Withdrawn and superseded ISO standards — page 14 of 246

5594,IS,,ISO 1089:1980,Electrode taper fits for spot welding equipment — Dimensions,Emmanchements coniques d'électrodes pour machines à souder par points — Dimensions,1980-03-01,1,['25.160.30'],ISO/TC 44/SC 6,9599,,"[26731,84396,81089]","['en','fr']",3,"<p>Refers to taper dimensions and tolerances for electrode caps, electrode adaptors, electrode holders and similar parts, where the electrode force Fmax, given for diameter d1 in tables 1, 2 and 3 is not exceeded. Establishes dimensions, designation and marking. Cancels and replaces ISO Recommendation R 1089-1969, of which it constitutes a technical revision.</p>"

44675,IS,,ISO 10893-6:2011,Non-destructive testing of steel tubes — Part 6: Radiographic testing of the weld seam of welded steel tubes for the detection of imperfections,Essais non destructifs des tubes en acier — Partie 6: Contrôle radiographique du cordon de soudure des tubes en acier soudés pour la détection des imperfections,2011-03-24,1,"['77.040.20','23.040.10','77.140.75']",ISO/TC 17/SC 19,9599,[21552],"[67444,69805]","['en','fr']",14,<p>ISO 10893-6:2011 specifies requirements for film-based radiographic X-ray testing of the longitudinal or helical weld seams of automated fusion arc-welded steel tubes for the detection of imperfections.</p><p>It can also be applicable to the testing

46367,IS,,ISO 10893-7:2011,Non-destructive testing of steel tubes — Part 7: Digital radiographic testing of the weld seam of welded steel tubes for the detection of imperfections,Essais non destructifs des tubes en acier — Partie 7: Contrôle radiographique numérique du cordon de soudure des tubes en acier soudés pour la détection des imperfections,2011-03-24,1,"['77.040.20','23.040.10','77.140.75']",ISO/TC 17/SC 19,9599,,"[67445,69806]","['en','fr']",17,<p>ISO 10893-7:2011 specifies the requirements for digital radiographic X-ray testing by either computed radiography (CR) or radiography with digital detector arrays (DDA) of the longitudinal or helical weld seams of automatic fusion arc-weld

50580,IS,,ISO 10896-1:2012,Rough-terrain trucks — Safety requirements and verification — Part 1: Variable-reach trucks,Chariots tout-terrain — Exigences de sécurité et vérification — Partie 1: Chariots à portée variable,2012-06-21,1,['53.060'],ISO/TC 110/SC 4,9599,,[75512],['en'],40,

2745,IS,,ISO 10897:1996,"Collets for tool holders with taper ratio 1:10 — Collets, hoders,nuts","Pinces de serrage pour mandrins à conicité 1:10 — Pinces, mandrins à pinces, écrous de serrage",1996-12-26,1,['25.060.20'],ISO/TC 29,9599,,[64172],"['en','fr']",12,"<p>Specifies the dimensions, materials and manufacturing requirements, and designation of collets for tools with parallel shanks and their corresponding holders and nuts. For non-standardized clamping devices these holders can be agreed upon between customer and supplier.</p>"

18899,IS,,ISO 10898:1992,Spot drills,Forets à pointer,1992-01-30,1,['25.100.30'],ISO/TC 29/SC 9,9599,,[65994],"['en','fr']",2,<p>Specifies the dimensions and other technical parameters of spot drills of high-speed steel and hardmetal with point angle of 90° or 120°. Applies to diameters from 4 mm to 20 mm.</p>

5595,IS,,ISO 1090:1981,Office machines and data processing equipment — Function key symbols on typewriters,Machines de bureau et machines employées en traitement de l'information — Symboles des touches de fonction des machines à écrire,1981-01-01,1,['35.260'],ISO/IEC JTC 1,9599,,"[17914,17910,17911,17915,17912,17909,17913]","['en','fr']",3,

2688,IS,,ISO 10907-1:1996,Tools for moulding — Locating rings — Part 1: Locating rings for mounting without thermal insulating sheets in small or medium moulds — Types A and B,Outillage de moulage — Bagues de centrage — Partie 1: Bagues de centrage pour montage sans feuille d'isolation thermique dans les petits et les moyens moules — Types A et B,1996-12-12,1,['25.120.30'],ISO/TC 29/SC 8,9599,,[45060],"['en','fr']",7,"<p>Gives the basic dimensions and tolerances of locating rings for mounting of moulds without thermal insulating sheets. The locating rings are suitable for injection moulding machines up to size E12, in accordance with EUROMAP 2, type A (with bore) and type B (without bore). I

5596,IS,,ISO 1091:1977,Typewriters — Layout of printing and function keys,Machines à écrire — Disposition des touches d'impression et des touches de fonction,1977-08-01,1,['35.260'],ISO/IEC JTC 1,9599,,"[17914,17910,17911,17915,17912,17909,17913]","['en','fr']",2,

2697,IS,,ISO 10911:1994,Solid hardmetal end mills with parallel shank — Dimensions,Fraises cylindriques deux tailles monobloc en métaux-durs — Dimensions,1994-11-10,1,['25.100.20'],ISO/TC 29/SC 9,9599,,[43573],"['en','fr']",2,<p>Specifies the dimensions of solid hardmetal end mills with parallel shank.</p>

43573,IS,,ISO 10911:2010,Solid hardmetal end mills with cylindrical shank — Dimensions,Fraises cylindriques deux tailles monobloc en métaux-durs — Dimensions,2010-02-18,2,['25.100.20'],ISO/TC 29/SC 9,9599,[2697],[69345],"['en','fr']",2,<p>ISO 10911:2010 specifies the dimensions of solid hardmetal end mills with cylindrical shank.</p>

46394,IS,,ISO 10916:2014,Calculation of the impact of daylight utilization on the net and final energy demand for lighting,Calcul de l'effet d'utiliser la lumière du jour à la demande énergétique net et finale pour l'éclairage,2014-06-17,1,['91.160.01'],ISO/TC 274,9599,,[78287],['en'],63,"<p>ISO 10916:2014 defines the calculation methodology for determining the monthly and annual amount of usable daylight penetrating non-residential buildings through vertical facades and rooflights and the impact thereof on the energy demand for electric lighting. It can be used for existing buildings and the design of new and renovated buildings.</p><p>ISO 10916:2014 provides the overall lighting energy bal

5597,IS,,ISO 1092-1:1974,Adding machines and calculating machines — Numeric section of ten-key keyboards,Machines à additionner et machines à calculer — Partie 1: des claviers réduits,1974-05-01,1,"['35.160','35.180','35.260']",ISO/IEC JTC 1,9599,,"[17914,17910,17911,17915,17912,17909,17913]","['en','fr']",1,

18904,IS,,ISO 10920:1997,Gas cylinders — 25E taper thread for connection of valves to gas cylinders — Specification,Bouteilles à gaz — Filetages coniques 25E pour le raccordement des robinets sur les bouteilles à gaz — Spécifications,1997-03-13,1,['23.020.35'],ISO/TC 58/SC 2,9599,,[50448],"['en','fr']",5,

46404,IS,,ISO 10924-1:2009,Road vehicles — Circuit breakers — Part 1: Definitions and general test requirements,Véhicules routiers — Coupe-circuits — Partie 1: Définitions et exigences générales d'essai,2009-11-27,1,['43.040.10'],ISO/TC 22/SC 32,9599,,[64005],['en'],16,<p>ISO 10924-1:2009 defines terms and specifies general test requirements for circuit breakers for use in road vehicles with a nominal voltage of 12 V or 24 V.</p><p>ISO 10924-1:2009 is intended to be used in conjunction with other parts of ISO 10924.</p><p>ISO 10924-1:2009 is not applicable to circuit breaker holders (electrical centres or fuse-holders) used in vehicles.</p>

64005,IS,,ISO 10924-1:2016,Road vehicles — Circuit breakers — Part 1: Definitions and general test requirements,Véhicules routiers — Coupe-circuits — Partie 1: Définitions et exigences d'essais générales,2016-04-04,2,['43.040.10'],ISO/TC 22/SC 32,9599,[46404],[82646],['en'],15,"<p>ISO 10924-1:2016 defines terms and specifies general test requirements for circuit breakers for use in road vehicles with a nominal voltage of 12 V d.c., 24 V d.c, 48 V d.c. and 450 V d.c.</p><p>ISO 10924-1:2016 is intended to be used in conjunction with other parts of ISO 10924. The numbering of its clauses corresponds to that of this part of ISO 10924 whose requirements are applicable, except where modified by re

52436,IS,,ISO 10924-2:2014,Road vehicles — Circuit breakers — Part 2: User's guide,Véhicules routiers — Coupe-circuits — Partie 2: Guide de l'utilisateur,2014-02-18,1,['43.040.10'],ISO/TC 22/SC 32,9599,,[82647],['en'],25,<p>ISO 10924-2:2014 gives guidance for the choice and application of automotive circuit breakers. It describes the various parameters which have to be taken into account when selecting circuit breakers.</p>

58089,IS,,ISO 10924-3:2015,"Road vehicles — Circuit breakers — Part 3: Miniature circuit breakers with tabs (Blade type), Form CB11","Véhicules routier — Coupe circuites — Partie 3: Coupe circuits miniatures avec languette (type languette), Forme CB11",2015-04-02,1,['43.040.10'],ISO/TC 22/SC 32,9599,,[82648],['en'],11,"<p>ISO 10924-3:2015 specifies miniature circuit breakers with tabs (blade-type), Form CB11 for use in road vehicles. It establishes, for this circuit breaker form, the rated current, test procedures, performance requirements and dimensions.</p><p>ISO 10924-3:2015 is intended to be used in conjunction with ISO 10924‑1 and with ISO 10924‑2. The numbering of its clauses correspon

46405,IS,,ISO 10924-4:2009,"Road vehicles — Circuit breakers — Part 4: Medium circuit breakers with tabs (Blade type), Form CB15","Véhicules routiers — Coupe-circuits — Partie 4: Coupe-circuits moyens à languettes (de type lame), forme CB15",2009-11-27,1,['43.040.10'],ISO/TC 22/SC 32,9599,,[64006],['en'],14,"<p>ISO 10924-4:2009 specifies medium circuit breakers with tabs (Blade type), Form CB15, for use in road vehicles. It establishes, for this circuit breaker form, the rated current, test procedures, performance requirements and dimensions.</p><p>ISO 10924-4:2009 is intended to be used in conjunction with ISO 10924-1 and with ISO 10924-2. The numbering of its clauses corresponds to that of

64006,IS,,ISO 10924-4:2015,"Road vehicles — Circuit breakers — Part 4: Medium circuit breakers with tabs (Blade type), Form CB15","Véhicules routiers — Coupe-circuits — Partie 4: Coupe-circuits moyens à languettes (de type lame), forme CB15",2015-07-20,2,['43.040.10'],ISO/TC 22/SC 32,9599,[46405],[82649],['en'],14,"<p>ISO 10924-4:2015 specifies medium circuit breakers with tabs (Blade type), Form CB15, for use in road vehicles. It establishes, for this circuit breaker form, the rated current, test procedures, performance requirements and dimensions.</p><p>ISO 10924-4:2015 is intended to be used in conjunction with ISO 10924‑1 and with ISO 10924‑2. The numbering of its clauses corresponds to

60999,IS,,ISO 10924-5:2016,Road vehicles — Circuit breakers — Part 5: Circuit breakers with bolt with rated voltage of 450 V,Véhicules routiers — Coupe-circuits — Partie 5: Coupe circuit moyen à boulon avec une tension nominale de 450 V,2016-04-04,1,['43.040.10'],ISO/TC 22/SC 32,9599,,[82650],['en'],10,"<p>ISO 10924-5:2016 specifies circuit breakers with rated voltage of 450 V for use in road vehicles. It establishes, for this circuit breaker type, the rated current, test procedures, performance requirements and dimensions.</p><p>ISO 10924-5:2016 is intended to be used in conjunction with ISO 10924‑1 and with ISO 10924‑2. The numbering of its clauses corresponds to that of ISO 10924‑1 whose

46417,IS,,ISO 10927:2011,Plastics — Determination of the molecular mass and molecular mass distribution of polymer species by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS),"Plastiques — Détermination de la masse moléculaire et de la distribution des masses moléculaires des polymères par spectrométrie de masse, à temps de vol, après désorption/ionisation laser assistée par matrice (SM-MALDI-TOF)",2011-04-07,1,['83.080.01'],ISO/TC 61/SC 5,9599,,[72462],"['en','fr']",13,"<p>ISO 10927:2011 specifies a general method for determining the average molecular mass and molecular mass distribution of polymers from 2 000 g.mol^-1 to 20 000 g.mol<sup

1226,IS,,ISO 10928:1997,Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use,Systèmes de canalisation en matières plastiques — Tubes et raccords plastiques thermodurcissables renforcés de verre (PRV) — Méthodes pour une analyse de régression et leurs utilisations,1997-08-14,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,,[38777],"['en','fr']",39,

38777,IS,,ISO 10928:2009,Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use,Systèmes de canalisation en matières plastiques — Tubes et raccords plastiques thermodurcissables renforcés de verre (PRV) — Méthodes pour une analyse de régression et leurs utilisations,2009-09-09,2,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,[1226],[68568],['en'],51,"<p>ISO 10928:2009 specifies procedures suitable for the analysis of data which, when converted into logarithms of the values, have either a normal or a skewed distribution. It is intended for use with the test methods and referring standards for glass-reinforce

63234,IS,Amd,ISO 10928:2009/Amd 1:2013,Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use — Amendment 1,Systèmes de canalisation en matières plastiques — Tubes et raccords plastiques thermodurcissables renforcés de verre (PRV) — Méthodes pour une analyse de régression et leurs utilisations — Amendement 1,2013-06-19,2,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,,[68568],['en'],3,

68568,IS,,ISO 10928:2016,Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use,Systèmes de canalisation en matières plastiques — Tubes et raccords plastiques thermodurcissables renforcés de verre (PRV) — Méthodes pour une analyse de régression et leurs utilisations,2016-12-14,3,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,"[38777,63234]",[84911],['en'],47,"<p>ISO 10928:2016 specifies procedures suitable for the analysis of data which, when converted into logarithms of the values, have either a normal or a skewed distribution. It is intended for use with the test methods and referring standards for glass-

5598,IS,,ISO 1093:1981,Adding machines and calculating machines — Keytop and printed or displayed symbols,Machines à additionner et machines à calculer — Symboles des touches et symboles imprimés ou affichés,1981-01-01,1,['35.160'],ISO/IEC JTC 1,9599,,"[17914,17910,17911,17915,17912,17909,17913]","['en','fr']",3,

1163,IS,,ISO 10931-1:1997,Plastics piping systems for industrial applications — Poly(vinylidene fluoride) (PVDF) — Part 1: General,Systèmes de canalisation en matières plastiques pour les applications industrielles — Poly(fluorure de vinylidène) (PVDF) — Partie 1: Généralités,1997-02-06,1,['23.040.01'],ISO/TC 138/SC 3,9599,,[36773],"['en','fr']",6,"<p>Contains the requirements for poly(vinylidene fluoride) (PVDF) pipes intended for industrial applications, which include the conveyance of water and chemicals in liquid and gaseous forms. Applicable to pipe systems for use at temperatures up to 150 °C. Does apply to PVDF pipes, fittings, valves and ancillary equipment. Specifies the parameters

21516,IS,,ISO 10931-2:1997,Plastics piping systems for industrial applications — Poly(vinylidene fluoride) (PVDF) — Part 2: Pipes,Systèmes de canalisation en matières plastiques pour les applications industrielles — Poly(fluorure de vinylidène) (PVDF) — Partie 2: Tubes,1997-02-06,1,['23.040.20'],ISO/TC 138/SC 3,9599,,[36773],"['en','fr']",6,"<p>Contains the requirements for poly(vinylidene fluoride) (PVDF) pipes intended for industrial applications, which include the conveyance of water and chemicals in liquid and gaseous forms.</p>"

21517,IS,,ISO 10931-3:1996,Plastics piping systems for industrial applications — Poly(vinylidene fluoride) (PVDF) — Part 3: Fittings,Systèmes de canalisation en matières plastiques pour les applications industrielles — Poly(fluorure de vinylidène) (PVDF) — Partie 3: Raccords,1996-08-01,1,['23.040.45'],ISO/TC 138/SC 3,9599,,[36773],"['en','fr']",7,<p>Specifies the characteristics of fittings made from poly(vinylidene fluoride) (PVDF) for industrial applications which include the conveyance of water and chemicals in liquid and gaseous form. Applicable to PVDF fittings intended for the conveyance of fluids under pressure at temperatures up to 150 °Celsius.</p>

1523,IS,,ISO 10931-4:1997,Plastics piping systems for industrial applications — Poly(vinylidene fluoride) (PVDF) — Part 4: Valves,Systèmes de canalisation en matières plastiques pour les applications industrielles — Poly(fluorure de vinylidène) (PVDF) — Partie 4: Robinetterie,1997-11-13,1,"['23.060.01','83.140.30']",ISO/TC 138/SC 7,9599,,[36773],"['en','fr']",7,

21519,IS,,ISO 10931-5:1998,Plastics piping systems for industrial applications — Poly(vinylidene fluoride) (PVDF) — Part 5: Fitness for purpose of the system,Systèmes de canalisation en matières plastiques pour les applications industrielles — Poly(fluorure de vinylidène) (PVDF) — Partie 5: Aptitude à l'emploi du système,1998-06-04,1,['23.040.01'],ISO/TC 138/SC 3,9599,,[36773],"['en','fr']",2,

1361,IS,,ISO 10933:1997,Polyethylene (PE) valves for gas distribution systems,Robinets en polyéthylène (PE) pour distribution de gaz,1997-11-06,1,"['75.200','83.140.30']",ISO/TC 138/SC 7,9599,,[62613],"['en','fr']",27,

35112,IS,,ISO 10934-1:2002,Optics and optical instruments — Vocabulary for microscopy — Part 1: Light microscopy,Optique et instruments d'optique — Vocabulaire relatif à la microscopie — Partie 1: Microscopie optique,2002-12-13,1,"['37.020','01.040.37']",ISO/TC 172/SC 5,9599,,[77327],"['en','fr','ru']",95,<div id='MathJax_Message' style='display: none;'></div><p>This part of ISO 10934 specifies terms and definitions to be used in the field of light microscopy.</p>

39473,IS,,ISO 10934-2:2007,Optics and optical instruments — Vocabulary for microscopy — Part 2: Advanced techniques in light microscopy,Optique et instruments d'optique — Vocabulaire relatif à la microscopie — Partie 2: Techniques avancées en microscopie optique,2007-02-28,1,"['37.020','01.040.37']",ISO/TC 172/SC 5,9599,,"[77327,57547]",['en'],7,<p>ISO 10934-2:2007 specifies terms and definitions to be used in the field of advanced light microscopy.</p>

77327,IS,,ISO 10934:2020,Microscopes — Vocabulary for light microscopy,Microscopes — Vocabulaire relatif à la microscopie optique,2020-08-20,1,"['37.020','01.040.37']",ISO/TC 172/SC 5,9599,"[39473,75096,35112,72608]",[82458],['en'],63,<p>This document specifies terms and definitions to be used in the field of light microscopy and advanced techniques in light microscopy.</p>

18911,IS,,ISO 10935:1996,Optics and optical instruments — Microscopes — Interfacing connection type C,Optique et instruments d'optique — Microscopes — Raccord d'interface de type C,1996-12-26,1,['37.020'],ISO/TC 172/SC 5,9599,,[51305],"['en','fr']",2,<p>Gives the dimensions of a thread mount type C for a microscope imaging exit port and the position of the primary image plane.</p>

18912,IS,,ISO 10936-1:2000,Optics and optical instruments — Operation microscopes — Part 1: Requirements and test methods,Optique et instruments d'optique — Microscopes chirurgicaux — Partie 1: Exigences et méthodes d'essai,2000-06-08,1,"['37.020','11.040.30']",ISO/TC 172/SC 5,9599,,[69819],"['en','fr']",4,

29652,IS,,ISO 10936-2:2001,Optics and optical instruments — Operation microscopes — Part 2: Light hazard from operation microscopes used in ocular surgery,Optique et instruments d'optique — Microscopes chirurgicaux — Partie 2: Danger de la lumière provenant des microscopes opératoires utilisés en chirurgie oculaire,2001-01-18,1,"['37.020','11.040.30']",ISO/TC 172/SC 7,9599,,[44537],"['en','fr']",11,

18913,IS,,ISO 10937:1997,Optics and optical instruments — Microscopes — Diameter of interchangeable eyepieces for microscopes with tube length 160 mm,Optique et instruments d'optique — Microscopes — Diamètre d'optiques interchangeables pour microscopes de longueur de tube 160 mm,1997-09-03,1,['37.020'],ISO/TC 172/SC 5,9599,,[33193],"['en','fr']",1,

33193,IS,,ISO 10937:2000,Optics and optical instruments — Microscopes — Diameter of interchangeable eyepieces,Optique et instruments d'optique — Microscopes — Diamètre d'oculaires interchangeables,2000-12-21,2,['37.020'],ISO/TC 172/SC 5,9599,[18913],[70798],"['en','fr']",1,

18914,IS,,ISO 10938:1998,Ophthalmic instruments — Chart projectors,Instruments ophtalmiques — Projecteurs d'optotypes,1998-05-14,1,['11.040.70'],ISO/TC 172/SC 7,9599,,"[54970,63691]","['en','fr']",3,

18915,IS,,ISO 10939:1998,Ophthalmic instruments — Slit-lamp microscopes,Instruments ophtalmiques — Microscopes avec lampe à fente,1998-07-16,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[39139],"['en','fr']",11,

33789,IS,Cor,ISO 10939:1998/Cor 1:2000,Ophthalmic instruments — Slit-lamp microscopes — Technical Corrigendum 1,Instruments ophtalmiques — Microscopes avec lampe à fente — Rectificatif technique 1,2000-04-20,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[39139],"['en','fr']",1,

39139,IS,,ISO 10939:2007,Ophthalmic instruments — Slit-lamp microscopes,Instruments ophtalmiques — Microscopes avec lampe à fente,2007-01-18,2,['11.040.70'],ISO/TC 172/SC 7,9599,"[33789,18915]",[71865],"['en','fr']",6,"<p>ISO 10939:2007, together with ISO 15004-1 and ISO 15004-2, specifies requirements and test methods for slit-lamp microscopes to provide slit illumination and observation under magnification of the eye and its adnexa.</p><p>ISO 10939:2007 is not applicable to microscope accessories, e.g. photographic equipment and lasers.</p><p>ISO 10939:2007 takes precedence over ISO 15004-1 and ISO 15004-2, if differences exist.</p>"

18916,IS,,ISO 10940:1998,Ophthalmic instruments — Fundus cameras,Instruments ophtalmiques — Appareils photographiques du fond de l'oeil,1998-04-23,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[39140],"['en','fr']",12,

18918,IS,,ISO 10942:1998,Ophthalmic instruments — Direct ophthalmoscopes,Instruments ophtalmiques — Ophtalmoscopes directs,1998-04-23,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[39141],"['en','fr']",13,

30912,IS,Cor,ISO 10942:1998/Cor 1:1998,Ophthalmic instruments — Direct ophthalmoscopes — Technical Corrigendum 1,Instruments ophtalmiques — Ophtalmoscopes directs — Rectificatif technique 1,1998-08-27,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[39141],"['en','fr']",1,

39141,IS,,ISO 10942:2006,Ophthalmic instruments — Direct ophthalmoscopes,Instruments ophtalmiques — Ophtalmoscopes directs,2006-06-09,2,['11.040.70'],ISO/TC 172/SC 7,9599,"[30912,18918]",[82228],"['en','fr']",7,"<p>ISO 10942:2006, together with ISO 15004-1 and ISO 15004-2, specifies minimum requirements and test methods for hand-held direct ophthalmoscopes designed for directly observing the eye fundus.</p><p>ISO 10942:2006 takes precedence over ISO 15004-1 and ISO 15004-2, if differences exist.</p>"

18919,IS,,ISO 10943:1998,Ophthalmic instruments — Indirect ophthalmoscopes,Instruments ophtalmiques — Ophtalmoscopes indirects,1998-04-23,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[39142],"['en','fr']",11,

39142,IS,,ISO 10943:2006,Ophthalmic instruments — Indirect ophthalmoscopes,Instruments ophtalmiques — Ophtalmoscopes indirects,2006-06-09,2,['11.040.70'],ISO/TC 172/SC 7,9599,[18919],[57205],"['en','fr']",4,"<p>ISO 10943:2006, together with ISO 15004-1 and ISO 15004-2 specifies minimum requirements and test methods for hand-held, spectacle-type, and head-worn indirect ophthalmoscopes for observing indirect images of the eye fundus.</p><p>ISO 10943:2006 takes precedence over ISO 15004-1 and ISO 15004-2, if differences exist.</p><p>ISO 10943:2006 is not applicable to condensing lenses used for indirect ophthalmoscopy or to accessories.</p><p>ISO 10943:2006 is not applicable to table-mounted in

57205,IS,,ISO 10943:2011,Ophthalmic instruments — Indirect ophthalmoscopes,Instruments ophtalmiques — Ophtalmoscopes indirects,2011-08-05,3,['11.040.70'],ISO/TC 172/SC 7,9599,[39142],[83736],"['en','fr']",4,"<p>ISO 10943:2011 specifies minimum requirements and test methods for hand-held, spectacle-type, and head-worn indirect ophthalmoscopes for observing indirect images of the eye fundus.</p><p>ISO 10943:2011 is not applicable to condensing lenses used for indirect ophthalmoscopy or to accessories.</p><p>ISO 10943:2011 is not applicable to table-mounted instruments such as Gullstrand ophthalmoscopes and their derivatives, nor to ophthalmoscopes primarily intended for image capture and/or pr

18920,IS,,ISO 10944:1998,Ophthalmic instruments — Synoptophores,Instruments ophtalmiques — Synoptophores,1998-04-30,1,['11.040.70'],ISO/TC 172/SC 7,9599,,[52928],"['en','fr']",6,

18921,IS,,ISO 10945:1994,Hydraulic fluid power — Gas-loaded accumulators — Dimensions of gas ports,Transmissions hydrauliques — Accumulateurs hydropneumatiques — Dimensions des orifices gaz,1994-11-10,1,['23.100.99'],ISO/TC 131,9599,,[56812],"['en','fr']",2,"<p>Specifies the types and the dimensions of the gas filling ports of gas-loaded accumulators used in hydraulic fluid power systems. Describes two male ports for filling the gas side of a gas-loaded accumulator. These ports are designated by the following: male port with M 16 × 2 thread in accordance with ISO 261 and ISO 724, which is preferred for new designs; male port with 8V1 thread in accordance with ISO 4570-1.</p>"

18922,IS,,ISO 10946:1999,Hydraulic fluid power — Gas-loaded accumulators with separator — Selection of preferred hydraulic ports,Transmissions hydrauliques — Accumulateurs hydropneumatiques avec séparateur — Sélection des orifices hydrauliques préférentiels,1999-03-18,1,['23.100.99'],ISO/TC 131,9599,,"[74014,56813]","['en','fr']",4,

5600,IS,,ISO 1095:1976,Shipbuilding — Toughened safety glass panes for ship's side scuttles,Construction navale — Verres de sécurité trempés pour hublots de navires,1976-08-01,2,"['47.020.10','81.040.30']",ISO/TC 8/SC 8,9599,,[5601],"['en','fr']",3,

5601,IS,,ISO 1095:1989,Shipbuilding and marine structures — Toughened safety glass panes for side scuttles,Construction navale et structures maritimes — Verres de sécurité trempés pour hublots de navires,1989-09-21,3,"['47.020.10','81.040.30']",ISO/TC 8/SC 8,9599,[5600],[34364],"['en','fr']",3,"<p>Specifies materials and finish, dimensions for interchangeability, tolerances and flatness, testing, marking and designation complying with ISO 1751.</p>"

26653,IS,,ISO 10952:1999,Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack from the inside of a section in a deflected condition,Systèmes de canalisations en matières plastiques — Tubes et raccords en plastiques thermodurcissables renforcés de verre (PRV) — Détermination de la résistance à une attaque chimique par l'intérieur d'un tronçon de tube soumis à déflexion,1999-08-05,1,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,,[44085],['en'],9,

44085,IS,,ISO 10952:2008,Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition,Systèmes de canalisations en matières plastiques — Tubes et raccords en plastiques thermodurcissables renforcés de verre (PRV) — Détermination de la résistance à une attaque chimique à l'intérieur d'un tronçon de tube soumis à déflexion,2008-10-02,2,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,[26653],[63949],['en'],9,"<p>ISO 10952:2008 specifies a method for determining the chemical resistance properties of glass-reinforced thermosetting plastics (GRP) pipes and fittin

63949,IS,,ISO 10952:2014,Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition,Systèmes de canalisations en matières plastiques — Tubes et raccords en plastiques thermodurcissables renforcés de verre (PRV) — Détermination de la résistance à une attaque chimique à l'intérieur d'un tronçon de tube soumis à déflexion,2014-03-24,3,"['23.040.45','23.040.20']",ISO/TC 138/SC 6,9599,[44085],[79759],['en'],8,"<p>ISO 10952:2014 specifies a method for determining the chemical resistance properties of glass-reinforced thermosetting plastics (GRP) pipes and fittin

18931,IS,,ISO 10957:1993,Information and documentation — International standard music number (ISMN),Information et documentation — Numéro international normalisé de la musique (ISMN),1993-12-02,1,['01.140.20'],ISO/TC 46/SC 9,9599,,[43173],"['en','fr']",4,"<p>Specifies a means of uniquely identifying printed music publications. Standardizes and promotes internationally the use of numbers on printed music publications in order that one edition of a title or one separate component of an edition can be distinguished from all other editions or components by means of a unique international standard music number made up of the following elements: preceded by the letters ISMN, the letter M as a pref

43173,IS,,ISO 10957:2009,Information and documentation — International standard music number (ISMN),Information et documentation — Numéro international normalisé de la musique (ISMN),2009-07-30,2,['01.140.20'],ISO/TC 46/SC 9,9599,[18931],[83122],"['en','fr']",13,"<p>ISO 10957:2009 specifies the International standard music number (ISMN), which is a means of uniquely identifying editions of notated music. It specifies the assignment of a unique ISMN on such editions so as to distinguish one edition of a title or one separate component of an edition from all other editions. ISO 10957:2009 also specifies the construction of an ISMN and its location on editions of notated music. </p><p>ISO 10957

27263,IS,,ISO 10958-2:1999,Snowboards — Binding mounting area — Part 2: Requirements and test methods for snowboards with inserts,Surfs des neiges — Zone de montage de la fixation — Partie 2: Exigences et méthodes d'essai relatives aux surfs des neiges munis d'inserts,1999-11-25,1,['97.220.20'],ISO/TC 83/SC 4,9599,,[37795],"['en','fr']",5,

37795,IS,,ISO 10958-2:2004,Snowboards — Binding mounting area — Part 2: Requirements and test methods for snowboards with inserts,Surfs des neiges — Zone de montage de la fixation — Partie 2: Exigences et méthodes d'essai relatives aux surfs des neiges munis d'inserts,2004-09-01,2,['97.220.20'],ISO/TC 83/SC 4,9599,[27263],[66926],"['en','fr']",5,"<p>ISO 10958-2:2004 specifies requirements and test methods for snowboards on which bindings are attached by means of inserts that are not removable and screws.</p><p>ISO 10958-2:2004 does not apply to snowboards for children with a mass less then 25 kg.</p><p>It contains data for the manufacturer of snowboards, bindings and retention devices concer

18933,IS,,ISO 10959:2000,Aerospace — MJ threads — Gauging,Aéronautique et espace — Filetage MJ — Vérification par calibres,2000-01-27,1,['49.030.10'],ISO/TC 20/SC 4,9599,,[66320],"['en','fr']",19,

5602,IS,,ISO 1096:1975,Plywood — Classification,Contreplaqué — Classification,1975-08-01,1,['79.060.10'],ISO/TC 89,9599,,[5603],"['en','fr']",1,

5603,IS,,ISO 1096:1999,Plywood — Classification,Contreplaqué — Classification,1999-04-15,2,['79.060.10'],ISO/TC 89/SC 3,9599,[5602],[61092],"['en','fr']",3,

61092,IS,,ISO 1096:2014,Plywood — Classification,Contreplaqué — Classification,2014-01-22,3,['79.060.10'],ISO/TC 89/SC 3,9599,[5603],[80859],['en'],2,<p>ISO 1096:2013 provides systems of classification of plywood panels based on general appearance and principal characteristics.</p>

18934,IS,,ISO 10960:1994,Rubber and plastics hoses — Assessment of ozone resistance under dynamic conditions,Tuyaux en caoutchouc et en plastique — Évaluation de la résistance à l'ozone dans des conditions dynamiques,1994-11-24,1,['23.040.70'],ISO/TC 45/SC 1,9599,,[72847],"['en','fr']",3,<p>Specifies a method of assessing the resistance of hoses to the deleterious effects of atmospheric ozone under dynamic conditions. Applicable to hoses with bore diameters up to and including 25 mm.</p>

46443,IS,,ISO 10961:2010,"Gas cylinders — Cylinder bundles — Design, manufacture, testing and inspection","Bouteilles à gaz — Cadres de bouteilles — Conception, fabrication, essais et inspection",2010-01-07,1,['23.020.35'],ISO/TC 58/SC 4,9599,,[56856],['en'],20,"<p>ISO 10961:2010 specifies the requirements for the design, construction, testing and initial inspection of a transportable cylinder bundle. It is applicable to cylinder bundles containing compressed gas, liquefied gas and mixtures thereof. It is also applicable to cylinder bundles for acetylene.</p><p>It does not apply to packages in which cylinders are manifolded together in a support frame which is designed to be fixed permanentl

1636,IS,,ISO 10962:1997,Securities — Classification of Financial Instruments (CFI code),Valeurs mobilières — Classification des instruments financiers (code CFI),1997-01-22,1,['03.060'],ISO/TC 68,9599,,[32835],"['en','fr']",19,

29642,IS,Cor,ISO 10962:1997/Cor 1:1997,Securities — Classification of Financial Instruments (CFI code) — Technical Corrigendum 1,Valeurs mobilières — Classification des instruments financiers (code CFI) — Rectificatif technique 1: (Concerne uniquement la version anglaise),1997-12-04,1,['03.060'],ISO/TC 68,9599,,[32835],['en'],1,

32835,IS,,ISO 10962:2001,Securities and related financial instruments — Classification of Financial Instruments (CFI code),Valeurs mobilières et autres instruments financiers concernés — Classification des instruments financiers (code CFI),2001-05-03,2,['03.060'],ISO/TC 68,9599,"[29642,1636]",[44799],"['en','fr','ru']",25,

44799,IS,,ISO 10962:2015,Securities and related financial instruments — Classification of financial instruments (CFI code),Valeurs mobilières et autres instruments financiers concernés — Classification des instruments financiers (code CFI),2015-07-24,3,['03.060'],ISO/TC 68/SC 8,9599,[32835],[73564],['en'],70,"<p>ISO 10962:2015 defines and describes codes for an internationally valid system to classify financial instruments. The classification system applies to financial instruments negotiated internationally as well as to domestic instruments. The term 'financial instruments' refers not only to classical securities, but also covers the innovative financial products that have emerged in diffe

73564,IS,,ISO 10962:2019,Securities and related financial instruments — Classification of financial instruments (CFI) code,Valeurs mobilières et autres instruments financiers concernés — Classification des instruments financiers (code CFI),2019-10-01,4,['03.060'],ISO/TC 68/SC 8,9599,[44799],[81140],['en'],71,"<p>This document defines and describes codes for an internationally valid system to classify financial instruments. The classification system applies to financial instruments negotiated internationally as well as to domestic instruments. The term 'financial instruments' refers not only to classical securities, but also covers the innovative financial products that have emerged in differ

18937,IS,,ISO 10965:1998,Textile floor coverings — Determination of electrical resistance,Revêtements de sol textiles — Détermination de la résistance électrique,1998-11-05,1,['97.150'],ISO/TC 219,9599,,[46257],"['en','fr']",4,

31673,IS,Cor,ISO 10965:1998/Cor 1:1999,Textile floor coverings — Determination of electrical resistance — Technical Corrigendum 1,Revêtements de sol textiles — Détermination de la résistance électrique — Rectificatif technique 1,1999-10-28,1,['97.150'],ISO/TC 219,9599,,[46257],"['en','fr']",1,

18938,IS,,ISO 10966:1994,Textiles — Fabrics for awnings and camping tents — Specification,Textiles — Tissus pour auvents et tentes de camping — Spécifications,1994-06-23,1,"['59.080.30','97.200.30']",ISO/TC 83,9599,,[35114],"['en','fr']",7,"<p>Specifies the most important material characteristics for woven fabrics for awnings (snow awnings, residential awnings, touring awnings) and camping tents (sleeping tents, touring tents, residential tents). It can also be applied to other types of fabrics. To meet the needs arising from different climatic conditions, differential national habits in tent usage or different durability-expectations of the customer, the material requirements are split into

35114,IS,,ISO 10966:2005,Sports and recreational equipment — Fabrics for awnings and camping tents — Specification,Matériel de sports et d'activités de plein air — Étoffes pour auvents et tentes de camping — Spécifications,2005-06-08,2,"['59.080.30','97.200.30']",ISO/TC 83,9599,[18938],"[42074,52654]","['en','fr']",7,"<p>ISO 10966:2005 specifies the most important material characteristics for woven fabrics for awnings and camping tents. It can also be applied to other types of fabric.</p><p>To meet the needs arising from different climatic conditions, different national habits in tent usage or different durability-expectations of the customer, the material requirements are split into two lev

1908,IS,,ISO 10968:1995,Earth-moving machinery — Operator's controls,Engins de terrassement — Commandes de l'opérateur,1995-09-21,1,['53.100'],ISO/TC 127/SC 2,9599,"[10478,13679]",[31188],"['en','fr']",16,<p>Specifies the requirements for primary controls on earth-moving machinery as they relate to the ride-on operator.</p>

31188,IS,,ISO 10968:2004,Earth-moving machinery — Operator's controls,Engins de terrassement — Commandes de l'opérateur,2004-10-07,2,['53.100'],ISO/TC 127/SC 2,9599,[1908],"[66915,77145]","['en','fr']",12,"<p>ISO 10968:2004 specifies requirements and guidelines for the operator's primary controls on earth-moving machinery (as defined in ISO 6165), in as far as those controls relate to the ride-on operator (for remote operator-controlled machines, see ISO 15817). Its provisions for finger-, hand- and foot-operated controls are not intended to prevent usage of other types of controls, control locations or control movements. Nevertheless, it does recommend that the general requirements and prin

5604,IS,,ISO 1097:1975,Plywood — Measurement of dimensions of panels,Contreplaqué — Mesurage des dimensions des panneaux,1975-08-01,1,['79.060.10'],ISO/TC 89,9599,,[26709],"['en','fr']",2,

18943,IS,,ISO 10972-1:1998,Cranes — Requirements for mechanisms — Part 1: General,Appareils de levage à charge suspendue — Prescriptions pour les mécanismes — Partie 1: Généralités,1998-02-19,1,['53.020.20'],ISO/TC 96/SC 9,9599,,[85884],"['en','fr']",10,

46481,IS,,ISO 10975:2009,Tractors and machinery for agriculture — Auto-guidance systems for operator-controlled tractors and self-propelled machines — Safety requirements,Tracteurs et matériels agricoles — Systèmes d'autoguidage pour tracteurs commandés par opérateur et pour machines automotrices — Exigences de sécurité,2009-10-29,1,['65.060.01'],ISO/TC 23/SC 19,9599,,[82670],"['en','fr']",5,<p>ISO 10975:2009 specifies safety requirements for auto-guidance systems used in agricultural tractors and self-propelled agricultural machines.</p><p>It is applicable to auto-guidance systems which are factory installed as an integral part of the tractor or self-propelled machine as well as systems des

46482,IS,,ISO 10976:2012,Refrigerated light hydrocarbon fluids - Measurement of cargoes on board LNG carriers,Hydrocarbures légers réfrigérés — Mesurage des cargaisons à bord des navires méthaniers,2012-06-26,1,['75.180.30'],ISO/TC 28/SC 5,9599,[21888],[68620],['en'],61,

68620,IS,,ISO 10976:2015,Refrigerated light hydrocarbon fluids — Measurement of cargoes on board LNG carriers,Hydrocarbures légers réfrigérés — Mesurage des cargaisons à bord des navires méthaniers,2015-12-10,2,['75.180.30'],ISO/TC 28/SC 5,9599,[46482],[83687],['en'],62,"<p>ISO 10976:2015 establishes all of the steps needed to properly measure and account for the quantities of cargoes on liquefied natural gas (LNG) carriers. This includes, but is not limited to, the measurement of liquid volume, vapour volume, temperature and pressure, and accounting for the total quantity of the cargo on board. This International Standard describes the use of common measurement systems used on board LNG car

18947,IS,,ISO 10977:1993,Photography — Processed photographic colour films and paper prints — Methods for measuring image stability,Photographie — Films et papiers photographiques couleur traités — Méthodes de mesure de la stabilité de l'image,1993-02-11,1,['37.040.20'],ISO/TC 42,9599,,[44126],"['en','fr']",30,"<p>Describes test equipment, test procedure and analytic methods for predicting the long-term dark storage stability of colour photographic images (based on the Arrhenius method) and measuring the colour stability of such products when subjected to certain illuminants at specified temperatures and humidities. Does not specify limits of acceptability for the stability.</p>"

18949,IS,,ISO 10979:1994,Identification of fuel assemblies for nuclear power reactors,Système d'identification des assemblages combustibles destinés aux réacteurs nucléaires,1994-06-09,1,['27.120.10'],ISO/TC 85/SC 6,9599,,[75124],"['en','fr']",4,"<p>Specifies requirements for the unique identification. Was developed primarily for commercial light-water reactor fuel, but may be used for any reactor fuel contained in discrete fuel assemblies that can be identified with an identification code. Defines the characters and proposed sequence to be used in assigning identification to the fuel assemblies. The identification is intended to be borne by the fuel assembly throughout its lifetime. Aims at

5605,IS,,ISO 1098:1975,Veneer plywood for general use — General requirements,Contreplaqué à plis d'usage général — Conditions générales,1975-08-01,1,['79.060.10'],ISO/TC 89,9599,,[5606],"['en','fr']",1,"<p>Deals with sheet material as defined in ISO 2074. Applies to plane panels consisting of at least three plies. Does not apply to panels covered with decorative veneers, coated panels or panels for special use. Specifies the structure of panels, humidity, presentation, characteristics of external and internal plies, and glueing.</p>"

18950,IS,,ISO 10981:1993,Determination of uranium in reprocessing plants dissolver solution — Liquid chromatography method,Dosage de l'uranium dans les solutions de dissolution des usines de retraitement — Méthode par chromatographie en phase liquide,1993-06-10,1,['27.120.30'],ISO/TC 85/SC 5,9599,,[34542],"['en','fr']",6,"<p>The principle of the method specified is diluting the sample in aqueous ascorbic acid solution until the amount of free acid of the nitric solution injected into the chromatograph is lower than 0,1 mol/l in HNO₃, performing ion-pair partition chromatography, detecting the elution of uranium by UV spectrophotometry at a wavelength of 254 nm, measuring the peak

18952,IS,,ISO 10983:1999,Timber structures — Solid timber finger-jointing — Production requirements,Structures en bois — Aboutages à entures multiples de bois massif — Exigences de fabrication,1999-09-02,1,['91.080.20'],ISO/TC 165,9599,,[57425],['en'],14,

18954,IS,,ISO 10985:1992,Caps made of aluminium-plastics combinations for infusion bottles and injection vials — Requirements and test methods,Capsules en combinaison aluminium-plastique pour flacons de perfusion et injection — Spécifications et méthodes d'essai,1992-09-24,1,['11.040.20'],ISO/TC 76,9599,,[30262],"['en','fr']",3,

30262,IS,,ISO 10985:1999,Caps made of aluminium-plastics combinations for infusion bottles and injection vials — Requirements and test methods,Capsules en combinaison aluminium-plastique pour flacons de perfusion et d'injection — Spécifications et méthodes d'essai,1999-09-30,2,['11.040.20'],ISO/TC 76,9599,[18954],[52179],"['en','fr']",4,

52179,IS,,ISO 10985:2009,Caps made of aluminium-plastics combinations for infusion bottles and injection vials — Requirements and test methods,Capsules en combinaison aluminium-plastique pour flacons de perfusion et d'injection — Spécifications et méthodes d'essai,2009-02-03,3,['11.040.20'],ISO/TC 76,9599,[30262],[82226],['en'],4,<p>ISO 10985:2009 specifies general requirements and test methods for caps made of aluminium-plastics combinations in accordance with ISO 8536-7 or ISO 8362-6 intended for use respectively on infusion bottles as specified in ISO 8536-1 and/or injection bottles as specified in ISO 8362-1 and ISO 8362-4.</p><p>The purpose of ISO 10985:2009 is to specify caps that prov

46488,IS,,ISO 10988:2011,Equipment for crop protection — Knapsack motorized air-assisted sprayers — Test methods and performance limits,Matériel de protection des cultures — Pulvérisateurs à dos motorisés à jet porté — Méthodes d'essai et limites de performance,2011-07-15,1,['65.060.40'],ISO/TC 23/SC 6,9599,,[67563],"['en','fr']",19,"<p>ISO 10988:2011 specifies the requirements, test methods and minimum performance limits for knapsack motorized air-blast (twin-fluid) sprayers and air-assisted centrifugal sprayers as defined in ISO 5681. </p><p>It is applicable to those integrally powered knapsack sprayers, equipped with an engine and carried by the operator, intended primarily for use in agr

5607,IS,,ISO 1099:1975,Metals — Axial load fatigue testing,Métaux — Essais de fatigue par charge axiale,1975-11-01,1,['77.040.10'],ISO/TC 164,9599,,"[5608,36108]","['en','fr']",5,"<p>The tests are made to determine fatigue properties. Theys are carried out at room temperature, in air, the loading applied to the test piece being along the longitudinal axis passing through the centroid of each croll-section. ISO 1099 describes form, preparation and testing of test pieces. Does not cover component testing and testing on very thin test pieces.</p>"

36108,IS,,ISO 1099:2006,Metallic materials — Fatigue testing — Axial force-controlled method,Matériaux métalliques — Essais de fatigue — Méthode par force axiale contrôlée,2006-04-07,2,['77.040.10'],ISO/TC 164,9599,[5607],[67847],['en'],21,"<p>ISO 1099:2006 specifies the conditions for carrying out axial, constant-amplitude, force-controlled fatigue tests at ambient temperature on metallic specimens, without deliberately introduced stress concentrations. The object of testing is to provide fatigue information, such as the relation between applied stress and number of cycles to failure for given materials at various stress ratios.</p><p>While the form, preparation and testing of specimens of

46546,IS,,ISO 10991:2009,Micro process engineering — Vocabulary,Génie des microprocédés — Vocabulaire,2009-11-10,1,"['01.040.71','71.040.10']",ISO/TC 48,9599,,[82146],"['en','fr']",7,"<p>ISO 10991:2009 gives terms and definitions for micro process engineering applied in chemistry, pharmacy, biotechnology and food technology.</p>"

18960,IS,,ISO 10993-1:1992,Biological evaluation of medical devices — Part 1: Guidance on selection of tests,Évaluation biologique des dispositifs médicaux — Partie 1: Lignes directrices pour le choix des essais,1992-04-23,1,['11.100'],ISO/TC 194,9599,,[25333],"['en','fr']",11,

21225,IS,Cor,ISO 10993-1:1992/Cor 1:1992,Biological evaluation of medical devices — Part 1: Guidance on selection of tests — Technical Corrigendum 1,Évaluation biologique des dispositifs médicaux — Partie 1: Lignes directrices pour le choix des essais — Rectificatif technique 1,1992-09-09,1,['11.100'],ISO/TC 194,9599,,[25333],"['en','fr']",1,