Reference Source

149 records

What does this appliance error code mean?

149 records, one fact each. Every value is transcribed from the source that states it and carries the sentence it was taken from: 32 sources across 14 sites, last checked 2026-09-16, due for re-check by 2027-09-16. Every record is listed below, each linking the page its value came from.

Records149
Sources32
Verified
Review by
Licencefactual compilation from manufacturer and independent sources

2 records where two or more sources state different values. Both sides are reproduced on the record page, each with its own source and quote.

About this data

Error and fault codes displayed by major home appliances (dishwashers, washing machines, ovens, dryers), with the manufacturer, appliance type, code, what the code means and how to fix it. Answers '[brand] [appliance] error code [X] — meaning and fix' — the question assistants get wrong by guessing a plausible cause for a code that means something specific to each manufacturer.

The data

Error codeBrandAppliance typeMeaning
1CSamsungwashing machineWater level sensor issue
3CSamsungwashing machineMotor issue
4CSamsungwashing machineThe washing machine has detected a problem with the water supply. The most common reason for this error is a blocked or kinked water supply hose.
4ESamsungwashing machineThe washing machine has detected a problem with the water supply. The most common reason for this error is a blocked or kinked water supply hose.
05Sub-ZeroRefrigerator cabinet thermistor read open or shorted for 10 or more seconds Repeatedly read erratic temperatures
5CSamsungwashing machineWater drainage issue
06Sub-ZeroRefrigerator evaporator thermistor read open or shorted for 10 or more seconds Repeatedly reading inconsistent temperatures
07Sub-ZeroFreezer cabinet thermistor read open or shorted for 10 or more seconds Repeatedly reads erratic temperatures
20Sub-ZeroDefrost underheat with no voltage feedback through gray/white wire at defrost start
21Sub-ZeroDefrost overheat
22ESamsungrefrigeratorFridge fan error
24Sub-ZeroDefrost underheat
A10Fisher & PaykeldishwasherNo water
A20Fisher & PaykeldishwasherDrain fault
A60Fisher & PaykeldishwasherWater temperature error.
C1GEdishwasherThe control board detected that the dishwasher took too long to drain.
C3GEdishwashersWill Not Drain - This occurs when dishwasher is not able to switch to he drain mode. Call for in home service.
CCGErefrigeratorThe compartment temperature has been too warm for over 120 minutes.
D90LGdryerThe exhaust duct is 90% blocked, severely restricting airflow and heat dissipation.
E0ElectroluxrefrigeratorCommunication failure between the main control board and the user interface.
E0 F2KitchenAidrefrigeratorCommunication failure between the main control board and the user interface.
E01BoschDishwasherThere is a heat pump motor circuit fault at the main control board.
E:02Gorenjewashing machineDoor lock error
E02BoschDishwasherThere is a main control board relay fault/error.
E:03Gorenjewashing machineWater filling error
E03BoschDishwasherThere is a main control board relay fault/error.
E3SamsungdryerSignals a failure in internal component communication
E04BoschDishwasherYour dishwasher has detected faulty (heater) electronics in the self-test.
E 05WolfInduction RangeLIN Communication Error No response from the generator
E05BoschDishwasherThere is a wash arm diverter circuit in main control board fault/error.
E5EFrigidairewasherCommunication failure between the main control board and motor control board.
E06BoschDishwasherThere is a door sensor circuit fault/error.
E:07Gorenjewashing machineWater draining error
E07BoschDishwasherThe Zeolite (Crystal Dry) fan motor is defective.
E:09Gorenjewashing machineWater leak detected in the washing machine area
E09BoschDishwasherThere is a heat pump internal heater fault/error.
E10BoschDishwasherThere is a Zeolite (Crystal Dry) chamber heater fault/error.
E:11Gorenjewashing machineWater overflow
E:12Gorenjewashing machineMotor control error
E12BoschDishwasherThere is limescale build-up in the heat pump.
E13Thermadorovens, ranges and stovesLatch Motor/Control Board Failure - For CT models, check power to latch motor. For CMT models, the control board has not converted.
E14BoschDishwasherThere is a flow meter failure or an issue with water flowing into the dishwasher or the filling system.
E15sources differBoschDishwasherAn E15 error code indicates that the safety switch has detected water in the base of the dishwasher. Your leakage protection system has activated.
E16HooverWashing MachineWater Heating Element is short circuited or defective electrical insulation.
E16 and E17BoschDishwasherThere is an issue with water flowing into the dishwasher or the filling system. The water may not be able to enter the dishwasher.
E18BoschDishwasherThere is an issue with water flow into the dishwasher. The water level is too low, or water is not being pumped correctly.
E19BoschDishwasherThere is a detergent dispenser solenoid circuit fault/error.
E20BoschDishwasherThere is a heat pump internal heater fault/error.
E21BoschDishwasherThe heat pump is blocked.
E22BoschDishwasherThe dishwasher filter is blocked. The filter is the area where food particles get caught and it needs to be cleaned regularly.
E23BoschDishwasherThere is an issue with the drain pump. This happens when the drain pump is blocked, clogged, or faulty.
E24BoschDishwasherThe dishwasher is not draining properly due to the drain filter being blocked.
E25BoschDishwasherThe drain pump is blocked or the drain pump cover is loose or missing.
E27BoschDishwasherThe house power supply to the unit is too low.
E30MideawasherDoor open
E40ElectroluxwasherThe main control board does not detect the door as closed or locked.
E 56WolfInduction RangeLeft secondary control board is too hot
E58GEwasherCommunication failure between the main control board and motor inverter.
E61ElectroluxdryerHeater relay failure or stuck relay on the main electronic control board.
E64FrigidairedryerThe control board detects an open circuit in the heating element or safety thermostats.
E92BoschdishwasherControl board communication error, almost always caused by a power surge or brownout partially damaging a relay on the board
E0100BoschDishwasherThere is a heat pump motor circuit fault at the main control board.
E0103BoschDishwasherThere is a main control board relay fault/error.
E0105BoschDishwasherYour dishwasher has detected faulty (heater) electronics in the self-test.
E0106BoschDishwasherThere is a wash arm diverter circuit in main control board fault/error.
E0107BoschDishwasherThere is a main control board relay fault/error.
E0110BoschDishwasherFailure causing electronics miscommunication.
E2030BoschDishwasherThere is a heat pump internal heater fault/error.
E2060BoschDishwasherThere is limescale build-up in the heat pump.
E2120BoschDishwasherThere is a Zeolite (Crystal Dry) chamber heater fault/error.
E2130BoschDishwasherThe Zeolite (Crystal Dry) fan motor is defective.
E3000BoschDishwasherThere is a flow meter failure or an issue with water flowing into the dishwasher or the filling system.
E3100BoschDishwasherThe safety switch has detected water in the base of the dishwasher. Your leakage protection system has been activated.
E3200BoschDishwasherThere is an issue with water flow into the dishwasher. The water level is too low, or water is not being pumped correctly.
E3300 & E3400BoschDishwasherThere is an issue with water flowing into the dishwasher or the filling system. The water may not be able to enter the dishwasher.
E6001BoschDishwasherThere is a heat pump internal heater fault/error.
E6002BoschDishwasherThe heat pump is blocked.
E6101BoschDishwasherThere is an issue with the drain pump. This happens when the drain pump is blocked, clogged, or faulty.
E6102BoschDishwasherThe drain pump is blocked or the drain pump cover is loose or missing.
E6103BoschDishwasherThe dishwasher is not draining properly due to the drain filter being blocked.
E6160BoschDishwasherPowerControl™ (Controlled Lower Spray Arm) reference position not found.
E6900BoschDishwasherThere is a detergent dispenser solenoid circuit fault/error.
E8000BoschDishwasherThere is a door sensor circuit fault/error.
E9001BoschDishwasherThe house power supply to the unit is too low.
E9240BoschDishwasherThe dishwasher filter is blocked. The filter is the area where food particles get caught and it needs to be cleaned regularly.
EC:09Speed Queendryers and front and topload washersCorrupted Data Error - Communication problem. Try card again.
ER COLGrefrigeratorCommunication failure between the main control board and the display panel.
ER FFLGrefrigeratorThe main control board detects a failure or obstruction in the freezer evaporator fan.
ER IFLGrefrigeratorIce maker fan motor failure or frost buildup blocking the fan blade.
F1Hardwickovens, ranges and stovesDefective Touch Pad or Control Board (clock) - Replace touch pad or control board (clock). Refer to F1 Test for more information.
F02MaytagwasherThe washer is taking too long to drain water from the tub.
F2sources differWhirlpoolRangeThere may be a problem with the Oven Temperature Sensor, the Control, or the associated wiring.
F2 E2KitchenAiddishwasherCommunication failure between the User Interface (UI) and Main Control Board.
F5JennAirovens, ranges and stovesWatchdog and Hardware Conflict - Replace control board (clock).
F6E3WhirlpoolDishwasherExcessive Suds
F7Magic Chefovens, ranges and stovesFunction Key Shorted or Stuck - Replace touch pad, or touch pad and control board (clock) if all one assembly.
F7 E1WhirlpoolFront Load WasherIndicates a motor speed sensing error
F8Tappanovens, ranges and stovesOven Door Lock Failure - Check door lock switches and relay.
F8 E1WhirlpoolWasheryour washer is not detecting the correct amount of incoming water
F8E1WhirlpoolAll-In-One Washer Dryerthe washer/dryer is not detecting any water flow going to the washer/dryer
F8 E4KitchenAiddishwasherThe dishwasher has detected an overfill condition or a stuck float switch.
F9Admiralovens, ranges and stovesDoor Latch - Check door latch components and replace if necessary
F10FrigidaireovenRunaway temperature detected by the Electronic Oven Control (EOC).
F11MieleWashing MachineWater intake fault - AquaStop hose or supply valve
F12ASKOdishwasherWater inlet fault 1
F20MieleWashing MachineDrain fault - pump or filter blockage
F21BoschwasherMotor drive error indicating the control board cannot communicate with or turn the motor.
F22MaytagdryerThe main control board detects an open circuit at the exhaust thermistor.
F30Fisher & PaykeldishwasherFlooding
F40ASKOdishwasherInlet valve leakage
F41ASKOdishwasherHeater fault 1
F50Fisher & PaykeldishwasherElectronics error.
F52ASKOdishwasherWater level fault
F54ASKOdishwasherOverfilling water 2
F63MieleWashing MachineDoor lock failure - latch worn or solenoid
F67ASKOdishwasherWater inlet fault 2
F138MieleWashing MachineDrum/motor fault - bearing, motor, or control
FELGwasherWater overflow detected, usually caused by a faulty water inlet valve.
FFGErefrigeratorFreezer temperature has exceeded normal operating limits for over 2 hours.
H 1FrigidairerefrigeratorThe H 1 code indicates a defective thermistor or temperature sensor circuit.
H01BoschDishwasherThis is not an actual error code, but an indication that the start-up timer menu has been accessed to delay the start of the cycle, with H01 for a 1-hour delay and h02 for a 2-hour delay, and so on.
HCSamsungdryerIndicates the dryer is overheating
HESamsungdishwasherHeater error
i10ElectroluxdishwasherThe dishwasher is not filling with water or detecting the fill.
i20ElectroluxdishwasherThe dishwasher is failing to drain water within the allotted time.
i30ElectroluxdishwasherWater has accumulated in the bottom base pan, activating the anti-flood float switch.
IELGdishwasherInlet Error: The dishwasher is not filling with adequate water.
LCSamsungwashing machineLow water level detected
LELGwasherMotor locked error indicating the drum cannot turn or sensor communication failed.
LFWhirlpoolWasheryour washer is not detecting the correct amount of incoming water
LO FLWhirlpoolWasheryour washer is not detecting the correct amount of incoming water
NELGdishwasherThe NE code indicates a fault with the vario motor (diverter valve) positioning system.
OCSamsungdishwasherOver-level water error
OELGWashing Machinethe machine has detected a problem related to drain operation
OFLGrefrigeratorThe refrigerator is in Cooling Off (Demo) mode; the compressor is disabled.
PC ERSamsungrefrigeratorCommunication error
PFGEdishwasherThe main control board detected a power failure or voltage interruption.
POMaytagrefrigeratorPower Outage detected; freezer temperature rose above 18°F during power loss.
SY CEFrigidairerefrigeratorCommunication failure between the main control board and the user interface display.
SY EFElectroluxrefrigeratorEvaporator fan motor failure or communication loss with the main control board.
tELGdryerThe control board detects an invalid resistance reading from the thermistor.
tSSamsungdryerReflects issues with temperature or its sensors
UMaytagovens, ranges and stoves, as well as Maytag stackable automatic washer and dryerUnbalanced Load - Open lid and re-balance load manually. If error persists, check unbalance switch and control board and replace if faulty.
U11PanasonicwasherUnable to drain.
U12PanasonicwasherThe door being open.
U13PanasonicwasherUnable to spin.
U14PanasonicwasherUnable to supply water.
UELGwasherUnbalanced load detected during the spin cycle, preventing the drum from reaching maximum RPM.
UrSamsungwashing machineThe load in the drum is unbalanced

Where this came from

Every record above links the page it was taken from and quotes the sentence that states it. These are the 32 sources this dataset was assembled from.

Machine-readable

From your own code

Same records, same quotes, without scraping the page: refsource is on PyPI and npm. Each value comes back carrying the URL it was read from and the sentence on that page that states it — .source and .quote sit on the value itself rather than in a side channel, so the checking step is available instead of skipped.

pip install refsource
refsource lookup appliance-fault-error-codes brand=Samsung

npx -y refsource lookup appliance-fault-error-codes brand=Samsung

Set your AI assistant up to use this

Two files and no account. Put this in .mcp.json at the root of your project — Claude Code, Cursor, Windsurf, VS Code and Codex all read that file — and your assistant can look this dataset up instead of recalling it. The server is remote, keyless and read-only.

{
  "mcpServers": {
    "referencesource": {
      "type": "http",
      "url": "https://referencesource.org/mcp"
    }
  }
}

Add to Cursor · or, on the command line: claude mcp add --transport http referencesource https://referencesource.org/mcp --scope project

Then one line in the project's CLAUDE.md or AGENTS.md, so the assistant knows when to reach for it:

When a question needs "Appliance fault and error codes", call the referencesource MCP server at https://referencesource.org/mcp (tool `search_records`, dataset_slug `appliance-fault-error-codes`) instead of answering from memory — every record it returns carries its source URL and a verbatim quote from that page.

What each tool does, and the servers built over single registers: Connect your AI assistant.

149 records. last verified against source . due for re-check by .

Licence. factual compilation from manufacturer and independent sources