 7240-11:2005,Fire detection and alarm systems — Part 11: Manual call points,Systèmes de détection et d'alarme d'incendie — Partie 11: Déclencheurs manuels d'alarme,2005-11-03,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[55319],['en'],37,"<p>ISO 7240-11:2005 specifies the requirements, test methods and performance criteria for manual call points in fire detection and fire alarm systems in and around buildings. ISO 7240-11:2005 takes into account indoor and outdoor conditions, the appearance and operation of the manual call points for type A 'direct operation' and type B 'indirect operation' and covers those which are simple mechanical switches, those which are fitted with simple elect

50374,IS,Amd,ISO 7240-11:2005/Amd 1:2009,Fire detection and alarm systems — Part 11: Manual call points — Amendment 1,Systèmes de détection et d'alarme d'incendie — Partie 11: Déclencheurs manuels d'alarme — Amendement 1,2009-04-16,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[55319],['en'],2,

41144,IS,,ISO 7240-12:2006,Fire detection and alarm systems — Part 12: Line type smoke detectors using a transmitted optical beam,Systèmes de détection d'incendie et d'alarme — Partie 12: Détecteurs linéaires de fumée utilisant une transmission par faisceaux lumineux,2006-02-15,1,['13.220.20'],ISO/TC 21/SC 3,9599,,"[62764,50710]",['en'],48,"<p>ISO 7240-12 specifies requirements, test methods and performance criteria for line type smoke detectors for use in fire detection systems installed in buildings. The detectors consist of at least a transmitter and a receiver and can include reflector(s), for the detection of smoke by the attenuation and/or changes in attenuation of an optical beam.</p>

62764,IS,,ISO 7240-12:2014,Fire detection and alarm systems — Part 12: Line type smoke detectors using a transmitted optical beam,Systèmes de détection d'incendie et d'alarme — Partie 12: Détecteurs linéaires de fumée utilisant une transmission par faisceaux lumineux,2014-04-14,2,['13.220.20'],ISO/TC 21/SC 3,9599,[41144],[79448],['en'],50,"<p>ISO 7240-12:2014 specifies requirements, test methods and performance criteria for line-type smoke detectors for use in fire detection systems installed in buildings. The detectors consist of at least a transmitter and a receiver and can include reflector(s), for the detection of smoke by the attenuation and/or changes in attenuation of an optical beam.

38946,IS,,ISO 7240-13:2005,Fire detection and alarm systems — Part 13: Compatibility assessment of system components,Systèmes de détection et d'alarme d'incendie — Partie 13: Estimation de la compatibilité des composants d'un système,2005-04-20,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[75444],['en'],18,"<p>ISO 7240-13:2005 specifies the requirements for compatibility and connectability assessment of system components that either comply with the requirements of ISO 7240 or with a manufacturer's specification where there is no ISO 7240 International Standard. ISO 7240-13:2005 includes only system requirements when these are necessary for compatibility assessment.</p><p>ISO 7240-13:2005 also specif

36865,IS,,ISO 7240-15:2004,"Fire detection and alarm systems — Part 15: Point type fire detectors using scattered light, transmitted light or ionization sensors in combination with a heat sensor",Systèmes de détection et d'alarme d'incendie — Partie 15: Détecteurs d'incendie multicapteurs,2004-02-26,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[63053],['en'],61,"<p>ISO 7240-15:2004 specifies requirements, test methods and performance criteria for point-type resettable multisensor fire detectors for use in fire detection systems installed in buildings, incorporating in one mechanical enclosure at least one smoke sensor and at least one other sensor which responds to heat, and in which the signal(s) o

43017,IS,Cor,ISO 7240-15:2004/Cor 1:2005,"Fire detection and alarm systems — Part 15: Point type fire detectors using scattered light, transmitted light or ionization sensors in combination with a heat sensor — Technical Corrigendum 1",Systèmes de détection et d'alarme d'incendie — Partie 15: Détecteurs d'incendie multicapteurs — Rectificatif technique 1,2005-09-06,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[63053],['en'],2,

51209,IS,,ISO 7240-17:2009,Fire detection and fire alarm systems — Part 17: Short-circuit isolators,Systèmes de détection d'incendie et d'alarme — Partie 17: Isolateurs de court-circuit,2009-07-30,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[69463],['en'],27,"<p>ISO 7240-17:2009 specifies requirements, test methods and performance criteria for short-circuit isolators, for use in fire detection and alarm systems for buildings.</p><p>Means of isolation or protection incorporated within control and indicating equipment in ISO 7240-1:2005, Figure 1, item B, are not covered by ISO 7240-17:2009.</p>"

51210,IS,,ISO 7240-18:2009,Fire detection and alarm systems — Part 18: Input/output devices,Systèmes de détection et d'alarme d'incendie — Partie 18: Dispositifs d'entrée/sortie,2009-10-20,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[69508],['en'],16,"<p>ISO 7240-18:2009 specifies requirements, test methods and performance criteria for input/output devices connected to a transmission path of a fire detection and alarm system used to receive and/or transmit signals to or from the transmission path, necessary for the operation of the fire detection and fire alarm system and/or fire protection system.</p><p>An input/output device can be a physically separate device or its function can be integrated in

36118,IS,,ISO 7240-2:2003,Fire detection and alarm systems — Part 2: Control and indicating equipment,Systèmes de détection et d'alarme d'incendie — Partie 2: Équipement de contrôle et de signalisation,2003-09-10,1,['13.220.20'],ISO/TC 21/SC 3,9599,,"[68437,56103]",['en'],45,"<p>ISO 7240-2:3003 specifies requirements, test methods and performance criteria for control and indicating equipment (c.i.e.) for use in fire detection and fire alarm systems installed in buildings.</p>"

40178,IS,,ISO 7240-22:2007,Fire detection and alarm systems — Part 22: Smoke-detection equipment for ducts,Systèmes de détection et d'alarme d'incendie — Partie 22: Équipement de détection des fumées dans les conduits,2007-05-07,1,['13.220.20'],ISO/TC 21/SC 3,9599,,"[50711,68991]",['en'],41,"<p>ISO 7240-22:2007 specifies requirements, test methods and performance criteria for smoke detection equipment for ducts (s.d.e.d.) for use in fire-detection and fire alarm systems installed in buildings.</p><p>The s.d.e.d. samples the air from a duct and detects smoke in the sample. A common method of operation is to use differential pressure arising from airflow in the duct.</p><p>The s.d.e.d. can use

51211,IS,,ISO 7240-24:2010,Fire detection and fire alarm systems — Part 24: Sound-system loudspeakers,Systèmes de détection d'incendie et d'alarme — Partie 24: Haut-parleurs pour systèmes d'alarme vocale,2010-02-24,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[69879],['en'],39,"<p>ISO 7240-24:2010 specifies requirements, test methods and performance criteria for loudspeakers intended to broadcast a warning of fire between a fire detection and alarm system and the occupants of a building (see item C₄of ISO 7240-1:2005).</p><p>ISO 7240-24:2010 specifies loudspeakers for two types of application environment: type A, generally for indoor use, and type B, generally for outdoor use.</p><p>ISO

57919,IS,Amd,ISO 7240-24:2010/Amd 1:2013,Fire detection and fire alarm systems — Part 24: Sound-system loudspeakers — Amendment 1,Systèmes de détection d'incendie et d'alarme — Partie 24: Haut-parleurs pour systèmes d'alarme vocale — Amendement 1,2013-02-15,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[69879],['en'],1,

44133,IS,,ISO 7240-27:2009,"Fire detection and alarm systems — Part 27: Point-type fire detectors using a scattered-light, transmitted-light or ionization smoke sensor, an electrochemical-cell carbon-monoxide sensor and a heat sensor","Systèmes de détection et d'alarme d'incendie — Partie 27: Détecteurs d'incendie ponctuels utilisant un détecteur de fumée basé sur le principe de la diffusion de la lumière, de la transmission de la lumière ou de l'ionisation, un détecteur de monoxyde de carbone à cellule électrochimique et un détecteur de chaleur",2009-03-23,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[67746],['en'],58,"<p>ISO 7240-27:2009 specifies requirements, test methods and performance criteri

67746,IS,,ISO 7240-27:2018,"Fire detection and alarm systems — Part 27: Point type fire detectors using a smoke sensor in combination with a carbon monoxide sensor and, optionally, one or more heat sensors","Systèmes de détection et d'alarme d'incendie — Partie 27: Détecteurs ponctuels d'incendie utilisant un capteur de fumée en combinaison avec un capteur de monoxyde de carbone (CO) et, optionnellement, un ou plusieurs capteurs de chaleur",2018-05-07,2,['13.220.20'],ISO/TC 21/SC 3,9599,[44133],"[79446,85565]",['en'],61,"<p>This document specifies requirements, test methods and performance criteria for multi-sensor point fire detectors that incorporate a smoke sensor, a carbon monoxide (CO)

44134,IS,,ISO 7240-28:2008,Fire detection and alarm systems — Part 28: Fire protection control equipment,Systèmes de détection et d'alarme d'incendie — Partie 28: Équipement de commande des systèmes de lutte contre l'incendie,2008-10-23,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[61949],['en'],29,"<p>ISO 7240-28:2008 specifies requirements, methods of test and performance criteria for fire protection control equipment (f.p.c.e.) (ISO 7240-1:2005, Figure 1, item G) connected to automatic fire protection equipment (a.f.p.e.) (ISO 7240-1:2005, Figure 1, item H) installed in buildings.</p><p>The f.p.c.e. receives signals from control and indicating equipment (ISO 7240-1:2005, Figure 1, item B), sends

53566,IS,,ISO 7240-3:2010,Fire detection and alarm systems — Part 3: Audible alarm devices,Systèmes de détection et d'alarme d'incendie — Partie 3: Dispositifs d'alarme sonores,2010-12-15,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[72258],['en'],39,"<p>ISO 7240-3:2010 specifies the requirements, test methods and performance criteria for audible alarm devices intended to signal an audible warning of fire between a detection and alarm system and the occupants of a building. It is intended to cover only those devices which derive their operating power by means of a physical electrical connection to an external source such as a fire alarm system.</p><p>ISO 7240-3:2010 is also intended to cover audible

36117,IS,,ISO 7240-4:2003,Fire detection and alarm systems — Part 4: Power supply equipment,Systèmes de détection et d'alarme d'incendie — Partie 4: Équipement d'alimentation électrique,2003-08-11,1,['13.220.20'],ISO/TC 21/SC 3,9599,,"[56104,68438]",['en'],16,"<p>ISO 7240-4:2003 specifies requirements, test methods and performance criteria for power supply equipment (p.s.e.) for use in fire detection and alarm systems installed in buildings. </p>"

36119,IS,,ISO 7240-5:2003,Fire detection and alarm systems — Part 5: Point-type heat detectors,Systèmes de détection et d'alarme incendie — Partie 5: Détecteurs de chaleur ponctuels,2003-12-11,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[55317],['en'],33,"<p>ISO 7240-5:2003 specifies the requirements, test methods and performance criteria for point heat detectors for use in fire detection and fire alarm systems for buildings. For other types of heat detector, or for detectors intended for use in other environments, ISO 7240-5:2003 should be used only for guidance. Heat detectors with special characteristics and developed for specific risks are not covered by this document.</p>"

43018,IS,Cor,ISO 7240-5:2003/Cor 1:2005,Fire detection and alarm systems — Part 5: Point-type heat detectors — Technical Corrigendum 1,Systèmes de détection et d'alarme incendie — Partie 5: Détecteurs de chaleur ponctuels — Rectificatif technique 1,2005-09-06,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[55317],['en'],1,

55317,IS,,ISO 7240-5:2012,Fire detection and alarm systems — Part 5: Point-type heat detectors,Systèmes de détection et d'alarme d'incendie — Partie 5: Détecteurs de chaleur de type ponctuel,2012-06-13,2,['13.220.20'],ISO/TC 21/SC 3,9599,"[43018,36119]",[67759],['en'],34,"<p>ISO 7240-5:2012 specifies requirements, test methods and performance criteria for point-type heat detectors for use in fire detection and fire alarm systems for buildings.</p>"

38771,IS,,ISO 7240-6:2004,Fire detection and alarm systems — Part 6: Carbon monoxide fire detectors using electro-chemical cells,Systèmes de détection et d'alarme incendie — Partie 6: Détecteurs de monoxyde de carbone pour la détection d'incendie utilisant des cellules électro-chimiques,2004-11-03,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[51600],['en'],38,"<p>ISO 7240-6:2004 specifies requirements, test methods and performance criteria for point fire detectors using electro-chemical cells that operate using carbon monoxide detection principles for use in fire detection and fire alarm systems installed in buildings (see ISO 7240-1). CO fire detectors conforming to ISO 7240-6:2004 might not be sui

36120,IS,,ISO 7240-7:2003,"Fire detection and alarm systems — Part 7: Point-type smoke detectors using scattered light, transmitted light or ionization","Systèmes de détection et d'alarme d'incendie — Partie 7: Détecteurs de fumée — Détecteurs ponctuels utilisant le principe de la diffusion de la lumière, de la transmission de la lumière ou de l'ionisation",2003-10-21,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[51166],['en'],48,"<p>ISO 7240-7:2003 specifies requirements, test methods and performance criteria for point-type smoke detectors that operate using scattered light, transmitted light or ionization, for use in fire detection and alarm systems installed in buildings. It is applicable for gui

51166,IS,,ISO 7240-7:2011,"Fire detection and alarm systems — Part 7: Point-type smoke detectors using scattered light, transmitted light or ionization","Systèmes de détection et d'alarme d'incendie — Partie 7: Détecteurs de fumée ponctuels utilisant le principe de la diffusion de la lumière, de la transmission de la lumière ou de l'ionisation",2011-07-28,2,['13.220.20'],ISO/TC 21/SC 3,9599,[36120],[68583],['en'],55,"<p>ISO 7240-7:2011 specifies requirements, test methods and performance criteria for point-type smoke detectors that operate using scattered light, transmitted light or ionization, for use in fire detection and alarm systems installed in buildings (see ISO 7240-1). ISO 7240-7:20

68583,IS,,ISO 7240-7:2018,"Fire detection and alarm systems — Part 7: Point-type smoke detectors using scattered light, transmitted light or ionization","Systèmes de détection et d'alarme d'incendie — Partie 7: Détecteurs de fumée ponctuels utilisant le principe de la diffusion de la lumière, de la transmission de la lumière ou de l'ionisation",2018-05-23,3,['13.220.20'],ISO/TC 21/SC 3,9599,[51166],[79445],['en'],58,"<p>This document specifies requirements, test methods and performance criteria for point-type smoke detectors that operate using scattered light, transmitted light or ionization, for use in fire detection and alarm systems installed in buildings (see ISO 7240-1). This document a

42901,IS,,ISO 7240-8:2007,Fire detection and alarm systems — Part 8: Carbon monoxide fire detectors using an electro-chemical cell in combination with a heat sensor,Systèmes de détection et d'alarme d'incendie — Partie 8: Détecteurs de monoxyde de carbone pour la détection d'incendie utilisant une cellule électrochimique en combinaison avec un capteur de chaleur,2007-08-13,1,['13.220.20'],ISO/TC 21/SC 3,9599,,[60829],['en'],50,"<p>ISO 7240-8:2007 specifies requirements, test methods and performance criteria for point multi-sensor fire detectors that incorporate an electrochemical cell for sensing carbon monoxide (CO) in combination with one or more heat sensors, for use in fire detection and

13891,IS,,ISO 7241-1:1987,Hydraulic fluid power — Quick-action couplings — Part 1: Dimensions and requirements,Transmissions hydrauliques — Raccords rapides — Partie 1: Dimensions et spécifications,1987-04-02,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[54886],"['en','fr']",5,"<p>Lays down the interface dimensions and specifies basic performance requirements for two series of general-purpose quick-action couplings. Both series are in widespread use and have similar technological advantages. The distinction in usage is mainly geographical. Series 'A' (covering sizes 6,3 to 50) is used predominantly in Europe and series 'B' (covering sizes 5 to 50) is predominant in America.</p>"

13892,IS,,ISO 7241-2:1986,Hydraulic fluid power — Quick-action couplings — Part 2: Test methods,Transmissions hydrauliques — Raccords rapides — Partie 2: Méthodes d'essai,1986-12-04,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[29845],"['en','fr']",15,

29845,IS,,ISO 7241-2:2000,Hydraulic fluid power — Quick-action couplings — Part 2: Test methods,Transmissions hydrauliques — Raccords rapides — Partie 2: Méthodes d'essai,2000-03-23,2,['23.100.40'],ISO/TC 131/SC 4,9599,[13892],"[63640,54887]","['en','fr']",22,

54886,IS,,ISO 7241:2014,Hydraulic fluid power — Dimensions and requirements of quick-action couplings,Transmissions hydrauliques — Dimensions et exigences des raccords rapides,2014-07-22,1,['23.100.40'],ISO/TC 131/SC 4,9599,[13891],[82510],"['en','fr']",10,"<p>ISO 7241:2014 specifies the interface dimensions and basic performance requirements for two series of hydraulic quick-action couplings. Both series are in widespread use and have similar technological advantages. Series A is used predominantly in Europe and is preferred worldwide for agricultural and forestry machinery, and ISO 7241:2014 also specifies additional requirements for Series A for use in agricultural machinery applications

13894,IS,,ISO 7243:1982,"Hot environments — Estimation of the heat stress on working man, based on the WBGT-index (wet bulb globe temperature)","Ambiances chaudes — Estimation de la contrainte thermique de l'homme au travail, basée sur l'indice WBGT (température humide et de globe noir)",1982-09-01,1,['13.180'],ISO/TC 159/SC 5,9599,,[13895],"['en','fr']",8,

13895,IS,,ISO 7243:1989,"Hot environments — Estimation of the heat stress on working man, based on the WBGT-index (wet bulb globe temperature)","Ambiances chaudes — Estimation de la contrainte thermique de l'homme au travail, basée sur l'indice WBGT (température humide et de globe noir)",1989-07-20,2,['13.180'],ISO/TC 159/SC 5,9599,[13894],[67188],"['en','fr']",9,"<p>Gives a method, which can easily be used in an industrial environment for evaluating the stresses on a individual. It applies to the evaluation of the mean effect of heat on man during a period representative of his activity but it does not apply to very short periods, nor to zones of comfort.</p>"

4959,IS,,ISO 725:1978,ISO inch screw threads — Basic dimensions,Filetages ISO en inches — Dimensions de base,1978-11-01,1,['21.040.20'],ISO/TC 1,9599,,[51386],"['en','fr']",5,

44152,IS,,ISO 7250-1:2008,Basic human body measurements for technological design — Part 1: Body measurement definitions and landmarks,Définitions des mesures de base du corps humain pour la conception technologique — Partie 1: Définitions des mesures du corps et repères,2008-02-07,1,['13.180'],ISO/TC 159/SC 3,9599,[13903],[65246],"['en','fr']",25,<p>ISO 7250-1:2008 provides a description of anthropometric measurements which can be used as a basis for comparison of population groups. It is intended to serve as a guide for ergonomists who are required to define population groups and apply their knowledge to the geometric design of the places where people work and live.</p>

13903,IS,,ISO 7250:1996,Basic human body measurements for technological design,Définitions des mesures de base du corps humain pour la conception technologique,1996-07-11,1,['13.180'],ISO/TC 159/SC 3,9599,,"[41248,44152]","['en','fr']",21,

13904,IS,,ISO 7251:1984,Microbiology — General guidance for enumeration of presumptive Escherichia coli — Most probable number technique,Microbiologie — Directives générales pour le dénombrement d'Escherichia coli présumés — Technique du nombre le plus probable,1984-11-01,1,['07.100'],ISO/TC 34/SC 9,9599,,[13905],"['en','fr']",9,

13905,IS,,ISO 7251:1993,Microbiology — General guidance for enumeration of presumptive Escherichia coli — Most probable number technique,Microbiologie — Directives générales pour le dénombrement d'Escherichia coli présumés — Technique du nombre le plus probable,1993-12-23,2,['07.100.01'],ISO/TC 34/SC 9,9599,[13904],"[31241,34568]","['en','fr']",7,"<p>Gives general guidelines for the enumeration of presumptive Escherichia coli in products intended for human consumption or feeding of animals, by means of the liquid-medium culture technique and calculation of the most probable number after incubation at 35 °C or 37 °C (this temperature forming the subject of agreement between the parties concer

13907,IS,,ISO 7253:1984,Paints and varnishes — Determination of resistance to neutral salt spray,Peintures et vernis — Détermination de la résistance au brouillard salin neutre,1984-05-01,1,['87.040'],ISO/TC 35/SC 9,9599,,[20357],"['en','fr']",4,

20357,IS,,ISO 7253:1996,Paints and varnishes — Determination of resistance to neutral salt spray (fog),Peintures et vernis — Détermination de la résistance au brouillard salin neutre,1996-12-12,2,['87.040'],ISO/TC 35/SC 9,9599,[13907],"[33276,36935]","['en','fr']",10,<p>Describes a method for determining the resistance of coatings to neutral salt spray in accordance with the requirements of product specifications.</p>

13908,IS,,ISO 7254:1984,Paints and varnishes — Assessment of natural spreading rate — Brush application,Peintures et vernis — Évaluation du rendement d'application normal (naturel) — Application à la brosse,1984-08-01,1,['87.040'],ISO/TC 35/SC 9,9599,,[28228],"['en','fr']",2,

13912,IS,,ISO 7257:1983,Aircraft — Hydraulic tubing joints and fittings — Rotary flexure test,Aéronautique — Joints et raccords pour tubes hydrauliques — Essai de flexion rotative,1983-07-01,1,['49.080'],ISO/TC 20/SC 10,9599,,"[60681,40007]","['en','fr']",9,"<p>Specifies procedures to determine and classify the fatigue strength of reconnectable or permanent hydraulic tube joints. The procedure is intended for conducting flexure tests of these parts with high strength tubes of various alloys such as corrosion resistant steel, Nimonic, titanium and aluminium alloy tube for use on commercial and military aircraft.</p>"

13914,IS,,ISO 7259:1988,Predominantly key-operated cast iron gate valves for underground use,Robinets-vannes en fonte généralement manoeuvrés par clé à béquille pour installations enterrées,1988-12-29,1,"['91.140.60','23.060.30']",ISO/TC 153,9599,,[56006],"['en','fr']",10,<p>Specifies requirements for two types of predominantly key-operated valves for underground use with flanges or spigot ends or socket ends. The two types shall be specified as type A or type B and shall include the following features: inside screw stem; wedge or parallel obturator; metallic or elastomeric obturator seatings; metallic or elastomeric body seatings; ferrous metal and/or copper alloy trims; T-key operation; ri

4960,IS,,ISO 726:1982,Metallic materials — Hardness test — Calibration of standardized blocks to be used for Brinell hardness testing machines,Matériaux métalliques — Essai de dureté — Étalonnage des blocs de référence à utiliser pour les machines d'essai de dureté Brinell,1982-06-01,1,['77.040.10'],ISO/TC 164/SC 3,9599,,[27574],"['en','fr']",3,

13915,IS,,ISO 7261:1987,Photography — 110-size cartridges — Dimensions,Photographie — Chargeurs de format 110 — Dimensions,1987-12-17,1,['37.040.20'],ISO/TC 42,9599,,[22024],"['en','fr']",9,

13916,IS,,ISO 7263:1985,Corrugating medium — Determination of the flat crush resistance after laboratory fluting,Papier cannelure pour carton ondulé — Détermination de la résistance à la compression à plat après cannelage en laboratoire,1985-07-18,1,['85.060'],ISO/TC 6/SC 2,9599,,[1583],"['en','fr']",5,

1583,IS,,ISO 7263:1994,Corrugating medium — Determination of the flat crush resistance after laboratory fluting,Papier cannelure pour carton ondulé — Détermination de la résistance à la compression à plat après cannelage en laboratoire,1994-12-08,2,['85.060'],ISO/TC 6/SC 2,9599,[13916],[41399],"['en','fr']",6,"<p>Cancels and replaces the first edition (1985). Specifies two methods for the determination of the flat crush resistance of corrugating medium after laboratory fluting. The procedures are applicable to any paper intended to be used, after fluting, in the manufacture of corrugated fibreboard.</p>"

41399,IS,,ISO 7263:2008,Corrugating medium — Determination of the flat crush resistance after laboratory fluting,Papier cannelure pour carton ondulé — Détermination de la résistance à la compression à plat après cannelage en laboratoire,2008-12-03,3,['85.060'],ISO/TC 6/SC 2,9599,[1583],[56171],"['en','fr']",8,"<p>ISO 7263:2008 specifies two methods for the determination of the flat crush resistance of corrugating medium after laboratory fluting.</p><p>The procedures are applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board.</p>"

56171,IS,,ISO 7263:2011,Corrugating medium — Determination of the flat crush resistance after laboratory fluting,Papier cannelure pour carton ondulé — Détermination de la résistance à la compression à plat après cannelage en laboratoire,2011-02-09,4,['85.080.30'],ISO/TC 6/SC 2,9599,[41399],"[72431,72432,70916]","['en','fr']",8,"<p>ISO 7263:2011 specifies two methods for the determination of the flat crush resistance of a corrugating medium after laboratory fluting.</p><p>The procedures are applicable to any corrugating medium intended to be used, after fluting, in the manufacture of corrugated board.</p>"

13917,IS,,ISO 7264:1983,Cross-country skis — Dimensions of the binding mounting area for toe clip bindings,Ski de fond — Dimensions de la zone de montage pour les fixations avec étrier,1983-09-01,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[16714],"['en','fr']",3,

13918,IS,,ISO 7265:1984,Cross-country skis — Binding mounting area — Static screw retention strength — Requirements and test method,Skis de fond — Zone de montage de la fixation — Résistance à l'arrachement statique des vis — Spécifications et méthode d'essai,1984-08-01,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[16714],"['en','fr']",4,

13920,IS,,ISO 7267-1:1986,Rubber-covered rollers — Determination of apparent hardness — Part 1: IRHD method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 1: Méthode DIDC,1986-05-22,1,['83.140.99'],ISO/TC 45/SC 2,9599,,[20169],"['en','fr']",2,

20169,IS,,ISO 7267-1:1997,Rubber-covered rollers — Determination of apparent hardness — Part 1: IRHD method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 1: Méthode DIDC,1997-05-29,2,['83.140.99'],ISO/TC 45/SC 2,9599,[13920],[43672],"['en','fr']",3,

43672,IS,,ISO 7267-1:2008,Rubber-covered rollers — Determination of apparent hardness — Part 1: IRHD method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 1: Méthode DIDC,2008-07-21,3,['83.140.99'],ISO/TC 45/SC 2,9599,[20169],[72782],"['en','fr']",4,"<p>ISO 7267-1:2008 specifies a method for the determination of the apparent hardness, expressed in International Rubber Hardness Degrees (IRHD), of vulcanized- or thermoplastic-rubber roller covers. The method is similar in principle to the methods used for the determination of the hardness of rubber in ISO 48 in that it consists essentially of measuring the depth of penetration of a spherical indentor operating

72782,IS,,ISO 7267-1:2017,Rubber-covered rollers — Determination of apparent hardness — Part 1: IRHD method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 1: Méthode DIDC,2017-08-18,4,['83.140.99'],ISO/TC 45/SC 2,9599,[43672],[74971],"['en','fr']",5,"<p>ISO 7267-1:2017 specifies a method for the determination of the apparent hardness, expressed in International Rubber Hardness Degrees (IRHD), of vulcanized- or thermoplastic-rubber roller covers. The method is similar in principle to the methods used for the determination of the hardness of rubber in ISO 48 in that it consists essentially of measuring the depth of penetration of a spherical indentor operating

13921,IS,,ISO 7267-2:1986,Rubber-covered rollers — Determination of apparent hardness — Part 2: Shore-type durometer method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 2: Méthode au duromètre type Shore,1986-07-03,1,['83.140.99'],ISO/TC 45/SC 2,9599,,[43673],"['en','fr']",2,"<p>Describes the measurements of the appropriate hardness where only medium precision is required. The method and apparatus used are essentially those described in ISO 7619, the measurements in this case being made on the curved surface. Shore-type A and D instruments are specified, the latter being used for measurements on rollers of high hardness. Part 1 and 3 of this standard deal w

43673,IS,,ISO 7267-2:2008,Rubber-covered rollers — Determination of apparent hardness — Part 2: Shore-type durometer method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 2: Méthode au duromètre type Shore,2008-07-21,2,['83.140.99'],ISO/TC 45/SC 2,9599,[13921],[74972],"['en','fr']",3,"<p>ISO 7267-2:2008 specifies a method for the determination of the apparent hardness of vulcanized- or thermoplastic-rubber roller covers, expressed in Shore hardness, for measurement where only medium precision is required. The method and apparatus used are essentially those described in ISO 7619‑1, the measurements in this case being made on the curved surface of the condition

13922,IS,,ISO 7267-3:1988,Rubber-covered rollers — Determination of apparent hardness — Part 3: Pusey and Jones method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 3: Méthode Pusey et Jones,1988-03-17,1,['83.140.99'],ISO/TC 45/SC 2,9599,,[42238],"['en','fr']",3,"<p>Describes the method for the determination of the depth of indentation of an indentor under a specified force into the surface of rubber. This depth does not correspond with hardness as measured in accordance with ISO 48, ISO 1400 and ISO 1818. The Pusey and Jones indentation value is an inverse measurements of hardness, i.e. the harder the rubber the lower the Pusey and Jones indentation value.

42238,IS,,ISO 7267-3:2007,Rubber-covered rollers — Determination of apparent hardness — Part 3: Pusey and Jones method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 3: Méthode Pusey et Jones,2007-05-31,2,['83.140.99'],ISO/TC 45/SC 2,9599,[13922],[57735],"['en','fr']",6,"<p>ISO 7267-3:2007 specifies a method for the determination of the apparent hardness of vulcanized rubber roller covers, expressed as the Pusey and Jones indentation value.</p>"

57735,IS,,ISO 7267-3:2011,Rubber-covered rollers — Determination of apparent hardness — Part 3: Pusey and Jones method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 3: Méthode Pusey et Jones,2011-11-04,3,['83.140.99'],ISO/TC 45/SC 2,9599,[42238],[72783],"['en','fr']",8,

72783,IS,,ISO 7267-3:2017,Rubber-covered rollers — Determination of apparent hardness — Part 3: Pusey and Jones method,Cylindres revêtus de caoutchouc — Détermination de la dureté apparente — Partie 3: Méthode Pusey et Jones,2017-08-18,4,['83.140.99'],ISO/TC 45/SC 2,9599,[57735],[74973],"['en','fr']",8,"<p>ISO 7267-3:2017 specifies a method for the determination of the apparent hardness of vulcanized- or thermoplastic-rubber roller covers, expressed as the Pusey and Jones indentation value.</p><p>The Pusey and Jones plastometer apparatus is used to measure the depth of indentation of an indentor under a specified force into the surface of the rubber. The indentation value should not be confu

13926,IS,,ISO 7269:1987,Rubber — Determination of free sulfur,Caoutchouc — Détermination du soufre libre,1987-10-22,1,['83.060'],ISO/TC 45,9599,,[21819],"['en','fr']",9,

4961,IS,,ISO 727:1979,Unplasticized polyvinyl chloride (PVC) fittings with plain sockets for pipes under pressure — Dimensions of sockets — Metric series,Raccords en polychlorure de vinyle (PVC) non plastifié à emboîtements lisses pour tubes sous pression — Dimensions des emboîtements — Série métrique,1979-09-01,3,['23.040.45'],ISO/TC 138,9599,,[4962],"['en','fr']",1,

4962,IS,,ISO 727:1985,"Fittings of unplasticized polyvinyl chloride (PVC-U), chlorinated polyvinyl chloride (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure — Dimensions of sockets — Metric series","Raccords en polychlorure de vinyle non plastifié (PVC-U), en polychlorure de vinyle chloré (PVC-C) ou en acrylonitrile/butadiène/styrène (ABS), à emboîtements lisses pour tubes sous pression — Dimensions des emboîtures — Série métrique",1985-09-05,4,['23.040.45'],ISO/TC 138/SC 2,9599,[4961],"[27405,27406]","['en','fr']",2,"<p>Specifies the dimensions of plain sockets, intended for solvent cementing to pipes of the corresponding material for use under pr

27406,IS,,ISO 727-2:2002,"Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure — Part 2: Inch-based series","Raccords en poly(chlorure de vinyle) non plastifié (PVC-U), en poly(chlorure de vinyle) chloré (PVC-C) ou en acrylonitrile/butadiène/styrène (ABS), à emboîtements lisses pour tubes sous pression — Partie 2: Série basée sur les inches",2002-06-06,1,['23.040.45'],ISO/TC 138/SC 2,9599,[4962],[41887],"['en','fr']",6,"<p>This part of ISO 727 specifies the dimensions, in millimetres, of plain sockets (cylindrical and conical), for the inch-based pipe series

33761,IS,,ISO 7270-1:2003,Rubber — Analysis by pyrolytic gas-chromatographic methods — Part 1: Identification of polymers (single polymers and polymer blends),Caoutchouc — Méthodes d'analyse par pyrolyse et chromatographie en phase gazeuse — Partie 1: Identification des polymères (un seul polymère ou un mélange de polymères),2003-04-14,1,['83.060'],ISO/TC 45/SC 2,9599,[13927],[77433],['en'],54,"<p>ISO 7270-1:2003 specifies a method for the identification of polymers, or blends of polymers, in raw rubbers and in vulcanized or unvulcanized compounds from pyrograms (pyrolysis-gas chromatographic patterns) obtained under the same conditions. This allows qualitative identification of single rubbe

53037,IS,Amd,ISO 7270-1:2003/Amd 1:2010,Rubber — Analysis by pyrolytic gas-chromatographic methods — Part 1: Identification of polymers (single polymers and polymer blends) — Amendment 1,Caoutchouc — Méthodes d'analyse par pyrolyse et chromatographie en phase gazeuse — Partie 1: Identification des polymères (un seul polymère ou un mélange de polymères) — Amendement 1,2010-07-05,1,['83.060'],ISO/TC 45/SC 2,9599,,[77433],['en'],2,