Withdrawn and superseded ISO standards — page 64 of 246

60765,IS,,ISO 17842-2:2015,Safety of amusement rides and amusement devices — Part 2: Operation and use,Sécurité des manèges et des dispositifs de divertissement — Partie 2: Fonctionnement et utilisation,2015-04-08,1,['97.200.40'],ISO/TC 254,9599,,[79457],['en'],23,"<p>ISO 17842-2:2015 specifies the minimum requirements necessary to ensure the safe maintenance, operation, inspection and testing of the following: mobile, temporary or permanently installed machinery and structures, e.g. roundabouts, swings, boats, Ferris wheels, roller coasters, chutes, grandstands, membrane or textile structures, booths, stages, side shows, and structures for artistic aerial displays. These devices are intende

65649,IS,,ISO 17842-3:2015,"Safety of amusement rides and amusement devices — Part 3: Requirements for inspection during design, manufacture, operation and use","Sécurité des manèges et des dispositifs de divertissement — Partie 3: Exigences relatives à l'inspection pendant la conception, fabrication et fonctionnement",2015-06-24,1,['97.200.40'],ISO/TC 254,9599,,[73053],['en'],7,"<p>ISO 17842-3:2015 defines requirements for the necessary inspections, in accordance with ISO/IEC 17020, of amusement devices designed, manufactured, operated and used according to ISO 17842 1 and ISO 17842 2.</p>"

31591,IS,,ISO 17853:2003,"Wear of implant materials — Polymer and metal wear particles — Isolation, characterization and quantification","Usure des matériaux d'implant — Particules d'usure des polymères et des métaux — Isolation, caractérisation et quantification",2003-07-03,1,['11.040.40'],ISO/TC 150/SC 4,9599,,[50746],['en'],8,"<p>ISO 17853:2003 specifies methods for sampling wear debris generated by total joint prostheses in humans and in joint simulators. It specifies the apparatus, reagents and test methods to isolate, characterize and quantify both polymer and metal wear debris from samples of tissue excised from around the joint prosthesis, obtained at revision surgery or post mortem,

40191,IS,Cor,ISO 17853:2003/Cor 1:2004,"Wear of implant materials — Polymer and metal wear particles — Isolation, characterization and quantification — Technical Corrigendum 1","Usure des matériaux d'implant — Particules d'usure des polymères et des métaux — Isolation, caractérisation et quantification — Rectificatif technique 1",2004-02-09,1,['11.040.40'],ISO/TC 150/SC 4,9599,,[50746],['en'],1,

50746,IS,,ISO 17853:2010,Wear of implant materials — Polymer and metal wear particles — Isolation and characterization,"Usure des matériaux d'implant — Particules d'usure des polymères et des métaux — Isolation, caractérisation et quantification",2010-06-07,2,['11.040.40'],ISO/TC 150/SC 4,9599,"[40191,31591]",[57230],['en'],15,"<p>ISO 17853:2010 specifies methods for sampling wear particles generated by joint implants in humans and in joint simulators. It specifies the apparatus, reagents and test methods to isolate and characterize both polymer and metal wear particles from samples of tissue excised from around the joint implant, obtained at revision surgery or post mortem, and from samples

66827,IS,,ISO 17855-2:2016,Plastics — Polyethylene (PE) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties,Plastiques — Polyéthylène (PE) pour moulage et extrusion — Partie 2: Préparation des éprouvettes et détermination des propriétés,2016-02-15,1,['83.080.20'],ISO/TC 61/SC 9,9599,[38243],[83766],"['en','fr']",9,"<p>ISO 17855-2:2016 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polyethylene (PE) moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are g

60837,IS,,ISO 17862:2013,Surface chemical analysis — Secondary ion mass spectrometry — Linearity of intensity scale in single ion counting time-of-flight mass analysers,Analyse chimique des surfaces — Spectrométrie de masse des ions secondaires — Linéarité de l'échelle d'intensité des analyseurs de masse à temps de vol pour comptage des ions individuels,2013-12-10,1,['71.040.40'],ISO/TC 201/SC 6,9599,,[80457],['en'],25,<p>ISO 17862:2014 specifies a method for determining the maximum count rate for an acceptable limit of divergence from linearity of the intensity scale in single ion counting time-of-flight (TOF) secondary ion mass spectrometers using a test based on isotopic ratios in spectra

45820,IS,,ISO 17867:2015,Particle size analysis — Small-angle X-ray scattering,Analyse granulométrique — Diffusion des rayons X aux petits angles,2015-04-24,1,['19.120'],ISO/TC 24/SC 4,9599,,[69213],['en'],23,"<p>Small-angle X-ray scattering (SAXS) is a well-established technique that allows structural information to be obtained about inhomogeneities in materials with a characteristic length from 1 nm to 100 nm. Under certain conditions (narrow size distributions, appropriate instrumental configuration, and idealised shape) the limit of 100 nm can be significantly extended. ISO 17687:2015 specifies a method for the application of SAXS to the estimation of mean particle sizes in dilute disper

6419,IS,,ISO 1787:1972,Cinematography — Camera usage of 8 mm motion- picture film perforated Type S,"Cinématographie — Position du film 8 mm perforé, type S, dans le couloir de la caméra",1972-03-01,1,['37.060.10'],ISO/TC 36,9599,,[6420],"['en','fr']",1,

60884,IS,,ISO 17871:2015,Gas cylinders — Quick-release cylinder valves — Specification and type testing,Bouteilles à gaz — Robinets de bouteilles à ouverture rapide — Spécifications et essais de type,2015-08-10,1,['23.020.35'],ISO/TC 58/SC 2,9599,,[74687],"['en','fr']",7,"<p>ISO 17871:2015 in conjunction with ISO 10297:2014 and ISO 14246:2014 specifies design, type testing, marking and manufacturing tests, and examinations requirements for quick-release cylinder valves intended to be fitted to refillable transportable gas cylinders which convey non-toxic, non-oxidizing, and non-corrosive compressed or liquefied gases or extinguishing agents charged with compressed gases to be used for fire-e

73160,IS,Amd,ISO 17871:2015/Amd 1:2018,Gas cylinders — Quick-release cylinder valves — Specification and type testing — Amendment 1,Bouteilles à gaz — Robinets de bouteilles à ouverture rapide — Spécifications et essais de type — Amendement 1,2018-07-24,1,['23.020.35'],ISO/TC 58/SC 2,9599,,[74687],"['en','fr']",1,

38508,IS,,ISO 17872:2007,Paints and varnishes — Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing,Peintures et vernis — Lignes directrices pour la production de rayures au travers du revêtement de panneaux métalliques en vue des essais de corrosion,2007-02-15,1,['87.040'],ISO/TC 35/SC 9,9599,,[71590],"['en','fr','ru']",10,"<p>ISO 17872:2007 describes methods of scribing coated steel or test-pieces for corrosion tests, where the coating system is applied at dry film thicknesses of less than 500 micrometres. It is intended as a guideline only, being based on the results of a collaborative trial with no subsequent corrosion testing having

36506,IS,,ISO 17874-1:2004,Remote handling devices for radioactive materials — Part 1: General requirements,Dispositifs de manipulation à distance pour matériaux radioactifs — Partie 1: Exigences générales,2004-03-12,1,['13.280'],ISO/TC 85/SC 2,9599,,[52156],"['en','fr']",26,<p>ISO 17874-1:2004 describes requirements concerning devices for remote handling of radioactive materials.</p>

60932,IS,,ISO 17885:2015,Plastics piping systems — Mechanical fittings for pressure piping systems — Specifications,Systèmes de canalisations en plastiques — Raccords mécaniques pour les canalisations sous pression — Spécifications,2015-09-02,1,"['23.040.45','75.200']",ISO/TC 138/SC 4,9599,"[18875,18874,23941,32238]",[77001],"['en','fr']",41,"<p>ISO 17885:2015 specifies the requirements and test methods for mechanical fittings intended to join plastic pressure piping systems including transition fittings to metal pipes for the following:</p><p>? supply of gaseous fuels (GAS);</p><p>? supply of water for human consumption (W), including raw water prior to treatment and for the supply of w

70666,IS,Amd,ISO 17885:2015/Amd 1:2016,Plastics piping systems — Mechanical fittings for pressure piping systems — Specifications — Amendment 1,Systèmes de canalisations en plastiques — Raccords mécaniques pour les canalisations sous pression — Spécifications — Amendement 1,2016-07-28,1,"['23.040.45','75.200']",ISO/TC 138/SC 4,9599,,[77001],"['en','fr']",2,

6421,IS,,ISO 1789:1973,Withdrawal of ISO 1789-1973,Annulation de l'ISO 1789-1973,1973-11-01,1,['91.010.30'],ISO/TC 59,9599,,[12893],"['en','fr']",1,

31620,IS,,ISO 17895:2005,Paints and varnishes — Determination of the volatile organic compound content of low-VOC emulsion paints (in-can VOC),Peintures et vernis — Détermination de la teneur en composés organiques volatils dans les peintures émulsions à faible teneur en COV (COV en emballage),2005-03-17,1,['87.040'],ISO/TC 35,9599,,"[82479,60415]","['en','fr','ru']",11,"<p>ISO 17895:2005 specifies a gas-chromatographic method of quantitatively determining the volatile organic compound (VOC) content (i.e. the content of organic compounds with boiling points up to 250 °C) under standard conditions (101,325 kPa) of low VOC content emulsion paints (in-can VOC). The method is applicable to VOC c

26801,IS,,ISO 179-1:2000,Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test,Plastiques — Détermination des caractéristiques au choc Charpy — Partie 1: Essai de choc non instrumenté,2000-12-07,1,['83.080.01'],ISO/TC 61/SC 2,9599,"[22872,4018]",[44852],"['en','fr']",17,

39017,IS,Amd,ISO 179-1:2000/Amd 1:2005,Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test — Amendment 1,Plastiques — Détermination des caractéristiques au choc Charpy — Partie 1: Essai de choc non instrumenté — Amendement 1,2005-08-16,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[44852],"['en','fr']",1,

44852,IS,,ISO 179-1:2010,Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test,Plastiques — Détermination des caractéristiques au choc Charpy — Partie 1: Essai de choc non instrumenté,2010-06-04,2,['83.080.01'],ISO/TC 61/SC 2,9599,"[39017,26801]",[84393],"['en','fr','ru']",22,"<p>ISO 179-1:2010 specifies a method for determining the Charpy impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.</p><p>The method can be used to investigate the behaviour of spec

84393,IS,,ISO 179-1:2023,Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test,Plastiques — Détermination des caractéristiques au choc Charpy — Partie 1: Essai de choc non instrumenté,2023-06-01,3,['83.080.01'],ISO/TC 61/SC 2,9599,[44852],[91071],"['en','fr']",22,"<p class='MsoBodyText'><span lang='EN-GB'>This document specifies a method for determining the Charpy impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.</span></p><p class='MsoBodyText'><span l

4017,IS,,ISO 179:1982,Plastics — Determination of Charpy impact strength of rigid materials,Plastiques — Détermination de la résistance au choc Charpy des matières rigides,1982-12-01,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[4018],"['en','fr']",9,

4018,IS,,ISO 179:1993,Plastics — Determination of Charpy impact strength,Plastiques — Détermination de la résistance au choc Charpy,1993-05-06,2,['83.080.01'],ISO/TC 61/SC 2,9599,[4017],[26801],"['en','fr']",12,

22872,IS,Cor,ISO 179:1993/Cor 1:1994,Plastics — Determination of Charpy impact strength — Technical Corrigendum 1,Plastiques — Détermination de la résistance au choc Charpy — Rectificatif technique 1,1994-01-27,2,['83.080.01'],ISO/TC 61/SC 2,9599,,[26801],['fr'],,

22950,IS,,ISO 179-2:1997,Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test,Plastiques — Détermination des caractéristiques au choc Charpy — Partie 2: Essai de choc instrumenté,1997-12-18,1,['83.080.01'],ISO/TC 61/SC 2,9599,,"[44860,75825,38234]","['en','fr']",17,

50484,IS,Amd,ISO 179-2:1997/Amd 1:2011,Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test — Amendment 1: Precision data,Plastiques — Détermination des caractéristiques au choc Charpy — Partie 2: Essai de choc instrumenté — Amendement 1: Données de fidélité,2011-06-22,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[75825],"['en','fr']",2,

31162,IS,Cor,ISO 179-2:1997/Cor 1:1998,Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test — Technical Corrigendum 1,Plastiques — Détermination des caractéristiques au choc Charpy — Partie 2: Essai de choc instrumenté — Rectificatif technique 1,1998-11-19,1,['83.080.01'],ISO/TC 61/SC 2,9599,,"[44860,75825,38234]","['en','fr']",1,

6423,IS,,ISO 1791:1983,Building construction — Modular co-ordination — Vocabulary,Construction immobilière — Coordination modulaire — Vocabulaire,1983-12-01,2,"['01.040.91','91.010.30']",ISO/TC 59/SC 2,9599,,[77077],"['en','fr']",6,<p>Defines terms necessary for the design and construction of buildings in accordance with the principles and rules of modular coordination laid down in ISO 2848 and for the design and manufacture of components for use in such buildings in English and French.</p>

6424,IS,,ISO 1793:1975,Cinematography — Reels for 16 mm motion-picture projectors (up to and including 120 m capacity : 18 cm size) — Dimensions,Cinématographie — Bobines de projection pour film cinématographique 16 mm (capacité maximale : 120 m pour le format 18 cm) — Dimensions,1975-07-01,1,['37.060.10'],ISO/TC 36,9599,,"[36142,20576]","['en','fr']",4,

38532,IS,,ISO 17932:2005,Animal and vegetable fats and oils — Determination of the deterioration of bleachability index (DOBI),Corps gras d'origines animale et végétale — Détermination de la détérioration de l'indice de blanchiment (DOBI),2005-10-28,1,['67.200.10'],ISO/TC 34/SC 11,9599,,[54401],"['en','fr','ru']",6,<p>ISO 17932:2005 specifies a method for the determination of the deterioration of bleachability index (DOBI) of crude palm oil. It is not applicable to oils with significant levels of chlorophylls.</p>

6426,IS,,ISO 1795:1974,Raw rubber in bales — Sampling,Caoutchouc brut en balles — Échantillonnage,1974-03-01,1,['83.040.10'],ISO/TC 45,9599,[4144],[6427],"['en','fr']",1,

6427,IS,,ISO 1795:1992,"Rubber, raw, natural and synthetic — Sampling and further preparative procedures","Caoutchouc brut, naturel et synthétique — Méthodes d'échantillonnage et de préparation ultérieure",1992-08-12,2,['83.040.10'],ISO/TC 45/SC 3,9599,"[6426,7607,6428]",[31520],"['en','fr']",3,

31520,IS,,ISO 1795:2000,"Rubber, raw natural and raw synthetic — Sampling and further preparative procedures","Caoutchouc, naturel brut et synthétique brut — Méthodes d'échantillonnage et de préparation ultérieure",2000-07-27,3,['83.040.10'],ISO/TC 45/SC 3,9599,[6427],[43710],"['en','fr']",5,

43710,IS,,ISO 1795:2007,"Rubber, raw natural and raw synthetic — Sampling and further preparative procedures","Caoutchouc, naturel brut et synthétique brut — Méthodes d'échantillonnage et de préparation ultérieure",2007-05-07,4,['83.040.10'],ISO/TC 45/SC 3,9599,[31520],[70280],['en'],5,"<p>ISO 1795:2007 specifies a method for the sampling of raw rubber in bales, blocks or packages and further procedures carried out on the samples to prepare test samples for chemical and physical tests.</p>"

6428,IS,,ISO 1796:1982,"Rubber, raw — Sample preparation",Caoutchoucs bruts — Préparation des échantillons,1982-03-01,3,['83.040.10'],ISO/TC 45/SC 3,9599,[4144],[6427],"['en','fr']",4,

6431,IS,,ISO 1797-1:1992,Dental rotary instruments — Shanks — Part 1: Shanks made of metals,Instruments rotatifs dentaires — Queues — Partie 1: Queues en matériaux métalliques,1992-01-30,1,['11.060.20'],ISO/TC 106/SC 4,9599,[6430],[51955],"['en','fr']",6,<p>Specifies four types. Gives measurement methods for the verification of dimensions. Includes quality control requirements.</p>

23678,IS,Amd,ISO 1797-1:1992/Amd 1:1997,Dental rotary instruments — Shanks — Part 1: Shanks made of metals — Amendment 1,Instruments rotatifs dentaires — Queues — Partie 1: Queues en matériaux métalliques — Amendement 1,1997-12-18,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[51955],"['en','fr']",1,

51955,IS,,ISO 1797-1:2011,Dentistry — Shanks for rotary instruments — Part 1: Shanks made of metals,Médecine bucco-dentaire — Queues pour instruments rotatifs — Partie 1: Queues en matériaux métalliques,2011-08-10,2,['11.060.20'],ISO/TC 106/SC 4,9599,"[23678,6431]",[63866],"['en','fr']",9,<p>ISO 1797-1:2011 specifies shanks for rotary instruments used in dentistry and gives measurement methods for the verification of dimensions.</p>

6429,IS,,ISO 1797:1976,Dental burs and cutters — Fitting dimensions,Fraises et instruments de coupe utilisés en art dentaire — Dimensions d'ajustement,1976-03-01,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[6430],"['en','fr']",2,

6430,IS,,ISO 1797:1985,Dental rotary instruments — Shanks,Instruments rotatifs dentaires — Queues,1985-09-19,2,['11.060.20'],ISO/TC 106/SC 4,9599,[6429],"[6431,6432]",['en'],4,

6432,IS,,ISO 1797-2:1992,Dental rotary instruments — Shanks — Part 2: Shanks made of plastics,Instruments rotatifs dentaires — Queues — Partie 2: Queues en matières plastiques,1992-01-30,1,['11.060.20'],ISO/TC 106/SC 4,9599,[6430],[63866],"['en','fr']",5,<p>Specifies four types. Gives measurement methods for the verification of dimensions. Includes quality control requirements.</p>

55931,IS,,ISO 1797-3:2013,Dentistry — Shanks for rotary instruments — Part 3: Shanks made of ceramics,Médecine bucco-dentaire — Queues pour instruments rotatifs — Partie 3: Queues en céramique,2013-03-12,1,['11.060.20'],ISO/TC 106/SC 4,9599,,[63866],"['en','fr']",8,<p>ISO 1797-3:2013 specifies ceramic shanks of rotary instruments used in dentistry and gives measurement methods for the verification of the dimensions.</p>

61503,IS,,ISO 17972-4:2015,Graphic technology — Colour data exchange format (CxF/X) — Part 4: Spot colour characterisation data (CxF/X-4),Technologie graphique — Échange des données de couleur en utilisant CxF — Partie 4: Données de caractérisation des points de couleur,2015-06-24,1,"['35.240.30','37.100.99']",ISO/TC 130,9599,,[71110],['en'],12,<p>ISO 17972-4:2015 defines an exchange format for spectral measurement data of inks to provide a means to characterise spot colour inks to allow reliable printing and proofing of products that have been designed using these inks. Only isotropic (paper-like) substrates are within the scope of this part of ISO 17972 which is limited to application area

31658,IS,,ISO 17973:2002,Surface chemical analysis — Medium-resolution Auger electron spectrometers — Calibration of energy scales for elemental analysis,Analyse chimique des surfaces — Spectromètres d'électrons Auger à résolution moyenne — Étalonnage des échelles d'énergie pour l'analyse élémentaire,2002-10-24,1,['71.040.40'],ISO/TC 201/SC 7,9599,,[71084],"['en','fr']",11,"<p>ISO 17973:2002 specifies a method for calibrating the kinetic energy scales of Auger electron spectrometers with an uncertainty of 3 eV, for general analytical use in identifying elements at surfaces. In addition, it specifies a method for establishing a calibration schedule. It is applicable to instruments used in eit

71084,IS,,ISO 17973:2016,Surface chemical analysis — Medium-resolution Auger electron spectrometers — Calibration of energy scales for elemental analysis,Analyse chimique des surfaces — Spectromètres d'électrons Auger à résolution moyenne — Étalonnage des échelles d'énergie pour l'analyse élémentaire,2016-09-05,2,['71.040.40'],ISO/TC 201/SC 7,9599,[31658],[86468],['en'],11,"<p>ISO 17973:2016 specifies a method for calibrating the kinetic energy scales of Auger electron spectrometers with an uncertainty of 3 eV, for general analytical use in identifying elements at surfaces. In addition, it specifies a method for establishing a calibration schedule. It is applicable to instruments used in eit

6433,IS,,ISO 1798:1983,"Polymeric materials, cellular flexible — Determination of tensile strength and elongation at break",Matériaux polymères alvéolaires souples - Détermination de la résistance à la traction et de l'allongement à la rupture,1983-12-01,2,['83.100'],ISO/TC 45,9599,,[2346],"['en','fr']",2,

2346,IS,,ISO 1798:1997,Flexible cellular polymeric materials — Determination of tensile strength and elongation at break,Matériaux polymères alvéolaires souples — Détermination de la résistance à la traction et de l'allongement à la rupture,1997-09-11,3,['83.100'],ISO/TC 45/SC 4,9599,[6433],[41059],"['en','fr']",4,

38352,IS,Cor,ISO 1798:1997/Cor 1:2003,Flexible cellular polymeric materials — Determination of tensile strength and elongation at break — Technical Corrigendum 1,Matériaux polymères alvéolaires souples — Détermination de la résistance à la traction et de l'allongement à la rupture — Rectificatif technique 1,2003-03-19,3,['83.100'],ISO/TC 45/SC 4,9599,,[41059],"['en','fr']",2,

56093,IS,,ISO 17984:2014,Machine-made textile floor coverings — Determination of dimensional changes after exposure to heat and/or water,Revêtements de sol textiles fabriqués à la machine — Détermination de la variation dimensionnelle après exposition à la chaleur et/ou à l'eau,2014-06-17,1,['97.150'],ISO/TC 219,9599,[33294],[67633],['en'],9,"<p>ISO 17984:2014 specifies procedures for the determination of both planar and out-of-plane dimensional changes that take place when machine-made textile floor coverings are subjected to heat, water, or varied heat and water conditions.</p><p>The following methods are applicable to all machine-made textile floor coverings including those produced in ti

61222,IS,,ISO 17987-1:2016,Road vehicles — Local Interconnect Network (LIN) — Part 1: General information and use case definition,Véhicules routiers — Réseau Internet local (LIN) — Partie 1: Information générale et définition des cas d'usage,2016-08-04,1,['43.040.15'],ISO/TC 22/SC 31,9599,,[85125],['en'],8,"<p>ISO 17987-1:2016 gives an overview of the structure and the partitioning of ISO 17987 (all parts). In addition, it outlines the use case where the ISO 17987 (all parts) will be used. The terminology defined in ISO 17987-1:2016 is common for all LIN communication systems and is used throughout ISO 17987 (all parts).</p><p>It has been established in order to define the use cases for LIN.

61223,IS,,ISO 17987-2:2016,Road vehicles — Local Interconnect Network (LIN) — Part 2: Transport protocol and network layer services,Véhicules routiers — Réseau Internet local (LIN) — Partie 2: Protocole de transport et couches de services réseau,2016-08-04,1,"['35.240.60','43.040.15']",ISO/TC 22/SC 31,9599,,[85126],['en'],72,"<p>ISO 17987-2:2016 specifies a transport protocol and network layer services tailored to meet the requirements of LIN‑based vehicle network systems on local interconnect networks. The protocol specifies an unconfirmed communication.</p><p>The LIN protocol supports the standardized service primitive interface as specified in ISO 14229‑2.</p><p>ISO 17987-2:2016 provides

61224,IS,,ISO 17987-3:2016,Road vehicles — Local Interconnect Network (LIN) — Part 3: Protocol specification,Véhicules routiers — Réseau Internet local (LIN) — Partie 3: Spécification du protocole,2016-08-05,1,['43.040.15'],ISO/TC 22/SC 31,9599,,[85127],['en'],44,"<p>ISO 17987-3:2016 specifies the LIN protocol including the signal management, frame transfer, schedule table handling, task behaviour and status management and LIN master and slave node. It contains also OSI layer 5 properties according to ISO 14229‑7 UDSonLIN-based node configuration and identification services (SID: B016 to B816) belonging to the core protocol specification.</p><p>A node (normally a master node) that is connect

61225,IS,,ISO 17987-4:2016,Road vehicles — Local Interconnect Network (LIN) — Part 4: Electrical physical layer (EPL) specification 12 V/24 V,Véhicules routiers — Réseau Internet local (LIN) — Partie 4: Spécification de la couche électrique physique (EPL) 12V/24V,2016-08-25,1,['43.040.15'],ISO/TC 22/SC 31,9599,,[85128],['en'],27,<p>ISO 17987-4:2016 specifies the 12 V and 24 V electrical physical layers (EPL) of the LIN communications system.</p><p>The electrical physical layer for LIN is designed for low-cost networks with bit rates up to 20 kbit/s to connect automotive electronic control units (ECUs). The medium that is used is a single wire for each receiver and transmitter with reference

61227,IS,,ISO 17987-6:2016,Road vehicles — Local Interconnect Network (LIN) — Part 6: Protocol conformance test specification,Véhicules routiers — Réseau Internet local (LIN) — Partie 6: Spécification du protocole d'essai de conformité,2016-10-06,1,['43.040.15'],ISO/TC 22/SC 31,9599,,[85129],['en'],66,"<p>ISO 17987-6:2016 specifies the LIN protocol conformance test. This test verifies the conformance of LIN communication controllers with respect to ISO 17987‑2 and ISO 17987‑3.</p><p>ISO 17987-6:2016 provides all necessary technical information to ensure that test results are identical even on different test systems, provided that the particular test suite and the test system are compliant to

61229,IS,,ISO 17987-7:2016,Road vehicles — Local Interconnect Network (LIN) — Part 7: Electrical Physical Layer (EPL) conformance test specification,Véhicules routiers — Réseau Internet local (LIN) — Partie 7: Spécification d'essai de conformité de la couche électrique physique (EPL),2016-12-14,1,['43.040.15'],ISO/TC 22/SC 31,9599,,[85130],['en'],172,"<p>ISO 17987-7:2016 specifies the conformance test for the electrical physical layer (EPL) of the LIN communications system. It is part of this document to define a test that considers ISO 9646 and ISO 17987‑4.</p><p>The purpose of ISO 17987-7:2016 is to provide a standardized way to verify whether a LIN bus driver is compliant to ISO 17987?4.

31667,IS,,ISO 17994:2004,Water quality — Criteria for establishing equivalence between microbiological methods,Qualité de l'eau — Critères permettant d'établir l'équivalence de méthodes microbiologiques,2004-05-14,1,"['13.060.70','07.100.20']",ISO/TC 147/SC 4,9599,,[56617],"['en','fr']",18,<p>ISO 17994:2004 defines an evaluation procedure for comparing two methods intended for the detection or quantification of the same target group or species of microorganisms.</p><p>ISO 17994:2004 provides the mathematical basis for the evaluation of the average relative performance of two methods against chosen criteria of equivalence. </p><p>Any two enumeration methods based on counts (of colonies or pos

42082,IS,,ISO 17995:2005,Water quality — Detection and enumeration of thermotolerant Campylobacter species,Qualité de l'eau — Recherche et dénombrement d'espèces thermotolérantes du genre Campylobacter,2005-06-27,1,['07.100.20'],ISO/TC 147/SC 4,9599,,[69047],['en'],14,<p>ISO 17995:2005 specifies a method for the detection and semiquantitative enumeration of thermotolerant <i>Campylobacter</i> species. The method can be applied to all kinds of filterable waters.</p><p>The method can also be used as a presence/absence test for <i>Campylobacter</i> species in a specified sample volume.</p>

4019,IS,,ISO 180:1982,Plastics — Determination of Izod impact strength of rigid materials,Plastiques — Détermination de la résistance au choc Izod des matières rigides,1982-12-01,1,['83.080.01'],ISO/TC 61/SC 2,9599,,[4020],"['en','fr']",8,

4020,IS,,ISO 180:1993,Plastics — Determination of Izod impact strength,Plastiques — Détermination de la résistance au choc Izod,1993-05-06,2,['83.080.01'],ISO/TC 61/SC 2,9599,[4019],[26802],"['en','fr']",11,

25663,IS,Cor,ISO 180:1993/Cor 1:1995,Plastics — Determination of Izod impact strength — Technical Corrigendum 1,Plastiques — Détermination de la résistance au choc Izod — Rectificatif technique 1,1995-03-02,2,['83.080.01'],ISO/TC 61/SC 2,9599,,[26802],"['en','fr']",1,

26802,IS,,ISO 180:2000,Plastics — Determination of Izod impact strength,Plastiques — Détermination de la résistance au choc Izod,2000-12-14,3,['83.080.01'],ISO/TC 61/SC 2,9599,"[25663,4020]","[72820,52843]","['en','fr']",10,

38233,IS,Amd,ISO 180:2000/Amd 1:2006,Plastics — Determination of Izod impact strength — Amendment 1,Plastiques — Détermination de la résistance au choc Izod — Amendement 1,2006-11-28,3,['83.080.01'],ISO/TC 61/SC 2,9599,,"[72820,52843]","['en','fr']",2,

60777,IS,Amd,ISO 180:2000/Amd 2:2013,Plastics — Determination of Izod impact strength — Amendment 2: Precision data,Plastiques — Détermination de la résistance au choc Izod — Amendement 2: Données de fidélité,2013-04-04,3,['83.080.01'],ISO/TC 61/SC 2,9599,,[72820],"['en','fr']",4,

72820,IS,,ISO 180:2019,Plastics — Determination of Izod impact strength,Plastiques — Détermination de la résistance au choc Izod,2019-11-29,4,['83.080.01'],ISO/TC 61/SC 2,9599,"[26802,38233,60777]",[84394],"['en','fr']",13,"<p><b>1.1</b> This document specifies a method for determining the Izod impact strength of plastics under defined conditions. A number of different types of specimen and test configurations are defined. Different test parameters are specified according to the type of material, the type of test specimen and the type of notch.</p><p><b>1.2</b> The method is used to investigate the behaviour of specified types of specimen under the impact conditions defined and for estimat

6436,IS,,ISO 1802:1974,Natural rubber latex — Determination of boric acid,Latex de caoutchouc naturel — Dosage de l'acide borique,1974-03-01,1,['83.040.10'],ISO/TC 45,9599,,"[6437,6438]","['en','fr']",2,

6437,IS,,ISO 1802:1985,Natural rubber latex concentrate — Determination of boric acid content,Latex concentré de caoutchouc naturel — Dosage de l'acide borique,1985-11-07,2,['83.040.10'],ISO/TC 45/SC 3,9599,[6436],[6438],"['en','fr']",2,

6441,IS,,ISO 1803-1:1985,Building construction — Tolerances — Vocabulary — Part 1: General terms,Construction immobilière — Tolérances — Vocabulaire — Partie 1: Termes généraux,1985-07-04,1,"['01.040.91','91.010.30']",ISO/TC 59,9599,[6439],[6440],"['en','fr']",4,

6439,IS,,ISO 1803:1973,Tolerances for building — Vocabulary,Tolérances pour le bâtiment — Vocabulaire,1973-11-01,1,"['01.040.91','91.010.30']",ISO/TC 59,9599,,"[6441,6442]","['en','fr']",8,

6440,IS,,ISO 1803:1997,Building construction — Tolerances — Expression of dimensional accuracy — Principles and terminology,Construction immobilière — Tolérances — Expression de l'exactitude dimensionnelle — Principes et terminologie,1997-10-02,2,"['01.040.91','91.010.30']",ISO/TC 59/SC 2,9599,"[6441,6442,10359]",[77077],"['en','fr']",10,"<p>This International Standard describes the basic principles for the expression of dimensional</p><p>deviation in building, and defines the basic terms and definitions relating to the evaluation,</p><p>specification and verification of accuracy.</p><p>It is applicable to the manufacture of building components (standard or purpose made), the</p><p>setting o

6442,IS,,ISO 1803-2:1986,Building construction — Tolerances — Vocabulary — Part 2: Derived terms,Construction immobilière — Tolérances — Vocabulaire — Partie 2: Termes dérivés,1986-09-18,1,"['01.040.91','91.010.30']",ISO/TC 59,9599,[6439],[6440],"['en','fr']",3,

6443,IS,,ISO 1804:1972,Doors — Terminology,Portes — Terminologie,1972-05-01,1,"['01.040.91','91.060.50']",ISO/TC 162,9599,,"[73331,53696]","['en','fr']",8,

6444,IS,,ISO 1805:1973,Fishing nets — Determination of breaking load and knot breaking load of netting yarns,Filets de pêche — Détermination de la force de rupture et de la force de rupture au noeud des fils pour filets,1973-07-01,1,['65.150'],ISO/TC 38,9599,,[30041],"['en','fr']",4,<p>The tests may be carried out in both the dry and wet states but tests in wet state on the knotted yarn are considered to be particularly appropriate in indicating the behaviour of the yarn in use. A length of yarn is extended in the dry or wet state until it reaches the load at rupture. The test is performed using a suitable apparatus that records or indicates the applied load. - Replaces ISO Recommendation R

6445,IS,,ISO 1806:1973,Fishing nets — Determination of mesh breaking load of netting,Filets de pêche — Détermination de la force de rupture de la maille de nappe de filet,1973-07-01,1,['65.150'],ISO/TC 38,9599,,[28360],"['en','fr']",4,<p>The tests may be carried out in both the dry and wet states but tests in wet state are considered to be particularly appropriate in indicating the behaviour of the netting in use. A mesh is extended in the dry or wet state until one of the knots or joints reaches the load at rupture. The test is performed using a suitable apparatus that records or indicates the applied load. - Replaces ISO Recommendation R 1806-1970.</p>

33352,IS,,ISO 18064:2003,Thermoplastic elastomers — Nomenclature and abbreviated terms,Élastomères thermoplastiques — Nomenclature et termes abrégés,2003-09-17,1,"['83.080.20','01.040.83']",ISO/TC 45,9599,,[65365],"['en','fr']",5,"<p>ISO 18064:2003 establishes a nomenclature system for thermoplastic elastomers based on the chemical composition of the polymer or polymers involved. It defines symbols and abbreviated terms used to identify thermoplastic elastomers in industry, commerce and government. It is not intended to conflict with, but to supplement, existing trade names and trademarks.</p><p>Thermoplastic-elastomer abbreviated terms that have been used in the past are given in an Annex.<

65365,IS,,ISO 18064:2014,Thermoplastic elastomers — Nomenclature and abbreviated terms,Élastomères thermoplastiques — Nomenclature et termes abrégés,2014-11-28,2,"['83.080.20','01.040.83']",ISO/TC 45,9599,[33352],"[80849,80440]","['en','fr']",5,"<p>ISO 18064:2014 establishes a nomenclature system for thermoplastic elastomers based on the chemical composition of the polymer or polymers involved. It defines symbols and abbreviated terms used to identify thermoplastic elastomers in industry, commerce, and government. It is not intended to conflict with, but to supplement, existing trade names and trademarks.</p>"

61295,IS,,ISO 18077:2018,Reload startup physics tests for pressurized water reactors,Essais physiques au redémarrage pour les réacteurs à eau préssurisée,2018-03-27,1,['27.120.10'],ISO/TC 85/SC 6,9599,,[76878],['en'],28,"<p>ISO 18077:2018 applies to the reactor physics tests that are performed following a refuelling or other core alteration of a PWR for which nuclear design calculations are required. This document does not address the physics test program for the initial core of a commercial PWR[1].</p><p>ISO 18077:2018 specifies the minimum acceptable startup reactor physics test program to determine if the operating characteristics of the core are consistent with the design predictions, wh

61326,IS,,ISO 18081:2016,Non-destructive testing — Acoustic emission testing (AT) — Leak detection by means of acoustic emission,Essais non destructifs — Contrôle par émission acoustique — Détection de fuites par émission acoustique,2016-05-24,1,['19.100'],ISO/TC 135/SC 9,9599,,[84936],"['en','fr']",28,"<p>ISO 18081:2016 specifies the general principles required for leak detection by acoustic emission testing (AT). It is addressed to the application of the methodology on structures and components, where a leak flow as a result of pressure differences appears and generates acoustic emission (AE).</p><p>It describes phenomena of the AE generation and influence of the nature of fluids, shape of

33301,IS,,ISO 18084:2005,Press tools for tablets — Punches and dies,Outillage de presse pour comprimés — Poinçons et matrices,2005-10-03,1,['25.120.10'],ISO/TC 29/SC 8,9599,,[57880],"['en','fr','ru']",13,"<p>ISO 18084:2005 specifies the main dimensions, tolerances and characteristics of punches and dies for all kinds of tablets. It deals with measures that are relevant for the interchangeability of the press punches between the different tableting machines of various manufacturers.</p>"

61335,IS,,ISO 18086:2015,Corrosion of metals and alloys — Determination of AC corrosion — Protection criteria,Corrosion des métaux et alliages — Détermination de la corrosion occasionnée par les courants alternatifs — Critères de protection,2015-06-04,1,['77.060'],ISO/TC 156,9599,,[78148],"['en','fr']",38,"<p>ISO 18086:2015 is applicable to buried cathodically-protected pipeline that is influenced by AC traction systems and/or AC power lines.</p><p>In the presence of AC interference, the protection criteria given in ISO 15589 1 are not sufficient to demonstrate that the steel is being protected against corrosion.</p><p>ISO 18086:2015 provides limits, measurement procedures, mitigation measur

61386,IS,,ISO 18091:2014,Quality management systems — Guidelines for the application of ISO 9001:2008 in local government,Systèmes de management de la qualité — Lignes directrices pour l'application de l'ISO 9001:2008 à la collectivité locale,2014-02-10,1,"['03.100.70','03.160']",ISO/TC 176,9599,[53504],[72808],"['ar','en','es']",57,"<p>The objective of ISO 18091:2014 is to provide local governments with guidelines for achieving reliable results through the application of ISO 9001:2008 on an integral basis. These guidelines do not, however, add, change or modify the requirements of ISO 9001:2008.</p><p>All the guidelines indicated in ISO 18091:2014 are generic and applicable to all local gov

61425,IS,,ISO 18096:2013,Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature for preformed pipe insulation,Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles — Détermination de la température maximale de service des coquilles isolantes préformées,2013-03-01,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[81149],['en'],16,<p>ISO 18096:2013 specifies the equipment and procedures for determining the maximum service temperature for preformed pipe insulation. It is applicable to thermal insulating products.</p>

61426,IS,,ISO 18097:2013,Thermal insulating products for building equipment and industrial installations — Determination of maximum service temperature,Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles — Détermination de la température maximale de service,2013-02-27,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[81150],['en'],17,<p>ISO 18097:2013 specifies the equipment and procedures for determining the maximum service temperature of flat insulation products. It is applicable to thermal insulating products.</p>

61427,IS,,ISO 18098:2013,Thermal insulating products for building equipment and industrial installations — Determination of the apparent density of preformed pipe insulation,Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles — Détermination de la masse volumique apparente des coquilles isolantes préformées,2013-04-05,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[81153],['en'],4,<p>ISO 18098:2013 specifies the equipment and procedures for determining the apparent overall density and the apparent core density under reference conditions. It is applicable to full-size thermal insulating products and test specimens of preformed pipe insulation.</p>

61428,IS,,ISO 18099:2013,Thermal insulating products for building equipment and industrial installations — Determination of the coefficient of thermal expansion,Produits isolants thermiques pour l'équipement du bâtiment et les installations industrielles — Détermination du coefficient de dilatation thermique,2013-04-05,1,['91.100.60'],ISO/TC 163/SC 1,9599,,[81152],['en'],8,"<p>ISO 18099:2013 specifies the equipment and procedures for determining the coefficient of linear thermal expansion. It is applicable to thermal insulating products within the temperature range 196 °C to 850 °C, subject to the possible temperature limitation of the test specimens. It is not applicable to products which e

6448,IS,,ISO 1810:1976,Copper alloys — Determination of nickel (low contents) — Dimethylglyoxime spectrophotometric method,Alliages de cuivre — Dosage du nickel (faibles teneurs) — Méthode spectrophotométrique à la diméthylglyoxime,1976-11-01,1,['77.120.30'],ISO/TC 26,9599,,[6449],"['en','fr']",2,"<p>The method is applicable to the determination of nickel contents up to 2.5 % (m/m). Covers principle, reagents, apparatus, sampling, procedure, expression of results, and test report.</p>"

33309,IS,,ISO 18104:2003,Health informatics — Integration of a reference terminology model for nursing,Informatique de santé — Intégration d'un modèle de terminologie de référence pour les soins infirmiers,2003-12-08,1,['35.240.80'],ISO/TC 215,9599,,[59431],"['en','fr']",28,"<p>The purpose of ISO 18104:2003 is to establish a nursing reference terminology model consistent with the goals and objectives of other specific health terminology models in order to provide a more unified reference health model. This International Standard includes the development of reference terminology models for nursing diagnoses and nursing actions and relevant terminology and definitions for its implementation.</

59431,IS,,ISO 18104:2014,Health informatics — Categorial structures for representation of nursing diagnoses and nursing actions in terminological systems,Informatique de santé — Structures catégorielles destinées à la représentation des diagnostics infirmiers et des actions infirmières dans les systèmes terminologiques,2014-01-27,2,['35.240.80'],ISO/TC 215,9599,[33309],[81132],"['en','fr']",30,"<p>ISO 18104:2014 specifies the characteristics of two categorial structures, with the overall aim of supporting interoperability in the exchange of meaningful information between information systems in respect of nursing diagnoses and nursing actions. Categorial structures for nursing diagnoses and n

40984,IS,,ISO 18113-1:2009,"In vitro diagnostic medical devices — Information supplied by the manufacturer (labelling) — Part 1: Terms, definitions and general requirements","Dispositifs médicaux de diagnostic in vitro — Informations fournies par le fabricant (étiquetage) — Partie 1: Termes, définitions et exigences générales",2009-12-09,1,['11.100.10'],ISO/TC 212,9599,,[79866],"['en','fr','ru']",49,"<p>ISO 18113-1:2009 defines concepts, establishes general principles and specifies essential requirements for information supplied by the manufacturer of <i>in vitro</i> diagnostic (IVD) medical devices.</p>"

40985,IS,,ISO 18113-2:2009,In vitro diagnostic medical devices — Information supplied by the manufacturer (labelling) — Part 2: In vitro diagnostic reagents for professional use,Dispositifs médicaux de diagnostic in vitro — Informations fournies par le fabricant (étiquetage) — Partie 2: Réactifs de diagnostic in vitro à usage professionnel,2009-12-09,1,['11.100.10'],ISO/TC 212,9599,,[79867],"['en','fr','ru']",10,<p>ISO 18113-2:2009 specifies requirements for information supplied by the manufacturer of <i>in vitro</i> diagnostic (IVD) reagents for professional use.</p><p>ISO 18113-2:2009 also applies to information supplied by the manufacturer with calibrators and control materials intended f

40986,IS,,ISO 18113-3:2009,In vitro diagnostic medical devices — Information supplied by the manufacturer (labelling) — Part 3: In vitro diagnostic instruments for professional use,Dispositifs médicaux de diagnostic in vitro — Informations fournies par le fabricant (étiquetage) — Partie 3: Instruments de diagnostic in vitro à usage professionnel,2009-12-09,1,['11.100.10'],ISO/TC 212,9599,,[79868],"['en','fr','ru']",9,"<p>ISO 18113-3:2009 specifies requirements for information supplied by the manufacturer of <i>in vitro</i> dignostic (IVD)<i> </i>instruments for professional use.</p><p>ISO 18113-3:2009 also applies to apparatus and equipment intended to be used with IVD<i> </i>instruments for

40987,IS,,ISO 18113-4:2009,In vitro diagnostic medical devices — Information supplied by the manufacturer (labelling) — Part 4: In vitro diagnostic reagents for self-testing,Dispositifs médicaux de diagnostic in vitro — Informations fournies par le fabricant (étiquetage) — Partie 4: Réactifs de diagnostic in vitro pour auto-tests,2009-12-17,1,['11.100.10'],ISO/TC 212,9599,,[79869],"['en','fr','ru']",10,"<p>ISO 18113-4:2009 specifies requirements for information supplied by the manufacturer of <i>in vitro</i> diagnostic (IVD) reagents for self-testing.</p><p>ISO 18113-4:2009 also applies to information supplied by the manufacturer with calibrators and control materials intended for use with I

40988,IS,,ISO 18113-5:2009,In vitro diagnostic medical devices — Information supplied by the manufacturer (labelling) — Part 5: In vitro diagnostic instruments for self-testing,Dispositifs médicaux de diagnostic in vitro — Informations fournies par le fabricant (étiquetage) — Partie 5: Instruments de diagnostic in vitro pour auto-tests,2009-12-09,1,['11.100.10'],ISO/TC 212,9599,,[79870],"['en','fr','ru']",8,<p>ISO 18113-5:2009 specifies requirements for information supplied by the manufacturer of <i>in vitro</i> diagnostic (IVD) instruments for self-testing.</p><p>ISO 18113-5:2009 also applies to apparatus and equipment intended to be used with IVD instruments for self-testing.</p><p>ISO 181

31693,IS,,ISO 18114:2003,Surface chemical analysis — Secondary-ion mass spectrometry — Determination of relative sensitivity factors from ion-implanted reference materials,Analyse chimique des surfaces — Spectrométrie de masse des ions secondaires — Détermination des facteurs de sensibilité relative à l'aide de matériaux de référence à ions implantés,2003-04-14,1,['71.040.40'],ISO/TC 201/SC 6,9599,,[80189],['en'],4,"<p>ISO 18114:2003 specifies a method of determining relative sensitivity factors (RSFs) for secondary-ion mass spectrometry (SIMS) from ion-implanted reference materials.</p><p>The method is applicable to specimens in which the matrix is of uniform chemical composition, and in wh

46578,IS,,ISO 18115-1:2010,Surface chemical analysis — Vocabulary — Part 1: General terms and terms used in spectroscopy,Analyse chimique des surfaces — Vocabulaire — Partie 1: Termes généraux et termes utilisés en spectroscopie,2010-07-08,1,"['71.040.40','01.040.71']",ISO/TC 201/SC 1,9599,"[29189,43171,37193]",[63783],"['en','fr']",103,"<p>ISO 18115 is a vocabulary, published in two parts, which defines terms for surface chemical analysis. ISO 18115-1:2010 covers general terms and those used in spectroscopy while ISO 18115-2:2010 covers terms used in scanning-probe microscopy.</p>"

63783,IS,,ISO 18115-1:2013,Surface chemical analysis — Vocabulary — Part 1: General terms and terms used in spectroscopy,Analyse chimique des surfaces — Vocabulaire — Partie 1: Termes généraux et termes utilisés en spectroscopie,2013-11-04,2,"['71.040.40','01.040.71']",ISO/TC 201/SC 1,9599,"[60267,46578]",[74811],['en'],104,<p>ISO 18115-1:2013 defines terms for surface chemical analysis. It covers general terms and those used in spectroscopy.</p>

46579,IS,,ISO 18115-2:2010,Surface chemical analysis — Vocabulary — Part 2: Terms used in scanning-probe microscopy,Analyse chimique des surfaces — Vocabulaire — Partie 2: Termes utilisés en microscopie à sonde à balayage,2010-07-08,1,"['71.040.40','01.040.71']",ISO/TC 201/SC 1,9599,"[29189,43171,37193]",[63784],"['en','fr']",49,"<p>ISO 18115 is a vocabulary, published in two parts, which defines terms for surface chemical analysis. ISO 18115-1:2010 covers general terms and those used in spectroscopy while ISO 18115-2:2010 covers terms used in scanning-probe microscopy.</p>"

63784,IS,,ISO 18115-2:2013,Surface chemical analysis — Vocabulary — Part 2: Terms used in scanning-probe microscopy,Analyse chimique des surfaces — Vocabulaire — Partie 2: Termes utilisés en microscopie à sonde à balayage,2013-11-04,2,"['71.040.40','01.040.71']",ISO/TC 201/SC 1,9599,"[46579,60266]",[83146],['en'],45,<p>ISO 18115-2:2013 defines terms for surface chemical analysis.</p>

29189,IS,,ISO 18115:2001,Surface chemical analysis — Vocabulary,Analyse chimique des surfaces — Vocabulaire,2001-07-05,1,"['71.040.40','01.040.71']",ISO/TC 201/SC 1,9599,,"[46578,46579]","['en','fr']",57,

37193,IS,Amd,ISO 18115:2001/Amd 1:2006,Surface chemical analysis — Vocabulary — Amendment 1,Analyse chimique des surfaces — Vocabulaire — Amendement 1,2006-01-19,1,"['71.040.40','01.040.71']",ISO/TC 201/SC 1,9599,,"[46578,46579]","['en','fr']",20,

43171,IS,Amd,ISO 18115:2001/Amd 2:2007,Surface chemical analysis — Vocabulary — Amendment 2,Analyse chimique des surfaces — Vocabulaire — Amendement 2,2007-12-13,1,"['71.040.40','01.040.71']",ISO/TC 201/SC 1,9599,,"[46578,46579]","['en','fr']",51,