Withdrawn and superseded ISO standards — page 119 of 246

10252,IS,,ISO 4375:1979,Measurement of liquid flow in open channels — Cableway system for stream gauging,Mesure de débit des liquides dans les canaux découverts — Systèmes de suspension par câbles aériens pour le jaugeage en rivière,1979-04-01,1,['17.120.20'],ISO/TC 113/SC 5,9599,,[30517],"['en','fr']",8,

30517,IS,,ISO 4375:2000,Hydrometric determinations — Cableway systems for stream gauging,Déterminations hydrométriques — Systèmes de suspension par câbles aériens pour le jaugeage en rivière,2000-10-26,2,['17.120.20'],ISO/TC 113/SC 5,9599,[10252],[53978],['en'],26,

10253,IS,,ISO 4377:1982,Liquid flow measurement in open channels — Flat-V weirs,Mesure de débit des liquides dans les canaux découverts — Déversoirs plats en V,1982-11-01,1,['17.120.20'],ISO/TC 113/SC 2,9599,,[10254],"['en','fr']",23,

10254,IS,,ISO 4377:1990,Liquid flow measurement in open channels — Flat-V weirs,Mesure de débit des liquides dans les canaux découverts — Déversoirs en V ouvert,1990-02-22,2,['17.120.20'],ISO/TC 113/SC 2,9599,[10253],[33496],"['en','fr']",18,"<p>Deals with the measurement of flow in rivers and artificial channels using flat-V weirs under steady or slowly varying flow conditions. The standard flat-V weir is a control structure, the crest of which takes the form of a shallow 'V' when viewed in the direction of flow.</p>"

33496,IS,,ISO 4377:2002,Hydrometric determinations — Flow measurement in open channels using structures — Flat-V weirs,Déterminations hydrométriques — Mesure de débit dans les canaux découverts au moyen de structures — Déversoirs en V ouvert,2002-10-17,3,['17.120.20'],ISO/TC 113/SC 2,9599,[10254],[51546],['en'],35,<p>ISO 4377:2002 describes the methods of measurement of flow in rivers and artificial channels under steady or slowly varying conditions using flat-V weirs.</p><p>It also gives guidance on acceptable velocity distribution.</p>

10255,IS,,ISO 4378-1:1983,"Plain bearings — Terms, definitions and classification — Part 1: Design, bearing materials and their properties","Paliers lisses — Termes, définitions et classification — Partie 1: Conception, matériaux pour paliers et leurs propriétés",1983-08-01,1,"['21.100.10','01.040.21']",ISO/TC 123,9599,,[10256],"['en','fr','ru']",16,

10256,IS,,ISO 4378-1:1997,"Plain bearings — Terms, definitions and classification — Part 1: Design, bearing materials and their properties","Paliers lisses — Termes, définitions et classification — Partie 1: Conception, matériaux pour paliers et leurs propriétés",1997-12-25,2,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,[10255],[44204],"['en','fr','ru']",53,

44204,IS,,ISO 4378-1:2009,"Plain bearings — Terms, definitions, classification and symbols — Part 1: Design, bearing materials and their properties","Paliers lisses — Termes, définitions, classification et symboles — Partie 1: Conception, matériaux pour paliers et leurs propriétés",2009-09-02,3,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,[10256],[70491],"['en','fr']",42,"<p>ISO 4378-1:2009 gives the most commonly used terms relating to design, bearing materials and their properties of plain bearings with their definitions and classification. For some terms and word-combinations, the short forms are given, which can be used where they are unambiguous. Self-explanatory terms are given wit

70491,IS,,ISO 4378-1:2017,"Plain bearings — Terms, definitions, classification and symbols — Part 1: Design, bearing materials and their properties","Paliers lisses — Termes, définitions, classification et symboles — Partie 1: Conception, matériaux pour paliers et leurs propriétés",2017-06-20,4,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,[44204],[86318],"['en','fr']",39,"<p>ISO 4378-1:2017 specifies the most commonly used terms relating to design, bearing materials and their properties of plain bearings with their definitions and classification.</p><p>For some terms and word combinations, their short forms are given, which can be used where they are unambiguous. Self-explanatory terms a

10258,IS,,ISO 4378-2:1983,"Plain bearings — Terms, definitions and classification — Part 2: Friction and wear","Paliers lisses — Termes, définitions et classification — Partie 2: Frottement et usure",1983-08-01,1,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,,[44205],"['en','fr','ru']",15,<p>Gives the most commonly used terms applied to friction and wear of plain bearings with their definitions and classification. For some terms and word-combinations their short forms are given which are recommended for use when they are unambiguous; self-explanatory terms are given without definitions.</p>

44205,IS,,ISO 4378-2:2009,"Plain bearings — Terms, definitions, classification and symbols — Part 2: Friction and wear","Paliers lisses — Termes, définitions, classification et symboles — Partie 2: Frottement et usure",2009-09-02,2,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,[10258],[70490],"['en','fr']",18,"<p>ISO 4378-2:2009 gives the most commonly used terms relating to friction and wear of plain bearings with their definitions and classification. For some terms and word-combinations, their short forms are given, which can be used where they are unambiguous. Self-explanatory terms are given without definitions.</p><p>In addition to terms used in English and French, two of the three o

70490,IS,,ISO 4378-2:2017,"Plain bearings — Terms, definitions, classification and symbols — Part 2: Friction and wear","Paliers lisses — Termes, définitions, classification et symboles — Partie 2: Frottement et usure",2017-06-20,3,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,[44205],[86319],"['en','fr']",10,"<p>ISO 4378-2:2017 specifies the most commonly used terms relating to friction and wear of plain bearings with their definitions and classification.</p><p>For some terms and word combinations, their short forms are given, which can be used where they are unambiguous. Self-explanatory terms are given without definitions.</p>"

10260,IS,,ISO 4378-3:1983,"Plain bearings — Terms, definitions and classification — Part 3: Lubrication","Paliers lisses — Termes, définitions et classification — Partie 3: Lubrification",1983-08-01,1,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,,"[10261,44206]","['en','fr','ru']",19,<p>Gives the most commonly used terms applied in the field of plain bearings lubrication as well as their definitions and classification. For some terms and word-combinations their short forms are given which are recommended for use when they are unambiguous; self-explanatory terms are given without definitions.</p>

44206,IS,,ISO 4378-3:2009,"Plain bearings — Terms, definitions, classification and symbols — Part 3: Lubrication","Paliers lisses — Termes, définitions, classification et symboles — Partie 3: Lubrification",2009-09-02,2,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,[10260],[70489],"['en','fr']",28,"<p>ISO 4378-3:2009 gives the most commonly used terms relating to lubrication of plain bearings with their definitions and classification. For some terms and word-combinations, their short forms are given, which can be used when they are unambiguous. Self-explanatory terms are given without definitions.</p><p>In addition to terms used in English and French, two of the three official ISO languag

70489,IS,,ISO 4378-3:2017,"Plain bearings — Terms, definitions, classification and symbols — Part 3: Lubrication","Paliers lisses — Termes, définitions, classification et symboles — Partie 3: Lubrification",2017-06-20,3,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,[44206],[86320],"['en','fr']",20,"<p>ISO 4378-3:2017 specifies the most commonly used terms relating to lubrication of plain bearings with their definitions and classification.</p><p>For some terms and word combinations, their short forms are given, which can be used where they are unambiguous. Self-explanatory terms are given without definitions.</p>"

10263,IS,,ISO 4378-4:1997,"Plain bearings — Terms, definitions and classification — Part 4: Calculation parameters and their symbol","Paliers lisses — Termes, définitions et classification — Partie 4: Paramètres de calcul et leur symbole",1997-12-25,1,"['21.100.10','01.040.21']",ISO/TC 123/SC 6,9599,,"[44207,44208]","['en','fr','ru']",21,

10264,IS,,ISO 4379:1978,Plain bearings — Solid copper alloy bushes _ Dimensions and tolerances,Paliers lisses — Bagues massives en alliages de cuivre — Dimensions et tolérances,1978-11-01,1,['21.100.10'],ISO/TC 123,9599,,[10265],"['en','fr']",5,

10265,IS,,ISO 4379:1993,Plain bearings — Copper alloy bushes,Paliers lisses — Bagues en alliages de cuivre,1993-04-01,2,['21.100.10'],ISO/TC 123/SC 3,9599,[10264],[75584],"['en','fr']",5,<p>Specifies dimensions and tolerances for cylindrical and flanged bushes with internal diameter in the range 6 mm to 200 mm. Applies to solid mono-metal copper alloy bushes to be used as plain bearings with and without oil holes and oil grooves.</p>

75584,IS,,ISO 4379:2018,Plain bearings — Copper alloy bushes,Paliers lisses — Bagues en alliages de cuivre,2018-10-12,3,['21.100.10'],ISO/TC 123/SC 3,9599,[10265],[86138],['en'],7,"<p>This document specifies dimensions and tolerances for cylindrical and flanged bushes with internal diameter, <i>d</i>1, in the range 6 mm to 200 mm.</p><p>It applies to solid mono‑metal copper alloy bushes to be used as plain bearings with and without oil holes and oil grooves.</p>"

4451,IS,,ISO 438:1980,Paper — Determination of bulking thickness and apparent density,Papier — Détermination de l'épaisseur moyenne et de la masse volumique,1980-10-01,1,['85.060'],ISO/TC 6/SC 2,9599,,[4606],"['en','fr']",4,

10267,IS,,ISO 4381:1981,Plain bearings — Lead and tin casting alloys for multilayer plain bearings,Paliers lisses — Alliages moulés de plomb et d'étain pour paliers lisses multicouches,1981-12-01,1,"['77.120.60','21.100.10']",ISO/TC 123,9599,,[10268],"['en','fr']",4,

10268,IS,,ISO 4381:1991,Plain bearings — Lead and tin casting alloys for multilayer plain bearings,Paliers lisses — Alliages moulés de plomb et d'étain pour paliers lisses multicouches,1991-11-21,2,"['77.120.60','21.100.10']",ISO/TC 123/SC 2,9599,[10267],[29499],"['en','fr']",5,

29499,IS,,ISO 4381:2000,Plain bearings — Lead and tin casting alloys for multilayer plain bearings,Paliers lisses — Alliages moulés à base de plomb et à base d'étain pour paliers lisses multicouches,2000-05-04,3,"['77.120.60','21.100.10']",ISO/TC 123/SC 2,9599,[10268],"[57025,45755]","['en','fr']",6,

10269,IS,,ISO 4382-1:1982,Plain bearings — Copper alloys — Part 1: Cast copper alloys for solid and multilayer plain bearings,Paliers lisses — Alliages de cuivre — Partie 1: Alliages de cuivre moulés pour paliers lisses massifs et multicouches,1982-01-01,1,"['77.120.30','21.100.10']",ISO/TC 123,9599,,[10270],"['en','fr']",5,

10270,IS,,ISO 4382-1:1991,Plain bearings — Copper alloys — Part 1: Cast copper alloys for solid and multilayer thick-walled plain bearings,"Paliers lisses — Alliages de cuivre — Partie 1: Alliages de cuivre moulés pour paliers lisses à paroi épaisse, massifs et multicouches",1991-10-24,2,"['77.120.30','21.100.10']",ISO/TC 123/SC 2,9599,[10269],[80044],"['en','fr']",8,<p>Specifies material properties and test methods. Gives a limited selection of alloys currently available for general purposes. This second edition cancels and replaces the first edition (1982). Annexes A and B are for information only.</p>

10271,IS,,ISO 4382-2:1981,Plain bearings — Copper alloys — Part 2: Wrought copper alloys for solid plain bearings,Paliers lisses — Alliages de cuivre — Partie 2: Alliages de cuivre corroyés pour paliers lisses massifs,1981-12-01,1,"['77.120.30','21.100.10']",ISO/TC 123,9599,,[10272],"['en','fr']",3,

10272,IS,,ISO 4382-2:1991,Plain bearings — Copper alloys — Part 2: Wrought copper alloys for solid plain bearings,Paliers lisses — Alliages de cuivre — Partie 2: Alliages de cuivre corroyés pour paliers lisses massifs,1991-10-24,2,"['77.120.30','21.100.10']",ISO/TC 123/SC 2,9599,[10271],[80045],"['en','fr']",4,<p>Specifies material properties and the designation. Gives a limited selection of alloys currently available for general purposes. This second edition cancels and replaces the first edition (1982). Annexes A and B are for information only.</p>

10273,IS,,ISO 4383:1981,Plain bearings — Metallic multilayer materials for thin-walled plain bearings,Paliers lisses — Matériaux métalliques multicouches pour paliers lisses minces,1981-12-01,1,['21.100.10'],ISO/TC 123,9599,,[10274],"['en','fr']",5,

10274,IS,,ISO 4383:1991,Plain bearings — Multilayer materials for thin-walled plain bearings,Paliers lisses — Matériaux multicouches pour paliers lisses minces,1991-10-31,2,['21.100.10'],ISO/TC 123/SC 2,9599,[10273],[29500],"['en','fr']",9,

29500,IS,,ISO 4383:2000,Plain bearings — Multilayer materials for thin-walled plain bearings,Paliers lisses — Matériaux multicouches pour paliers lisses minces,2000-05-04,3,['21.100.10'],ISO/TC 123/SC 2,9599,[10274],"[57026,45758]","['en','fr']",7,

10275,IS,,ISO 4384-1:1982,Plain bearings — Hardness testing of bearing metals — Part 1: Compound materials,Paliers lisses — Essai de dureté des matériaux antifriction — Partie 1: Matériaux multicouches,1982-01-01,1,['21.100.10'],ISO/TC 123,9599,,[29501],"['en','fr']",2,

29501,IS,,ISO 4384-1:2000,Plain bearings — Hardness testing of bearing metals — Part 1: Compound materials,Paliers lisses — Essai de dureté des matériaux antifriction — Partie 1: Matériaux multicouches,2000-05-04,2,['21.100.10'],ISO/TC 123/SC 2,9599,[10275],"[45760,57027]","['en','fr']",3,

57027,IS,,ISO 4384-1:2012,Plain bearings — Hardness testing of bearing metals — Part 1: Multilayer bearings materials,Paliers lisses — Essai de dureté des matériaux antifriction — Partie 1: Matériaux multicouches pour paliers lisses,2012-10-01,3,['21.100.10'],ISO/TC 123/SC 2,9599,[29501],[77094],['en'],2,"<p>ISO 4384-1:2012 specifies parameters for the hardness testing of compound materials for plain bearings made from steel and bearing metal with bearing metals based on copper and aluminium, manufactured by casting, sintering or bonding. It represents a supplement to the existing ISO publications on hardness testing and, therefore, includes only the extensions and restrictions to be observe

10276,IS,,ISO 4384-2:1982,Plain bearings — Hardness testing of bearing metals — Part 2: Solid materials,Paliers lisses — Essai de dureté des matériaux antifriction — Partie 2: Matériaux massifs,1982-01-01,1,['21.100.10'],ISO/TC 123/SC 2,9599,,[57808],"['en','fr']",1,<p>Applies to plain bearings made from cast and wrought copper and aluminium alloys by machining and forming of their wrought products and ingots and of lead and tin ingots. Includes only the extensions and restrictions to be observed as compared to existing ISO publications on hardness testing. In the case of heterogeneous structures the Brinell test is used.</p>

57808,IS,,ISO 4384-2:2011,Plain bearings — Hardness testing of bearing metals — Part 2: Solid materials,Paliers lisses — Essai de dureté des matériaux antifriction — Partie 2: Matériaux massifs,2011-04-27,2,['21.100.10'],ISO/TC 123/SC 2,9599,[10276],[80961],['en'],3,"<p>ISO 4384-2:2011 specifies parameters for the hardness testing of solid materials for plain bearings made from cast and wrought copper and aluminium alloys by machining and forming their wrought products and ingots, and of tin-based ingots. It represents a supplement to existing International Standards on hardness testing and, therefore, includes only the extensions and restrictions for observation compared to those publicatio

10277,IS,,ISO 4385:1981,Plain bearings — Compression testing of metallic bearing materials,Paliers lisses — Essai de compression des matériaux antifriction,1981-12-01,1,['21.100.10'],ISO/TC 123/SC 2,9599,,"[83164,82987]","['en','fr']",4,"<p>This compression testing serves for the determination of the behaviour of metallic materials under uniaxial compression loading which ist uniformly distributed over the cross-section. For this purpose, a cylindrical specimen is subjected to compression which is slowly and continuously increased, and the compressive force used is measured.</p>"

10278,IS,,ISO 4386-1:1982,Plain bearings — Metallic multilayer plain bearings — Part 1: Non-destructive ultrasonic testing of bond for bearing metal layer thicknesses equal to or greater than 2 mm,"Paliers lisses — Paliers lisses métalliques multicouches — Partie 1: Détection, par la méthode ultrasonique, des défauts d'adhérence du matériau antifriction d'épaisseur égale ou supérieure à 2 mm",1982-02-01,1,['21.100.10'],ISO/TC 123,9599,,[10279],"['en','fr']",4,

10279,IS,,ISO 4386-1:1992,Plain bearings — Metallic multilayer plain bearings — Part 1: Non-destructive ultrasonic testing of bond,Paliers lisses — Paliers lisses métalliques multicouches — Partie 1: Contrôle non destructif aux ultrasons des défauts d'adhérence,1992-02-06,2,['21.100.10'],ISO/TC 123/SC 2,9599,[10278],"[45757,57028]","['en','fr']",10,<p>Specifies a testing method for determining bond defects between the bearing metal and the backing. Describes in detail only the pulse-echo method in which the probe is applied from the bearing metal side.</p>

57028,IS,,ISO 4386-1:2012,"Plain bearings — Metallic multilayer plain bearings — Part 1: Non-destructive ultrasonic testing of bond of thickness greater than or equal to 0,5 mm","Paliers lisses — Paliers lisses métalliques multicouches — Partie 1: Contrôle non destructif aux ultrasons des défauts d'adhérence d'épaisseur supérieure ou égale à 0,5 mm",2012-10-15,3,['21.100.10'],ISO/TC 123/SC 2,9599,[10279],[77223],['en'],9,"<p>ISO 4386-1:2012 specifies an ultrasonic testing method for determining bond defects between the bearing metal and the backing. The test can be performed on metallic multilayer plain bearings consisting of steel- or copper-based material backings lined with bearing metal

10280,IS,,ISO 4386-2:1982,Plain bearings — Metallic multilayer plain bearings — Part 2: Destructive testing of bond for bearing metal layer thicknesses greater than or equal to 2 mm,"Paliers lisses — Paliers lisses métalliques multicouches — Partie 2: Détermination, par essai destructif, de l'adhérence du matériau antifriction d'épaisseur supérieure ou égale à 2 mm",1982-02-01,1,['21.100.10'],ISO/TC 123/SC 2,9599,,"[45764,57029]","['en','fr']",4,"<p>Determines the bond strength between bearing metal and backing. The test can be applied to plain bearings consisting of backings of steel, cast iron or copper alloys and lined with a bearing metal layer based on lead, tin, copper, or aluminium. T

57029,IS,,ISO 4386-2:2012,Plain bearings — Metallic multilayer plain bearings — Part 2: Destructive testing of bond for bearing metal layer thicknesses greater than or equal to 2 mm,"Paliers lisses — Paliers lisses métalliques multicouches — Partie 2: Détermination, par essai destructif, de l'adhérence du matériau antifriction d'épaisseur supérieure ou égale à 2 mm",2012-10-15,2,['21.100.10'],ISO/TC 123/SC 2,9599,[10280],[77224],['en'],8,"<p>ISO 4386-2:2012 specifies a tensile test method for determination of the bond strength between the bearing metal and the backing. The test can be applied to multilayer plain bearings with bearing metals based on lead, tin, copper or aluminium. For tested

10281,IS,,ISO 4386-3:1992,Plain bearings — Metallic multilayer plain bearings — Part 3: Non-destructive penetrant testing,Paliers lisses — Paliers lisses métalliques multicouches — Partie 3: Contrôle non destructif par ressuage,1992-02-06,1,['21.100.10'],ISO/TC 123/SC 2,9599,,[68679],"['en','fr']",10,"<p>Describes safety precautions, preparation of test surface, application of penetrant, removal of excess penetrant, application of the developer, inspection, subsequent cleaning and the test report.</p>"

10282,IS,,ISO 4387:1987,Cigarettes — Determination of total and dry particulate matter using a routine analytical cigarette-smoking machine — Glass fibre filter smoke trap method,Cigarettes — Détermination du condensat de fumée brut et anhydre au moyen d'une machine à fumer analytique de routine pour cigarettes — Méthode par piégeage sur disque en fibre de verre,1987-04-09,1,['65.160'],ISO/TC 126,9599,,[10283],['fr'],,

10283,IS,,ISO 4387:1991,Cigarettes — Determination of total and nicotine-free dry particulate matter using a routine analytical smoking machine,Cigarettes — Détermination de la matière particulaire totale et de la matière anhydre et exempte de nicotine au moyen d'une machine à fumer analytique de routine,1991-10-17,2,['65.160'],ISO/TC 126,9599,[10282],[28323],"['en','fr']",14,

28323,IS,,ISO 4387:2000,Cigarettes — Determination of total and nicotine-free dry particulate matter using a routine analytical smoking machine,Cigarettes — Détermination de la matière particulaire totale et de la matière particulaire anhydre et exempte de nicotine au moyen d'une machine à fumer analytique de routine,2000-04-06,3,['65.160'],ISO/TC 126,9599,[10283],[76549],"['en','fr']",17,

46419,IS,Amd,ISO 4387:2000/Amd 1:2008,Cigarettes — Determination of total and nicotine-free dry particulate matter using a routine analytical smoking machine — Amendment 1,Cigarettes — Détermination de la matière particulaire totale et de la matière particulaire anhydre et exempte de nicotine au moyen d'une machine à fumer analytique de routine — Amendement 1,2008-09-08,3,['65.160'],ISO/TC 126,9599,,[76549],"['en','fr']",1,

72591,IS,Amd,ISO 4387:2000/Amd 2:2017,Cigarettes — Determination of total and nicotine-free dry particulate matter using a routine analytical smoking machine — Amendment 2,Cigarettes — Détermination de la matière particulaire totale et de la matière particulaire anhydre et exempte de nicotine au moyen d'une machine à fumer analytique de routine — Amendement 2,2017-09-28,3,['65.160'],ISO/TC 126,9599,,[76549],"['en','fr']",1,

10284,IS,,ISO 4388:1977,Tobacco and tobacco products — Determination of retention of coloured part of smoke condensate by cigarette filters — Direct spectrophotometric method,Tabac et produits du tabac — Détermination de la rétention de la partie colorée du condensat de fumée par les filtres de cigarettes — Méthode spectrophotométrique directe,1977-11-01,1,['65.160'],ISO/TC 126,9599,,[10285],"['en','fr']",3,

10286,IS,,ISO 4389:1981,Tobacco and tobacco products — Determination of organochlorine pesticide residues (Reference method),Tabac et produits du tabac — Détermination des résidus de pesticides organochlorés (Méthode de référence),1981-06-01,1,['65.160'],ISO/TC 126,9599,,[10287],"['en','fr']",6,

10287,IS,,ISO 4389:1997,Tobacco — Determination of organochlorine pesticide residues — Gas chromatographic method,Tabac — Dosage des résidus de pesticides organochlorés — Méthode par chromatographie en phase gazeuse,1997-12-25,2,['65.160'],ISO/TC 126,9599,[10286],[31178],"['en','fr']",14,

30957,IS,Cor,ISO 4389:1997/Cor 1:1998,Tobacco — Determination of organochlorine pesticide residues — Gas chromatographic method — Technical Corrigendum 1,Tabac — Dosage des résidus de pesticides organochlorés — Méthode par chromatographie en phase gazeuse — Rectificatif technique 1,1998-09-17,2,['65.160'],ISO/TC 126,9599,,[31178],"['en','fr']",2,

4453,IS,,ISO 439:1982,Steel and cast iron — Determination of total silicon — Gravimetric method,Aciers et fontes — Dosage du silicium total — Méthode gravimétrique,1982-08-01,1,['77.080'],ISO/TC 17/SC 1,9599,[4452],[4454],"['en','fr']",3,

4454,IS,,ISO 439:1994,Steel and iron — Determination of total silicon content — Gravimetric method,Aciers et fontes — Dosage du silicium total — Méthode gravimétrique,1994-03-17,2,['77.080.01'],ISO/TC 17/SC 1,9599,"[4452,4453]",[74714],"['en','fr']",6,"<p>The document specifies a gravimetric method for the determination of the total silicon content in steel and iron. The method is apllicable to silicon contents between 0,10 % (m/m) and 5,0 % (m/m). For samples containing molybdenum, niobium, tantalum, titanium, tungsten, zirconium or high levels of chromium, the result are less precise than for unalloyed steels.</p>"

10290,IS,,ISO 4392-1:1988,Hydraulic fluid power — Determination of characteristics of motors — Part 1: At constant low speed and at constant pressure,Transmissions hydrauliques — Détermination des caractéristiques des moteurs — Partie 1: Essai à pression constante et basse vitesse constante,1988-04-21,1,['23.100.10'],ISO/TC 131/SC 8,9599,,[10291],"['en','fr']",,

10291,IS,,ISO 4392-1:1989,Hydraulic fluid power — Determination of characteristics of motors — Part 1: At constant low speed and at constant pressure,Transmissions hydrauliques — Détermination des caractéristiques des moteurs — Partie 1: Essai à pression constante et basse vitesse constante,1989-08-10,2,['23.100.10'],ISO/TC 131/SC 8,9599,[10290],[34762],"['en','fr']",7,"<p>This part describes a method of determining the characteristics of motors, of either fixed or variable displacement types. The accuracy of measurements is divided into 3 classes, A, B, and C which are explained in annex A. Figure 1 shows a typical test circuit for bidirectional motor. The informative annex B contains the b

10292,IS,,ISO 4392-2:1988,Hydraulic fluid power — Determination of characteristics of motors — Part 2: Startability,Transmissions hydrauliques — Détermination des caractéristiques des moteurs — Partie 2: Essai de démarrage,1988-03-31,1,['23.100.10'],ISO/TC 131/SC 8,9599,,[10293],"['en','fr']",,

10293,IS,,ISO 4392-2:1989,Hydraulic fluid power — Determination of characteristics of motors — Part 2: Startability,Transmissions hydrauliques — Détermination des caractéristiques des moteurs — Partie 2: Essai de démarrage,1989-08-10,2,['23.100.10'],ISO/TC 131/SC 8,9599,[10292],[34763],"['en','fr']",10,"<p>This part specifies two test methods for hydraulic motors. Describes two comparable methods of measurement, namely the constant torque method and the constant pressure method. The accuracy of measurements is divided into 3 classes, A, B, and C which are explained in the normative annex A. The normative annex B includes the classes of measurement accuracy, and the normative annex C contains

10295,IS,,ISO 4393:1978,Fluid power systems and components — Cylinders — Basic series of piston strokes,Transmissions hydrauliques et pneumatiques — Vérins — Série de base de courses de piston,1978-09-01,1,['23.100.20'],ISO/TC 131/SC 3,9599,,"[64053,59470,61355]","['en','fr']",2,"<p>It specifies the preferred series of piston strokes for application to single-acting and double-acting, hydraulic and pneumatic fluid power cylinders. The figure shows the identification of piston strokes. It tabulates piston strokes from 25 mm up to and including 500 mm. If an extension of the series shown is required, use the rounded-off R 10 series of values as shown in ISO 497.</p>"

10296,IS,,ISO 4394-1:1980,Fluid power systems and components — Cylinder barrels — Part 1: Requirements for steel tubes with specially finished bores,Transmissions hydrauliques et pneumatiques — Tubes pour vérins — Partie 1: Caractéristiques des tubes en acier à alésage de finition spéciale,1980-09-01,1,['23.100.20'],ISO/TC 131/SC 3,9599,,[10297],"['en','fr']",9,"<p>This part covers only one specific type of steel tubing suitable for fluid power cylinders. Specifies the mechanical properties, dimensional tolerances, surface finishes, and technical delivery conditions for round steel tubes, seamless or welded type, and defines the tube dimensions by inside diameter and thickness, or inside dia

10298,IS,,ISO 4395:1978,Fluid power systems and components — Cylinders — Piston rod thread dimensions and types,Transmissions hydrauliques et pneumatiques — Vérins — Dimensions et types de filetage des tiges de piston,1978-09-01,1,['23.100.20'],ISO/TC 131/SC 3,9599,,[44086],"['en','fr']",2,"<p>Establishes a basic series for piston rod threads for application to fluid power cylinders. Specifies thread dimensions and configurations to be used with hydraulic and pneumatic fluid power piston rod ends. Gives definitions, and the figures 1 to 3 show female threads, shouldered male threads, and unshouldered male threads. The table contains thread sizes from M3 x 0,35 up to and including M280 x 6.</

10300,IS,,ISO 4397:1978,Fluid power systems and components — Connectors and associated components — Outside diameters of tubes and inside diameters of hoses,Transmissions hydrauliques et pneumatiques — Raccords et éléments associés — Diamètres extérieurs des tubes et diamètres intérieurs des tuyaux flexibles,1978-02-01,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[10301],"['en','fr']",1,

10301,IS,,ISO 4397:1993,Fluid power systems and components — Connectors and associated components — Nominal outside diameters of tubes and nominal inside diameters of hoses,Transmissions hydrauliques et pneumatiques — Raccords et éléments associés — Diamètres extérieurs nominaux des tubes et diamètres intérieurs nominaux des tuyaux flexibles,1993-02-11,2,['23.100.40'],ISO/TC 131/SC 4,9599,[10300],"[10299,50099]","['en','fr']",2,"<p>Specifies two series of diameters: a series of nominal outside diameters for rigid or semi-rigid tubes, irrespective of material composition, and a series of nominal inside diameters for hoses made of rubber or plastic.</p>"

10302,IS,,ISO 4399:1977,Fluid power systems and components — Connectors and associated components — Nominal pressures,Transmissions hydrauliques et pneumatiques — Raccords et éléments associés — Pressions nominales,1977-09-01,1,['23.100.40'],ISO/TC 131/SC 4,9599,,[22769],"['en','fr']",1,

22769,IS,,ISO 4399:1995,Fluid power systems and components — Connectors and associated components — Nominal pressures,Transmissions hydrauliques et pneumatiques — Raccords et composants associés — Pressions nominales,1995-04-27,2,['23.100.40'],ISO/TC 131/SC 4,9599,[10302],[74791],"['en','fr']",2,<p>Cancels and replaces the first edition (1977). Specifies a selection of nominal pressures for hydraulic and pneumatic fluid power connectors and associated components.</p>

10303,IS,,ISO 4400:1980,Fluid power systems and components — Three-pin electrical plug connector — Characteristics and requirements,Transmissions hydrauliques et pneumatiques — Connecteurs électriques à trois broches — Caractéristiques et exigences,1980-12-01,1,['23.100.99'],ISO/TC 131,9599,,[10304],"['en','fr']",4,

10304,IS,,ISO 4400:1985,Fluid power systems and components — Three-pin electrical plug connector — Characteristics and requirements,Transmissions hydrauliques et pneumatiques — Connecteurs électriques à trois broches — Caractéristiques et exigences,1985-11-21,2,['23.100.99'],ISO/TC 131/SC 3,9599,[10303],[20509],"['en','fr']",4,

10305,IS,,ISO 4401:1980,Hydraulic fluid power — Four-port directional control valves — Mounting surfaces,Transmissions hydrauliques — Distributeurs à quatre orifices — Plan de pose,1980-05-01,1,['23.100.50'],ISO/TC 131/SC 5,9599,,[10306],"['en','fr']",8,

10306,IS,,ISO 4401:1994,Hydraulic fluid power — Four-port directional control valves — Mounting surfaces,Transmissions hydrauliques — Distributeurs à quatre orifices — Plan de pose,1994-12-15,2,['23.100.50'],ISO/TC 131/SC 5,9599,[10305],[33366],"['en','fr']",18,<p>Cancels and replaces the first edition (1980). Specifies the dimensions and other data relating to surfaces on which four-port hydraulic directional control valves are mounted in order to ensure their interchangeability. Applies to mounting surfaces of these valves which represent current practice.</p>

10308,IS,,ISO 4402:1991,Hydraulic fluid power — Calibration of automatic-count instruments for particles suspended in liquids — Method using classified AC Fine Test Dust contaminant,Transmissions hydrauliques — Étalonnage des compteurs automatiques de particules en suspension dans les liquides — Méthode utilisant une fine poussière d'essai (ACFTD),1991-10-17,2,['23.100.60'],ISO/TC 131/SC 6,9599,,[1919],"['en','fr']",6,

35505,IS,,ISO 4404-1:2001,Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids — Part 1: Water-containing fluids,Pétrole et produits connexes — Détermination de la résistance à la corrosion de fluides hydrauliques difficilement inflammables — Partie 1: Fluides contenant de l'eau,2001-12-13,1,['75.120'],ISO/TC 28,9599,[10309],[52151],"['en','fr']",12,

10309,IS,,ISO 4404:1998,Petroleum and related products — Determination of the corrosion resistance of water-containing fire-resistant fluids for hydraulic systems,"Pétrole et produits connexes — Détermination du pouvoir anticorrosif des fluides difficilement inflammables contenant de l'eau, pour les systèmes hydrauliques",1998-06-04,1,['75.120'],ISO/TC 28,9599,,"[35505,35857]","['en','fr']",11,

35857,IS,,ISO 4404-2:2003,Petroleum and related products — Determination of the corrosion resistance of fire-resistant hydraulic fluids — Part 2: Non-aqueous fluids,Pétrole et produits connexes — Détermination de la résistance à la corrosion de fluides hydrauliques difficilement inflammables — Partie 2: Fluides non aqueux,2003-07-31,1,['75.120'],ISO/TC 28,9599,[10309],[56542],"['en','fr']",6,"<p>ISO 4404-2:2003 specifies a procedure for the determination of the corrosion-inhibiting properties of non-aqueous hydraulic fluids within the category HFD, as classified in ISO 6743-4. </p><p>It provides a qualitative assessment of corrosion of five of the most common metals used in the construction

10310,IS,,ISO 4405:1991,Hydraulic fluid power — Fluid contamination — Determination of particulate contamination by the gravimetric method,Transmissions hydrauliques — Pollution des fluides — Détermination de la pollution particulaire par la méthode gravimétrique,1991-05-09,1,['23.100.60'],ISO/TC 131/SC 6,9599,,"[79715,35029,50157]","['en','fr']",4,

10311,IS,,ISO 4406:1987,Hydraulic fluid power — Fluids — Method for coding level of contamination by solid particles,Transmissions hydrauliques — Fluides — Méthode de codification du niveau de pollution par particules solides,1987-11-26,1,"['75.120','23.100.60']",ISO/TC 131/SC 8,9599,,[21463],"['en','fr']",4,

21463,IS,,ISO 4406:1999,Hydraulic fluid power — Fluids — Method for coding the level of contamination by solid particles,Transmissions hydrauliques — Fluides — Méthode de codification du niveau de pollution particulaire solide,1999-12-02,2,"['75.120','23.100.60']",ISO/TC 131/SC 6,9599,[10311],[72618],"['en','fr']",7,

72618,IS,,ISO 4406:2017,Hydraulic fluid power — Fluids — Method for coding the level of contamination by solid particles,Transmissions hydrauliques — Fluides — Méthode de codification du niveau de pollution particulaire solide,2017-08-08,3,"['75.120','23.100.60']",ISO/TC 131/SC 6,9599,[21463],[79716],['en'],6,<p>ISO 4406:2017 specifies the code to be used in defining the quantity of solid particles in the fluid used in a given hydraulic fluid power system.</p>

10312,IS,,ISO 4407:1991,Hydraulic fluid power — Fluid contamination — Determination of particulate contamination by the counting method using a microscope,Transmissions hydrauliques — Pollution des fluides — Détermination de la pollution particulaire solide — Méthode de comptage au microscope,1991-06-06,1,['23.100.60'],ISO/TC 131/SC 6,9599,,[28058],"['en','fr']",6,

28058,IS,,ISO 4407:2002,Hydraulic fluid power — Fluid contamination — Determination of particulate contamination by the counting method using an optical microscope,Transmissions hydrauliques — Pollution des fluides — Détermination de la pollution particulaire par comptage au microscope optique,2002-05-02,2,['23.100.60'],ISO/TC 131/SC 6,9599,[10312],"[77353,86030]","['en','fr']",14,"<p>This International Standard specifies methods for determining the level of particulate contamination in liquids used in hydraulic systems by counting the number of particles deposited on the surface of a membrane filter using an optical microscope. It includes particle counting by two manual methods and image a

10314,IS,,ISO 4409:1986,"Hydraulic fluid power — Positive displacement pumps, motors and integral transmissions — Determination of steady-state performance","Transmissions hydrauliques — Pompes, moteurs et variateurs volumétriques — Détermination du fonctionnement en régime permanent",1986-10-09,1,['23.100.10'],ISO/TC 131/SC 8,9599,,[37528],"['en','fr']",15,"<p>Specifies methods for determining the performance and efficiency of equipment, and applies to components having continuously rotating shafts. Describes requirements for test installations, test procedures, and the presentation of test results. Annex A gives guidance as to the use of practical units, annex B contains information on err

37528,IS,,ISO 4409:2007,"Hydraulic fluid power — Positive-displacement pumps, motors and integral transmissions — Methods of testing and presenting basic steady state performance","Transmissions hydrauliques — Pompes, moteurs et variateurs volumétriques — Méthodes d'essai et de présentation des données de base du fonctionnement en régime permanent",2007-03-29,2,['23.100.10'],ISO/TC 131/SC 8,9599,[10314],"[68410,57406]","['en','fr']",23,"<p>ISO 4409:2007 specifies methods for determining the performance and efficiency of hydraulic fluid power positive displacement pumps, motors and integral transmissions. It applies to components having continuously rotating shafts.</p><p>ISO 4409:2007 specif

4456,IS,,ISO 441:1978,Textile machinery and accessories — Drop wires for mechanical and electrical warp stop motions,Matériel pour l'industrie textile — Lamelles pour casse-chaînes mécaniques et électriques,1978-07-01,1,['59.120.30'],ISO/TC 72/SC 3,9599,,[4457],"['en','fr']",5,

10315,IS,,ISO 4411:1986,Hydraulic fluid power — Valves — Determination of pressure differential/flow characteristics,Transmissions hydrauliques — Appareils de distribution — Détermination des caractéristiques pression différentielle/débit,1986-08-28,1,['23.100.50'],ISO/TC 131/SC 5,9599,,"[28056,43559]","['en','fr']",11,"<p>Specifies determination methods, requirements for test installations, procedures, and presentation of results. May also be applied to other fluid power components where similar conditions apply. Accuracy of measurement is divided into three classes (A,B, and C) which are explained in annex A. Pipe loss is given in annex B. Guidance as to the use of practical units for the

43559,IS,,ISO 4411:2008,Hydraulic fluid power — Valves — Determination of pressure differential/flow characteristics,Transmissions hydrauliques — Distributeurs — Détermination des caractéristiques de pression différentielle/débit,2008-09-29,2,['23.100.50'],ISO/TC 131/SC 5,9599,[10315],[67811],"['en','fr']",9,"<p>ISO 4411:2008 specifies methods for determining, under steady-state conditions, the pressure differential caused by the flow through any given path in a hydraulic fluid power valve. Requirements for test installations, procedures and presentation of results are specified.</p>"

10316,IS,,ISO 4412-1:1979,Hydraulic fluid power — Test code for the determination of airborne noise levels — Part 1: Pumps,Transmissions hydrauliques — Code d'essai pour la détermination du niveau de bruit aérien — Partie 1: Pompes,1979-11-01,1,"['23.100.10','17.140.20']",ISO/TC 131/SC 8,9599,,[10317],"['en','fr']",6,

10318,IS,,ISO 4412-2:1984,Hydraulic fluid power — Test code for the determination of airborne noise levels — Part 2: Motors,Transmissions hydrauliques — Code d'essai pour la détermination du niveau de bruit aérien — Partie 2: Moteurs,1984-05-01,1,"['23.100.10','17.140.20']",ISO/TC 131/SC 8,9599,,[10319],"['en','fr']",6,

10322,IS,,ISO 4413:1979,Hydraulic fluid power — General rules for the application of equipment to transmission and control systems,Transmissions hydrauliques — Règles générales pour l'installation et l'utilisation d'équipements dans les systèmes de transmission et de commande,1979-02-01,1,['23.100.01'],ISO/TC 131/SC 9,9599,[10321],[21935],"['en','fr']",17,

21935,IS,,ISO 4413:1998,Hydraulic fluid power — General rules relating to systems,Transmissions hydrauliques — Règles générales relatives aux systèmes,1998-08-27,2,['23.100.01'],ISO/TC 131/SC 9,9599,[10322],[44781],"['en','fr']",68,

10324,IS,,ISO 4414:1982,Pneumatic fluid power — Recommendations for the application of equipment to transmission and control systems,Transmissions pneumatiques — Règles générales pour l'installation et l'utilisation d'équipements dans les systèmes de transmission et de commande,1982-09-01,1,['23.100.01'],ISO/TC 131/SC 9,9599,[10323],[21937],"['en','fr']",25,

21937,IS,,ISO 4414:1998,Pneumatic fluid power — General rules relating to systems,Transmissions pneumatiques — Règles générales relatives aux systèmes,1998-08-27,2,['23.100.01'],ISO/TC 131/SC 9,9599,[10324],[44790],"['en','fr']",57,

10325,IS,,ISO 4415:1981,"Size designation of clothes — Men's and boys' underwear, nightwear and shirts","Désignation des tailles de vêtements — Sous-vêtements, vêtements de nuit et chemises pour hommes et garçons",1981-07-01,1,['61.020'],ISO/TC 133,9599,,[64075],"['en','fr']",5,"<p>Cancels and replaces the clause 4, control dimensions, a) to e). Deletion of the parts b) and c) of figure 1 and of the parts b) and c) of figure 2 and insertion of the revised wording.</p>"

10326,IS,Cor,ISO 4415:1981/Cor 1:1990,"Size designation of clothes — Men's and boys' underwear, nightwear and shirts — Technical Corrigendum 1","Désignation des tailles de vêtements — Sous-vêtements, vêtements de nuit et chemises pour hommes et garçons — Rectificatif technique 1",1990-11-05,1,['61.020'],ISO/TC 133,9599,,[64075],"['en','fr']",3,"<p>Cancels and replaces the clause 4, control dimensions, a) to e). Deletion of the parts b) and c) of figure 1 and of the parts b) and c) of figure 2 and insertion of the revised wording.</p>"

10327,IS,,ISO 4416:1981,"Size designation of clothes — Women's and girls' underwear, nightwear, foundation garments and shirts","Désignation des tailles de vêtements — Sous-vêtements, vêtements de nuit et de maintien et chemisiers pour femmes et filles",1981-07-01,1,['61.020'],ISO/TC 133,9599,,[64075],"['en','fr']",5,"<p>Establishes a system of designating the sizes of the above mentioned garments that are classified as a) covering the upper body only, or b) covering the whole body, or c) covering the lower body only, and applies to civilian and uniform garments. Both the control dimensions on which the size designation system is based, and the method of indicating the size designation on a

10328,IS,Cor,ISO 4416:1981/Cor 1:1990,"Size designation of clothes — Women's and girls' underwear, nightwear, foundation garments and shirts — Technical Corrigendum 1","Désignation des tailles de vêtements — Sous-vêtements, vêtements de nuit et de maintien et chemisiers pour femmes et filles — Rectificatif technique 1",1990-10-12,1,['61.020'],ISO/TC 133,9599,,[64075],"['en','fr']",2,

10329,IS,,ISO 4417:1977,Size designation of clothes — Headwear,Désignation des tailles des vêtements — Couvre-chefs,1977-12-01,1,"['61.020','61.040']",ISO/TC 133,9599,,[64075],"['en','fr']",2,"<p>Establishes a system of designating the size of headwear based on body and not garment measurements. Specifies the control dimensions (headgirth), the size designation and the labelling.</p>"

10330,IS,,ISO 4418:1978,Size designation of clothes — Gloves,Désignation des tailles de vêtements — Gants,1978-09-01,1,"['61.020','61.040']",ISO/TC 133,9599,,[64075],"['en','fr']",2,"<p>The size designation system is based on body and not garment measurements. Both the control dimensions on which the size designation is based, and the method of indicating the size designation on a garment label, are laid down. Should be read in conjunction with ISO 3635</p>"

21096,IS,,ISO 4422-1:1996,Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Part 1: General,Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) pour l'adduction d'eau — Spécifications — Partie 1: Généralités,1996-12-26,1,"['23.040.45','93.025','23.040.20','91.140.60']",ISO/TC 138/SC 2,9599,"[10331,10332]",[50361],"['en','fr']",3,"<p>Specifies the general aspects of pipes, joints, fittings and ancillaries, made of unplasticized poly(vinyl chloride) (PVC-U), for piping systems intended to be used for buried water mains and for water supplies above ground, both inside and outside buildings. Replaces ISO 4422:1990.</p>" 2109

10331,IS,,ISO 4422:1990,Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications,Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) pour l'adduction d'eau — Spécifications Tubes et raccords en poly (chlorure de vinyle) non plastifié (PVC-U) pour l'adduction d'eau — Spécifications,1990-08-30,1,"['91.140.60','83.140.30']",ISO/TC 138/SC 2,9599,,"[21096,22385,22386,22384,25967]","['en','fr']",8,

10332,IS,Amd,ISO 4422:1990/Amd 1:1992,Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Amendment 1,Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) pour l'adduction d'eau — Spécifications Tubes et raccords en poly (chlorure de vinyle) non plastifié (PVC-U) pour l'adduction d'eau — Spécifications — Amendement 1,1992-10-29,1,"['91.140.60','83.140.30']",ISO/TC 138/SC 2,9599,,"[21096,22385,22386,22384,25967]","['en','fr']",1,

22384,IS,,ISO 4422-2:1996,Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Part 2: Pipes (with or without integral sockets),Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) pour l'adduction d'eau — Spécifications — Partie 2: Tubes (avec ou sans emboîtures incorporées),1996-12-12,1,"['23.040.45','93.025','23.040.20','91.140.60']",ISO/TC 138/SC 2,9599,"[10331,10332]",[50362],"['en','fr']",7,"<p>Gives the characteristics and properties of extruded pipes made of unplastized polyvinyl chloride (PVC-U), with or without socket(s) and intended to be used for buried water mains and services and for water supply above ground b

22385,IS,,ISO 4422-3:1996,Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply — Specifications — Part 3: Fittings and joints,Tubes et raccords en poly(chlorure de vinyle) non plastifié (PVC-U) pour l'adduction d'eau — Spécifications — Partie 3: Raccords et assemblages,1996-12-26,1,"['23.040.45','93.025','23.040.20','91.140.60']",ISO/TC 138/SC 2,9599,"[10331,10332]",[50363],"['en','fr']",4,"<p>Specifies the characteristics and properties of fittings (injection-moulded and postformed) and joints made of unplasticized poly(vinyl chloride) (PVC-U), to be used for buried water mains and for water supplies above ground, both inside and outside buildings.</p>" 223